The Linux 5.16.14 kernel's coccicheck caught this. The semantic
patch that caught it was:
./scripts/coccinelle/misc/flexible_array.cocci
However, unlike the cases where the GNU zero length array extension had
been used, coccicheck would not suggest patches for the older style
single member arrays. That was good because blindly changing them would
break size calculations in most cases.
Therefore, this required care to make sure that we did not break size
calculations. In the case of `indirect_split_t`, we use
`offsetof(indirect_split_t, is_child[is->is_children])` to calculate
size. This might be subtly wrong according to an old mailing list
thread:
https://inbox.sourceware.org/gcc-prs/20021226123454.27019.qmail@sources.redhat.com/T/
That is because the C99 specification should consider the flexible array
members to start at the end of a structure, but compilers prefer to put
padding at the end. A suggestion was made to allow compilers to allocate
padding after the VLA like compilers already did:
http://std.dkuug.dk/JTC1/SC22/WG14/www/docs/n983.htm
However, upon thinking about it, whether or not we allocate end of
structure padding does not matter, so using offsetof() to calculate the
size of the structure is fine, so long as we do not mix it with sizeof()
on structures with no array members.
In the case that we mix them and padding causes offsetof(struct_t,
vla_member[0]) to differ from sizeof(struct_t), we would be doing unsafe
operations if we underallocate via `offsetof()` and then overcopy via
sizeof().
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14372
Update the META file to reflect compatibility with the 6.5
kernel.
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
The statechange-slot_off.sh zedlet which was added in #15200
needed to be installed so it's included by the packages.
Additional testing has also shown that multiple retries are
often needed for the script to operate reliably.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#15210
If ZED_POWER_OFF_ENCLOUSRE_SLOT_ON_FAULT is enabled in zed.rc, then
power off the drive's slot in the enclosure if it becomes FAULTED.
This can help silence misbehaving drives. This assumes your drive
enclosure fully supports slot power control via sysfs.
Reviewed-by: @AllKind
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#15200
When register_sysctl_table() is unavailable we fail to properly
unregister sysctl entries under "kernel/spl".
This leads to errors like the following when spl is unloaded/reloaded,
making impossible to properly reload the spl module:
[ 746.995704] sysctl duplicate entry: /kernel/spl/kmem/slab_kvmem_total
Fix by cleaning up all the sub-entries inside "kernel/spl" when the
spl module is unloaded.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Andrea Righi <andrea.righi@canonical.com>
Closes#15239
If we fail to create a proc entry in spl_proc_init() we may end up
calling unregister_sysctl_table() twice: one in the failure path of
spl_proc_init() and another time during spl_proc_fini().
Avoid the double call to unregister_sysctl_table() and while at it
refactor the code a bit to reduce code duplication.
This was accidentally introduced when the spl code was
updated for Linux 6.5 compatibility.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ameer Hamza <ahamza@ixsystems.com>
Signed-off-by: Andrea Righi <andrea.righi@canonical.com>
Closes#15234Closes#15235
Using the filemap_splice_read function for the splice_read handler was
leading to occasional data corruption under certain circumstances. Favor
using copy_splice_read instead, which does not demonstrate the same
erroneous behavior under the tested failure cases.
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#15164
The generic_file_splice_read function was removed in Linux 6.5 in favor
of filemap_splice_read. Add an autoconf test for filemap_splice_read and
use it if it is found as the handler for .splice_read in the
file_operations struct. Additionally, ITER_PIPE was removed in 6.5. This
change removes the ITER_* macros that OpenZFS doesn't use from being
tested in config/kernel-vfs-iov_iter.m4. The removal of ITER_PIPE was
causing the test to fail, which also affected the code responsible for
setting the .splice_read handler, above. That behavior caused run-time
panics on Linux 6.5.
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#15155
Additionally, the .child element of ctl_table has been removed in 6.5.
This change adds a new test for the pre-6.5 register_sysctl_table()
function, and uses the old code in that case. If it isn't found, then
the parentage entries in the tables are removed, and the register_sysctl
call is provided the paths of "kernel/spl", "kernel/spl/kmem", and
"kernel/spl/kstat" directly, to populate each subdirectory over three
calls, as is the new API.
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#15138
This reverts commit b35374fd64 as there
are error messages when loading the SPL module. Errors seemed to be tied
to duplicate a duplicate entry.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Brian Atkinson <batkinson@lanl.gov>
Closes#15134
An iov_iter_type() function to access the "type" member of the struct
iov_iter was added at one point. Move the conditional logic to decide
which method to use for accessing it into a macro and simplify the
zpl_uio_init code.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#15100
The iov_iter->iov member is now iov_iter->__iov and must be accessed via
the accessor function iter_iov(). Create a wrapper that is conditionally
compiled to use the access method appropriate for the target kernel
version.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#15100
Multiple changes to the blkdev API were introduced in Linux 6.5. This
includes passing (void* holder) to blkdev_put, adding a new
blk_holder_ops* arg to blkdev_get_by_path, adding a new blk_mode_t type
that replaces uses of fmode_t, and removing an argument from the release
handler on block_device_operations that we weren't using. The open
function definition has also changed to take gendisk* and blk_mode_t, so
update it accordingly, too.
Implement local wrappers for blkdev_get_by_path() and
vdev_blkdev_put() so that the in-line calls are cleaner, and place the
conditionally-compiled implementation details inside of both of these
local wrappers. Both calls are exclusively used within vdev_disk.c, at
this time.
Add blk_mode_is_open_write() to test FMODE_WRITE / BLK_OPEN_WRITE
The wrapper function is now used for testing using the appropriate
method for the kernel, whether the open mode is writable or not.
Emphasize fmode_t arg in zvol_release is not used
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#15099
When disk_check_media_change() exists, then define
zfs_check_media_change() to simply call disk_check_media_change() on
the bd_disk member of its argument. Since disk_check_media_change()
is newer than when revalidate_disk was present in bops, we should
be able to safely do this via a macro, instead of recreating a new
implementation of the inline function that forces revalidation.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#15101
Additionally, the .child element of ctl_table has been removed in 6.5.
This change adds a new test for the pre-6.5 register_sysctl_table()
function, and uses the old code in that case. If it isn't found, then
the parentage entries in the tables are removed, and the register_sysctl
call is provided the paths of "kernel/spl", "kernel/spl/kmem", and
"kernel/spl/kstat" directly, to populate each subdirectory over three
calls, as is the new API.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#15098
The disk_check_media_change() function was added which replaces
bdev_check_media_change. This change was introduced in 6.5rc1
444aa2c58cb3b6cfe3b7cc7db6c294d73393a894 and the new function takes a
gendisk* as its argument, no longer a block_device*. Thus, bdev->bd_disk
is now used to pass the expected data.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#15060
This change was introduced in Linux commit
7ba150834b840f6f5cdd07ca69a4ccf39df59a66
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#15059
When a kmem cache is exhausted and needs to be expanded a new
slab is allocated. KM_SLEEP callers can block and wait for the
allocation, but KM_NOSLEEP callers were incorrectly allowed to
block as well.
Resolve this by attempting an emergency allocation as a best
effort. This may fail but that's fine since any KM_NOSLEEP
consumer is required to handle an allocation failure.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Adam Moss <c@yotes.com>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Unfortunately, even after e79b6807, I still, much more rarely,
tripped asserts when playing with many ctldir mounts at once.
Since this appears to happen if we dispatched twice too fast, just
ignore it. We don't actually need to do anything if someone already
started doing it for us.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#14462
On Linux, sometimes, when ZFS goes to unmount an automounted snap,
it fails a VERIFY check on debug builds, because taskq_cancel_id
returned ENOENT after not finding the taskq it was trying to cancel.
This presumably happens when it already died for some reason; in this
case, we don't really mind it already being dead, since we're just
going to dispatch a new task to unmount it right after.
So we just ignore it if we get back ENOENT trying to cancel here,
retry a couple times if we get back the only other possible condition
(EBUSY), and log to dbgmsg if we got anything but ENOENT or success.
(We also add some locking around taskqid, to avoid one or two cases
of two instances of trying to cancel something at once.)
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#11632Closes#12670
Update the META file to reflect compatibility with the 6.4 kernel.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Lahfa <ryan@lahfa.xyz>
Closes#15125
For large JBODs the log message "zfs_iter_vdev: no match" can
account for the bulk of the log messages (over 70%). Since this
message is purely informational and not that useful we remove it.
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#15086Closes#15094
We would see zed assert on one of our systems if we powered off a
slot. Further examination showed zfs_retire_recv() was reporting
a GUID of 0, which in turn would return a NULL nvlist. Add
in a check for a zero GUID.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#15084
Unlike regular receive, raw receive require destination to have the
same block structure as the source. In case of dnode reclaim this
triggers two special cases, requiring special handling:
- If dn_nlevels == 1, we can change the ibs, but dnode_set_blksz()
should not dirty the data buffer if block size does not change, or
durign receive dbuf_dirty_lightweight() will trigger assertion.
- If dn_nlevels > 1, we just can't change the ibs, dnode_set_blksz()
would fail and receive_object would trigger assertion, so we should
destroy and recreate the dnode from scratch.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#15039
The previous code was checking zfs_is_namespace_prop() only for the
last property on the list. If one was not "namespace", then remount
wasn't called. To fix that move zfs_is_namespace_prop() inside the
loop and remount if at least one of properties was "namespace".
Reviewed-by: Umer Saleem <usaleem@ixsystems.com>
Reviewed-by: Ameer Hamza <ahamza@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#15000
With the latest L2ARC fixes, 2 seconds is too long to wait for
quiescence of arcstats like l2_size. Shorten this interval to avoid
having the persistent L2ARC tests in ZTS prematurely terminated.
Signed-off-by: George Amanakis <gamanakis@gmail.com>
If this is not done, and the pool has an ashift other than the default
(at the moment 9) then the following happens:
1) vdev_alloc() assigns the ashift of the pool to L2ARC device, but
upon export it is not stored anywhere
2) at the first import, vdev_open() sees an vdev_ashift() of 0 and
assigns the logical_ashift, which is 9
3) reading the contents of L2ARC, including the header fails
4) L2ARC buffers are not restored in ARC.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#14313Closes#14963
While commit bcd5321 adjusts the write size based on the size of the log
block, this happens after comparing the unadjusted write size to the
evicted (target) size.
In this case l2ad_hand will exceed l2ad_evict and violate an assertion
at the end of l2arc_write_buffers().
Fix this by adding the max log block size to the allocated size of the
buffer to be committed before comparing the result to the target
size.
Also reset the l2arc_trim_ahead ZFS module variable when the adjusted
write size exceeds the size of the L2ARC device.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#14936Closes#14954
l2arc_write_size() should return the write size after adjusting for trim
and overhead of the L2ARC log blocks. Also take into account the
allocated size of log blocks when deciding when to stop writing buffers
to L2ARC.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#14939
l2arc_evict() performs the adjustment of the size of buffers to be
written on L2ARC unnecessarily. l2arc_write_size() is called right
before l2arc_evict() and performs those adjustments.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#14828
482da24e2 missed arc_buf_destroy() calls on log parse errors, possibly
leaking up to 128KB of memory per dataset during ZIL replay.
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Given:
/sbin/zfs list filling/a-zvol<TAB> -o space,refratio
The rest of the cmdline gets vored by:
/sbin/zfs list filling/a-zvolcannot open 'filling/a-zvol':
operation not applicable to datasets of this type
With -x (fragment):
+ COMPREPLY=($(compgen -W "$(__zfs_match_snapshot)" -- "$cur"))
+++ __zfs_match_snapshot
+++ local base_dataset=filling/dziadtop-nowe-duchy
+++ [[ filling/dziadtop-nowe-duchy != filling/dziadtop-nowe-duchy ]]
+++ [[ filling/dziadtop-nowe-duchy != '' ]]
+++ __zfs_list_datasets filling/dziadtop-nowe-duchy
+++ /sbin/zfs list -H -o name -s name -t filesystem
-r filling/dziadtop-nowe-duchy
+++ tail -n +2
cannot open 'filling/dziadtop-nowe-duchy':
operation not applicable to datasets of this type
+++ echo filling/dziadtop-nowe-duchy
+++ echo filling/dziadtop-nowe-duchy@
++ compgen -W 'filling/dziadtop-nowe-duchy
This properly completes with:
$ /sbin/zfs list filling/a-zvol<TAB> -o space,refratio
filling/a-zvol filling/a-zvol@
$ /sbin/zfs list filling/a-zvol<cursor> -o space,refratio
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Backport-of: 5ece420f03Closes#12820
Two problems led to unexpected behaviour of the scriptlets:
1) Newer DKMS versions change the formatting of "dkms status":
(old) zfs, 2.1.2, 5.14.10-300.fc35.x86_64, x86_64: installed
(new) zfs/2.1.2, 5.14.10-300.fc35.x86_64, x86_64: installed
Which broke a conditional determining whether to uninstall.
2) zfs_config.h not packaged properly, but was attempted to be read
in the %preun scriptlet:
CONFIG_H="/var/lib/dkms/zfs/2.1.2/*/*/zfs_config.h"
Which broke the uninstallation of the module, which left behind a
dangling symlink, which broke DKMS entirely with this error:
Error! Could not locate dkms.conf file.
File: /var/lib/dkms/zfs/2.1.1/source/dkms.conf does not exist.
This change attempts to simplify life by:
* Avoiding parsing anything (less prone to future breakage)
* Uses %posttrans instead of %post for module installation, because
%post happens before %preun, while %posttrans happens afterwards
* Unconditionally reinstall module on upgrade, which is less
efficient but the trade-off is that it's more reliable
Alternative approaches could involve fixing the existing parsing bugs
or improving the logic, but this comes at the cost of complexity and
possible future bugs.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jeremy Visser <jeremyvisser@google.com>
Closes#10463Closes#13182
- Clang 15 doesn't support `-fno-ipa-sra` anymore. Do a separate
check for `-fno-ipa-sra` support by $KERNEL_CC.
- Don't enable `-mgeneral-regs-only` for certain module files.
Fix#13260
- Scope `GCC diagnostic ignored` statements to GCC only. Clang
doesn't need them to compile the code.
Porting notes:
- Moved the stanzas removing -mgeneral-regs-only to Makefile.in
since they wouldn't readily work in Kbuild.in and that did.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: szubersk <szuberskidamian@gmail.com>
Closes#13260Closes#14150Closes#14624
Ported-by: Rich Ercolani <rincebrain@gmail.com
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Update the META file to reflect compatibility with the 6.3 kernel.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Add a new union member of flexible array to dnode_phys_t and use
it in the macro so we can silence the memcpy() fortify error.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Youzhong Yang <yyang@mathworks.com>
Closes#14737
Linux kernel 6.3 changed a bunch of APIs to use the dedicated idmap
type for mounts (struct mnt_idmap), we need to detect these changes
and make zfs work with the new APIs.
NOTE: This backport only includes the configure checks to detect
the 6.3 idmap API changes. It does not include support for idmap.
When provided the idmap variable is ignored in most case in the
same way the user_ns argument was ignored. This change is solely
to provide compatibility with the new interfaces.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Youzhong Yang <yyang@mathworks.com>
Closes#14682
The type def of writepage_t in kernel 6.3 is changed to take
struct folio* as the first argument. We need to detect this
change and pass correct function to write_cache_pages().
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Youzhong Yang <yyang@mathworks.com>
Closes#14699
Linux since 4.7 makes interface 'cpu_has_feature' to use jump labels on
powerpc if CONFIG_JUMP_LABEL_FEATURE_CHECKS is enabled, in this case
however the inline function references GPL-only symbol
'cpu_feature_keys'.
ZFS currently uses 'cpu_has_feature' either directly or indirectly from
several places; while it is unknown how this issue didn't break ZFS on
64-bit little-endian powerpc, it is known to break ZFS with many Linux
versions on both 32-bit and 64-bit big-endian powerpc.
Until this issue is fixed in Linux, we have to workaround it by
overriding affected inline functions without depending on
'cpu_feature_keys'.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: WHR <msl0000023508@gmail.com>
Closes#14590
As of the 4.13 kernel filemap_range_has_page() can be used to
check if there is a page mapped in a given file range. When
available this interface should be used which eliminates the
need for the zp->z_is_mapped boolean.
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#14493
Page writebacks with WB_SYNC_NONE can take several seconds to complete
since they wait for the transaction group to close before being
committed. This is usually not a problem since the caller does not
need to wait. However, if we're simultaneously doing a writeback
with WB_SYNC_ALL (e.g via msync), the latter can block for several
seconds (up to zfs_txg_timeout) due to the active WB_SYNC_NONE
writeback since it needs to wait for the transaction to complete
and the PG_writeback bit to be cleared.
This commit deals with 2 cases:
- No page writeback is active. A WB_SYNC_ALL page writeback starts
and even completes. But when it's about to check if the PG_writeback
bit has been cleared, another writeback with WB_SYNC_NONE starts.
The sync page writeback ends up waiting for the non-sync page
writeback to complete.
- A page writeback with WB_SYNC_NONE is already active when a
WB_SYNC_ALL writeback starts. The WB_SYNC_ALL writeback ends up
waiting for the WB_SYNC_NONE writeback.
The fix works by carefully keeping track of active sync/non-sync
writebacks and committing when beneficial.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Shaan Nobee <sniper111@gmail.com>
Closes#12662Closes#12790
There seems to be no reason for ZIL blocks to be limited by 128KB
other than replay code is written in such a way. This change does
not increase the limit yet, just removes the artificial limitation.
Avoided extra memcpy() may save us a second during replay.
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
At least for RAIDZ zio_shrink() does not reduce zio size, but reduced
wsz in that case likely results in writing uninitialized memory.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14853
We only need to know if ZIO has any parent there. We do not care if
it has more than one, but use of zio_unique_parent() == NULL asserts
that.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14823
- There is no reason to assert that added gang is not empty. It
may be weird to add an empty gang, but it is legal.
- When moving chain list from the added gang clear its size, or it
will trigger assertion in abd_verify() when that gang is freed.
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14816
TX_COMMIT has no on-disk representation and does not produce any more
dirty data. It should not wait for anything, and even just skipping
the checks if not waiting gives improvement noticeable in profiler.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Prakash Surya <prakash.surya@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14798
Gang ABDs without childred are legal, and they do have zero size.
For other ABD types zero size doesn't have much sense and likely
not working correctly now.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14795
In the case of a regular compilation, the compiler
raises a warning for a dsl_deadlist_merge function, that
the stack size is to large. In debug build this can
generate an error.
Move large structures to heap.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Mariusz Zaborski <mariusz.zaborski@klarasystems.com>
Sponsored-by: Klara, Inc.
Sponsored-by: Wasabi Technology, Inc.
Closes#14524
A NULL pointer will occur when doing a 'zfs send -S' on a dataset that
is still being received. The problem is that the new 'send' will
rightfully fail to own the datasets (i.e. dsl_dataset_own_force() will
fail), but then dmu_send() will still do the dsl_dataset_disown().
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Luís Henriques <henrix@camandro.org>
Closes#14903Closes#14890
CLOCK_MONOTONIC_RAW is only a thing on Linux and macOS. I'm not
actually sure why the previous hardcoding of a constant didn't
error out, but when we removed it, it sure does now.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Rich Ercolani <rincebrain@gmail.com>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12995
It became illegal to not have them as of
5f6df177758b9dff88e4b6069aeb2359e8b0c493 ("vfs: validate that vop
vectors provide all or none fplookup vops") upstream.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#14788
Under certain loads, the following panic is hit:
panic: page fault
KDB: stack backtrace:
#0 0xffffffff805db025 at kdb_backtrace+0x65
#1 0xffffffff8058e86f at vpanic+0x17f
#2 0xffffffff8058e6e3 at panic+0x43
#3 0xffffffff808adc15 at trap_fatal+0x385
#4 0xffffffff808adc6f at trap_pfault+0x4f
#5 0xffffffff80886da8 at calltrap+0x8
#6 0xffffffff80669186 at vgonel+0x186
#7 0xffffffff80669841 at vgone+0x31
#8 0xffffffff8065806d at vfs_hash_insert+0x26d
#9 0xffffffff81a39069 at sfs_vgetx+0x149
#10 0xffffffff81a39c54 at zfsctl_snapdir_lookup+0x1e4
#11 0xffffffff8065a28c at lookup+0x45c
#12 0xffffffff806594b9 at namei+0x259
#13 0xffffffff80676a33 at kern_statat+0xf3
#14 0xffffffff8067712f at sys_fstatat+0x2f
#15 0xffffffff808ae50c at amd64_syscall+0x10c
#16 0xffffffff808876bb at fast_syscall_common+0xf8
The page fault occurs because vgonel() will call VOP_CLOSE() for active
vnodes. For this reason, define vop_close for zfsctl_ops_snapshot. While
here, define vop_open for consistency.
After adding the necessary vop, the bug progresses to the following
panic:
panic: VERIFY3(vrecycle(vp) == 1) failed (0 == 1)
cpuid = 17
KDB: stack backtrace:
#0 0xffffffff805e29c5 at kdb_backtrace+0x65
#1 0xffffffff8059620f at vpanic+0x17f
#2 0xffffffff81a27f4a at spl_panic+0x3a
#3 0xffffffff81a3a4d0 at zfsctl_snapshot_inactive+0x40
#4 0xffffffff8066fdee at vinactivef+0xde
#5 0xffffffff80670b8a at vgonel+0x1ea
#6 0xffffffff806711e1 at vgone+0x31
#7 0xffffffff8065fa0d at vfs_hash_insert+0x26d
#8 0xffffffff81a39069 at sfs_vgetx+0x149
#9 0xffffffff81a39c54 at zfsctl_snapdir_lookup+0x1e4
#10 0xffffffff80661c2c at lookup+0x45c
#11 0xffffffff80660e59 at namei+0x259
#12 0xffffffff8067e3d3 at kern_statat+0xf3
#13 0xffffffff8067eacf at sys_fstatat+0x2f
#14 0xffffffff808b5ecc at amd64_syscall+0x10c
#15 0xffffffff8088f07b at fast_syscall_common+0xf8
This is caused by a race condition that can occur when allocating a new
vnode and adding that vnode to the vfs hash. If the newly created vnode
loses the race when being inserted into the vfs hash, it will not be
recycled as its usecount is greater than zero, hitting the above
assertion.
Fix this by dropping the assertion.
FreeBSD-issue: https://bugs.freebsd.org/bugzilla/show_bug.cgi?id=252700
Reviewed-by: Andriy Gapon <avg@FreeBSD.org>
Reviewed-by: Mateusz Guzik <mjguzik@gmail.com>
Reviewed-by: Alek Pinchuk <apinchuk@axcient.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Rob Wing <rob.wing@klarasystems.com>
Co-authored-by: Rob Wing <rob.wing@klarasystems.com>
Submitted-by: Klara, Inc.
Sponsored-by: rsync.net
Closes#14501
Noticed while attempting to change FreeBSD's boolean_t into an actual
bool: in include/sys/zfs_ioctl_impl.h, zfs_vfs_held() is declared to
return a boolean_t, but in module/os/freebsd/zfs/zfs_ioctl_os.c it is
defined to return an int. Make the definition match the declaration.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Dimitry Andric <dimitry@andric.com>
Closes#14776
When the special_small_blocks property is being set during a pool
create it enforces a limit of 128KiB even if the pool's record size
is larger.
If the recordsize property is being set during a pool create, then
use that value instead of the default SPA_OLD_MAXBLOCKSIZE value.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <dev.fs.zfs@gmail.com>
Closes#13815Closes#14811
The zpool_resilver_concurrent test case requires the ZED which is not used
on FreeBSD. Add this test to the known list of skipped tested for FreeBSD.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#14904
The auto_replace_001_pos test case does not reliably pass on
Fedora 37 and newer. Until the test case can be updated to make
it reliable add it to the list of "maybe" exceptions on Linux.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #14851Closes#14852
Add snapshot_002_pos to the known list of occasional failures
for FreeBSD until it can be made entirely reliable.
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #14831Closes#14832
We use block_device_wait to wait for the zvol block device to
actually appear, and we log the result of the dd calls by using
an intermediate file.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: John Wren Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#14767
When a vdev is degraded or faulted, we refuse to expand it when doing
online -e. However, we also don't actually cause the online command
to fail, even though the disk didn't expand. This is confusing and
misleading, and can result in violated expectations.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes 14145
The kmem allocation in zfs_prune_aliases() will trigger a large
allocation warning on systems with 64K pages. Resolve this by
switching to vmem_alloc() which internally uses kvmalloc() so the
right allocator will be used based on the allocation size.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8491Closes#14694
zpool initialize functions well for touching every free byte...once.
But if we want to do it again, we're currently out of luck.
So let's add zpool initialize -u to clear it.
Co-authored-by: Rich Ercolani <rincebrain@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12451Closes#14873
Before allowing the ZED to mark a vdev as REMOVED due to a
hotplug event confirm that it is non-responsive with probe.
Any device which can be successfully probed should be left
ONLINE to prevent a healthy pool from being incorrectly
SUSPENDED. This may occur for at least the following two
scenarios.
1) Drive expansion (zpool online -e) in VMware environments.
If, during the partition resize operation, a partition is
removed and re-created then udev will send a removed event.
2) Re-scanning the namespaces of an NVMe device (nvme ns-rescan)
may result in a udev remove and add event being delivered.
Finally, update the ZED to only kick in a spare when the
removal was successful.
Reviewed-by: Ameer Hamza <ahamza@ixsystems.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #14859Closes#14861
For draid vdevs it was possible to initiate both the
sequential and healing resilver at same time.
This fixes the following two scenarios.
1) There's a window where a sequential rebuild can
be started via ZED even if a healing resilver has been
scheduled.
- This is fixed by adding additional check in
spa_vdev_attach() for any scheduled resilver and return
appropriate error code when a resilver is already in
progress.
2) It was possible for zpool clear to start a healing
resilver when it wasn't needed at all. This occurs because
during a vdev_open() the device is presumed to be healthy not
until the device is validated by vdev_validate() and it's set
unavailable. However, by this point an async resilver will
have already been requested if the DTL isn't empty.
- This is fixed by cancelling the SPA_ASYNC_RESILVER
request immediately at the end of vdev_reopen() when a resilver
is unneeded.
Finally, added a testcase in ZTS for verification.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Dipak Ghosh <dipak.ghosh@hpe.com>
Signed-off-by: Akash B <akash-b@hpe.com>
Closes#14881Closes#14892
When using zdb to output the value of an xattr only interpret it
as printable characters if the entire byte array is printable.
Additionally, if the --parseable option is set always output the
buffer contents as octal for easy parsing.
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#14830
Provides an interface which callers can use to declare a write when
the exact starting offset in not yet known. Since the full range
being updated is not available only the first L0 block at the
provided offset will be prefetched.
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#14819
The pam ZTS tests were reporting a buffer overflow on F38, possibly
due to F38 now setting _FORTIFY_SOURCE=3 by default. gdb and
valgrind narrowed this down to a snprintf() buffer overflow in
zfs_key_config_modify_session_counter(). I'm not clear why this
particular snprintf() was being flagged as an overflow, but when
I replaced it with an asprintf(), the test passed reliably.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#14802Closes#14842
If we receive a DRR_FREEOBJECTS as the first entry in an object range,
this might end up producing a hole if the freed objects were the
only existing objects in the block.
If the txg starts syncing before we've processed any following
DRR_OBJECT records, this leads to a possible race where the backing
arc_buf_t gets its psize set to 0 in the arc_write_ready() callback
while still being referenced from a dirty record in the open txg.
To prevent this, we insert a txg_wait_synced call if the first
record in the range was a DRR_FREEOBJECTS that actually
resulted in one or more freed objects.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: David Hedberg <david.hedberg@findity.com>
Sponsored by: Findity AB
Closes#11893Closes#14358
spa_import() relies on a pool config fetched by spa_try_import() for
spare/cache devices. Import flags are not passed to spa_tryimport(),
which makes it return early due to a missing log device and missing
retrieving the cache device and spare eventually. Passing
ZFS_IMPORT_MISSING_LOG to spa_tryimport() makes it fetch the correct
configuration regardless of the missing log device.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#14794
At our site we have seen cases when multi-modifier protection is enabled
(multihost=on) on our pool and the pool gets suspended due to a single
disk that is failing and responding very slowly. Our pools have 90 disks
in them and we expect disks to fail. The current version of MMP requires
that we wait for other writers before moving on. When a disk is
responding very slowly, we observed that waiting here was bad enough to
cause the pool to suspend. This change allows the MMP thread to bypass
waiting for other threads and reduces the chances the pool gets
suspended.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Herb Wartens <hawartens@gmail.com>
Closes#14659
When testing distributed rebuild performance with more capable
hardware it was observed than increasing the zfs_rebuild_vdev_limit
to 64M reduced the rebuild time by 17%. Beyond 64MB there was
some improvement (~2%) but it was not significant when weighed
against the increased memory usage. Memory usage is capped at 1/4
of arc_c_max.
Additionally, vr_bytes_inflight_max has been moved so it's updated
per-metaslab to allow the size to be adjust while a rebuild is
running.
Reviewed-by: Akash B <akash-b@hpe.com>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#14428
For HDD based pools the default zfs_scan_vdev_limit of 4M
per-vdev can significantly limit the maximum scrub performance.
Increasing the default to 16M can double the scrub speed from
80 MB/s per disk to 160 MB/s per disk.
This does increase the memory footprint during scrub/resilver
but given the performance win this is a reasonable trade off.
Memory usage is capped at 1/4 of arc_c_max. Note that number
of outstanding I/Os has not changed and is still limited by
zfs_vdev_scrub_max_active.
Reviewed-by: Akash B <akash-b@hpe.com>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#14428
When resilvering the estimated time remaining is calculated using
the average issue rate over the current pass. Where the current
pass starts when a scan was started, or restarted, if the pool
was exported/imported.
For dRAID pools in particular this can result in wildly optimistic
estimates since the issue rate will be very high while scanning
when non-degraded regions of the pool are scanned. Once repair
I/O starts being issued performance drops to a realistic number
but the estimated performance is still significantly skewed.
To address this we redefine a pass such that it starts after a
scanning phase completes so the issue rate is more reflective of
recent performance. Additionally, the zfs_scan_report_txgs
module option can be set to reset the pass statistics more often.
Reviewed-by: Akash B <akash-b@hpe.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#14410
Spare vdev should detach from the pool when a disk is reinserted.
However, spare detachment depends on the completion of resilvering,
and if resilver does not schedule, the spare vdev keeps attached to
the pool until the next resilvering. When a zfs pool contains
several disks (25+ mirror), resilvering does not always happen when
a disk is reinserted. In this patch, spare vdev is manually detached
from the pool when resilvering does not occur and it has been tested
on both Linux and FreeBSD.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#14722
After 89cd2197b9 was merged, Clang's
static analyzer began complaining about a dead assignment in
`zfs_fillpage()`. Upon inspection, I noticed that the dead assignment
was because we are not using the calculated io_len that we should use to
avoid asking the DMU to read past the end of a file. This should result
in `dmu_buf_hold_array_by_dnode()` calling `zfs_panic_recover()`.
This issue predates 89cd2197b9, but its
simplification of zfs_fillpage() eliminated the only use of the
assignment to io_len, which made Clang's static analyzer complain about
the issue.
Also, as a precaution, we add an assertion that io_offset < i_size. If
this ever fails, bad things will happen. Otherwise, we are blindly
trusting the kernel not to give us invalid offsets. We continue to
blindly trust it on non-debug kernels.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14534
When a page is faulted in for memory mapped I/O the page lock
may be dropped before it has been read and marked up to date.
If a buffered read encounters such a page in mappedread() it
must wait until the page has been updated. Failure to do so
will result in a panic on debug builds and incorrect data on
production builds.
The critical part of this change is in mappedread() where pages
which are not up to date are now handled. Additionally, it
includes the following simplifications.
- zfs_getpage() and zfs_fillpage() could be passed an array of
pages. This could be more efficient if it was used but in
practice only a single page was ever provided. These
interfaces were simplified to acknowledge that.
- update_pages() was modified to correctly set the PG_error bit
on a page when it cannot be read by dmu_read().
- Setting PG_error and PG_uptodate was moved to zfs_fillpage()
from zpl_readpage_common(). This is consistent with the
handling in update_pages() and mappedread().
- Minor additional refactoring to comments and variable
declarations to improve readability.
- Add a test case to exercise concurrent buffered, direct,
and mmap IO to the same file.
- Reduce the mmap_sync test case default run time.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13608Closes#14498
This had always worked in my testing, but a user on hardware reported
this to happen 100%, and I reproduced it once with cold VM host caches.
dracut-zfs-generator runs as a systemd generator, i.e. at Some
Relatively Early Time; if root= is a fixed dataset, it tries to
"solve [necessities] statically at generation time".
If by that point zfs-import.target hasn't popped (because the import is
taking a non-negligible amount of time for whatever reason), it'll see
no children for the root datase, and as such generate no mounts.
This has never had any right to work. No-one caught this earlier because
it's just that much more convenient to have root=zfs:AUTO, which orders
itself properly.
To fix this, always run zfs-nonroot-necessities.service;
this additionally simplifies the implementation by:
* making BOOTFS from zfs-env-bootfs.service be the real, canonical,
root dataset name, not just "whatever the first bootfs is",
and only set it if we're ZFS-booting
* zfs-{rollback,snapshot}-bootfs.service can use this instead of
re-implementing it
* having zfs-env-bootfs.service also set BOOTFSFLAGS
* this means the sysroot.mount drop-in can be fixed text
* zfs-nonroot-necessities.service can also be constant and always
enabled, because it's conditioned on BOOTFS being set
There is no longer any code generated at run-time
(the sysroot.mount drop-in is an unavoidable gratuitous cp).
The flow of BOOTFS{,FLAGS} from zfs-env-bootfs.service to sysroot.mount
is not noted explicitly in dracut.zfs(7), because (a) at some point it's
just visual noise and (b) it's already ordered via d-p-m.s from z-i.t.
Backport-of: 3399a30ee0
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Deprecation of Python versions below 3.6 gives opportunity to unify the
build and install requirements for OpenZFS packages. The minimal
supported Python version is 3.6 as this is the most recent Python
package CentOS/RHEL 7 users can get.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Rich Ercolani <rincebrain@gmail.com>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: szubersk <szuberskidamian@gmail.com>
Closes#12925
Modify bio_set_flush() so if kernel version is >= 4.10, flags
REQ_PREFLUSH and REQ_OP_WRITE are set together.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Youzhong Yang <yyang@mathworks.com>
Closes#14695
Running `zfs list -o avail rpool` resulted in a core dump.
This commit will fix this.
Run the needed overhead only, when `use_color()` is true.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Wilson <gwilson@delphix.com>
Signed-off-by: Tino Reichardt <milky-zfs@mcmilk.de>
Closes#14712
Add a -K option to the test suite to log each test name to /dev/kmsg
(on Linux), so if there's a kernel warning we'll be able to match
it up to a particular test.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes #13227
- Kmemleak `clear` is invoked right before every test case run.
- Kmemleak `scan` is requested right after each test case is finished.
- Kmemleak instrumentation is not used for
setup/cleanup/pretest/posttest/failsafe stages to shorten the test
case execution time.
- Kmemleak periodic scan is disabled (`scan=0`) before the test suite
run to avoid interfering with the on-demand scan results.
- There are unavoidable potential false positives coming from kernel
areas other than OpenZFS module.
- The ZTS with kmemleak enabled duration is increased by ~50%.
Example run
```
Running Time: 07:12:13
Percent passed: 98.3%
unreferenced object 0xffff9da82aea5410 (size 80):
comm "kworker/u32:10", pid 942206, jiffies 4296749716 (age 2615.516s)
hex dump (first 32 bytes):
00 30 30 00 00 00 00 00 ff 8f 30 00 00 00 00 00 .00.......0.....
51 e6 77 05 a8 9d ff ff 00 00 00 00 00 00 00 00 Q.w.............
backtrace:
[<000000005cf1fea2>] alloc_extent_state+0x1d/0xb0 [btrfs]
[<0000000083f78ae5>] set_extent_bit+0x2ff/0x670 [btrfs]
[<00000000de29249e>] lock_extent_bits+0x6b/0xa0 [btrfs]
[<00000000b241f424>] lock_and_cleanup_extent_if_need+0xaf/0x1c0
[btrfs]
[<0000000093ca72b5>] btrfs_buffered_write+0x297/0x7d0 [btrfs]
[<000000002c2938c8>] btrfs_file_write_iter+0x127/0x390 [btrfs]
[<00000000b888f720>] do_iter_readv_writev+0x152/0x1b0
[<00000000320f0bcc>] do_iter_write+0x7c/0x1c0
[<000000000b5a8fe0>] lo_write_bvec+0x62/0x150 [loop]
[<000000009aa03c73>] loop_process_work+0x250/0xbd0 [loop]
[<00000000c7487d8a>] process_one_work+0x1f1/0x390
[<000000000b236831>] worker_thread+0x53/0x3e0
[<0000000023cb3e57>] kthread+0x127/0x150
[<000000002d48676a>] ret_from_fork+0x22/0x30
```
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: szubersk <szuberskidamian@gmail.com>
Closes#13084
Update the META file to reflect compatibility with the 6.2 kernel.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#14689
After commit 19d3961, progress reporting (-v) with replication flag
enabled does not report the progress on the console. This commit
fixes the issue by updating the logic to check for pa->progress
instead of pa_verbosity in send_progress_thread().
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#14448
This allows parsing of zfs send progress by checking the process
title.
Doing so requires some changes to the send code in libzfs_sendrecv.c;
primarily these changes move some of the accounting around, to allow
for the code to be verbose as normal, or set the process title. Unlike
BSD, setproctitle() isn't standard in Linux; thus, borrowed it from
libbsd with slight modifications.
Authored-by: Sean Eric Fagan <sef@FreeBSD.org>
Co-authored-by: Ryan Moeller <ryan@iXsystems.com>
Co-authored-by: Ameer Hamza <ahamza@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#14376
Holding the zp->z_rangelock as a RL_READER over the range
0-UINT64_MAX is sufficient to prevent the dnode from being
re-dirtied by concurrent writers. To avoid potentially
looping multiple times for external caller which do not
take the rangelock holes are not reported after the first
sync. While not optimal this is always functionally correct.
This change adds the missing rangelock calls on FreeBSD to
zvol_cdev_ioctl().
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#14512Closes#14641
Use a bold header row and colorize the AVAIL column based on
the used space percentage of volume.
We define these colors:
- when > 80%, use yellow
- when > 90%, use red
Reviewed-by: WHR <msl0000023508@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ethan Coe-Renner <coerenner1@llnl.gov>
Signed-off-by: Tino Reichardt <milky-zfs@mcmilk.de>
Closes#14621Closes#14350
Use a bold header and colorize the space suffixes in iostat
by order of magnitude like this:
- K is green
- M is yellow
- G is red
- T is lightblue
- P is magenta
- E is cyan
- 0 space is colored gray
Reviewed-by: WHR <msl0000023508@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ethan Coe-Renner <coerenner1@llnl.gov>
Signed-off-by: Tino Reichardt <milky-zfs@mcmilk.de>
Closes#14621Closes#14459
Linux 6.3+, and backports from it (6.2.8+), changed the
signatures on bdev_io_{start,end}_acct. Add a case for it.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#14658Closes#14668
zfsd fetches new pool configuration through ZFS_IOC_POOL_STATS but
it does not get updated nvlist configuration for spare vdev since
the configuration is read by spa_spares->sav_config. In this commit,
updating the vdev state for spare vdev that is consumed by zfsd on
spare disk hotplug.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#14653
This commit supports for spare vdev hotplug. The
spare vdev associated with all the pools will be
marked as "Removed" when the drive is physically
detached and will become "Available" when the
drive is reattached. Currently, the spare vdev
status does not change on the drive removal and
the same is the case with reattachment.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#14295
In order for zed to process the removal event correctly,
udev change event needs to be posted to sync the blkid
information. spa_create() and spa_config_update() posts
the event already through spa_write_cachefile(). Doing
the same for spa_vdev_attach() that handles the case
for vdev attachment and replacement.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#14172
ZED does not take any action for disk removal events if there is no
spare VDEV available. Added zpool_vdev_remove_wanted() in libzfs
and vdev_remove_wanted() in vdev.c to remove the VDEV through ZED
on removal event. This means that if you are running zed and
remove a disk, it will be propertly marked as REMOVED.
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Remove arc_reduce_target_size() call from arc_prune_task(). The idea
of arc_prune_task() is to remove external references on ARC metadata,
such as vnodes. Since arc_prune_async() is called only from ARC itself,
it makes no sense to create a parasitic loop between ARC eviction and
the pruning, treatening to drop ARC to its minimum. I can't guess why
it was added as part of FreeBSD to OpenZFS integration.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14639
Debugging reported NULL de-reference panic in dnode_hold_impl() I found
that for certain types of errors arc_read() may only return error code,
but not properly report it via done and pio arguments. Lack of done
calls may result in reference and/or memory leaks in higher level code.
Lack of error reporting via pio may result in unnoticed errors there.
For example, dbuf_read(), where dbuf_read_impl() ignores arc_read()
return, relies completely on the pio mechanism and missed the errors.
This patch makes arc_read() to always call done callback and always
propagate errors to parent zio, if either is provided.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
CpaDcRqResults have to be initialized with checksum=1 for adler32.
Otherwise when error CPA_DC_OVERFLOW occurred, the next compress
operation will continue on previously part-compressed data, and write
invalid checksum data. When zfs decompress the compressed data, a
invalid checksum will occurred and lead to #14463
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Weigang Li <weigang.li@intel.com>
Reviewed-by: Chengfei Zhu <chengfeix.zhu@intel.com>
Signed-off-by: naivekun <naivekun0817@gmail.com>
Closes#14632Closes#14463
`lseek(SEEK_DATA | SEEK_HOLE)` are only accurate when the on-disk blocks
reflect all writes, i.e. when there are no dirty data blocks. To ensure
this, if the target dnode is dirty, they wait for the open txg to be
synced, so we can call them "stabilizing operations". If they cause
txg_wait_synced often, it can be detrimental to performance.
Typically, a group of files are all modified, and then SEEK_DATA/HOLE
are performed on them. In this case, the first SEEK does a
txg_wait_synced(), and subsequent SEEKs don't need to wait, so
performance is good.
However, if a workload involves an interleaved metadata modification,
the subsequent SEEK may do a txg_wait_synced() unnecessarily. For
example, if we do a `read()` syscall to each file before we do its SEEK.
This applies even with `relatime=on`, when the `read()` is the first
read after the last write. The txg_wait_synced() is unnecessary because
the SEEK operations only care that the structure of the tree of indirect
and data blocks is up to date on disk. They don't care about metadata
like the contents of the bonus or spill blocks. (They also don't care
if an existing data block is modified, but this would be more involved
to filter out.)
This commit changes the behavior of SEEK_DATA/HOLE operations such that
they do not call txg_wait_synced() if there is only a pending change to
the bonus or spill block.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#13368
Issue #14594
Issue #14512
Issue #14009
Update the GitHub actions workflows using a subset of the changes
from the master branch, commit 620a977f22. Cherry-picking each
relevant commit would have resulted in a large number of conflicts
so this change only applies a minimal set of useful updates.
- Added build-dependencies.txt and checkstyle-dependencies.txt
- Added reclaim_disk_space.sh script
- Minor changes to build steps
- Reduced ztest run time
- checkbashisms, mandoc, and cppcheck were not included to
avoid additional backports
- Add exceptions for shellcheck
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
- GitHub workflows are run on Ubuntu 22.04
- Extract the `checkstyle` workflow dependencies to a separate file.
- Refresh the `build-dependencies.txt` list.
Notes: Partial check pick of 9e7fc5da38. This change does not
include the build-dependencies.txt or checkstyle-dependencies.txt
changes.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: szubersk <szuberskidamian@gmail.com>
Closes#14148
When using the zfs initramfs scripts on my system, I get various
errors at initramfs stage, such as:
cannot open '-o': name must begin with a letter
My zfs binaries are compiled with musl libc, which may be why
this happens. In any case, fix the argument order to make the
zpool binary happy, and to match its --help output.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Daniel Kolesa <daniel@octaforge.org>
Closes#14572
The default_bs and default_ibs tunables control the default block size
and indirect block size.
So far, default_bs and default_ibs were tunable only on FreeBSD, e.g.,
sysctl vfs.zfs.default_ibs
Remove the FreeBSD-specific sysctl code and expose default_bs and
default_ibs as tunables on both Linux and FreeBSD using
ZFS_MODULE_PARAM.
One of the use cases for changing the values of those tunables is to
lower the indirect block size, which may improve performance of large
directories (as discussed during the OpenZFS Leadership Meeting
on 2022-08-16).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Mateusz Piotrowski <mateusz.piotrowski@klarasystems.com>
Sponsored-by: Wasabi Technology, Inc.
Closes#14293
dc5c8006f6 was recently merged to prefetch
up to 128 deadlists. Unfortunately, a loop was missing an increment,
such that it will prefetch all deadlists. The performance properties of
that patch probably should be re-evaluated.
This was caught by CodeQL's cpp/constant-comparison check in an
experimental branch where I am testing the security-and-extended
queries. It complained about the `i < 128` part of the loop condition
always evaluating to the same thing. The standard CodeQL configuration
we use missed this because it does not include that check.
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14573
by placing the most common use case (no special vdevs) first and avoid
allocating new variables.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#14494Closes#14563
With some pathological access patterns it is possible to make ZFS
accumulate almost unlimited amount of speculative prefetch ZIOs.
Combined with linear ABD allocations in RAIDZ code, it appears to
be possible to exhaust system KVA, triggering kernel panic.
Address this by introducing a system-wide counter of active prefetch
requests and blocking prefetch distance doubling per stream hits if
the number of active requests is higher that ~6% of ARC size.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14516
During snapshot deletion ZFS may issue several reads for each deadlist
to merge them into next snapshot's or pool's bpobj. Number of the dead
lists increases with number of snapshots. On HDD pools it may take
significant time during which sync thread is blocked.
This patch introduces prescient prefetch of required blocks for up to
128 deadlists ahead. Tests show reduction of time required to delete
dataset with 720 snapshots with randomly overwritten file on wide HDD
pool from 75-85 to 22-28 seconds.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Issue #14276Closes#14402
Despite all optimizations, tests on actual hardware show that FreeBSD
kernel can't sleep for less then ~2us. Similar tests on Linux show
~50us delay at least from nanosleep() (haven't tested inside kernel).
It means that on very fast log device ZIL may not be able to satisfy
zfs_commit_timeout_pct block commit timeout, increasing log latency
more than desired.
Handle that by introduction of zil_min_commit_timeout parameter,
specifying minimal timeout value where additional delays to aggregate
writes may be skipped. Also skip delays if the LWB is more than 7/8
full, that often happens if I/O sizes are constant and match one of
LWB sizes. Both things are applied only if there were no already
outstanding log blocks, that may indicate single-threaded workload,
that by definition can not benefit from the commit delays.
While there, add short time moving average to zl_last_lwb_latency to
make it more stable.
Tests of single-threaded 4KB writes to NVDIMM SLOG on FreeBSD show IOPS
increase by 9% instead of expected 5%. For zfs_commit_timeout_pct of
1 there IOPS increase by 5.5% instead of expected 1%.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Prakash Surya <prakash.surya@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14418
On FreeBSD this reduces this structure size from 64 to 56 bytes.
dnode_handle_t respectively reduces from 72 to 64 bytes. It sounds
like a waste to need 72 bytes to be able to relocate 808 bytes of
dnode_t, which relocation on FreeBSD is not even supported.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14317
Microzap on-disk format does not include a hash tree, expecting one to
be built in RAM during mzap_open(). The built tree is linked to DMU
user buffer, freed when original DMU buffer is dropped from cache. I've
found that workloads accessing many large directories and having active
eviction from DMU cache spend significant amount of time building and
then destroying the trees. I've also found that for each 64 byte mzap
element additional 64 byte tree element is allocated, that is a waste
of memory and CPU caches.
Improve memory efficiency of the hash tree by switching from AVL-tree
to B-tree. It allows to save 24 bytes per element just on pointers.
Save 32 bits on mze_hash by storing only upper 32 bits since lower 32
bits are always zero for microzaps. Save 16 bits on mze_chunkid, since
microzap can never have so many elements. Respectively with the 16 bits
there can be no more than 16 bits of collision differentiators. As
result, struct mzap_ent now drops from 48 (rounded to 64) to 8 bytes.
Tune B-trees for small data. Reduce BTREE_CORE_ELEMS from 128 to 126
to allow struct zfs_btree_core in case of 8 byte elements to pack into
2KB instead of 4KB. Aside of the microzaps it should also help 32bit
range trees. Allow custom B-tree leaf size to reduce memmove() time.
Split zap_name_alloc() into zap_name_alloc() and zap_name_init_str().
It allows to not waste time allocating/freeing memory when processing
multiple names in a loop during mzap_open().
Together on a pool with 10K directories of 1800 files each and DMU
cache limited to 128MB this reduces time of `find . -name zzz` by 41%
from 7.63s to 4.47s, and saves additional ~30% of CPU time on the DMU
cache reclamation.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14039
(cherry picked from commit 9dcdee7889)
Add config support for openEuler, so that it set the right sysconfig
dir for openEuler.
And DEFAULT_INIT_SCRIPT is no longer needed since commit "2a34db1bd
Base init scripts for SYSV systems".
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Xinliang Liu <xinliang.liu@linaro.org>
Closes#14241
Gentoo and Alpine always set the rc init scripts' shebang to
#!/sbin/openrc-run, whether or not openrc is installed.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Peter Levine <plevine457@gmail.com>
Closes#12683Closes#12692
OpenEuler uses the same package manager DNF as RHEL/Fedora. And
it is similar to RHEL/Fedora.
OpenEuler Linux is becoming the mainstream Linux distro in China.
So adding support for it makes sense for the users. For more
details about it see: https://www.openeuler.org/en/.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Damian Szuberski <szuberskidamian@gmail.com>
Signed-off-by: Xinliang Liu <xinliang.liu@linaro.org>
Closes#14222
Conflicts:
rpm/generic/zfs.spec.in
The zio returned from arc_write() in dmu_objset_sync() uses
zio_nowait(). However we may reach the end of dsl_dataset_sync()
which checks if we need to activate features in the filesystem
without knowing if that zio has even run through the ZIO pipeline yet.
In that case we will flag features to be activated in
dsl_dataset_block_born() but dsl_dataset_sync() has already
completed its run and those features will not actually be activated.
Mitigate this by moving the feature activation code in
dsl_dataset_sync_done(). Also add new ASSERTs in
dsl_scan_visitbp() checking if a block contradicts any filesystem
flags.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#13816
In initramfs, mount.zfs fails to mount a dataset with mountpoint=none,
but mount.zfs -o zfsutil works. Use -o zfsutil when mountpoint=none.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#14455
(cherry picked from commit eb823cbc76)
When mounting the root filesystem, vfs_t->mnt_vnodecovered is null
This will cause zfsctl_is_node() to dereference a null pointer when
mounting, or updating the mount flags, on the root filesystem, both
of which happen during the boot process.
Reported-by: Martin Matuska <mm@FreeBSD.org>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Closes#14218
Rather than doing a terrible credential swapping hack, we just
check that the thing being mounted is a snapshot, and the mountpoint
is the zfsctl directory, then we allow it.
If the mount attempt is from inside a jail, on an unjailed dataset
(mounted from the host, not by the jail), the ability to mount the
snapshot is controlled by a new per-jail parameter: zfs.mount_snapshot
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Sponsored-by: Modirum MDPay
Sponsored-by: Klara Inc.
Closes#13758
Linux 6.2 changes the second argument of the set_acl operation to be a
"struct dentry *" rather than a "struct inode *". The inode* parameter
is still available as dentry->d_inode, so adjust the call to the _impl
function call to dereference and pass that pointer to it.
Also document that the get_acl -> get_inode_acl member name change from
commit 884a693 was an API change also introduced in Linux 6.2.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#14415
d_alias may need to be converted to du.d_alias
depending on the kernel version.
d_alias is currently in only one place in the code which
changes
"hlist_for_each_entry(dentry, &inode->i_dentry, d_alias)"
to
"hlist_for_each_entry(dentry, &inode->i_dentry, d_u.d_alias)"
as neccesary.
This effectively results in a double macro expansion
for code that uses the zfs headers but already has its
own macro for just d_alias (lustre in this case).
Remove the conditional code for hlist_for_each_entry
and have a macro for "d_alias -> du.d_alias" instead.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Gian-Carlo DeFazio <defazio1@llnl.gov>
Closes#14377
There is an external assembly declaration extension in GNU C that glibc
uses when building with ieee128 floating point support on ppc64le.
Marking that as volatile makes no sense, so the build breaks.
It does not make sense to only mark this as volatile on Linux, since if
do not want the compiler reordering things on Linux, we do not want the
compiler reordering things on any other platform, so we stop treating
Linux specially and just manually inline the CPP macro so that we can
eliminate it. This should fix the build on ppc64le.
Tested-by: @gyakovlev
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14308Closes#14384
If a user that uses systemd and dracut wants to overide certain
settings, they typically use `systemctl edit [unit]` or place a file in
`/etc/systemd/system/[unit].d/override.conf` directly.
The zfs-dracut module did not include those overrides however, so this
did not have any effect at boot time.
