scan-build does not do cross translation unit analysis to realize that
`dmu_buf_hold()` will always set `bpo->bpo_cached_dbuf` to a non-NULL
pointer, so we add an assertion to make it realize this.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14575
Clang's static analyzer reports that if we try to rename a root dataset
in `dsl_dir_rename_sync()`, we will have a NULL pointer passed to
strlcpy(). This is impossible because `dsl_dir_rename_check()` will
prevent us from doing this. We add an assertion to silence this warning.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14575
CodeQL's cpp/constant-comparison query from its security-and-extended
query set reported 4 instances where we have comparions that always
evaluate the same way.
In `draid_config_by_type()`, we have an early `if (nparity == 0)` check
that returns `EINVAL`, making a later `if (nparity == 0 || nparity >
VDEV_DRAID_MAXPARITY)` partially redundant. The later check prints an
error message when parity is 0, but the early check does not. This is
not useful feedback, so we move the later check to the place where the
early check runs to replace the early check.
In `perform_thread_merge()`, we return when `num_threads == 0`. After
that block, we do `if (num_threads > 0) {`, which will always be true.
We remove the `if` statement.
In `sa_modify_attrs()`, we have a loop condition that is `k != 2`, but
at the end of the loop, we have `if (k == 0 && hdl->sa_spill)` followed
by an else that does a break. The result is that k != 2 will never be
evaluated when it is false. We drop the comparison.
In `zap_leaf_array_read()`, we have a for loop condition that is `i <
ZAP_LEAF_ARRAY_BYTES && len > 0`. However, that loop itself is in a loop
that is `while (len > 0)` and while the value of len is decremented
inside the loop, when `len == 0`, it will return, such that `len > 0`
inside the loop condition will always be true. We drop that part of the
condition.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14575
Clang's static analyzer reports that if a `blkid == DMU_SPILL_BLKID` is
passed, then we can have a NULL pointer dereference when either
->dn_have_spill or `DNODE_FLAG_SPILL_BLKPTR` is not set. This should not
happen. We add an `ASSERT()` to suppress reports about NULL pointer
dereferences.
Originally, I wanted to use one or two IMPLY statements on
pre-conditions before the call to `dbuf_findbp()`, but Clang's static
analyzer did not understand it.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14575
Clang's static analyzer pointed out that we can have a NULL pointer
dereference if we ever attempt to split a vdev that has only 1 child. If
that happens, we are left with zero children, but then try to access a
non-existent child. Calling vdev_split() on a vdev with only 1 child
should be impossible due to how the code is structured. If this ever
happens, it would be best to stop execution immediately even in a
production environment to allow for the best possible chance of recovery
by an expert, so we use `VERIFY3U()` instead of `ASSERT3U()`.
Unfortunately, while that defensive assertion will prevent execution
from ever reaching the NULL pointer dereference, Clang's static analyzer
does not realize that, so we add an `ASSERT()` to inform it of this.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14575
Clang's static analyzer reports a possible NULL pointer dereference in
abd_get_size() when called from vdev_draid_map_alloc_write() called from
vdev_draid_map_alloc_row() and vdc->vdc_nparity == 0. This should be
impossible, so we add an assertion to silence the defect report.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14575
Traditionally ARC adaptation was limited to MRU/MFU distribution. But
for years people with metadata-centric workload demanded mechanisms to
also manage data/metadata distribution, that in original ZFS was just
a FIFO. As result ZFS effectively got separate states for data and
metadata, minimum and maximum metadata limits etc, but it all required
manual tuning, was not adaptive and in its heart remained a bad FIFO.
This change removes most of existing eviction logic, rewriting it from
scratch. This makes MRU/MFU adaptation individual for data and meta-
data, same as the distribution between data and metadata themselves.
Since most of required states separation was already done, it only
required to make arcs_size state field specific per data/metadata.
The adaptation logic is still based on previous concept of ghost hits,
just now it balances ARC capacity between 4 states: MRU data, MRU
metadata, MFU data and MFU metadata. To simplify arc_c changes instead
of arc_p measured in bytes, this code uses 3 variable arc_meta, arc_pd
and arc_pm, representing ARC balance between metadata and data, MRU and
MFU for data, and MRU and MFU for metadata respectively as 32-bit fixed
point fractions. Since we care about the math result only when need to
evict, this moves all the logic from arc_adapt() to arc_evict(), that
reduces per-block overhead, since per-block operations are limited to
stats collection, now moved from arc_adapt() to arc_access() and using
cheaper wmsums. This also allows to remove ugly ARC_HDR_DO_ADAPT flag
from many places.
This change also removes number of metadata specific tunables, part of
which were actually not functioning correctly, since not all metadata
are equal and some (like L2ARC headers) are not really evictable.
Instead it introduced single opaque knob zfs_arc_meta_balance, tuning
ARC's reaction on ghost hits, allowing administrator give more or less
preference to metadata without setting strict limits.
Some of old code parts like arc_evict_meta() are just removed, because
since introduction of ABD ARC they really make no sense: only headers
referenced by small number of buffers are not evictable, and they are
really not evictable no matter what this code do. Instead just call
arc_prune_async() if too much metadata appear not evictable.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14359
Otherwise, we can get a deadlock that looks like this:
1. fsync() grabs spa_config_enter(zilog->zl_spa, SCL_STATE, lwb,
RW_READER) as part of zil_lwb_write_issue() . It then blocks on the
txg_sync when a flush fails from a drive power cycling.
2. The txg_sync then blocks on the pool suspending due to the loss of
too many disks.
3. zpool clear then blocks on spa_config_enter(spa, SCL_STATE |
SCL_L2ARC | SCL_ZIO, spa, RW_WRITER) because it is a writer.
The disks cannot be brought online due to fsync() holding that lock and
the user gets upset since fsync() is uninterruptibly blocked inside the
kernel.
We need to grab the lock for vdev_lookup_top(), but we do not need to
hold it while there is outstanding IO.
This fixes a regression introduced by
1ce23dcaff.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@klarasystems.com>
Sponsored-By: Wasabi Technology, Inc.
Closes#14519
The intent is that this is like ENOTSUP, but specifically for when
something can't be done because we have no support for the requested
crypto parameters; eg unlocking a dataset or receiving a stream
encrypted with a suite we don't support.
Its not intended to be recoverable without upgrading ZFS itself.
If the request could be made to work by enabling a feature or modifying
some other configuration item, then some other code should be used.
load-key: In the future we might have more crypto suites (ie new values
for the `encryption` property. Right now trying to load a key on such
a future crypto suite will look up suite parameters off the end of the
crypto table, resulting in misbehaviour and/or crashes (or, with debug
enabled, trip the assertion in `zio_crypt_key_unwrap`).
Instead, lets check the value we got from the dataset, and if we can't
handle it, abort early.
recv: When receiving a raw stream encrypted with an unknown crypto
suite, `zfs recv` would report a generic `invalid backup stream`
(EINVAL). While technically correct, its not super helpful, so lets
ship a more specific error code and message.
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Rob Norris <robn@despairlabs.com>
Closes#14577
by placing the most common use case (no special vdevs) first and avoid
allocating new variables.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#14494Closes#14563
dc5c8006f6 was recently merged to prefetch
up to 128 deadlists. Unfortunately, a loop was missing an increment,
such that it will prefetch all deadlists. The performance properties of
that patch probably should be re-evaluated.
This was caught by CodeQL's cpp/constant-comparison check in an
experimental branch where I am testing the security-and-extended
queries. It complained about the `i < 128` part of the loop condition
always evaluating to the same thing. The standard CodeQL configuration
we use missed this because it does not include that check.
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14573
The skeleton file module/icp/include/generic_impl.c can be used for
iterating over different implementations of algorithms.
It is used by SHA256, SHA512 and BLAKE3 currently.
The Solaris SHA2 implementation got replaced with a version which is
based on public domain code of cppcrypto v0.10.
These assembly files are taken from current openssl master:
- sha256-x86_64.S: x64, SSSE3, AVX, AVX2, SHA-NI (x86_64)
- sha512-x86_64.S: x64, AVX, AVX2 (x86_64)
- sha256-armv7.S: ARMv7, NEON, ARMv8-CE (arm)
- sha512-armv7.S: ARMv7, NEON (arm)
- sha256-armv8.S: ARMv7, NEON, ARMv8-CE (aarch64)
- sha512-armv8.S: ARMv7, ARMv8-CE (aarch64)
- sha256-ppc.S: Generic PPC64 LE/BE (ppc64)
- sha512-ppc.S: Generic PPC64 LE/BE (ppc64)
- sha256-p8.S: Power8 ISA Version 2.07 LE/BE (ppc64)
- sha512-p8.S: Power8 ISA Version 2.07 LE/BE (ppc64)
Tested-by: Rich Ercolani <rincebrain@gmail.com>
Tested-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tino Reichardt <milky-zfs@mcmilk.de>
Closes#13741
With some pathological access patterns it is possible to make ZFS
accumulate almost unlimited amount of speculative prefetch ZIOs.
Combined with linear ABD allocations in RAIDZ code, it appears to
be possible to exhaust system KVA, triggering kernel panic.
Address this by introducing a system-wide counter of active prefetch
requests and blocking prefetch distance doubling per stream hits if
the number of active requests is higher that ~6% of ARC size.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14516
openzfsonwindows/openzfs#206 found that it is possible to trip
`VERIFY(list_is_empty(&lwb->lwb_itxs))` when a `zil_commit()` is delayed
by the scheduler long enough for a parallel `zil_suspend()` operation to
exit `zil_commit_impl()`. This is a data race. To prevent this, we
introduce a `zilog->zl_suspend_lock` rwlock to ensure that all
outstanding `zil_commit()` operations finish before `zil_suspend()`
begins and that subsequent operations fallback to `txg_wait_synced()`
after `zil_suspend()` has begun.
On `PREEMPT_RT` Linux kernels, the `rw_enter()` implementation suffers
from writer starvation. This means that a ZIL intensive system can delay
`zil_suspend()` indefinitely. This is a pre-existing problem that
affects everything that uses rw locks, so it needs to be addressed in
the SPL. However, builds against `PREEMPT_RT` Linux kernels are
currently broken due to a GPL symbol issue (#11097), so we can safely
disregard that issue for now.
Reported-by: Arun KV <arun.kv@datacore.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14514
I forgot to remove the corresponding kmem_free() from zfs_kmod_fini() in
9a14ce43c3. Clang's static analyzer did
not complain, but the Coverity scan that was run after the patch was
merged did.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reported-by: Coverity (CID-1535275)
Closes#14556
We tripped `ASSERT(error == ENOENT || error == EEXIST || error ==
EALREADY)` in `zil_lwb_commit()` at Klara when doing robustness testing
of ZIL against drive power cycles.
That assertion presumably exists because when this code was written, the
only errors expected from here were EIO, ENOENT, EEXIST and EALREADY,
with EIO having its own handling before the assertion. However, upon
doing a manual depth first search traversal of the source tree, it turns
out that a large number of unexpected errors are possible here. In
theory, EINVAL and ENOSPC can come from dnode_hold_impl(). However, most
unexpected errors originate in the block layer and come to us from
zio_wait() in various ways. One way is ->zl_get_data() -> dmu_buf_hold()
-> dbuf_read() -> zio_wait().
From vdev_disk.c on Linux alone, zio_wait() can return the unexpected
errors ENXIO, ENOTSUP, EOPNOTSUPP, ETIMEDOUT, ENOSPC, ENOLINK,
EREMOTEIO, EBADE, ENODATA, EILSEQ and ENOMEM
This was only observed after what have been likely over 1000 test
iterations, so we do not expect to reproduce this again to find out what
the error code was. However, circumstantial evidence suggests that the
error was ENXIO.