For zfs-import-scan.service and zfs-import-cache.service, overrides are
now included in the dracut initramfs image.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Vince van Oosten <techhazard@codeforyouand.me>
Closes#14075Closes#14076
Authored by: Dan McDonald <danmcd@mnx.io>
Reviewed by: Patrick Mooney <pmooney@pfmooney.com>
Reviewed by: Richard Lowe <richlowe@richlowe.net>
Approved by: Joshua M. Clulow <josh@sysmgr.org>
Ported-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Illumos-issue: https://www.illumos.org/issues/15286
Illumos-commit: https://github.com/illumos/illumos-gate/commit/f137b22e734e85642da3e56e8b94da3f5f027c73
Porting Notes:
The patch in illumos did not have much of a commit message, and did not
provide attribution to the reporter, while original patch proposed to
OpenZFS did, so I am listing the reporter (myself) and original patch
author (also myself) below while including the original commit message
with some minor corrections as part of the porting notes:
In do_composition(), we have:
size = u8_number_of_bytes[*p];
if (size <= 1 || (p + size) > oslast)
break;
There, we have type promotion from int8_t to size_t, which is unsigned.
C will sign extend the value as part of the widening before treating the
value as unsigned and the negative values we can counter are error
values from U8_ILLEGAL_CHAR and U8_OUT_OF_RANGE_CHAR, which are -1 and
-2 respectively. The unsigned versions of these under two's complement
are SIZE_MAX and SIZE_MAX-1 respectively.
The bounds check is written under the assumption that `size <= 1` does a
signed comparison. This is followed by a pointer comparison to see if
the string has the correct length, which is fine.
A little further down we have:
for (i = 0; i < size; i++)
tc[i] = *p++;
When an error condition is encountered, this will attempt to iterate at
least SIZE_MAX-1 times, which will massively overflow the buffer, which
is not fine.
The kernel will kill the loop as soon as it hits the kernel stack guard
on Linux systems built with CONFIG_VMAP_STACK=y, which should be just
about all of them. That prevents arbitrary code execution and just about
any other bad thing that a black hat attacker might attempt with
knowledge of this buffer overflow. Other systems' kernels have
mitigations for unbounded in-kernel buffer overflows that will catch
this too.
Also, the patch in illumos-gate made an effort to fix C style issues
that had been fixed in the OpenZFS/ZFSOnLinux repository. Those issues
had been mentioned in the email that I originally sent them about this
issue. One of the fixes had not been already done, so it is included.
Another to collect_a_seq()'s arguments was handled differently in
OpenZFS. For the sake of avoiding unnecessary differences, it has been
adopted. This has the interesting effect that if you correct the paths
in the illumos-gate patch to match the current OpenZFS repository, you
can reverse apply it cleanly.
Original-patch-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reported-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Co-authored-by: Dan McDonald <danmcd@mnx.io>
Closes#14318Closes#14342
The 22.0 release of the python `packaging` package removed the
`LegacyVersion` trait, causing ZFS to no longer compile.
This commit replaces the sections of `ax_python_dev.m4` that rely on
`LegacyVersion` with updated implementations from the upstream
`autoconf-archive`.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#14297
- Update the link to the OpenZFS Code of Conduct.
- Remove extra "the" from contrib/initramfs/scripts/zfs
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#14298Closes#14307
This adds support to color zfs diff (in the style of git diff)
conditional on the ZFS_COLOR environment variable.
Signed-off-by: Ethan Coe-Renner <coerenner1@llnl.gov>
Outgoing mails for ZFS pool events include the pool GUID,
but not the actual pool name. Let's change this for better
readability, as it is already done in the mails for finished
pool resilvers.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Marcel Menzel <mail@mcl.gg>
Closes#14272
When inside a jail, visibility on datasets not "jailed" to the
jail is restricted. However, it was possible to enumerate all
datasets in the pool by looking at the kstats sysctl MIB.
Only the kstats corresponding to datasets that the user has
visibility on are accessible now.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Closes#14254
If the bp is NULL, we have a hole. However, when we build with
assertions, we will dereference bp when `blkid == DMU_SPILL_BLKID`. When
this happens on a hole, we will have a NULL pointer dereference.
Reported-by: Coverity (CID-1524670)
Reviewed-by: Damian Szuberski <szuberskidamian@gmail.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14264
The ZPOOL_SCRIPTS_PATH environment variable can be passed here. This
allows for arbitrarily long strings to be passed to sprintf(), which can
overflow the buffer.
I missed this in my earlier audit of the codebase. CodeQL's
cpp/unbounded-write check caught this.
Reviewed-by: Damian Szuberski <szuberskidamian@gmail.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14264
I read the following article and noticed a couple of ZFS bugs mentioned:
https://pvs-studio.com/en/blog/posts/cpp/0377/
I decided to search for them in the modern OpenZFS codebase and then
found one that matched the description of the first one:
V593 Consider reviewing the expression of the 'A = B != C' kind. The
expression is calculated as following: 'A = (B != C)'. zfs_vfsops.c 498
The consequence of this is that the error value is replaced with `1`
when there is an error. When there is no error, 0 is correctly passed.
This is a very minor issue that is unlikely to cause any real problems.
The incorrect error code would either be returned to the mount command
on a failure or any of `zfs receive`, `zfs recv`, `zfs rollback` or `zfs
upgrade`.
The second one has already been fixed.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Damian Szuberski <szuberskidamian@gmail.com>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14261
Encrypted blocks can have up to 2 DVA's, as the third DVA is reserved
for the salt+IV. However, dmu_write_policy() allows non-encrypted
blocks (e.g. DMU_OT_OBJSET) inside encrypted datasets to request and
allocate 3 DVA's, since they don't need a salt+IV (they are merely
authenicated).
However, if such a block becomes a gang block, the gang code incorrectly
limits the gang block header to 2 DVA's. This leads to a "NDVAs
inversion", where a parent block (the gang block header) has less DVA's
than its children (the gang members), causing an assertion failure in
zio_write_gang_member_ready().
This commit addresses the problem by only restricting the gang block
header to 2 DVA's if the block is actually encrypted (and thus its gang
block members can have at most 2 DVA's).
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#14250Closes#14356
Currently, if API tests fail, we either ignore the failures, or
unconditionally halt the kernel build. This leads to situations where
incompatibilities with existing APIs may develop, but not trip the
configure compatibility checks.
This introduces a new mechanism to require APIs for kernels above a
particular version. While not perfect, this at least guarantees
mainline kernels do not break existing APIs without at least providing
some warning.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Antonio Russo <aerusso@aerusso.net>
Closes#14343
The bi_rw member of struct bio was renamed to bi_opf in Linux 6.2.
As well, Linux's implementation of bio_set_op_attrs(...) has been
removed.
The HAVE_BIO_BI_OPF macro already appears to be defined, but the
removal of the bio_set_op_attrs(...) implementation makes the build
fall back on the locally-defined implementation, which isn't updated
for the bio->bi_opf change. This commit adds that update.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#14324Closes#14331
commit d27c81847b upstream
Linux 863f144 modified the .tmpfile interface to pass a struct file,
rather than a struct dentry, and expect the tmpfile implementation to
open inside of tmpfile().
This patch implements a configuration test that checks for this new API
and appropriately sets a HAVE_TMPFILE_DENTRY flag that tracks this old
API. Contingent on this flag, the appropriate API is implemented.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Antonio Russo <aerusso@aerusso.net>
Closes#14301Closes#14343
commit a7304ab9c1 upstream
mmapwrite is used during the ZTS to identify issues with mmap-ed files.
This helper program exercises this pathway by continuously writing to a
file. ee6bf97c7 modified the writing threads to terminate after a set
amount of total data is written. This change allows standard program
execution to reach the end of a writer thread without closing the file
descriptor, introducing a resource "leak."
This patch appeases resource leak analyses by close()-ing the file at
the end of the thread.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Antonio Russo <aerusso@aerusso.net>
Closes#14353
commit ee6bf97c77 upstream
mmapwrite spawns several threads, all of which perform writes on a file
for the purpose of testing the behavior of mmap(2)-ed files. One
thread performs an mmap and a write to the beginning of that region,
while the others perform regular writes after lseek(2)-ing the end of
the file.
Because these regular writes are set in a while (1) loop, they will
write an unbounded amount of data to disk. The mmap_write_001_pos test
script SIGKILLs them after 30 seconds, but on fast testbeds, this may
be enough time to exhaust the available space in the filesystem,
leading to spurious test failures.
Instead, limit the total file size by checking that the lseek return
value is no greater than 250 * 1024*1024 bytes, which is less than the
default minimum vdev size defined in includes/default.cfg .
This also includes part of 2a493a4c71,
which checks the return value of lseek.
Signed-off-by: Antonio Russo <aerusso@aerusso.net>
Closes#14277Closes#14345
zfs_zaccess_trivial() calls the generic_permission() to read
xattr attributes. This causes deadlock if called from
zpl_xattr_set_dir() context as xattr and the dent locks are
already held in this scenario. This commit skips the permissions
checks for extended attributes since the Linux VFS stack already
checks it before passing us the control.
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Currently, the receiver fails to override the encryption
property for the plain replicated dataset with the error:
"cannot receive incremental stream: encryption property
'encryption' cannot be set for incremental streams.". The
problem is resolved by allowing the receiver to override
the encryption property for plain replicated send.
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
If the attached disk already contains a vdev GUID, it
means the disk is not clean. In such a scenario, the
physical path would be a match that makes the disk
faulted when trying to online it. So, we would only
want to proceed if either GUID matches with the last
attached disk or the disk is in a clean state.
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
vdev_geom_read_pool_label() can leave NULL in configs. Check for it
and skip consistently when generating rootconf.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#14291
(cherry picked from commit dc8c2f6158)
Linux has an unresolved hang if you resize a pipe with bytes
in it.
Since there's no obvious way to detect this happening, added a
workaround to disable resizing the pipe buffer if you set an
environment variable.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#13309
Legacy mountpoint datasets should not pass `-o zfsutil` to `mount.zfs`.
Fix the logic in `mount_fs()` to not forget we have a legacy mountpoint
when checking for an `org.zol:mountpoint` userprop.
Reviewed-by: Richard Yao <ryao@gentoo.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#14274
(cherry picked from commit 786ff6a6cb)
The zfs-2.1.7 branch is still using the older 'python-dev'
package names rather than the newer 'python3-dev' packages that
are required for 'ubuntu-latest'. Use 'ubuntu-20.04' instead of
'ubuntu-latest' to get around this.
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
We are not allowed to dirty a filesystem when done receiving
a snapshot. In this case the flag SPA_FEATURE_LARGE_BLOCKS will
not be set on that filesystem since the filesystem is not on
dp_dirty_datasets, and a subsequent encrypted raw send will fail.
Fix this by checking in dsl_dataset_snapshot_sync_impl() if the feature
needs to be activated and do so if appropriate.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#13699Closes#13782
When local properties (e.g., from -o and -x) are provided, don't leak
the packed representation of the received properties due to variable
reuse.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Brooks Davis <brooks.davis@sri.com>
Closes#14197
When ZFS is built with assertions, a prefetch is done on a redacted
blkptr and `dpa->dpa_dnode` is NULL, we will have a NULL pointer
dereference in `dbuf_prefetch_indirect_done()`.
Both Coverity and Clang's Static Analyzer caught this.
Reported-by: Coverity (CID 1524671)
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14210
The port of lua to OpenZFS modified lua to use int64_t for numbers
instead of double. As part of this, a function for calculating
exponentiation was replaced with a bit shift. Unfortunately, it did not
handle negative values. Also, it only supported exponents numbers with
7 digits before before overflow. This supports exponents up to 15 digits
before overflow.
Clang's static analyzer reported this as "Result of operation is garbage
or undefined" because the exponent was negative.
Reviewed-by: Damian Szuberski <szuberskidamian@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14204
```
os/linux/zfs/zvol_os.c:1111:3: error: ignoring return value of function
declared with 'warn_unused_result' attribute [-Werror,-Wunused-result]
add_disk(zv->zv_zso->zvo_disk);
^~~~~~~~ ~~~~~~~~~~~~~~~~~~~~
zpl_xattr.c:1579:1: warning: no previous prototype for function
'zpl_posix_acl_release_impl' [-Wmissing-prototypes]
```
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: szubersk <szuberskidamian@gmail.com>
Closes#13551
(cherry picked from commit 9884319666)
In #13709, as in #11294 before it, it turns out that 63a26454 still had
the same failure mode as when it was first landed as d1d47691, and
fails to unlock certain datasets that formerly worked.
Rather than reverting it again, let's add handling to just throw out
the accounting metadata that failed to unlock when that happens, as
well as a test with a pre-broken pool image to ensure that we never get
bitten by this again.
Fixes: #13709
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
The original ARC paper called for an initial 50/50 MRU/MFU split
and this is accounted in various places where arc_p = arc_c >> 1,
with further adjustment based on ghost lists size/hit. However, in
current code both arc_adapt() and arc_get_data_impl() aggressively
grow arc_p until arc_c is reached, causing unneeded pressure on
MFU and greatly reducing its scan-resistance until ghost list
adjustments kick in.
This patch restores the original behavior of initially having arc_p
as 1/2 of total ARC, without preventing MRU to use up to 100% total
ARC when MFU is empty.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Gionatan Danti <g.danti@assyoma.it>
Closes#14137Closes#14120
There is an off by 1 error in the check. Fortunately, this function does
not appear to be used in kernel space, despite being compiled as part of
the kernel module. However, it is used in userspace. Callers of
lzc_ioctl_fd() likely will crash if they attempt to use the
unimplemented request number.
This was reported by FreeBSD's coverity scan.
Reported-by: Coverity (CID 1432059)
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Damian Szuberski <szuberskidamian@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14135
Some of our customers have been occasionally hitting zfs import failures
in Linux because udevd doesn't create the by-id symbolic links in time
for zpool import to use them. The main issue is that the
systemd-udev-settle.service that zfs-import-cache.service and other
services depend on is racy. There is also an openzfs issue filed (see
https://github.com/openzfs/zfs/issues/10891) outlining the problem and
potential solutions.
With the proper solutions being significant in terms of complexity and
the priority of the issue being low for the time being, this patch
exposes `zfs_vdev_open_timeout_ms` as a tunable so people that are
experiencing this issue often can increase it as a workaround.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Don Brady <don.brady@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Closes#14133
This fixes -Wsingle-bit-bitfield-constant-conversion warning from
clang-16 like:
lib/libzfs/libzfs_dataset.c:4529:19: error: implicit truncation
from 'int' to a one-bit wide bit-field changes value from
1 to -1 [-Werror,-Wsingle-bit-bitfield-constant-conversion]
flags.nounmount = B_TRUE;
^ ~~~~~~
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Brooks Davis <brooks.davis@sri.com>
Closes#14125
* The complaint in ztest_replay_write() is only possible if something
went horribly wrong. An assertion will silence this and if it goes
off, we will know that something is wrong.
* The complaint in spa_estimate_metaslabs_to_flush() is not impossible,
but seems very unlikely. We resolve this by passing the value from
the `MIN()` that does not go to infinity when the variable is zero.
There was a third report from Clang's scan-build, but that was a
definite false positive and disappeared when checked again through
Clang's static analyzer with Z3 refution via CodeChecker.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14124
CodeQL reported that when the VERIFY3U condition is false, we do not
pass enough arguments to `spl_panic()`. This is because the format
string from `snprintf()` was concatenated into the format string for
`spl_panic()`, which causes us to have an unexpected format specifier.
A CodeQL developer suggested fixing the macro to have a `%s` format
string that takes a stringified RIGHT argument, which would fix this.
However, upon inspection, the VERIFY3U check was never necessary in the
first place, so we remove it in favor of just calling `snprintf()`.
Lastly, it is interesting that every other static analyzer run on the
codebase did not catch this, including some that made an effort to catch
such things. Presumably, all of them relied on header annotations, which
we have not yet done on `spl_panic()`. CodeQL apparently is able to
track the flow of arguments on their way to annotated functions, which
llowed it to catch this when others did not. A future patch that I have
in development should annotate `spl_panic()`, so the others will catch
this too.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14098
Open files, which aren't present in the snapshot, which is being
roll-backed to, need to disappear from the visible VFS image of
the dataset.
Kernel provides d_drop function to drop invalid entry from
the dcache, but inode can be referenced by dentry multiple dentries.
The introduced zpl_d_drop_aliases function walks and invalidates
all aliases of an inode.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Pavel Snajdr <snajpa@snajpa.net>
Closes#9600Closes#14070
Clang's static analyzer complains about this.
In get_configs(), if we have an invalid configuration that has no top
level vdevs, we can read a couple of uninitialized variables. Aborting
upon seeing this would break the userland tools for healthy pools, so we
instead initialize the two variables to 0 to allow the userland tools to
continue functioning for the pools with valid configurations.
In zfs_do_wait(), if no wait activities are enabled, we read an
uninitialized error variable.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14043
If we encounter an EXDEV error when using the redacted snapshots
feature, the memory used by dspp.fromredactsnaps is leaked.
Clang's static analyzer caught this during an experiment in which I had
annotated various headers in an attempt to improve the results of static
analysis.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13973
If mechanism->cm_param is NULL, passing mechanism to
PROV_SHA2_GET_DIGEST_LEN() will dereference a NULL pointer.
Coverity reported this.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14044
Calling spa_open() will pass a NULL pointer to spa_open_common()'s
config parameter. Under the right circumstances, we will dereference the
config parameter without doing a NULL check.
Clang's static analyzer found this.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14044
Clang's static analyzer pointed out that whenever zap_lookup_by_dnode()
is called, we have the following stack where strlcpy() is passed a NULL
pointer for realname from zap_lookup_by_dnode():
strlcpy()
zap_lookup_impl()
zap_lookup_norm_by_dnode()
zap_lookup_by_dnode()
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14044
Clang's static analyzer complained that we dereference a NULL pointer in
dump_path() if we return 0 when there is an error.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14044
Coverity complained about a couple of uninitialized value reads in ZED.
* zfs_deliver_dle() can pass an uninitialized string to zed_log_msg()
* An uninitialized sev.sigev_signo is passed to timer_create()
The former would log garbage while the latter is not a real issue, but
we might as well suppress it by initializing the field to 0 for
consistency's sake.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14047
Out of the 12 defects in lua that coverity reports, 5 of them involve
`lua_typename()` and out of the dozens of defects in ZFS that lua
reports, 3 of them involve `lua_typename()` due to the ZCP code. Given
all of the uses of `lua_typename()` in the ZCP code, I was surprised
that there were not more. It appears that only 2 were reported because
only 3 called `lua_type()`, which does a defective sanity check that
allows invalid types to be passed.
lua/lua@d4fb848be7 addressed this in
upstream lua 5.3. Unfortunately, we did not get that fix since we use
lua 5.2 and we do not have assertions enabled in lua, so the upstream
solution would not do anything.
While we could adopt the upstream solution and enable assertions, a
simpler solution is to fix the issue by making `lua_typename()` return
`internal_type_error` whenever it is called with an invalid type. This
avoids the array overflow and if we ever see it appear somewhere, we
will know there is a problem with the lua interpreter.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13947
Users are allowed to pass NULL to resultp, but we unconditionally assume
that they never do. When an external user does pass NULL to resultp, we
dereference a NULL pointer.
Clang's static analyzer complained about this.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14008
This is a portability issue. The issue had already been fixed for
scripts/cstyle.pl by 2dbf1bf829.
scripts/enum-extract.pl was added to the repository the following year
without this portability fix.
Michael Bishop informed me that this broke his attempt to build ZFS
2.1.6 on NixOS, since he was building manually outside of their package
manager (that usually rewrites the shebangs to NixOS' unusual paths).
NixOS puts all of the paths into $PATH, so scripts that portably rely
on env to find the interpreter still work.
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14012
9a49c6b782 was intended to fix this issue,
but I had missed the case in pam_sm_open_session(). Clang's static
analyzer had not reported it and I forgot to look for other cases.
Interestingly, GCC gcc-12.1.1_p20220625's static analyzer had caught
this as multiple double-free bugs, since another failure after the
failure in zfs_key_config_load() will cause us to attempt to free the
memory that zfs_key_config_load() was supposed to allocate, but had
cleaned up upon failure.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13978
If the `list_head()` returns NULL, we dereference it, right before we
check to see if it returned NULL.
We have defined two different pointers that both point to the same
thing, which are `origin_head` and `origin_ds`. Almost everything uses
`origin_ds`, so we switch them to use `origin_ds`.
We also promote `origin_ds` to a const pointer so that the compiler
verifies that nothing modifies it.
Coverity complained about this.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Neal Gompa <ngompa@datto.com>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13967
82226e4f44 was intended to prevent a
warning from being printed in situations where it was inappropriate, but
accidentally disabled it entirely by setting featureflags in the wrong
case statement.
Coverity reported this as dead code.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13946
Clang's static analyzer found that config.uid is uninitialized when
zfs_key_config_load() returns an error.
Oddly, this was not included in the unchecked return values that
Coverity found.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13957
A comment says that the caller should free k_out, but the pointer passed
via k_out is not the same pointer we received from strdup(). Instead,
it is a pointer into the region we received from strdup(). The free
function should always be called with the original pointer, so this is
likely a bug.
We solve this by calling `strdup()` a second time and then freeing the
original pointer.
Coverity reported this as a memory leak.
Reviewed-by: Neal Gompa <ngompa@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13867
Commit ecd6cf800b63704be73fb264c3f5b6e0dafc068d by marks in OpenSolaris
at Tue Jun 26 07:44:24 2007 -0700 introduced a bug where we fail to call
`va_end()` before returning.
The man page for va_start() says:
"Each invocation of va_start() must be matched by a corresponding
invocation of va_end() in the same function."
Coverity complained about this.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Chunwei Chen <david.chen@nutanix.com>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13904
Coverity reported that we pass a pointer to zfsvfs to
`dmu_objset_disown()` after freeing zfsvfs in zfsvfs_create_impl() after
a failure in zfsvfs_init().
We have nearly identical duplicate versions of this code for FreeBSD and
Linux, but interestingly, the FreeBSD version of this code differs in
such a way that it does not suffer from this bug. We remove the
difference from the FreeBSD version to fix this bug.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13883
These were reported by Coverity as "Read from pointer after free" bugs.
Presumably, it did not report it as a use-after-free bug because it does
not understand the inline assembly that implements the atomic
instruction.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13881
We inherited membar_consumer() and membar_producer() from OpenSolaris,
but we had replaced membar_consumer() with Linux's smp_rmb() in
zfs_ioctl.c. The FreeBSD SPL consequently implemented a shim for the
Linux-only smp_rmb().
We reinstate membar_consumer() in platform independent code and fix the
FreeBSD SPL to implement membar_consumer() in a way analogous to Linux.
Reviewed-by: Konstantin Belousov <kib@FreeBSD.org>
Reviewed-by: Mateusz Guzik <mjguzik@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Neal Gompa <ngompa@datto.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13843
Currently, only Blake3 x86 Asm code has signs of being ENDBR-aware.
At least, under certain conditions it includes some header file and
uses some custom macro from there.
Linux has its own NOENDBR since several releases ago. It's defined
in the same <asm/linkage.h>, so currently <sys/asm_linkage.h>
already is provided with it.
Let's unify those two into one %ENDBR macro. At first, check if it's
present already. If so -- use Linux kernel version. Otherwise, try
to go that second way and use %_CET_ENDBR from <cet.h> if available.
If no, fall back to just empty definition.
This fixes a couple more 'relocations to !ENDBR' across the module.
And now that we always have the latest/actual ENDBR definition, use
it at the entrance of the few corresponding functions that objtool
still complains about. This matches the way how it's used in the
upstream x86 core Asm code.
Reviewed-by: Attila Fülöp <attila@fueloep.org>
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Closes#14035
objtool properly complains that it can't decode some of the
instructions from ICP x86 Asm code. As mentioned in the Makefile,
where those object files were excluded from objtool check (but they
can still be visible under IBT and LTO), those are just constants,
not code.
In that case, they must be placed in .rodata, so they won't be
marked as "allocatable, executable" (ax) in EFL headers and this
effectively prevents objtool from trying to decode this data. That
reveals a whole bunch of other issues in ICP Asm code, as previously
objtool was bailing out after that warning message.
Reviewed-by: Attila Fülöp <attila@fueloep.org>
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Closes#14035
Conflicts:
module/Kbuild.in
Commit 43569ee374 ("Fix objtool: missing int3 after ret warning")
addressed replacing all `ret`s in x86 asm code to a macro in the
Linux kernel in order to enable SLS. That was done by copying the
upstream macro definitions and fixed objtool complaints.
Since then, several more mitigations were introduced, including
Rethunk. It requires to have a jump to one of the thunks in order
to work, so the RET macro was changed again. And, as ZFS code
didn't use the mainline defition, but copied it, this is currently
missing.
Objtool reminds about it time to time (Clang 16, CONFIG_RETHUNK=y):
fs/zfs/lua/zlua.o: warning: objtool: setjmp+0x25: 'naked' return
found in RETHUNK build
fs/zfs/lua/zlua.o: warning: objtool: longjmp+0x27: 'naked' return
found in RETHUNK build
Do it the following way:
* if we're building under Linux, unconditionally include
<linux/linkage.h> in the related files. It is available in x86
sources since even pre-2.6 times, so doesn't need any conftests;
* then, if RET macro is available, it will be used directly, so that
we will always have the version actual to the kernel we build;
* if there's no such macro, we define it as a simple `ret`, as it
was on pre-SLS times.
This ensures we always have the up-to-date definition with no need
to update it manually, and at the same time is safe for the whole
variety of kernels ZFS module supports.
Then, there's a couple more "naked" rets left in the code, they're
just defined as:
.byte 0xf3,0xc3
In fact, this is just:
rep ret
`rep ret` instead of just `ret` seems to mitigate performance issues
on some old AMD processors and most likely makes no sense as of
today.
Anyways, address those rets, so that they will be protected with
Rethunk and SLS. Include <sys/asm_linkage.h> here which now always
has RET definition and replace those constructs with just RET.
This wipes the last couple of places with unpatched rets objtool's
been complaining about.
Reviewed-by: Attila Fülöp <attila@fueloep.org>
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Closes#14035
User props trigger an assert in zfs_prop_inheritable(), we must check
if the prop is a user prop first.
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Backported as snippit from:
63652e1 Add --enable-asan and --enable-ubsan switches
zed aborts and dumps core in vdev_whole_disk_from_config() if
wholedisk property does not exist. make_leaf_vdev() adds the
property but there may be already pools that don't have the
wholedisk in the label.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#14062
Commit 68ddc06b61 introduced support
for receiving unencrypted datasets as children of encrypted ones but
unfortunately got the logic upside down. This resulted in failing to
deny receives of incremental sends into encrypted datasets without
their keys loaded. If receiving a filesystem, the receive was done
into a newly created unencrypted child dataset of the target. In
case of volumes the receive made the target volume undeletable since
a dataset was created below it, which we obviously can't handle.
Incremental streams with embedded blocks are affected as well.
We fix the broken logic to properly deny receives in such cases.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Attila Fülöp <attila@fueloep.org>
Closes#13598Closes#14055Closes#14119
Rather than panic debug builds when we fail to parse a whole ZIL, let's
instead improve the logging of errors and continue like in a release
build.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#14116
This patch relax the quota limitation for dataset by around 3%.
What this means is that user can write more data then the quota is
set to. However thanks to that we can get more stable bandwidth, in
case when we are overwriting data in-place, and not consuming any
additional space.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Mariusz Zaborski <oshogbo@vexillium.org>
Sponsored-by: Zededa Inc.
Sponsored-by: Klara Inc.
Closes#13839
Reclaim metadata when arc_available_memory < 0 even if
meta_used is not bigger than arc_meta_limit.
As described in https://github.com/openzfs/zfs/issues/14054 if
zfs_arc_meta_limit_percent=100 then ARC target can collapse to
arc_min due to arc_purge not freeing any metadata.
This patch lets arc_prune to do its work when arc_available_memory
is negative even if meta_used is not bigger than arc_meta_limit,
avoiding ARC target collapse.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Gionatan Danti <g.danti@assyoma.it>
Closes#14054Closes#14093
The autotrim thread only reads zfs_trim_extent_bytes_min and
zfs_trim_extent_bytes_max variable only on thread start. We
should check for parameter changes during thread execution to
allow parameter changes take effect without needing to disable
then restart the autotrim.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Václav Skála <skala@vshosting.cz>
Closes#14077
After Linux 6.1-rc1 came out, the build started failing to build a
couple of the files in the linux spl code due to the mutex_init
redefinition. Moving the sys/mutex.h include to a lower position within
these two files appears to fix the problem.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#14040
Update the META file to reflect compatibility with the 6.0 kernel.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#14091
ZFS_LINUX_TRY_COMPILE_HEADER macro doesn't take CONFIG_ZFS=y into
account. As a result, on several latest Linux versions, configure
script marks DECLARE_EVENT_CLASS() available for non-GPL when ZFS
is being built as a module, but marks it unavailable when ZFS is
built-in.
Follow the logic of the neighbor macros and adjust
ZFS_LINUX_TRY_COMPILE_HEADER accordingly, so that it doesn't try
to look for a .ko when ZFS is built-in.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Closes#14006
Before this patch, in zfs_domount, if zfs_root or d_make_root fails, we
leave zfsvfs != NULL. This will lead to execution of the error handling
`if` statement at the `out` label, and hence to a call to
dmu_objset_disown and zfsvfs_free.
However, zfs_umount, which we call upon failure of zfs_root and
d_make_root already does dmu_objset_disown and zfsvfs_free.
I suppose this patch rather adds to the brittleness of this part of the
code base, but I don't want to invest more time in this right now.
To add a regression test, we'd need some kind of fault injection
facility for zfs_root or d_make_root, which doesn't exist right now.
And even then, I think that regression test would be too closely tied
to the implementation.
To repro the double-disown / double-free, do the following:
1. patch zfs_root to always return an error
2. mount a ZFS filesystem
Here's the stack trace you would see then:
VERIFY3(ds->ds_owner == tag) failed (0000000000000000 == ffff9142361e8000)
PANIC at dsl_dataset.c:1003:dsl_dataset_disown()
Showing stack for process 28332
CPU: 2 PID: 28332 Comm: zpool Tainted: G O 5.10.103-1.nutanix.el7.x86_64 #1
Call Trace:
dump_stack+0x74/0x92
spl_dumpstack+0x29/0x2b [spl]
spl_panic+0xd4/0xfc [spl]
dsl_dataset_disown+0xe9/0x150 [zfs]
dmu_objset_disown+0xd6/0x150 [zfs]
zfs_domount+0x17b/0x4b0 [zfs]
zpl_mount+0x174/0x220 [zfs]
legacy_get_tree+0x2b/0x50
vfs_get_tree+0x2a/0xc0
path_mount+0x2fa/0xa70
do_mount+0x7c/0xa0
__x64_sys_mount+0x8b/0xe0
do_syscall_64+0x38/0x50
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Co-authored-by: Christian Schwarz <christian.schwarz@nutanix.com>
Signed-off-by: Christian Schwarz <christian.schwarz@nutanix.com>
Closes#14025
On older kernels, the definition for `module_param_call()` typecasts
function pointers to `(void *)`, which triggers -Werror, causing the
check to return false when it should return true.
Fixing this breaks the build process on some older kernels because they
define a `__check_old_set_param()` function in their headers that checks
for a non-constified `->set()`. We workaround that through the c
preprocessor by defining `__check_old_set_param(set)` to `(set)`, which
prevents the build failures.
However, it is now apparent that all kernels that we support have
adopted the GRSecurity change, so there is no need to have an explicit
autotools check for it anymore. We therefore remove the autotools check,
while adding the workaround to our headers for the build time
non-constified `->set()` check done by older kernel headers.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13984Closes#14004
= Problem
While examining a customer's system we noticed unreasonable space
usage from a few snapshots due to gang blocks. Under some further
analysis we discovered that the pool would create gang blocks because
all its disks had non-zero write error counts and they'd be skipped
for normal metaslab allocations due to the following if-clause in
`metaslab_alloc_dva()`:
```
/*
* Avoid writing single-copy data to a failing,
* non-redundant vdev, unless we've already tried all
* other vdevs.
*/
if ((vd->vdev_stat.vs_write_errors > 0 ||
vd->vdev_state < VDEV_STATE_HEALTHY) &&
d == 0 && !try_hard && vd->vdev_children == 0) {
metaslab_trace_add(zal, mg, NULL, psize, d,
TRACE_VDEV_ERROR, allocator);
goto next;
}
```
= Proposed Solution
Get rid of the predicate in the if-clause that checks the past
write errors of the selected vdev. We still try to allocate from
HEALTHY vdevs anyway by checking vdev_state so the past write
errors doesn't seem to help us (quite the opposite - it can cause
issues in long-lived pools like the one from our customer).
= Testing
I first created a pool with 3 vdevs:
```
$ zpool list -v volpool
NAME SIZE ALLOC FREE
volpool 22.5G 117M 22.4G
xvdb 7.99G 40.2M 7.46G
xvdc 7.99G 39.1M 7.46G
xvdd 7.99G 37.8M 7.46G
```
And used `zinject` like so with each one of them:
```
$ sudo zinject -d xvdb -e io -T write -f 0.1 volpool
```
And got the vdevs to the following state:
```
$ zpool status volpool
pool: volpool
state: ONLINE
status: One or more devices has experienced an unrecoverable error.
...<cropped>..
action: Determine if the device needs to be replaced, and clear the
...<cropped>..
config:
NAME STATE READ WRITE CKSUM
volpool ONLINE 0 0 0
xvdb ONLINE 0 1 0
xvdc ONLINE 0 1 0
xvdd ONLINE 0 4 0
```
I also double-checked their write error counters with sdb:
```
sdb> spa volpool | vdev | member vdev_stat.vs_write_errors
(uint64_t)0 # <---- this is the root vdev
(uint64_t)2
(uint64_t)1
(uint64_t)1
```
Then I checked that I the problem was reproduced in my VM as I the
gang count was growing in zdb as I was writting more data:
```
$ sudo zdb volpool | grep gang
ganged count: 1384
$ sudo zdb volpool | grep gang
ganged count: 1393
$ sudo zdb volpool | grep gang
ganged count: 1402
$ sudo zdb volpool | grep gang
ganged count: 1414
```
Then I updated my bits with this patch and the gang count stayed the
same.
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Closes#14003
Setups that have a lot of zvols may see zvol_wait terminate prematurely
even though the script is still making progress. For example, we have a
customer that called zvol_wait for ~7100 zvols and by the last iteration
of that script it was still waiting on ~2900. Similarly another one
called zvol_wait for 2200 and by the time the script terminated there
were only 50 left.
This patch adjusts the logic to stay within the outer loop of the script
if we are making any progress whatsoever.
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed-by: Don Brady <don.brady@delphix.com>
Signed-off-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Closes#13998
arc_summary currently list prefetch stats as "demand prefetch"
However, a hit/miss can be due to demand or prefetch, not both.
To remove any confusion, this patch removes the "Demand" word
from the affected lines.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Gionatan Danti <g.danti@assyoma.it>
Closes#13985
= Issue
Recently we hit an assertion panic in `dsl_process_sub_livelist` while
exporting the spa and interrupting `bpobj_iterate_nofree`. In that case
`bpobj_iterate_nofree` stops mid-way returning an EINTR without clearing
the intermediate AVL tree that keeps track of the livelist entries it
has encountered so far. At that point the code has a VERIFY for the
number of elements of the AVL expecting it to be zero (which is not the
case for EINTR).
= Fix
Cleanup any intermediate state before destroying the AVL when
encountering EINTR. Also added a comment documenting the scenario where
the EINTR comes up. There is no need to do anything else for the calles
of `dsl_process_sub_livelist` as they already handle the EINTR case.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Closes#13939
The current value causes significant artificial slowdown during mass
parallel file removal, which can be observed both on FreeBSD and Linux
when running real workloads.
Sample results from Linux doing make -j 96 clean after an allyesconfig
modules build:
before: 4.14s user 6.79s system 48% cpu 22.631 total
after: 4.17s user 6.44s system 153% cpu 6.927 total
FreeBSD results in the ticket.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#13932Closes#13938
Currently, additional/extra copies are created for metadata in
addition to the redundancy provided by the pool(mirror/raidz/draid),
due to this 2 times more space is utilized per inode and this decreases
the total number of inodes that can be created in the filesystem. By
setting redundant_metadata to none, no additional copies of metadata
are created, hence can reduce the space consumed by the additional
metadata copies and increase the total number of inodes that can be
created in the filesystem. Additionally, this can improve file create
performance due to the reduced amount of metadata which needs
to be written.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Dipak Ghosh <dipak.ghosh@hpe.com>
Signed-off-by: Akash B <akash-b@hpe.com>
Closes#13680
vm_object_page_clean() expects that the associated vnode is locked
as VOP_PUTPAGES() may get called on the vnode.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Andriy Gapon <avg@FreeBSD.org>
Closes#14079
(cherry picked from commit 41133c9794)
- Add a zfs_exit() call in an error path, otherwise a lock is leaked.
- Remove the fid_gen > 1 check. That appears to be Linux-specific:
zfsctl_snapdir_fid() sets fid_gen to 0 or 1 depending on whether the
snapshot directory is mounted. On FreeBSD it fails, making snapshot
dirs inaccessible via NFS.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Andriy Gapon <avg@FreeBSD.org>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Fixes: 43dbf88178 ("FreeBSD: vfsops: use setgen for error case")
Closes#14001Closes#13974
(cherry picked from commit ed566bf1cd)
This patch handles the race condition on simultaneous failure of
2 drives, which misses the vdev_rebuild_reset_wanted signal in
vdev_rebuild_thread. We retry to catch this inside the
vdev_rebuild_complete_sync function.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Dipak Ghosh <dipak.ghosh@hpe.com>
Reviewed-by: Akash B <akash-b@hpe.com>
Signed-off-by: Samuel Wycliffe J <samwyc@hpe.com>
Closes#14041Closes#14050
Due to a missing semicolon on the ExecStart line, it wasn't possible
to specify the snapshot name on the bootfs.{rollback,snapshot}
kernel parameters if the boot dataset name was obtained from the
root=zfs:... kernel parameter.
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Gregory Bartholomew <gregory.lee.bartholomew@gmail.com>
Closes#13585
This error occurred when building on Gentoo with debugging enabled:
zfs-kmod-2.1.6/work/zfs-2.1.6/module/icp/core/kcf_sched.c:1277:14:
error: a function declaration without a prototype is deprecated
in all versions of C [-Werror,-Wstrict-prototypes]
kcfpool_alloc()
^
void
1 error generated.
This function is not present in master.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14023
Otherwise, systemd-sysv-generator will generate a service equivalent
that breaks the boot: under systemd this is covered by
zfs-mount-generator
We already do this for zfs-import.service, and other init scripts are
suppressed automatically by the "actual" .service files
Fixes: commit f04b976200 ("Add init script
to load keys")
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#14010Closes#14019
A followup to d7a67402a8
For `mount -t zfs -o opts ds mp` command line
some implementations of `mount(8)`, e. g. Busybox in Debian
work as follows:
```
newfstatat(AT_FDCWD, "ds", 0x7fff826f4ab0, 0) = -1
mount("ds", "mp", "zfs", MS_SILENT, NULL) = 0
```
The logic above skips completely `mount.zfs` and prevents us
from reading filesystem properties and applying mount options.
For comparison, the coreutils `mount(8)` implementation does:
```
openat(AT_FDCWD, "/proc/filesystems", O_RDONLY|O_CLOEXEC) = 3
// figure out that zfs is a `nodev` filesystem and look for a helper
newfstatat(AT_FDCWD, "/sbin/mount.zfs" ...) = 0
execve("/sbin/mount.zfs" ...) = 0
```
Using `mount.zfs` in initramfs would help circumvent deficiencies
of some of `mount(8)` implementations. `mount -t zfs` translates
to `mount.zfs` invocation, except for cases when explicitly disabled
by `-i`.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: szubersk <szuberskidamian@gmail.com>
Closes#13305
(cherry picked from commit 35d81a75a8)
Clang's static analyzer found a bad free caused by skein_mac_atomic().
It will allocate a context on the stack and then pass it to
skein_final(), which attempts to free it. Upon inspection,
skein_digest_atomic() also has the same problem.
These functions were created to match the OpenSolaris ICP API, so I was
curious how we avoided this in other providers and looked at the SHA2
code. It appears that SHA2 has a SHA2Final() helper function that is
called by the exported sha2_mac_final()/sha2_digest_final() as well as
the sha2_mac_atomic() and sha2_digest_atomic() functions. The real work
is done in SHA2Final() while some checks and the free are done in
sha2_mac_final()/sha2_digest_final().
We fix the use after free in the skein code by taking inspiration from
the SHA2 code. We introduce a skein_final_nofree() that does most of the
work, and make skein_final() into a function that calls it and then
frees the memory.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13954
If you force fault a drive that's resilvering, it's scan stats can get
frozen in time, giving the false impression that it's being resilvered.
This commit checks the vdev state to see if the vdev is healthy before
reporting "resilvering" or "repairing" in zpool status.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#13927Closes#13930
When reviewing #13875, I noticed that our FreeBSD code has an issue
where it converts from `int64_t` to `int` when calling
`vnlru_free{,_vfsops}()`. The result is that if the int64_t is `1 <<
36`, the int will be 0, since the low bits are 0. Even when some low
bits are set, a value such as `((1 << 36) + 1)` would truncate to 1,
which is wrong.
There is protection against this on 32-bit platforms, but on 64-bit
platforms, there is no check to protect us, so we add a check.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13882
Coverity complained about this. An error from `hkdf_sha512()` before uio
initialization will cause pointers to uninitialized memory to be passed
to `zio_crypt_destroy_uio()`. This is a regression that was introduced
by cf63739191. Interestingly, this never
affected FreeBSD, since the FreeBSD version never had that patch ported.
Since moving uio initialization to the top of this function would slow
down the qat_crypt() path, we only move the `memset()` calls to the top
of the function. This is sufficient to fix this problem.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Neal Gompa <ngompa@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13944
Original Log Size Limit implementation blocked all writes in case of
limit reached until the TXG is committed and the log is freed. It
caused huge delays and following speed spikes in application writes.
This implementation instead smoothly throttles writes, using exactly
the same mechanism as used for dirty data.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: jxdking <lostking2008@hotmail.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Issue #12284Closes#13476
This reverts commit 34dbc618f5. While this
change resolved the lock contention observed for certain workloads, it
inadventantly reduced the maximum hash inserts/removes per second. This
appears to be due to the slightly higher acquisition cost of a rwlock vs
a mutex.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
I see a few issues in the issue tracker that might be aided by being
able to turn this on. We have no module parameter for it, so I would
like to add one.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13874
We pass sizeof (struct redact_record *) rather than sizeof (struct
redact_record). Passing the pointer size is wrong.
Coverity caught this in two places.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13885
For encrypted raw receive, objset creation is delayed until a call to
dmu_recv_stream(). ZFS_PROP_SHARESMB property requires objset to be
populated when calling zpl_earlier_version(). To correctly handle the
ZFS_PROP_SHARESMB property for encrypted raw receive, this change
delays setting the property.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#13878
- Some optimizations for bqueue enqueue/dequeue.
- Added a fix to prevent deadlock when both bqueue_enqueue_impl()
and bqueue_dequeue() waits for signal to be triggered.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#13855
When iterating through children physical ashifts for vdev, prefer
ones above the maximum logical ashift, that we can actually use,
but within the administrator defined maximum.
When selecting top-level vdev ashift, do not set it to the defined
maximum in case physical ashift is even higher, but just ignore one.
Using the maximum does not prevent misaligned writes, but reduces
space efficiency. Since ZFS tries to write data sequentially and
aggregates the writes, in many cases large misanigned writes may be
not as bad as the space penalty otherwise.
Allow internal physical ashifts for vdevs higher than SHIFT_MAX.
May be one day allocator or aggregation could benefit from that.
Reduce zfs_vdev_max_auto_ashift default from 16 (64KB) to 14 (16KB),
so that ZFS may still use bigger ashifts up to SHIFT_MAX (64KB),
but only if it really has to or explicitly told to, but not as an
"optimization".
There are some read-intensive NVMe SSDs that report Preferred Write
Alignment of 64KB, and attempt to build RAIDZ2 of those leads to a
space inefficiency that can't be justified. Instead these changes
make ZFS fall back to logical ashift of 12 (4KB) by default and
only warn user that it may be suboptimal for performance.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#13798
For #13083, curiously, it did not print the actual error, just
that the compile failed with "Error 1".
In theory, this flag should cause it to report errors twice sometimes.
In practice, I'm pretty okay with reporting some twice if it avoids
reporting some never.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Damian Szuberski <szuberskidamian@gmail.com>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#13086
zfs_wrlog_data_max
The upper limit of TX_WRITE log data. Once it is reached,
write operation is blocked, until log data is cleared out
after txg sync. It only counts TX_WRITE log with WR_COPIED
or WR_NEED_COPY.
Reviewed-by: Prakash Surya <prakash.surya@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: jxdking <lostking2008@hotmail.com>
Closes#12284
Use dp_dirty_pertxg[] for txg_kick(), instead of dp_dirty_total in
original code. Extra parameter "txg" is added for txg_kick(), thus it
knows which txg to kick. Also txg_kick() call is moved from
dsl_pool_need_dirty_delay() to dsl_pool_dirty_space() so that we can
know the txg number assigned for txg_kick().
Some unnecessary code regarding dp_dirty_total in txg_sync_thread() is
also cleaned up.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: jxdking <lostking2008@hotmail.com>
Closes#12274
- Some optimizations for bqueue enqueue/dequeue.
- Added a fix to prevent deadlock when both bqueue_enqueue_impl()
and bqueue_dequeue() waits for signal to be triggered.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#13855
Without this patch, the
ASSERT3U(dbuf_is_metadata(db), ==, arc_is_metadata(buf));
at the beginning of dbuf_assign_arcbuf can panic
if the object type is a DMU_OT_NEWTYPE that has
DMU_OT_METADATA set.
While we're at it, fix DMU_OT_IS_ENCRYPTED as well.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Christian Schwarz <christian.schwarz@nutanix.com>
Closes#13842
Add physical device size/capacity only for physical devices in
'zpool list -v' instead of displaying "-" in the SIZE column.
This would make it easier to see the individual device capacity and
to determine which spares are large enough to replace which devices.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Dipak Ghosh <dipak.ghosh@hpe.com>
Signed-off-by: Akash B <akash-b@hpe.com>
Closes#12561Closes#13106
Special allocation class or dedup vdevs may have roughly the same
performance as L2ARC vdevs. Introduce a new tunable to exclude those
buffers from being cacheable on L2ARC.
Reviewed-by: Don Brady <don.brady@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#11761Closes#12285
Before:
$ time make cstyle
real 0m23.118s
user 0m23.002s
sys 0m0.114s
After:
$ time make cstyle
real 0m4.577s
user 0m31.487s
sys 0m0.699s
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Issue #12899
Users were seeing floods of `config_sync` events when autoexpand was
enabled. This happened because all "disk status change" udev events
invoke the autoexpand codepath, which calls zpool_relabel_disk(),
which in turn cause another "disk status change" event to happen,
in a feedback loop. Note that "disk status change" happens every time
a user calls close() on a block device.
This commit breaks the feedback loop by only allowing an autoexpand
to happen if the disk actually changed size.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes: #7132Closes: #7366Closes#13729
Some ARM BSPs run the Android kernel, which has
a modified xattr_handler->get() function signature.
This adds support to compile against these kernels.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Walter Huf <hufman@gmail.com>
Closes#13824
ZFS_MODULE_PARAM_CALL handlers implement their own locking if needed
and do not require Giant.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#13756
It makes sense to free memory in smaller chunks when approaching
arc_c_min to let other kernel subsystems to free more, since after
that point we can't free anything. This also matches behavior on
Linux, where to shrinker reported only the size above arc_c_min.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#13794
When importing from cachefile, it is possible that the builtin retry
logic will trip an assertion because it also fails to find the pool.
This fix addresses that case and returns the correct error message to
the user.
Reviewed-by: Richard Yao <ryao@gentoo.org>
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Wilson <gwilson@delphix.com>
Closes#13781
`zpool_expand_001_pos` was often failing due to not seeing autoexpand
commands in the `zpool history`. During testing, I found this to be
unreliable (sometimes the "online" wouldn't appear in `zpool history`)
and unnecessary, as we could simply check that the pool increased in
size.
This commit revamps the test to check for the expanded pool size
and corresponding new free space.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#13743
We tried replacing an NVMe drive using autoreplace, only
to see zed reject it with:
zed[27955]: zed_udev_monitor: /dev/nvme5n1 no devid source
This happened because ZED saw that ID_BUS was not set by udev
for the NVMe drive, and thus didn't think it was "real drive".
This commit allows NVMe drives to be autoreplaced even if
ID_BUS is not set.
Reviewed-by: Don Brady <don.brady@intel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#13512Closes#13646
libudev will sometimes falsely identify an 'atari' partition on a
blank disk, preventing it from being used in an autoreplace. This
seems to be a known issue. The workaround is to just ignore the
fake partition and continue with the autoreplace.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#13497Closes#13632
Get rid of RPM warnings on AlmaLinux 9:
"It's not recommended to have unversioned Obsoletes"
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#13584Closes#13638
This tightly links the subpackages together and ensures that everything
is upgraded together.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Neal Gompa <ngompa@datto.com>
Closes#13489
When the zfs-snapshot-bootfs service attempts to create a snapshot
that already exists, the exit status of the command is non-zero and
the service reports failed to the systemd service manager. This is a
common occurrence if bootfs.snapshot is left set on the kernel command
line and it should not be considered a failure.
This service was originally set to ignore this error by prefixing
the command with - on the ExecStart line, but the leading - appears
to have been dropped in #13359.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Gregory Bartholomew <gregory.lee.bartholomew@gmail.com>
Closes#13769
When the -p option is used, a list of floats is passed to sep.join(),
which expects strings. Fix this by converting each value to a string.
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Roberto Ricci <ricci@disroot.org>
Closes#12916Closes#13767
The 6.0 kernel added a printf-style var-arg for args > 0 to the
register_shrinker function, in order to add names to shrinkers, in
commit e33c267ab70de4249d22d7eab1cc7d68a889bac2. This enables the
shrinkers to have friendly names exposed in /sys/kernel/debug/shrinker/.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#13748
As of the Linux 5.20 kernel blk_cleanup_disk() has been removed,
all callers should use put_disk().
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13728
As of the Linux 5.20 kernel bdevname() has been removed, all
callers should use snprintf() and the "%pg" format specifier.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13728
Update the META file to reflect compatibility with the 5.19 kernel.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13715
zdb -d <pool>/<objset ID> does not work when
other command line arguments are included i.e.
zdb -U <cachefile> -d <pool>/<objset ID>
This change fixes the command line parsing
to handle this situation. Also fix issue
where zdb -r <dataset> <file> does not handle
the root <dataset> of the pool. Introduce -N
option to force <objset ID> to be interpreted
as a numeric objsetID.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Rich Ercolani <rincebrain@gmail.com>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Paul Zuchowski <pzuchowski@datto.com>
Closes#12845Closes#12944
Currently, dmu_read_uio_dnode can read 64K of a requested 1M in one
loop, get EFAULT back from zfs_uiomove() (because the iovec only holds
64k), and return EFAULT, which turns into EAGAIN on the way out. EAGAIN
gets interpreted as "I didn't read anything", the caller tries again
without consuming the 64k we already read, and we're stuck.
This apparently works on newer kernels because the caller which breaks
on older Linux kernels by happily passing along a 1M read request and a
64k iovec just requests 64k at a time.
With this, we now won't return EFAULT if we got a partial read.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12370Closes#12509Closes#12516
Not all Linux distribution kernels enable io_uring support by
default. Update the run time check to verify that the booted
kernel was built with CONFIG_IO_URING=y.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Co-authored-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13648Closes#13685
Since the assembly routines calculating SHA checksums don't use
a standard stack layout, CFI directives are needed to unroll the
stack.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Attila Fülöp <attila@fueloep.org>
Closes#11733
Switch to using asprintf() to satisfy the compiler and resolve the
potential format-overflow warning. Not the conditional before the
sprintf() would have prevented this regardless.
cmd/zfs/zfs_project.c: In function ‘zfs_project_handle_dir’:
cmd/zfs/zfs_project.c:241:38: error: ‘/’ directive writing
1 byte into a region of size between 0 and 4352
[-Werror=format-overflow=]
cmd/zfs/zfs_project.c:241:17: note: ‘sprintf’ output between
2 and 4609 bytes into a destination of size 4352
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13528Closes#13575
Extend the buffer slightly resolve the warning.
cmd/zfs/zfs_main.c: In function ‘upgrade_set_callback’:
cmd/zfs/zfs_main.c:2446:22: error: ‘%llu’ directive output
may be truncated writing between 1 and 20 bytes into a
region of size 16 [-Werror=format-truncation=]
cmd/zfs/zfs_main.c:2445:24: note: ‘snprintf’ output between
2 and 21 bytes into a destination of size 16
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13528Closes#13575
Move the use of the db pointer after it is freed. It's only used as
a tag so a dereference would never occur, but there's no reason we
can't invert the order to resolve the warning.
module/zfs/dbuf.c: In function 'dbuf_destroy':
module/zfs/dbuf.c:2953:17: error:
pointer 'db' may be used after 'free' [-Werror=use-after-free]
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13528Closes#13575
Move the use of the private pointer after it is freed. It's only
used as a tag so a dereference would never occur, but there's no
harm in inverting the order to resolve the warning.
module/zfs/dbuf.c: In function 'dbuf_issue_final_prefetch_done':
module/zfs/dbuf.c:3204:17: error:
pointer 'private' may be used after 'free' [-Werror=use-after-free]
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13528Closes#13575
The memcpy(), memmove(), and memset() functions have been annotated
to perform bounds checking when using FORTIFY_SOURCE. A warning is
now generted when writing beyond the end of the specified field.
Alternately, the new struct_group() macro could be used to create
an anonymous union member for use by memcpy(). However, since this
is the only place the macro would be helpful it's preferable to
restructure the code slights to avoid the need for additional
compatibility code when the macro does not exist.
https://lore.kernel.org/lkml/20211118183807.1283332-1-keescook@chromium.org/T/
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13528Closes#13575
The wrong union memory was being accessed in EdonRInit resulting in
a write beyond size of field compiler warning. Reference the correct
member to resolve the warning. The warning was correct and this in
case the mistake was harmless.
In function ‘fortify_memcpy_chk’,
inlined from ‘EdonRInit’ at zfs/module/icp/algs/edonr/edonr.c:494:3:
./include/linux/fortify-string.h:344:25: error: call to
‘__write_overflow_field’ declared with attribute warning:
detected write beyond size of field (1st parameter);
maybe use struct_group()? [-Werror=attribute-warning]
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13528Closes#13575
Restructure the code in zfs_log_xvattr() to use a lr_attr_end
structure when accessing lr_attr_t elements located after the
variable sized array. This makes the code more understandable
and resolves the accessing beyond the end of the field warnings.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13528Closes#13575
This code should be kept inline with the upstream lua version as much
as possible. Therefore, we simply want to silence the warning. This
check was enabled by default as part of -Wall in gcc 12.1.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13528Closes#13575
It may happen that scan bookmark points to a block that was turned
into a part of a big hole. In such case dsl_scan_visitbp() may skip
it and dsl_scan_check_resume() will not be called for it. As result
new scan suspend won't be possible until the end of the object, that
may take hours if the object is a multi-terabyte ZVOL on a slow HDD
pool, stretching TXG to all that time, creating all sorts of problems.
This patch changes the resume condition to any greater or equal block,
so even if we miss the bookmarked block, the next one we find will
delete the bookmark, allowing new suspend.
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Before this change for every valid parity column raidz_parity_verify()
allocated new buffer and copied there existing data, then recalculated
the parity and compared the result with the copy. This patch removes
the memory copy, simply swapping original buffer pointers with newly
allocated empty ones for parity recalculation and comparison. Original
buffers with potentially incorrect parity data are then just freed,
while new recalculated ones are used for repair.
On a pool of 12 4-wide raidz vdevs, storing 1.5TB of 16MB blocks, this
change reduces memory traffic during scrub by 17% and total unhalted
CPU time by 25%.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#13613
Issuing several scrub reads for a block we may use the parent ZIO
buffer for one of child ZIOs. If that read complete successfully,
then we won't need to copy the data explicitly. If block has only
one copy (typical for root vdev, which is also a mirror inside),
then we never need to copy -- succeed or fail as-is. Previous
code also copied data from buffer of every successfully completed
child ZIO, but that just does not make any sense.
On healthy N-wide mirror this saves all N+1 (or even more in case
of ditto blocks) memory copies for each scrubbed block, allowing
CPU to focus mostly on check-summing. For other vdev types it
should save one memory copy per block copy at root vdev.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#13606
Block statistics calculation during scrub I/O issue in case of sorted
scrub accounted ditto blocks several times. Embedded blocks on other
side were not accounted at all. This change moves the accounting from
issue to scan stage, that fixes both problems and also allows to avoid
pool-wide locking and the lock contention it created.
Since this statistics is quite specific and is not even exposed now
anywhere, disable its calculation by default to not waste CPU time.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#13579
Change math to make it like the ARC, using multiplications instead.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#13591
- Introduce first element offset within a leaf. It allows to reduce
by ~50% average memmove() size when adding/removing elements. If the
added/removed element is in the first half of the leaf, we may shift
elements before it and adjust the bth_first instead of moving more
elements after it.
- Use memcpy() instead of memmove() when we know there is no overlap.
- Switch from uint64_t to uint32_t. It does not limit anything,
but 32-bit arches should appreciate it greatly in hot paths.
- Store leaf capacity in struct btree to avoid 64-bit divisions.
- Adjust zfs_btree_insert_into_leaf() to always result in balanced
leaves after splitting, no matter where the new element was inserted.
Not that we care about it much, but it should also allow B-trees with
as little as two elements per leaf instead of 4 previously.
When scrubbing pool of 12 SSDs, storing 1.5TB of 4KB zvol blocks this
reduces amount of time spent in memmove() inside the scan thread from
13.7% to 5.7% and total scrub time by ~15 seconds out of 9 minutes.
It should also reduce spacemaps load time, but I haven't measured it.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#13582
- Reduce size and comparison complexity of q_exts_by_size B-tree.
Previous code used two 64-bit divisions and many other operations to
compare two B-tree elements. It created enormous overhead. This
implementation moves the math to the upper level and stores the score
in the B-tree elements themselves. Since all that we need to store in
that B-tree is the extent score and offset, those can fit into single
8 byte value instead of 24 bytes of q_exts_by_addr element and can be
compared with single operation.
- Better decouple secondary tree logic from main range_tree by moving
rt_btree_ops and related functions into dsl_scan.c as ext_size_ops.
Those functions are very small to worry about the code duplication and
range_tree does not need to know details such as rt_btree_compare.
- Instead of accounting number of pending bytes per pool, that needs
atomic on global variable per block, account the number of non-empty
per-vdev queues, that change much more rarely.
- When extent scan is interrupted by TXG end, continue it in the next
TXG instead of selecting next best extent. It allows to avoid leaving
one truncated (and so likely not the best any more) extent each TXG.
On top of some other optimizations this saves about 1.5 minutes out of
10 to scrub pool of 12 SSDs, storing 1.5TB of 4KB zvol blocks.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tom Caputi <caputit1@tcnj.edu>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#13576
Handle crypto_dispatch() return values same as crp->crp_etype errors.
On FreeBSD 12 many drivers returned same errors both ways, and lack
of proper handling for the first ended up in assertion panic later.
It was changed in FreeBSD 13, but there is no reason to not be safe.
While there, skip waiting for completion, including locking and
wakeup() call, for sessions on synchronous crypto drivers, such as
typical aesni and software.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#13563
During sorted scrub multiple threads (one per vdev) are issuing many
ZIOs same time, all using the same scn->scn_zio_root ZIO as parent.
It causes huge lock contention on the single global lock on that ZIO.
Improve it by introducing per-queue null ZIOs, children to that one,
and using them instead as proxy.
For 12 SSD pool storing 1.5TB of 4KB blocks on 80-core system this
dramatically reduces lock contention and reduces scrub time from 21
minutes down to 12.5, while actual read stages (not scan) are about
3x faster, reaching 100K blocks per second per vdev.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#13553
Modern Clang and GCC can successfully implement simple conditions
without branching with math and flag operations. Use of arrays for
translation no longer helps as much as it was 14+ years ago.
Disassemble of the code generated by Clang 13.0.0 on FreeBSD 13.1,
Clang 14.0.4 on FreeBSD 14 and GCC 10.2.1 on Debian 11 with this
change still shows no branching instructions.
Profiling of CPU-bound scan stage of sorted scrub shows reproducible
reduction of time spent inside avl_find() from 6.52% to 4.58%.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#13540
- Make prefetch distance adaptive: up to 4MB prefetch doubles for
every, hit same as before, but after that it grows by 1/8 every time
the prefetch read does not complete in time to satisfy the demand.
My tests show that 4MB is sufficient for wide NVMe pool to saturate
single reader thread at 2.5GB/s, while new 64MB maximum allows the
same thread to reach 1.5GB/s on wide HDD pool. Further distance
increase may increase speed even more, but less dramatic and with
higher latency.
- Allow early reuse of inactive prefetch streams: streams that never
saw hits can be reused immediately if there is a demand, while others
can be reused after 1s of inactivity, starting with the oldest. After
2s of inactivity streams are deleted to free resources same as before.
This allows by several times increase strided read performance on HDD
pool in presence of simultaneous random reads, previously filling the
zfetch_max_streams limit for seconds and so blocking most of prefetch.
- Always issue intermediate indirect block reads with SYNC priority.
Each of those reads if delayed for longer may delay up to 1024 other
block prefetches, that may be not good for wide pools.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#13452
When calculating mg_aliquot alike to #12046 use number of unique data
disks in the vdev, not the total number of children vdev. Increase
default value of the tunable from 512KB to 1MB to compensate.
Before this change each disk in striped pool was getting 512KB of
sequential data, in 2-wide mirror -- 1MB, in 3-wide RAIDZ1 -- 768KB.
After this change in all the cases each disk should get 1MB.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#13388
Previous flushing algorithm limited only total number of log blocks to
the minimum of 256K and 4x number of metaslabs in the pool. As result,
system with 1500 disks with 1000 metaslabs each, touching several new
metaslabs each TXG could grow spacemap log to huge size without much
benefits. We've observed one of such systems importing pool for about
45 minutes.
This patch improves the situation from five sides:
- By limiting maximum period for each metaslab to be flushed to 1000
TXGs, that effectively limits maximum number of per-TXG spacemap logs
to load to the same number.
- By making flushing more smooth via accounting number of metaslabs
that were touched after the last flush and actually need another flush,
not just ms_unflushed_txg bump.
- By applying zfs_unflushed_log_block_pct to the number of metaslabs
that were touched after the last flush, not all metaslabs in the pool.
- By aggressively prefetching per-TXG spacemap logs up to 16 TXGs in
advance, making log spacemap load process for wide HDD pool CPU-bound,
accelerating it by many times.
- By reducing zfs_unflushed_log_block_max from 256K to 128K, reducing
single-threaded by nature log processing time from ~10 to ~5 minutes.
As further optimization we could skip bumping ms_unflushed_txg for
metaslabs not touched since the last flush, but that would be an
incompatible change, requiring new pool feature.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12789
Use error thresholds from policy to control whether to scrub data
and/or metadata. If threshold is set to UINT64_MAX, then caller
probably does not care about result and we may skip that part.
By default import neither set the data error threshold nor read
the error counter, so skip the data scrub for faster import.
Metadata are still scrubbed and fail if even single error found.
While there just for symmetry return number of metadata errors in
case threshold is not set to zero and we haven't reached it.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#13022
The fnvlist versions of the functions are fatal if they fail,
saving each call from having to include checking the result.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Signed-off-by: Allan Jude <allan@klarasystems.com>
It is wrong for arc_write_ready() to use zfs_abd_scatter_enabled to
decide whether to reallocate/copy the buffer, because the answer is
OS-specific and depends on the buffer size. Instead of that use
abd_size_alloc_linear(), moved into public header.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#12425
The only reason for spa_config_*() to use refcount instead of simple
non-atomic (thanks to scl_lock) variable for scl_count is tracking,
hard disabled for the last 8 years. Switch to simple int scl_count
reduces the lock hold time by avoiding atomic, plus makes structure
fit into single cache line, reducing the locks contention.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12287
When scrubbing a raidz/draid pool, which contains a replacing or
sparing mirror with multiple online children, only one child will
be read. This is not normally a serious concern because the DTL
records are used to determine where a good copy of the data is.
As long as the data can be read from one child the mirror vdev
will use it to repair gaps in any of its children. Furthermore,
even if the data which was read is corrupt the raidz code will
detect this and issue its own repair I/O to correct the damage
in the mirror vdev.
However, in the scenario where the DTL is wrong due to silent
data corruption (say due to overwriting one child) and the scrub
happens to read from a child with good data, then the other damaged
mirror child will not be detected nor repaired.
While this is possible for both raidz and draid vdevs, it's most
pronounced when using draid. This is because by default the zed
will sequentially rebuild a draid pool to a distributed spare,
and the distributed spare half of the mirror is always preferred
since it delivers better performance. This means the damaged
half of the mirror will go undetected even after scrubbing.
For system administrations this behavior is non-intuitive and in
a worst case scenario could result in the only good copy of the
data being unknowingly detached from the mirror.
This change resolves the issue by reading all replacing/sparing
mirror children when scrubbing. When the BP isn't available for
verification, then compare the data buffers from each child. They
must all be identical, if not there's silent damage and an error
is returned to prompt the top-level vdev to issue a repair I/O to
rewrite the data on all of the mirror children. Since we can't
tell which child was wrong a checksum error is logged against the
replacing or sparing mirror vdev.
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13555
The zfs-load-module.service service is not currently provided by
the OpenZFS repository so we cannot safely assume it exists.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Thode <mthode@mthode.org>
Closes#13574
Since we use two B-trees q_exts_by_size and q_exts_by_addr, we should
count 2x sizeof (range_seg_gap_t) per node. And since average B-tree
memory efficiency is about 75%, we should increase it to 3x.
Previous code under-counted up to 30% of the memory usage.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#13537
I genuinely don't know why this didn't come up before,
but adding the LZ4 early abort pointed out this flaw,
in which we're allocating a buffer of one size, and
then telling the compressor that we're handing it buffers
of a different size, which may be Very Different - say,
allocating 512b and then telling it the inputs are 128k.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Amanakis <gamanakis@gmail.com>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#13375
It is typical, but not generally true that if log summary has more
blocks it must also have unflushed metaslabs. Normally with metaslabs
flushed in order it works, but there are known exceptions, such as
device removal or metaslab being loaded during its flush attempt.
Before 600a02b884 if spa_flush_metaslabs() hit loading metaslab it
usually stopped (unless memlimit is also exceeded), but now it may
flush more metaslabs, just skipping that particular one. This
increased chances of assertion to fire when the skipped metaslab is
flushed on next iteration if all other metaslabs in that summary
entry are already flushed out of order.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#13486Closes#13513
When a dataset is in the process of being received it gets marked as
inconsistent and should not be used. We should check for this when
opening a dataset handle in libzfs and return with an appropriate error
set, rather than hitting an abort because of the incomplete data.
zfs_open() passes errno to zfs_standard_error() after observing
make_dataset_handle() fail, which ends up aborting if errno is 0.
Set errno before returning where we know it has not been set already.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#13077
Make the wording more consistent for the kernel AC_MSG_CHECKING
output (e.g. "checking whether ...".). Additionally, group some
of the VFS interface checks with the others. No functional change.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Attila Fülöp <attila@fueloep.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13529
As of the Linux 5.19 kernel the asm/fpu/internal.h header was
entirely removed. It has been effectively empty since the 5.16
kernel and provides no required functionality.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Attila Fülöp <attila@fueloep.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13529
As of the Linux 5.19 kernel an identically named zap_flags_t typedef
is declared in the include/linux/mm_types.h linux header. Sadly,
the inclusion of this header cannot be easily avoided. To resolve
the conflict a #define is used to remap the name in the OpenZFS
sources when building against the Linux kernel.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13515
As of the Linux 5.19 kernel the disk_*_io_acct() helper functions
have been replaced by the bdev_*_io_acct() functions.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13515
As of the Linux 5.19 kernel the readpage() address space operation
has been replaced by read_folio().
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13515
Linux 5.19 commit torvalds/linux@44abff2c0 splits the secure
erase functionality from the blkdev_issue_discard() function.
The blkdev_issue_secure_erase() must now be issued to issue
a secure erase.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13515
Linux 5.19 commit torvalds/linux@44abff2c0 removed the
blk_queue_secure_erase() helper function. The preferred
interface is to now use the bdev_max_secure_erase_sectors()
function to check for discard support.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13515
Linux 5.19 commit torvalds/linux@70200574cc removed the
blk_queue_discard() helper function. The preferred interface
is to now use the bdev_max_discard_sectors() function to check
for discard support.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13515
As for the Linux 5.18 kernel bio_alloc() expects a block_device struct
as an argument. This removes the need for the bio_set_dev() compatibility
code for 5.18 and newer kernels.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13515
This was breaking the kmod port build on FreeBSD with Clang 13.
Use the same trick as we do for ASSERT() to make DNODE_VERIFY() use
its parameter at compile time without actually using it at run time
in non-debug builds.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#13507
Some minimal MUAs don't support passing the subjects as cmdline option.
This commit checks if "@SUBJECT@" is missing in ZED_EMAIL_OPTS and then
prepends a subject header to the notification message.
Also set a default for ${subject}.
Reviewed-by: Ahelenia Ziemia<C5><84>ska <nabijaczleweli@nabijaczleweli.xyz>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Daniel Hiepler <d-git@coderdu.de>
Closes#13440
Do not strip debug information from packages if '--enable-debuginfo' is
configured.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Umer Saleem <usaleem@ixsystems.com>
Closes#13500
Makes getmntent and getmntany thread-safe for external consumers of
libzfs zpool_disable_datasets, zfs_iter_mounted, libzfs_mnttab_update,
libzfs_mnttab_find.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#13484
This is a follow up to 3c35662299 which standardizes how the RHEL
version check is done. This simpler "0%{?rhel}" check is used
elsewhere in the packages so we do the same here.
Reviewed-by: Neal Gompa <ngompa@datto.com>
Reviewed-by: Rich Ercolani <rincebrain@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13501
When scrubbing/resilvering a pool it can be counter productive to
cancel the scan and kick of a replace operation to a hot spare
when encountering checksum errors. In this case, the best course
of action is to allow the scrub/resilver to complete as quickly
as possible and to keep the vdevs fully online if possible.
Realistically, this is less of an issue for a RAIDZ since a
traditional resilver must be used and checksums will be verified.
However, this is not the case for a mirror or dRAID pool which is
sequentially resilvered and checksum verification is deferred
until after the replace operation completes.
Regardless, we apply this policy to all pool types since it's
a good idea for all vdevs. Degrading additional vdevs has the
potential to make a bad situation worse. Note the checksum
errors will still be reported as both an event and by
`zpool status`. This change only prevents the ZED from
proactively taking any action.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13499
The SA attribute containing the symlink target does not include a nul
terminator, so when printing the target zdb would sometimes include
garbage at the end of the string.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#13482
- Replaced intances of `dracut_install` with `inst_simple`
- Removed calls to `test -x mark_hostonly` because the function is an
inbuilt dracut function
- Removed redundant installation of `systemd-ask-password` and
`systemd-tty-ask-password-agent` because they are already installed by
the systemd module. There is no need to install them again
- Removed multiple calls to the `mark_hostonly` function because the
`inst_simple` has a command-line switch for it
- Cleaned up the installation of the `zpool.cache`, `vdev_id.conf` and
`hostid` files to make the logic easier to follow
- Cleaned up and simplified the systemd service installation logic by
invoking systemctl instead of creating symlinks manually
- Replaced various hard-coded paths with dracut equivalents to better
conform with expected dracut behaviour
- Removed redundant call to `mkdir` (`inst_simple` creates the parent
directory if it does not exist on the destination initrd)
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Reviewed-by: Andrew J. Hesford <ajh@sideband.org>
Signed-off-by: Savyasachee Jha <hi@savyasacheejha.com>
Closes#13010
Since dracut functions can locate both udev rules and binaries, there is
no point in keeping absolute paths in the module setup script. It also
breaks the --sysroot option in dracut. This commit removes mentions to
absolute paths for binaries and udev rules.
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Reviewed-by: Andrew J. Hesford <ajh@sideband.org>
Signed-off-by: Savyasachee Jha <hi@savyasacheejha.com>
Closes#13010
Setting up the module involves multiple redundant calls to a bunch of
dracut functions wheich can be combined into one. Additionally, the mass
of code required to load libgcc_s.so* can be replaced with one dracut
function. This has the additional effect of removing errors involving
the non-installation of libgcc_s.so* which are seen on debian bullseye
when using version 2.1.2-1~bpo11+1 from the backports repository.
The systemd binaries are separated out into their own `dracut_install`
function call so they do not get pulled in when dracut does not load the
systemd module.
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Reviewed-by: Andrew J. Hesford <ajh@sideband.org>
Signed-off-by: Savyasachee Jha <hi@savyasacheejha.com>
Closes#13010
The compiler appears to be expanding the unused NULL pointer into a
zero-length array via the inline bitops code. When -Werror=array-bounds
is used, this causes a build failure. Recommended solution is allocate
temporary structures, fill with zeros (to avoid uninitialized data use
warnings), and pass the pointer to those to the inline calls.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#13463Closes#13465
Refcount creation for abd_zero_scatter->abd_children is redundant in
abd_alloc_zero_scatter, as it has been done in abd_init_struct.
In addition, abd_children is undefined when ZFS_DEBUG is disabled, the
reference of abd_children in abd_alloc_zero_scatter breaks build of
libzpool when ZFS_DEBUG is disabled.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Ping Huang <huangping@smartx.com>
Closes#13429
clang-15 emits the following error message for functions without
a prototype:
fs/zfs/os/linux/spl/spl-kmem-cache.c:1423:27: error:
a function declaration without a prototype is deprecated
in all versions of C [-Werror,-Wstrict-prototypes]
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Aidan Harris <me@aidanharr.is>
Closes#13421
Linux 5.12 PPC 5.12 get_user() and __copy_from_user_inatomic()
inline helpers very indirectly include a reference to the GPL'd
array mmu_feature_keys[] and fails to build. Workaround this by
using copy_from_user() and throwing EFAULT for any calls to
__copy_from_user_inatomic(). This is a workaround until a fix
for Linux commit 7613f5a66becfd0e43a0f34de8518695888f5458
"powerpc/64s/kuap: Use mmu_has_feature()" is fully addressed.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Authored-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: szubersk <szuberskidamian@gmail.com>
Closes#11958Closes#12590Closes#13367
On some architectures ZERO_PAGE is unavailable because it references
a GPL exported symbol of empty_zero_page. Originally e08b993 removed
the call to PAGE_ZERO(0) for assignment to the abd_zero_page. However,
a simple check can be done to avoid a kernel allocation and free for
the abd_zero_page if ZERO_PAGE is available.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Brian Atkinson <batkinson@lanl.gov>
Closes#13199
- Unconditionally inject `CONFIG_MODULES` make variable
and `#define CONFIG_MODULES` to Kbuild in `ZFS_LINUX_COMPILE`
autoconf function to emulate loadable kernel modules support.
This allows OpenZFS to perform Linux checks despite
`CONFIG_MODULES=n` in the actual Linux config.
- Add `ZFS_AC_KERNEL_CONFIG_MODULES` check which encompasses
the logic from `ZFS_AC_KERNEL_TEST_MODULE` with additional
diagnostic messages to the user
- Removed `ZFS_AC_KERNEL_TEST_MODULE` as it merely duplicates
every check in `ZFS_AC_KERNEL_CONFIG_DEFINED`
- Moved `ZFS_AC_MODULE_SYMVERS` after `ZFS_AC_KERNEL_CONFIG_DEFINED`
so the user has a chance to see the proper diagnostic from the
steps before.
A workaround for Linux's
```
commit 3e3005df73b535cb849cf4ec8075d6aa3c460f68
Author: Masahiro Yamada <masahiroy@kernel.org>
Date: Wed Mar 31 22:38:03 2021 +0900
kbuild: unify modules(_install) for in-tree and external modules
If you attempt to build or install modules ('make modules(_install)'
with CONFIG_MODULES disabled, you will get a clear error message, but
nothing for external module builds.
Factor out the modules and modules_install rules into the common part,
so you will get the same error message when you try to build external
modules with CONFIG_MODULES=n.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
```
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: szubersk <szuberskidamian@gmail.com>
Closes#10832Closes#13361
- Add `CONFIG_BLOCK` Linux config requirement to
`ZFS_AC_KERNEL_CONFIG_DEFINED`. OpenZFS won't compile without
that block device support due to large amount of functional
dependencies on it.
- Remove dependency on `groups_alloc()` in
`ZFS_AC_KERNEL_SRC_GROUP_INFO_GID` to circumvent the missing stub
in Linux 4.X kernel headers.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: szubersk <szuberskidamian@gmail.com>
Closes#13351
This adds supports for hole-punching facilities in the FreeBSD kernel
starting from __FreeBSD_version 1400032.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Ka Ho Ng <khng@FreeBSD.org>
Sponsored-by: The FreeBSD Foundation
Closes#12458
Holding a dbuf is a common operation which can become highly contended
in dbuf_find() when acquiring the dbuf hash mutex. This is particularly
true on Linux when reading/writing volumes since by default up to 32
threads from the zvol_taskq may be taking a hold of the same dbuf.
This should also be observable on FreeBSD as long as there are enough
processes accessing the volume concurrently.
This is further aggregrated by the fact that only the block id will
be unique when calculating the dbuf hash for a single volume. The
objset id, object id, and level will be the same for data blocks.
This has been observed to result in a somehwat less than uniform hash
distribution and a longer than expected max hash chain depth (~20)
on a large memory system (256 GB) using volumes.
This commit improves the siutation by switching the hash mutex to
an rwlock to allow concurrent lookups, and increasing DBUF_RWLOCKS
from 2048 to 8192 to further reduce the odds of a hash collision.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13405
Thorough documentation with a dracut.bootup(7)-style flowchart,
dracut.cmdline(7)-style cmdline listing,
and per-file docs like the old README
Upstream-commit: e3fc330d6c
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13291
So far, everything parsed root= manually, which meant that while
zfs-parse.sh was updated, and supposedly supported + -> ' ' conversion,
it meant nothing
Instead, centralise parsing, and allow:
root=
root=zfs
root=zfs:
root=zfs:AUTO
root=ZFS=data/set
root=zfs:data/set
root=zfs:ZFS=data/set (as a side-effect; allowed but undocumented)
rootfstype=zfs AND root=data/set <=> root=data/set
rootfstype=zfs AND root= <=> root=zfs:AUTO
So rootfstype=zfs /also/ behaves as expected, and + decoding works
Upstream-commit: 245529d85f
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13291
It was added in the original ae26d0465a ("Add dracut support") commit
in 2011, and was then broken a bit later with the advent of
dracut-zfs-generator, or maybe earlier as part of other churn
Either way, it's broken, and has been in 2.0+ as well, and no-one
complained. Stop pretending we support it at all
Upstream-commit: 2c74617bcf
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13291
There was a fallback case I overlooked in the initial patch, with
a similarly imperfect version extractor.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12045Closes#12673
Clang 13.0.0 added support for `Wunused-but-set-parameter` and
`-Wunused-but-set-variable` which correctly detects two unused
variables in zstd resulting in a build failure. This commit
annotates these instances accordingly.
https://releases.llvm.org/13.0.1/tools/clang/docs/ReleaseNotes.html#id6
In FSE_createCTable(), malloc() is intentionally defined as NULL when
compiled in the kernel so the variable is unused.
zstd/lib/compress/fse_compress.c:307:12: error: variable 'size'
set but not used [-Werror,-Wunused-but-set-variable]
Additionally, in ZSTD_seqDecompressedSize() the assert is compiled
out similarly resulting in an unused variable.
zstd/lib/compress/zstd_compress_superblock.c:412:12: error: variable
'litLengthSum' set but not used [-Werror,-Wunused-but-set-variable]
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
The only zdb utility require to read metaslab-related data during
read-only pool import because of spacemaps validation. Add global
variable which will allow zdb read spacemaps in case of readonly
import mode.
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Fedor Uporov <fuporov.vstack@gmail.com>
Closes#9095Closes#12687
When using a Linux kernel which predates the iov_iter interface the
O_APPEND flag should be applied in zpl_aio_write() via the call to
generic_write_checks(). The updated pos variable was incorrectly
ignored resulting in the current offset being used.
This issue should only realistically impact the RHEL/CentOS 7.x
kernels which are based on Linux 3.10.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13370Closes#13377
In hypothetical case of non-linear ABD with single segment, multiple
to page size but not aligned to it, vdev_geom_fill_unmap_cb() could
fill one page less into bio_ma array.
I am not sure it is expoitable, but better to be safe than sorry.
Reported-by: Mark Johnston <markj@FreeBSD.org>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
(cherry picked from commit 5352f85cddce44e82fb1c4caec3b333e3666d7fd)
It turns out, no, in fact, ZERO_RANGE and PUNCH_HOLE do
have differing semantics in some ways - in particular,
one requires KEEP_SIZE, and the other does not.
Also added a zero-range test to catch this, corrected a flaw
that made the punch-hole test succeed vacuously, and a typo
in file_write.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#13329Closes#13338
As of the 5.17 kernel the GENHD_FL_EXT_DEVT flag has been removed
and the GENHD_FL_NO_PART_SCAN flag renamed GENHD_FL_NO_PART. Update
zvol_alloc() to set GENHD_FL_NO_PART for the newer kernels which
is sufficient. The behavior for prior kernels remains unchanged.
1ebe2e5f ("block: remove GENHD_FL_EXT_DEVT")
46e7eac6 ("block: rename GENHD_FL_NO_PART_SCAN to GENHD_FL_NO_PART")
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13294Closes#13297
FreeBSD's memory management system uses its own error numbers and gets
confused when these VOPs return EIO.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reported-by: Peter Holm <pho@FreeBSD.org>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#13311
For legacy reasons, a couple of VOPs have to return error numbers that
don't come from the usual errno namespace. To handle the cases where
ZFS_ENTER or ZFS_VERIFY_ZP fail, we need to be able to override the
default error return value of EIO. Extend the macros to permit this.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#13311
->readpages was removed and replaced by ->readahead. Define
zpl_readahead for kernels that don't have ->readpages.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Riccardo Schirone <rschirone91@gmail.com>
Closes#13278
blkdev.h includes genhd.h since dawn of upstream git, so this is
globally safe
Upstream-commit: 322cbb50de711814c42fb088f6d31901502c711a ("block:
remove genhd.h")
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13251
bio_alloc(gfp_t gfp_mask, unsigned short nr_iovecs)
became
bio_alloc(struct block_device *bdev, unsigned short nr_vecs,
unsigned int opf, gfp_t gfp_mask)
passing NULL/0 continues previous behaviour
Upstream-commit: 07888c665b405b1cd3577ddebfeb74f4717a84c4 ("block:
pass a block_device and opf to bio_alloc")
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13251
NDF_ONLY_PNBUF has been removed from FreeBSD in favor of NDFREE_PNBUF.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#13277
Lustre makes light use of the zfs_refcount interfaces which
isn't a problem when using a non-debug build of OpenZFS. However,
when debugging is enabled the required symbols are not exported.
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12613
Strict hole reporting was previously disabled by default as a
performance optimization. However, this has lead to confusion
over the expected behavior and a variety of workarounds being
adopted by consumers of ZFS. Change the default behavior to
always report holes and force the TXG sync.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Upstream-commit: 05b3eb6d23
Ref: #13261Closes#12746
* etc/systemd/zfs-mount-generator: serialise
The wins for a relatively normal workload are rather slim:
real 0.02119s/0.00985s=2.15029x
user 0.02130s/0.00346s=6.15560x
sys 0.03858s/0.00643s=6.00062x
wall-total 0.014518s/0.005925s=2.45009x
wall-init 0.014518s/0.002457s=5.90684x
wall-real 0.014518s/0.003467s=4.18668x
But this is a big win on machines with a lot of datasets and expensive
forks.
For example, the gain on a VM on my work laptop with 900+ legacy-mount
Docker datasets, the original gains from the C rewrite were
only five-fold:
real 0.516s/0.102s=5.05882x
user 0.237s/0.143s=1.65734x
sys 0.287s/0.100s=2.87x
And this serial variant gains this back there as well:
real 0.102s/0.008s=12.75x
user 0.143s/0.007s=20.42857
sys 0.100s/0.001s=100x
wall-total 0.09717s/0.00319s=30.40255x
wall-init 0.00203s/0.00200s=1.015941x
wall-real 0.09513s/0.00118s=80.02043x
For a total of
real 0.516s/0.008s=64.5x
user 0.237s/0.007s=33.85714x
sys 0.287s/0.001s=287x
Suggested-by: Richard Laager <rlaager@wiktel.com>
* etc/systemd/zfs-mount-generator: pull in network for keylocation=https
Also simplify RequiresMountsFor= handling
Ref: #11956
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Upstream-commit: 4325de09cdCloses#12138
A prior commit included a udev check for MPATH_DEVICE_READY to
determine if a path was multipath when doing an autoreplace:
f2f6c18 zed: Misc multipath autoreplace fixes
However, MPATH_DEVICE_READY is not provided by the older version of
udev that's on Centos 7 (it is on Centos 8).
This patch instead looks for 'mpath-' in the UUID, which works on
both Centos 7 and 8.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#13222
We recently had a case where our operators replaced a bad
multipathed disk, only to see it fail to autoreplace. The
zed logs showed that the multipath replacement disk did not pass
the 'is_dm' test in zfs_process_add() even though it should have.
is_dm is set if there exists a sysfs entry for to the
underlying /dev/sd* paths for the multipath disk. It's
possible this path didn't exist due to a race condition where
the sysfs paths weren't created at the time the udev event came
in to zed, but this was never verified.
This patch updates the check to look for udev properties that
indicate if the new autoreplace disk is an empty multipath disk,
rather than looking for the underlying sysfs entries. It also
adds in additional logging, and fixes a bug where zed allowed
you to use an already zfs-formatted disk from another pool
as a multipath auto-replacement disk.
Furthermore, while testing this patch, I also ran across a case
where a force-faulted disk did not have a ZPOOL_CONFIG_PHYS_PATH
entry in its config. This prevented it from being autoreplaced.
I added additional logic to derive the PHYS_PATH from the PATH if
the PATH was a /dev/disk/by-vdev/ path. For example, if PATH
was /dev/disk/by-vdev/L28, then PHYS_PATH would be L28. This is
safe since by-vdev paths represent physical locations and do not
change between boots.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#13023
This PR changes ZFS ACL checks to evaluate
fsuid / fsgid rather than euid / egid to avoid
accidentally granting elevated permissions to
NFS clients.
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Andrew Walker <awalker@ixsystems.com>
Co-authored-by: Ryan Moeller <freqlabs@FreeBSD.org>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#13221
Commit 3b52ccd7d introduced a flaw where FSR and FSAVE are not restored
when using a Linux 5.16 kernel. These instructions are only used when
XSAVE is not supported by the processor meaning only some systems will
encounter this issue.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Attila Fülöp <attila@fueloep.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13210Closes#13236
At shutdown time, we drain all of the zevents and set the
ZEVENT_SHUTDOWN flag. On FreeBSD, we may end up calling
zfs_zevent_destroy() after the zevent_lock has been destroyed while
the sysevent thread is winding down; we observe ESHUTDOWN, then back
out.
Events have already been drained, so just inline the kmem_free call in
sysevent_worker() to avoid the race, and document the assumption that
zfs_zevent_destroy doesn't do anything else useful at that point.
This fixes a panic that can occur at module unload time.
Reviewed-by: Ryan Moeller <freqlabs@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Kyle Evans <kevans@FreeBSD.org>
Closes#13220
The get_key_material_https() function error code path had a bogus
free() call, either resulting in double-free or free() of undefined
pointer.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ahelenia Ziemia<C5><84>ska <nabijaczleweli@nabijaczleweli.xyz>
Co-authored-by: Harry Sintonen <sintonen@iki.fi>
Signed-off-by: Harry Sintonen <sintonen@iki.fi>
Closes#13198
This is a direct commit to zfs-2.1-release to fix release builds that
error out on an unused variable. The issue is avoided on master by a
huge series of commits that change how the ASSERT macros work, but that
is not feasible to backport.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#13194Closes#13196
When unlinking multiple files from a pool at 100% capacity, it was
possible for ENOSPC to be returned after the first unlink. e.g.
rm -f /mnt/fs/test1.0.0 /mnt/fs/test1.1.0 /mnt/fs/test1.2.0
rm: cannot remove '/mnt/fs/test1.1.0': No space left on device
rm: cannot remove '/mnt/fs/test1.2.0': No space left on device
After waiting for the pending deferred frees from the first unlink to
be processed the remaining files can then be unlinked. This is caused
by the quota limit in dsl_dir_tempreserve_impl() being temporarily
decreased to the allocatable pool capacity less any deferred free
space.
This is resolved using the existing mechanism of returning ERESTART
when over quota as long as we know enough space will shortly be
available after processing the pending deferred frees.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <freqlabs@FreeBSD.org>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13172
In the CI environment it's possible for events to be slightly
delayed resulting in 4, instead of 5, events appearing in the
log file. This isn't a problem and should be considered a
success to avoid false positive test results.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12625
When rolling back a dataset, ZFS has to purge file data resident in the
system page cache. To do this, it loops over all vnodes for the
mountpoint and calls vn_pages_remove() to purge pages associated with
the vnode's VM object. Each page is thus exclusively busied while the
dataset's teardown write lock is held.
When handling a page fault on a mapped ZFS file, FreeBSD's page fault
handler busies newly allocated pages and then uses VOP_GETPAGES to fill
them. The ZFS getpages VOP acquires the teardown read lock with vnode
pages already busied. This represents a lock order reversal which can
lead to deadlock.
To break the deadlock, observe that zfs_rezget() need only purge those
pages marked valid, and that pages busied by the page fault handler are,
by definition, invalid. Furthermore, ZFS pages always transition from
invalid to valid with the teardown lock held, and ZFS never creates
partially valid pages. Thus, zfs_rezget() can use the new
vn_pages_remove_valid() to skip over pages busied by the fault handler.
PR: 258208
Tested by: pho
Reviewed by: avg, sef, kib
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D32931
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#12828
While switching abd_zero_buf allocation KPI I've missed the fact
that kmem_zalloc() zeroed the allocation, while kmem_cache_alloc()
does not. Add explicit bzero() after it.
I don't think it should have caused real problems, but leaking one
memory page content all over the pool is not good.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#12569
Related to commit 90b77a036. Retry the `zpool export` if the pool
is "busy" indicating there is a process accessing the mount point.
This can happen after an import, allowing it to be retried will
avoid spurious test failures.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13169
As explained by the disclaimer in the test case,
"This test can fail since nothing guarantees that old
MOS blocks aren't overwritten."
This behavior is expected and correct, but results in a
flaky test case which is problematic for the CI. The best
we can do to resolve this is to retry the sub-test which
failed when the MOS blocks have clearly been overwritten.
When testing failures were rare enough that a single retry
should normally be sufficient. However, we allow up to
five for good measure.
Reviewed by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13119
As previously noted in #12272 the receive-o-x_props_override.ksh test
reliably fails on FreeBSD. Since we don't expect this test to pass
move the exception from the "maybe" to "known" section. This way we
don't retry the FAILED test when it is not expected to pass.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Ryan Moeller <freqlabs@FreeBSD.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13167
On FreeBSD pools are not allowed to be created using vdevs which are
backed by ZFS volumes. This configuration is not recommended for any
supported platform, nevertheless the largest_pool_001_pos.ksh test
case makes use of it as a convenience. This causes the test case to
fail reliably on FreeBSD. The layout is still tolerated on Linux
so only perform this test on Linux.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Ryan Moeller <freqlabs@FreeBSD.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13166
We move the spinlock unlock before the thread creation. This should be
safe because the thread creation code doesn't actually manipulate any
taskq data structures; that's done by the thread once it's created.
We also remove the assertion that the maxthreads is the current threads
plus one; that assertion could fail if multiple hotplug events come in
quick succession, and the first new taskq thread hasn't had a chance to
start processing yet.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
eviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#12714
Linux 5.11 changed kernel_fpu_begin() to an inlined function and
moved the functionality to kernel_fpu_begin_mask(). This breaks the
existing detection mechanism since it checks if kernel_fpu_begin is
an exported kernel symbol, which isn't the case for an inlined
function.
To avoid assumptions about internal implementation, replace
ZFS_LINUX_TEST_RESULT_SYMBOL in favor of ZFS_LINUX_TEST_RESULT
which already makes sure kernel_fpu_{begin,end}() is usable by us.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Attila Fülöp <attila@fueloep.org>
Closes#13147
Most modern Linux distributions have separate locations for bare
source and prebuilt ("build") files. Additionally, there are `source`
and `build` symlinks in `/lib/modules/$(KERNEL_VERSION)` pointing to
them. The order of directory search is now:
- `configure` command line values if both `--with-linux` and
`--with-linux-obj` were defined
- If only `--with-linux` was defined, `--with-linux-obj` is assumed
to have the same value as `--with-linux`
- If neither `--with-linux` nor `--with-linux-obj` were defined
autodetection is used:
- `/lib/modules/$(uname -r)/{source,build}` respectively, if exist
- The first directory in `/lib/modules` with the highest version
number according to `sort -V` which contains `source` and `build`
symlinks/directories
- The first directory matching `/usr/src/kernels/*` and
`/usr/src/linux-*` with the highest version number according to
`sort -V`. Here the source and prebuilt directories are assumed
to be the same.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: szubersk <szuberskidamian@gmail.com>
Closes#9935Closes#13096
Raw sending from pool1/encrypted with ashift=9 to pool2/encrypted with
ashift=12 results to failure when mounting pool2/encrypted (Input/Output
error). Notably, the opposite, raw sending from a greater ashift to a
lower one does not fail.
This happens because zio_compress_write() falsely checks only
ZIO_FLAG_RAW_COMPRESS and not ZIO_FLAG_RAW_ENCRYPT which is also set in
encrypted raw send streams. In this case it rounds up the psize and if
not equal to the zio->io_size it modifies the block by zeroing out
the extra bytes. Because this happens in a SA attr. registration object
(type=46), the decryption fails upon mounting the filesystem, and zpool
status falsely reports an error.
Fix this by checking both ZIO_FLAG_RAW_COMPRESS and ZIO_FLAG_RAW_ENCRYPT
before deciding whether to zero-pad a block.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#13067Closes#13074
There are two codepaths than can dirty final TXGs:
1) If calling spa_export_common()->spa_unload()->
spa_unload_log_sm_flush_all() after the spa_final_txg is set, then
spa_sync()->spa_flush_metaslabs() may end up dirtying the final
TXGs. Then we have the following panic:
Call Trace:
<TASK>
dump_stack_lvl+0x46/0x62
spl_panic+0xea/0x102 [spl]
dbuf_dirty+0xcd6/0x11b0 [zfs]
zap_lockdir_impl+0x321/0x590 [zfs]
zap_lockdir+0xed/0x150 [zfs]
zap_update+0x69/0x250 [zfs]
feature_sync+0x5f/0x190 [zfs]
space_map_alloc+0x83/0xc0 [zfs]
spa_generate_syncing_log_sm+0x10b/0x2f0 [zfs]
spa_flush_metaslabs+0xb2/0x350 [zfs]
spa_sync_iterate_to_convergence+0x15a/0x320 [zfs]
spa_sync+0x2e0/0x840 [zfs]
txg_sync_thread+0x2b1/0x3f0 [zfs]
thread_generic_wrapper+0x62/0xa0 [spl]
kthread+0x127/0x150
ret_from_fork+0x22/0x30
</TASK>
2) Calling vdev_*_stop_all() for a second time in spa_unload() after
spa_export_common() unnecessarily delays the final TXGs beyond what
spa_final_txg is set at.
Fix this by performing the check and call for
spa_unload_log_sm_flush_all() before the spa_final_txg is set in
spa_export_common(). Also check if the spa_final_txg has already been
set in spa_unload() and skip those calls in this case.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
External-issue: https://www.illumos.org/issues/9081Closes#13048Closes#13098
All of these externs are already #included as static inline
functions via corresponding headers.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@gmail.com>
Closes#13073
Related to commit 90b77a036. Retry the `zpool export` if the pool is
"busy" indicating there is a process accessing the mount point. This
can happen after an import and allowing it to be retried will avoid
spurious test failures.
Reviewed by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13092
The dRAID section of the zpool_expand_001_pos test would reliably fail
because the calculated expansion size assumed the dRAID top-level vdev
was created with a distributed spare. Create the vdev as expected to
resolve the test failure.
This test case flaw was accidentally caused by changing the default
number of dRAID distributed spares from one to zero while dRAID was
being developed.
Additionally, remove zpool_expand_005_pos from the list of possible
faulty tests. It appears to be passing consistently in my testing.
Reviewed by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13091
Observed when building on CentOS 8 Stream. Remove the `out`
label at the end of the function and instead return.
linux/simd_x86.h: In function 'kfpu_begin':
linux/simd_x86.h:337:1: error: label at end of compound statement
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Attila Fülöp <attila@fueloep.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13089
It's noted very scarcely in the code as it stands, indeed the only
actual comment on this is
/*
* We have finished background destroying, but there is still
* some space left in the dp_free_dir. Transfer this leaked
* space to the dp_leak_dir.
*/
Introduced in fbeddd60b7 ("Illumos 4390 -
I/O errors can corrupt space map when deleting fs/vol"),
which explains, alongside the references, that this can only happen
with a corrupted pool
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13081
Should be `-o keyformat=passphrase` instead of `-o -keyformat=passphrase`
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chuang Zhu <chuang@melty.land>
Closes#13072
Changing volmode may need to remove minors, which could be open, so
call udev_wait() before we "zfs set volmode=<value>". This ensures
no udev process has the zvol open (i.e. blkid) and the kernel
zvol_remove_minor_impl() function won't skip removing the in use
device.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13075
This allows reads/writes caused by accesses to mmap files to be
accounted correctly in the per-dataset kstats for both Linux and
FreeBSD.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <freqlabs@FreeBSD.org>
Signed-off-by: Matthias Blankertz <matthias@blankertz.org>
Closes#12994Closes#13044
dmu_recv_begin_check() unconditionally sets the DS_HOLD_FLAG_DECRYPT
flag before calling dsl_dataset_hold_flags(). If the key on the
receiving side isn't loaded or the send stream contains embedded
blocks, the receive check fails for a stream which is perfectly
valid and could be received without any problem. This seems like
a remnant of the initial design, where unencrypted datasets below
encrypted ones weren't allowed.
Add a condition to set `DS_HOLD_FLAG_DECRYPT` only for encrypted
datasets, modify an existing test to detect this regression and add
a test for raw replication streams.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Amanakis <gamanakis@gmail.com>
Co-authored-by: George Amanakis <gamanakis@gmail.com>
Signed-off-by: Attila Fülöp <attila@fueloep.org>
Closes#13033Closes#13076
Currently, $(CC), $(LD), and $(LLVM) variables aren't passed to kbuild
while building modules. This causes modules to build with the default
GNU GCC toolchain and prevents experimenting with other toolchains such
as CLANG/LLVM. It can also lead to build failure if the CFLAGS/LDFLAGS
passed are incompatible with gcc/ld.
Pass $KERNEL_CC, $KERNEL_LD, and $KERNEL_LLVM as $(CC), $(LD), and
$(LLVM), respectively, to kbuild for each that is defined in the
environment. This should take care of the majority of alternative
toolchain use cases.
Reviewed-by: Damian Szuberski <szuberskidamian@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Peter Levine <plevine457@gmail.com>
Closes#13046
Linux 5.16 moved XSTATE_XSAVE and XSTATE_XRESTORE out of our reach,
so add our own XSAVE{,OPT,S} code and use it for Linux 5.16.
Please note that this differs from previous behavior in that it
won't handle exceptions created by XSAVE an XRSTOR. This is sensible
for three reasons.
- Exceptions during XSAVE and XRSTOR can only occur if the feature
is not supported or enabled or the memory operand isn't aligned
on a 64 byte boundary. If this happens something else went
terribly wrong, and it may be better to stop execution.
- Previously we just printed a warning and didn't handle the fault,
this is arguable for the above reason.
- All other *SAVE instruction also don't handle exceptions, so this
at least aligns behavior.
Finally add a test to catch such a regression in the future.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Attila Fülöp <attila@fueloep.org>
Closes#13042Closes#13059
Using `zfs_mount_at()` gives opportunity to properly propagate
mountopts from what's stored in a pool to the `mount(2)` syscall
invocation. It fixes cases when mount options are set to incorrect
values and rectification is impossible (e. g. Linux initrd boot
sequence in #7947).
Moved debug information printing after all variables are
initialized - printed text reflects what is passed to `mount(2)`.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: szubersk <szuberskidamian@gmail.com>
Issue #7947Closes#13021
Bullseye shellcheck picks these up as SC2140, and it's right!
@LIBFETCH_SONAME@ is already quoted, so dracut had
"$d/"libcurl.so.4""
and i-t had
""libcurl.so.4""
Partially reverts 34eef3e9a7 (#12760),
which broke this
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12835
The on-disk cost of creating a snapshot or bookmark is sufficiently low
that it is difficult to make it reliably fail even when the pool is
"full". In order to avoid false positives remove these two checks from
the test case.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13060
POSIX requires that set-uid and set-gid bits to be removed when an
unprivileged user writes to a file and ZFS does that during normal
operation.
The problem arrises when the write is stored in the ZIL and replayed.
During replay we have no access to original credentials of the process
doing the write, so zfs_write() will be performed with the root
credentials. When root is doing the write set-uid and set-gid bits
are not removed from the file.
To correct that, log a separate TX_SETATTR entry that removed those bits
on first write to such file.
Idea from: Christian Schwarz
Add test for ZIL replay of setuid/setgid clearing.
Improve various edge cases when clearing setid bits:
- The setid bits can be readded during a single write, so make sure to check
for them on every chunk write.
- Log TX_SETATTR record at most once per transaction group (if the setid bits
are keep coming back).
- Move zfs_log_setattr() outside of zp->z_acl_lock.
Reviewed-by: Dan McDonald <danmcd@joyent.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Christian Schwarz <me@cschwarz.com>
Signed-off-by: Pawel Jakub Dawidek <pawel@dawidek.net>
Closes#13027
This commit adds enumerated names to disambiguate between the
different vdevs. Previously only 'zpool status' showed enumerated
vdev names, now 'zpool list -v' and 'zpool iostat -v' also shows
the enumerated vdev names.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Dipak Ghosh <dipak.ghosh@hpe.com>
Signed-off-by: Akash B <akash-b@hpe.com>
Closes#12510Closes#13031
In files created/modified before 4254acb there may be a corruption of
xattrs which is not reported during scrub and normal send/receive. It
manifests only as an error when raw sending/receiving. This happens
because currently only the raw receive path checks for discrepancies
between the dnode bonus length and the spill pointer flag.
In case we encounter a dnode whose bonus length is greater than the
predicted one, we should report an error. Modify in this regard
dnode_sync() with an assertion at the end, dump_dnode() to error out,
dsl_scan_recurse() to report errors during a scrub, and zstream to
report a warning when dumping. Also added a test to verify spill blocks
are sent correctly in a raw send.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#12720Closes#13014
When the optional PAM binaries are included in a build, ./configure will
look for security/pam_modules.h and - if it doesn't find it - recommend
the user install `libpam0g-dev`. On Red Hat systems, `pam-devel` is the
package that supplies this requirement; `libpam0g-dev` does not exist.
By encoding this requirement in the spec file, we give packagers more
appropriate (and timely) recommendations for completing the build.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chris Lindee <chris.lindee+github@gmail.com>
Closes#13001
Nowhere in the description of the failmode property does it
clearly state how to bring a suspended pool back online.
Add a few words to property description and the zpool-clear(8)
man page.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12907Closes#9395
This change is to first replace the OpenZFS website in the README to
point to openzfs.org as this is what open-zfs.org redirects to.
Along with replacing the URL, the protocol is also upgraded
from http to https.
These changes should prevent web browsers such as Firefox from
complaining about visiting a http site, if the proper security
settings are enabled, when it will still end up on a https page
after the redirect.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Hirasaki <ryanhirasaki@gmail.com>
Closes#12939
This is a follow up commit for e03a41a60 which aimed to resolve
this same test failure. The core "problem" here is that it takes
very little space to perform a clone/snapshot/bookmark, which
means if we want these commands to reliably fail the pool must
truely have exhausted all free space.
This commit increases the number of fill iterations to try and
consume every block which we can. This still can't guarantee
the clone/snapshot/bookmark will fail, but it significantly
improves the odds. The exception was kept since it's still
not a sure thing.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12903
Under Linux when rolling back a mounted filesystem negative dentries
may not be dropped from the cache. This can result in an ENOENT
being incorrectly returned on first access. Issuing a `df` before
the unmount results in the negative dentries being invalidated and
side steps the issue.
This is solely a workaround for the test case on Linux and not
correct behavior. The core issue of invalidating negative dentries
needs to be handled with a kernel side change. This is being
tracked as issue #6143.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12898
Issue #6143
The following test cases may still occasionally fail and are being
added to the "maybe" list for Linux until they can be updated to be
entirely reliable.
cli_root/zfs_rename/zfs_rename_002_pos.ksh
cli_root/zpool_reopen/zpool_reopen_003_pos.ksh
refreserv/refreserv_raidz
These 6 tests consistently fail only on Fedora 31+, the failures
are related to the kernel rescanning the partition table on loopback
devices which is no longer reliable unless partprobe is used. In
order to enable the Fedora bot by default they are also being added
to the list until the tests can be updated. Any significant regression
in functionality covered by these tests will still be detected by the
FreeBSD builders.
alloc_class/alloc_class_009_pos
alloc_class/alloc_class_010_pos
cli_root/zpool_expand/zpool_expand_001_pos
cli_root/zpool_expand/zpool_expand_005_pos
rsend/rsend_007_pos
rsend/rsend_010_pos
rsend/rsend_011_pos
snapshot/rollback_003_pos
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#10489
It keeps failing, on changes which aren't related at all.
So until someone runs down why, I'd like it to stop being the
sole reason for CI failures.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12733
Add the following test failures to the exception list for FreeBSD
to ensure we notice new unexpected failures.
pool_checkpoint/checkpoint_big_rewind
pool_checkpoint/checkpoint_indirect
And the following for Linux.
zvol/zvol_misc/zvol_misc_snapdev
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #12621
Issue #12622
Issue #12623Closes#12624
The zvol_misc tests, in particular zvol_misc_volmode, make use of a
common udev_wait function to wait for zvol devices in /dev to quiesce
on Linux. On other platforms this function currently only sleeps for
one second before returning. This is insufficient, and
zvol_misc_volmode has been flaky on FreeBSD as a result.
Replace udev_wait with block_device_wait, passing through the optional
device parameter where possible. Rearrange a few checks to strengthen
the verifications we are making and avoid unnecessarily sleeping. We
must keep udev_wait in a couple places to pass in Github CI workflows.
Remove zvol_misc_volmode from the maybe failing tests on FreeBSD in
zts-report.py.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#12583
The rerefreserv_raidz test was failing on Linux because the sync being
issued doesn't guarantee a pool sync. Switch to using the sync_pool
function and remove the ZTS exception for Linux.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12897
The build on musl needs linux/fs.h for SEEK_DATA and friends,
and sys/sysmacros.h for P2ROUNDUP. Add the needed headers.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Georgy Yakovlev <gyakovlev@gentoo.org>
Closes#12891
With some minor tweaks several of rsend tests can be sped up
considerably without significantly reducing test coverage.