When ENXIO or any other unexpected error occurs, the `fsync()` or
equivalent operation that called zil_commit() will return success, when
in fact, dirty data has not been committed to stable storage. This is a
violation of the Single UNIX Specification.
The code should be able to handle this and any other unknown error by
calling `txg_wait_synced()`. In addition to changing the code to call
txg_wait_synced() on unexpected errors instead of returning, we modify
it to print information about unexpected errors to dmesg.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@klarasystems.com>
Sponsored-By: Wasabi Technology, Inc.
Closes#14532
Clang's static analyzer claims that dereferencing ds in
dmu_objset_create_impl_dnstats() could cause a NULL pointer dereference
when a previous NULL check confirms that it is NULL. It is only NULL on
the MOS, for which dmu_objset_userused_enabled(os) should always return
false, so ds will never be dereferenced when it is NULL. We add an
assertion to suppress this warning.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14470
Clang's static analyzer claims that dbuf_hold_copy() will have a NULL
pointer dereference in data->b_data when called by dbuf_hold_impl().
This is impossible because data is dr->dt.dl.dr_data, which is non-NULL
whenever db->db_level == 0, which is always the case whenever
dbuf_hold_impl() calls dbuf_hold_copy(). We add an assertion to suppress
the complaint.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14470
This avoids a call to kmem_alloc() during module load. It also
suppresses a defect report from Clang's static analyzer that claims that
we will have a NULL pointer dereference in zfsdev_state_init() because
it does not understand that this has already been allocated in
zfs_kmod_init().
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14470
Clang's static analyzer points out that when IS_SA_BONUSTYPE(type) is
true and .sa_length is 0 for an attribute, we have a NULL pointer
dereference. We suppress this with an IMPLY() statement.
This was also identified by Coverity.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reported-by: Coverity (CID-1017954)
Closes#14470
Clang's static analyzer informs us of multiple NULL pointer dereferences
involving zio_checksum_error_impl().
The first is a NULL pointer dereference if bp is NULL and ci->ci_flags &
ZCHECKSUM_FLAG_EMBEDDED is false, but bp is NULL implies that
ci->ci_flags & ZCHECKSUM_FLAG_EMBEDDED is true, so we add an IMPLY()
statement to suppress the report.
The second and third are identical, and are duplicated because while the
NULL pointer dereference occurs in zio_checksum_gang_verifier(), it is
called by zio_checksum_error_impl() and there is a report for each of
the two functions. The reports state that when bp is NULL, ci->ci_flags
& ZCHECKSUM_FLAG_EMBEDDED is true and checksum is not
ZIO_CHECKSUM_LABEL, we also have a NULL pointer dereference. bp is NULL
should imply that checksum == ZIO_CHECKSUM_LABEL, so we add an IMPLY()
statement to suppress the second report. The two reports are
functionally identical.
A fourth variation of this was also reported by Coverity. It occurs when
checksum == ZIO_CHECKSUM_ZILOG2.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reported-by: Coverity (CID-1524672)
Closes#14470
Commit 34ce4c4 made zfeature_active() non-static. This is not required.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#14546
Hole detection in the zio compression code allows us to
opportunistically skip compression on holes. We can go a step further
by not doing memory allocations on holes either.
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Richard Yao <richard.yao@klarasystems.com>
Sponsored-by: Wasabi Technology, Inc.
Closes#14500
In the case of a regular compilation, the compiler
raises a warning for a dsl_deadlist_merge function, that
the stack size is to large. In debug build this can
generate an error.
Move large structures to heap.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Mariusz Zaborski <mariusz.zaborski@klarasystems.com>
Sponsored-by: Klara, Inc.
Sponsored-by: Wasabi Technology, Inc.
Closes#14524
Otherwise the dataset may be freed after the last dmu_buf_rele() leading
to a panic.
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#14522Closes#14523
Clang's static analyzer correctly identified a NULL pointer dereference
in zio_ready() when ZIO_FLAG_NODATA has been set on a zio that is
missing a block pointer. The NULL pointer dereference occurs because we
have logic intended to disable ZIO_FLAG_NODATA when it has been set on a
gang block.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14469
When dn->dn_bonus == NULL, dmu_bonus_hold_by_dnode() will unlock its
read lock on dn->dn_struct_rwlock and grab a write lock. This can be
micro-optimized by calling rw_tryupgrade().
Linux will not benefit from this since it does not support rwlock
upgrades, but FreeBSD will.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14517
With commit 34ce4c42f applied, there is no need for eee9362a7.
Revert that aside from the test. All tests introduced in those commits
pass.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#14502
spa_sync() currently grabs the write lock due to an old hack that is
documented by a comment:
We need the write lock here because, for aux vdevs,
calling vdev_config_dirty() modifies sav_config.
This is ugly and will become unnecessary when we
eliminate the aux vdev wart by integrating all vdevs
into the root vdev tree.
This has lead to deadlocks in rare edge cases from holding the write
lock. We can reduce incidence of these deadlocks by not grabbing the
write lock on pools without auxillary vdevs.
Sponsored-By: Wasabi Technology, Inc.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@klarasystems.com>
Closes#14282
Add handling to dmu_object_next for the case where *objectp == 0.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#14479
Clang's static analyzer incorrectly complains about an undefined value
here when lr->lr_common.lrc_txtype == TX_SYMLINK and txtype ==
TX_CREATE. This is impossible, because of this line:
txtype = (lr->lr_common.lrc_txtype & ~TX_CI((uint64_t)0x1 << 63));
Changing the code to compare against txtype suppresses the report.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14472
As of the 4.13 kernel filemap_range_has_page() can be used to
check if there is a page mapped in a given file range. When
available this interface should be used which eliminates the
need for the zp->z_is_mapped boolean.
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#14493
strlcat() is supposed to be given the length of the destination buffer,
including the existing contents. Unfortunately, I had been overzealous
when I wrote a51288aabb, since I gave it
the length of the destination buffer, minus the existing contents. This
likely caused a regression on large strings.
On the topic of being overzealous, the use of strlcat() in
dmu_send_estimate_fast() was unnecessary because recv_clone_name is a
fixed length string. We continue using strlcat() mostly as defensive
programming, in case the string length is ever changed, even though it
is unnecessary.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14476
The zio returned from arc_write() in dmu_objset_sync() uses
zio_nowait(). However we may reach the end of dsl_dataset_sync()
which checks if we need to activate features in the filesystem
without knowing if that zio has even run through the ZIO pipeline yet.
In that case we will flag features to be activated in
dsl_dataset_block_born() but dsl_dataset_sync() has already
completed its run and those features will not actually be activated.
Mitigate this by moving the feature activation code in
dsl_dataset_sync_done(). Also add new ASSERTs in
dsl_scan_visitbp() checking if a block contradicts any filesystem
flags.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#13816
Debugging reported NULL de-reference panic in dnode_hold_impl() I found
that for certain types of errors arc_read() may only return error code,
but not properly report it via done and pio arguments. Lack of done
calls may result in reference and/or memory leaks in higher level code.
Lack of error reporting via pio may result in unnoticed errors there.
For example, dbuf_read(), where dbuf_read_impl() ignores arc_read()
return, relies completely on the pio mechanism and missed the errors.
This patch makes arc_read() to always call done callback and always
propagate errors to parent zio, if either is provided.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14454
The PVS Studio 2016 FreeBSD kernel report stated:
\contrib\opensolaris\uts\common\fs\zfs\spa.c (1341): error V595: The 'spa->spa_spares.sav_vdevs' pointer was utilized before it was verified against nullptr. Check lines: 1341, 1342.
\sys\cddl\contrib\opensolaris\uts\common\fs\zfs\spa.c (1355): error V595: The 'spa->spa_l2cache.sav_vdevs' pointer was utilized before it was verified against nullptr. Check lines: 1355, 1357.
\sys\cddl\contrib\opensolaris\uts\common\fs\zfs\spa.c (1398): error V595: The 'spa->spa_spares.sav_vdevs' pointer was utilized before it was verified against nullptr. Check lines: 1398, 1408.
\sys\cddl\contrib\opensolaris\uts\common\fs\zfs\spa.c (1583): error V595: The 'oldvdevs' pointer was utilized before it was verified against nullptr. Check lines: 1583, 1595.
In practice, all of these uses were safe because a NULL pointer
implied a 0 vdev count, which kept us from iterating over vdevs.
However, rearranging the code to check the pointer first is not a
terrible micro-optimization and makes it more readable, so let us
do that.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14456
Encrypted blocks can not have 3 DVAs, because they use the space of the
3rd DVA for the IV+salt. zio_write_gang_block() takes this into
account, setting `gbh_copies` to no more than 2 in this case. Gang
members BP's do not have the X (encrypted) bit set (nor do they have the
DMU level and type fields set), because encryption is not handled at
this level. The gang block is reassembled, and then encryption (and
compression) are handled.
To check if this gang block is encrypted, the code in
zio_write_gang_block() checks `pio->io_bp`. This is normally fine,
because the block that's being ganged is typically the encrypted BP.
The problem is that if there is "recursive ganging", where a gang member
is itself a gang block, then when zio_write_gang_block() is called to
create a gang block for a gang member, `pio->io_bp` is the gang member's
BP, which doesn't have the X bit set, so the number of DVA's is not
restricted to 2. It should instead be looking at the the "gang leader",
i.e. the top-level gang block, to determine how many DVA's can be used,
to avoid a "NDVA's inversion" (where a child has more DVA's than its
parent).
gang leader BP: X (encrypted) bit set, 2 DVA's, IV+salt in 3rd DVA's
space:
```
DVA[0]=<1:...:100400> DVA[1]=<0:...:100400> salt=... iv=...
[L0 ZFS plain file] fletcher4 uncompressed encrypted LE
gang unique double size=100000L/100000P birth=... fill=1 cksum=...
```
leader's GBH contains a BP with gang bit set and 3 DVA's:
```
DVA[0]=<1:...:55600> DVA[1]=<0:...:55600>
[L0 unallocated] fletcher4 uncompressed unencrypted LE
contiguous unique double size=55600L/55600P birth=... fill=0 cksum=...
DVA[0]=<1:...:55600> DVA[1]=<0:...:55600>
[L0 unallocated] fletcher4 uncompressed unencrypted LE
contiguous unique double size=55600L/55600P birth=... fill=0 cksum=...
DVA[0]=<1:...:55600> DVA[1]=<0:...:55600> DVA[2]=<1:...:200>
[L0 unallocated] fletcher4 uncompressed unencrypted LE
gang unique double size=55400L/55400P birth=... fill=0 cksum=...
```
On nondebug bits, having the 3rd DVA in the gang block works for the
most part, because it's true that all 3 DVA's are available in the gang
member BP (in the GBH). However, for accounting purposes, gang block
DVA's ASIZE include all the space allocated below them, i.e. the
512-byte gang block header (GBH) as well as the gang members below that.
We see that above where the gang leader BP is 1MB logical (and after
compression: 0x`100000P`), but the ASIZE of each DVA is 2 sectors (1KB)
more than 1MB (0x`100400`).
Since thre are 3 copies of a block below it, we increment the ATIME of
the 3rd DVA of the gang leader by the space used by the 3rd DVA of the
child (1 sector, in this case). But there isn't really a 3rd DVA of the
parent; the salt is stored in place of the 3rd DVA's ASIZE.