* send-c_verify_ratio: ~120s -> ~60s
* send_realloc_*_files: ~330s -> ~65s
For the send_realloc* tests this also has the advantage of removing
(most of) the linux/freebsd conditional logic. Note that for this
test more passes, and thus more incremental send/recvs, are preferable
to a larger number of files.
Total run time of the rsend test group was reduced from roughly 20 to
11 minutes in an environment similar to what's used by the CI.
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12876
The rsend_007_pos test reliably fails on Linux in the cleanup
function. This is caused by an unmount error when attempting to
recursively destroy the newly received datasets. Invoking `df`
prior to the `zfs destroy` interestingly avoids the unmont error.
Why this should matter is unclear and should be investigated.
However, this minor tweak may allow us to remove the ZTS rsend
exceptions. The subsequent rsend_010_pos and rsend_011_pos
failures were a result of this initial failure. The other
"maybe" failures I was unable to reproduce and have not been
recently observed in the master branch.
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#5665Closes#6086Closes#6087Closes#6446Closes#12876
This change primarily seeks to make implicit documentation explicit, as
it is not outright stated that options should be comma-separated, nor is
there a reason given for it.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Daniel Ebdrup Jensen <debdrup@FreeBSD.org>
Closes#12579
If we die from timeout of the whole GH action run, we don't run the
collect step afterward, which can make it hard to investigate the
timeout.
If we timeout first in the test action, though, it qualifies as
failure, and collects appropriately.
(330 minutes seems like an acceptable tradeoff between the 6h
timeout by default on the action and the 4h and change "functional"
usually takes.)
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12999
Debian ships fake System.map files by default, leading to the
invocation of depmod with them to flood you with errors about
missing symbols.
Let's notice and not do that.
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12862
The alloc_class_* tests may fail on Linux with an EBUSY error if
`zfs destroy` is run before the `dd` process has had a chance to
terminate. Wait on the pid after the `kill -9` to make sure.
When testing I didn't observe any failures for the alloc_class
tests. Remove them from the exceptions list, the CI was used to
verify the tests pass on all platforms.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Rich Ercolani <rincebrain@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12873
Unfortunately, #11445 means while we fail gracefully now, we still
fail, unless people want to implement a complex workaround just to
support /dev/null.
So let's just use the cheap workaround in a test for now.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12872
The zpool_reopen_[1-5] tests are failing Fedora 35 with:
zpool_reopen_001_pos.ksh[64]: log_must[67]: log_pos[270]:
wait_for_resilver_end[98]: wait_for_action: line 71: func: is read only
Renaming 'func' -> 'funct' fixes the issue.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#12871
`UNAVAIL` is maybe not quite as concerning as `DEGRADED`, but still an
event of notice, in my opinion. For example it is triggered when a
drive goes missing.
Reviewed-by: Don Brady <don.brady@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Francesco Mazzoli <f@mazzo.li>
Closes#12629Closes#12630
For kernel to send snapshot mount/unmount events to zed.
For kernel to send symlink creates/removes on zvol plumbing.
(/dev/run/dsk/zvol/$pool/$zvol -> /dev/diskX)
If zed misses the ENODEV, all errors after are EINVAL. Treat any error
as kernel module failure.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Closes#12416
This was discovered when using Discords Slack compatible webhook.
Slack webhooks works without the escape, however Discord rightly refuses
the POST as it contains invalid JSON.
https://discord.com/developers/docs/resources/webhook#execute-slackcompatible-webhook
Valid (while escaping the newline:
```
+ msg_json='{"text": "*ZFS scrub_finish error for test on quartz*\nZFS has detected a data error:\n\n eid: 124\n class: scrub_finish\n host: quartz\n time: \n error: \n objid: :\n pool: test\n"}'
```
Invalid (no escape):
```
+ msg_json='{"text": "*ZFS scrub_finish error for test on quartz*
ZFS has detected a data error:\n\n eid: 124\n class: scrub_finish\n host: quartz\n time: \n error: \n objid: :\n pool: test\n"}'
```
The new line gets rendered and not sent inside the JSON as intended.
```
++ curl -X POST https://discord.com/api/webhooks/{webhook.id}/{webhook.token}/slack --header 'Content-Type: application/json' --data-binary '{"text": "*ZFS scrub_finish error for test on quartz*
ZFS has detected a data error:\n\n eid: 124\n class: scrub_finish\n host: quartz\n time: \n error: \n objid: :\n pool: test\n"}'
+ msg_out='{"message": "Cannot send an empty message", "code": 50006}'
```
Test method:
`root@quartz:/etc/zfs/zed.d# export ZED_ZEDLET_DIR=/etc/zfs/zed.d; export ZEVENT_EID=124; export ZEVENT_SUBCLASS=scrub_finish; export ZEVENT_POOL=test; export ZED_NOTIFY_DATA=1; bash -x ./data-notify.sh`
Reviewed-by: Damian Szuberski <szuberskidamian@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Philip Kauffman <philip@kauffman.me>
Closes#13049
Raw receiving a snapshot back to the originating dataset is currently
impossible because of user accounting being present in the originating
dataset.
One solution would be resetting user accounting when raw receiving on
the receiving dataset. However, to recalculate it we would have to dirty
all dnodes, which may not be preferable on big datasets.
Instead, we rely on the os_phys flag
OBJSET_FLAG_USERACCOUNTING_COMPLETE to indicate that user accounting is
incomplete when raw receiving. Thus, on the next mount of the receiving
dataset the local mac protecting user accounting is zeroed out.
The flag is then cleared when user accounting of the raw received
snapshot is calculated.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#12981Closes#10523Closes#11221Closes#11294Closes#12594
Issue #11300
When using the two argument version of submit_bio() in kernel's prior
to 4.8 the first argument should be specified. It's used by block
dump to report the bio direction.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Finix Yan <yancw@info2soft.com>
Closes#13006
Linux 5.17 sees a rename from complete_and_exit()
to kthread complete_and_exit()
Upstream commit cead18552660702a4a46f58e65188fe5f36e9dfe
("exit: Rename complete_and_exit to kthread_complete_and_exit")
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12989
Linux decided to rename this for some reason. At some point, we
should probably invert this mapping, but for now...
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Coleman Kane <ckane@colemankane.org>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12975
FreeBSD's implementation of zfs_uio_fault_move() returns EFAULT when a
page fault occurs while copying data in or out of user buffers. The VFS
treats such errors specially and will retry the I/O operation (which may
have made some partial progress).
When the FreeBSD and Linux implementations of zfs_write() were merged,
the handling of errors from dmu_write_uio_dbuf() changed such that
EFAULT is not handled as a partial write. For example, when appending
to a file, the z_size field of the znode is not updated after a partial
write resulting in EFAULT.
Restore the old handling of errors from dmu_write_uio_dbuf() to fix
this. This should have no impact on Linux, which has special handling
for EFAULT already.
Reviewed-by: Andriy Gapon <avg@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#12964
When the eviction thread goes to shrink an ARC state, it allocates a set
of marker buffers used to hold its place in the state's sublists.
This can be problematic in low memory conditions, since
1) the allocation can be substantial, as we allocate NCPU markers;
2) on at least FreeBSD, page reclamation can block in
arc_wait_for_eviction()
In particular, in stress tests it's possible to hit a deadlock on
FreeBSD when the number of free pages is very low, wherein the system is
waiting for the page daemon to reclaim memory, the page daemon is
waiting for the ARC eviction thread to finish, and the ARC eviction
thread is blocked waiting for more memory.
Try to reduce the likelihood of such deadlocks by pre-allocating markers
for the eviction thread at ARC initialization time. When evicting
buffers from an ARC state, check to see if the current thread is the ARC
eviction thread, and use the pre-allocated markers for that purpose
rather than dynamically allocating them.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: George Amanakis <gamanakis@gmail.com>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#12985
There is no need to allocate a holds nvlist. lzc_get_holds does that
for us.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#12967
avl_add does avl_find internally, then avl_insert. We're already doing
the avl_find, so using avl_insert directly avoids repeating the search.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#12967
First open locking changes were correctly applied to zvol_geom_open but
incorrectly applied to zvol_cdev_open, causing spa_namespace_lock to be
held indefinitely.
Make the first open locking in zvol_cdev_open match zvol_geom_open.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#13016
These are the changes for FreeBSD corresponding to the changes made for
Linux in #12863, see that PR for details.
Changes from #12863 are applied for zvol_geom_open and zvol_cdev_open
on FreeBSD. This also adds a check for the zvol dying which we had
in zvol_geom_open but was missing in zvol_cdev_open. The check causes
the open to fail early with ENXIO when we are in the middle of changing
volmode.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#12934
The FreeBSD implementations of various libspl functions for getting
mounted device information were found to leak several strings which
were being allocated in statfs2mnttab but never freed.
The Solaris getmntany(3C) and related interfaces are expected to return
strings residing in static buffers that need to be copied rather than
freed by the caller.
Use static thread-local storage to stash the mnttab structure strings
from FreeBSD's statfs info rather than strings allocated on the heap by
strdup(3).
While here, remove some stray commented out lines.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Rich Ercolani <rincebrain@gmail.com>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#12961
sc.nr_to_scan is an input to super_cache_clean (via
shrinker->scan_objects), used to set the number of objects to scan
in the various caches. However super_cache_scan also modifies
sc.nr_to_scan, so when used in a loop we need to reset
sc.nr_to_scan back to our desired nr_to_scan for the next
iteration.
Issue discovered and solution suggested by
Tenzin Lhakhang @tlhakhan.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chris Dunlop <chris@onthe.net.au>
Issue #12433Closes#12908
Verify that all empty sectors are zero filled before using them to
calculate parity. Failure to do so can result in incorrect parity
columns being generated and written to disk if the contents of an
empty sector are non-zero. This was possible because the checksum
only protects the data portions of the buffer, not the empty sector
padding.
This issue has been addressed by updating raidz_parity_verify() to
check that all dRAID empty sectors are zero filled. Any sectors
which are non-zero will be fixed, repair IO issued, and a checksum
error logged. They can then be safely used to verify the parity.
This specific type of damage is unlikely to occur since it requires
a disk to have silently returned bad data, for an empty sector, while
performing a scrub. However, if a pool were to have been damaged
in this way, scrubbing the pool with this change applied will repair
both the empty sector and parity columns as long as the data checksum
is valid. Checksum errors will be reported in the `zpool status`
output for any repairs which are made.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12857
When performing I/O on FreeBSD using a file based vdev ensure all
errors encountered when reading/writing are propagated through the
zio pipeline.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12904
Any error from lzc_send_redacted is overwritten by the error of
send_conclusion_record; skip writing the conclusion record if there
was an earlier error.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Philipp Riederer <philipp@riederer.email>
Closes#12766
pidfile_open() sets *pidptr to -1 if the process currently holding
the lock is between pidfile_open() and pidfile_write(),
the subsequent kill(mountdpid) would potentially SIGHUP all
non-system processes except init: just sleep for half a millisecond
and try again in that case
Reviewed-by: Don Brady <don.brady@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12067
When restructuring the zvol_open() logic for the Linux 5.13 kernel
a lock inversion was accidentally introduced. In the updated code
the spa_namespace_lock is now taken before the zv_suspend_lock
allowing the following scenario to occur:
down_read <=== waiting for zv_suspend_lock
zvol_open <=== holds spa_namespace_lock
__blkdev_get
blkdev_get_by_dev
blkdev_open
...
mutex_lock <== waiting for spa_namespace_lock
spa_open_common
spa_open
dsl_pool_hold
dmu_objset_hold_flags
dmu_objset_hold
dsl_prop_get
dsl_prop_get_integer
zvol_create_minor
dmu_recv_end
zfs_ioc_recv_impl <=== holds zv_suspend_lock via zvol_suspend()
zfs_ioc_recv
...
This commit resolves the issue by moving the acquisition of the
spa_namespace_lock back to after the zv_suspend_lock which restores
the original ordering.
Additionally, as part of this change the error exit paths were
simplified where possible.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Rich Ercolani <rincebrain@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12863
On FreeBSD vnode reclamation is single-threaded, protected by single
global lock. Linux seems to be able to use a thread per mount point,
but at this time it creates more harm than good.
Reduce number of threads to 1, adding tunable in case somebody wants
to try more.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Chris Dunlop <chris@onthe.net.au>
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#12896
Issue #9966
va_seq was actually a thin veil over va_gen, so z_gen is a more
appropriate value than z_seq to populate the field with.
Drop the unnecessary compat obfuscation and provide the correct
file generation number.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <freqlabs@freebsd.org>
Closes#12851
To ensure that the necessary packages are available during the %post and
%preun scriptlets, require them properly.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Till Maas <opensource@till.name>
Closes#12822Closes#12832
- To avoid a use-after-free, zfsvfs->z_log needs to be loaded after the
teardown lock is acquired with ZFS_ENTER().
- Avoid leaking vnode locks in zfs_rename_relock() and zfs_rename_()
when the ZFS_ENTER() macros forces an early return.
Refactor the rename implementation so that ZFS_ENTER() can be used
safely. As a bonus, this lets us use the ZFS_VERIFY_ZP() macro instead
of open-coding its implementation.
Reported-by: Peter Holm <pho@FreeBSD.org>
Tested-by: Peter Holm <pho@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Sponsored-by: The FreeBSD Foundation
Closes#12717
We have to hold the teardown lock while dereferencing zfsvfs->z_os and,
I believe, when committing to the ZIL.
Note that jumping to the "out" label, "error" is always non-zero.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#12704
The objset object is reallocated during certain dataset operations, such
as rollbacks, so the objset pointer must be loaded after acquiring the
teardown lock.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#12704
The import_rewind_device_replaced.ksh test was never entirely reliable
because it depends on MOS data not being overwritten. The MOS data is
not protected by the snapshot so occasional failures were always
expected. However, this test is now failing reliably on all platforms
indicating something has changed in the code since the test was marked
"maybe". Convert the test to a "known" failure until the root cause
is identified and resolved.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12821
Improve the ability of zfs send to determine if a block is compressed
or not by using information contained in the blkptr.
Reviewed-by: Rich Ercolani <rincebrain@gmail.com>
Reviewed-by: Matthew Ahrens <matthew.ahrens@delphix.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#12770
Newer zstd code introduced in the main kernel tree now creates a symbol
collision with ZSTD_isError in our ZSTD code. This change relabels our
implementation with a ZFS-specific symbol name, and undoes some
macro-based micro-optimizations that conflict with the attempt to rename
our internal-use version.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#12819
The definition of struct blkcg_gq was moved into blk-cgroup.h, which is
a header that's been in Linux since 2015. This is used by
vdev_blkg_tryget() in module/os/linux/zfs/vdev_disk.c. Since the kernel
for CentOS 7 and similar-generation releases doesn't have this header,
its inclusion is guarded by a configure test.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#12819
This change adds a confiugre check to determine if bio_set_dev is a
helper macro or not. If not, then the attempt to override its internal
call to bio_associate_blkg(), with a macro definition to our own
version, is no longer possible, as the compiler won't use it when
compiling the new inline function replacement implemented in the header.
This change also creates a new vdev_bio_set_dev() function that performs
the same work, and also performs the work implemented in
vdev_bio_associate_blkg(), as it is the only thing calling that function
in our code. Our custom vdev_bio_associate_blkg() is now only compiled
if the bio_set_dev() is a macro in the Linux headers.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#12819
The iov_iter->type member was renamed iov_iter->iter_type. However,
while looking into this, realized that in 2018 a iov_iter_type(*iov)
accessor function was introduced. So if that is present, use it,
otherwise fall back to trying the existing behavior of directly
accessing type from iov_iter.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#12819
The return type for the submit_bio member of struct
block_device_operations was changed to no longer return a value.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#12819
Linux 5.16 moved these functions into this new header in commit
1b4fb8545f2b00f2844c4b7619d64d98440a477c. This change adds code to look
for the presence of this header, and include it so that the code using
xgetbv & xsetbv will compile again.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#12800
The upload artifact functionality in github can't handle colons in
filenames. The current code handles this for files under the most
recent set of results. With the ability to rerun failed tests, now
there can be multiple sets of results, and they all need to be
processed in the same way.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: John Kennedy <john.kennedy@delphix.com>
Closes#12815
Due to a possible lock inversion the zvol open call path on Linux
needs to be able to retry in the case where the spa_namespace_lock
cannot be acquired.
For Linux 5.12 an older kernel this was accomplished by returning
-ERESTARTSYS from zvol_open() to request that blkdev_get() drop
the bdev->bd_mutex lock, reaquire it, then call the open callback
again. However, as of the 5.13 kernel this behavior was removed.
Therefore, for 5.12 and older kernels we preserved the existing
retry logic, but for 5.13 and newer kernels we retry internally in
zvol_open(). This should always succeed except in the case where
a pool's vdev are layed on zvols, in which case it may fail. To
handle this case vdev_disk_open() has been updated to retry when
opening a device when -ERESTARTSYS is returned.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #12301Closes#12759
With the addition of functionality to rerun failing tests, some
tests that fail only sometimes still fail often enough to degrade
the reliability of the sanity runs. Remove them from the runfile
until they reliably pass.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: John Kennedy <john.kennedy@delphix.com>
Closes#12814
This was a project proposed as part of the Quality theme for the
hackthon for the 2021 OpenZFS Developer Summit. The idea is to improve
the usability of the automated tests that get run when a PR is created
by having failing tests automatically rerun in order to make flaky
tests less impactful.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#12740
Instead, linux/pagemap.h offers a number of folio-specific functions to
be called instead. In this case, module/os/linux/zfs/zfs_vnops_os.c
wants to call wait_on_page_bit(pp, PG_writeback). This gets replaced
with folio_wait_bit(folio_page(pp), PG_writeback). This change modifies
the code to conditionally compile that if configure identifies th
presence of the folio_wait_bit() function.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#12800
Userland figures out which encryption-root keys are required to load,
and issues ZFS_IOC_LOAD_KEY.
The tail section of spa_keystore_load_wkey() will call
zvol_create_minors() on the encryption-root object.
Any clones of the encrypted zvol will not be plumbed. This commits
adds additional logic to detect if zvol has clones, and is encrypted,
then adds these to the list of zvols to call zvol_create_minors() on.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Closes#12471
In addition to flushing memory mapped regions when checking holes,
commit de198f2d95 modified the dirty dnode detection logic to check
the dn->dn_dirty_records instead of the dn->dn_dirty_link. Relying
on the dirty record has not be reliable, switch back to the previous
method.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #11900Closes#12745
When using lseek(2) to report data/holes memory mapped regions of
the file were ignored. This could result in incorrect results.
To handle this zfs_holey_common() was updated to asynchronously
writeback any dirty mmap(2) regions prior to reporting holes.
Additionally, while not strictly required, the dn_struct_rwlock is
now held over the dirty check to prevent the dnode structure from
changing. This ensures that a clean dnode can't be dirtied before
the data/hole is located. The range lock is now also taken to
ensure the call cannot race with zfs_write().
Furthermore, the code was refactored to provide a dnode_is_dirty()
helper function which checks the dnode for any dirty records to
determine its dirtiness.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Rich Ercolani <rincebrain@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #11900Closes#12724
The ZED code currently can only turn on the fault LED for
a faulted disk in a JBOD enclosure. This extends support
for faulted NVMe disks as well.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#12648Closes#12695
The submit_bio() prototype has changed again. The version is 5.16
still only expects a single argument but the return type has changed
to void. Since we never used the returned value before update the
configure check to detect both single arg versions.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12725
Commit https://github.com/torvalds/linux/commit/2e9bc346 moved
the elevator.h header under the block/ directory as part of some
refactoring. This turns out not to be a problem since there's
no longer anything we need from the header. This has been the
case for some time, this change removes the elevator.h include
and replaces it with a major.h include.
Reviewed-by: Alexander Lobakin <alobakin@pm.me>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12725
One of our developers noticed a bug in vdev_id where we were incorrectly
sorting PHYs using alphabetical sorting (which usually works) instead
of natural sorting (-v). For example:
[port-0:0]# ls -d phy*
phy-0:10 phy-0:11 phy-0:8 phy-0:9
[port-0:0]# ls -vd phy*
phy-0:8 phy-0:9 phy-0:10 phy-0:11
This fixes the issue.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#12699
The vdev_id.conf "enclosure_symlinks" option persistently creates
and maps /dev/by-enclosure symlinks to dynamic /dev/sg* devices.
This patch fixes two issues:
1. The enclosure_symlinks feature was accidentally broken in:
vdev_id: Support daisy-chained JBODs in multipath mode
2. Even when working, the feature numbered the enclosure
sequentially rather than by HBA port number. That meant that
if a port was down or didn't appear in sysfs, then the
enclosure_sumlinks numbers would be numbered wrong.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Arshad Hussain <arshad.hussain@aeoncomputing.com>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#12660
When you create a pool, zfs writes vd->vdev_enc_sysfs_path with the
enclosure sysfs path to the fault LEDs, like:
vdev_enc_sysfs_path = /sys/class/enclosure/0:0:1:0/SLOT8
However, this enclosure path doesn't get updated on successive imports
even if enclosure path to the disk changes. This patch fixes the issue.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#11950Closes#12095
prng32_bounded() is available to kernel only on FreeBSD 13+.
Call inline random_get_pseudo_bytes() with correct pointer type.
To be consistent, apply to Linux as well.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Martin Matuska <mm@FreeBSD.org>
Closes#12282
When cleaning up a test case standardize on using the convention:
datasetexists $ds && destroy_dataset $ds <flags>
By using 'destroy_dataset' instead of 'log_must zfs destroy' we ensure
that the destroy is retried in the event that a ZFS volume is busy.
This helps ensures ensure tests are fully cleaned up and prevents false
positive test failures on Linux.
Note that all of the tests which used 'zfs destroy' in cleanup have
been updated even if they don't use volumes. This was done to
clearly establish the expected convention.
Reviewed-by: Rich Ercolani <rincebrain@gmail.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12663
cloud-init added a hook which triggers on every device add/rm
event, which results in holding open devices for a while after
they're created/destroyed.
So let's shove an exclusion rule for that into the GH workflows
until it gets fixed.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12644Closes#12669
As of the Linux 5.9 kernel a fallthrough macro has been added which
should be used to anotate all intentional fallthrough paths. Once
all of the kernel code paths have been updated to use fallthrough
the -Wimplicit-fallthrough option will because the default. To
avoid warnings in the OpenZFS code base when this happens apply
the fallthrough macro.
Additional reading: https://lwn.net/Articles/794944/
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12441
It turns out the ax_python_devel.m4 version check assumes that
("3.X+1.0" >= "3.X.0") is True in Python, which is not when X+1
is 10 or above and X is not. (Also presumably X+1=100 and ...)
So let's remake the check to behave consistently, using the
"packaging" or (if absent) the "distlib" modules.
(Also, update the Github workflows to use the new packages.)
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes: #12073
Increase the Linux-Maximum version in the META file to 5.14.
All of the required compatibility patches have been merged
and the 5.14 kernel has been officially released.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12565
Errors in zil_lwb_write_done() are not propagated to
zil_lwb_flush_vdevs_done() which can result in zil_commit_impl()
not returning an error to applications even when zfs was not able
to write data to the disk.
Remove the ZIO_FLAG_DONT_PROPAGATE flag from zio_rewrite() to
allow errors to propagate and consolidate the error handling for
flush and write errors to a single location (rather than having
error handling split between the "write done" and "flush done"
handlers).
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Prakash Surya <prakash.surya@delphix.com>
Signed-off-by: Arun KV <arun.kv@datacore.com>
Closes#12391Closes#12443
This is a follow up patch for PR #12515 which addresses some
additional ZTS tests which are unreliable are should explicitly
wait for the required zvols to be available.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: @Theo13111
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12553
The block pointer verification check in arc_read() should also
cover embedded block pointers. While highly unlikely, accessing
a damaged block pointer can result in panic. To further harden
the code extend the existing check to include embedded block
pointers and add a comment explaining the rational for this
sanity check. Lastly, correct a flaw in zfs_blkptr_verify()
so the error count is checked even when checking a untrusted
config to verify the non-pool-specific portions of a block
pointer.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12535
Kernel commits
332f606b32b6 ovl: enable RCU'd ->get_acl()
0cad6246621b vfs: add rcu argument to ->get_acl() callback
Added compatibility code to detect the new ->get_acl() interface
and correctly handle the case where the new rcu argument is set.
Reviewed-by: Coleman Kane <ckane@colemankane.org>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12548
When zfs_send_corrupt_data is set, use the TRAVERSE_HARD flag,
so traverse_visitbp() will not fail with ECKSUM if a blockpointer
cannot be read, but rather will continue and send the objects it can.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Sponsored-By: Klara Inc.
Sponsored-By: WHC Online Solutions Inc.
Closes#12541
Unfortunately, there was an overzealous assertion that was (in pretty
specific circumstances) false, causing failure. This assertion was
added in error, so we're removing it.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#9897Closes#12020Closes#12246
We round up the psize to the nearest multiple of the asize or to the
lsize, whichever is smaller. Once that's done, we allocate a new
buffer of the appropriate size, zero the tail, and copy the data
into it. This adds a small performance cost to these kinds of writes,
but fixes the bookkeeping problems.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Co-authored-by: Matthew Ahrens <matthew.ahrens@delphix.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#12522Closes#8462
Kernel commits
39f75da7bcc8 ("isystem: trim/fixup stdarg.h and other headers")
c0891ac15f04 ("isystem: ship and use stdarg.h")
564f963eabd1 ("isystem: delete global -isystem compile option")
(for now can be found in linux-next.git tree, will land into the
Linus' tree during the ongoing 5.15 cycle with one of akpm merges)
removed the -isystem flag and disallowed the inclusion of any
compiler header files. They also introduced a minimal
<linux/stdarg.h> as a replacement for <stdarg.h>.
include/os/linux/spl/sys/cmn_err.h in the ZFS source tree includes
<stdarg.h> unconditionally. Introduce a test for <linux/stdarg.h>
and include it instead of the compiler's one to prevent module
build breakage.
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Closes#12531
The 5.15 kernel moved the backing_dev_info structure out of
the request queue structure which causes a build failure.
Rather than look in the new location for the BDI we instead
detect this upstream refactoring by the existance of either
the blk_queue_update_readahead() or disk_update_readahead()
functions. In either case, there's no longer any reason to
manually set the ra_pages value since it will be overridden
with a reasonable default (2x the block size) when
blk_queue_io_opt() is called.
Therefore, we update the compatibility wrapper to do nothing
for 5.9 and newer kernels. While it's tempting to do the
same for older kernels we want to keep the compatibility
code to preserve the existing behavior. Removing it would
effectively increase the default readahead to 128k.
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12532
We attempt to remove an existing SA xattr when setting a dir xattr, but
this only makes sense if the znode has been upgraded to the SA format.
Otherwise, we will hit an assert in zfs_sa_get_xattr.
Make sure this is an SA znode before attempting to remove the SA xattr.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#12514
It turns out that layouts of union bitfields are a pain, and the
current code results in an inconsistent layout between BE and LE
systems, leading to zstd-active datasets on one erroring out on
the other.
Switch everyone over to the LE layout, and add compatibility code
to read both.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12008Closes#12022
The ZTS block_device_wait helper function should use -e when waiting
for a file to appear since it will be either a block special device
or a symlink. This didn't cause any failures but when a device path
was specified the function would wait longer than needed.
Additionally update the most flakey test cases to pass the file path
to block_device_wait to try and improve the test reliability. The
udev behavior on Fedora in particular can result in frequent false
positives.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12515
This patch allows you to clear the label on offlined disks in an active
pool with `-f`. Previously, labelclear wouldn't let you do that.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#12511
Document that top-level vdevs cannot be removed unless all top-level
vdevs have the same sector size.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Sam Hathaway <sam@sam-hathaway.com>
Closes#11339Closes#12472
benchmark_raidz() allocates a row to benchmark parity calculation and
reconstruction. In the latter case, the parity blocks are left
uninitialized, leading to reports from KMSAN.
Initialize parity blocks to 0xAA as we do for the data earlier in the
function. This does not affect the selected RAID-Z implementation on
any of several systems tested.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#12473
Linux 4.11 added a new statx system call that allows us to expose crtime
as btime. We do this by caching crtime in the znode to match how atime,
ctime and mtime are cached in the inode.
statx also introduced a new way of reporting whether the immutable,
append and nodump bits have been set. It adds support for reporting
compression and encryption, but the semantics on other filesystems is
not just to report compression/encryption, but to allow it to be turned
on/off at the file level. We do not support that.
We could implement semantics where we refuse to allow user modification
of the bit, but we would need to do a dnode_hold() in zfs_znode_alloc()
to find out encryption/compression information. That would introduce
locking that will have a minor (although unmeasured) performance cost.
It also would be inferior to zdb, which reports far more detailed
information. We therefore omit reporting of encryption/compression
through statx in favor of recommending that users interested in such
information use zdb.
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Richard Yao <ryao@gentoo.org>
Closes#8507
When a header is allocated for full overwrite it is a waste of time
to allocate b_pabd/b_rabd for it, since arc_write() will free them
without ever being touched. If it is a read or a partial overwrite
then arc_read() and arc_hdr_decrypt() allocate them explicitly.
Reduced memory allocation in user threads also reduces ARC eviction
throttling there, proportionally increasing it in ZIO threads, that
is not good. To minimize or even avoid it introduce ARC allocation
reserve, allowing certain arc_get_data_abd() callers to allocate a
bit longer in situations where user threads will already throttle.
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#12398
It is very expensive and not informative to call multilist_is_empty()
for each arc_change_state() on debug builds to check for impossible.
Instead implement special index function for arc_l2c_only->arcs_list,
multilists, panicking on any attempt to use it.
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#12421
Instead of clearing stats inside arc_buf_alloc_impl() do it inside
arc_hdr_alloc() and arc_release(). It fixes statistics being wiped
every time a new dbuf is filled from the ARC.
Remove b_l1hdr.b_l2_hits. L2ARC hits are accounted at b_l2hdr.b_hits.
Since the hits are accounted under hash lock, replace atomics with
simple increments.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Wilson <george.wilson@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#12422
vq_lock is already too congested for two more operations per I/O.
Instead of dropping and reacquiring it inside vdev_queue_aggregate()
delegate the zio_vdev_io_bypass() and zio_execute() calls for parent
I/Os to callers, that drop the lock any way to execute the new I/O.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#12297
Use atomic_load_64() for zfs_refcount_count() to prevent torn reads
on 32-bit platforms. On 64-bit ones it should not change anything.
When built with ZFS_DEBUG but running without tracking enabled use
atomics instead of mutexes same as for builds without ZFS_DEBUG.
Since rc_tracked can't change live we can check it without lock.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#12420
The redacted_send tests make use of a $tmpdir variable, except in
redacted_send/redacted_panic the variable is never defined.
Use $TEST_BASE_DIR instead.
Clean up the stream file after the test.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#12455
Before OpenZFS 2.0, trying to set the FreeBSD sysctl vfs.zfs.arc_max
to a disallowed value would return an error.
Since the switch, it instead only generates WARN_IF_TUNING_IGNORED
Keep the ability to set the sysctl's specifically to 0, even though
that is less than the minimum, because some tests depend on this.
Also lost, was the ability to set vfs.zfs.arc_max to a value less
than the default vfs.zfs.arc_min at boot time. Restore this as well.
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Closes#12161
zfs.sh already can load and unload, so why not both?
This is convenient when developing changes to the module and you want
to rapidly make some changes, rebuild the module, reload the module,
and test the changes.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#12450
Run arc_evict thread at higher priority, nice=0, to give it more CPU
time which can improve performance for workload with high ARC evict
activities.
On mixed read/write and sequential read workloads, I've seen between
10-40% better performance.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Tony Nguyen <tony.nguyen@delphix.com>
Closes#12397
It turns out, there are a lot of possible reasons for fopen to fail.
Let's share which reason we failed for today.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12410
The /proc/diskstats accounting needs to be explicitly enabled
for block devices which do not use multi-queue.
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12440Closes#12066
CpaDcGeneratefooter function that obtain the checksum code
does not support the CPA_DC_STATELESS mode. So we get the
adler32 chencksum of the end of the zlib from dc_results.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Chengfei Zhu <chengfeix.zhu@intel.com>
Signed-off-by: hedong.zhang <h_d_zhang@163.com>
Closes#12343
We have a tunable which permits one to disable the use of unmapped I/O
for the buffer cache. Respect it in ZFS as well. This is useful for
KMSAN, which cannot easily maintain shadow state for unmapped pages.
No functional change intended, as unmapped I/O is permitted by default
and there's no real reason to disable it in practice except for
debugging.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#12446
- Bail out early if we're running the perf tests and forget to
specify disks.
- Allow perf tests to run with any number of disks.
- Remove weekly vs. nightly settings
- Move variables with common values to perf.shlib
- Use zinject to clear the ARC over export/import
- Fix dbuf cache size calculation
When the meaning of `dbuf_cache_max_bytes` changed, the performance
test that covers the dbuf cache started to fail. The test would try to
write files for the test using the max possible size of the cache,
inevitably filling the pool and failing. This change uses
`dbuf_cache_shift` to correctly calculate the dbuf cache size.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: John Kennedy <john.kennedy@delphix.com>
Closes#12408
`zpool_do_import()` passes `argv[0]`, (optionally) `argv[1]`, and
`pool_specified` to `import_pools()`. If `pool_specified==FALSE`, the
`argv[]` arguments are not used. However, these values may be off the
end of the `argv[]` array, so loading them could dereference unmapped
memory. This error is reported by the asan build:
```
=================================================================
==6003==ERROR: AddressSanitizer: heap-buffer-overflow
READ of size 8 at 0x6030000004a8 thread T0
#0 0x562a078b50eb in zpool_do_import zpool_main.c:3796
#1 0x562a078858c5 in main zpool_main.c:10709
#2 0x7f5115231bf6 in __libc_start_main
#3 0x562a07885eb9 in _start
0x6030000004a8 is located 0 bytes to the right of 24-byte region
allocated by thread T0 here:
#0 0x7f5116ac6b40 in __interceptor_malloc
#1 0x562a07885770 in main zpool_main.c:10699
#2 0x7f5115231bf6 in __libc_start_main
```
This commit passes NULL for these arguments if they are off the end
of the `argv[]` array.
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#12339
In l2arc_add_vdev() first decide whether the device is eligible for
L2ARC rebuild or whole device trim and then add it to the list of cache
devices. Otherwise l2arc_feed_thread() might already start writing on
the device invalidating previous content as l2ad_hand = l2ad_start.
However l2arc_rebuild_vdev() needs the device present in the cache
device list to figure out its l2arc_dev_t. Fix this by moving most of
l2arc_rebuild_vdev() in a new function l2arc_rebuild_dev() which does
not need to search in the cache device list.
In contrast to l2arc_add_vdev() we do not have to worry about
l2arc_feed_thread() invalidating previous content when onlining a
cache device. The device parameters (l2ad*) are not cleared when
offlining the device and writing new buffers will not invalidate
all previous content. In worst case only buffers that have not had
their log block written to the device will be lost.
Retire persist_l2arc_00{4,5,8} tests since they cover code already
covered by the remaining ones. Test persist_l2arc_006 is renamed to
persist_l2arc_004 and persist_l2arc_007 is renamed to persist_l2arc_005.
Fix a typo in persist_l2arc_004, and remove an assertion that is not
always true from l2arc_arcstats_pos. Also update an assertion in
persist_l2arc_005 and explain why in a comment.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#12365
It seems nothing ensures that this array is zeroed when a dnode is
freshly allocated, so in principle it retains the values from the
previous allocation. In practice it seems to be the case that the
fields should end up zeroed, but we can zero the field anyway for
consistency.
This was found using KMSAN.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#12383
When logging a TX_WRITE record in the case where file data has to be
copied from the DMU, we pad the log record size to a multiple of 8
bytes. In this case, any padding bytes should be zeroed, otherwise the
contents of uninitialized memory are written to the ZIL.
This was found using KMSAN.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#12383
When allocating a record, we round up the allocation size to a multiple
of 8. In this case, any padding bytes should be zeroed, otherwise the
contents of uninitialized memory are written to the ZIL.
This was found using KMSAN.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#12383
When logging TX_SETATTR, we could otherwise fail to initialize part of
the corresponding ZIL record depending on which fields are present in
the xvattr. Initialize the creation time and the AV scan timestamp to
zero so that uninitialized bytes are not written to the ZIL.
This was found using KMSAN.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#12383
spa_prop_find() may fail to find the specified property, in which case
it suppresses ENOENT from zap_lookup(). In this case, the return value
is left uninitialized, so spa_autoreplace was being initialized using an
uninitialized stack variable.
This was found using KMSAN. It appears to be a regression from commit
9eb7b46ed0, which removed the initialization of "autoreplace" from the
definition.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#12383
Kernel 5.14 introduced a change where set_page_dirty of
struct address_space_operations is no longer implicitly set to
__set_page_dirty_buffers(), which ended up resulting in a NULL
pointer deref in the kernel when it is attempted to be called.
This change sets .set_page_dirty in the structure to
__set_page_dirty_nobuffers(), which was introduced with the
related patch set. The breaking change was introduce in commit
0af573780b0b13fceb7fabd49dc1b073cee9a507 to torvalds/linux.git.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#12427
After 1325434b, we can in certain circumstances end up calling
spa_update_dspace with vd->vdev_mg NULL, which ends poorly during
vdev removal.
So let's not do that further space adjustment when we can't.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12380Closes#12428
In Linux 5.14, blk_alloc_queue is no longer exported, and its usage
has been superseded by blk_alloc_disk, which returns a gendisk struct
from which we can still retrieve the struct request_queue* that is
needed in the one place where it is used. This also replaces the call
to alloc_disk(minors), and minors is now set via struct member
assignment.
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Reviewed-by: Coleman Kane <ckane@colemankane.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12362Closes#12409
It is useful to have control over the number of iterations of zloop so
we can easily produce "x core dumps found *in y iterations*" metrics.
Using random values for run/pass times doesn't improve coverage in a
meaningful way.
Randomizing run time could be seen as a compromise between running a
greater variety of shorter tests versus a smaller variety of longer
tests within a fixed time span. However, it is not desirable when
running a fixed number of iterations.
Pass time already incorporates randomness within ztest.
Either parameter can be passed to ztest explicitly if the defaults are
not satisfactory.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#12411
Since errors returned by zvol_create_minor_impl() are ignored by the
common code, it is more convenient to ignore make_dev_s() errors there.
It allows, for example, to get device created for the zvol after later
rename instead of having it further stuck in half-created state.
zvol_rename_minor() already ignores those errors.
While there, switch from MAXPHYS to maxphys in FreeBSD 13+.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#12375
Possibly required in the past, but is currently fills no purpose.
Ordinarily such tiny cleanup is not generally worth it, however
on the macOS port, in a future commit, we do unspeakable things to the
"fd" for send/recv, and it would be easier to only have to deal with
one "fd" instead of two.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Closes#12404
Remove mc_lock use from metaslab_class_throttle_*(). The math there
is based on refcounts and so atomic, so the only race possible there
is between zfs_refcount_count() and zfs_refcount_add(). But in most
cases metaslab_class_throttle_reserve() is called with the allocator
lock held, which covers the race. In cases where the lock is not
held, GANG_ALLOCATION() or METASLAB_MUST_RESERVE are set, and so we
do not use zfs_refcount_count(). And even if we assume some other
non-existing scenario, the worst that may happen from this race is
few more I/Os get to allocation earlier, that is not a problem.
Move locks and data of different allocators into different cache
lines to avoid false sharing. Group spa_alloc_* arrays together
into single array of aligned struct spa_alloc spa_allocs. Align
struct metaslab_class_allocator.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Don Brady <don.brady@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#12314
Remove unneeded global, practically constant, state pointer variables
(arc_anon, arc_mru, etc.), replacing them with macros of real state
variables addresses (&ARC_anon, &ARC_mru, etc.).
Change ARC_EVICT_ALL from -1ULL to UINT64_MAX, not requiring special
handling in inner loop of ARC reclamation. Respectively change bytes
argument of arc_evict_state() from int64_t to uint64_t.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#12348
Ensure all calls to bqueue_init() has a corresponding call to bqueue_destroy()
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Co-authored-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Closes#12118
* zio: avoid callback typecasting
* zil: avoid zil_itxg_clean() callback typecasting
* zpl: decouple zpl_readpage() into two separate callbacks
* nvpair: explicitly declare callbacks for xdr_array()
* linux/zfs_nvops: don't use external iput() as a callback
* zcp_synctask: don't use fnvlist_free() as a callback
* zvol: don't use ops->zv_free() as a callback for taskq_dispatch()
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Closes#12260
zfs-send(8) claimed in the flags list you could use -pR when sending
a readonly filesystem or volume. You cannot.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12336
Most of dsl_dir_diduse_space() and dsl_dir_transfer_space() CPU time
is a dd_lock overhead and time spent in dmu_buf_will_dirty(). Calling
them one after another is a waste of time and even more contention.
Doing that twice for each rewritten block within dbuf_write_done()
via dsl_dataset_block_kill() and dsl_dataset_block_born() created one
of the biggest CPU overheads in case of small blocks rewrite.
dsl_dir_diduse_transfer_space() combines functionality of these two
functions for cases where it is needed, but without double overhead,
practically for the cost of dsl_dir_diduse_space() or even cheaper.
While there, optimize dsl_dir_phys() calls in dsl_dir_diduse_space()
and dsl_dir_transfer_space(). It seems Clang detects some aliasing
there, repeating dd->dd_dbuf->db_data dereference multiple times,
increasing dd_lock scope and contention.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Author: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#12300
In absence of LTO, and dynamic libatomic, la.so ends up in the needs
section of every toolchain executable; some consider this an issue.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12345Closes#12359
* Tinker with slop space accounting with dedup
Do not include the deduplicated space usage in the slop space
reservation, it leads to surprising outcomes.
* Update spa_dedup_dspace sometimes
Sometimes, we get into spa_get_slop_space() with
spa_dedup_dspace=~0ULL, AKA "unset", while spa_dspace is correctly set.
So call the code to update it before we use it if we hit that case.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12271
arc_evict_hdr() returns number of evicted bytes in scope of specific
state. For ghost states it does not mean the amount of really freed
memory, but the logical buffer size. It is correct for the eviction
process, but not for waking up threads waiting for ARC size reduction,
as added in "Revise ARC shrinker algorithm" commit, causing premature
wakeups while ARC is still overflowed, allowing even bigger overflow,
plus processing overhead when next allocation will also get blocked,
probably also for too short time.
To fix that make arc_evict_hdr() also return the amount of really
freed memory, which for the ghost states is only the header, and use
it to update arc_evict_count instead. Originally I was thinking to
not return it at all, since arc_get_data_impl() does not account for
the headers, but decided that some slow allocation progress is better
than long waits, reaching on my tests up to 100ms.
To reduce negative latency effects of long time periods when reclaim
thread can free little real memory, start reclamation process earlier,
before we actually reached the overflow threshold, when we have to
throttle new allocations. We can also do it without taking global
arc_evict_lock, reducing the contention.
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#12279
- Remove the "SPL Version" line, the repositories have been merged
since the 0.8 release and we no longer need to ask about this.
- Simply ask for the kernel version / patch level and add a hint
about how to get this information on Linux and FreeBSD.
- Remove "Status: Triage Needed" from the template, in practice
we really haven't been using this label so let's step setting it.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes: #12340
Callers of zfs_file_get and zfs_file_put can corrupt the reference
counts for the file structure resulting in a panic or a soft lockup.
When zfs send/recv runs, it will add a reference count to the
open file, and begin to send or recv the stream. If the file descriptor
is closed, then when dmu_recv_stream() or dmu_send() return we will
call zfs_file_put to remove the reference we placed on the file
structure. Unfortunately, because zfs_file_put() uses the file
descriptor to lookup the file structure, it may end up finding that
the file descriptor table no longer contains the file struct, thus
leaking the file structure. Or it might end up finding a file
descriptor for a different file and blindly updating its reference
counts. Other failure modes probably exists.
This change reworks the zfs_file_[get|put] interface to not rely
on the file descriptor but instead pass the zfs_file_t pointer around.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Co-authored-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: George Wilson <gwilson@delphix.com>
External-issue: DLPX-76119
Closes#12299
Could have gone either way with this one, either adding it to
macOS/Windows SPL, or returning it to "classic" usage with strrchr().
Since the new special way isn't really used, and only used once,
we have this commit.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Closes #12312
Many FreeBSD disk drivers support "unmapped" I/O mode, when data
buffer represented not with a virtually contiguous KVA-mapped address
range, but with a list of physical memory pages. Originally it was
designed to do I/O from buffers without KVA mapping (unmapped). But
moving virtual addresses out of equation allows us to operate even
non-contiguous data buffers with one condition: all buffer discon-
tinuities must be aligned to memory page borders.
Doing I/O to capable GEOM device this patch traverses through non-
linear ABD buffers, validating the chunks borders. If the condition
is met, it supplies GEOM with the list of original physical memory
pages instead of copying the data into temporary contiguous buffer.
On capable hardware on pools with ashift=12 and default ABD chunk of
4KB it should handle all the I/O without additional memory copying.
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#12320
It makes no sense to set it below PAGE_SIZE, since it increases all
overheads and makes returning memory to OS problematic. It makes no
sense to set it above PAGE_SIZE, since such allocations and especially
frees are too expensive and cause KVA fragmentation to benefit from
fewer chunks. After that it makes no sense to keep more complicated
math here.
What may have sense though is just a tunable border between linear and
scatter ABDs, previously also controlled by this tunable. Retain that
functionality by taking abd_scatter_min_size tunable from Linux, just
with different default value.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#12328
This dramatically reduces the lock contention on systems with slower
(non-TSC) timecounters. With TSC the difference is minimal, but since
this lock is pretty congested, any improvement counts. Plus I don't
see any reason to do it under the lock other than the latency of the
lock itself, which this change actually reduces.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#12281
Currently, there are several places in zvol_id where the program logic
returns particular errno values, or even particular ioctl return values,
as the program exit status, rather than a straightforward system of
explicit zero on success and explicit nonzero value(s) on failure.
This is problematic for multiple reasons. One particularly interesting
problem that can arise, is that if any of these values happens to have
all 8 least significant bits unset (i.e., it is a positive or negative
multiple of 256), then although the C program sees a nonzero int value
(presumed to be a failure exit status), the actual exit status as seen
by the system is only the bottom 8 bits of that integer: zero.
This can happen in practice, and I have encountered it myself. In a
particularly weird situation, the zvol_open code in the zfs kernel
module was behaving in such a manner that it caused the open() syscall
to fail and for errno to be set to a kernel-private value (ERESTARTSYS,
which happens to be defined as 512). It turns out that 512 is evenly
divisible by 256; or, in other words, its least significant 8 bits are
all-zero. So even though zvol_id believed it was returning a nonzero
(failure) exit status of 512, the system modulo'd that value by 256,
resulting in the actual exit status visible by other programs being 0!
This actually-zero (non-failure) exit status caused problems: udev
believed that the program was operating successfully, when in fact it
was attempting to indicate failure via a nonzero exit status integer.
Combined with another problem, this led to the creation of nonsense
symlinks for zvol dev nodes by udev.
Let's get rid of all this problematic logic, and simply return
EXIT_SUCCESS (0) is everything went fine, and EXIT_FAILURE (1) if
anything went wrong.
Additionally, let's clarify some of the variable names (error is similar
to errno, etc) and clean up the overall program flow a bit.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Signed-off-by: Justin Gottula <justin@jgottula.com>
Closes#12302
The zvol_id program is invoked by udev, via a PROGRAM key in the
60-zvol.rules.in rule file, to determine the "pretty" /dev/zvol/*
symlink paths paths that should be generated for each opaquely named
/dev/zd* dev node.
The udev rule uses the PROGRAM key, followed by a SYMLINK+= assignment
containing the %c substitution, to collect the program's stdout and then
"paste" it directly into the name of the symlink(s) to be created.
Unfortunately, as currently written, zvol_id outputs both its intended
output (a single string representing the symlink path that should be
created to refer to the name of the dataset whose /dev/zd* path is
given) AND its error messages (if any) to stdout.
When processing PROGRAM keys (and others, such as IMPORT{program}), udev
uses only the data written to stdout for functional purposes. Any data
written to stderr is used solely for the purposes of logging (if udev's
log_level is set to debug).
The unintended consequence of this is as follows: if zvol_id encounters
an error condition; and then udev fails to halt processing of the
current rule (either because zvol_id didn't return a nonzero exit
status, or because the PROGRAM key in the rule wasn't written properly
to result in a "non-match" condition that would stop the current rule on
a nonzero exit); then udev will create a space-delimited list of symlink
names derived directly from the words of the error message string!
I've observed this exact behavior on my own system, in a situation where
the open() syscall on /dev/zd* dev nodes was failing sporadically (for
reasons that aren't especially relevant here). Because the open() call
failed, zvol_id printed "Unable to open device file: /dev/zd736\n" to
stdout and then exited.
The udev rule finished with SYMLINK+="zvol/%c %c". Assuming a volume
name like pool/foo/bar, this would ordinarily expand to
SYMLINK+="zvol/pool/foo/bar pool/foo/bar"
and would cause symlinks to be created like this:
/dev/zvol/pool/foo/bar -> /dev/zd736
/dev/pool/foo/bar -> /dev/zd736
But because of the combination of error messages being printed to
stdout, and the udev syntax freely accepting a space-delimited sequence
of names in this context, the error message string
"Unable to open device file: /dev/zd736\n"
in reality expanded to
SYMLINK+="zvol/Unable to open device file: /dev/zd736"
which caused the following symlinks to actually be created:
/dev/zvol/Unable -> /dev/zd736
/dev/to -> /dev/zd736
/dev/open -> /dev/zd736
/dev/device -> /dev/zd736
/dev/file: -> /dev/zd736
/dev//dev/zd736 -> /dev/zd736
(And, because multiple zvols had open() syscall errors, multiple zvols
attempted to claim several of those symlink names, resulting in numerous
udev errors and timeouts and general chaos.)
This commit rectifies all this silliness by simply printing error
messages to stderr, as Dennis Ritchie originally intended.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Signed-off-by: Justin Gottula <justin@jgottula.com>
Closes#12302
Assignment syntax (=) can be used for the PROGRAM key. But the PROGRAM
key is really a match key, not an assign key. The internal logic used by
udev to decide whether a PROGRAM key "matched" or not (which determines
whether the remainder of the rule is evaluated) depends on whether the
operator was OP_MATCH (==) or OP_NOMATCH (!=). [1]
The man page claims that '"=", ":=", and "+=" have the same effect as
"=="' for PROGRAM keys. And, after a brief perusal, the udev source code
does seem to confirm that operators other than OP_MATCH (==) or
OP_NOMATCH (!=) are implicitly converted to OP_MATCH (==). [2] But it's
not entirely clear that this is definitely the case: anecdotal testing
seems to indicate that when OP_ASSIGN (=) is used, the program's exit
status is disregarded and the remainder of the rule is processed
regardless of whether it was, in fact, a successful exit.
The bottom line here is that, if zvol_id hits some snag and returns a
nonzero exit status, then we almost certainly do NOT want to continue on
with the rule and use whatever the stdout contents may have been to
mindlessly create /dev/zvol/* symlinks. Therefore, let's be extra-sure
and use the match (==) operator explicitly, to eliminate any possibility
that udev might do the wrong thing, and ensure that a nonzero exit
status will definitely short-circuit the rest of the rule, bypassing the
SYMLINK+= assignments.
[1]
udev,
file src/udev/udev-rules.c,
func udev_rule_apply_token_to_event,
switch case TK_M_PROGRAM if r != 0 (nonzero exit status):
return token->op == OP_NOMATCH;
switch case TK_M_PROGRAM if r == 0 (zero exit status):
return token->op == OP_MATCH;
func retval 0 => key is considered to have matched
func retval 1 => key is considered to have NOT matched
[2]
udev,
file src/udev/udev-rules.c,
func parse_token,
at func start:
bool is_match = IN_SET(op, OP_MATCH, OP_NOMATCH);
in else-if case streq(key, "PROGRAM"):
if (!is_match) op = OP_MATCH;
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Signed-off-by: Justin Gottula <justin@jgottula.com>
Closes#12302
The $tempnode substitution is so old that it's not even mentioned in the
man page anymore. It is still technically supported by udev, but with
plenty of "deprecated" comments surrounding it.
The preferred modern equivalent of $tempnode is $devnode (or
alternatively, %N).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Signed-off-by: Justin Gottula <justin@jgottula.com>
Closes#12302
This file is old as dirt. It's entirely possible that commas were
optional in udev back at that time. But they're definitely supposed to
be there nowadays.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Signed-off-by: Justin Gottula <justin@jgottula.com>
Closes#12302
With default dbuf cache size of 1/32 of ARC, it makes no sense to have
hash table of the same size (or even bigger on Linux). Reduce it to
1/8 of ARC's one, still leaving some slack, assuming higher I/O rate
via dbuf cache than via ARC.
Remove padding from ARC hash locks array. The idea behind padding
is to avoid false sharing between locks. It would have sense if
there would be a limited number of very busy locks. But since we
have no limit on the number, using the same memory for more locks we
can achieve even lower lock contention with the same false sharing,
or we can use less memory for the same contention level.
Reduce number of hash locks from 8192 to 2048. The number is still
big enough to not cause contention, but reduced memory size improves
cache hit rate for mutex_tryenter() in ARC eviction thread, saving
about 1% of the thread time.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#12289
Fix a leak of abd_t that manifested mostly when using
raidzN with at least as many columns as N (e.g. a
four-disk raidz2 but not a three-disk raidz2).
Sufficiently heavy raidz use would eventually run a system
out of memory.