So when zio_write_gang_member_ready() increments the parent's BP's
`DVA[2]`'s ASIZE, it's actually incrementing the parent's salt. When we
later try to read the encrypted recursively-ganged block, the salt
doesn't match what we used to write it, so MAC verification fails and we
get an EIO.
```
zio_encrypt(): encrypted 515/2/0/403 salt: 25 25 bb 9d ad d6 cd 89
zio_decrypt(): decrypting 515/2/0/403 salt: 26 25 bb 9d ad d6 cd 89
```
This commit addresses the problem by not increasing the number of copies
of the GBH beyond 2 (even for non-encrypted blocks). This simplifies
the logic while maintaining the ability to traverse all metadata
(including gang blocks) even if one copy is lost. (Note that 3 copies
of the GBH will still be created if requested, e.g. for `copies=3` or
MOS blocks.) Additionally, the code that increments the parent's DVA's
ASIZE is made to check the parent DVA's NDVAS even on nondebug bits. So
if there's a similar bug in the future, it will cause a panic when
trying to write, rather than corrupting the parent BP and causing an
error when reading.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Caused-by: #14356Closes#14440Closes#14413
When testing distributed rebuild performance with more capable
hardware it was observed than increasing the zfs_rebuild_vdev_limit
to 64M reduced the rebuild time by 17%. Beyond 64MB there was
some improvement (~2%) but it was not significant when weighed
against the increased memory usage. Memory usage is capped at 1/4
of arc_c_max.
Additionally, vr_bytes_inflight_max has been moved so it's updated
per-metaslab to allow the size to be adjust while a rebuild is
running.
Reviewed-by: Akash B <akash-b@hpe.com>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#14428
For HDD based pools the default zfs_scan_vdev_limit of 4M
per-vdev can significantly limit the maximum scrub performance.
Increasing the default to 16M can double the scrub speed from
80 MB/s per disk to 160 MB/s per disk.
This does increase the memory footprint during scrub/resilver
but given the performance win this is a reasonable trade off.
Memory usage is capped at 1/4 of arc_c_max. Note that number
of outstanding I/Os has not changed and is still limited by
zfs_vdev_scrub_max_active.
Reviewed-by: Akash B <akash-b@hpe.com>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#14428
During snapshot deletion ZFS may issue several reads for each deadlist
to merge them into next snapshot's or pool's bpobj. Number of the dead
lists increases with number of snapshots. On HDD pools it may take
significant time during which sync thread is blocked.
This patch introduces prescient prefetch of required blocks for up to
128 deadlists ahead. Tests show reduction of time required to delete
dataset with 720 snapshots with randomly overwritten file on wide HDD
pool from 75-85 to 22-28 seconds.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Issue #14276Closes#14402
When resilvering the estimated time remaining is calculated using
the average issue rate over the current pass. Where the current
pass starts when a scan was started, or restarted, if the pool
was exported/imported.
For dRAID pools in particular this can result in wildly optimistic
estimates since the issue rate will be very high while scanning
when non-degraded regions of the pool are scanned. Once repair
I/O starts being issued performance drops to a realistic number
but the estimated performance is still significantly skewed.
To address this we redefine a pass such that it starts after a
scanning phase completes so the issue rate is more reflective of
recent performance. Additionally, the zfs_scan_report_txgs
module option can be set to reset the pass statistics more often.
Reviewed-by: Akash B <akash-b@hpe.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#14410
Despite all optimizations, tests on actual hardware show that FreeBSD
kernel can't sleep for less then ~2us. Similar tests on Linux show
~50us delay at least from nanosleep() (haven't tested inside kernel).
It means that on very fast log device ZIL may not be able to satisfy
zfs_commit_timeout_pct block commit timeout, increasing log latency
more than desired.
Handle that by introduction of zil_min_commit_timeout parameter,
specifying minimal timeout value where additional delays to aggregate
writes may be skipped. Also skip delays if the LWB is more than 7/8
full, that often happens if I/O sizes are constant and match one of
LWB sizes. Both things are applied only if there were no already
outstanding log blocks, that may indicate single-threaded workload,
that by definition can not benefit from the commit delays.
While there, add short time moving average to zl_last_lwb_latency to
make it more stable.
Tests of single-threaded 4KB writes to NVDIMM SLOG on FreeBSD show IOPS
increase by 9% instead of expected 5%. For zfs_commit_timeout_pct of
1 there IOPS increase by 5.5% instead of expected 1%.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Prakash Surya <prakash.surya@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14418
If we receive a DRR_FREEOBJECTS as the first entry in an object range,
this might end up producing a hole if the freed objects were the
only existing objects in the block.
If the txg starts syncing before we've processed any following
DRR_OBJECT records, this leads to a possible race where the backing
arc_buf_t gets its psize set to 0 in the arc_write_ready() callback
while still being referenced from a dirty record in the open txg.
To prevent this, we insert a txg_wait_synced call if the first
record in the range was a DRR_FREEOBJECTS that actually
resulted in one or more freed objects.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: David Hedberg <david.hedberg@findity.com>
Sponsored by: Findity AB
Closes#11893Closes#14358
In the zstream code, Coverity reported:
"The argument could be controlled by an attacker, who could invoke the
function with arbitrary values (for example, a very high or negative
buffer size)."
It did not report this in the kernel. This is likely because the
userspace code stored this in an int before passing it into the
allocator, while the kernel code stored it in a uint32_t.
However, this did reveal a potentially real problem. On 32-bit systems
and systems with only 4GB of physical memory or less in general, it is
possible to pass a large enough value that the system will hang. Even
worse, on Linux systems, the kernel memory allocator is not able to
support allocations up to the maximum 4GB allocation size that this
allows.
This had already been limited in userspace to 64MB by
`ZFS_SENDRECV_MAX_NVLIST`, but we need a hard limit in the kernel to
protect systems. After some discussion, we settle on 256MB as a hard
upper limit. Attempting to receive a stream that requires more memory
than that will result in E2BIG being returned to user space.
Reported-by: Coverity (CID-1529836)
Reported-by: Coverity (CID-1529837)
Reported-by: Coverity (CID-1529838)
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14285
Introduce four new vdev properties:
checksum_n
checksum_t
io_n
io_t
These properties can be used for configuring the thresholds of zed's
diagnosis engine and are interpeted as <N> events in T <seconds>.
When this property is set to a non-default value on a top-level vdev,
those thresholds will also apply to its leaf vdevs. This behavior can be
overridden by explicitly setting the property on the leaf vdev.
Note that, these properties do not persist across vdev replacement. For
this reason, it is advisable to set the property on the top-level vdev
instead of the leaf vdev.
The default values for zed's diagnosis engine (10 events, 600 seconds)
remains unchanged.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Rob Wing <rob.wing@klarasystems.com>
Sponsored-by: Seagate Technology LLC
Closes#13805
In 2016, the authors of PVS Studio ran it on the FreeBSD kernel, which
identified a number of bugs / cleanup opportunities in the FreeBSD ZFS kernel
code. A few of them persist to the present day:
https://reviews.freebsd.org/D5245
Note that the scan was done against
freebsd/freebsd-src@46763fd4ca.
In particular, we have the following in free_blocks():
\sys\cddl\contrib\opensolaris\uts\common\fs\zfs\dnode_sync.c (174): error V547: Expression '__left >= __right' is always true. Unsigned type value is always >= 0.
\sys\cddl\contrib\opensolaris\uts\common\fs\zfs\dnode_sync.c (171): error V634: The priority of the '*' operation is higher than that of the '<<' operation. It's possible that parentheses should be used in the expression.
\sys\cddl\contrib\opensolaris\uts\common\fs\zfs\dnode_sync.c (175): error V547: Expression '__left >= __right' is always true. Unsigned type value is always >= 0.
A couple of assertions accidentally typecast the arguments they check to
unsigned in such a way that the result is always true. Also, parentheses
are missing around `1<<epbs` in `(db->db_blkid * 1<<epbs)`. This works
out to be okay due to multiplication not caring what order of operations
we use, but it is better to fix it to be `(db->db_blkid << epbs)`.
A few of the function local variables probably never should have been
32-bit in the first place, so we make them 64-bit. We also replace the
existing assertions with additional assertions to ensure that 64-bit
unsigned arithmetic is safe.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14407
When zfs_file_read returns error, resid may be uninitialized.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Chunwei Chen <david.chen@nutanix.com>
Closes#14404
This is only ever used with unsigned data, so the type itself should be
unsigned. Also, PVS Studio's 2016 FreeBSD kernel report correctly
identified the following assertion as always being true, so we can drop
it:
ASSERT3U(dd->dd_space_towrite[i & TXG_MASK], >=, 0);
The reason it was always true is because it would do casts to give us
unsigned comparisons. This could have been fixed by switching to
`ASSERT3S()`, but upon inspection, it turned out that this variable
never should have been allowed to be signed in the first place.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14408
Use the saved property index instead of looking it up once per DSL
directory when traversing up towards the root.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Akash B <akash-b@hpe.com>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Sponsored-by: The FreeBSD Foundation
Closes#14397
Reported-by: KMSAN
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Akash B <akash-b@hpe.com>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Sponsored-by: The FreeBSD Foundation
Closes#14397
I recently gained the ability to run Clang's static analyzer on the
linux kernel modules via a few hacks. This extended coverage to code
that was previously missed since Clang's static analyzer only looked at
code that we built in userspace. Running it against the Linux kernel
modules built from my local branch produced a total of 72 reports
against my local branch. Of those, 50 were reports of logic errors and
22 were reports of dead code. Since we already had cleaned up all of
the previous dead code reports, I felt it would be a good next step to
clean up these dead code reports. Clang did a further breakdown of the
dead code reports into:
Dead assignment 15
Dead increment 2
Dead nested assignment 5
The benefit of cleaning these up, especially in the case of dead nested
assignment, is that they can expose places where our error handling is
incorrect. A number of them were fairly straight forward. However
several were not:
In vdev_disk_physio_completion(), not only were we not using the return
value from the static function vdev_disk_dio_put(), but nothing used it,
so I changed it to return void and removed the existing (void) cast in
the other area where we call it in addition to no longer storing it to a
stack value.
In FSE_createDTable(), the function is dead code. Its helper function
FSE_freeDTable() is also dead code, as are the CPP definitions in
`module/zstd/include/zstd_compat_wrapper.h`. We just delete it all.
In zfs_zevent_wait(), we have an optimization opportunity. cv_wait_sig()
returns 0 if there are waiting signals and 1 if there are none. The
Linux SPL version literally returns `signal_pending(current) ? 0 : 1)`
and FreeBSD implements the same semantics, we can just do
`!cv_wait_sig()` in place of `signal_pending(current)` to avoid
unnecessarily calling it again.
zfs_setattr() on FreeBSD version did not have error handling issue
because the code was removed entirely from FreeBSD version. The error is
from updating the attribute directory's files. After some thought, I
decided to propapage errors on it to userspace.
In zfs_secpolicy_tmp_snapshot(), we ignore a lack of permission from the
first check in favor of checking three other permissions. I assume this
is intentional.
In zfs_create_fs(), the return value of zap_update() was not checked
despite setting an important version number. I see no backward
compatibility reason to permit failures, so we add an assertion to catch
failures. Interestingly, Linux is still using ASSERT(error == 0) from
OpenSolaris while FreeBSD has switched to the improved ASSERT0(error)
from illumos, although illumos has yet to adopt it here. ASSERT(error ==
0) was used on Linux while ASSERT0(error) was used on FreeBSD since the
entire file needs conversion and that should be the subject of
another patch.
dnode_move()'s issue was caused by us not having implemented
POINTER_IS_VALID() on Linux. We have a stub in
`include/os/linux/spl/sys/kmem_cache.h` for it, when it really should be
in `include/os/linux/spl/sys/kmem.h` to be consistent with
Illumos/OpenSolaris. FreeBSD put both `POINTER_IS_VALID()` and
`POINTER_INVALIDATE()` in `include/os/freebsd/spl/sys/kmem.h`, so we
copy what it did.
Whenever a report was in platform-specific code, I checked the FreeBSD
version to see if it also applied to FreeBSD, but it was only relevant a
few times.
Lastly, the patch that enabled Clang's static analyzer to be run on the
Linux kernel modules needs more work before it can be put into a PR. I
plan to do that in the future as part of the on-going static analysis
work that I am doing.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14380
There is an external assembly declaration extension in GNU C that glibc
uses when building with ieee128 floating point support on ppc64le.
Marking that as volatile makes no sense, so the build breaks.
It does not make sense to only mark this as volatile on Linux, since if
do not want the compiler reordering things on Linux, we do not want the
compiler reordering things on any other platform, so we stop treating
Linux specially and just manually inline the CPP macro so that we can
eliminate it. This should fix the build on ppc64le.
Tested-by: @gyakovlev
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14308Closes#14384
The Linux 5.16.14 kernel's coccicheck caught this. The semantic
patch that caught it was:
./scripts/coccinelle/null/badzero.cocci
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14372
The Linux 5.16.14 kernel's coccicheck caught this. The semantic
patch that caught it was:
./scripts/coccinelle/misc/semicolon.cocci
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14372
The Linux 5.16.14 kernel's coccicheck caught this. The semantic
patch that caught it was:
./scripts/coccinelle/misc/minmax.cocci
There was a third opportunity to use `MIN()`, but that was in
`FSE_minTableLog()` in `module/zstd/lib/compress/fse_compress.c`.
Upstream zstd has yet to make this change and I did not want to change
header includes just for MIN, or do a one off, so I left it alone.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14372
The Linux 5.16.14 kernel's coccicheck caught this. The semantic
patch that caught it was:
./scripts/coccinelle/misc/flexible_array.cocci
However, unlike the cases where the GNU zero length array extension had
been used, coccicheck would not suggest patches for the older style
single member arrays. That was good because blindly changing them would
break size calculations in most cases.
Therefore, this required care to make sure that we did not break size
calculations. In the case of `indirect_split_t`, we use
`offsetof(indirect_split_t, is_child[is->is_children])` to calculate
size. This might be subtly wrong according to an old mailing list
thread:
https://inbox.sourceware.org/gcc-prs/20021226123454.27019.qmail@sources.redhat.com/T/
That is because the C99 specification should consider the flexible array
members to start at the end of a structure, but compilers prefer to put
padding at the end. A suggestion was made to allow compilers to allocate
padding after the VLA like compilers already did:
http://std.dkuug.dk/JTC1/SC22/WG14/www/docs/n983.htm
However, upon thinking about it, whether or not we allocate end of
structure padding does not matter, so using offsetof() to calculate the
size of the structure is fine, so long as we do not mix it with sizeof()
on structures with no array members.
In the case that we mix them and padding causes offsetof(struct_t,
vla_member[0]) to differ from sizeof(struct_t), we would be doing unsafe
operations if we underallocate via `offsetof()` and then overcopy via
sizeof().
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14372
The Linux 5.16.14 kernel's coccicheck caught this. The semantic
patch that caught it was:
./scripts/coccinelle/misc/flexible_array.cocci
The Linux kernel's documentation makes a good case for why we should not
use these:
https://www.kernel.org/doc/html/latest/process/deprecated.html#zero-length-and-one-element-arrays
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14372
The Linux 5.16.14 kernel's coccicheck caught these. The semantic patch
that caught them was:
./scripts/coccinelle/api/alloc/alloc_cast.cocci
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14372
When activating filesystem features after receiving a snapshot, do
so only in syncing context.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#14304Closes#14252
The default_bs and default_ibs tunables control the default block size
and indirect block size.
So far, default_bs and default_ibs were tunable only on FreeBSD, e.g.,
sysctl vfs.zfs.default_ibs
Remove the FreeBSD-specific sysctl code and expose default_bs and
default_ibs as tunables on both Linux and FreeBSD using
ZFS_MODULE_PARAM.
One of the use cases for changing the values of those tunables is to
lower the indirect block size, which may improve performance of large
directories (as discussed during the OpenZFS Leadership Meeting
on 2022-08-16).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Mateusz Piotrowski <mateusz.piotrowski@klarasystems.com>
Sponsored-by: Wasabi Technology, Inc.
Closes#14293
This change turns `MZAP_MAX_BLKSZ` into a `ZFS_MODULE_PARAM()` called
`zap_micro_max_size`. As a result, we can experiment with different
micro ZAP sizes to improve directory size scaling.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Mateusz Piotrowski <mateuszpiotrowski@klarasystems.com>
Co-authored-by: Toomas Soome <toomas.soome@klarasystems.com>
Signed-off-by: Mateusz Piotrowski <mateuszpiotrowski@klarasystems.com>
Sponsored-by: Wasabi Technology, Inc.
Closes#14292
The Blocking Queue (bqueue) code is used by zfs send/receive to send
messages between the various threads. It uses a shared linked list,
which is locked whenever we enqueue or dequeue. For workloads which
process many blocks per second, the locking on the shared list can be
quite expensive.
This commit changes the bqueue logic to have 3 linked lists:
1. An enquing list, which is used only by the (single) enquing thread,
and thus needs no locks.
2. A shared list, with an associated lock.
3. A dequing list, which is used only by the (single) dequing thread,
and thus needs no locks.
The entire enquing list can be moved to the shared list in constant
time, and the entire shared list can be moved to the dequing list in
constant time. These operations only happen when the `fill_fraction` is
reached, or on an explicit flush request. Therefore, the lock only
needs to be acquired infrequently.
The API already allows for dequing to block until an explicit flush, so
callers don't need to be changed.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Wilson <george.wilson@delphix.com>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#14121
ECHRNG is returned when the channel program encounters a runtime
error. For example, this can happen when a snapshot doesn't exist.
We handle this error the same way as the existing EEXIST and ENOENT
error checks.
Additionally, improve the internal debug message to include the
error describing why a pool couldn't be opened.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#14351
Encrypted blocks can have up to 2 DVA's, as the third DVA is reserved
for the salt+IV. However, dmu_write_policy() allows non-encrypted
blocks (e.g. DMU_OT_OBJSET) inside encrypted datasets to request and
allocate 3 DVA's, since they don't need a salt+IV (they are merely
authenicated).
However, if such a block becomes a gang block, the gang code incorrectly
limits the gang block header to 2 DVA's. This leads to a "NDVAs
inversion", where a parent block (the gang block header) has less DVA's
than its children (the gang members), causing an assertion failure in
zio_write_gang_member_ready().
This commit addresses the problem by only restricting the gang block
header to 2 DVA's if the block is actually encrypted (and thus its gang
block members can have at most 2 DVA's).
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#14250Closes#14356
This commit supports for spare vdev hotplug. The
spare vdev associated with all the pools will be
marked as "Removed" when the drive is physically
detached and will become "Available" when the
drive is reattached. Currently, the spare vdev
status does not change on the drive removal and
the same is the case with reattachment.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#14295
Every ARC buffer holds a reference on the header. It means headers with
buffers are never evictable. When we are evicting a header, there can
be no more buffers to free. Just assert that.
b_evict_lock seems not protecting anything now. Remove it.
Buffers checksum should also be freed with the last uncompressed buffer,
so it should not be there also when we are evicting the header.
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
This saves 40 bytes per full ARC header, reducing it on FreeBSD from
240 to 200 bytes on production bits.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#14315
Previously the primarycache property was handled only in the dbuf
layer. Since the speculative prefetcher is implemented in the ARC,
it had to be disabled for uncacheable buffers.
This change gives the ARC knowledge about uncacheable buffers
via arc_read() and arc_write(). So when remove_reference() drops
the last reference on the ARC header, it can either immediately destroy
it, or if it is marked as prefetch, put it into a new arc_uncached state.
That state is scanned every second, evicting stale buffers that were
not demand read.
This change also tracks dbufs that were read from the beginning,
but not to the end. It is assumed that such buffers may receive further
reads, and so they are stored in dbuf cache. If a following
reads reaches the end of the buffer, it is immediately evicted.
Otherwise it will follow regular dbuf cache eviction. Since the dbuf
layer does not know actual file sizes, this logic is not applied to
the final buffer of a dnode.
Since uncacheable buffers should no longer stay in the ARC for long,
this patch also tries to optimize I/O by allocating ARC physical
buffers as linear to allow buffer sharing.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Wilson <george.wilson@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14243
ARC code was many times significantly modified over the years, that
created significant amount of tangled and potentially broken code.
This should make arc_access()/arc_read() code some more readable.
- Decouple prefetch status tracking from b_refcnt. It made sense
originally, but became highly cryptic over the years. Move all the
logic into arc_access(). While there, clean up and comment state
transitions in arc_access(). Some transitions were weird IMO.
- Unify arc_access() calls to arc_read() instead of sometimes calling
it from arc_read_done(). To avoid extra state changes and checks add
one more b_refcnt for ARC_FLAG_IO_IN_PROGRESS.
- Reimplement ARC_FLAG_WAIT in case of ARC_FLAG_IO_IN_PROGRESS with
the same callback mechanism to not falsely account them as hits. Count
those as "iohits", an intermediate between "hits" and "misses". While
there, call read callbacks in original request order, that should be
good for fairness and random speculations/allocations/aggregations.
- Introduce additional statistic counters for prefetch, accounting
predictive vs prescient and hits vs iohits vs misses.
- Remove hash_lock argument from functions not needing it.
- Remove ARC_FLAG_PREDICTIVE_PREFETCH, since it should be opposite
to ARC_FLAG_PRESCIENT_PREFETCH if ARC_FLAG_PREFETCH is set. We may
wish to add ARC_FLAG_PRESCIENT_PREFETCH to few more places.
- Fix few false positive tests found in the process.
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14123
There is a lock order inversion deadlock between `spa_errlog_lock` and
`dp_config_rwlock`:
A thread in `spa_delete_dataset_errlog()` is running from a sync task.
It is holding the `dp_config_rwlock` for writer (see
`dsl_sync_task_sync()`), and waiting for the `spa_errlog_lock`.
A thread in `dsl_pool_config_enter()` is holding the `spa_errlog_lock`
(see `spa_get_errlog_size()`) and waiting for the `dp_config_rwlock` (as
reader).
Note that this was introduced by #12812.
This commit address this by defining the lock ordering to be
dp_config_rwlock first, then spa_errlog_lock / spa_errlist_lock.
spa_get_errlog() and spa_get_errlog_size() can acquire the locks in this
order, and then process_error_block() and get_head_and_birth_txg() can
verify that the dp_config_rwlock is already held.
Additionally, a buffer overrun in `spa_get_errlog()` is corrected. Many
code paths didn't check if `*count` got to zero, instead continuing to
overwrite past the beginning of the userspace buffer at `uaddr`.
Tested by having some errors in the pool (via `zinject -t data
/path/to/file`), one thread running `zpool iostat 0.001`, and another
thread runs `zfs destroy` (in a loop, although it hits the first time).