Additionally:
* Switch abd_cache arena to FIRSTFIT, which empirically
improves perofrmance.
* Make abd_chunk_cache more performant and debuggable.
* Allocate the abd_zero_buf from abd_chunk_cache rather
than the heap.
* Don't try to reap non-existent qcaches in abd_cache arena.
* KM_PUSHPAGE->KM_SLEEP when allocating chunks from their
own arena
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Co-authored-by: Sean Doran <smd@use.net>
Closes#12295
dmu_zfetch_stream_fini() is missing calls to destroy the refcounts,
leaking them and the mutex inside.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Closes#12294
In all places except two spa_get_random() is used for small values,
and the consumers do not require well seeded high quality values.
Switch those two exceptions directly to random_get_pseudo_bytes()
and optimize spa_get_random(), renaming it to random_in_range(),
since it is not related to SPA or ZFS in general.
On FreeBSD directly map random_in_range() to new prng32_bounded() KPI
added in FreeBSD 13. On Linux and in user-space just reduce the type
used to uint32_t to avoid more expensive 64bit division.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12183
FreeBSD historically has not cared about the xattr property; it was
always treated as xattr=on. With xattr=on, xattrs are stored as files
in a hidden xattr directory. With xattr=sa, xattrs are stored as
system attributes and get cached in nvlists during xattr operations.
This makes SA xattrs simpler and more efficient to manipulate. FreeBSD
needs to implement the SA xattr operations for feature parity with
Linux and to ensure that SA xattrs are accessible when migrated or
replicated from Linux.
Following the example set by Linux, refactor our existing extattr vnops
to split off the parts handling dir style xattrs, and add the
corresponding SA handling parts.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11997
Convert use of ASSERT() to ASSERT0(), ASSERT3U(), ASSERT3S(),
ASSERT3P(), and likewise for VERIFY(). In some cases it ended up
making more sense to change the code, such as VERIFY on nvlist
operations that I have converted to use fnvlist instead. In one
place I changed an internal struct member from int to boolean_t to
match its use. Some asserts that combined multiple checks with &&
in a single assert have been split to separate asserts, to make it
apparent which check fails.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11971
Increase the Linux-Maximum version in the META file to 5.13.
All of the required compatibility patches have been merged
and the 5.13 kernel has been officially released.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
The number of sublists in a multilist is relatively small. We dont need
64 bits to calculate an index. 32 bits is sufficient and makes the
code more efficient.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12288
plymouth --command splits the command on spaces which means
that zfs-load-key was getting the filesystem name enclosed
in single quotes (since 13c59bb76) and failing. This commit
fixes it by piping the password directly to the command
similar to how it's done in other scripts (initramfs,
dracut without plymouth).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Michal Vasilek <michal@vasilek.cz>
Related-to: #9193
Related-to: #9202Closes#12147
The stock zstd code expects some helpers from ASAN if present.
This works fine in userland, but in kernel, KASAN also gets detected,
and lacks those helpers. So let's make some empty substitutes for
that case.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12232
While abd_verify() does nothing when built without debug, compiler
can't optimize it out by itself due to calls to external list_*()
and abd_verify_scatter(). This commit makes it explicit.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Adam Moss <c@yotes.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12280
Unlike most other properties the 'compatibility' property is stored
in the pool config object and not the DMU_OT_POOL_PROPS object.
This had the advantage that the compatibility information is available
without needing to fully import the pool (it can be read with zdb).
However, this means we need to make sure to update both the copy of
the config in the MOS and the cache file. This wasn't being done.
This commit adds a call to spa_async_request() to ensure the copy of
the config in the cache file gets updated as well as the one stored
in the pool. This same change is made for the 'comment' property
which suffers from the same inconsistency.
Reviewed-by: Sean Eric Fagan <sef@ixsystems.com>
Reviewed-by: Colm Buckley <colm@tuatha.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12261Closes#12276
A couple flags weren't being copied in the case where we're doing size
estimation on a resume.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes: #12266
The receive-o-x_props_override test case reliably fails on the
FreeBSD main builders (but not on Linux), until the root cause is
understood add this test to the FreeBSD exception list.
On Linux the alloc_class_012_pos test case may occasionally fail.
This is a known false positive which has also been added to the
Linux exception list until the test can be made entirely reliable.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12272
ZFS loves using %llu for uint64_t, but that requires a cast to not
be noisy - which is even done in many, though not all, places.
Also a couple places used %u for uint64_t, which were promoted
to %llu.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12233
This reverts commit 13fac09868.
Per the discussion in #11531, the reverted commit---which intended only
to be a cleanup commit---introduced a subtle, unintended change in
behavior.
Care was taken to partially revert and then reapply 10b3c7f5e4
which would otherwise have caused a conflict. These changes were
squashed in to this commit.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Suggested-by: @chrisrd
Suggested-by: robn@despairlabs.com
Signed-off-by: Antonio Russo <aerusso@aerusso.net>
Closes#11531Closes#12227
wmsum was designed exactly for cases like these with many updates
and rare reads. It allows to completely avoid atomic operations on
congested global variables.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12172
This replaces the generic libspl atomic.c atomics implementation
with one based on builtin gcc atomics. This functionality was added
as an experimental feature in gcc 4.4. Today even CentOS 7 ships
with gcc 4.8 as the default compiler we can make this the default.
Furthermore, the builtin atomics are as good or better than our
hand-rolled implementation so it's reasonable to drop that custom code.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11904Closes#12252Closes#12244
In case we have I/O and try to remove an L2ARC device a deadlock might
occur. arc_read()->zio_read()->zfs_blkptr_verify() waits for SCL_VDEV
to be dropped while holding the hash_lock. However, spa_l2cache_load()
holds SCL_ALL and waits for the hash_lock in l2arc_evict().
Fix this by moving zfs_blkptr_verify() to the top top arc_read() before
the hash_lock is taken. Verify the block pointer and return a checksum
error if damaged rather than halting the system, by using
BLK_VERIFY_LOG instead of BLK_VERIFY_HALT.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#12054
Turns out $ZPOOL_IMPORT_OPTS expands in a shell-like fashion,
yielding 'import' '-aN' '-o' 'cachefile=none' for an unset variable,
and 'import' '-aN' '-o' 'cachefile=none' 'word1' 'word2' for a
white-spaced one, but ${ZPOOL_IMPORT_OPTS} expands like "${Z_I_O}"
would in a shell, yielding 'import' '-aN' '-o' 'cachefile=none' ''
(empty) and 'import' '-aN' '-o' 'cachefile=none' 'word1 word2' (spaced)
Fixes eec5ba113e "dracut: 90zfs: respect
zfs_force=1 on systemd systems"
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes: #12231
vdev_draid_min_asize() returns the minimum size of a child vdev. This
is used when determining if a disk is big enough to replace a child.
It's also used by zdb to determine how big of a child to make to test
replacement.
vdev_draid_min_asize() says that the child’s asize has to be at least
1/Nth of the entire draid’s asize, which is the same logic as raidz.
However, this contradicts the code in vdev_draid_open(), which
calculates the draid’s asize based on a reduced child size:
An additional 32MB of scratch space is reserved at the end of each
child for use by the dRAID expansion feature
So the problem is that you can replace a draid disk with one that’s
vdev_draid_min_asize(), but it actually needs to be larger to accommodate
the additional 32MB. The replacement is allowed and everything works at
first (since the reserved space is at the end, and we don’t try to use
it yet), but when you try to close and reopen the pool,
vdev_draid_open() calculates a smaller asize for the draid, because of
the smaller leaf, which is not allowed.
I think the confusion is that vdev_draid_min_asize() is correctly
returning the amount of required *allocatable* space in a leaf, but the
actual *size* of the leaf needs to be at least 32MB more than that.
ztest_vdev_attach_detach() assumes that it can attach that size of
device, and it actually can (the kernel/libzpool accepts it), but it
then later causes zdb to not be able to open the pool.
This commit changes vdev_draid_min_asize() to return the required size
of the leaf, not the size that draid will make available to the metaslab
allocator.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#11459Closes#12221
In zfs_znode_alloc we always hash inodes. If the
znode is unlinked, we do not need to hash it. This
fixes the problem where zfs_suspend_fs is doing zrele
(iput) in an async fashion, and zfs_resume_fs unlinked
drain processing will try to hash an inode that could
still be hashed, resulting in a panic.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alan Somers <asomers@gmail.com>
Signed-off-by: Paul Zuchowski <pzuchowski@datto.com>
Closes#9741Closes#11223Closes#11648Closes#12210
Having an old enough version of "file" and no "uncompress" program
installed can cause rpmbuild as root to crash and mangle rpmdb.
So let's add a build dependency for RPM-based systems.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes: #12071Closes: #12168
Commit 86b5f4c12 added a new zfs_clone_livelist_dedup.ksh test case
but didn't include it in the Makefile.am. This results in the test
not being included in the dist tarball so it's never run by the CI.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes: #12224
This commit partially reverts changes to multilists in PR 7968
(multi-threaded spa-sync()) and adds some cache line alignments to
separate read-only multilists and heavily modified refcount's to
different cache lines.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-by: iXsystems, Inc.
Closes#12158
This mostly reverts "3537 want pool io kstats" commit of 8 years ago.
From one side this code using pool-wide locks became pretty bad for
performance, creating significant lock contention in I/O pipeline.
From another, there are more efficient ways now to obtain detailed
statistics, while this statistics is illumos-specific and much less
usable on Linux and FreeBSD, reported only via procfs/sysctls.
This commit does not remove KSTAT_TYPE_IO implementation, that may
be removed later together with already unused KSTAT_TYPE_INTR and
KSTAT_TYPE_TIMER.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12212
The prevailing style is to use either nothing, or the originating
organisational umbrella (here: OpenZFS), and these aren't Linux manpages
This also deduplicates the substitution code, and makes adding/removing
sexions simpler in future
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12212
The first warning of a misspelling is a false positive, so we annotate
the script accordingly. As for the x-prefix warnings update the check
to use the conventional '[ -z <string> ]' syntax.
all-syslog.sh:46:47: warning: Possible misspelling: ZEVENT_ZIO_OBJECT
may not be assigned, but ZEVENT_ZIO_OBJSET is. [SC2153]
make_gitrev.sh:53:6: note: Avoid x-prefix in comparisons as it no
longer serves a purpose [SC2268]
man-dates.sh:10:7: note: Avoid x-prefix in comparisons as it no
longer serves a purpose [SC2268]
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12208
This:
(a) improves the error log message,
(b) locks per pool instead of globally,
(c) locks the actual output file instead of /var/lock/zfs-list,
which would otherwise linger there forever (well, still will,
but you can remove it and it won't come back), and
(d) preserves attributes of the output file
instead of reverting them to 0:0 644
It is imperative that the previous commit
("zed-functions.sh: zed_lock(): don't truncate lock")
be included in any series that contains this one
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12042
By locking the log file itself, we can omit arduous rebinding and
explicit umask setting, but, perhaps more importantly, avoid permanently
littering /var/lock/ with zed.debug.log.lock we will never delete
It is imperative that the previous commit
("zed-functions.sh: zed_lock(): don't truncate lock")
be included in any series that contains this one
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12042
By appending instead of truncating, we can lock on any file (with write
permissions) instead of only dedicated lock files, since the locking
process itself no longer alters the file in any way
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12042
`getfsstat(2)` is used to retrieve the list of mounted file systems,
which libzfs uses when fetching properties like mountpoint, atime,
setuid, etc. The `mode` parameter may be `MNT_NOWAIT`, which uses
information in the VFS's cache, or `MNT_WAIT`, which effectively does a
`statfs` on every single mounted file system in order to fetch the most
up-to-date information. As far as I can tell, the only fields that
libzfs cares about are the filesystem's name, mountpoint, fstypename,
and mount flags. Those things are always updated on mount and unmount,
so they will always be accurate in the VFS's mount cache except in two
circumstances:
1) When a file system is busy unmounting
2) When a ZFS file system changes the value of a mount-overridable
property like atime or setuid, but doesn't remount the file system.
Right now that only happens when the property is changed by an
unprivileged user who has delegated authority to change the property
but not to mount the dataset. But perhaps libzfs could choose to do
it for other reasons in the future.
Switching to `MNT_NOWAIT` will greatly improve speed with no downside,
as long as we explicitly update the mount cache whenever we change a
mount-overridable property.
For comparison, Illumos gets this information using the native
`getmntany` and `getmntent` functions, which also use cached
information. The illumos function that would refresh the cache,
`resetmnttab`, is never called by libzfs.
And on GNU/Linux, `getmntany` and `getmntent` don't even communicate
with the kernel directly. They simply parse the file they are given,
which is usually /etc/mtab or /proc/mounts. Perhaps the implementation
of /proc/mounts is synchronous, ala MNT_WAIT; I don't know.
Sponsored-by: Axcient
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alan Somers <asomers@gmail.com>
Closes: #12091
There's already logic to force INVARIANTS on for building if it's
present in the running kernel; however, not having DEBUG enabled
when DEBUG and INVARIANTS are can cause strange panics.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12185Closes#12163
Update the logic to handle the dedup-case of consecutive
FREEs in the livelist code. The logic still ensures that
all the FREE entries are matched up with a respective
ALLOC by keeping a refcount for each FREE blkptr that we
encounter and ensuring that this refcount gets to zero
by the time we are done processing the livelist.
zdb -y no longer panics when encountering double frees
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Don Brady <don.brady@delphix.com>
Signed-off-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Closes#11480Closes#12177
- Avoid atomic_add() when updating as_lower_bound/as_upper_bound.
Previous code was excessively strong on 64bit systems while not
strong enough on 32bit ones. Instead introduce and use real
atomic_load() and atomic_store() operations, just an assignments
on 64bit machines, but using proper atomics on 32bit ones to avoid
torn reads/writes.
- Reduce number of buckets on large systems. Extra buckets not as
much improve add speed, as hurt reads. Unlike wmsum for aggsum
reads are still important.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12145
SUSE stores the library at /lib64/libgcc_s.so.1 (/lib/libgcc_s.so.1 for
i686 glibc), which is in the search path
Also relax the /usr/lib path to catch systems similar to SUSE
(/usr/lib64/gcc/x86_64-suse-linux/10/libgcc_s.so) but without
the top-level lib64
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11750Closes#12108
In the current world, `zfs diff` will die on certain kinds of errors
that come up on ordinary, not-mangled filesystems - like EINVAL,
which can come from a file with multiple hardlinks having the one
whose name is referenced deleted.
Since it should always be safe to continue, let's relax about all
error codes - still print something for most, but don't immediately
abort when we encounter them.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12072
VFS_QUOTACTL(9) has been updated to allow each filesystem to indicate
whether it has changed the busy state of the mount. The filesystem
may still assume that its .vfs_quotactl entrypoint is always called
with the mount busied, but only needs to unbusy the mount (and clear
*mp_busy) if it does something that actually requires the mount to be
unbusied. It no longer needs to blindly copy-paste the UFS protocol
for calling vfs_unbusy(9) for the Q_QUOTAOFF and Q_QUOTAON commands.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Jason Harmening <jason.harmening@gmail.com>
Closes#12052
Move check for errors from mbrtowc() into the loop. The error values
are not actually negative, so we don't break out of the loop when they
are encountered.
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#12175Closes#12176
For small objects the kernel's slab implementation is very fast and
space efficient. However, as the allocation size increases to
require multiple pages performance suffers. The SPL kmem cache
allocator was designed to better handle these large allocation
sizes. Therefore, on Linux the kmem_cache_* compatibility wrappers
prefer to use the kernel's slab allocator for small objects and
the custom SPL kmem cache allocator for larger objects.
This logic was effectively disabled for all architectures using
a non-4K page size which caused all kmem caches to only use the
SPL implementation. Functionally this is fine, but the SPL code
which calculates the target number of objects per-slab does not
take in to account that __vmalloc() always returns page-aligned
memory. This can result in a massive amount of wasted space when
allocating tiny objects on a platform using large pages (64k).
To resolve this issue we set the spl_kmem_cache_slab_limit cutoff
to 16K for all architectures.
This particular change does not attempt to update the logic used
to calculate the optimal number of pages per slab. This remains
an issue which should be addressed in a future change.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12152Closes#11429Closes#11574Closes#12150
In `zpool_load_compat()`:
* initialize `l_features[]` with a loop rather than a static
initializer.
* don't redefine system constants; use private names instead
Rationale here:
When an array is initialized using a static {foo}, only the specified
members are initialized to the provided values, the rest are
initialized to zero. While B_FALSE is of course zero, it feels
unsafe to rely on this being true forever, so I'm inclined to sacrifice
a few microseconds of runtime here and initialize using a loop.
When looking for the correct combination of system constants to use
(in open() and mmap()), I prefer to use private constants rather than
redefining system ones; due to the small chance that the system
ones might be referenced later in the file. So rather than defining
O_PATH and MAP_POPULATE, I use distinct constant names.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Colm Buckley <colm@tuatha.org>
Closes#12156
zfs_arc_overflow_shift was never a parameter:
ca0bf58d65 ("Illumos 5497 - lock
contention on arcs_mtx") is the only result in
git log -Soverflow_shift, and it wasn't exposed then, nor is it now
zfs_read_chunk_size was renamed to zfs_vnops_read_chunk_size in
e53d678d4a ("Share zfs_fsync, zfs_read,
zfs_write, et al between Linux and FreeBSD")
zio_decompress_fail_fraction was never a parameter: it was added in
c3bd3fb4ac ("OpenZFS 9403 - assertion
failed in arc_buf_destroy()") as a developer aid for setting in zdb, but
it's a dangerous test tunable and has no place in public documentation,
(not to mention that it obviously doesn't work):
> Although this did uncover a few low priority issues, this
unfortuantely also causes ztest to ASSERT in many locations where the
code is working correctly since it is designed to fail on IO errors.
Developers can manually set this variable with the '-o' option to find
and debug issues.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12157
It turns out that sometimes, evidently only when run inside the
ZTS handler, arc_summary3 | head > /dev/null will die with ENOTCONN,
and ruin the test run.
Added handling for that.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12160
There used to be a warning after upgrading a zpool in FreeBSD, so users
won't forget to update the boot loader that pool is booted from.
This change brings this warning back, but only if the bootfs property
is set on the pool, which should be sufficient for the vast majority of
FreeBSD installations. People running something custom are most likely
aware of what to do after an upgrade in their specific environment.
Functionality is implemented in an OS specific helper function.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Co-authored-by: Michael Gmelin <grembo@FreeBSD.org>
Signed-off-by: Michael Gmelin <grembo@FreeBSD.org>
Closes#12099Closes#12104
The additional iter advance is incorrect, as copy_from_iter() has
already done the right thing. This will result in the following
warning being printed to the console as of the 5.12 kernel.
Attempted to advance past end of bvec iter
This change should have been included with #11378 when a
similar change was made on the read side.
Suggested-by: @siebenmann
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Issue #11378Closes#12041Closes#12155
make_gitrev.sh actually breaks checkbashisms' parser,
which /insists/ that the end-of-line " is actually a string start
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12101
This checks every file it checked (and a few more),
but explicitly instead of "if it works it works" best-effort
(which wasn't that good anyway)
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#10512Closes#12101
Accidentally introduced by commit dd00925e8d.
Force-install the zstreamdump link, this is a supported configuration
and the install should not fail if it needs to overwrite an existing
file.
Also cd to work around some funny platforms as noted in AC_PROG_LN_S doc
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12143
Also rip out the section about potentially including in the OpenZFS
distribution and simplify -e description
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12125
I fixed a few typos, but avoided changing anything beyond that;
the sould of the document should be preserved
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12125
This change introduces long options for ztest. It builds the usage
message as well as the long_options array from a single table. It also
adds #defines for the default values.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Manoj Joseph <manoj.joseph@delphix.com>
Closes#12117
While Libera doesn't yet have a webchat client, we should at least
direct them to the right network. Once a webchat client is available,
we can direct them to it.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#12127
wmsum counters are a reduced version of aggsum counters, optimized for
write-mostly scenarios. They do not provide optimized read functions,
but instead allow much cheaper add function. The primary usage is
infrequently read statistic counters, not requiring exact precision.
The Linux implementation is directly mapped into percpu_counter KPI.
The FreeBSD implementation is directly mapped into counter(9) KPI.
In user-space due to lack of better implementation mapped to aggsum.
Unfortunately neither Linux percpu_counter nor FreeBSD counter(9)
provide sufficient functionality to completelly replace aggsum, so
it still remains to be used for several hot counters.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12114
Previously, ZFS scaled maxinflight_bytes based on total number of
disks in the pool. A 3-wide mirror was receiving a queue depth of 3
disks, which it should not, since it reads from all the disks inside.
For wide raidz the situation was slightly better, but still a 3-wide
raidz1 received a depth of 3 disks instead of 2.
The new code counts only unique data disks, i.e. 1 disk for mirrors
and non-parity disks for raidz/draid. For draid the math is still
imperfect, since vdev_get_nparity() returns number of parity disks
per group, not per vdev, but still some better than it was.
This should slightly reduce scrub influence on payload for some pool
topologies by avoiding excessive queuing.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closing #12046
A plain rewrite of the shell version, and generates identical
units, save for replacing some empty lines with nothing, having fewer
meaningless spaces in After=s and different spacing in the lock scripts,
for a clean git diff -w
This is a gain of anywhere from 0m0.336s vs 0m0.022s (15.27x)
to 0m0.202s vs 0m0.006s (33.67x), depending on the hardware,
a.k.a. from "absolutely unusable" to "perfectly fine"
This also properly deals with canmount=noauto units across multiple
pools
See PR for detailed timings (of an early version) and diffs
Reviewed-by: Antonio Russo <aerusso@aerusso.net>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: InsanePrawn <insane.prawny@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Issue #11915Closes#11917
zstreamdump(8) was in quite a bad state,
and the wrapper didn't work if invoked without /sbin in $PATH
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12015
This produces a leaner image, doesn't fail if zdb doesn't exist,
properly handles hostnameless systems, doesn't mention crypto modules
for no reason, doesn't add useless empty executable in hopes an
eight-year-old PR is merged, uses i-t builtins for all copies
Also optimize the checkbashisms filter to spawn one (or a few) awks
instead of one per regular file and remove initramfs/hooks therefrom due
to a command -v false positive
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12017
configure on s390x has a key check fail with an error about
a variable being used uninitialized. So let's initialize it.
Reviewed-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12126
Just like #12087, the set_acl signature changed with all the bolted-on
*userns parameters, which disabled set_acl usage, and caused #12076.
Turn zpl_set_acl into zpl_set_acl and zpl_set_acl_impl, and add a
new configure test for the new version.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12076Closes#12093
Linux man-pages' mount(8) points at fcntl(2), as does mount(2),
and support for it is little-used, deprecated, and configurable
since 4.5.
As far as I can tell, FreeBSD doesn't support nbmand at all ‒
mandatory locks are mostly dead
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12111
Previous commit added accounting for geom mode, but not for dev.
In geom mode we actually have GEOM statistics, while in dev mode
additional accounting actually makes more sense.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#12097
ZFS does not expect transient errors from crypto. For read they are
counted as checksum errors, while for write end up in panic. To not
panic on random low memory conditions retry ENOMEM errors in the OCF
wrapper function.
While there remove unneeded timeout and priority from msleep().
External-issue: https://reviews.freebsd.org/D30339
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12077
I looked for a bit, and couldn't find any documentation on
how to print all logged dbgmsg entries, just messages since
the DTrace probe started, until @allanjude kindly pointed me
toward the sysctl.
So let's add that note where the DTrace probe is mentioned for
FreeBSD, so other people can find it.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12113
Linux changed the tmpfile() signature again in torvalds/linux@6521f89,
which in turn broke our HAVE_TMPFILE detection in configure.
Update that macro to include the new case, and change the signature of
zpl_tmpfile as appropriate.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes: #12060Closes: #12087
This change addresses two distinct scenarios which are possible
when performing a sequential resilver to a dRAID pool with vdevs
that contain silent unknown damage. Which in this circumstance
took the form of the devices being intentionally overwritten with
zeros. However, it could also result from a device returning incorrect
data while a sequential resilver was in progress.
Scenario 1) A sequential resilver is performed while all of the
dRAID vdevs are ONLINE and there is silent damage present on the
vdev being resilvered. In this case, nothing will be repaired
by vdev_raidz_io_done_reconstruct_known_missing() because
rc->rc_error isn't set on any of the raid columns. To address
this vdev_draid_io_start_read() has been updated to always mark
the resilvering column as ESTALE for sequential resilver IO.
Scenario 2) Multiple columns contain silent damage for the same
block and a sequential resilver is performed. In this case it's
impossible to generate the correct data from parity unless all of
the damaged columns are being sequentially resilvered (and thus
only good data is used to generate parity). This is as expected
and there's nothing which can be done about it. However, we need
to be careful not to make to situation worse. Since we can't
verify the data is actually good without a checksum, we must
only repair the devices which are being sequentially resilvered.
Otherwise, an incorrect repair to a device which previously
contained good data could effectively lock in the damage and
make reconstruction impossible. A check for this was added to
vdev_raidz_io_done_verified() along with a new test case.
Lastly, this change updates the redundancy_draid_spare1 and
redundancy_draid_spare3 test cases to be more representative
of normal dRAID replacement operation. Specifically, what we
care about is that the scrub run after a sequential resilver
does not find additional blocks which need repair. This would
indicate the sequential resilver failed to rebuild a section of
one of the devices. Note also the tests were switched to using
the verify_pool() function which still checks for checksum errors.
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12061
While use of dynamic taskqs allows to reduce number of idle threads,
hardcoded 8 taskqs of each kind is a big overkill for small systems,
complicating CPU scheduling, increasing I/O reorder, etc, while
providing no real locking benefits, just not needed there.
On another side, 12*8 worker threads per kind are able to overload
almost any system nowadays. For example, pool of several fast SSDs
with SHA256 checksum makes system barely responsive during scrub, or
with dedup enabled barely responsive during large file deletion.
To address both problems this patch introduces ZTI_SCALE macro, alike
to ZTI_BATCH, but with multiple taskqs, depending on number of CPUs,
to be used in places where lock scalability is needed, while request
ordering is not so much. The code is made to create new taskq for
~6 worker threads (less for small systems, but more for very large)
up to 80% of CPU cores (previous 75% was not good for rounding down).
Both number of threads and threads per taskq are now tunable in case
somebody really wants to use all of system power for ZFS.
While obviously some benchmarks show small peak performance reduction
(not so big really, especially on systems with SMT, where use of the
second threads does not give as much performance as the first ones),
they also show dramatic latency reduction and much more smooth user-
space operation in case of high CPU usage by ZFS.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#11966
The redundancy_draid.ksh and redundancy_raidz.ksh tests were updated
by commit 93c8e91fe to additionally verify self-healing. This
additional check increased the run time which can now occasionally
exceed the default maximum timeout in the CI environment. To prevent
this from causing failures increase the default timeout for the
redundancy test cases.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12043
The kernel will use the xattr property by default when not overridden
by a mount option.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11997
Commit d1d4769 takes into account the encryption key version to
decide if the local_mac could be zeroed out. However, this could lead
to failure mounting encrypted datasets created with intermediate
versions of ZFS encryption available in master between major releases.
In order to prevent this situation revert d1d4769 pending a more
comprehensive fix which addresses the mount failure case.
Reviewed-by: George Amanakis <gamanakis@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #11294
Issue #12025
Issue #12300Closes#12033
mandoc: ./man/man8/zfs-mount-generator.8.in:188:2:
ERROR: skipping end of block that is not open: RE
mandoc: ./man/man8/zfs_ids_to_path.8:38:2:
ERROR: skipping unknown macro: .LP
mandoc: ./man/man8/zfs_ids_to_path.8:48:2:
ERROR: inserting missing end of block: Sh breaks Bl
mandoc: ./man/man8/zfs-wait.8:69:2:
ERROR: skipping end of block that is not open: El
mandoc: ./man/man8/zfs-program.8:460:2:
ERROR: inserting missing end of block: It breaks Bd
mandoc: ./man/man8/zfs-mount-generator.8:188:2:
ERROR: skipping end of block that is not open: RE
mandoc: ./man/man8/zstream.8:43:2:
ERROR: skipping unknown macro: .LP
mandoc: ./man/man8/zstream.8:107:2:
ERROR: inserting missing end of block: Sh breaks Bl
mandoc: ./man/man8/zstream.8:107:2:
ERROR: inserting missing end of block: Sh breaks Bl
make: *** [Makefile:1529: mancheck] Error 1
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Issue #12017
The following seven tests been observed to occasionally fail during
CI testing. This commit adds them to the list of known somewhat
flaky test cases.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12023
Linux kernel commit 0f00b82e5413571ed225ddbccad6882d7ea60bc7 removes the
revalidate_disk() handler from struct block_device_operations. This
caused a regression, and this commit eliminates the call to it and the
assignment in the block_device_operations static handler assignment
code, when configure identifies that the kernel doesn't support that
API handler.
Reviewed-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#11967Closes#11977
zfs_zevent_console committed multiple printk()s per line without
properly continuing them ‒ a single event could easily be fragmented
across over thirty lines, making it useless for direct application
zfs_zevent_cols exists purely to wrap the output from zfs_zevent_console
The niche this was supposed to fill can be better served by something
akin to the all-syslog ZEDLET
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#7082Closes#11996
Also always free tmp2 at the end
Before:
nabijaczleweli@tarta:~/uwu$ valgrind --leak-check=full ./blergh
==8947== Memcheck, a memory error detector
==8947== Using Valgrind-3.14.0 and LibVEX
==8947== Command: ./blergh
==8947==
(null)
==8947==
==8947== HEAP SUMMARY:
==8947== in use at exit: 23 bytes in 1 blocks
==8947== total heap usage: 3 allocs, 2 frees, 1,147 bytes allocated
==8947==
==8947== 23 bytes in 1 blocks are definitely lost in loss record 1 of 1
==8947== at 0x483577F: malloc (vg_replace_malloc.c:299)
==8947== by 0x48D74B7: vasprintf (vasprintf.c:73)
==8947== by 0x48B7833: asprintf (asprintf.c:35)
==8947== by 0x401258: zfs_get_enclosure_sysfs_path
(zutil_device_path_os.c:191)
==8947== by 0x401482: main (blergh.c:107)
==8947==
==8947== LEAK SUMMARY:
==8947== definitely lost: 23 bytes in 1 blocks
==8947== indirectly lost: 0 bytes in 0 blocks
==8947== possibly lost: 0 bytes in 0 blocks
==8947== still reachable: 0 bytes in 0 blocks
==8947== suppressed: 0 bytes in 0 blocks
==8947==
==8947== For counts of detected and suppressed errors, rerun with: -v
==8947== ERROR SUMMARY: 1 errors from 1 contexts (suppressed: 0 from 0)
nabijaczleweli@tarta:~/uwu$ sed -n 191p zutil_device_path_os.c
tmpsize = asprintf(&tmp1, "/sys/block/%s/device", dev_name);
After:
nabijaczleweli@tarta:~/uwu$ valgrind --leak-check=full ./blergh
==9512== Memcheck, a memory error detector
==9512== Using Valgrind-3.14.0 and LibVEX
==9512== Command: ./blergh
==9512==
(null)
==9512==
==9512== HEAP SUMMARY:
==9512== in use at exit: 0 bytes in 0 blocks
==9512== total heap usage: 3 allocs, 3 frees, 1,147 bytes allocated
==9512==
==9512== All heap blocks were freed -- no leaks are possible
==9512==
==9512== For counts of detected and suppressed errors, rerun with: -v
==9512== ERROR SUMMARY: 0 errors from 0 contexts (suppressed: 0 from 0)
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11993
As a bonus, this also passes the open flags into the open flags instead
of the mode (it worked by accident because O_RDONLY is 0),
correctly detects a failed map,
and prefaults the entire file since we're always writing to every page
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11993
This commits contains changes to allow running `copy-builtin` without
bash + some minor improvements.
changed shebang to /bin/sh
added -f option to `set` to globally disable unneeded globbing
replaced all `echo` commands within add_after() with `printf`
alternative to avoid possible issues with options (-neE)
dropped non-portable superfluous `readlink` command
replaced superfluous `true` command with `:` builtin alternative
replaced non-portable `--recursive` option of `cp` command with `-R`
alternative
dropped non-portable `local` keyword
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: illiliti <illiliti@protonmail.com>
Closes#12004
When dRAID performs a normal read operation only the data columns
in the raid map are read from disk. This is enough information to
calculate the checksum, verify it, and return the needed data to the
application. It's only in the event of a checksum failure that the
additional parity and any empty columns must be read since they are
required for parity reconstruction.
Reading these additional columns is handled by vdev_raidz_read_all()
which calls vdev_draid_map_alloc_empty() to expand the raid_map_t
and submit IOs for the missing columns. This all works correctly,
but it fails to account for any "short" columns. These are data
columns which are padded with a empty skip sector at the end.
Since that empty sector is not needed for a normal read it's not
read when columns is first read from disk. However, like the parity
and empty columns the skip sector is needed to perform reconstruction.
The fix is to mark any "short" columns as never being read by clearing
the rc_tried flag when expanding the raid_map_t. This will cause
the entire column to re-read from disk in the event of a checksum
failure allowing the self-healing functionality to repair the block.
Note that this only effects the self-healing feature because when
scrubbing a pool the parity, data, and empty columns are all read
initially to verify their contents. Furthermore, only blocks which
contain "short" columns would be effected, and only when the memory
backing the skip sector wasn't already zeroed out.
This change extends the existing redundancy_raidz.ksh test case to
verify self-healing (as well as resilver and scrub). Then applies
the same test case to dRAID with a slightly modified version of
the test script called redundancy_draid.ksh. The unused variable
combrec was also removed from both test cases.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12010
Afterward, git grep ZoL matches:
* README.md: * [ZoL Site](https://zfsonlinux.org)
- Correct
* etc/default/zfs.in:# ZoL userland configuration.
- Changing this would induce a needless upgrade-check,
if the user has modified the configuration;
this can be updated the next time the defaults change
* module/zfs/dmu_send.c: * ZoL < 0.7 does not handle [...]
- Before 0.7 is ZoL, so fair enough
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Issue #11956
zfs_log_create returns void, so there is no reason to cast its return
value to void at the call site.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11994
This can be very easily triggered by adding a sleep(1) before
the wait4() on a PID-starved system: the reaper thread would wait
for a child before its entry appeared, letting old entries accumulate:
Invoking "all-debug.sh" eid=3021 pid=391
Finished "(null)" eid=0 pid=391 time=0.002432s exit=0
Invoking "all-syslog.sh" eid=3021 pid=336
Finished "(null)" eid=0 pid=336 time=0.002432s exit=0
Invoking "history_event-zfs-list-cacher.sh" eid=3021 pid=347
Invoking "all-debug.sh" eid=3022 pid=349
Finished "history_event-zfs-list-cacher.sh" eid=3021 pid=347
time=0.001669s exit=0
Finished "(null)" eid=0 pid=349 time=0.002404s exit=0
Invoking "all-syslog.sh" eid=3022 pid=370
Finished "(null)" eid=0 pid=370 time=0.002427s exit=0
Invoking "history_event-zfs-list-cacher.sh" eid=3022 pid=391
avl_find(tree, new_node, &where) == NULL
ASSERT at ../../module/avl/avl.c:641:avl_add()
Thread 1 "zed" received signal SIGABRT, Aborted.
By employing this wider lock, we atomise [wait, remove] and [fork, add]:
slowing down the reaper thread now just causes some zombies
to accumulate until it can get to them
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Don Brady <don.brady@delphix.com>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11963Closes#11965
Quoting <linux/exportfs.h>:
> encode_fh() should return the fileid_type on success and on error
> returns 255 (if the space needed to encode fh is greater than
> @max_len*4 bytes). On error @max_len contains the minimum size (in 4
> byte unit) needed to encode the file handle.
ZFS was not setting max_len in the case where the handle was too
small. As a result of this, the `t_name_to_handle_at.c' example in
name_to_handle_at(2) did not work on ZFS.
zfsctl_fid() will itself set max_len if called with a fid that is too
small, so if we give zfs_fid() that behavior as well, the fix is quite
easy: if the handle is too small, just use a zero-size fid instead of
the handle.
Tested by running t_name_to_handle_at on a normal file, a directory, a
.zfs directory, and a snapshot.
Thanks-to: Puck Meerburg <puck@puckipedia.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Alyssa Ross <hi@alyssa.is>
Closes#11995
Previous code tried to keep prefetch streams while moving dnode. But
it was at least not updating per-stream zs_fetchback pointers, causing
use-after-free on next access. Instead of that I see much easier and
cleaner to just drop old prefetch state and start new from scratch.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#11936Closes#11998
zp->z_lock is used in shared code for protecting projid and scantime.
We don't exercise these paths much if at all on FreeBSD, so have been
lucky enough not to have issues with the uninitialized locks so far.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#12003
Changed the default specified for zfs_dbgmsg_enable, added
clarification of interaction with zfs_flags.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#11984Closes#11986
Also minor clean-up with folding state_to_val() into a case,
unrolling the lesser-available seq into numbers,
ignoring vdev states we don't care about,
and documentation comments
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11934Closes#11935
IS_XATTRDIR is never used.
v_count is only used in two places, one immediately followed by the
use of the real name, v_usecount.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#11973
This ensures that we don't accumulate checksum errors against offline or
unavailable devices but, more importantly, means that we don't
needlessly create DTL entries for offline devices that are already
up-to-date.
Consider a 3-way mirror, with disk A always online (and so always with
an empty DTL) and B and C only occasionally online. When A & B resilver
with C offline, B's DTL will effectively be appended to C's due to these
spurious ZIOs even as the resilver empties B's DTL:
* These ZIOs land in vdev_mirror_scrub_done() and flag an error
* That flagged error causes vdev_mirror_io_done() to see
unexpected_errors, so it issues a ZIO_TYPE_WRITE repair ZIO, which
inherits ZIO_FLAG_SCAN_THREAD because zio_vdev_child_io() includes
that flag in ZIO_VDEV_CHILD_FLAGS.
* That ZIO fails, too, and eventually zio_done() gets its hands on it
and calls vdev_stat_update().
* vdev_stat_update() sees the error and this zio...
* is not speculative,
* is not due to EIO (but rather ENXIO, since the device is closed)
* has an ->io_vd != NULL (specifically, the offline leaf device)
* is a write
* is for a txg != 0 (but rather the read block's physical birth txg)
* has ZIO_FLAG_SCAN_THREAD asserted
* So: vdev_stat_update() calls vdev_dtl_dirty() on the offline vdev.
Then, when A & C resilver with B offline, that story gets replayed and
C's DTL will be appended to B's.
In fact, one does not need this permanently-broken-mirror scenario to
induce badness: breaking a mirror with no DTLs and then scrubbing will
create DTLs for all offline devices. These DTLs will persist until the
entire mirror is reassembled for the duration of the *resilver*, which,
incidentally, will not consider the devices with good data to be sources
of good data in the case of a read failure.
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Nathaniel Wesley Filardo <nwfilardo@gmail.com>
Closes#11930
In Fedora 28 the packaging guidelines were changed such that ldconfig
should no longer be called in either the %post or %postun scriptlets.
Instead the new compatibility macros %ldconfig_post, %ldconfig_postun,
and %ldocnfig_scriptlets should be used.
Since we only currently support Fedora 31 and newer, we could drop
%post or %postun scriptlets entirely according to the guidelines.
However, since we also use the same spec file for CentOS / RHEL
it's convenient to call the macros which are available starting
with CentOS / RHEL 8. For CentOS / RHEL 7 we must still call
ldconfig in the traditional way.
https://fedoraproject.org/wiki/Changes/Removing_ldconfig_scriptlets
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11931
If zdb is not built with DEBUG mode, the ASSERT macros will be
eliminated.
This will leave vim defined, but not used (gcc warning) and
checkpoint spacemap validation loop will do nothing.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Toomas Soome <tsoome@me.com>
Closes#11932
Both the zpool_initialize_import_export and checkpoint_discard_busy
test cases a known to occasionally fail. Add them to the list of
known possible failures and reference the appropriate issue on the
tracker.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11949
Receiving datasets while blanket inheriting properties like zfs
receive -x mountpoint can generally be desirable, e.g. to avoid
unexpected mounts on backup hosts.
Currently this will fail to receive zvols due to the mountpoint
property being applicable to filesystems only. This limitation
currently requires operators to special-case their minds and tools
for zvols.
This change gets rid of this limitation for inherit (-x) by
Spiting up the dataset type handling: Warnings for inheriting (-x),
errors for overriding (-o).
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: InsanePrawn <insane.prawny@gmail.com>
Closes#11416Closes#11840Closes#11864
Introduce a specific valid function for avx512f+avx512bw (instead
of checking only for avx512f).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Adam Moss <c@yotes.com>
Signed-off-by: Romain Dolbeau <romain@dolbeau.org>
Closes#11937Closes#11938
As soon as wait4() returns, fork() can immediately return with the same
PID, and race to lock _launched_processes_lock, then try to add the new
(duplicate) PID to _launched_processes, which asserts
By locking before wait4(), we ensure, that, given that same
unfortunate scheduling, _launched_processes_lock cannot be locked by the
spawner before we pop the process in the reaper, and only afterward will
it be added
This moves where the reaper idles when there are children from the
wait4() to the pause(), locking for the duration of that single syscall
in both the no-children and running-children cases; the impact of this
is one to two syscalls (depending on _launched_processes_lock state)
per loop
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Don Brady <don.brady@delphix.com>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11924Closes#11928
The special_small_blocks section directed readers to zpool(8) for
documentation on special allocation classes, while they are actually
documented in zpoolconcepts(8).
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Daniel Stevenson <daniel@dstev.net>
Closes#11918
If $FSLIST exists but is empty, the generator fails with
sort: cannot read: '/etc/zfs/zfs-list.cache/*':
No such file or directory
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11915
- Add additional logging to provide more information about why the
test failed. This including logging more of the individual commands
and the contents and differences of the record files on failure.
- Updated get_vdevs() to properly exclude all top-level vdevs
including raidz3 and draid[1-3].
- Replaced gnudd with dd. This is the only remaining place in the
test suite gnudd is used and it shouldn't be needed.
- The refill_test_env function expects the pool as the first argument
but never sets the pool variable.
- Only fill the test pools to 50% of capacity instead of 75% to help
speed up the tests.
- Fix replace_missing_devs() calculation, MINDEVSIZE should be
MINVDEVSIZE.
- Fix damage_devs() so it overwrites almost all of the device so
we're guaranteed to damage filesystem blocks.
- redundancy_stripe.ksh should not use log_mustnot to check if the
pool is healthy since the return value may be misinterpreted.
Just perform a normal conditional check and log the failure.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11906
Objtool requires the use of a DRAP register while aligning the
stack. Since a DRAP register is a gcc concept and we are
notoriously low on registers in the crypto code, it's not worth
the effort to mimic gcc generated stack realignment.
We simply silence the warning by adding the offending object files
to OBJECT_FILES_NON_STANDARD.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Attila Fülöp <attila@fueloep.org>
Closes#6950Closes#11914
This deduplicates 2 sets of caches which use the same allocation size.
Memory savings fluctuate a lot, one sample result is FreeBSD running
"make buildworld" saving ~180MB RAM in reduced page count associated
with zio caches.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#11877
This partly mirrors what the i-t script does (though that mounts all
children, recursively) ‒ /etc, /usr, /lib*, and /bin are all essential,
if present, to successfully invoke the real init, which will then mount
everything else it might need in the right order
The following extreme-case set-up boots w/o issues now:
/ zoot zfs rw,relatime,xattr,noacl
├─/etc zoot/etc zfs rw,relatime,xattr,noacl
├─/usr zoot/usr zfs rw,relatime,xattr,noacl
│ └─/usr/local zoot/usr/local zfs rw,relatime,xattr,noacl
├─/var zoot/var zfs rw,relatime,xattr,noacl
│ ├─/var/lib zoot/var/lib zfs rw,relatime,xattr,noacl
│ ├─/var/log zoot/var/log zfs rw,relatime,xattr,posixacl
│ ├─/var/cache zoot/var/cache zfs rw,relatime,xattr,noacl
│ └─/var/tmp zoot/var/tmp zfs rw,relatime,xattr,noacl
├─/home zoot/home zfs rw,relatime,xattr,noacl
│ └─/home/nab zoot/home/nab zfs rw,relatime,xattr,noacl
├─/boot zoot/boot zfs rw,relatime,xattr,noacl
├─/root zoot/home/root zfs rw,relatime,xattr,noacl
├─/opt zoot/opt zfs rw,relatime,xattr,noacl
└─/srv zoot/srv zfs rw,relatime,xattr,noacl
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11898
"debug" is also used by systemd itself, and there's really no reason for
the generator to write this much garbage by default
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11898
Fix NULL pointer dereference when reporting
checksum error for gang block in zio_done.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Zuchowski <pzuchowski@datto.com>
Closes#11872Closes#11896
Fixes get_system_hostid() if it was set via the aforementioned sysctl
and simplifies the code a bit. The kernel and user-space must agree,
after all.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11879
This fixes /proc/sys/kernel/spl/hostid on kernels with mainline commit
32927393dc1ccd60fb2bdc05b9e8e88753761469 ("sysctl: pass kernel pointers
to ->proc_handler") ‒ 5.7-rc1 and up
The access_ok() check in copy_to_user() in proc_copyout_string() would
always fail, so all userspace reads and writes would fail with EINVAL
proc_dostring() strips only the final new-line,
but simple_strtoul() doesn't actually need a back-trimmed string ‒
writing "012345678 \n" is still allowed, as is "012345678zupsko", &c.
This alters what happens when an invalid value is written ‒
previously it'd get set to what-ever simple_strtoul() returned
(probably 0, thereby resetting it to default), now it does nothing
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11878Closes#11879
Traversal code, traverse_visitbp() does visit blocks recursively.
Indirect (Non L0) Block of size 128k could contain, 1024 block pointers
of 128 bytes. In case of full traverse OR incremental traverse, where
all blocks were modified, it could traverse large number of blocks
pointed by indirect. Traversal code does issue prefetch of blocks
traversed below indirect. This could result into large number of
async reads queued on vdev queue. So, account for prefetch issued for
blocks pointed by indirect and limit max prefetch in one go.
Module Param:
zfs_traverse_indirect_prefetch_limit: Limit of prefetch while traversing
an indirect block.
Local counters:
prefetched: Local counter to account for number prefetch done.
pidx: Index for which next prefetch to be issued.
ptidx: Index at which next prefetch to be triggered.
Keep "ptidx" somewhere in the middle of blocks prefetched, so that
blocks prefetch read gets the enough time window before their demand
read is issued.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Jitendra Patidar <jitendra.patidar@nutanix.com>
Closes#11802Closes#11803
This change adds SIGSTOP and SIGTSTP handling to the issig function;
this mirrors its behavior on Solaris. This way, long running kernel
tasks can be stopped with the appropriate signals. Note that doing
so with ctrl-z on the command line doesn't return control of the tty
to the shell, because tty handling is done separately from stopping
the process. That can be future work, if people feel that it is a
necessary addition.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Issue #810
Issue #10843Closes#11801
The awk command used by the checkbashisms target incorrectly
adds the escape character before the ! and # characters. This
results in the following warnings because these characters do not
need to be escaped.
awk: cmd. line:1: warning: regexp escape sequence
`\!' is not a known regexp operator
awk: cmd. line:1: warning: regexp escape sequence
`\#' is not a known regexp operator
Remove the unneeded escape character before ! and #.
Valid escape sequences are:
https://www.gnu.org/software/gawk/manual/html_node/Escape-Sequences.html
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11902
Do not (incorrectly, right instead left) pad health string itself,
it will be taken care of when printing property value below.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Yuri Pankov <yuripv@FreeBSD.org>
Closes#11899
Follow up to d5ef91af which adds a missing 'obsoletes' for the
libzfs-devel package.
Add a comment to the zfs.spec file as a reminder that previous
versions of the package should be marked as obsolete.
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11844Closes#11895
zfs_crypto_load_key() only works on encryption roots,
and zfs mount -la would fail if it encounters a datasets that
is sorted before their encroots.
To trigger:
truncate -s 40G /tmp/test
dd if=/dev/urandom of=/tmp/k bs=128 count=1 status=none
zpool create -O encryption=on -O keylocation=file:///tmp/k \
-O keyformat=passphrase test /tmp/test
zfs create -o mountpoint=/a test/a
zfs create -o mountpoint=/b test/b
zfs umount test
zfs unload-key test
zfs mount -la
The final mount errored out with:
Key load error: Keys must be loaded for
encryption root of 'test/a' (test).
Key load error: Keys must be loaded for
encryption root of 'test/b' (test).
And only /test was mounted
This technically breaks the libzfs API, but the previous behavior was
decidedly a bug.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11870Closes#11875
It happens to trip over an assert but does not matter for correctness at
this time. Done for future proofing.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#11884
zfs recv -n does not report some errors it could. The code to bail
out of the receive if in dry-run mode came a little early, skipping
validation of cmdprops (recv -x and -o) among others. Move the
check down to enable these additional checks.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: InsanePrawn <insane.prawny@gmail.com>
Closes#11862
Several improvements to the operation of the 'compatibility' property:
1) Improved handling of unrecognized features:
Change the way unrecognized features in compatibility files are handled.
* invalid features in files under /usr/share/zfs/compatibility.d
only get a warning (as these may refer to future features not yet in
the library),
* invalid features in files under /etc/zfs/compatibility.d
get an error (as these are presumed to refer to the current system).
2) Improved error reporting from zpool_load_compat.
Note: slight ABI change to zpool_load_compat for better error reporting.
3) compatibility=legacy inhibits all 'zpool upgrade' operations.
4) Detect when features are enabled outside current compatibility set
* zpool set compatibility=foo <-- print a warning
* zpool set feature@xxx=enabled <-- error
* zpool status <-- indicate this state
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Colm Buckley <colm@tuatha.org>
Closes#11861
It's been observed in the CI that the required 25% of obsolete bytes
in the mapping can be to high a threshold for this test resulting in
condensing never being triggered and a test failure. To prevent these
failures make the existing zfs_condense_indirect_obsolete_pct tuning
available so the obsolete percentage can be reduced from 25% to 5%
during this test.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11869
Commit 099fa7e4 intentionally modified the libzfs ABI. However, it
failed to include an update for the libzfs.abi file. This commit
resolves the `make checkabi` warning due to that omission.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11710
The fault/auto_spare_shared, l2arc/persist_l2arc_007_pos, and
alloc_class/alloc_class_013_pos test cases are not entirely reliable
and may occasionally fail resulting in a false positive in the CI.
Add these tests to known list of possible failures until they can
be made 100% reliable.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11890
As found by
git grep -E '(open|setmntent|pipe2?)\(' |
grep -vE '((zfs|zpool)_|fd|dl|lzc_re|pidfile_|g_)open\('
FreeBSD's pidfile_open() says nothing about the flags of the files it
opens, but we can't do anything about it anyway; the implementation does
open all files with O_CLOEXEC
Consider this output with zpool.d/media appended with
"pid=$$; (ls -l /proc/$pid/fd > /dev/tty)":
$ /sbin/zpool iostat -vc media
lrwx------ 0 -> /dev/pts/0
l-wx------ 1 -> 'pipe:[3278500]'
l-wx------ 2 -> /dev/null
lrwx------ 3 -> /dev/zfs
lr-x------ 4 -> /proc/31895/mounts
lrwx------ 5 -> /dev/zfs
lr-x------ 10 -> /usr/lib/zfs-linux/zpool.d/media
vs
$ ./zpool iostat -vc vendor,upath,iostat,media
lrwx------ 0 -> /dev/pts/0
l-wx------ 1 -> 'pipe:[3279887]'
l-wx------ 2 -> /dev/null
lr-x------ 10 -> /usr/lib/zfs-linux/zpool.d/media
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11866
These were fd 3, 4, and 5 by the time zfs change-key hit
execute_key_fob()
glibc appends "e" to setmntent() mode, but musl's just returns fopen()
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11866
This changes the password prompt for new encryption roots from
Enter passphrase:
Re-enter passphrase:
to
Enter new passphrase:
Re-enter new passphrase:
which makes more sense and is more consistent with "new passphrase"
now always meaning "come up with something" and plain "passphrase"
"remember that thing"
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11866
A tentative implementation and discussion was done in #5285.
According to it a send --skip-missing|-s flag has been added.
In a replication stream, when there are snapshots missing in
the hierarchy, if -s is provided print a warning and ignore
dataset (and its children) instead of throwing an error
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Pablo Correa Gómez <ablocorrea@hotmail.com>
Closes#11710
Without this Obsoletes, using packages built --with-spec=redhat, an
upgrade from zfs-0.7 to zfs-2.x does not cause the kmod-spl-0.7 package
to be removed.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#11865
list_zvols() would happily, for zvols with spaces in their names,
assign the second half to volmode, &c., so use a normal read
and set IFS to a tab instead of using 4 separate AWK processes(?)
Similarly, in filter_out_deleted_zvols(), run zfs(8) once and use the
output directly instead of spawning a zfs(8) process per zvol
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11859
SMACK needs to have the ZFS dentry security field setup before
SMACK's d_instantiate() hook is called as it requires functioning
'__vfs_getxattr()' calls to properly set the labels.
Fxes:
1) file instantiation properly setting the object label to the
subject's label
2) proper file labeling in a transmutable directory
Functions Updated:
1) zpl_create()
2) zpl_mknod()
3) zpl_mkdir()
4) zpl_symlink()
External-issue: https://github.com/cschaufler/smack-next/issues/1
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: TerraTech <TerraTech@users.noreply.github.com>
Closes#11646Closes#11839
Kill the removal operation on every platform, not just Linux.