This reproduces the problem easily without the fix, and works with the
fix.
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: George Amanakis <gamanakis@gmail.com>
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#14239Closes#14289
This fixes a kernel stack leak.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Tested-by: Nicholas Sherlock <n.sherlock@gmail.com>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13778Closes#14255
We currently compute a 64-bit hash three times, which consumes 0.8% CPU
time on ARC eviction heavy workloads. Caching the 64-bit value in the
dbuf allows us to avoid that overhead.
Sponsored-By: Wasabi Technology, Inc.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Richard Yao <richard.yao@klarasystems.com>
Closes#14251
If the fields to be listed and sorted by are constrained to those
populated by dsl_dataset_fast_stat(), then zfs list is much faster,
as it does not need to open each objset and reads its properties.
A previous optimization by Pawel Dawidek
(0cee24064a) took advantage
of this to make listing snapshot names sorted only by name much faster.
However, it was limited to `-o name -s name`, this work extends this
optimization to work with:
- name
- guid
- createtxg
- numclones
- inconsistent
- redacted
- origin
and could be further extended to any other properties supported by
dsl_dataset_fast_stat() or similar, that do not require extra locking
or reading from disk.
This was committed before (9a9e2e343dfa2af28bf7910de77ae73aa006de62),
but was reverted due to a regression when used with an older kernel.
If the kernel does not populate zc->zc_objset_stats, we now fallback
to getting the properties via the slower interface, to avoid problems
with newer userland and older kernels.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Closes#14110
Context:
We recently had a scenario where a customer with 2x10TB disks at 95+%
fragmentation and capacity, wanted to migrate their disks to a 2x20TB
setup. So they added the 2 new disks and submitted the removal of the
first 10TB disk. The removal took a lot more than expected (order of
more than a week to 2 weeks vs a couple of days) and once it was done it
generated a huge indirect mappign table in RAM (~16GB vs expected ~1GB).
Root-Cause:
The removal code calls `metaslab_alloc_dva()` to allocate a new block
for each evacuating block in the removing device and it tries to batch
them into 16MB segments. If it can't find such a segment it tries for
8MBs, 4MBs, all the way down to 512 bytes.
In our scenario what would happen is that `metaslab_alloc_dva()` from
the removal thread pick the new devices initially but wouldn't allocate
from them because of throttling in their metaslab allocation queue's
depth (see `metaslab_group_allocatable()`) as these devices are new and
favored for most types of allocations because of their free space. So
then the removal thread would look at the old fragmented disk for
allocations and wouldn't find any contiguous space and finally retry
with a smaller allocation size until it would to the low KB range. This
caused a lot of small mappings to be generated blowing up the size of
the indirect table. It also wasted a lot of CPU while the removal was
active making everything slow.
This patch:
Make all allocations coming from the device removal thread bypass the
throttle checks. These allocations are not even counted in the metaslab
allocation queues anyway so why check them?
Side-Fix:
Allocations with METASLAB_DONT_THROTTLE in their flags would not be
accounted at the throttle queues but they'd still abide by the
throttling rules which seems wrong. This patch fixes this by checking
for that flag in `metaslab_group_allocatable()`. I did a quick check to
see where else this flag is used and it doesn't seem like this change
would cause issues.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Closes#14159
If the bp is NULL, we have a hole. However, when we build with
assertions, we will dereference bp when `blkid == DMU_SPILL_BLKID`. When
this happens on a hole, we will have a NULL pointer dereference.
Reported-by: Coverity (CID-1524670)
Reviewed-by: Damian Szuberski <szuberskidamian@gmail.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14264
dsl_dataset_snapshot_sync_impl() declares `static zil_header_t zero_zil
__maybe_unused;`, but this is also declared globally. This wastes
memory.
CodeQL's cpp/local-variable-hides-global-variable check caught this.
Reviewed-by: Damian Szuberski <szuberskidamian@gmail.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14263
When doing a device removal on a pool with gang blocks, the zio pipeline
can deadlock when trying to free blocks from a device which is being
removed with a stack similar to this:
0xffff8ab9a13a1740 UNINTERRUPTIBLE 4
__schedule+0x2e5
__schedule+0x2e5
schedule+0x33
schedule_preempt_disabled+0xe
__mutex_lock.isra.12+0x2a7
__mutex_lock.isra.12+0x2a7
__mutex_lock_slowpath+0x13
mutex_lock+0x2c
free_from_removing_vdev+0x61
metaslab_free_impl+0xd6
metaslab_free_dva+0x5e
metaslab_free+0x196
zio_free_sync+0xe4
zio_free_gang+0x38
zio_gang_tree_issue+0x42
zio_gang_tree_issue+0xa2
zio_gang_issue+0x6d
zio_execute+0x94
zio_execute+0x94
taskq_thread+0x23b
kthread+0x120
ret_from_fork+0x1f
Since there are gang blocks we have to read the gang members as part of
the free. This can be seen with a zio dependency tree that looks like
this:
sdb> echo 0xffff900c24f8a700 | zio -rc | zio
ADDRESS TYPE STAGE WAITER
0xffff900c24f8a700 NULL CHECKSUM_VERIFY 0xffff900ddfd31740
0xffff900c24f8c920 FREE GANG_ASSEMBLE -
0xffff900d93d435a0 READ DONE
In the illustration above we are processing frees but because of gang
block we have to read the constituents blocks. Once we finish the READ
in the zio pipeline we will execute the parent. In this case the parent
is a FREE but the zio taskq is a READ and we continue to process the
pipeline leading to the stack above. In the stack above, we are blocked
waiting for the svr_lock so as a result a READ interrupt taskq thread
is now consumed. Eventually, all of the READ taskq threads end up
blocked and we're unable to complete any read requests.
In zio_notify_parent there is an optimization to continue to use
the taskq thread to exectue the parent's pipeline. To resolve the
deadlock above, we only allow this optimization if the parent's
zio type matches the child which just completed.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: George Wilson <gwilson@delphix.com>
External-issue: DLPX-80130
Closes#14236
After a device has been removed, any nopwrites for blocks on that
indirect vdev should be ignored and a new block should be allocated. The
original code attempted to handle this but used the wrong block pointer
when checking for indirect vdevs and failed to check all DVAs.
This change corrects both of these issues and modifies the test case
to ensure that it properly tests nopwrites with device removal.
Reviewed-by: Prakash Surya <prakash.surya@delphix.com>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Wilson <gwilson@delphix.com>
Closes#14235
The checksum error counter is incremented after reporting to ZED. This
leads ZED to receiving a checksum error report with 0 checksum errors.
To avoid this, bump the checksum error counter before reporting to ZED.
Sponsored-by: Seagate Technology LLC
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Wing <rob.wing@klarasystems.com>
Closes#14190
- Clang 15 doesn't support `-fno-ipa-sra` anymore. Do a separate
check for `-fno-ipa-sra` support by $KERNEL_CC.
- Don't enable `-mgeneral-regs-only` for certain module files.
Fix#13260
- Scope `GCC diagnostic ignored` statements to GCC only. Clang
doesn't need them to compile the code.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: szubersk <szuberskidamian@gmail.com>
Closes#13260Closes#14150
When ZFS is built with assertions, a prefetch is done on a redacted
blkptr and `dpa->dpa_dnode` is NULL, we will have a NULL pointer
dereference in `dbuf_prefetch_indirect_done()`.
Both Coverity and Clang's Static Analyzer caught this.
Reported-by: Coverity (CID 1524671)
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14210
range is always deferenced before it reaches this check, such that the
kmem_zalloc() call is never executed.
A previously version of this had erronously also pruned the
`range->eos_marker = B_TRUE` line, but it must be set whenever we
encounter an error or are cancelled early.
Coverity incorrectly complained about a potential NULL pointer
dereference because of this.
Reported-by: Coverity (CID 1524550)
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14210
There was the series from me a year ago which fixed most of the
callback vs implementation prototype mismatches. It was based on
running the CFI-enabled kernel (in permissive mode -- warning
instead of panic) and performing a full ZTS cycle, and then fixing
all of the problems caught by CFI.
Now, Clang 16-dev has new warning flag, -Wcast-function-type-strict,
which detect such mismatches at compile-time. It allows to find the
remaining issues missed by the first series.
There are only two of them left: one for the
secpolicy_vnode_setattr() callback and one for taskq_dispatch().
The fix is easy, since they are not used anywhere else.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Closes#14207
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#14199
I've noticed that some of those counters are used in hot paths like
dnode_hold_impl(), and results of this change is visible in profiler.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#14198
atomic_dec_32() should be a bit lighter than atomic_dec_32_nv().
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#14200
If the attached disk already contains a vdev GUID, it
means the disk is not clean. In such a scenario, the
physical path would be a match that makes the disk
faulted when trying to online it. So, we would only
want to proceed if either GUID matches with the last
attached disk or the disk is in a clean state.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#14181
These `sprintf()` calls are used repeatedly to write to a buffer. There
is no protection against overflow other than reviewers explicitly
checking to see if the buffers are big enough. However, such issues are
easily missed during review and when they are missed, we would rather
stop printing rather than have a buffer overflow, so we convert these
functions to use `kmem_scnprintf()`. The Linux kernel provides an entire
page for module parameters, so we are safe to write up to PAGE_SIZE.
Removing `sprintf()` from these functions removes the last instances of
`sprintf()` usage in our platform-independent kernel code. This improves
XNU kernel compatibility because the XNU kernel does not support
(removed support for?) `sprintf()`.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14209
In order for zed to process the removal event correctly,
udev change event needs to be posted to sync the blkid
information. spa_create() and spa_config_update() posts
the event already through spa_write_cachefile(). Doing
the same for spa_vdev_attach() that handles the case
for vdev attachment and replacement.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#14172
We are not allowed to dirty a filesystem when done receiving
a snapshot. In this case the flag SPA_FEATURE_LARGE_BLOCKS will
not be set on that filesystem since the filesystem is not on
dp_dirty_datasets, and a subsequent encrypted raw send will fail.
Fix this by checking in dsl_dataset_snapshot_sync_impl() if the feature
needs to be activated and do so if appropriate.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#13699Closes#13782
In #13709, as in #11294 before it, it turns out that 63a26454 still had
the same failure mode as when it was first landed as d1d47691, and
fails to unlock certain datasets that formerly worked.
Rather than reverting it again, let's add handling to just throw out
the accounting metadata that failed to unlock when that happens, as
well as a test with a pre-broken pool image to ensure that we never get
bitten by this again.
Fixes: #13709
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
The original ARC paper called for an initial 50/50 MRU/MFU split
and this is accounted in various places where arc_p = arc_c >> 1,
with further adjustment based on ghost lists size/hit. However, in
current code both arc_adapt() and arc_get_data_impl() aggressively
grow arc_p until arc_c is reached, causing unneeded pressure on
MFU and greatly reducing its scan-resistance until ghost list
adjustments kick in.
This patch restores the original behavior of initially having arc_p
as 1/2 of total ARC, without preventing MRU to use up to 100% total
ARC when MFU is empty.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Gionatan Danti <g.danti@assyoma.it>
Closes#14137Closes#14120
945b407486 neglected to `NULL` check
`tx->tx_objset`, which is already done in the function. This upset
Coverity, which complained about a "dereference after null check".
Upon inspection, it was found that whenever `dmu_tx_create_dd()` is
called followed by `dmu_tx_assign()`, such as in
`dsl_sync_task_common()`, `tx->tx_objset` will be `NULL`.