The test has been fixed and is now stable on FreeBSD.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11856
Added a check for alien 8.95.{1,2,3}, which is known to fail to
generate debs 100% of the time, and instead print out a message
informing the developer that it's known to be broken and linking
them to more information.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#11848Closes#11850
When a rebuild completes it will automatically schedule a follow up
scrub to verify all of the block checksums. Before setting up the
scrub execute the counterpart dsl_scan_setup_check() function to
confirm the scrub can be started. Prior to this change we'd only
check vdev_rebuild_active() which isn't as comprehensive, and using
the check function keeps all of this logic in one place.
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11849
As described in #11854, zhack is occasionally segfaulting on FreeBSD.
Debugging this is proving to be tricky. To avoid false positives in
the CI add entries for the tests that use zhack in zts-report to
accept that they may occasionally fail on FreeBSD.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Issue #11854Closes#11855
Just as delay zevents can flood the zevent pipe when a vdev becomes
unresponsive, so do the deadman zevents.
Ratelimit deadman zevents according to the same tunable as for delay
zevents.
Enable deadman tests on FreeBSD and add a test for deadman event
ratelimiting.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Don Brady <don.brady@delphix.com>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11786
It's all of 40 bytes with 4-byte pointers and 64 with 8-byte ones
(previously 44 and 88, respectively) ‒
there's no reason it can't live on the stack
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11860
We set SA_RESTART early on, which will prevent EINTRs (indeed, to the
point of needing to clear it in the reaper, since it interferes with
pause(2)), which is the only error zed_file_write_n() actually handled
(plus, the pid write is no bigger than 12 bytes anyway)
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11834
These events should currently never be generated.
Also untag _zed_event_add_nvpair() from merge with
zpool_do_events_nvprint() ‒ they serve different purposes (machine,
usually script vs human consumption) and format the output differently
as it stands
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11834
And add a note on /why/ ZEDLETs need to be owned by root
Quoth chown(2), Linux man-pages project:
Only a privileged process (Linux: one with the CAP_CHOWN capability)
may change the owner of a file.
Quoth chown(2), FreeBSD:
[EPERM] The operation would change the ownership,
but the effective user ID is not the super-user.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11834
There simply isn't a need for one, since the flags the daemon takes
are all short (mostly just toggles) and administrative in nature,
and are therefore better served by the age-old tradition of sourcing an
environment file and preparing the cmdline in the init-specific handler
itself, if needed at all
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11834
/dev/fd on Darwin
Consider the following strace output:
prlimit64(0, RLIMIT_NOFILE, NULL, {rlim_cur=1024, rlim_max=1024*1024}) = 0
Yes, that is well over a million file descriptors!
This reduces the ZED start-up time from "at least a second" to
"instantaneous", and, under strace, from "don't even try" to "usable"
by simple virtue of doing five syscalls instead of over a million;
in most cases the main loop does nothing
Recent Linuxes (5.8+) have close_range(2) for this, but that's an
overoptimisation (and libcs don't have wrappers for it yet)
This is also run by the ZEDLET pre-exec. Compare:
Finished "all-syslog.sh" eid=13 pid=6717 time=1.027100s exit=0
Finished "history_event-zfs-list-cacher.sh" eid=13 pid=6718 time=1.046923s exit=0
to
Finished "all-syslog.sh" eid=12 pid=4834 time=0.001836s exit=0
Finished "history_event-zfs-list-cacher.sh" eid=12 pid=4835 time=0.001346s exit=0
lol
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11834
200ms time-out is relatively long, but if we already hit the cap,
then we'll likely be able to spawn multiple new jobs when we wake up
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11807
rpm/redhat/zfs-kmod.spec.in has a typo in the shell code that
creates the kmod-preamble file. This typo results in the
preamble file having the wrong name,
./SOURCES/kmod-preamblenObsoletes
and missing the Obsoletes clause that has become part of the name.
Because the filename is incorrect, the built package does not have
"obsoletes" or "conflicts" set.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#11851
In order for package managers such as dnf to upgrade cleanly after
the package SONAME bump the obsolete package names must be known.
Update the new packages to correctly obsolete the old ones.
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11844Closes#11847
This effectively reverts
4fc411f7a3 (part of #6807) and
f6fbe25664 (#9042) ‒
the code itself and latter PR cite symmetry with whole-disk-vdev
behaviour (presumably because rootfs vdevs are rarely whole disks),
but the code is broken for NVME devices (indeed, it'd strip the
controller number instead of the (potential) partition number, turning
"nvme0n1p1" into "nvmen1p1", which would then subsequently fail the
sysfs existence check); it could be fixed to handle those (and any
others) rather easily by dereferencing /sys/class/block/$devname,
but this isn't the place for setting this ‒ as noted in the commit that
removed setting the scheduler by default
(9e17e6f254) ‒ use an udev rule
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11838
IFS= would break loops in import_pool(), which would fault
any automatic import
Additionally $ZFS_BOOTFS from cmdline would interfere with find_rootfs()
If many pools were present, same thing could happen across multiple
find_rootfs() runs, so bail out early and clean up in error path
Suggested-by: @nachtgeist
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11278Closes#11838
get_clones_string currently returns an empty string for filesystem
snapshots which have no clones. This breaks parsable `zfs get` output as
only three columns are output, instead of 4.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Fiddaman <github@m.fiddaman.uk>
Co-authored-by: matt <matt@fiddaman.net>
Closes#11837
The exact limitations on what features are supported when booting
vary considerably depending on the environment. In order to minimize
confusion avoid categorical statements which assume GRUB2 is being
used. The supported GRUB2 features are covered earlier in this man
page for easy reference.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11842
zpool list, which is the only user, would mistakenly try to parse the
empty string as the interval in this case:
$ zpool list "a"
cannot open 'a': no such pool
$ zpool list ""
interval cannot be zero
usage: <usage string follows>
which is now symmetric with zpool get:
$ zpool list ""
cannot open '': name must begin with a letter
Avoid breaking the "interval cannot be zero" string.
There simply isn't a need for this, and it's user-facing.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11841Closes#11843
The pool_checkpoint tests may incorrectly fail because several of
them invoke zdb for an imported pool. In this scenario it's not
unexpected for zdb to fail if the pool is modified. To resolve
this these zdb checks are now done after the pool has been exported.
Additionally, the default cleanup functions assumed the pool would
be imported when they were run. If this was not the case they're
exit early and fail to cleanup all of the test state causing
subsequent tests to fail. Add a check to only destroy the pool
when it is imported.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11832
/dev/zfs is 0:0 666 on most systems, so the [ -w /dev/zfs ] check always
succeeds, but if zfs isn't in $PATH (e.g. when completing from
"/sbin/zfs list" on a regular account) this can lead to error spew like
nabijaczleweli@szarotka:~$ /sbin/zfs list bash: zfs: command not found
@ bash: zfs: command not found
We only do read-only commands, and quite general ones at that,
so there's no need to elevate one way or another.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11828
Document the project's policy regarding publishing and maintaining
official OpenZFS releases.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11821
Bump the library versions as advised by the libtool guidelines.
https://www.gnu.org/software/libtool/manual/html_node/Updating-version-info.html
Two new functions were added but no existing functions were changed,
so we increase the version and the age (version:revision:age).
Added functions (2):
- boolean_t zpool_is_draid_spare(const char *);
- zpool_compat_status_t zpool_load_compat(const char *,
boolean_t *, char *, char *);
Additionally bump the libzpool.so version information. This library
is for internal use but we still want to update the version to track
major changes to the interfaces.
The libzfsbootenv, libuutil, libnvpair and libzfs_core libraries
have not been updated.
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11817
Nothing bad happens if a prefix of your pool name matches a disk name.
This is a bit of a silly restriction at this point.
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#11781Closes#11813
The lower bound for this scaling to too low and the upper bound is too
high. Use a fixed default length of 512 instead, which is a reasonable
value on any system.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11822
ratelimit_dropped isn't protected by a lock and is expected to
be updated atomically.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11822
Recently we've been running out of free space in the ubuntu 20.04
environment resulting in test failures. This appears to be caused
by a change in the default available free space and not because of
any change in OpenZFS. Try and avoid this failure by applying a
suggested workaround which removes some unnecessary files.
https://github.com/actions/virtual-environments/issues/2840
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11826
The configure check for iops->rename wanting flags was missing the
AC_MSG_CHECKING() so it would just print yes without saying what was
being checked.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Brian Atkinson <batkinson@lanl.gov>
Closes#11825
Update the fsck.zfs helper to bubble up some already-known-about
errors if they are detected in the pool.
health=degraded => 4/"Filesystem errors left uncorrected"
health=faulted && dataset in /etc/fstab => 8/"Operational error"
pool not found => 8/"Operational error"
everything else => 0
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11806
ZoL 0.6.1 introduced feature flags with the three features that all
implementations at the time were guaranteed to have. 0.6.4 introduced
a few more until 0.6.5 added two after that. OpenZFS 2.1 added the
dRAID feature.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Mike Swanson <mikeonthecomputer@gmail.com>
Closes#11818
When a child process is killed waitpid() must be called on the
pid the reap the zombie process.
Update BUGS section to reflect reality by replacing "zedlets
aren't time limited with "zedlets can be interrupted".
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11769Closes#11798
For gang blocks, `DVA_GET_ASIZE()` is the total space allocated for the
gang DVA including its children BP's. The space allocated at each DVA's
vdev/offset is `vdev_psize_to_asize(vd, SPA_GANGBLOCKSIZE)`.
This commit makes this relationship more clear by using a helper
function, `vdev_gang_header_asize()`, for the space allocated at the
gang block's vdev/offset.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#11744
When specifying the name of a RAIDZ vdev on the command line, it can be
specified as raidz-<vdevID> or raidzP-<vdevID>.
e.g. `zpool clear poolname raidz-0` or `zpool clear poolname raidz2-0`
If the parity is specified in the vdev name, it should match the actual
parity of that RAIDZ vdev, otherwise the command should fail. This
commit makes it so.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Stuart Maybee <stuart.maybee@comcast.net>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#11742
Other (all?) Linux filesystems seem to return -EPERM instead of -EACCESS
when trying to set FS_APPEND_FL or FS_IMMUTABLE_FL without the
CAP_LINUX_IMMUTABLE capability. This was detected by generic/545 test
in the fstest suite.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Luis Henriques <henrix@camandro.org>
Closes#11791
Arm-based Macs are like FreeBSD and provide a full 64-bit stat from the
start, so have no stat64 variants. Thus, define stat64 and fstat64 as
aliases for the normal versions.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Jessica Clarke <jrtc27@jrtc27.com>
Closes#11771
To make better predictions on parallel workloads dmu_zfetch() should
be called as early as possible to reduce possible request reordering.
In particular, it should be called before dmu_buf_hold_array_by_dnode()
calls dbuf_hold(), which may sleep waiting for indirect blocks, waking
up multiple threads same time on completion, that can significantly
reorder the requests, making the stream look like random. But we
should not issue prefetch requests before the on-demand ones, since
they may get to the disks first despite the I/O scheduler, increasing
on-demand request latency.
This patch splits dmu_zfetch() into two functions: dmu_zfetch_prepare()
and dmu_zfetch_run(). The first can be executed as early as needed.
It only updates statistics and makes predictions without issuing any
I/Os. The I/O issuance is handled by dmu_zfetch_run(), which can be
called later when all on-demand I/Os are already issued. It even
tracks the activity of other concurrent threads, issuing the prefetch
only when _all_ on-demand requests are issued.
For many years it was a big problem for storage servers, handling
deeper request queues from their clients, having to either serialize
consequential reads to make ZFS prefetcher usable, or execute the
incoming requests as-is and get almost no prefetch from ZFS, relying
only on deep enough prefetch by the clients. Benefits of those ways
varied, but neither was perfect. With this patch deeper queue
sequential read benchmarks with CrystalDiskMark from Windows via
iSCSI to FreeBSD target show me much better throughput with almost
100% prefetcher hit rate, comparing to almost zero before.
While there, I also removed per-stream zs_lock as useless, completely
covered by parent zf_lock. Also I reused zs_blocks refcount to track
zf_stream linkage of the stream, since I believe previous zs_fetch ==
NULL check in dmu_zfetch_stream_done() was racy.
Delete prefetch streams when they reach ends of files. It saves up
to 1KB of RAM per file, plus reduces searches through the stream list.
Block data prefetch (speculation and indirect block prefetch is still
done since they are cheaper) if all dbufs of the stream are already
in DMU cache. First cache miss immediately fires all the prefetch
that would be done for the stream by that time. It saves some CPU
time if same files within DMU cache capacity are read over and over.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Adam Moss <c@yotes.com>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#11652
If TX_WRITE is create on a file, and the file is later deleted and a new
directory is created on the same object id, it is possible that when
zil_commit happens, zfs_get_data will be called on the new directory.
This may result in panic as it tries to do range lock.
This patch fixes this issue by record the generation number during
zfs_log_write, so zfs_get_data can check if the object is valid.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chunwei Chen <david.chen@nutanix.com>
Closes#10593Closes#11682
Commit 235a85657 introduced a regression in evaluation of POSIX modes
that require group DENY entries in the internal ZFS ACL. An example
of such a POSX mode is 007. When write_implies_delete_child is set,
then ACE_WRITE_DATA is added to `wanted_dirperms` in prior to calling
zfs_zaccess_common(). This occurs is zfs_zaccess_delete().
Unfortunately, when zfs_zaccess_aces_check hits this particular DENY
ACE, zfs_groupmember() is checked to determine whether access should be
denied, and since zfs_groupmember() always returns B_TRUE on Linux and
so this check is failed, resulting ultimately in EPERM being returned.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Andrew Walker <awalker@ixsystems.com>
Closes#11760
The FreeBSD boot loader relies on the bootfs property and is capable
of booting from removed (indirect) vdevs.
Reviewed-by Eric van Gyzen
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Martin Matuska <mm@FreeBSD.org>
Closes#11763
It used to be required to pass a enum km_type to kmap_atomic() and
kunmap_atomic(), however this is no longer necessary and the wrappers
zfs_k(un)map_atomic removed these. This is confusing in the ABD code as
the struct abd_iter member iter_km no longer exists and the wrapper
macros simply compile them out.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Adam Moss <c@yotes.com>
Signed-off-by: Brian Atkinson <batkinson@lanl.gov>
Closes#11768
= Motivation
We've noticed several zloop crashes within Delphix generated
due to the following sequence of events:
- A device gets expanded and new metaslabas are allocated for
it. These metaslabs go through `metaslab_init()` but haven't
gone through `metaslab_sync_done()` yet. This meas that the
only range tree that's actually set is the `ms_allocatable`.
All the others are NULL.
- A vdev_initialization is issues and `vdev_initialize_thread`
starts processing one of these new metaslabs of the expanded
vdev.
- As part of `vdev_initialize_calculate_progress()` we call
into `metaslab_load()` and `metaslab_load_impl()` which
in turn tries to dereference the metaslabs trees that
are still NULL and therefore we crash.
The same failure can come up from the `vdev_trim` code paths.
= This Patch
We considered the following solutions to deal with this issue:
[A] Add logic to `vdev_initialize/trim` to skip those new
metaslabs. We decided against this as it would be good
to avoid exposing this lower-level detail to higer-level
operations.
[B] Have `metaslab_load_impl()` return early for new metaslabs
and thus never touch those range_trees that are NULL at
that time. This seemed more of a work-around for the bug
and not a clear-cut solution.
[C] Refactor our logic so all metaslabs have their range_trees
created at the time of their creatin in `metaslab_init()`.
In this patch we decided to go with [C] because:
(1) It doesn't expose more metaslab details to higher level
operations such as vdev initialize and trim.
(2) The current behavior of creating the range trees lazily
in `metaslab_sync_done()` is unnecessarily complicated.
(3) Always initializing the metaslab range_trees makes other
parts of the codebase cleaner. For example, we used to
use `ms_freed` as the reference value for knowing whether
all the range_trees have been initialized. Now we no
longer need to do that check in most places (and in the
few that we do we use the `ms_new` boolean field now
which is more readable).
= Side Changes
Probably due to a mismerge we set `ms_loaded` to `B_TRUE` twice
in `metasloab_load_impl()`. In this patch we remove the extraneous
assignment.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Closes#11737
The BIO_MAX_PAGES macro is being retired in favor of a bio_max_segs()
function that implements the typical MIN(x,y) logic used throughout the
kernel for bounding the allocation, and also the new implementation is
intended to be signed-safe (which the former was not).
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#11765
In Linux 5.12, the filesystem API was modified to support ipmapped
mounts by adding a "struct user_namespace *" parameter to a number
functions and VFS handlers. This change adds the needed autoconf
macros to detect the new interfaces and updates the code appropriately.
This change does not add support for idmapped mounts, instead it
preserves the existing behavior by passing the initial user namespace
where needed. A subsequent commit will be required to add support
for idmapped mounted.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#11712
The RAIDZ and DRAID code is responsible for reporting checksum errors on
their child vdevs. Checksum errors represent events where a disk
returned data or parity that should have been correct, but was not. In
other words, these are instances of silent data corruption. The
checksum errors show up in the vdev stats (and thus `zpool status`'s
CKSUM column), and in the event log (`zpool events`).
Note, this is in contrast with the more common "noisy" errors where a
disk goes offline, in which case ZFS knows that the disk is bad and
doesn't try to read it, or the device returns an error on the requested
read or write operation.
RAIDZ/DRAID generate checksum errors via three code paths:
1. When RAIDZ/DRAID reconstructs a damaged block, checksum errors are
reported on any children whose data was not used during the
reconstruction. This is handled in `raidz_reconstruct()`. This is the
most common type of RAIDZ/DRAID checksum error.
2. When RAIDZ/DRAID is not able to reconstruct a damaged block, that
means that the data has been lost. The zio fails and an error is
returned to the consumer (e.g. the read(2) system call). This would
happen if, for example, three different disks in a RAIDZ2 group are
silently damaged. Since the damage is silent, it isn't possible to know
which three disks are damaged, so a checksum error is reported against
every child that returned data or parity for this read. (For DRAID,
typically only one "group" of children is involved in each io.) This
case is handled in `vdev_raidz_cksum_finish()`. This is the next most
common type of RAIDZ/DRAID checksum error.
3. If RAIDZ/DRAID is not able to reconstruct a damaged block (like in
case 2), but there happens to be additional copies of this block due to
"ditto blocks" (i.e. multiple DVA's in this blkptr_t), and one of those
copies is good, then RAIDZ/DRAID compares each sector of the data or
parity that it retrieved with the good data from the other DVA, and if
they differ then it reports a checksum error on this child. This
differs from case 2 in that the checksum error is reported on only the
subset of children that actually have bad data or parity. This case
happens very rarely, since normally only metadata has ditto blocks. If
the silent damage is extensive, there will be many instances of case 2,
and the pool will likely be unrecoverable.
The code for handling case 3 is considerably more complicated than the
other cases, for two reasons:
1. It needs to run after the main raidz read logic has completed. The
data RAIDZ read needs to be preserved until after the alternate DVA has
been read, which necessitates refcounts and callbacks managed by the
non-raidz-specific zio layer.
2. It's nontrivial to map the sections of data read by RAIDZ to the
correct data. For example, the correct data does not include the parity
information, so the parity must be recalculated based on the correct
data, and then compared to the parity that was read from the RAIDZ
children.
Due to the complexity of case 3, the rareness of hitting it, and the
minimal benefit it provides above case 2, this commit removes the code
for case 3. These types of errors will now be handled the same as case
2, i.e. the checksum error will be reported against all children that
returned data or parity.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#11735
The `rr_code` field in `raidz_row_t` is unused.
This commit removes the field, as well as the code that's used to set
it.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#11736
Don't handle (incorrectly) kmem_zalloc() failure. With KM_SLEEP,
will never return NULL.
Free the data allocated for non-virtual kstats when deleting the object.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11767
zhold() wraps igrab() on Linux, and igrab() may fail when the inode
is in the process of being deleted. This means zhold() must only be
called when a reference exists and therefore it cannot be deleted.
This is the case for all existing consumers so add a VERIFY and a
comment explaining this requirement.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Adam Moss <c@yotes.com>
Closes#11704
The man page was missing these two permissions.
Add the missing permissions to the man page.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jeremy Faulkner <gldisater@gldis.ca>
Closes#11727
Create a new section of tests to run with acltype=off.
For now the only test we have is for the DOS mode READONLY attribute on
FreeBSD.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11734
To make use of zfs_refcount_held tunable it should be a module
parameter in open-zfs. Also, since the macros will auto-generate OS
specific tunables, removed the existing zfs_refcount_held reference
in module/os/freebsd/zfs/sysctl_os.c.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Don Brady <don.brady@delphix.com>
Closes#11753
You can't use user_run to eval ksh functions defined in libtest unless
you include libtest in the user shell.
Fix xattr_003_neg by:
* include libtest in the user shell
* *then* run get_xattr
* assert this fails
* use variables for filenames so they don't change in the user's shell
* don't log the contents of /etc/passwd
* cleanup all byproducts
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11185
The current user_run often does not work as expected. Commands are run
in a different shell, with a different environment, and all output is
discarded.
Simplify user_run to retain the current environment, eliminate eval,
and feed the command string into ksh. Enhance the logging for
user_run so we can see out and err.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11185
Add parsing of the rewind options.
When I was upstreaming the change [1], I omitted the part where we
detect that the pool should be rewind. When the FreeBSD repo has
synced with the OpenZFS, this part of the code was removed.
[1] FreeBSD repo: 277f38abffc6a8160b5044128b5b2c620fbb970c
[2] OpenZFS repo: f2c027bd6a
External-issue: https://bugs.freebsd.org/bugzilla/show_bug.cgi?id=254152
Originally reviewed by: tsoome, allanjude
Originally reviewed by: kevans (ok from high-level overview)
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Mariusz Zaborski <oshogbo@vexillium.org>
Closes#11730
Resolve some oddities in zfsdev_close() which could result in a
panic and were not present in the equivalent function for Linux.
- Remove unused definition ZFS_MIN_MINOR
- FreeBSD: Simplify zfsdev state destruction
- Assert zs_minor is valid in zfsdev_close
- Make locking around zfsdev state match Linux
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11720
This deserializes otherwise non-contending operations.
The previous scheme of using 17 locks hashed by curthread runs into
conflicts very quickly. Check the pull request for sample results.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#11153
This will allow platforms to implement it as they see fit, in particular
in a different manner than rrm locks.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#11153
Importing a pool using the cachefile is ideal to reduce the time
required to import a pool. However, if the devices associated with
a pool in the cachefile have changed, then the import would fail.
This can easily be corrected by doing a normal import which would
then read the pool configuration from the labels.
The goal of this change is make importing using a cachefile more
resilient and auto-correcting. This is accomplished by having
the cachefile import logic automatically fallback to reading the
labels of the devices similar to a normal import. The main difference
between the fallback logic and a normal import is that the cachefile
import logic will only look at the device directories that were
originally used when the cachefile was populated. Additionally,
the fallback logic will always import by guid to ensure that only
the pools in the cachefile would be imported.
External-issue: DLPX-71980
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Wilson <gwilson@delphix.com>
Closes#11716
A few deadman tunables ended up in the wrong sysctl node.
Move them to vfs.zfs.deadman.*
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11715
Add branch hints and constify the intermediate evaluations of
left/right params in VERIFY3*().
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Adam Moss <c@yotes.com>
Closes#11708
Some .h files that were added were missed in this Makefile. Since
they are .h files, their being missing only resulted in them
disappeared from the dist archive.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Closes#11705
Our checkstyle doesn't work well on Ubuntu 20.04,
temporary pin it to 18.04.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Melikov <mail@gmelikov.ru>
Closes#11713
Added errno mappings to unmount_one() in libzfs. Changed do_unmount()
implementation to return errno errors directly like is done for
do_mount() and others.
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@delphix.com>
Closes#11681
vdev_id uses the /dev/mapper/ symlinks to resolve a UUID to a dm name
(like dm-1). However on some multipath setups, there is no /dev/mapper/
entry for the UUID at the time vdev_id is called by udev. However,
this isn't necessarily needed, as we may be able to resolve the dm
name from the $DEVNAME that udev passes us (like DEVNAME="/dev/dm-1").
This patch tries to resolve the dm name from $DEVNAME first, before
falling back to looking in /dev/mapper/. This fixed an issue where the
by-vdev names weren't reliably showing up on one of our nodes.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#11698
events_002 exercises the ZED, ensuring that it neither misses events,
nor reporting events twice.
On slow test hardware, some of the timeouts are insufficient to allow
the ZED to properly settle. Conversely, on fast hardware these same
timeouts are too long, unnecessarily slowing the test run.
Instead of using a fixed timeout, wait for the expected final event
before returning. Additionally, wait with a timeout for unexpected
events to avoid missing them if they show up late.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Antonio Russo <aerusso@aerusso.net>
Closes#11703
zil_replaying(zil, tx) has the side-effect of informing the ZIL that an
entry has been replayed in the (still open) tx. The ZIL uses that
information to record the replay progress in the ZIL header when that
tx's txg syncs.
ZPL log entries are not idempotent and logically dependent and thus
calling zil_replaying() is necessary for correctness.
For ZVOLs the question of correctness is more nuanced: ZVOL logs only
TX_WRITE and TX_TRUNCATE, both of which are idempotent. Logical
dependencies between two records exist only if the write or discard
request had sync semantics or if the ranges affected by the records
overlap.
Thus, at a first glance, it would be correct to restart replay from
the beginning if we crash before replay completes. But this does not
address the following scenario:
Assume one log record per LWB.
The chain on disk is
HDR -> 1:W(1, "A") -> 2:W(1, "B") -> 3:W(2, "X") -> 4:W(3, "Z")
where N:W(O, C) represents log entry number N which is a TX_WRITE of C
to offset A.
We replay 1, 2 and 3 in one txg, sync that txg, then crash.
Bit flips corrupt 2, 3, and 4.
We come up again and restart replay from the beginning because
we did not call zil_replaying() during replay.
We replay 1 again, then interpret 2's invalid checksum as the end
of the ZIL chain and call replay done.
The replayed zvol content is "AX".
If we had called zil_replaying() the HDR would have pointed to 3
and our resumed replay would not have replayed anything because
3 was corrupted, resulting in zvol content "BX".
If 3 logically depends on 2 then the replay corrupted the ZVOL_OBJ's
contents.
This patch adds the zil_replaying() calls to the replay functions.
Since the callbacks in the replay function need the zilog_t* pointer
so that they can call zil_replaying() we open the ZIL while
replaying in zvol_create_minor(). We also verify that replay has
been done when on-demand-opening the ZIL on the first modifying
bio.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Christian Schwarz <me@cschwarz.com>
Closes#11667
* Restore original kern.corefile value after the test.
* Don't leave behind a frozen pool.
* Clean up leftover vdev files.
* Make zpool_002_pos and zpool_003_pos consistent in their handling of
core files while here.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11694
Docs for send and receive do not explain behavior when sending a
compressed stream then receiving on a host that overrides compression
with -o compress=value.
The data from the send stream is written as it was from the send is
the compressed form but the compression algorithm set on the receiver
is the overridden version which causes some confusion as to what
algorithm was actually used.
Updated man docs to clarify behavior
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed By: Allan Jude <allanjude@freebsd.org>
Signed-off-by: manfromafar <manfromafar@outlook.com>
Closes#11690
ZFS_READONLY represents the "DOS R/O" attribute.
When that flag is set, we should behave as if write access
were not granted by anything in the ACL. In particular:
We _must_ allow writes after opening the file r/w, then
setting the DOS R/O attribute, and writing some more.
(Similar to how you can write after fchmod(fd, 0444).)
Restore these semantics which were lost on FreeBSD when refactoring
zfs_write. To my knowledge Linux does not actually expose this flag,
but we'll need it to eventually so I've added the supporting checks.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11693
For some reason cppcheck 1.90 is generating an invalidSyntax warning
when the BF64_SET macro is used in the zstream source. The same
warning is not reported by cppcheck 2.3, nor is their any evident
problem with the expanded macro. This appears to be an issue with
this version of cppcheck. This commit annotates the source to suppress
the warning.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11700
When populating a ZIL destination buffer ensure it is always
zeroed before its contents are constructed.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Tom Caputi <caputit1@tcnj.edu>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11687
Even when supplied with an abd to abd_get_offset_struct(), the call
to abd_get_offset_impl() can allocate a different abd. Ensure to
call abd_fini_struct() on the abd that is not used.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Closes#11683
Wire up the --enable-debug flag for configure to the FreeBSD module
build. Add --enable-invariants.
The running FreeBSD kernel config is used to detect whether to enable
INVARIANTS if not explicitly specified with --enable-invariants or
--disable-invariants.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11678
Bring the output of the removal status in line with the other
"fields" that zpool status outputs, and thus allows an parser to
easier detect this as continuation of the 'remove:' output.
Before:
remove: Removal of vdev 0 copied 282G in 0h9m, completed on [...]
776K memory used for removed device mappings
Now:
remove: Removal of vdev 0 copied 282G in 0h9m, completed on [...]
776K memory used for removed device mappings
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
Closes#11674
The spl_kmem_alloc showed up in some flamegraphs in a single-threaded
4k sync write workload at 85k IOPS on an
Intel(R) Xeon(R) Silver 4215 CPU @ 2.50GHz.
Certainly not a huge win but I believe the change is clean and
easy to maintain down the road.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Christian Schwarz <me@cschwarz.com>
Closes#11666
When a device which is actively trimming or initializing becomes
FAULTED, and therefore no longer writable, cancel the active
TRIM or initialization. When the device is merely taken offline
with `zpool offline` then stop the operation but do not cancel it.
When the device is brought back online the operation will be
resumed if possible.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Vipin Kumar Verma <vipin.verma@hpe.com>
Signed-off-by: Srikanth N S <srikanth.nagasubbaraoseetharaman@hpe.com>
Closes#11588
The function has three similar pieces of code: for read-behind pages,
requested pages and read-ahead pages. All three pieces had an
assert to ensure that the page is not mapped. Later the assert was
relaxed to require that the page is not mapped for writing. But that
was done in two places out of three. This change fixes the third piece,
read-ahead.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andriy Gapon <avg@FreeBSD.org>
Closes#11654
Several of the TRIM tests were based of the initialize tests and
then adapted for TRIM. The zpool_trim_start_and_cancel_pos.ksh
test was intended to be one such test but it was overlooked and
actually never adapted. Update it accordingly.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11649
After 35ec517 it has become possible to import ZFS pools witn an
active org.illumos:edonr feature on FreeBSD, leading to a panic.
In addition, "zpool status" reported all pools without edonr
as upgradable and "zpool upgrade -v" reported edonr in the list
of upgradable features.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Martin Matuska <mm@FreeBSD.org>
Closes#11653
The bio_*_acct functions became GPL exports, which causes the
kernel modules to refuse to compile. This replaces code with
alternate function calls to the disk_*_io_acct interfaces, which
are not GPL exports. This change was added in kernel commit
99dfc43ecbf67f12a06512918aaba61d55863efc.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#11639
The struct bio member bi_disk was moved underneath a new member named
bi_bdev. So all attempts to reference bio->bi_disk need to now become
bio->bi_bdev->bd_disk.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#11639
The metaslab_disable() call may block waiting for a txg sync.
Therefore it's important that vdev_rebuild_thread release the
SCL_CONFIG read lock it is holding before this call. Failure
to do so can result in the txg_sync thread getting blocked
waiting for this lock which results in a deadlock.
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewd-by: Srikanth N S <srikanth.nagasubbaraoseetharaman@hpe.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11647
Calling vdev_free() only requires the we acquire the spa config
SCL_STATE_ALL locks, not the SCL_ALL locks. In particular, we need
need to avoid taking the SCL_CONFIG lock (included in SCL_ALL) as a
writer since this can lead to a deadlock. The txg_sync_thread() may
block in spa_txg_history_init_io() when taking the SCL_CONFIG lock
as a reading when it detects there's a pending writer.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11585
Given a DM device name, the old vdev_id script would extract any text
after a 'p' as the partition number. It then appends "-part" + the
partition number to the name, giving a by-vdev name like "L0-part5".
This works fine if the DM name is like 'dm-2p5', but doesn't work if
the DM name is a multipath name like "mpatha". In those cases it
incorrectly matches the 'p' in "mpatha", giving by-vdev names like
"L0-partatha".
This patch fixes the issue by making the partition regex match stricter.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#11637
On Linux increase the maximum allowed size of the src nvlist which
can be passed to the /dev/zfs ioctl. Originally, this was set
to a maximum of KMALLOC_MAX_SIZE (4M) because it was kmalloc'd.
Since that time it's been converted to a vmalloc so that's no
longer a hard limit, and it's desirable for `zfs send/recv` to
allow larger nvlists so more snapshots can be sent at once.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6572Closes#11638
This change modifies the behavior of how we determine how much slop
space to use in the pool, such that now it has an upper limit. The
default upper limit is 128G, but is configurable via a tunable.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Prakash Surya <prakash.surya@delphix.com>
Closes#11023
gmake install fails when zpool.d compat links already exist.
Force the symlinks to be recreated if already present.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11633
The behavior of a NULL fromsnap was inadvertently changed for a doall
send when the send/recv logic in libzfs was updated. Restore the
previous behavior by correcting send_iterate_snap() to include all
the snapshots in the nvlist for this case.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Cedric Maunoury <cedric.maunoury@gmail.com>
Closes#11608
Using zfs-sh -u on linux will fail with inaccurate message when the
zfs modules are already unloaded. Deal with the case where a module
is already unloaded; its USE_COUNT will be the empty string
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Adam Moss <c@yotes.com>
Closes#11627
This prevents a panic after a SLOG add/removal on the root pool followed
by a zpool scrub.
When a SLOG is removed, a hole takes its place - the vdev_ops for a hole
is vdev_hole_ops, which defines the handler functions of vdev_op_hold
and vdev_op_rele as NULL.
This bug has been reported in illumos and FreeBSD, a different trigger
in the FreeBSD report though.
Credit for this patch goes to Patrick Mooney <pmooney@pfmooney.com>
Obtained from: illumos-gate commit: c65bd18728f34725
External-issue: https://www.illumos.org/issues/12981
External-issue: https://bugs.freebsd.org/bugzilla/show_bug.cgi?id=252396
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Wing <rob.fx907@gmail.com>
Closes#11623
A multpathed disk will have several 'underlying' paths to the disk. For
example, multipath disk 'dm-0' may be made up of paths:
/dev/{sda,sdb,sdc,sdd}. On many enclosures those underlying sysfs
paths will have a symlink back to their enclosure device entry
(like 'enclosure_device0/slot1'). This is used by the
statechange-led.sh script to set/clear the fault LED for a disk, and
by 'zpool status -c'.
However, on some enclosures, those underlying paths may not all have
symlinks back to the enclosure device. Maybe only two out of four
of them might.
This patch updates zfs_get_enclosure_sysfs_path() to favor returning
paths that have symlinks back to their enclosure devices, rather
than just returning the first path.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#11617
Making uio_impl.h the common header interface between Linux and FreeBSD
so both OS's can share a common header file. This also helps reduce code
duplication for zfs_uio_t for each OS.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Brian Atkinson <batkinson@lanl.gov>
Closes#11622
I think this is the behavior that most users expect.
Future work: have a separate flag, e.g., -O, to specify separate
set_global_vars for the zdb child than for the ztest children.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Signed-off-by: Christian Schwarz <me@cschwarz.com>
Closes#11602
Without set_global_var() in the child processes the -o option provides
little use.
Before this change set_global_var() was called as a side-effect of
getopt processing which only happens for the parent ztest process.
This change limits the set of options that can be set and makes them
available to the child through ztest_shared_opts_t.
Future work: support arbitrary option count and length.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Signed-off-by: Christian Schwarz <me@cschwarz.com>
Closes#11602
Without this patch I get the error
Setting global variables is only supported on little-endian systems
when using `zdb -o` on my amd64 machine.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Signed-off-by: Christian Schwarz <me@cschwarz.com>
Closes#11602
First, the crypto request completion handler contains a bug in that it
fails to reset fs_done correctly after the request is completed. This
is only a problem for asynchronous drivers. Second, some hardware
drivers have input constraints which ZFS does not satisfy. For
instance, ccp(4) apparently requires the AAD length for AES-GCM to be a
multiple of the cipher block size, and with qat(4) the AES-GCM AAD
length may not be longer than 240 bytes. FreeBSD's generic crypto
framework doesn't have a mechanism to automatically fall back to a
software implementation if a hardware driver cannot process a request,
and ZFS does not tolerate such errors.
The plan is to implement such a fallback mechanism, but with FreeBSD
13.0 approaching we should simply disable the use hardware drivers for
now.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#11612
That happens because of an off-by-one mistake.
share_mount_one_cb() calls report_mount_progress(current=sm_done) after
having incremented sm_done by one. Then report_mount_progress()
increments the parameter again. It appears that that logic became
obsolete after commit a10d50f999, parallel zfs mount.
On FreeBSD I observe that zfs mount -a -v prints, for example,
(null): (201/248)
That happens because set_progress_header() is never called.
With this change the output becomes correct:
Mounting ZFS filesystems: (209/248)
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andriy Gapon <avg@FreeBSD.org>
Closes#11607
Property to allow sets of features to be specified; for compatibility
with specific versions / releases / external systems. Influences
the behavior of 'zpool upgrade' and 'zpool create'. Initial man
page changes and test cases included.
Brief synopsis:
zpool create -o compatibility=off|legacy|file[,file...] pool vdev...
compatibility = off : disable compatibility mode (enable all features)
compatibility = legacy : request that no features be enabled
compatibility = file[,file...] : read features from specified files.
Only features present in *all* files will be enabled on the
resulting pool. Filenames may be absolute, or relative to
/etc/zfs/compatibility.d or /usr/share/zfs/compatibility.d (/etc
checked first).
Only affects zpool create, zpool upgrade and zpool status.
ABI changes in libzfs:
* New function "zpool_load_compat" to load and parse compat sets.
* Add "zpool_compat_status_t" typedef for compatibility parse status.
* Add ZPOOL_PROP_COMPATIBILITY to the pool properties enum
* Add ZPOOL_STATUS_COMPATIBILITY_ERR to the pool status enum
An initial set of base compatibility sets are included in
cmd/zpool/compatibility.d, and the Makefile for cmd/zpool is
modified to install these in $pkgdatadir/compatibility.d and to
create symbolic links to a reasonable set of aliases.
Reviewed-by: ericloewe
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Colm Buckley <colm@tuatha.org>
Closes#11468
Rather than conditionally compiling out the edonr code for FreeBSD
update zfs_mod_supported_feature() to indicate this feature is
unsupported. This ensures that all spa features are defined on
every platform, even if they are not supported.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11605
Issue #11468
There are two issues that don't allow ZFS to be compiled using uClibc.
`backtrace()`, and `program_invocation_short_name` as a `const`.
This patch adds uClibc to the conditionals in the same way there are
already for Glibc for `backtrace()`; and removes the external param
`program_invocation_short_name` because its only used here for the
whole project.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: José Luis Salvador Rufo <salvador.joseluis@gmail.com>
Closes#11600
FreeBSD's zfsd fails to build after e2af2acce3 due to strict type
checking errors from the implicit conversion between bool and boolean_t
in the inline predicate definitions in abd.h.
Use conditionals to return the correct value type from these functions.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#11592
Increase the Linux-Maximum version in the META file to 5.11.
All of the required compatibility patches have been merged.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11586
Within function sas_handler() userspace commands like
'/usr/sbin/multipath' have been replaced with sourcing
device details from within sysfs which reduced a
significant amount of overhead and processing time.
Multiple JBOD enclosures and their order are sourced
from the bsg driver (/sys/class/enclosure) to isolate
chassis top-level expanders, which are then dynamically
indexed based on host channel of the multipath subordinate
disk member device being processed. Additionally added a
"mixed" mode for slot identification for environments where
a ZFS server system may contain SAS disk slots where there
is no expander (direct connect to HBA) while an attached
external JBOD with an expander have different slot identifier
methods.
How Has This Been Tested?
~~~~~~~~~~~~~~~~~~~~~~~~~
Testing was performed on a AMD EPYC based dual-server
high-availability multipath environment with multiple
HBAs per ZFS server and four SAS JBODs. The two primary
JBODs were multipath/cross-connected between the two
ZFS-HA servers. The secondary JBODs were daisy-chained
off of the primary JBODs using aligned SAS expander
channels (JBOD-0 expanderA--->JBOD-1 expanderA,
JBOD-0 expanderB--->JBOD-1 expanderB, etc).
Pools were created, exported and re-imported, imported
globally with 'zpool import -a -d /dev/disk/by-vdev'.
Low level udev debug outputs were traced to isolate
and resolve errors.
Result:
~~~~~~~
Initial testing of a previous version of this change
showed how reliance on userspace utilities like
'/usr/sbin/multipath' and '/usr/bin/lsscsi' were
exacerbated by increasing numbers of disks and JBODs.
With four 60-disk SAS JBODs and 240 disks the time to
process a udevadm trigger was 3 minutes 30 seconds
during which nearly all CPU cores were above 80%
utilization. By switching reliance on userspace
utilities to sysfs in this version, the udevadm
trigger processing time was reduced to 12.2 seconds
and negligible CPU load.
This patch also fixes few shellcheck complains.
Reviewed-by: Gabriel A. Devenyi <gdevenyi@gmail.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Jeff Johnson <jeff.johnson@aeoncomputing.com>
Signed-off-by: Jeff Johnson <jeff.johnson@aeoncomputing.com>
Signed-off-by: Arshad Hussain <arshad.hussain@aeoncomputing.com>
Closes#11526
zfs_znode_update_vfs is a more platform-agnostic name than
zfs_inode_update. Besides that, the function's prototype is moved to
include/sys/zfs_znode.h as the function is also used in common code.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ka Ho Ng <khng300@gmail.com>
Sponsored by: The FreeBSD Foundation
Closes#11580
The first time through the loop prevdb and prevhdl are NULL. They
are then both set, but only prevdb is checked. Add an ASSERT to
make it clear that prevhdl must be set when prevdb is.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Kleber <klebertarcisio@yahoo.com.br>
Closes#10754Closes#11575
3d40b65 refactored zfs_vnops.c, which shared much code verbatim between
Linux and BSD. After a successful write, the suid/sgid bits are reset,
and the mode to be written is stored in newmode. On Linux, this was
propagated to both the in-memory inode and znode, which is then updated
with sa_update.
3d40b65 accidentally removed the initialization of newmode, which
happened to occur on the same line as the inode update (which has been
moved out of the function).
The uninitialized newmode can be saved to disk, leading to a crash on
stat() of that file, in addition to a merely incorrect file mode.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Antonio Russo <aerusso@aerusso.net>
Closes#11474Closes#11576
When all pools are exported ZFS will generate an empty cache file.
This will cause the import service to fail, which is sub-optimal,
since this means that dracut fails, and it necessary to run
`zpool import -a` to boot, delete the file, and regenerate+reinstall
the initrd.
This resolves the issue by treating an zero-length cache files the
same as a missing cache file. This aligns the behavior with that
of the `zpool` command itself.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11568
The pool guid and vdev guid received by zfs_agent_post_event(),
which calls zfs_retire_recv(), are normally non-zero. However,
later in this same method they may be unconditionally reset to
zero by the code which is intended to handle multipath, spare
and l2arc vdevs. This will result in the EC_dev_remove not
being handled.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>\
Co-authored-by: Vipin Kumar Verma <vipin.verma@hpe.com>
Signed-off-by: Srikanth N S <srikanth.nagasubbaraoseetharaman@hpe.com>
Closes#11564
Clarify how to include snapshots in the `zpool list` output by
referencing the full name of the `listsnapshots` pool property,
and the `zpool list -t snapshot` option.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11562Closes#11565
Expand the comments to make it clear exactly what is guaranteed
by dmu_tx_assign() and txg_hold_open(). Additionally, update
the comment which refers to txg_exit() when it should reference
txg_rele_to_sync().
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Christian Schwarz <me@cschwarz.com>
Closes#11521
This compatibility code is no longer needed. For it a while
iov_iter_init_compat() was used by zfs_uio_prefaultpages() but
this code should have been dropped as part of commit 83b91ae1.
Take care of that oversight and remove it.
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11543
ABD's currently track their parent/child relationship. This applies to
`abd_get_offset()` and `abd_borrow_buf()`. However, nothing depends on
knowing this relationship, it's only used for consistency checks to
verify that we are not destroying an ABD that's still in use. When we
are creating/destroying ABD's frequently, the performance impact of
maintaining these data structures (in particular the atomic
increment/decrement operations) can be measurable.
This commit removes this verification code on production builds, but
keeps it when ZFS_DEBUG is set.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#11535
In ZED zfs_retire agent added a check to handle Distributed Spare
replacement for Faulted VDEV also.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Vipin Kumar Verma <vipin.verma@hpe.com>
Signed-off-by: Mark Maybee <mark.maybee@hpe.com>
Closes#11354Closes#11355
I originally applied a fix in #11539 to fix a parent's child references
when a gang ABD is free'd. However, I did not take into account
abd_gang_add_gang(). We still need to make sure to update the child
references in this function as well. In order to resolve this I removed
decreasing the gang ABD's size in abd_free_gang() as well as moved back
the original placeent of zfs_refcount_remove_many() in abd_free().
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Brian Atkinson <batkinson@lanl.gov>
Closes#11542
`__vdev_disk_physio()` uses `abd_nr_pages_off()` to allocate a bio with
a sufficient number of iovec's to process this zio (i.e.
`nr_iovecs`/`bi_max_vecs`). If there are not enough iovec's in the bio,
then additional bio's will be allocated. However, this is a sub-optimal
code path. In particular, it requires several abd calls (to
`abd_nr_pages_off()` and `abd_bio_map_off()`) which will have to walk
the constituents of the ABD (the pages or the gang children) because
they are looking for offsets > 0.
For gang ABD's, `abd_nr_pages_off()` returns the number of iovec's
needed for the first constituent, rather than the sum of all
constituents (within the requested range). This always under-estimates
the required number of iovec's, which causes us to always need several
bio's. The end result is that `__vdev_disk_physio()` is usually O(n^2)
for gang ABD's (and occasionally O(n^3), when more than 16 bio's are
needed).
This commit fixes `abd_nr_pages_off()`'s handling of gang ABD's, to
correctly determine how many iovec's are needed, by adding up the number
of iovec's for each of the gang children in the requested range.
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#11536
If we do not write any buffers to the cache device and the evict hand
has not advanced do not update the cache device header.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#11522Closes#11537
Moving the call to zfs_refcount_remove_many() in abd_free() to be called
before any of the ABD free variants are called. This is necessary
because abd_free_gang() adjusts the abd_size for the gang ABD. If the
parent's child references are removed after free'ing the gang ABD the
refcount is not adjusted correctly for the parent's children.
I also removed some stray abd_put() in comments and changed
abd_free_gang_abd() -> abd_free_gang().
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Brian Atkinson <batkinson@lanl.gov>
Closes#11539
While you can use zdb -R poolname vdev:offset:[<lsize>/]<psize>[:flags]
to extract individual DVAs from a vdev, it would be handy for be able
copy an entire file out of the pool.
Given a file or object number, add support to copy the contents to a
file. Useful for debugging and recovery.
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Closes#11027
Before a hash table was added on top of the nvlist code, there were
cases where the nvlist allocation was changed from fnvlist_alloc()
to nvlist_alloc() to avoid expensive NV_UNIQUE_NAME checks. Now
this is no longer necessary. These changes should be reverted to be
consistent with other code. There are some cases where this change
will also reduce the number of iterations.
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Mark Maybee <mark.maybee@delphix.com>
Closes#11464
There is a race condition in zfs_zrele_async when we are checking if
we would be the one to evict an inode. This can lead to a txg sync
deadlock.
Instead of calling into iput directly, we attempt to perform the atomic
decrement ourselves, unless that would set the i_count value to zero.
In that case, we dispatch a call to iput to run later, to prevent a
deadlock from occurring.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#11527Closes#11530
If there is no scsi_debug module, then this test
must be skipped, in this case cleanup routine should
be prepared for absent pool.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Melikov <mail@gmelikov.ru>
Closes#11534
The runtime of vdev_validate is dominated by the disk accesses in
vdev_label_read_config. Speed it up by validating all vdevs in
parallel using a taskq.
Sponsored by: Axcient
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alan Somers <asomers@gmail.com>
Closes#11470
This is similar to what we already do in vdev_geom_read_config.
Sponsored by: Axcient
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alan Somers <asomers@gmail.com>
Closes#11470
metaslab_init is the slowest part of importing a mature pool, and it
must be repeated hundreds of times for each top-level vdev. But its
speed is dominated by a few serialized disk accesses. That can lead to
import times of > 1 hour for pools with many top-level vdevs on spinny
disks.
Speed up the import by using a taskqueue to parallelize vdev_load across
all top-level vdevs.
This also requires adding mutex protection to
metaslab_class_t.mc_historgram. The mc_histogram fields were
unprotected when that code was first written in "Illumos 4976-4984 -
metaslab improvements" (OpenZFS
f3a7f6610f). The lock wasn't added until
3dfb57a35e, though it's unclear exactly
which fields it's supposed to protect. In any case, it wasn't until
vdev_load was parallelized that any code attempted concurrent access to
those fields.
Sponsored by: Axcient
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alan Somers <asomers@gmail.com>
Closes#11470
In order for cppcheck to perform a proper analysis it needs to be
aware of how the sources are compiled (source files, include
paths/files, extra defines, etc). All the needed information is
available from the Makefiles and can be leveraged with a generic
cppcheck Makefile target. So let's add one.
Additional minor changes:
* Removing the cppcheck-suppressions.txt file. With cppcheck 2.3
and these changes it appears to no longer be needed. Some inline
suppressions were also removed since they appear not to be
needed. We can add them back if it turns out they're needed
for older versions of cppcheck.
* Added the ax_count_cpus m4 macro to detect at configure time how
many processors are available in order to run multiple cppcheck
jobs. This value is also now used as a replacement for nproc
when executing the kernel interface checks.
* "PHONY =" line moved in to the Rules.am file which is included
at the top of all Makefile.am's. This is just convenient becase
it allows us to use the += syntax to add phony targets.
* One upside of this integration worth mentioning is it now allows
`make cppcheck` to be run in any directory to check that subtree.
* For the moment, cppcheck is not run against the FreeBSD specific
kernel sources. The cppcheck-FreeBSD target will need to be
implemented and testing on FreeBSD to support this.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11508
Identical condition and return expression 'rc', return value is
always 0.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11508
The ASSERT that the passed pointer isn't NULL appears after the
pointer has already been dereferenced. Remove the redundant check.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11508
The double free reported for the realloc() failure branch is a
false positive. It should be resolved in cppcheck 2.4 but for
the benefit of older versions we supress the warning.
https://trac.cppcheck.net/ticket/9292
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11508
Explicitly check for NULL to satisfy cppcheck that "val" can never
be NULL when passed to printf(). This looks like a false positive
since is_blank_str() can never take the false conditional branch
when passed a NULL. But there's no harm in adding the extra check.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11508
When scrubbing, (non-sequential) resilvering, or correcting a checksum
error using RAIDZ parity, ZFS should heal any incorrect RAIDZ parity by
overwriting it. For example, if P disks are silently corrupted (P being
the number of failures tolerated; e.g. RAIDZ2 has P=2), `zpool scrub`
should detect and heal all the bad state on these disks, including
parity. This way if there is a subsequent failure we are fully
protected.
With RAIDZ2 or RAIDZ3, a block can have silent damage to a parity
sector, and also damage (silent or known) to a data sector. In this
case the parity should be healed but it is not.
The problem can be noticed by scrubbing the pool twice. Assuming there
was no damage concurrent with the scrubs, the first scrub should fix all
silent damage, and the second scrub should be "clean" (`zpool status`
should not report checksum errors on any disks). If the bug is
encountered, then the second scrub will repair the silently-damaged
parity that the first scrub failed to repair, and these checksum errors
will be reported after the second scrub. Since the first scrub repaired
all the damaged data, the bug can not be encountered during the second
scrub, so subsequent scrubs (more than two) are not necessary.
The root cause of the problem is some code that was inadvertently added
to `raidz_parity_verify()` by the DRAID changes. The incorrect code
causes the parity healing to be aborted if there is damaged data
(`rc_error != 0`) or the data disk is not present (`!rc_tried`). These
checks are not necessary, because we only call `raidz_parity_verify()`
if we have the correct data (which may have been reconstructed using
parity, and which was verified by the checksum).
This commit fixes the problem by removing the incorrect checks in
`raidz_parity_verify()`.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#11489Closes#11510
- refactor cleanup routines into common kshlib zpool_export_cleanup func
- don't require physical disks to test, just use files
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Will Andrews <will@firepipe.net>
Closes#11518
zfs-load-key.sh is called by the dracut-pre-mount.service unit which has
no explicit 'After' dependency on zfs-import.target. That way it can be
that the pool has not yet been imported and the zfs-load-key.sh finishes
without ever seeing the relevant pool.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Lorenz Hüdepohl <dev@stellardeath.org>
Closes#11500
Create a common exit point for spa_export_common (a very long
function), which avoids missing steps on failure. This work
is helpful for the planned forced pool export changes.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Will Andrews <will@firepipe.net>
Closes#11514
Instead of just failing, indicate the expected and actual value and
source as a NOTE. Tests using this failed in an earlier version of
the changeset and this information helped find the cause.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Will Andrews <will@firepipe.net>
Closes#11517
There is an identical definition in zfs_set_common.kshlib already.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Will Andrews <will@firepipe.net>
Closes#11516
This avoids globbing together multiple lines in the log, if you happen
to specify LOGAPI_DEBUG because you want to see it.
Signed-off-by: Will Andrews <will@firepipe.net>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11515
Like any other thread created by thread_create() we need to call
thread_exit() to properly clean it up. In particular, this ensures the
tsd hash for the thread is cleared.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#11512
It was observed that vdev_id exists silently when
the $CONFIG file is missing.