Reported-by: Coverity (CID 1527261)
Reviewed-by: Mariusz Zaborski <mariusz.zaborski@klarasystems.com>
Reviewed-by: Youzhong Yang <yyang@mathworks.com>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14170
Linux defaults to setting "failfast" on BIOs, so that the OS will not
retry IOs that fail, and instead report the error to ZFS.
In some cases, such as errors reported by the HBA driver, not
the device itself, we would wish to retry rather than generating
vdev errors in ZFS. This new property allows that.
This introduces a per vdev option to disable the failfast option.
This also introduces a global module parameter to define the failfast
mask value.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Mariusz Zaborski <mariusz.zaborski@klarasystems.com>
Sponsored-by: Seagate Technology LLC
Submitted-by: Klara, Inc.
Closes#14056
The quota for ZVOLs is set to the size of the volume. When the quota
reaches the maximum, there isn't an excellent way to check if the new
writers are overwriting the data or if they are inserting a new one.
Because of that, when we reach the maximum quota, we wait till txg is
flushed. This is causing a significant fluctuation in bandwidth.
In the case of ZVOL, the quota is enforced by the volsize, so we
can omit it.
This commit adds a sysctl thats allow to control if the quota mechanism
should be enforced or not.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Mariusz Zaborski <mariusz.zaborski@klarasystems.com>
Sponsored-by: Zededa Inc.
Sponsored-by: Klara Inc.
Closes#13838
If there were no zil entries to replay, skip zil_close. zil_close waits
for a transaction to sync. That can take several seconds, for example
during pool import of a resilvering pool. Skipping zil_close can cut
the time for "zpool import" from 2 hours to 45 seconds on a resilvering
pool with a thousand zvols.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Sponsored-by: Axcient
Closes#13999Closes#14015
Linux 5.17 commit torvalds/linux@5dfbfe71e enables "the idmapping
infrastructure to support idmapped mounts of filesystems mounted
with an idmapping". Update the OpenZFS accordingly to improve the
idmapped mount support.
This pull request contains the following changes:
- xattr setter functions are fixed to take mnt_ns argument. Without
this, cp -p would fail for an idmapped mount in a user namespace.
- idmap_util is enhanced/fixed for its use in a user ns context.
- One test case added to test idmapped mount in a user ns.
Reviewed-by: Christian Brauner <christian@brauner.io>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Youzhong Yang <yyang@mathworks.com>
Closes#14097
Special vdevs should not be replaced by a hot spare.
Log vdevs already support this, extending the
functionality for special vdevs.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#14129
Clang-16 detects this set-but-unused variable which is assigned and
incremented, but never referenced otherwise.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Brooks Davis <brooks.davis@sri.com>
Closes#14125
* The complaint in ztest_replay_write() is only possible if something
went horribly wrong. An assertion will silence this and if it goes
off, we will know that something is wrong.
* The complaint in spa_estimate_metaslabs_to_flush() is not impossible,
but seems very unlikely. We resolve this by passing the value from
the `MIN()` that does not go to infinity when the variable is zero.
There was a third report from Clang's scan-build, but that was a
definite false positive and disappeared when checked again through
Clang's static analyzer with Z3 refution via CodeChecker.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14124
Commit 68ddc06b61 introduced support
for receiving unencrypted datasets as children of encrypted ones but
unfortunately got the logic upside down. This resulted in failing to
deny receives of incremental sends into encrypted datasets without
their keys loaded. If receiving a filesystem, the receive was done
into a newly created unencrypted child dataset of the target. In
case of volumes the receive made the target volume undeletable since
a dataset was created below it, which we obviously can't handle.
Incremental streams with embedded blocks are affected as well.
We fix the broken logic to properly deny receives in such cases.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Attila Fülöp <attila@fueloep.org>
Closes#13598Closes#14055Closes#14119
Cast the integer type to (u)intptr_t before casting to "void *". In
CHERI C/C++ we warn on bare casts from integers to pointers to catch
attempts to create pointers our of thin air. We allow the warning to be
supressed with a suitable cast through (u)intptr_t.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Brooks Davis <brooks.davis@sri.com>
Closes#14131
Avoid assuming than a uint64_t can hold a pointer and reduce the
number of casts in the process.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Brooks Davis <brooks.davis@sri.com>
Closes#14131
Rather than panic debug builds when we fail to parse a whole ZIL, let's
instead improve the logging of errors and continue like in a release
build.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#14116
Check for cr == NULL before dereferencing it in
dsl_enforce_ds_ss_limits() to lookup the zone/jail ID.
Reported-by: Coverity (CID 1210459)
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Closes#14103
`snprintf()` is meant to protect against buffer overflows, but operating
on the buffer using its return value, possibly by calling it again, can
cause a buffer overflow, because it will return how many characters it
would have written if it had enough space even when it did not. In a
number of places, we repeatedly call snprintf() by successively
incrementing a buffer offset and decrementing a buffer length, by its
return value. This is a potentially unsafe usage of `snprintf()`
whenever the buffer length is reached. CodeQL complained about this.
To fix this, we introduce `kmem_scnprintf()`, which will return 0 when
the buffer is zero or the number of written characters, minus 1 to
exclude the NULL character, when the buffer was too small. In all other
cases, it behaves like snprintf(). The name is inspired by the Linux and
XNU kernels' `scnprintf()`. The implementation was written before I
thought to look at `scnprintf()` and had a good name for it, but it
turned out to have identical semantics to the Linux kernel version.
That lead to the name, `kmem_scnprintf()`.
CodeQL only catches this issue in loops, so repeated use of snprintf()
outside of a loop was not caught. As a result, a thorough audit of the
codebase was done to examine all instances of `snprintf()` usage for
potential problems and a few were caught. Fixes for them are included in
this patch.
Unfortunately, ZED is one of the places where `snprintf()` is
potentially used incorrectly. Since using `kmem_scnprintf()` in it would
require changing how it is linked, we modify its usage to make it safe,
no matter what buffer length is used. In addition, there was a bug in
the use of the return value where the NULL format character was not
being written by pwrite(). That has been fixed.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14098
CodeQL reported that when the VERIFY3U condition is false, we do not
pass enough arguments to `spl_panic()`. This is because the format
string from `snprintf()` was concatenated into the format string for
`spl_panic()`, which causes us to have an unexpected format specifier.
A CodeQL developer suggested fixing the macro to have a `%s` format
string that takes a stringified RIGHT argument, which would fix this.
However, upon inspection, the VERIFY3U check was never necessary in the
first place, so we remove it in favor of just calling `snprintf()`.
Lastly, it is interesting that every other static analyzer run on the
codebase did not catch this, including some that made an effort to catch
such things. Presumably, all of them relied on header annotations, which
we have not yet done on `spl_panic()`. CodeQL apparently is able to
track the flow of arguments on their way to annotated functions, which
llowed it to catch this when others did not. A future patch that I have
in development should annotate `spl_panic()`, so the others will catch
this too.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14098
This reverts commit fb823de9f due to a regression. It is in fact possible
for the range->eos_marker to be false on error.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #14042Closes#14104
This patch relax the quota limitation for dataset by around 3%.
What this means is that user can write more data then the quota is
set to. However thanks to that we can get more stable bandwidth, in
case when we are overwriting data in-place, and not consuming any
additional space.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Mariusz Zaborski <oshogbo@vexillium.org>
Sponsored-by: Zededa Inc.
Sponsored-by: Klara Inc.
Closes#13839
Reclaim metadata when arc_available_memory < 0 even if
meta_used is not bigger than arc_meta_limit.
As described in https://github.com/openzfs/zfs/issues/14054 if
zfs_arc_meta_limit_percent=100 then ARC target can collapse to
arc_min due to arc_purge not freeing any metadata.
This patch lets arc_prune to do its work when arc_available_memory
is negative even if meta_used is not bigger than arc_meta_limit,
avoiding ARC target collapse.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Gionatan Danti <g.danti@assyoma.it>
Closes#14054Closes#14093
The autotrim thread only reads zfs_trim_extent_bytes_min and
zfs_trim_extent_bytes_max variable only on thread start. We
should check for parameter changes during thread execution to
allow parameter changes take effect without needing to disable
then restart the autotrim.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Václav Skála <skala@vshosting.cz>
Closes#14077
Implement support for Linux's RENAME_* flags (for renameat2). Aside from
being quite useful for userspace (providing race-free ways to exchange
paths and implement mv --no-clobber), they are used by overlayfs and are
thus required in order to use overlayfs-on-ZFS.
In order for us to represent the new renameat2(2) flags in the ZIL, we
create two new transaction types for the two flags which need
transactional-level support (RENAME_EXCHANGE and RENAME_WHITEOUT).
RENAME_NOREPLACE does not need any ZIL support because we know that if
the operation succeeded before creating the ZIL entry, there was no file
to be clobbered and thus it can be treated as a regular TX_RENAME.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Pavel Snajdr <snajpa@snajpa.net>
Signed-off-by: Aleksa Sarai <cyphar@cyphar.com>
Closes#12209Closes#14070
This fixes the instances of the "Multiplication result converted to
larger type" alert that codeQL scanning found.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Andrew Innes <andrew.c12@gmail.com>
Closes#14094
We ran out of space in enum zio_flag for additional flags. Rather than
introduce enum zio_flag2 and then modify a bunch of functions to take a
second flags variable, we expand the type to 64 bits via `typedef
uint64_t zio_flag_t`.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@klarasystems.com>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Co-authored-by: Richard Yao <richard.yao@klarasystems.com>
Closes#14086
Microzap on-disk format does not include a hash tree, expecting one to
be built in RAM during mzap_open(). The built tree is linked to DMU
user buffer, freed when original DMU buffer is dropped from cache. I've
found that workloads accessing many large directories and having active
eviction from DMU cache spend significant amount of time building and
then destroying the trees. I've also found that for each 64 byte mzap
element additional 64 byte tree element is allocated, that is a waste
of memory and CPU caches.
Improve memory efficiency of the hash tree by switching from AVL-tree
to B-tree. It allows to save 24 bytes per element just on pointers.
Save 32 bits on mze_hash by storing only upper 32 bits since lower 32
bits are always zero for microzaps. Save 16 bits on mze_chunkid, since
microzap can never have so many elements. Respectively with the 16 bits
there can be no more than 16 bits of collision differentiators. As
result, struct mzap_ent now drops from 48 (rounded to 64) to 8 bytes.
Tune B-trees for small data. Reduce BTREE_CORE_ELEMS from 128 to 126
to allow struct zfs_btree_core in case of 8 byte elements to pack into
2KB instead of 4KB. Aside of the microzaps it should also help 32bit
range trees. Allow custom B-tree leaf size to reduce memmove() time.
Split zap_name_alloc() into zap_name_alloc() and zap_name_init_str().
It allows to not waste time allocating/freeing memory when processing
multiple names in a loop during mzap_open().
Together on a pool with 10K directories of 1800 files each and DMU
cache limited to 128MB this reduces time of `find . -name zzz` by 41%
from 7.63s to 4.47s, and saves additional ~30% of CPU time on the DMU
cache reclamation.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14039
a6ccb36b94 had been intended to include
this to silence Coverity reports, but this one was missed by mistake.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14043
Calling zfs_refcount_remove_many() after freeing memory means we pass a
reference to freed memory as the holder. This is not believed to be able
to cause a problem, but there is a bit of a tradition of fixing these
issues when they appear so that they do not obscure more serious issues
in static analyzer output, so we fix this one too.