This patch adds error message in case vdev_id is
called without default $CONFIG or '-c'. This makes
end user observe the exit message more easily.
Before Patch:
~~~~~~~~~~~~~
$ ./cmd/vdev_id/vdev_id
$
After Patch:
~~~~~~~~~~~~
$ ./cmd/vdev_id/vdev_id
Error: Config file "/etc/zfs/vdev_id.conf" not found
$
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Arshad Hussain <arshad.hussain@aeoncomputing.com>
Closes#11498
Fix two minor errors reported by cppcheck:
In module/zfs/abd.c (abd_get_offset_impl), add non-NULL
assertion to prevent NULL dereference warning.
In module/zfs/arc.c (l2arc_write_buffers), change 'try'
variable to 'pass' to avoid C++ reserved word.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Colm Buckley <colm@tuatha.org>
Closes#11507
Follow up for commit 624222a, value asserted <= SPA_OLD_MAXBLOCKSIZE
instead of SPA_MAXBLOCKSIZE as it should be after the previous change.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#11501
When creating a pool only features supported by both user and
kernel space should be enabled. Furthermore, improve the error
messages when attempting to create, or add, a dRAID vdev when
the dRAID feature is not supported by the kernel modules.
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11492
Mixing ZIL and normal allocations has several problems:
1. The ZIL allocations are allocated, written to disk, and then a few
seconds later freed. This leaves behind holes (free segments) where the
ZIL blocks used to be, which increases fragmentation, which negatively
impacts performance.
2. When under moderate load, ZIL allocations are of 128KB. If the pool
is fairly fragmented, there may not be many free chunks of that size.
This causes ZFS to load more metaslabs to locate free segments of 128KB
or more. The loading happens synchronously (from zil_commit()), and can
take around a second even if the metaslab's spacemap is cached in the
ARC. All concurrent synchronous operations on this filesystem must wait
while the metaslab is loading. This can cause a significant performance
impact.
3. If the pool is very fragmented, there may be zero free chunks of
128KB or more. In this case, the ZIL falls back to txg_wait_synced(),
which has an enormous performance impact.
These problems can be eliminated by using a dedicated log device
("slog"), even one with the same performance characteristics as the
normal devices.
This change sets aside one metaslab from each top-level vdev that is
preferentially used for ZIL allocations (vdev_log_mg,
spa_embedded_log_class). From an allocation perspective, this is
similar to having a dedicated log device, and it eliminates the
above-mentioned performance problems.
Log (ZIL) blocks can be allocated from the following locations. Each
one is tried in order until the allocation succeeds:
1. dedicated log vdevs, aka "slog" (spa_log_class)
2. embedded slog metaslabs (spa_embedded_log_class)
3. other metaslabs in normal vdevs (spa_normal_class)
The space required for the embedded slog metaslabs is usually between
0.5% and 1.0% of the pool, and comes out of the existing 3.2% of "slop"
space that is not available for user data.
On an all-ssd system with 4TB storage, 87% fragmentation, 60% capacity,
and recordsize=8k, testing shows a ~50% performance increase on random
8k sync writes. On even more fragmented systems (which hit problem #3
above and call txg_wait_synced()), the performance improvement can be
arbitrarily large (>100x).
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Don Brady <don.brady@delphix.com>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#11389
zgenhostid(8) is used to modify or create /etc/hostid. This
administrative tool is currently installed to bindir. System utilities
are typically placed in sbin.
Modify the installation directory for zgenhostid. Additionally, track
this change in its use in dracut and the rpm installation.
Authored-by: наб <nabijaczleweli@nabijaczleweli.xyz>
Authored-by: Antonio Russo <aerusso@aerusso.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Antonio Russo <aerusso@aerusso.net>
Closes#11485
The ZFS_IOC_POOL_TRYIMPORT ioctl returns an nvlist from the kernel to a
preallocated buffer in userland. Userland must guess how large the
buffer should be. If it undersizes it, it must reallocate and try
again. That can cost a lot of time for large pools.
OpenZFS commit 28b40c8a6e set the guess at "zc.zc_nvlist_conf_size * 4"
without explanation. On my system, that is too small. From experiment,
x 32 is a better multiplier. But I don't know how to calculate it
theoretically.
Sponsored by: Axcient
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alek Pinchuk <apinchuk@axcient.com>
Signed-off-by: Alan Somers <asomers@gmail.com>
Closes#11469
As part of commit 1c2358c1 the custom uio_prefaultpages() code
was removed in favor of using the generic kernel provided
iov_iter_fault_in_readable() interface. Unfortunately, it
turns out that up until the Linux 4.7 kernel the function would
only ever fault in the first iovec of the iov_iter. The result
being uiomove_iov() may hang waiting for the page.
This commit effectively restores the custom uio_prefaultpages()
pages code for Linux 4.9 and earlier kernels which contain the
troublesome version of iov_iter_fault_in_readable().
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11463Closes#11484
In FreeBSD the struct uio was just a typedef to uio_t. In order to
extend this struct, outside of the definition for the struct uio, the
struct uio has been embedded inside of a uio_t struct.
Also renamed all the uio_* interfaces to be zfs_uio_* to make it clear
this is a ZFS interface.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Brian Atkinson <batkinson@lanl.gov>
Closes#11438
The `abd_get_offset_*()` routines create an abd_t that references
another abd_t, and doesn't allocate any pages/buffers of its own. In
some workloads, these routines may be called frequently, to create many
abd_t's representing small pieces of a single large abd_t. In
particular, the upcoming RAIDZ Expansion project makes heavy use of
these routines.
This commit adds the ability for the caller to allocate and provide the
abd_t struct to a variant of `abd_get_offset_*()`. This eliminates the
cost of allocating the abd_t and performing the accounting associated
with it (`abdstat_struct_size`). The RAIDZ/DRAID code uses this for
the `rc_abd`, which references the zio's abd. The upcoming RAIDZ
Expansion project will leverage this infrastructure to increase
performance of reads post-expansion by around 50%.
Additionally, some of the interfaces around creating and destroying
abd_t's are cleaned up. Most significantly, the distinction between
`abd_put()` and `abd_free()` is eliminated; all types of abd_t's are
now disposed of with `abd_free()`.
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Issue #8853Closes#11439
Prior to util-linux 2.36.2, if a file or directory in the
current working directory was named 'dataset' then mount(8)
would prepend the current working directory to the dataset.
Eventually, we should be able to drop this workaround.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Sterling Jensen <sterlingjensen@users.noreply.github.com>
Closes#11295Closes#11462
As described in #11445, the kernel interface kernel_{read,write} no
longer act on special devices. In the ZTS, zfs send and receive are
tested by piping to these devices, leading to spurious failures (for
positive tests) and may mask errors (for negative tests).
Until a more permanent mechanism to address this deficiency is
developed, clean up the output from the ZTS by avoiding directly piping
to or from /dev/null and /dev/zero.
For /dev/zero input, simply use a pipe: `cat </dev/zero |` .
However, for /dev/null output, the shell semantics for pipe failures
means that zfs send error codes will be masked by the successful
`| cat >/dev/null` command execution. In that case, use a temporary
file under $TEST_BASE_DIR for output in favor.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Attila Fülöp <attila@fueloep.org>
Signed-off-by: Antonio Russo <aerusso@aerusso.net>
Closes#11478
Try to use more appropriate ASSERT and VERIFY variants in ztest.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11454
The zfs_rollback_001 test modifies files in a temporary, test dataset
repeatedly. Before each iteration, any preexisting dataset is removed,
after unmounted with umount -f, if necessary.
Add a short delay after the forced unmount, avoiding a race that can
prevent zfs destroy from succeeding, leading to a test failure.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Antonio Russo <aerusso@aerusso.net>
Closes#11451
Each zfs ioctl that changes on-disk state (e.g. set property, create
snapshot, destroy filesystem) is recorded in the zpool history, and is
printed by `zpool history -i`.
For performance diagnostic purposes, it would be useful to know how long
each of these ioctls took to run. This commit adds that functionality,
with a new `ZPOOL_HIST_ELAPSED_NS` member of the history nvlist.
Additionally, the time recorded in this history log is currently the
time that the history record is written to disk. But in many cases (CLI
args logging and ioctl logging), this happens asynchronously,
potentially many seconds after the operation completed. This commit
changes the timestamp to reflect when the history event was created,
rather than when it was written to disk.
Reviewed-by: Mark Maybee <mmaybee@cray.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#11440
If the system is very low on memory (specifically,
`arc_free_memory() < arc_sys_free/2`, i.e. less than 1/16th of RAM
free), `arc_evict_state_impl()` will defer wakups. In this case, the
arc_evict_waiter_t's remain on the list, even though `arc_evict_count`
has been incremented past their `aew_count`.
The problem is that `arc_wait_for_eviction()` assumes that if there are
waiters on the list, the count they are waiting for has not yet been
reached. However, the deferred wakeups may violate this, causing
`ASSERT(last->aew_count > arc_evict_count)` to fail.
This commit resolves the issue by having new waiters use the greater of
`arc_evict_count` and the last `aew_count`.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: George Amanakis <gamanakis@gmail.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#11285Closes#11397
zfsdev_close sets zs_minor to -1 to avoid duplicate calls to
destroy. This doesn't mix well with the current u_int used.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#11437
Several m4 macros have been retired in autoconf 2.70. Update the
the build system to use the new macros provided to replace them.
* Replaced AC_HELP_STRING with AS_HELP_STRING.
* Replaced AC_TRY_COMPILE with AC_COMPILE_IFELSE/AC_LANG_PROGRAM.
* Replaced AC_CANONICAL_SYSTEM with AC_CANONICAL_TARGET
* Replaced AC_PROG_LIBTOOL with LT_INIT
* $CPP is not defined in ZFS_AC_KERNEL and really shouldn't be
directly used like this. Replace it with an $AWK command
to extract the kernel source version.
Reviewed-by: Eli Schwartz <eschwartz@archlinux.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #11413Closes#11419
if pool root is not mounted, then zpool umount in next test will leave
dataset mountpoint directory around and next zfs mount -a will fail
with error: cannot mount '/testpool': directory is not empty
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Toomas Soome <tsoome@me.com>
Closes#11417
Virtuozzo 7 kernels starting 3.10.0-1127.18.2.vz7.163.46
have the following configuration:
* no HAVE_VFS_RW_ITERATE
* HAVE_VFS_DIRECT_IO_ITER_RW_OFFSET
=> let's add implementation of zpl_direct_IO() via
zpl_aio_{read,write}() in this case.
https://bugs.openvz.org/browse/OVZ-7243
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Konstantin Khorenko <khorenko@virtuozzo.com>
Closes#11410Closes#11411
In `zpool_find_config()`, the `pools` nvlist is leaked. Part of it (a
sub-nvlist) is returned in `*configp`, but the callers also leak that.
Additionally, in `zdb.c:main()`, the `searchdirs` is leaked.
The leaks were detected by ASAN (`configure --enable-asan`).
This commit resolves the leaks.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#11396
Build error on illumos with gcc 10 did reveal:
In function 'dmu_objset_refresh_ownership':
../../common/fs/zfs/dmu_objset.c:857:25: error: implicit conversion
from 'boolean_t' to 'ds_hold_flags_t' {aka 'enum ds_hold_flags'}
[-Werror=enum-conversion]
857 | dsl_dataset_disown(ds, decrypt, tag);
| ^~~~~~~
cc1: all warnings being treated as errors
libzfs_input_check.c: In function 'zfs_ioc_input_tests':
libzfs_input_check.c:754:28: error: implicit conversion from
'enum dmu_objset_type' to 'enum lzc_dataset_type'
[-Werror=enum-conversion]
754 | err = lzc_create(dataset, DMU_OST_ZFS, NULL, NULL, 0);
| ^~~~~~~~~~~
cc1: all warnings being treated as errors
The same issue is present in openzfs, and also the same issue about
ds_hold_flags_t, which currently defines exactly one valid value.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Toomas Soome <tsoome@me.com>
Closes#11406
As of 5.11 the blk_register_region() and blk_unregister_region()
functions have been retired. This isn't a problem since add_disk()
has implicitly allocated minor numbers for a very long time.
Reviewed-by: Rafael Kitover <rkitover@gmail.com>
Reviewed-by: Coleman Kane <ckane@colemankane.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11387Closes#11390
Both revalidate_disk_size() and revalidate_disk() have been removed.
Functionally this isn't a problem because we only relied on these
functions to call zvol_revalidate_disk() for us and to perform any
additional handling which might be needed for that kernel version.
When neither are available we know there's no additional handling
needed and we can directly call zvol_revalidate_disk().
Reviewed-by: Rafael Kitover <rkitover@gmail.com>
Reviewed-by: Coleman Kane <ckane@colemankane.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11387Closes#11390
The bd_contains member was removed from the block_device structure.
Callers needing to determine if a vdev is a whole block device should
use the new bdev_whole() wrapper. For older kernels we provide our
own bdev_whole() wrapper which relies on bd_contains for compatibility.
Reviewed-by: Rafael Kitover <rkitover@gmail.com>
Reviewed-by: Coleman Kane <ckane@colemankane.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11387Closes#11390
The generic IO accounting functions have been removed in favor of the
bio_start_io_acct() and bio_end_io_acct() functions which provide a
better interface. These new functions were introduced in the 5.8
kernels but it wasn't until the 5.11 kernel that the previous generic
IO accounting interfaces were removed.
This commit updates the blk_generic_*_io_acct() wrappers to provide
and interface similar to the updated kernel interface. It's slightly
different because for older kernels we need to pass the request queue
as well as the bio.
Reviewed-by: Rafael Kitover <rkitover@gmail.com>
Reviewed-by: Coleman Kane <ckane@colemankane.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11387Closes#11390
The lookup_bdev() function has been updated to require a dev_t
be passed as the second argument. This is actually pretty nice
since the major number stored in the dev_t was the only part we
were interested in. This allows to us avoid handling the bdev
entirely. The vdev_lookup_bdev() wrapper was updated to emulate
the behavior of the new lookup_bdev() for all supported kernels.
Reviewed-by: Rafael Kitover <rkitover@gmail.com>
Reviewed-by: Coleman Kane <ckane@colemankane.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11387Closes#11390
Update the ZFS_LINUX_TEST_PROGRAM macro to always set the module
license. As of the 5.11 kernel not setting a license has been
converted from a warning to an error.
Reviewed-by: Rafael Kitover <rkitover@gmail.com>
Reviewed-by: Coleman Kane <ckane@colemankane.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11387Closes#11390
Increase the Linux-Maximum version in the META file to 5.10.
All of the required compatibility patches have been merged.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11391
Individual transactions may not be larger than DMU_MAX_ACCESS.
This is enforced by the assertions in dmu_tx_hold_write() and
dmu_tx_hold_write_by_dnode(). There's an additional check in
dmu_tx_count_write() however it has no effect and only sets a
local err variable. We could enable this check, however since
it's already enforced by ASSERTs elsewhere I opted to remove it
instead.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#3731Closes#11384
Before this patch, dracut wouldn't find zfs.ko for inclusion in
initramfs. This was caused by the packages installing in to
/lib/modules instead of /usr/lib/modules. Correcting this allows
dracut to do the right thing, even without
# /etc/dracut.conf
add_drivers+=" zfs "
Notably, rpm/redhat/zfs-kmod.spec.in does not contain the definition of
the `prefix` macro that this commit removes in the generic kmod spec.
And https://rpmfusion.org/Packaging/KernelModules/Kmods2 does not
mention `prefix` at all.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Christian Schwarz <me@cschwarz.com>
Closes#11381
Instead of creating issues with type "question"
Forward to the GitHub Discussion system.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Kjeld Schouten-Lebbing <kjeld@schouten-lebbing.nl>
Closes#11383
After porting the fix for https://github.com/openzfs/zfs/issues/5295
over to illumos, we started hitting an assertion failure when running
the testsuite:
assertion failed: rc->rc_count == number, file: .../refcount.c
and the unexpected hold has this stack:
dsl_dataset_long_hold+0x59 dmu_objset_upgrade+0x73
dmu_objset_id_quota_upgrade+0x15 dmu_objset_own+0x14f
The simplest reproducer for this in illumos is
zpool create -f -O version=1 testpool c3t0d0; zpool destroy testpool
which is run as part of the zpool_create_tempname test, but I can't get
this to trigger on FreeBSD. This appears to be because of the call to
txg_wait_synced() in dmu_objset_upgrade_stop() (which was missing in
illumos), slows down dmu_objset_disown() enough to avoid the condition.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andy Fiddaman <andy@omnios.org>
Closes#11368
The CentOS stream 4.18.0-257 kernel appears to have backported
the Linux 5.9 change to make_request_fn and the associated API.
To maintain weak modules compatibility the original symbol was
retained and the new interface blk_alloc_queue_rh() was added.
Unfortunately, blk_alloc_queue() was replaced in the blkdev.h
header by blk_alloc_queue_bh() so there doesn't seem to be a way
to build new kmods against the old interfces. Even though they
appear to still be available for weak module binding.
To accommodate this a configure check is added for the new _rh()
variant of the function and used if available. If compatibility
code gets added to the kernel for the original blk_alloc_queue()
interface this should be fine. OpenZFS will simply continue to
prefer the new interface and only fallback to blk_alloc_queue()
when blk_alloc_queue_rh() isn't available.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11374
Commit 1c2358c12 restructured this code and introduced a warning
about the variable maybe not being initialized. This cannot happen
with the updated code but we should initialize the variable anyway
to silence the warning.
zpl_file.c: In function ‘zpl_iter_write’:
zpl_file.c:324:9: warning: ‘count’ may be used uninitialized
in this function [-Wmaybe-uninitialized]
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11373
There's no need to call iov_iter_advance() in zpl_iter_read().
This was preserved from the previous code where it wasn't needed
but also didn't cause any problems. Now that the iter functions
also handle pipes that's no longer the case. When fully reading a
pipe buffer iov_iter_advance() may results in the pipe buf release
function being called which will not be registered resulting in
a NULL dereference.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11375Closes#11378
Commit 59b68723 added a configure check for 5.10, which removed
revalidate_disk(), and conditionally replaced it's usage with a call to
the new revalidate_disk_size() function. However, the old function also
invoked the device's registered callback, in our case
zvol_revalidate_disk(). This commit adds a call to zvol_revalidate_disk()
in zvol_update_volsize() to make sure the code path stays the same.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Michael D Labriola <michael.d.labriola@gmail.com>
Closes#11358
Check for the history_event type instead.
The zfs-list-cacher.sh script currently respects the event types
excluded from syslog(!) in ZED_SYSLOG_SUBCLASS_EXCLUDE.
This makes little sense in this single-purpose script and
silently breaks when history_events are excluded from syslog,
which is the default since 13d65987a9.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: InsanePrawn <insane.prawny@gmail.com>
Closes#11164Closes#11347
As of the 5.10 kernel the generic splice compatibility code has been
removed. All filesystems are now responsible for registering a
->splice_read and ->splice_write callback to support this operation.
The good news is the VFS provided generic_file_splice_read() and
iter_file_splice_write() callbacks can be used provided the ->iter_read
and ->iter_write callback support pipes. However, this is currently
not the case and only iovecs and bvecs (not pipes) are ever attached
to the uio structure.
This commit changes that by allowing full iov_iter structures to be
attached to uios. Ever since the 4.9 kernel the iov_iter structure
has supported iovecs, kvecs, bvevs, and pipes so it's desirable to
pass the entire thing when possible. In conjunction with this the
uio helper functions (i.e uiomove(), uiocopy(), etc) have been
updated to understand the new UIO_ITER type.
Note that using the kernel provided uio_iter interfaces allowed the
existing Linux specific uio handling code to be simplified. When
there's no longer a need to support kernel's older than 4.9, then
it will be possible to remove the iovec and bvec members from the
uio structure and always use a uio_iter. Until then we need to
maintain all of the existing types for older kernels.
Some additional refactoring and cleanup was included in this change:
- Added checks to configure to detect available iov_iter interfaces.
Some are available all the way back to the 3.10 kernel and are used
when available. In particular, uio_prefaultpages() now always uses
iov_iter_fault_in_readable() which is available for all supported
kernels.
- The unused UIO_USERISPACE type has been removed. It is no longer
needed now that the uio_seg enum is platform specific.
- Moved zfs_uio.c from the zcommon.ko module to the Linux specific
platform code for the zfs.ko module. This gets it out of libzfs
where it was never needed and keeps this Linux specific code out
of the common sources.
- Removed unnecessary O_APPEND handling from zfs_iter_write(), this
is redundant and O_APPEND is already handled in zfs_write();
Reviewed-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11351
Consider the test to be a success as long as the initializing pattern
is found at least once per metaslab. This indicates that at least
part of the free space was initialized. Ideally we'd check that the
pattern was written to all free space but that's much trickier so this
check is a reasonable compromise.
Using a here-string to feed the loop in this test causes an empty
string to still trigger the loop so we miss the `spacemaps=0` case.
Pipe into the loop instead.
While here, we can use `zpool wait -t initialize $TESTPOOL` to wait for
the pool to initialize.
Co-authored-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11365
The space in special devices is not included in spa_dspace (or
dsl_pool_adjustedsize(), or the zfs `available` property). Therefore
there is always at least as much free space in the normal class, as
there is allocated in the special class(es). And therefore, there is
always enough free space to remove a special device.
However, the checks for free space when removing special devices did not
take this into account. This commit corrects that.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Don Brady <don.brady@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#11329
After e357046 it should not be necessary to periodically update ARC
kstats and tunables. Tunable updates are applied when modified, and
kstats are updated on demand.
Update kstats in `arc_evict_cb_check()` for `ZFS_DEBUG` builds only.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11237
On a system with very high fragmentation, we may need to do lots of gang
allocations (e.g. most indirect block allocations (~50KB) may need to
gang). Before failing a "normal" allocation and resorting to ganging, we
try every metaslab. This has the impact of loading every metaslab (not
a huge deal since we now typically keep all metaslabs loaded), and also
iterating over every metaslab for every failing allocation. If there are
many metaslabs (more than the typical ~200, e.g. due to vdev expansion
or very large vdevs), the CPU cost of this iteration can be very
impactful. This iteration is done with the mg_lock held, creating long
hold times and high lock contention for concurrent allocations,
ultimately causing long txg sync times and poor application performance.
To address this, this commit changes the behavior of "normal" (not
try_hard, not ZIL) allocations. These will now only examine the 100
best metaslabs (as determined by their ms_weight). If none of these
have a large enough free segment, then the allocation will fail and
we'll fall back on ganging.
To accomplish this, we will now (normally) gang before doing a
`try_hard` allocation. Non-try_hard allocations will only examine the
100 best metaslabs of each vdev. In summary, we will first try normal
allocation. If that fails then we will do a gang allocation. If that
fails then we will do a "try hard" gang allocation. If that fails then
we will have a multi-layer gang block.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#11327
Metaslab rotor and aliquot are used to distribute workload between
vdevs while keeping some locality for logically adjacent blocks. Once
multiple allocators were introduced to separate allocation of different
objects it does not make much sense for different allocators to write
into different metaslabs of the same metaslab group (vdev) same time,
competing for its resources. This change makes each allocator choose
metaslab group independently, colliding with others only sporadically.
Test including simultaneous write into 4 files with recordsize of 4KB
on a striped pool of 30 disks on a system with 40 logical cores show
reduction of vdev queue lock contention from 54 to 27% due to better
load distribution. Unfortunately it won't help much ZVOLs yet since
only one dataset/ZVOL is synced at a time, and so for the most part
only one allocator is used, but it may improve later.
While there, to reduce the number of pointer dereferences change
per-allocator storage for metaslab classes and groups from several
separate malloc()'s to variable length arrays at the ends of the
original class and group structures.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#11288
Fedora does not guarantee a stable kABI, so weak modules should be dis-
abled. See the dkms man page for a more detailed explanation of the weak
module feature.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Gregory Bartholomew <gregory.lee.bartholomew@gmail.com>
Closes#9891Closes#11128Closes#11242Closes#11335
Avoid a bug with gcc's -Wreturn-local-addr warning with some
obfuscation. In buggy versions of gcc, if a return value is an
expression that involves the address of a local variable, and even if
that address is legally converted to a non-pointer type, a warning may
be emitted and the value of the address may be replaced with zero.
Howerver, buggy versions don't emit the warning or replace the value
when simply returning a local variable of non-pointer type.
https://gcc.gnu.org/bugzilla/show_bug.cgi?id=90737
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Libby <rlibby@FreeBSD.org>
Closes#11337
Building the spa module for i386 caused gcc to emit
-Wint-to-pointer-cast "cast to pointer from integer of different size"
because spa.spa_did was uint64_t but pthread_join (via thread_join in
spa_deactivate) takes a pointer (32-bit on i386). Define spa_did to be
pointer-size instead. For now spa_did is in fact never non-zero and the
thread_join could instead be ifdef'd out, but changing the size of
spa_did may be more useful for the future.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Libby <rlibby@FreeBSD.org>
Closes#11336
The last change caused the read completion callback to not be called
if the IO was still in progress. This change restores allocation
of the arc buf callback, but in the callback path checks the new
acb_nobuf field to know to skip buffer allocation.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#11324
When removing and subsequently reattaching a vdev, CKSUM errors may
occur as vdev_indirect_read_all() reads from all children of a mirror
in case of a resilver.
Fix this by checking whether a child is missing the data and setting a
flag (ic_error) which is then checked in vdev_indirect_repair() and
suppresses incrementing the checksum counter.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#11277
In an earlier revision of dRAID there existed an /etc/zfs/draid.d
directory. This was removed before the final version was integrated
but a little bit was accidentally overlooked in the zfs_helpers.sh
script. Remove this remnant.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11326
Some tunables shown by arc_summary3 have string values that may exceed
the normal line length, leaving a negative offset between the name and
value fields. The negative space is of course not valid and Python
rightly barfs up an exception traceback.
Handle an overflowing value field width by ignoring the line length
and separating the name from the value by a single space instead.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11270
There is a tunable to select the fletcher 4 checksum implementation on
Linux but it was not present in FreeBSD.
Implement the sysctl handler for FreeBSD and use ZFS_MODULE_PARAM_CALL
to provide the tunable on both platforms.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11270
The performance of `zfs receive` can be bottlenecked on the CPU consumed
by the `receive_writer` thread, especially when receiving streams with
small compressed block sizes. Much of the CPU is spent creating and
destroying dbuf's and arc buf's, one for each `WRITE` record in the send
stream.
This commit introduces the concept of "lightweight writes", which allows
`zfs receive` to write to the DMU by providing an ABD, and instantiating
only a new type of `dbuf_dirty_record_t`. The dbuf and arc buf for this
"dirty leaf block" are not instantiated.
Because there is no dbuf with the dirty data, this mechanism doesn't
support reading from "lightweight-dirty" blocks (they would see the
on-disk state rather than the dirty data). Since the dedup-receive code
has been removed, `zfs receive` is write-only, so this works fine.
Because there are no arc bufs for the received data, the received data
is no longer cached in the ARC.
Testing a receive of a stream with average compressed block size of 4KB,
this commit improves performance by 50%, while also reducing CPU usage
by 50% of a CPU. On a per-block basis, CPU consumed by receive_writer()
and dbuf_evict() is now 1/7th (14%) of what it was.
Baseline: 450MB/s, CPU in receive_writer() 40% + dbuf_evict() 35%
New: 670MB/s, CPU in receive_writer() 17% + dbuf_evict() 0%
The code is also restructured in a few ways:
Added a `dr_dnode` field to the dbuf_dirty_record_t. This simplifies
some existing code that no longer needs `DB_DNODE_ENTER()` and related
routines. The new field is needed by the lightweight-type dirty record.
To ensure that the `dr_dnode` field remains valid until the dirty record
is freed, we have to ensure that the `dnode_move()` doesn't relocate the
dnode_t. To do this we keep a hold on the dnode until it's zio's have
completed. This is already done by the user-accounting code
(`userquota_updates_task()`), this commit extends that so that it always
keeps the dnode hold until zio completion (see `dnode_rele_task()`).
`dn_dirty_txg` was previously zeroed when the dnode was synced. This
was not necessary, since its meaning can be "when was this dnode last
dirtied". This change simplifies the new `dnode_rele_task()` code.
Removed some dead code related to `DRR_WRITE_BYREF` (dedup receive).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: George Wilson <gwilson@delphix.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#11105
In the redaction list traversal code, there is a bug in the binary search
logic when looking for the resume point. Maxbufid can be decremented to -1,
causing us to read the last possible block of the object instead of the one we
wanted. This can cause incorrect resume behavior, or possibly even a hang in
some cases. In addition, when examining non-last blocks, we can treat the
block as being the same size as the last block, causing us to miss entries in
the redaction list when determining where to resume. Finally, we were ignoring
the case where the resume point was found in the buffer being searched, and
resuming from minbufid. All these issues have been corrected, and the code has
been significantly simplified to make future issues less likely.
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#11297
vfs.zfs.arc_no_grow_shift has an invalid type (15) and this causes
py-sysctl to format it as a bytearray when it should be an integer.
"U" is not a valid format, it should be "I" and the type should match
the variable type, int. We can return EINVAL if the value is set below
zero.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11318
py-sysctl now includes the CTLTYPE_NODE type nodes in the list returned
by sysctl.filter() on FreeBSD head. It also provides descriptions now.
Eliminate the subprocess call to get descriptions, and filter out the
nodes so we only deal with values.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11318
Resolve an uninitialized variable warning when compiling.
In function ‘zfs_domount’:
warning: ‘root_inode’ may be used uninitialized in this
function [-Wmaybe-uninitialized]
sb->s_root = d_make_root(root_inode);
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11306
ZFS currently doesn't react to hotplugging cpu or memory into the
system in any way. This patch changes that by adding logic to the ARC
that allows the system to take advantage of new memory that is added
for caching purposes. It also adds logic to the taskq infrastructure
to support dynamically expanding the number of threads allocated to a
taskq.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Matthew Ahrens <matthew.ahrens@delphix.com>
Co-authored-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#11212
There has been a panic affecting some system configurations where the
thread FPU context is disturbed during the fletcher 4 benchmarks,
leading to a panic at boot.
module_init() registers zcommon_init to run in the last subsystem
(SI_SUB_LAST). Running it as soon as interrupts have been configured
(SI_SUB_INT_CONFIG_HOOKS) makes sure we have finished the benchmarks
before we start doing other things.
While it's not clear *how* the FPU context was being disturbed, this
does seem to avoid it.
Add a module_init_early() macro to run zcommon_init() at this earlier
point on FreeBSD. On Linux this is defined as module_init().
Authored by: Konstantin Belousov <kib@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11302
Tracking down an error message with the errno value can be difficult,
using strerror makes the error message clearer.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Érico Rolim <erico.erc@gmail.com>
Closes#11303
Add ARC_FLAG_NO_BUF to indicate that a buffer need not be
instantiated. This fixes a ~20% performance regression on
cached reads due to zfetch changes.
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#11220Closes#11232
The fnvlist_lookup_boolean_value() function should not be used
to check the force argument since it's optional. It may not be
provided or may have been created with the wrong flags.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11281Closes#11284
Run zfs-tests with sanity.run for brief results. Timeouts
are rare, so minimize false positives by increasing the
default from 60 to 180 seconds.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Melikov <mail@gmelikov.ru>
Closes#11304
During module load time all of the available fetcher4 and raidz
implementations are benchmarked for a fixed amount of time to
determine the fastest available. Manual testing has shown that this
time can be significantly reduced with negligible effect on the final
results.
This commit changes the benchmark time to 1ms which can reduce the
module load time by over a second on x86_64. On an x86_64 system
with sse3, ssse3, and avx2 instructions the benchmark times are:
Fletcher4 603ms -> 15ms
RAIDZ 1,322ms -> 64ms
Reviewed-by: Matthew Macy <mmacy@freebsd.org>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11282
Since 8c4fb36a24 (PR #7795) spa_has_pending_synctask() started to
take two more locks per write inside txg_all_lists_empty(). I am
surprised those pool-wide locks are not contended, but still their
operations are visible in CPU profiles under contended vdev lock.
This commit slightly changes vdev_queue_max_async_writes() flow to
not call the function if we are going to return max_active any way
due to high amount of dirty data. It allows to save some CPU time
exactly when the pool is busy.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-By: Tom Caputi <caputit1@tcnj.edu>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#11280
With both abd_size and abd_nents being uint_t it makes no sense for
abd_chunkcnt_for_bytes() to return size_t. Random mix of different
types used to count chunks looks bad and makes compiler more difficult
to optimize the code.
In particular on FreeBSD this change allows compiler to completely
optimize out abd_verify_scatter() when built without debug, removing
pointless 64-bit division and even more pointless empty loop.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#11279
Extend the CI checkstyle workflow to perform the library ABI
checks in the master branch. The intent is not to prevent any
ABI changes but to detect them immediately so when they're
made it's done intentionally.
When the changing the ABI the `make storeabi` target can be
used to generate a new .abi file which can be included with
the commit. This depends on the libabigail utility which is
available from the majority of distribution package managers.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11287
When running in the CI the zpool_import_012_pos test case occasionally
takes longer than the maximum 600 seconds. When this happens the test
case is considered to have failed but always completes a few minutes
latter. Since the logs suggest nothing has actually failed this commit
increases timeout and removes the exception.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11286
Occasionally an out of memory error is hit by this test case
when mounting the filesystems. Try and reduce the likelihood
of this occurring by reducing the thread count from 100 to 50.
It also has the advantage of slightly speeding up the test.
cannot mount 'testpool/testfs3/79': Cannot allocate memory
filesystem successfully created, but not mounted
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11283
When sending raw encrypted datasets the user space accounting is present
when it's not expected to be. This leads to the subsequent mount failure
due a checksum error when verifying the local mac.
Fix this by clearing the OBJSET_FLAG_USERACCOUNTING_COMPLETE and reset
the local mac. This allows the user accounting to be correctly updated
on first mount using the normal upgrade process.
Reviewed-By: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-By: Tom Caputi <caputit1@tcnj.edu>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#10523Closes#11221
`zpool create -n` fails to list cache and spare vdevs.
`zpool add -n` fails to list spare devices.
`zpool split -n` fails to list `special` and `dedup` labels.
`zpool add -n` and `zpool split -n` shouldn't list hole devices.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Attila Fülöp <attila@fueloep.org>
Closes#11122Closes#11167
This run file contains a subset of functional tests which exercise
as much functionality as possible while still executing relatively
quickly. The included tests should take no more than a few seconds
each to run at most. This provides a convenient way to sanity test a
change before committing to a full test run which takes several hours.
$ ./scripts/zfs-tests.sh -r sanity
...
Results Summary
PASS 813
Running Time: 00:14:42
Percent passed: 100.0%
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11271
It was found that setting min_active tunables for non-interactive I/Os
makes them stuck. It is caused by zfs_vdev_nia_delay, that can never
be reached if we never issue any I/Os due to min_active set to zero.
Fix this by issuing at least one non-interactive I/O at a time when
there are no interactive I/Os. When there are interactive I/Os, zero
min_active allows to completely block any non-interactive I/O. It may
min_active starvation in some scenarios, but who we are to deny foot
shooting?
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#11261
Busybox's mktemp requires at least six X's in the template, causing
the current sed --in-place check to fail because the file does not
exist. This change adds additional X's to mktemp templates that do
not already have at least six X's in them.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Quentin Zdanis <zdanisq@gmail.com>
Closes#11269
In function dmu_buf_hold_array_by_dnode, the usage of zio is only for
the reading operation. Only create the zio and wait it in the reading
scenario as a performance optimization.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Finix Yan <yancw@info2soft.com>
Closes#11251Closes#11256
When ZFS_COLOR is set, zpool status shows row headings in bold,
except for the "remove:" heading. This is a quick fix that makes
it print in bold too.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andrew Sun <me@andrewsun.com>
Closes#11255
Move the zpool_influxdb command to /usr/libexec/zfs,
and include the /usr/libexec/zfs path in the system search
directory when running the test suite.
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Pavel Snajdr <snajpa@snajpa.net>
Closes#11156Closes#11160Closes#11224
Extend the change made in ae12b02 to verify the zfs kernel
modules are loaded to the rest of the OpenZFS services. If
the modules aren't loaded the neither the share, volume, or
and zed services can be started.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11243
Despite that dracut has a hard dependency on bash,
its modules doesn't, dracut only has a hard dependency on bash for
module-setup (on a fully usable machine). Inside initramfs, dracut
allows users choose from a list of handful other shells, e.g. bash,
busybox, dash, mkfsh.
In fact, my local machine's initramfs is being built with dash,
and it's functional for a very long time.
Before 64025fa3a (Silence 'make checkbashisms', 2020-08-20), we also
allows our users to have that right, too.
Let's fix the problem 'make checkbashisms' reported and allows our users
to have that right, again.
For 'plymouth' case, let's simply run the command inside the if instead
of checking for the existence of command before running it, because the
status is also failture if plymouth is unavailable.
While we're at it, let's remove an unnecessary fork for grep in
zfs-generator.sh.in and its following complicated 'if elif fi' with
a simple 'case ... esac'.
To support this change, also exclude 90zfs from "make checkbashisms"
because the current CI infrastructure ships an old version of
"checkbashisms", which complains about "command -v", while the current
latest "checkbashisms" thinks it's fine. In the near future, we can
revert that change to "Makefile.am" when CI infrastructure is updated.
Reviewed-by: Gabriel A. Devenyi <gdevenyi@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Đoàn Trần Công Danh <congdanhqx@gmail.com>
Closes#11244
Commit 85703f6 added a new ASSERT to zfs_write() as part of the
cleanup which isn't correct in the case where multiple processes
are concurrently extending a file. The `zp->z_size` is updated
atomically while holding a range lock on only a portion of the
file. Therefore, it's possible for the file size to increase
after a same check is performed earlier in the loop causing this
ASSERT to fail. The code itself handles this case correctly so
only the invalid ASSERT needs to be removed.
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11235
Investigating influence of scrub (especially sequential) on random read
latency I've noticed that on some HDDs single 4KB read may take up to 4
seconds! Deeper investigation shown that many HDDs heavily prioritize
sequential reads even when those are submitted with queue depth of 1.
This patch addresses the latency from two sides:
- by using _min_active queue depths for non-interactive requests while
the interactive request(s) are active and few requests after;
- by throttling it further if no interactive requests has completed
while configured amount of non-interactive did.
While there, I've also modified vdev_queue_class_to_issue() to give
more chances to schedule at least _min_active requests to the lowest
priorities. It should reduce starvation if several non-interactive
processes are running same time with some interactive and I think should
make possible setting of zfs_vdev_max_active to as low as 1.
I've benchmarked this change with 4KB random reads from ZVOL with 16KB
block size on newly written non-fragmented pool. On fragmented pool I
also saw improvements, but not so dramatic. Below are log2 histograms
of the random read latency in milliseconds for different devices:
4 2x mirror vdevs of SATA HDD WDC WD20EFRX-68EUZN0 before:
0, 0, 2, 1, 12, 21, 19, 18, 10, 15, 17, 21
after:
0, 0, 0, 24, 101, 195, 419, 250, 47, 4, 0, 0
, that means maximum latency reduction from 2s to 500ms.
4 2x mirror vdevs of SATA HDD WDC WD80EFZX-68UW8N0 before:
0, 0, 2, 31, 38, 28, 18, 12, 17, 20, 24, 10, 3
after:
0, 0, 55, 247, 455, 470, 412, 181, 36, 0, 0, 0, 0
, i.e. from 4s to 250ms.
1 SAS HDD SEAGATE ST14000NM0048 before:
0, 0, 29, 70, 107, 45, 27, 1, 0, 0, 1, 4, 19
after:
1, 29, 681, 1261, 676, 1633, 67, 1, 0, 0, 0, 0, 0
, i.e. from 4s to 125ms.
1 SAS SSD SEAGATE XS3840TE70014 before (microseconds):
0, 0, 0, 0, 0, 0, 0, 0, 70, 18343, 82548, 618
after:
0, 0, 0, 0, 0, 0, 0, 0, 283, 92351, 34844, 90
I've also measured scrub time during the test and on idle pools. On
idle fragmented pool I've measured scrub getting few percent faster
due to use of QD3 instead of QD2 before. On idle non-fragmented pool
I've measured no difference. On busy non-fragmented pool I've measured
scrub time increase about 1.5-1.7x, while IOPS increase reached 5-9x.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#11166
In order for package managers such as dnf to upgrade cleanly after
the package SONAME bump the obsolete package names must be known.
Update the new packages to correctly obsolete the old ones.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11230Closes#11233
The documentation describes dRAID as a distributed spare, not
parity, RAID implementation. Update the short feature description
to match the rest of the documentation.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11229
We do not build libnvpair.pc. Moreover, it is automatically pulled in
by libzfs.pc, so no additional specific dependency is required.
Reviewed by: Toomas Soome <tsoome@me.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Antonio Russo <aerusso@aerusso.net>
Closes#11227
Name of dataset for user home directory may vary from the expected
$homes_prefix/$username, if different naming scheme is being used.
We can use property mountpoint to specify the dataset for $username
as long as its value is identical to passwd's pw_dir.
For example:
NAME PROPERTY VALUE
rpool/home/myuser_123456 mountpoint /home/myuser
Reviewed-by: Felix Dörre <felix@dogcraft.de>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Crag Wang <crag0715@gmail.com>
Closes#11165
The ABI should be included when generating the `make dist` tarball
since it's required by the `make checkabi` target.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11225
Commit a1d477c2 accidentally disabled DTL updates for the zil_claim()
case described at the end of vdev_stat_update() by unconditionally
disabling all DTL updates when loading. This was done to avoid
a deadlock on the vd_dtl_lock when loading the DTLs from disk.
vdev_dtl_contains <--- Takes vd->vd_dtl_lock
vdev_mirror_child_missing
vdev_mirror_io_start
zio_vdev_io_start
__zio_execute
arc_read
dbuf_issue_final_prefetch
dbuf_prefetch_impl
dbuf_prefetch
dmu_prefetch
space_map_iterate
space_map_load_length
space_map_load
vdev_dtl_load <--- Takes vd->vd_dtl_lock
vdev_load
spa_ld_load_vdev_metadata
spa_tryimport
The missing DTL updates can be restored by moving the space_map_load()
call outside the vd_dtl_lock. A private range tree is populated by
reading the space map and then merged in to the DTL_MISSING tree
under the lock.
Furthermore, the SPA_LOAD_NONE check in vdev_dtl_contains() leads to an
additional problem. Any resilvering which occurs before SPA_LOAD_NONE
is set will incorrectly determine that there's nothing to repair. This
can result in full redundancy not being restored for some blocks.
Reviewed-by: Matt Ahrens <matt@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11218
RPM and DEB packages are named after the SONAME version of the library
they contain. After bumping this version, the packaging should be
renamed.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Antonio Russo <aerusso@aerusso.net>
Closes#11219
Bring over some of the improvements from dracut/zfs-load-key.sh,
shellcheck is slightly quieter as well
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11198
The loop now has a less confusing condition and properly uses
systemctl(1) is-failed's return code instead of that entire mess
The assignments could turn into "var=val program" if encryptionroot
or keylocation had whitespace in them
As a bonus, this (mostly) silences shellcheck
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11198
Is this block when abuf != NULL ever reached? Yes, it is.
Add asserts and comments to prove that when we get here, we have a full
block write at an aligned offset extending past EOF.
Simplify by removing the check that tx_bytes == max_blksz, since we can
assert that it is always true.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11191
- Don't leave fstrans set when passed a snapshot
- Don't remove minor if volmode already matches new value
- (FreeBSD) Wait for GEOM ops to complete before trying
remove (at create time GEOM will be "tasting" in parallel)
- (FreeBSD) Don't leak zvol_state_lock on open if zv == NULL
- (FreeBSD) Don't try to unlock zv->zv_state lock if zv == NULL
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#11199
Add a snapshot of the current ABI using libabigail-1.7-2. The
included ABI passes `make checkabi` for CentOS 7, Fedora 33,
Debian 10, and Ubuntu 20.04. This covers a fairly wide range
of glibc, gcc, and libabigail versions plus other changes which
are platform specific.
Reviewed-by: Antonio Russo <aerusso@aerusso.net>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11144
Provide two make targets: checkabi and storeabi.
storeabi uses libabigail to generate a reference copy of the ABI for the
public libraries.
checkabi compares such a reference to the compiled version, failing if
they are not compatible. No ABI is generated for libzpool.so, it is
only used by ztest and zdb and not external consumers.
Co-authored-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Antonio Russo <aerusso@aerusso.net>
Closes#11144
zpool_expand_proplist() now ignores pl_fixed if its new literal
argument is true. The rest is a consequence of needing to pass
that down.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiao?=~Dska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11202
For encrypted receives, where user accounting is initially disabled on
creation, both 'zfs userspace' and 'zfs groupspace' fails with
EOPNOTSUPP: this is because dmu_objset_id_quota_upgrade_cb() forgets to
set OBJSET_FLAG_USERACCOUNTING_COMPLETE on the objset flags after a
successful dmu_objset_space_upgrade().
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#9501Closes#9596
In case of cache device removal it is possible that at the end of
l2arc_evict() we have l2ad_hand = l2ad_evict. This can lead to the
following panic in case of a debug build:
VERIFY3(dev->l2ad_hand < dev->l2ad_evict) failed (321920512 < 321920512)
Call Trace:
dump_stack+0x66/0x90
spl_panic+0xef/0x117 [spl]
l2arc_remove_vdev+0x11d/0x290 [zfs]
spa_load_l2cache+0x275/0x5b0 [zfs]
spa_vdev_remove+0x4a5/0x6e0 [zfs]
zfs_ioc_vdev_remove+0x59/0xa0 [zfs]
zfsdev_ioctl_common+0x5b3/0x630 [zfs]
zfsdev_ioctl+0x53/0xe0 [zfs]
do_vfs_ioctl+0x42e/0x6b0
ksys_ioctl+0x5e/0x90
do_syscall_64+0x5b/0x1a0
entry_SYSCALL_64_after_hwframe+0x44/0xa9
In case of cache device removal it also possible that l2ad_hand +
distance > l2ad_end since we do not iterate l2arc_evict() and l2ad_hand
is not reset. This has no functional consequence however as the cache
device is about to be removed.
Fix this by omitting the ASSERT in case of device removal.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#11205
On systems with musl libc, hostid(1) always prints "00000000", which
will cause improper behavior when the 90zfs module is configured in a
dracut initramfs. Work around this by copying the host /etc/hostid if
the file exists, and otherwise only write /etc/hostid if hostid(1)
returns something meaningful. This avoids zgenhostid creating a random
/etc/hostid for the initramfs, which could lead to errors when trying to
import the pool if spl_hostid isn't defined in the kernel command line.
Furthermore, tag the /etc/hostid file as hostonly, since it is system
specific and shouldn't be taken into account when trying to use an
initramfs generated in one system to boot into a different system.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Georgy Yakovlev <gyakovlev@gentoo.org>
Co-authored-by: Andrew J. Hesford <ajh@sideband.org>
Signed-off-by: Érico Rolim <erico.erc@gmail.com>
Closes#11174Closes#11189
A common usage pattern for zgenhostid, including in the ZFS dracut
module, is running it as:
zgenhostid $(hostid)
However, zgenhostid only accepted hostid arguments greater than 0, which
meant that, when the output of hostid(1) was "00000000", zgenhostid
would error out, even though 0 is a possible return value for the
gethostid(3) function used by hostid(1):
- On current musl libc, gethostid(3) is a stub that always returns 0.
- On glibc, gethostid(3) will return 0 if /etc/hostid exists but is
smaller than 4 bytes.
In these cases, it makes more sense for zgenhostid to treat a value of 0
as other parts of the zfs codebase do, meaning that a hostid value
couldn't be determined; therefore, it should attempt to generate a
random value to write into /etc/hostid.
The manpage and usage output have been updated to reflect this.
Whitespace has also been fixed in the usage output.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Georgy Yakovlev <gyakovlev@gentoo.org>
Reviewed-by: Andrew J. Hesford <ajh@sideband.org>
Signed-off-by: Érico Rolim <erico.erc@gmail.com>
Closes#11174Closes#11189
The ZFS_ENTER/ZFS_EXIT/ZFS_VERFY_ZP macros should not be used
in the Linux zpl_*.c source files. They return a positive error
value which is correct for the common code, but not for the Linux
specific kernel code which expects a negative return value. The
ZPL_ENTER/ZPL_EXIT/ZPL_VERFY_ZP macros should be used instead.
Furthermore, the ZPL_EXIT macro has been updated to not call the
zfs_exit_fs() function. This prevents a possible deadlock which
can occur when a snapshot is automatically unmounted because the
zpl_show_devname() must never wait on in progress automatic
snapshot unmounts.
Reviewed-by: Adam Moss <c@yotes.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11169Closes#11201
The output of ZFS channel programs is logged on-disk in the zpool
history, and printed by `zpool history -i`. Channel programs can use
10MB of memory by default, and up to 100MB by using the `zfs program -m`
flag. Therefore their output can be up to some fraction of 100MB.
In addition to being somewhat wasteful of the limited space reserved for
the pool history (which for large pools is 1GB), in extreme cases this
can result in a failure of `ASSERT(length <= DMU_MAX_ACCESS);` in
`dmu_buf_hold_array_by_dnode()`.
This commit limits the output size that will be logged to 1MB. Larger
outputs will not be logged, instead a entry will be logged indicating
the size of the omitted output.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#11194
FreeBSD's VFS expects EFAULT from zfs_write() if we didn't complete
the full write so it can retry the operation. Add some missing
SET_ERRORs in zfs_write().
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11193
This patch adds a new top-level vdev type called dRAID, which stands
for Distributed parity RAID. This pool configuration allows all dRAID
vdevs to participate when rebuilding to a distributed hot spare device.
This can substantially reduce the total time required to restore full
parity to pool with a failed device.
A dRAID pool can be created using the new top-level `draid` type.
Like `raidz`, the desired redundancy is specified after the type:
`draid[1,2,3]`. No additional information is required to create the
pool and reasonable default values will be chosen based on the number
of child vdevs in the dRAID vdev.
zpool create <pool> draid[1,2,3] <vdevs...>
Unlike raidz, additional optional dRAID configuration values can be
provided as part of the draid type as colon separated values. This
allows administrators to fully specify a layout for either performance
or capacity reasons. The supported options include:
zpool create <pool> \
draid[<parity>][:<data>d][:<children>c][:<spares>s] \
<vdevs...>
- draid[parity] - Parity level (default 1)
- draid[:<data>d] - Data devices per group (default 8)
- draid[:<children>c] - Expected number of child vdevs
- draid[:<spares>s] - Distributed hot spares (default 0)
Abbreviated example `zpool status` output for a 68 disk dRAID pool
with two distributed spares using special allocation classes.
```
pool: tank
state: ONLINE
config:
NAME STATE READ WRITE CKSUM
slag7 ONLINE 0 0 0
draid2:8d:68c:2s-0 ONLINE 0 0 0
L0 ONLINE 0 0 0
L1 ONLINE 0 0 0
...
U25 ONLINE 0 0 0
U26 ONLINE 0 0 0
spare-53 ONLINE 0 0 0
U27 ONLINE 0 0 0
draid2-0-0 ONLINE 0 0 0
U28 ONLINE 0 0 0
U29 ONLINE 0 0 0
...
U42 ONLINE 0 0 0
U43 ONLINE 0 0 0
special
mirror-1 ONLINE 0 0 0
L5 ONLINE 0 0 0
U5 ONLINE 0 0 0
mirror-2 ONLINE 0 0 0
L6 ONLINE 0 0 0
U6 ONLINE 0 0 0
spares
draid2-0-0 INUSE currently in use
draid2-0-1 AVAIL
```
When adding test coverage for the new dRAID vdev type the following
options were added to the ztest command. These options are leverages
by zloop.sh to test a wide range of dRAID configurations.
-K draid|raidz|random - kind of RAID to test
-D <value> - dRAID data drives per group
-S <value> - dRAID distributed hot spares
-R <value> - RAID parity (raidz or dRAID)
The zpool_create, zpool_import, redundancy, replacement and fault
test groups have all been updated provide test coverage for the
dRAID feature.
Co-authored-by: Isaac Huang <he.huang@intel.com>
Co-authored-by: Mark Maybee <mmaybee@cray.com>
Co-authored-by: Don Brady <don.brady@delphix.com>
Co-authored-by: Matthew Ahrens <mahrens@delphix.com>
Co-authored-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mark Maybee <mmaybee@cray.com>
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#10102
ZFS channel programs (invoked by `zfs program`) are executed in a LUA
sandbox with a limit on the amount of memory they can consume. The
limit is 10MB by default, and can be raised to 100MB with the `-m` flag.
If the memory limit is exceeded, the LUA program exits and the command
fails with a message like `Channel program execution failed: Memory
limit exhausted.`
The LUA sandbox allocates memory with `vmem_alloc(KM_NOSLEEP)`, which
will fail if the requested memory is not immediately available. In this
case, the program fails with the same message, `Memory limit exhausted`.
However, in this case the specified memory limit has not been reached,
and the memory may only be temporarily unavailable.
This commit changes the LUA memory allocator `zcp_lua_alloc()` to use
`vmem_alloc(KM_SLEEP)`, so that we won't spuriously fail when memory is
temporarily low. Instead, we rely on the system to be able to free up
memory (e.g. by evicting from the ARC), and we assume that even at the
highest memory limit of 100MB, the channel program will not truly
exhaust the system's memory.
External-issue: DLPX-71924
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#11190
The custom zpl_show_devname() helper should translate spaces in
to the octal escape sequence \040. The getmntent(2) function
is aware of this convention and properly translates the escape
character back to a space when reading the fsname.
Without this change the `zfs mount` and `zfs unmount` commands
incorrectly detect when a dataset with a name containing spaces
is mounted.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11182Closes#11187
It is a leftover from illumos always set to NULL and introducing a
spurious difference between zio_buf and zio_data_buf.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#11188
The microzap hash can sometimes be zero for single digit snapnames.