Clang's static analyzer found this with the help of CodeChecker's CTU
analysis.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14043
Both Coverity and Clang's static analyzer complain about reading an
uninitialized intval if the property is not passed as DATA_TYPE_UINT64
in the nvlist. This is impossible becuase spa_prop_validate() already
checked this, but they are unlikely to be the last static analyzers to
complain about this, so lets just refactor the code to suppress the
warnings.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14043
Currently, additional/extra copies are created for metadata in
addition to the redundancy provided by the pool(mirror/raidz/draid),
due to this 2 times more space is utilized per inode and this decreases
the total number of inodes that can be created in the filesystem. By
setting redundant_metadata to none, no additional copies of metadata
are created, hence can reduce the space consumed by the additional
metadata copies and increase the total number of inodes that can be
created in the filesystem. Additionally, this can improve file create
performance due to the reduced amount of metadata which needs
to be written.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Dipak Ghosh <dipak.ghosh@hpe.com>
Signed-off-by: Akash B <akash-b@hpe.com>
Closes#13680
This patch handles the race condition on simultaneous failure of
2 drives, which misses the vdev_rebuild_reset_wanted signal in
vdev_rebuild_thread. We retry to catch this inside the
vdev_rebuild_complete_sync function.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Dipak Ghosh <dipak.ghosh@hpe.com>
Reviewed-by: Akash B <akash-b@hpe.com>
Signed-off-by: Samuel Wycliffe J <samwyc@hpe.com>
Closes#14041Closes#14050
Adds support for idmapped mounts. Supported as of Linux 5.12 this
functionality allows user and group IDs to be remapped without changing
their state on disk. This can be useful for portable home directories
and a variety of container related use cases.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Youzhong Yang <yyang@mathworks.com>
Closes#12923Closes#13671
If we encounter an EXDEV error when using the redacted snapshots
feature, the memory used by dspp.fromredactsnaps is leaked.
Clang's static analyzer caught this during an experiment in which I had
annotated various headers in an attempt to improve the results of static
analysis.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13973
The pointer is to a structure member, so it is never NULL.
Coverity complained about this.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14042
range is always deferenced before it reaches this check, such that the
kmem_zalloc() call is never executed.
There is also no need to set `range->eos_marker = B_TRUE` because it is
already set.
Coverity incorrectly complained about a potential NULL pointer
dereference because of this.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14042
It is never NULL because we return early if dsl_pool_hold() fails.
This caused Coverity to complain.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14042
This is a circularly linked list. mg->mg_next can never be NULL.
This caused 3 defect reports in Coverity.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14042
Calling spa_open() will pass a NULL pointer to spa_open_common()'s
config parameter. Under the right circumstances, we will dereference the
config parameter without doing a NULL check.
Clang's static analyzer found this.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14044
Clang's static analyzer pointed out that whenever zap_lookup_by_dnode()
is called, we have the following stack where strlcpy() is passed a NULL
pointer for realname from zap_lookup_by_dnode():
strlcpy()
zap_lookup_impl()
zap_lookup_norm_by_dnode()
zap_lookup_by_dnode()
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14044
clang-tidy caught this.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14044
This patch inserts the `static` keyword to non-global variables,
which where found by the analysis tool smatch.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tino Reichardt <milky-zfs@mcmilk.de>
Closes#13970
These were categorized as the following:
* Dead assignment 23
* Dead increment 4
* Dead initialization 6
* Dead nested assignment 18
Most of these are harmless, but since actual issues can hide among them,
we correct them.
That said, there were a few return values that were being ignored that
appeared to merit some correction:
* `destroy_callback()` in `cmd/zfs/zfs_main.c` ignored the error from
`destroy_batched()`. We handle it by returning -1 if there is an
error.
* `zfs_do_upgrade()` in `cmd/zfs/zfs_main.c` ignored the error from
`zfs_for_each()`. We handle it by doing a binary OR of the error
value from the subsequent `zfs_for_each()` call to the existing
value. This is how errors are mostly handled inside `zfs_for_each()`.
The error value here is passed to exit from the zfs command, so doing
a binary or on it is better than what we did previously.
* `get_zap_prop()` in `module/zfs/zcp_get.c` ignored the error from
`dsl_prop_get_ds()` when the property is not of type string. We
return an error when it does. There is a small concern that the
`zfs_get_temporary_prop()` call would handle things, but in the case
that it does not, we would be pushing an uninitialized numval onto
the lua stack. It is expected that `dsl_prop_get_ds()` will succeed
anytime that `zfs_get_temporary_prop()` does, so that not giving it a
chance to fix things is not a problem.
* `draid_merge_impl()` in `tests/zfs-tests/cmd/draid.c` used
`nvlist_add_nvlist()` twice in ways in which errors are expected to
be impossible, so we switch to `fnvlist_add_nvlist()`.
A few notable ones did not merit use of the return value, so we
suppressed it with `(void)`:
* `write_free_diffs()` in `lib/libzfs/libzfs_diff.c` ignored the error
value from `describe_free()`. A look through the commit history
revealed that this was intentional.
* `arc_evict_hdr()` in `module/zfs/arc.c` did not need to use the
returned handle from `arc_hdr_realloc()` because it is already
referenced in lists.
* `spa_vdev_detach()` in `module/zfs/spa.c` has a comment explicitly
saying not to use the error from `vdev_label_init()` because whatever
causes the error could be the reason why a detach is being done.
Unfortunately, I am not presently able to analyze the kernel modules
with Clang's static analyzer, so I could have missed some cases of this.
In cases where reports were present in code that is duplicated between
Linux and FreeBSD, I made a conscious effort to fix the FreeBSD version
too.
After this commit is merged, regressions like dee8934 should become
extremely obvious with Clang's static analyzer since a regression would
appear in the results as the only instance of unused code. That assumes
that Coverity does not catch the issue first.
My local branch with fixes from all of my outstanding non-draft pull
requests shows 118 reports from Clang's static anlayzer after this
patch. That is down by 51 from 169.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Cedric Berger <cedric@precidata.com>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13986
Various module parameters such as `zfs_arc_max` were originally
`uint64_t` on OpenSolaris/Illumos, but were changed to `unsigned long`
for Linux compatibility because Linux's kernel default module parameter
implementation did not support 64-bit types on 32-bit platforms. This
caused problems when porting OpenZFS to Windows because its LLP64 memory
model made `unsigned long` a 32-bit type on 64-bit, which created the
undesireable situation that parameters that should accept 64-bit values
could not on 64-bit Windows.
Upon inspection, it turns out that the Linux kernel module parameter
interface is extensible, such that we are allowed to define our own
types. Rather than maintaining the original type change via hacks to to
continue shrinking module parameters on 32-bit Linux, we implement
support for 64-bit module parameters on Linux.
After doing a review of all 64-bit kernel parameters (found via the man
page and also proposed changes by Andrew Innes), the kernel module
parameters fell into a few groups:
Parameters that were originally 64-bit on Illumos:
* dbuf_cache_max_bytes
* dbuf_metadata_cache_max_bytes
* l2arc_feed_min_ms
* l2arc_feed_secs
* l2arc_headroom
* l2arc_headroom_boost
* l2arc_write_boost
* l2arc_write_max
* metaslab_aliquot
* metaslab_force_ganging
* zfetch_array_rd_sz
* zfs_arc_max
* zfs_arc_meta_limit
* zfs_arc_meta_min
* zfs_arc_min
* zfs_async_block_max_blocks
* zfs_condense_max_obsolete_bytes
* zfs_condense_min_mapping_bytes
* zfs_deadman_checktime_ms
* zfs_deadman_synctime_ms
* zfs_initialize_chunk_size
* zfs_initialize_value
* zfs_lua_max_instrlimit
* zfs_lua_max_memlimit
* zil_slog_bulk
Parameters that were originally 32-bit on Illumos:
* zfs_per_txg_dirty_frees_percent
Parameters that were originally `ssize_t` on Illumos:
* zfs_immediate_write_sz
Note that `ssize_t` is `int32_t` on 32-bit and `int64_t` on 64-bit. It
has been upgraded to 64-bit.
Parameters that were `long`/`unsigned long` because of Linux/FreeBSD
influence:
* l2arc_rebuild_blocks_min_l2size
* zfs_key_max_salt_uses
* zfs_max_log_walking
* zfs_max_logsm_summary_length
* zfs_metaslab_max_size_cache_sec
* zfs_min_metaslabs_to_flush
* zfs_multihost_interval
* zfs_unflushed_log_block_max
* zfs_unflushed_log_block_min
* zfs_unflushed_log_block_pct
* zfs_unflushed_max_mem_amt
* zfs_unflushed_max_mem_ppm
New parameters that do not exist in Illumos:
* l2arc_trim_ahead
* vdev_file_logical_ashift
* vdev_file_physical_ashift
* zfs_arc_dnode_limit
* zfs_arc_dnode_limit_percent
* zfs_arc_dnode_reduce_percent
* zfs_arc_meta_limit_percent
* zfs_arc_sys_free
* zfs_deadman_ziotime_ms
* zfs_delete_blocks
* zfs_history_output_max
* zfs_livelist_max_entries
* zfs_max_async_dedup_frees
* zfs_max_nvlist_src_size
* zfs_rebuild_max_segment
* zfs_rebuild_vdev_limit
* zfs_unflushed_log_txg_max
* zfs_vdev_max_auto_ashift
* zfs_vdev_min_auto_ashift
* zfs_vnops_read_chunk_size
* zvol_max_discard_blocks
Rather than clutter the lists with commentary, the module parameters
that need comments are repeated below.
A few parameters were defined in Linux/FreeBSD specific code, where the
use of ulong/long is not an issue for portability, so we leave them
alone:
* zfs_delete_blocks
* zfs_key_max_salt_uses
* zvol_max_discard_blocks
The documentation for a few parameters was found to be incorrect:
* zfs_deadman_checktime_ms - incorrectly documented as int
* zfs_delete_blocks - not documented as Linux only
* zfs_history_output_max - incorrectly documented as int
* zfs_vnops_read_chunk_size - incorrectly documented as long
* zvol_max_discard_blocks - incorrectly documented as ulong
The documentation for these has been fixed, alongside the changes to
document the switch to fixed width types.
In addition, several kernel module parameters were percentages or held
ashift values, so being 64-bit never made sense for them. They have been
downgraded to 32-bit:
* vdev_file_logical_ashift
* vdev_file_physical_ashift
* zfs_arc_dnode_limit_percent
* zfs_arc_dnode_reduce_percent
* zfs_arc_meta_limit_percent
* zfs_per_txg_dirty_frees_percent
* zfs_unflushed_log_block_pct
* zfs_vdev_max_auto_ashift
* zfs_vdev_min_auto_ashift
Of special note are `zfs_vdev_max_auto_ashift` and
`zfs_vdev_min_auto_ashift`, which were already defined as `uint64_t`,
and passed to the kernel as `ulong`. This is inherently buggy on big
endian 32-bit Linux, since the values would not be written to the
correct locations. 32-bit FreeBSD was unaffected because its sysctl code
correctly treated this as a `uint64_t`.
Lastly, a code comment suggests that `zfs_arc_sys_free` is
Linux-specific, but there is nothing to indicate to me that it is
Linux-specific. Nothing was done about that.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Original-patch-by: Andrew Innes <andrew.c12@gmail.com>
Original-patch-by: Jorgen Lundman <lundman@lundman.net>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13984Closes#14004
Coverity complains about possible bugs involving referencing NULL return
values and division by zero. The division by zero bugs require that a
block pointer be corrupt, either from in-memory corruption, or on-disk
corruption. The NULL return value complaints are only bugs if
assumptions that we make about the state of data structures are wrong.