The zap cursor can then have a serialized value of two (for . and ..),
and skip the first entry in the avl tree for the .zfs/snapshot directory
listing, and therefore does not return all snapshots.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Cedric Berger <cedric@precidata.com>
Signed-off-by: Tony Perkins <tperkins@datto.com>
Closes#11039
This looks like it was once from the illumnos compat code.
FreeBSD doesn't have cmn_err as a compiler format attribute, so
it definitely errors out.
It doesn't show up on LLVM because it doesn't trigger at all.
Add in the format flags but keep them behind #if 0 for now;
there are too many format issues that trigger when one does
format checking in the shared code.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: adrian chadd <adrian@freebsd.org>
Closes#11068Closes#11069
This shows up when compiling freebsd-head on amd64 using gcc-6.4.
The lib32 compat build ends up tripping over this assumption.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: adrian chadd <adrian@freebsd.org>
Closes#11068Closes#11069
Remove reference to EFI(?), explain that the new space
is beyond the GPT for whole-disk vdevs, and add section noting how it
behaves with partition vdevs in terms of how the user is most likely to
encounter it ‒ the previous phrasing was confusing
and seemed to indicate that "zpool online -e" will be able to claim
GPT[whatever, ZFS, free space, whatever]
into
GPT[whatever, ZFS, whatever]
but that's not the case, as it'll only be able to do so after manually
resizing the ZFS partition to include the free space beforehand, i.e.:
GPT[whatever, ZFS, free space, whatever]
GPT[whatever, [ZFS + free space], potentially left-overs, whatever]
# zpool online -e
GPT[whatever, ZFS, whatever]
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11158
The copy_exec() function expects that the full path of the target
file is passed rather than just the directory, and will take care
of creating the underlying directories if they don't exist.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Closes#11162
We can consolidate the unlocking procedure into one place by starting
with drop_suspend set to B_FALSE and moving the open count check up.
While here, a little code cleanup. Match the out labels between
zvol_geom_open and zvol_cdev_open, and add a missing period in some
comments.
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11175
zvol_first_open can fail with EINTR if spa_namespace_lock is not held
and cannot be taken without waiting.
Apply the same logic that was done for zvol_geom_open to take
spa_namespace_lock if not already held on first open in zvol_cdev_open.
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11175
After initial arc_c was reduced to arc_c_min it became possible that
on datasets with primarycache=metadata or none dirty data make up most
of ARC capacity and easily more than configured 50% of initial arc_c,
that causes forced txg commits by arc_tempreserve_space() and periodic
very long write delays.
This patch makes arc_tempreserve_space() to use arc_c only after ARC
warmed up once and arc_c really means something, but use arc_c_max
before that.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#11178
Fix a couple of places where the wrong tag is passed
to dnode_{hold, rele}
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#11184
Add a new test case which corrupts all level 1 block in a file.
Then verifies that corruption is detected and repaired.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11141
The second part of list_file_blocks transforms the object description
output by zdb -ddddd $ds $objnum into a stream of lines of the form
"level path offset length" for the indirect blocks in the given file.
The current code only works for the first copy of L0 blocks. L1 and
L2 indirect blocks have more than one copy on disk.
Add one more -d to the zdb command so we get all block copies and
rewrite the transformation to match more than L0 and output all DVAs.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11141
The first part of list_file_blocks transforms the pool configuration
output by zdb -C $pool into shell code to set up a shell variable,
VDEV_MAP, that maps from vdev id to the underlying vdev path. This
variable is a simple indexed array. However, the vdev id in a DVA is
only the id of the top level vdev.
When the pool is mirrored, the top level vdev is a mirror and its
children are the mirrored devices. So, what we need is to map from
the top level vdev id to a list of the underlying vdev paths.
ist_file_blocks does not need to work for raidz vdevs, so we can
disregard that case.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11141
Check if the ZVOL has been written before calling zil_async_to_sync.
The ZIL will be opened on the first write, not earlier.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Mariusz Zaborski <oshogbo@vexillium.org>
Closes#11152
spa_config_load() passes NULL into resid when doing zfs_file_read().
This would trip over when vfs.zfs.autoimport_disable=0.
Sponsored by: The FreeBSD Foundation
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Ka Ho Ng <khng@freebsdfoundation.org>
Closes#11149
Bump library SOVERSION under Linux to match FreeBSD's.
Additionally, this bump properly accounts for the ABI changes relative
to ZoL 0.8.5 for the Linux build.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Antonio Russo <aerusso@aerusso.net>
Issue #11144
SET_ERROR is useful to trace errors, so use it where the errors occur
rather than factored out to the end of a function.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11146
The expected variance for this test case was originally set at 10%
based on local testing. Additional testing via the CI has show it
can be as large as 11%. Increase the expected maximum to 12% to
prevent this test from incorrectly failing.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11148
The events_001_pos.ksh test case can fail because it's possible,
and correct, for the config_sync event to be posted after the last
"expected" event. To accommodate this the run_and_verify() function
has been updated to wait for all non-history events, not just the
last event. This does not increase the run time of the test as
long as all the events do get generated.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11147
A new function was added named revalidate_disk_size() and the old
revalidate_disk() appears to have been deprecated. As the only ZFS
code that calls this function is zvol_update_volsize, swapping the
old function call out for the new one should be all that is required.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#11085
Kernel 5.10 removed check_disk_change() in favor of callers using
the faster bdev_check_media_change() instead, and explicitly forcing
bdev revalidation when they desire that behavior. To preserve prior
behavior, I have wrapped this into a zfs_check_media_change() macro
that calls an inline function for the new API that mimics the old
behavior when check_disk_change() doesn't exist, and just calls
check_disk_change() if it exists.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#11085
Kernel commit 2b0d3d3e4fcfb brought in some changes to the struct
percpu_ref structure that moves most of its fields into a member
struct named "data" of type struct percpu_ref_data. This includes
the "count" member which is updated by vdev_blkg_tryget(), so update
this function to chase the API change, and detect it via configure.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#11085
In Linux 5.10 the linux/frame.h header was renamed linux/objtool.h.
Add a configure check to detect and use the correctly named header.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11085
Avoid checking the whole array of objects each time by removing the self
organized memory reaping. this can be managed by the global memory reap
callback which is called every 60 seconds. this will reduce the use if
locking operations significant.
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Reviewed-by: Mateusz Guzik <mjguzik@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Closes#11126
Move zfs_get_data() in to platform-independent code. The only
platform-specific aspect of it is the way we release an inode
(Linux) / vnode_t (FreeBSD). I am not aware of a platform that
could be supported by ZFS that couldn't implement zfs_rele_async
itself. It's sibling zvol_get_data already is platform-independent.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Christian Schwarz <me@cschwarz.com>
Closes#10979
Current CPU_SEQID users don't care about possibly changing CPU ID, but
enclose it within kpreempt disable/enable in order to fend off warnings
from Linux's CONFIG_DEBUG_PREEMPT.
There is no need to do it. The expected way to get CPU ID while allowing
for migration is to use raw_smp_processor_id.
In order to make this future-proof this patch keeps CPU_SEQID as is and
introduces CPU_SEQID_UNSTABLE instead, to make it clear that consumers
explicitly want this behavior.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#11142
The zfs_holey() and zfs_access() functions can be made common
to both FreeBSD and Linux.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#11125
zvol private data is supposed to be nulled by zvol_clear_private before
zvol_free is called as an indicator that the zvol is going away.
Implement zvol_clear_private for volmode=dev.
Assert that zvol_clear_private has been called before zvol_free.
Check that zvol_clear_private has not been called when updating
volsize. If it has, fail with ENXIO.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11117
We fall back to a default volmode and continue when looking up a zvol's
volmode property fails. After this we should set the error to 0 to
ensure we take the success paths in the out section.
While here, make sure we only log that the zvol was created on success.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11117
zvol_geom_close gets a count of the number of close operations to do.
Make sure we're always using this count to check if this will be the
last close operation performed on the zvol.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11117
Using more specific assert variants gives better messages on failure.
No functional change.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11117
Note that this only tracks sizes as requested by the caller.
Actual allocated space will almost always be bigger (e.g., rounded up to
the next power of 2 or page size). Additionally the allocated buffer may
be holding other areas hostage. Nonetheless, this is a starting point
for tracking memory usage in zstd.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#11129
While evaluating other assembler implementations it turns out that
the precomputed hash subkey tables vary in size, from 8*16 bytes
(avx2/avx512) up to 48*16 bytes (avx512-vaes), depending on the
implementation.
To be able to handle the size differences later, allocate
`gcm_Htable` dynamically rather then having a fixed size array, and
adapt consumers.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Attila Fülöp <attila@fueloep.org>
Closes#11102
AT_BENEATH was merged to stable/12, where kern_unlinkat takes a
non-const path. DECONST the path passed to kern_unlinkat in the
case where AT_BENEATH is defined.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11139
The original xuio zero copy functionality has always been unused
on Linux and FreeBSD. Remove this disabled code to avoid any
confusion and improve readability.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#11124
L2ARC devices of several terabytes filled with 4KB blocks may take 15
minutes to rebuild. Due to the way L2ARC log reading is implemented
it is quite likely that for all that time rebuild thread will never
sleep. At least on FreeBSD kernel threads have absolute priority and
can not be preempted by threads with lower priorities. If some thread
is also bound to that specific CPU it may not get any CPU time for all
the 15 minutes.
Reviewed-by: Cedric Berger <cedric@precidata.com>
Reviewed-by: Ryan Moeller <freqlabs@FreeBSD.org>
Reviewed-by: George Amanakis <gamanakis@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#11116
ZFS always waits for the write completion before flushing the cache.
That is why it does not require explicit ordering fences around it,
which are pretty difficult to implement for NVMe, since one has no
internal concept of strict request ordering.
This was already removed from FreeBSD once, but got resurrected
by mistake during OpenZFS merge.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#11130
Previously, xattr_004_pos would create files with xattrs on both
tmpfs and ext2, and then copy them to zfs to verify that their
xattrs were preserved. However tmpfs doesn't support xattrs.
This was never noticed until Fedora 33. In Fedora 32 and older,
/tmp was on the root partition (like ext4), whereas on Fedora 33
/tmp is actually tmpfs. That caused this test to fail on Fedora 33.
This fix updates the test to only create the file on ext2, not tmpfs.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#11133
The port removed provisions for zfs_znode_move but the cleanup missed
this bit. To quote the original:
[snip]
list_insert_tail(&zfsvfs->z_all_znodes, zp);
membar_producer();
/*
* Everything else must be valid before assigning z_zfsvfs makes the
* znode eligible for zfs_znode_move().
*/
zp->z_zfsvfs = zfsvfs;
[/snip]
In the current code it is immediately followed by unlock which issues
the same fence, thus plays no role in correctness.
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#11115
The Linux kernel MODULE_LICENSE macro only recognizes a handful of
license strings and "MIT" is not one of the them. Update the macro
to use "Dual MIT/GPL" which is recognized and what the kernel expects
MIT licensed modules to use.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11112Closes#11113
These kstats are often expensive to compute so we want to avoid them
unless specifically requested.
The following kstats are affected by this change:
kstat.zfs.${pool}.multihost
kstat.zfs.${pool}.misc.state
kstat.zfs.${pool}.txgs
kstat.zfs.misc.fletcher_4_bench
kstat.zfs.misc.vdev_raidz_bench
kstat.zfs.misc.dbufs
kstat.zfs.misc.dbgmsg
In FreeBSD 13, sysctl(8) has been updated to still list the
names/description/type of skipped sysctls so they are still
discoverable.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Mateusz Guzik <mjguzik@gmail.com>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11099
Use proper names (i.e. zfs-allow and zpool-add) in NAME subsections
of zfs/zpool subcommands instead of current "pretty-printed" ones as
makewhatis utilities (or some implementations of it, namely the one
from mandoc suite used in FreeBSD) look not only at the document title
but also in NAME subsection, adding zfs(8)/zpool(8) to search results
which is not correct. (Common sense and other utilities splitting
subcommands in multiple man pages, e.g. git, do the same.)
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: xtouqh <xtouqh@hotmail.com>
Closes#11086
The zfs_fsync, zfs_read, and zfs_write function are almost identical
between Linux and FreeBSD. With a little refactoring they can be
moved to the common code which is what is done by this commit.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#11078
The current l2_misses accounting behavior treats all reads to pools
without a configured l2arc as an l2arc miss, IFF there is at least
one other pool on the system which does have an l2arc configured.
This makes it extremely hard to tune for an improved l2arc hit/miss
ratio because this ratio will be modulated by reads from pools which
do not (and should not) have l2arc devices; its upper limit will
depend on the ratio of reads from l2arc'd pools and non-l2arc'd pools.
This PR prevents ARC reads affecting l2arc stats (n.b. l2_misses is
the only relevant one) where the target spa doesn't have an l2arc.
Includes new test - l2arc_l2miss_pos.ksh
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Amanakis <gamanakis@gmail.com>
Signed-off-by: Adam Moss <c@yotes.com>
Closes#10921
This was removed in a reorganization of directories preparing for the
merge of FreeBSD support, 006e9a4088 by mmacy. While llvm is perfectly
happy with the nonexistent -I directory, the gcc6 and gcc9 we can elect
to use as cross-toolchains both trip over it.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Kyle Evans <kevans@FreeBSD.org>
Closes#11077
ZED will log zevents summaries to the syslog, however the log entries
tend to drop event details that can be useful for diagnosis. This is
especially true for ereport events, like io, checksum, and delay.
Update the all-syslog.sh script to log additional event information.
Add an optional config option, ZED_SYSLOG_DISPLAY_GUIDS, to zed.rc
for choosing GUIDs over names for pool and vdev.
Change the default ZED_SYSLOG_SUBCLASS_EXCLUDE to exclude history_event
events. These events tend to be frequent, convey no meaningful info,
and are already logged in the zpool history.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@delphix.com>
Closes#10967
The removal of a vdev in the normal class would fail if there was a
special or deup vdev that had a different ashift than the vdevs in
the normal class.
Moved the initialization of spa_min_ashift / spa_max_ashift from
vdev_open so that it occurs after the vdev allocation bias was
initialized (i.e. after vdev_load).
Caveat -- In order to remove a special/dedup vdev it must have the
same ashift as the normal pool vdevs. This could perhaps be lifted
in the future (i.e. for the case where there is ample space in any
surviving special class vdevs)
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@delphix.com>
Closes#9363Closes#9364Closes#11053
This is a follow up fix for commit 0fdd6106bb. The VERIFY is
only true when we haven't hit an error code path. See added
test case for a reproducer.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Christian Schwarz <me@cschwarz.com>
Closes#11048
After a side-effectful call like add or remove, references to range
segs stored in btrees can no longer be used safely. We move the
remove call to just before the reinsertion call so that the seg
remains valid for as long as we need it.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#11044Closes#11056
The 32-bit counter eventually wraps to 0 which is a sentinel for invalid
id.
Make it 64-bit on LP64 platforms and 0-check otherwise.
Note: Linux counterpart uses id stored per queue instead of a global.
I did not check going that way is feasible with the goal being the
minimal fix doing the job.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#11059
The acltype property is currently hidden on FreeBSD and does not
reflect the NFSv4 style ZFS ACLs used on the platform. This makes it
difficult to observe that a pool imported from FreeBSD on Linux has a
different type of ACL that is being ignored, and vice versa.
Add an nfsv4 acltype and expose the property on FreeBSD.
Make the default acltype nfsv4 on FreeBSD.
Setting acltype to an unhanded style is treated the same as setting
it to off. The ACLs will not be removed, but they will be ignored.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10520
In FreeBSD, there are three compile environments that are supported:
user land, the kernel and the bootloader / standalone. Adjust the
headers to compile in the standalone environment. Limit kernel-only
items from view when _STANDALONE is defined.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Warner Losh <imp@FreeBSD.org>
Closes#10998
Currently streams are only freed when:
- They have no referencing zfetch and and their I/O references
go to zero.
- They are more than 2s old and a new I/O request comes in on
the same zfetch.
This means that we will leak unreferenced streams when their zfetch
structure is freed.
This change checks the reference count on a stream at zfetch free
time. If it is zero we free it immediately. If it has remaining
references we allow the prefetch callback to free it at I/O
completion time.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Adam Moss <c@yotes.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#11052
The zstd code assumes that if you are on aarch64, you have NEON
instructions. This is not necessarily true. In a boot loader, where
you might not have the VFP properly initialized, these instructions
may not be available. It's also an error to include arm_neon.h when
the NEON insturctions aren't enabled. Change the guards for using the
NEON instructions from __aarch64__ to __ARM_NEON which is the standard
symbol for knowing if they are available.
__ARM_NEON is the proper symbol, defined in ARM C Language Extensions
Release 2.1 (https://developer.arm.com/documentation/ihi0053/d/). Some
sources suggest __ARM_NEON__, but that's the obsolete spelling from
prior versions of the standard.
Updated based on zstd pull request https://github.com/facebook/zstd/pull/2356
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Warner Losh <imp@bsdimp.com>
Closes#11055
If modules fail to unload because of outstanding users, don't
consider this a success.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Adam Moss <c@yotes.com>
Closes#11042
Missing struct initialization in a config test results in the
interface being incorrectly detected.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Adam Moss <c@yotes.com>
Signed-off-by: Mathieu Velten <matmaul@gmail.com>
Closes#10713Closes#11049
This increases the Linux kernel version to 5.9 from 5.8
as most compatibility fixes should already be included.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Pavel Snajdr <snajpa@snajpa.net>
Signed-off-by: Kjeld Schouten-Lebbing <kjeld@schouten-lebbing.nl>
Closes#11050
It is a common mistake to have failed to autoload the module due to
permission issues when running a ZFS command as a user. "Operation
not permitted" is an unhelpfully vague error message.
Use a thread-local message buffer to format a nicer error message.
We can infer that loading the kernel module failed if the module is
not loaded. This can be extended with heuristics for other errors
in the future.
While looking at this stuff, remove an unused thread-local message
buffer found in libspl and remove some inaccurate verbiage from the
comment on libzfs_load_module.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11033
FreeBSD had this value tunable before the switch to the new OpenZFS.
The tunable name has changed, breaking legacy compat.
Restore legacy compat for this tunable, properly expose the tunable
with the new name on all platforms, and document it in
zfs-module-parameters(5).
While here, clean up the documentation for zfetch_max_distance a bit.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11038
A zpool_influxdb command is introduced to ease the collection
of zpool statistics into the InfluxDB time-series database.
Examples are given on how to integrate with the telegraf
statistics aggregator, a companion to influxdb.
Finally, a grafana dashboard template is included to show
how pool latency distributions can be visualized in a
ZFS + telegraf + influxdb + grafana environment.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Richard Elling <Richard.Elling@RichardElling.com>
Closes#10786
The value of zp is used without having been initialized under some
conditions. Initialize the pointer to NULL.
Add a regression test case using chown in acl/posix. However, this is
not enough because the setup sets xattr=sa, which means zfs_setattr_dir
will not be called. Create a second group of acl tests in acl/posix-sa
duplicating the acl/posix tests with symlinks, and remove xattr=sa from
the original acl/posix tests. This provides more coverage for the
default xattr=on code.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10043Closes#11025
This change updates the documentation to refer to the project
as OpenZFS instead ZFS on Linux. Web links have been updated
to refer to https://github.com/openzfs/zfs. The extraneous
zfsonlinux.org web links in the ZED and SPL sources have been
dropped.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11007
A missing semicolon between kmoddir variable declaration and the
uninstall for loop caused modules_uninstall-Linux to fail with:
Syntax error: "do" unexpected
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Jacob Adams <jacob@tookmund.com>
Closes#11032
When running libzpool with the Undefined Behavior Sanitizer (ubsan)
enabled, a zpool create causes a run-time error:
module/zfs/vdev_label.c:600:14: runtime error: shift exponent 64 is
too large for 64-bit type 'long long unsigned int'`
in vdev_config_generate()
Fix is to convert vdev_removal_max_span to its base-2 logarithm, using
highbit64(), and then compare the "shifts".
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Chuck Tuffli <ctuffli@gmail.com>
Closes#9744Closes#11024
fixup of 196bee4
On gcc (GCC) 9.2.1 20190827 (Red Hat 9.2.1-1), the code removed
caused `-Wmaybe-uninitialized` errors.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Christian Schwarz <me@cschwarz.com>
Closes#11021
With procfs_list kstats implemented for FreeBSD, dbufs are now exposed
as kstat.zfs.misc.dbufs.
On FreeBSD, dbufstats can use the sysctl instead of procfs when no
input file has been given.
Enable the dbufstats tests on FreeBSD.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#11008
Code cleanup. Sort includes, remove duplicates, and drop
some extra blank lines in kmod_core.c.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#11000
Instead of relying on arbitrary timers after pool export/import or cache
device off/online rely on arcstats. This makes the L2ARC tests more
robust. Also cleanup some functions related to persistent L2ARC.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Adam Moss <c@yotes.com>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#10983
We were missing an include for kernel FPU functions, breaking the build
on FreeBSD 12.1-RELEASE. This was apparently being pulled in from
elsewhere on stable/12 and head.
Sorted the other includes in these files while here.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11005
When resuming an interrupted ZFS send stream that creates a new dataset
with the same name as an existing dataset, if the existing dataset is
accessed after the failed receive, then after the subsequent successful
receive it will return EIO. This happens because nothing mounts the new
dataset, leaving the old, no longer valid dataset still mounted.
This commit fixes zfs receive to always unmount and remount the
destination, regardless of whether the stream is a new stream or a
resumed stream.
Sponsored by: Axcient
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alan Somers <asomers@gmail.com>
External-issue: https://bugs.freebsd.org/bugzilla/show_bug.cgi?id=249579Closes#10995Closes#10999
In C, const indicates to the reader that mutation will not occur.
It can also serve as a hint about ownership.
Add const in a few places where it makes sense.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#10997
This causes "zfs send -vt ..." to fail with:
cannot resume send: Unknown error 1030
It turns out that some of the name/value pairs in the verification
list for zfs_ioc_send_space(), zfs_keys_send_space, had the wrong
name, so the ioctl got kicked out in zfs_check_input_nvpairs().
Update the names accordingly.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: John Poduska <jpoduska@datto.com>
Closes#10978
The kernel seq_read() helper function expects ->next() to update
the passed position even there are no more entries. Failure to
do so results in the following warning being logged.
seq_file: buggy .next function procfs_list_seq_next [spl]
did not update position index
Functionally there is no issue with the way procfs_list_seq_next()
is implemented and the warning is harmless. However, we want to
silence this some what scary incorrect warning. This commit
updates the Linux procfs code to advance the position even for
the last entry.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#10984Closes#10996
The request number is out of bounds of the platform table.
Subtract the starting offset to get the correct subscript.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10994
`dbuf_stats_hash_table_data` can take much longer than it needs to
by repeatedly bzeroing its buffer when in fact the buffer only needs
to be NULL terminated.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10993
In non regular use cases allocated memory might stay persistent in memory
pool. This small patch checks every minute if there are old objects which
can be released from memory pool.
Right now with regular use, the pool is checked for old objects on each
allocation attempt from this pool. so basically polling by its use. Now
consider what happens if someone writes a lot of files and stops use of
the volume or even unmounts it. So the code will no longer check if
objects can be released from the pool. Already allocated objects will
still stay in pool cache. this is no big issue for common use. But
someone discovered this issue while doing tests. personally i know this
behavior and I'm aware of it. Its no big issue. just a enhancement
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Kjeld Schouten-Lebbing <kjeld@schouten-lebbing.nl>
Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Closes#10938Closes#10969
When an invalid incremental send is requested where the "to" ds is
before the "from" ds, make sure to drop the reference to the pool
and the dataset before returning the error.
Add an assert on FreeBSD to make sure we don't hold any locks after
returning from an ioctl.
Add some test coverage.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10919
Add community compatibility patches for Intel QAT
Due to incompatibility with higher kernel versions.
Also includes basic instructions.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Kjeld Schouten-Lebbing <kjeld@schouten-lebbing.nl>
Closes#10961Closes#10962
The Linux kernel MODULE_LICENSE macro only recognizes a handful of
license strings and "BSD" is not one of the them. Update the macro
to use "Dual BSD/GPL" which is recognized and what the kernel expects
BSD licensed module to use.
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#10982Closes#10992
This check was accidentally broken when the kABI checks were updated
to run in parallel, commit 608f874. The check must be for the
config_debug_lock_alloc_license name to determine if the symbol
is license compatible.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#10991
The m4 objtool configure check can incorrectly fail because of a
missing header in the test. This appears to be the result of a
recent kernel change and was observed on the Fedora 5.8.11-200
kernel.
In file included from /home/fedora/zfs/build/objtool/objtool.c:75:
./arch/x86/include/asm/frame.h:100:57: error: 'struct pt_regs'
declared inside parameter list will not be visible outside
of this definition or declaration [-Werror]
The consequence of this is that the "stack_frame_non_standard"
check is never run and HAVE_STACK_FRAME_NON_STANDARD is set
incorrectly which results in a build failure. This change adds
the appropriate header to the "objtool" check so it now behaves
as intended.
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#10990
The error returned by `zpool remove` when the encryption keys aren't
loaded isn't very helpful. Furthermore, the man pages make no
mention that the keys need to be loaded. This change doesn't resolve
the error message but it does update the man page to mention this
requirement.
Authored-by: grodik <pat@litke.dev>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#10939Closes#10948
This change documents the currently used branching structure.
It has been cut down to not include any controversial changes.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Kjeld Schouten-Lebbing <kjeld@schouten-lebbing.nl>
Closes#10976
The current dmu_zfetch code implicitly assumes that I/Os complete
within min_sec_reap seconds. With async dmu and a readonly workload
(and thus no exponential backoff in operations from the "write
throttle") such as L2ARC rebuild it is possible to saturate the drives
with I/O requests. These are then effectively compounded with prefetch
requests.
This change reference counts streams and prevents them from being
recycled after their min_sec_reap timeout if they still have
outstanding I/Os.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10900
Change zfs userspace subcommand to use zfs_path_to_zhandle() so that
the provided dataset can be a path (/usr) or a dataset (rpool/usr).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Closes#8915
Prefetching of dnodes in dbuf_read() can cause significant mutex
contention for some workloads and isn't very helpful. This is
because we already get 32 dnodes for each block read, and when
iterating over a directory we prefetch the dnodes in the directory.
Disable this prefetching to prevent the lock contention.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Submitted-by: Adam Moss <c@yotes.com>
Submitted-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Adam Moss <c@yotes.com>
Closes#10877Closes#10953
With PREEMPTION=y and BLK_CGROUP=y preempt_schedule_notrace() is being
used on arm64 which is a GPL-only function and hence the build of the
DKMS kernel module fails.
Fix that by redefining preempt_schedule_notrace() to preempt_schedule()
which should be safe as long as tracing is not used.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Juerg Haefliger <juergh@canonical.com>
Closes#8545Closes#9948Closes#10416Closes#10973
Address some unused value and control flow issues flagged by Coverity.
Unreachable code is pruned and unused values are avoided.
Some scattered sections are reordered for coherence.
We can assume kmem_alloc(n, KM_SLEEP) doesn't fail, so there is no need
to check if it returned NULL. The allocated memory doesn't need to be
zeroed, other than the last iovec (the MAC).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10884
If the /etc/exports.d directory does not exist, then we should only
create it when we're performing an action which already requires root
privileges.
This commit moves the directory creation to the enable/disable code
path which ensures that we have the appropriate privileges.
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Wilson <gwilson@delphix.com>
Closes#10785Closes#10934
lr_write_t records that are WR_COPIED have the record data directly
appended to them (see lr_write_t type definition).
The data is copied from the debuf using dmu_read_by_dnode.
This function was called, only for WR_COPIED records, as part of a
short-circuiting if-statement's if-expression.
I found this side-effectful call to dmu_read_by_dnode pretty
hard to spot.
This patch improves readability by moving the call to its own line.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Wilson <gwilson@delphix.com>
Signed-off-by: Christian Schwarz <me@cschwarz.com>
Closes#10956
The procfs_list interface is required by several kstats. Implement
this functionality for FreeBSD to provide access to these kstats.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10890
Resolves an issue with `zfs send` streams from 0.8.4 which
prevents them from being received by versions < 0.7.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Paul Zuchowski <pzuchowski@datto.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#10911Closes#10916
Commit 45152dc removed clearing of L2CACHE flag in arc_read_done() and
moved related code in l2arc_write_eligible(). After careful code
inspection arc_read_done() is not bypassed in the case of prefetches.
Thus restore the old behavior.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: adam moss <c@yotes.com>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#10951
In commit cd32b4f5b7 ("Fix a deadlock in the FreeBSD getpages VOP") I
introduced a bug while porting the patch originally committed to
FreeBSD: the rangelock pointer may be NULL if the try operation failed,
so we must avoid calling zfs_rangelock_unlock() in that case.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Reported-by: Steve Wills <swills@FreeBSD.org>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#10519Closes#10960
Use the same reduced buffer size for lauxlib that is used on Linux.
Fixes panic on HEAD in lua gsub test designed to exhaust stack space.
With this we can remove the special case to reserve more stack space
on FreeBSD.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Kyle Evans <kevans@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10959
Without this, the sysctl system calls will acquire a global lock before
invoking the handler. This is noticeable in some situations when
running top(1). The global lock is mostly vestigal but continues to see
some use and so contention is still a problem; until the default sense
of the MPSAFE flag changes, we have to annotate each and every handler.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#10836
with regard to evicted_l2_eligibile_mru. Even if l2arc_mfuonly is
enabled, this is not reflected in evicted_l2_eligible_mru as this
information is useful for deciding whether to toggle l2arc_mfuonly
depending on the current workload.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#10945
== Motivation and Context
The new vdev ashift optimization prevents the removal of devices when
a zfs configuration is comprised of disks which have different logical
and physical block sizes. This is caused because we set 'spa_min_ashift'
in vdev_open and then later call 'vdev_ashift_optimize'. This would
result in an inconsistency between spa's ashift calculations and that
of the top-level vdev.
In addition, the optimization logical ignores the overridden ashift
value that would be provided by '-o ashift=<val>'.
== Description
This change reworks the vdev ashift optimization so that it's only
set the first time the device is configured. It still allows the
physical and logical ahsift values to be set every time the device
is opened but those values are only consulted on first open.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Cedric Berger <cedric@precidata.com>
Signed-off-by: George Wilson <gwilson@delphix.com>
External-Issue: DLPX-71831
Closes#10932
When expanding a device zfs needs to rescan the partition table to
get the correct size. This can only happen when we're in the kernel
and requires the device to be closed. As part of the rescan, udev is
notified and the device links are removed and recreated. This leave a
window where the vdev code may try to reopen the device before udev
has recreated the link. If that happens, then the pool may end up in
a suspended state.
To correct this, we leverage the BLKPG_RESIZE_PARTITION ioctl which
allows the partition information to be modified even while it's in use.
This ioctl also does not remove the device link associated with the zfs
data partition so it eliminates the race condition that can occur in
the kernel.
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Wilson <gwilson@delphix.com>
Closes#10897
When a device removal is in progress, there are 2 locations for the data
that's already been moved: the original location, on the device that's
being removed; and the new location, which is pointed to by the indirect
mapping. When doing leak detection, zdb needs to know about both
locations. To determine what's already been copied, we load the
spacemaps of the removing vdev, omit the blocks that are yet to be
copied, and then use the vdev's remap op to find the new location.
The problem is with an optimization to the spacemap-loading code in zdb.
When processing the log spacemaps, we ignore entries that are not
relevant because they are past the point that's been copied. However,
entries which span the point that's been copied (i.e. they are partly
relevant and partly irrelevant) are processed normally. This can lead
to an illegal spacemap operation, for example if offsets up to 100KB
have been copied, and the spacemap log has the following entries:
ALLOC 50KB-150KB (partly relevant)
FREE 50KB-100KB (entirely relevant)
FREE 100KB-150KB (entirely irrlevant - ignored)
ALLOC 50KB-150KB (partly relevant)
Because the entirely irrelevant entry was ignored, its space remains in
the spacemap. When the last entry is processed, we attempt to add it to
the spacemap, but it partially overlaps with the 100-150KB entry that
was left over.
This problem was discovered by ztest/zloop.
One solution would be to also ignore the irrelevant parts of
partially-irrelevant entries (i.e. when processing the ALLOC 50-150, to
only add 50-100 to the spacemap). However, this commit implements a
simpler solution, which is to remove this optimization entirely. I.e.
to process the entire spacemap log, without regard for the point that's
been copied. After reconstructing the entire allocatable range tree,
there's already code to remove the parts that have not yet been copied.
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
External-issue: DLPX-71820
Closes#10920
In zpl_mount_impl, there is:
dmu_objset_hold ; returns with pool & ds held
dsl_pool_rele
sget
dsl_dataset_rele
As spelled out in the "DSL Pool Configuration Lock" in dsl_pool.c,
this requires a long hold.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Paul Zuchowski <pzuchowski@datto.com>
Signed-off-by: John Poduska <jpoduska@datto.com>
Closes#10936
A small bug did slip into initial libzfsbootenv; while storing nvlist
in nvlist, we should make sure the bootenv is using VB_NVLIST format.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Toomas Soome <tsoome@me.com>
Closes#10937
Prefer acltype=off|posix, retaining the old names as aliases.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10918
It was discovered that dracut scripts and zgenhostid
always generate little-endian /etc/hostid.
This commit provides simple endianess-aware binary
and updates the scripts to use it.
New features include:
-f flag to force overwrite.
-o flag to write to different file (for dracut)
accepting both 0x01234567 and 01234567 values as input
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Signed-off-by: Georgy Yakovlev <gyakovlev@gentoo.org>
Closes#10887Closes#10925
nvlist does allow us to support different data types and systems.
To encapsulate user data to/from nvlist, the libzfsbootenv library is
provided.
Reviewed-by: Arvind Sankar <nivedita@alum.mit.edu>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Signed-off-by: Toomas Soome <tsoome@me.com>
Closes#10774
Use ZFS_ENTER and ZFS_EXIT to protect datasets while their mount
devname is being retrieved.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10892Closes#10927
Currently the ARC state (MFU/MRU) of cached L2ARC buffer and their
content type is unknown. Knowing this information may prove beneficial
in adjusting the L2ARC caching policy.
This commit adds L2ARC arcstats that display the aligned size
(in bytes) of L2ARC buffers according to their content type
(data/metadata) and according to their ARC state (MRU/MFU or
prefetch). It also expands the existing evict_l2_eligible arcstat to
differentiate between MFU and MRU buffers.
L2ARC caches buffers from the MRU and MFU lists of ARC. Upon caching a
buffer, its ARC state (MRU/MFU) is stored in the L2 header
(b_arcs_state). The l2_m{f,r}u_asize arcstats reflect the aligned size
(in bytes) of L2ARC buffers according to their ARC state (based on
b_arcs_state). We also account for the case where an L2ARC and ARC
cached MRU or MRU_ghost buffer transitions to MFU. The l2_prefetch_asize
reflects the alinged size (in bytes) of L2ARC buffers that were cached
while they had the prefetch flag set in ARC. This is dynamically updated
as the prefetch flag of L2ARC buffers changes.
When buffers are evicted from ARC, if they are determined to be L2ARC
eligible then their logical size is recorded in
evict_l2_eligible_m{r,f}u arcstats according to their ARC state upon
eviction.
Persistent L2ARC:
When committing an L2ARC buffer to a log block (L2ARC metadata) its
b_arcs_state and prefetch flag is also stored. If the buffer changes
its arcstate or prefetch flag this is reflected in the above arcstats.
However, the L2ARC metadata cannot currently be updated to reflect this
change.
Example: L2ARC caches an MRU buffer. L2ARC metadata and arcstats count
this as an MRU buffer. The buffer transitions to MFU. The arcstats are
updated to reflect this. Upon pool re-import or on/offlining the L2ARC
device the arcstats are cleared and the buffer will now be counted as an
MRU buffer, as the L2ARC metadata were not updated.
Bug fix:
- If l2arc_noprefetch is set, arc_read_done clears the L2CACHE flag of
an ARC buffer. However, prefetches may be issued in a way that
arc_read_done() is bypassed. Instead, move the related code in
l2arc_write_eligible() to account for those cases too.
Also add a test and update manpages for l2arc_mfuonly module parameter,
and update the manpages and code comments for l2arc_noprefetch.
Move persist_l2arc tests to l2arc.
Reviewed-by: Ryan Moeller <freqlabs@FreeBSD.org>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#10743
The zfs-initramfs package has never worked as no RPM-based distribution
uses initramfs-tools, which is listed as a dependency of zfs-initramfs.
This would not ordinarily be a problem, as it is only enabled when
/usr/share/initramfs-tools is present, which should not normally be the
case on RPM-based distributions. However, other packages may install
unused files there even if initramfs-tools is not used, so remove this
auto-detection for the rpm-utils target.
This does not fully remove the logic for the zfs-initramfs package. This
splits it out into a separate rpm-utils-initramfs target so that the
Debian builds can still use it.
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Harald van Dijk <harald@gigawatt.nl>
Closes#10898
libzutil depends on libnvpair, but this dependency is undeclared in the
build system. Therefore it isn't possible to make a new command that
depends on libzutil, but does not (directly) depend on libnvpair.
This commit makes this dependency explicit.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reivewed-by: Ryan Moeller <freqlabs@FreeBSD.org>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#10915
The lock is taken all the time and as a regular read-write lock
avoidably serves as a mount point-wide contention point.
This forward ports FreeBSD revision r357322.
To quote aforementioned commit:
Sample result doing an incremental -j 40 build:
before: 173.30s user 458.97s system 2595% cpu 24.358 total
after: 168.58s user 254.92s system 2211% cpu 19.147 total
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <freqlabs@FreeBSD.org>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#10896
This solves issues occurring with a different decimal operator and
keeps the command line interface consistent for all locales .
E.g. `zfs set quota=0.5T`
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Felix Neumärker <xdch47@posteo.de>
Closes#10878
A great deal of time may go by between when mmp_init() is called and
the MMP thread starts, particularly if there are bad devices, because
there is I/O checking configs etc. If this time is too long,
(gethrtime() - mmp_last_write) > mmp_fail_ns
at the time the MMP thread starts. If MMP is configured to suspend
the pool, the pool will be suspended immediately.
This can be seen in issue #10838
The value of mmp_last_write doesn't matter before the mmp thread
starts. To give the MMP thread time to issue and land MMP writes,
initialize mmp_last_write when the MMP thread starts.
Reviewed-by: Giuseppe Di Natale <guss80@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#10873
We only need the kernel interfaces in crypto, not the device node in
cryptodev.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10901
In certain workloads it may be beneficial to reduce wear of L2ARC
devices by not caching MRU metadata and data into L2ARC. This commit
introduces a new tunable l2arc_mfuonly for this purpose.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#10710
When hz > 1000, msec / (1000 / hz) results in division by zero.
I found somewhere in FreeBSD using howmany(msec * hz, 1000) to convert
ms to ticks, avoiding the potential for a zero in the divisor.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#10894
The pbkdf2iters property is an iteration counter
and should be displayed as plain number rather
than in binary unit.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Fabio Buso <buso.fabio@gmail.com>
Closes#10871
On musl libc, zfs failed to compile due to the missing <fcntl.h>
include, which is required for `open()` per POSIX.
This commit add the missing <fcntl.h> include.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Hiếu Lê <leorize+oss@disroot.org>
Closes#10880
On FreeBSD, if priorities divided by four (RQ_PPQ) are equal then
a difference between them is insignificant. In other words,
incrementing pri by only one as on Linux is insufficient.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10872
Several of the listed library dependencies are not relevant on FreeBSD.
Have ./configure save libraries that are found via pkg-config as
${LIB}_PC and use the configured automake variables instead of hard
coded names so we only get what was actually needed.
While here, update the URL to point at the OpenZFS Github repo.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10869
Commit d4a72f2 which introduced multi-phase scrubs and resilvers
continued the work presented by Nexenta at the 2016 ZFS developer
summit. Update the source to reflect their contribution.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Duplicate io and checksum ereport events can misrepresent that
things are worse than they seem. Ideally the zpool events and the
corresponding vdev stat error counts in a zpool status should be
for unique errors -- not the same error being counted over and over.
This can be demonstrated in a simple example. With a single bad
block in a datafile and just 5 reads of the file we end up with a
degraded vdev, even though there is only one unique error in the pool.
The proposed solution to the above issue, is to eliminate duplicates
when posting events and when updating vdev error stats. We now save
recent error events of interest when posting events so that we can
easily check for duplicates when posting an error.
Reviewed by: Brad Lewis <brad.lewis@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@delphix.com>
Closes#10861
If a `zfs_space_check_t` other than `ZFS_SPACE_CHECK_NONE` is used with
`dsl_sync_task_nowait()`, the sync task may fail due to ENOSPC.
However, there is no way to notice or communicate this failure, so it's
extremely difficult to use this functionality correctly, and in fact
almost all callers use `ZFS_SPACE_CHECK_NONE`.
This commit removes the `zfs_space_check_t` argument from
`dsl_sync_task_nowait()`, and always uses `ZFS_SPACE_CHECK_NONE`.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#10855
When created, a zthr is given a name to identify it by. This name is
lost when a cancelled zthr is resumed.
Retain the name of a zthr so it can be used when resuming.
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10881
There are a number of places where cv_?_sig is used simply for
accounting purposes but the surrounding code has no ability to
cope with actually receiving a signal. On FreeBSD it is possible
to send signals to individual kernel threads so this could
enable undesirable behavior.
This patch adds routines on Linux that will do the same idle
accounting as _sig without making the task interruptible. On
FreeBSD cv_*_idle are all aliases for cv_*
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10843
As mentioned in the #OpenZFS IRC channel (thanks "Toomas Soome"):
The OpenZFS PR Template still mentions "ZFS on Linux".
This changes that reference and updates the URLs.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Garrett Fields <ghfields@gmail.com>
Closes#10868
Added comments in following files
with links to Illumos manual pages:
./module/avl/avl.c
./module/nvpair/nvpair.c
./module/os/linux/spl/spl-kstat.c
./module/os/freebsd/spl/spl_kstat.c
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Spencer Kinny <spencerkinny1995@gmail.com>
Closes#5113Closes#10859
Those macros are also defined by the compiler-provided float.h which
will be included later on (at least in the FreeBSD buildworld case) and
triggers these -Werror warnings. Including <float.h> first and only
defining the macros when DBL_DIG/FLT_DIG is missing fixes this problem.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alex Richardson <Alexander.Richardson@cl.cam.ac.uk>
Closes#10864
Use ZFS_MODULE_PARAM for cross-platform tunables in spa_stats.c, and
add update tunables.cfg in tests for the newly supported ones.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10858
Moving spa_stats added the additional burden of supporting
KSTAT_TYPE_IO.
spa_state_addr will always return a valid value regardless of
the value of 'n'. On FreeBSD this will cause an infinite loop
as it relies on the raw ops addr routine to indicate that there
is no more data.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <freqlabs@FreeBSD.org>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10860
Allow to rename file systems without remounting if it is possible.
It is possible for file systems with 'mountpoint' property set to
'legacy' or 'none' - we don't have to change mount directory for them.
Currently such file systems are unmounted on rename and not even
mounted back.
This introduces layering violation, as we need to update
'f_mntfromname' field in statfs structure related to mountpoint (for
the dataset we are renaming and all its children).
In my opinion it is worth it, as it allow to update FreeBSD in even
cleaner way - in ZFS-only configuration root file system is ZFS file
system with 'mountpoint' property set to 'legacy'. If root dataset is
named system/rootfs, we can snapshot it (system/rootfs@upgrade), clone
it (system/oldrootfs), update FreeBSD and if it doesn't boot we can
boot back from system/oldrootfs and rename it back to system/rootfs
while it is mounted as /. Before it was not possible, because
unmounting / was not possible.
Authored by: Pawel Jakub Dawidek <pjd@FreeBSD.org>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported by: Matt Macy <mmacy@freebsd.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10839
FreeBSD has the concept of jails, a precursor to Solaris's zones, which
can be mapped to the required zones interface with relative ease. The
previous ZFS implementation in FreeBSD did so, and we should continue
to provide an appropriate implementation in OpenZFS as well.
Move lib/libspl/zone.c into platform code and adopt the correct
implementation for FreeBSD.
While here, prune unused code.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#10851
FreeBSD's previous ZFS implemented INGLOBALZONE(thread) as
(!jailed((thread)->td_ucred)) and passed curthread to INGLOBALZONE.
We pass curproc instead of curthread, so we can achieve the same effect
with (!jailed((proc)->p_ucred)). The implementation is trivial enough
to fit on a single line in a define. We don't really need a whole
separate function for something that's already macros all the way down.
Eliminate in_globalzone.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#10851
The previous ZFS implementation on FreeBSD had ifdefs to use jailed()
instead of crgetzoneid() in dsl_dir.c, however we can simply provide an
appropriate definition of crgetzoneid for the same effect.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#10851
Initially it was considered simplest to stub out all
of the functions on FreeBSD. Now that FreeBSD supports
KSTAT_TYPE_RAW at least some of the functionality should
be made available.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10842
In zvol_geom_open on first open we need to guarantee
that the namespace lock is held to avoid spurious
failures in zvol_first_open.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <freqlabs@FreeBSD.org>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10841
This commit closes issues labeled with:
"Status: Feedback requested" after 1 month, if the
label is not removed or the author has not responded
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Signed-off-by: Kjeld Schouten-Lebbing <kjeld@schouten-lebbing.nl>
Closes#10807Closes#10808
Commit dcdc12e added compatibility code to treat NR_SLAB_RECLAIMABLE_B
as if it were the same as NR_SLAB_RECLAIMABLE. However, the new value
is in bytes while the old value was in pages which means they are not
interchangeable.
The only place the reclaimable slab size is used is as a component of
the calculation done by arc_free_memory(). This function returns the
amount of memory the ARC considers to be free or reclaimable at little
cost. Rather than switch to a new interface to get this value it has
been removed it from the calculation. It is normally a minor component
compared to the number of inactive or free pages, and removing it
aligns the behavior with the FreeBSD version of arc_free_memory().
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Coleman Kane <ckane@colemankane.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#10834
zfs-load-key-DATASET.service was gaining an
After=systemd-journald.socket due to its stdout/stderr going to the
journal (which is the default). systemd-journald.socket has an After
(via RequiresMountsFor=/run/systemd/journal) on -.mount. If the root
filesystem is encrypted, -.mount gets an After
zfs-load-key-DATASET.service.
By setting stdout and stderr to null on the key load services, we avoid
this loop.
Reviewed-by: Antonio Russo <antonio.e.russo@gmail.com>
Reviewed-by: InsanePrawn <insane.prawny@gmail.com>
Signed-off-by: Richard Laager <rlaager@wiktel.com>
Closes#10356Closes#10388
When generating units with zfs-mount-generator, if the pool is already
imported, zfs-import.target is not needed. This avoids a dependency
loop on root-on-ZFS systems:
systemd-random-seed.service After (via RequiresMountsFor)
var-lib.mount After
zfs-import.target After
zfs-import-{cache,scan}.service After
cryptsetup.service After
systemd-random-seed.service
Reviewed-by: Antonio Russo <antonio.e.russo@gmail.com>
Reviewed-by: InsanePrawn <insane.prawny@gmail.com>
Signed-off-by: Richard Laager <rlaager@wiktel.com>
Closes#10388
This will allow an override of auto-detection of distribution, which
is based on checking presence of /etc/*-release files.
Build systems makes a lot of file location assumptions based on
detected distribution.
Some distributions (like gentoo) may prefer explicitly
setting --with-vendor=gentoo to avoid auto-detection.
Since auto-detection checks all files in order, current script may
misdetect even on gentoo system if /etc/redhat-release file is present
Default behavior is unchanged and default is --with-vendor=check
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Georgy Yakovlev <gyakovlev@gentoo.org>
Closes#10835
If kernel is compiled with -march=znver1 or -march=znver2 zstd module
compilation will fail due to SSE register return with SSE disabled.
What's interesting, is that -march=skylake also implies -mbmi which
defines __BMI__ but compilation succeeds. It is probably due to
different BMI implementations on AMD and INTEL processors and the
way compiler uses instructions.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Georgy Yakovlev <gyakovlev@gentoo.org>
Closes#10758Closes#10829
There are a ton of zfs-* and zpool-* man pages. This adds them to
the SEE ALSO section so that people can more quickly look through
what all the options are, now that the pages have been split.
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: John-Mark Gurney <jmg@funkthat.com>
Closes#10589
Because dnode_sync_free_range() must drop dn_mtx during its processing,
using it as a callback to range_tree_vacate() is not safe. No other
operations (besides destroy) are allowed once range_tree_vacate() has
begun, and dropping dn_mtx would leave a window open for another thread
to observe that invalid (and unsafe) state via dnode_block_freed().
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Signed-off-by: Patrick Mooney <pmooney@oxide.computer>
Closes#10708Closes#10823
The zfs/sa.c source file accidentally includes sys/dnode.h twice.
Remove the second occurrence.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#10816Closes#10819
The root cause of the issue is that we only occasionally do as the
comments in the code suggest and actually ignore the %recv dataset when
it comes to filesystem limit tracking. Specifically, the only time we
ignore it is when initializing the filesystem and snapshot limit values;
when creating a new %recv dataset or deleting one, we always update
the bookkeeping. This causes a problem if you init the fs count on a
filesystem that already has a %recv dataset, since the bookmarking
will be decremented but not incremented. This is resolved in this
patch by simply always tracking the %recv dataset as a child.
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed by: Jerry Jelinek <jerry.jelinek@joyent.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#10791
By accident previous PR broke the bug report form.
This commit fixes it
(and is actually tested completely to work)
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Kjeld Schouten-Lebbing <kjeld@schouten-lebbing.nl>
Closes#10821
The #pragma ident is a historical relic and not needed any more, this
pragma is actually unknown for common compilers and is only causing
trouble.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Toomas Soome <tsoome@me.com>
Closes#10810
- Add Status: Triage Needed to bug reports
Currently "Type: Defect" is auto added.
Adding a triage tag, makes sure all issues are reviewed by a maintainer
It also opens up some options to priorities defects in the near future.
- Prevent future StaleBot Spam
StaleBot will limit itself to 6 actions per hour
This should prevent future floods of StaleBot activity
(aka Spam)
- StaleBot: Ignore issues that are being worked on
Ignore the following Issues:
- tagged: "Status: Work in Progress"
- Having a maintainer assigned
- Being part of a project
- Having a milestone tag
- Rename Ignore "Type: Understood" to "Bot: Not Stale"
This Commits changes the general ignore tag for StaleBot from:
"Type: Understood"
to
"Bot: Not Stale"
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Kjeld Schouten-Lebbing <kjeld@schouten-lebbing.nl>
Closes#10813
Since L2ARC buffers are not evicted on memory pressure, too large
amount of headers on system with irrationally large L2ARC can render
it slow or even unusable. This change limits L2ARC writes and
rebuild if unevictable L2ARC-only headers reach dangerous level.
While there, call arc_adapt() on L2ARC rebuild, so that it could
properly grow arc_c, reflecting potentially significant ARC size
increase and avoiding slow growth with hopeless eviction attempts
later when "overflow" is detected.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reported-by: Richard Elling <Richard.Elling@RichardElling.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#10765
2020-08-25 14:33:36 -07:00
1060 changed files with 62818 additions and 43607 deletions
- [ ] Performance enhancement (non-breaking change which improves efficiency)
- [ ] Code cleanup (non-breaking change which makes code smaller or more readable)
- [ ] Breaking change (fix or feature that would cause existing functionality to change)
- [ ] Library ABI change (libzfs, libzfs\_core, libnvpair, libuutil and libzfsbootenv)
- [ ] Documentation (a change to man pages or other documentation)
### Checklist:
<!--- Go over all the following points, and put an `x` in all the boxes that apply. -->
<!--- If you're unsure about any of these, don't hesitate to ask. We're here to help! -->
- [ ] My code follows the ZFS on Linux [code style requirements](https://github.com/zfsonlinux/zfs/blob/master/.github/CONTRIBUTING.md#coding-conventions).
- [ ] My code follows the OpenZFS [code style requirements](https://github.com/openzfs/zfs/blob/master/.github/CONTRIBUTING.md#coding-conventions).
- [ ] I have updated the documentation accordingly.
- [ ] I have read the [**contributing** document](https://github.com/zfsonlinux/zfs/blob/master/.github/CONTRIBUTING.md).
- [ ] I have added [tests](https://github.com/zfsonlinux/zfs/tree/master/tests) to cover my changes.
- [ ] I have read the [**contributing** document](https://github.com/openzfs/zfs/blob/master/.github/CONTRIBUTING.md).
- [ ] I have added [tests](https://github.com/openzfs/zfs/tree/master/tests) to cover my changes.
- [ ] I have run the ZFS Test Suite with this change applied.
- [ ] All commit messages are properly formatted and contain [`Signed-off-by`](https://github.com/zfsonlinux/zfs/blob/master/.github/CONTRIBUTING.md#signed-off-by).
- [ ] All commit messages are properly formatted and contain [`Signed-off-by`](https://github.com/openzfs/zfs/blob/master/.github/CONTRIBUTING.md#signed-off-by).
read -r val 2>/dev/null < "/sys/block/$device/queue/rotational"
case "$val" in
0) MEDIA="ssd" ;;
1) MEDIA="hdd" ;;
esac
if [ "$val" = "1" ]; then
MEDIA="hdd"
vpd_pg83="/sys/block/$device/device/vpd_pg83"
if [ -f "$vpd_pg83" ]; then
if grep -q --binary "iqn." "$vpd_pg83"; then
MEDIA="iscsi"
fi
fi
else
if [ -f "$VDEV_UPATH" ]; then
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
Tony Hutter