Some seem impossible to be wrong and thus are false positives, while
others are hard to analyze.
Rather than dismiss these as false positives by assuming we know better,
we add defensive assertions to let us know when our assumptions are
wrong.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13972
= Problem
While examining a customer's system we noticed unreasonable space
usage from a few snapshots due to gang blocks. Under some further
analysis we discovered that the pool would create gang blocks because
all its disks had non-zero write error counts and they'd be skipped
for normal metaslab allocations due to the following if-clause in
`metaslab_alloc_dva()`:
```
/*
* Avoid writing single-copy data to a failing,
* non-redundant vdev, unless we've already tried all
* other vdevs.
*/
if ((vd->vdev_stat.vs_write_errors > 0 ||
vd->vdev_state < VDEV_STATE_HEALTHY) &&
d == 0 && !try_hard && vd->vdev_children == 0) {
metaslab_trace_add(zal, mg, NULL, psize, d,
TRACE_VDEV_ERROR, allocator);
goto next;
}
```
= Proposed Solution
Get rid of the predicate in the if-clause that checks the past
write errors of the selected vdev. We still try to allocate from
HEALTHY vdevs anyway by checking vdev_state so the past write
errors doesn't seem to help us (quite the opposite - it can cause
issues in long-lived pools like the one from our customer).
= Testing
I first created a pool with 3 vdevs:
```
$ zpool list -v volpool
NAME SIZE ALLOC FREE
volpool 22.5G 117M 22.4G
xvdb 7.99G 40.2M 7.46G
xvdc 7.99G 39.1M 7.46G
xvdd 7.99G 37.8M 7.46G
```
And used `zinject` like so with each one of them:
```
$ sudo zinject -d xvdb -e io -T write -f 0.1 volpool
```
And got the vdevs to the following state:
```
$ zpool status volpool
pool: volpool
state: ONLINE
status: One or more devices has experienced an unrecoverable error.
...<cropped>..
action: Determine if the device needs to be replaced, and clear the
...<cropped>..
config:
NAME STATE READ WRITE CKSUM
volpool ONLINE 0 0 0
xvdb ONLINE 0 1 0
xvdc ONLINE 0 1 0
xvdd ONLINE 0 4 0
```
I also double-checked their write error counters with sdb:
```
sdb> spa volpool | vdev | member vdev_stat.vs_write_errors
(uint64_t)0 # <---- this is the root vdev
(uint64_t)2
(uint64_t)1
(uint64_t)1
```
Then I checked that I the problem was reproduced in my VM as I the
gang count was growing in zdb as I was writting more data:
```
$ sudo zdb volpool | grep gang
ganged count: 1384
$ sudo zdb volpool | grep gang
ganged count: 1393
$ sudo zdb volpool | grep gang
ganged count: 1402
$ sudo zdb volpool | grep gang
ganged count: 1414
```
Then I updated my bits with this patch and the gang count stayed the
same.
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Closes#14003
If no errors are encountered, we read an uninitialized error value.
Clang's static analyzer complained about this.
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14007
The metaslab_check_free() function only needs to be called in the
GANG|DEDUP|etc case because zio_free_sync() will internally call
metaslab_check_free().
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Finix1979 <yancw@info2soft.com>
Closes#13977
If the `list_head()` returns NULL, we dereference it, right before we
check to see if it returned NULL.
We have defined two different pointers that both point to the same
thing, which are `origin_head` and `origin_ds`. Almost everything uses
`origin_ds`, so we switch them to use `origin_ds`.
We also promote `origin_ds` to a const pointer so that the compiler
verifies that nothing modifies it.
Coverity complained about this.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Neal Gompa <ngompa@datto.com>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13967
Some header files define structures like this one:
typedef const struct zio_checksum_info {
/* ... */
const char *ci_name;
} zio_abd_checksum_func_t;
So we can use `zio_abd_checksum_func_t` for const declarations now.
It's not needed that we use the `const` qualifier again like this:
`const zio_abd_checksum_func_t *varname;`
This patch solves the double const qualifiers, which were found by
smatch.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Tino Reichardt <milky-zfs@mcmilk.de>
Closes#13961
= Issue
Recently we hit an assertion panic in `dsl_process_sub_livelist` while
exporting the spa and interrupting `bpobj_iterate_nofree`. In that case
`bpobj_iterate_nofree` stops mid-way returning an EINTR without clearing
the intermediate AVL tree that keeps track of the livelist entries it
has encountered so far. At that point the code has a VERIFY for the
number of elements of the AVL expecting it to be zero (which is not the
case for EINTR).
= Fix
Cleanup any intermediate state before destroying the AVL when
encountering EINTR. Also added a comment documenting the scenario where
the EINTR comes up. There is no need to do anything else for the calles
of `dsl_process_sub_livelist` as they already handle the EINTR case.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Closes#13939
2a493a4c71 was intended to fix all
instances of coverity reported unchecked return values, but
unfortunately, two were missed by mistake. This commit fixes the
unchecked return values that had been missed.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Neal Gompa <ngompa@datto.com>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13945
ZED does not take any action for disk removal events if there is no
spare VDEV available. Added zpool_vdev_remove_wanted() in libzfs
and vdev_remove_wanted() in vdev.c to remove the VDEV through ZED
on removal event. This means that if you are running zed and
remove a disk, it will be properly marked as REMOVED.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#13797
The current value causes significant artificial slowdown during mass
parallel file removal, which can be observed both on FreeBSD and Linux
when running real workloads.
Sample results from Linux doing make -j 96 clean after an allyesconfig
modules build:
before: 4.14s user 6.79s system 48% cpu 22.631 total
after: 4.17s user 6.44s system 153% cpu 6.927 total
FreeBSD results in the ticket.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#13932Closes#13938
Coverity caught unsafe use of `strcpy()` in `ztest_dmu_objset_own()`,
`nfs_init_tmpfile()` and `dump_snapshot()`. It also caught an unsafe use
of `strlcat()` in `nfs_init_tmpfile()`.
Inspired by this, I did an audit of every single usage of `strcpy()` and
`strcat()` in the code. If I could not prove that the usage was safe, I
changed the code to use either `strlcpy()` or `strlcat()`, depending on
which function was originally used. In some cases, `snprintf()` was used
to replace multiple uses of `strcat` because it was cleaner.
Whenever I changed a function, I preferred to use `sizeof(dst)` when the
compiler is able to provide the string size via that. When it could not
because the string was passed by a caller, I checked the entire call
tree of the function to find out how big the buffer was and hard coded
it. Hardcoding is less than ideal, but it is safe unless someone shrinks
the buffer sizes being passed.
Additionally, Coverity reported three more string related issues:
* It caught a case where we do an overlapping memory copy in a call to
`snprintf()`. We fix that via `kmem_strdup()` and `kmem_strfree()`.
* It caught `sizeof (buf)` being used instead of `buflen` in
`zdb_nicenum()`'s call to `zfs_nicenum()`, which is passed to
`snprintf()`. We change that to pass `buflen`.
* It caught a theoretical unterminated string passed to `strcmp()`.
This one is likely a false positive, but we have the information
needed to do this more safely, so we change this to silence the false
positive not just in coverity, but potentially other static analysis
tools too. We switch to `strncmp()`.
* There was a false positive in tests/zfs-tests/cmd/dir_rd_update.c. We
suppress it by switching to `snprintf()` since other static analysis
tools might complain about it too. Interestingly, there is a possible
real bug there too, since it assumes that the passed directory path
ends with '/'. We add a '/' to fix that potential bug.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13913
Coverity complains about a possible NULL pointer dereference. This is
impossible, but it suspects it because we do a NULL check against
`spa->spa_root_vdev`. This NULL check was never necessary and makes the
code harder to understand, so we drop it.
In particular, we dereference `spa->spa_root_vdev` when `new_state !=
POOL_STATE_UNINITIALIZED && !hardforce`. The first is only true when
spa_reset is called, which only occurs under fault injection. The
second is true unless `zpool export -F $POOLNAME` is used. Therefore,
we effectively *always* dereference the pointer. In the cases where we
do not, there is no reason to think it is unsafe. Therefore this change
is safe to make.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13905
In #13871, zfs_vdev_aggregation_limit_non_rotating and
zfs_vdev_aggregation_limit being signed was pointed out as a possible
reason not to eliminate an unnecessary MAX(unsigned, 0) since the
unsigned value was assigned from them.
There is no reason for these module parameters to be signed and upon
inspection, it was found that there are a number of other module
parameters that are signed, but should not be, so we make them unsigned.
Making them unsigned made it clear that some other variables in the code
should also be unsigned, so we also make those unsigned. This prevents
users from setting negative values that could potentially cause bad
behaviors. It also makes the code slightly easier to understand.
Mostly module parameters that deal with timeouts, limits, bitshifts and
percentages are made unsigned by this. Any that are boolean are left
signed, since whether booleans should be considered signed or unsigned
does not matter.
Making zfs_arc_lotsfree_percent unsigned caused a
`zfs_arc_lotsfree_percent >= 0` check to become redundant, so it was
removed. Removing the check was also necessary to prevent a compiler
error from -Werror=type-limits.
Several end of line comments had to be moved to their own lines because
replacing int with uint_t caused us to exceed the 80 character limit
enforced by cstyle.pl.
The following were kept signed because they are passed to
taskq_create(), which expects signed values and modifying the
OpenSolaris/Illumos DDI is out of scope of this patch:
* metaslab_load_pct
* zfs_sync_taskq_batch_pct
* zfs_zil_clean_taskq_nthr_pct
* zfs_zil_clean_taskq_minalloc
* zfs_zil_clean_taskq_maxalloc
* zfs_arc_prune_task_threads
Also, negative values in those parameters was found to be harmless.
The following were left signed because either negative values make
sense, or more analysis was needed to determine whether negative values
should be disallowed:
* zfs_metaslab_switch_threshold
* zfs_pd_bytes_max
* zfs_livelist_min_percent_shared
zfs_multihost_history was made static to be consistent with other
parameters.
A number of module parameters were marked as signed, but in reality
referenced unsigned variables. upgrade_errlog_limit is one of the
numerous examples. In the case of zfs_vdev_async_read_max_active, it was
already uint32_t, but zdb had an extern int declaration for it.
Interestingly, the documentation in zfs.4 was right for
upgrade_errlog_limit despite the module parameter being wrongly marked,
while the documentation for zfs_vdev_async_read_max_active (and friends)
was wrong. It was also wrong for zstd_abort_size, which was unsigned,
but was documented as signed.
Also, the documentation in zfs.4 incorrectly described the following
parameters as ulong when they were int:
* zfs_arc_meta_adjust_restarts
* zfs_override_estimate_recordsize
They are now uint_t as of this patch and thus the man page has been
updated to describe them as uint.
dbuf_state_index was left alone since it does nothing and perhaps should
be removed in another patch.
If any module parameters were missed, they were not found by `grep -r
'ZFS_MODULE_PARAM' | grep ', INT'`. I did find a few that grep missed,
but only because they were in files that had hits.
This patch intentionally did not attempt to address whether some of
these module parameters should be elevated to 64-bit parameters, because
the length of a long on 32-bit is 32-bit.
Lastly, it was pointed out during review that uint_t is a better match
for these variables than uint32_t because FreeBSD kernel parameter
definitions are designed for uint_t, whose bit width can change in
future memory models. As a result, we change the existing parameters
that are uint32_t to use uint_t.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Neal Gompa <ngompa@datto.com>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13875
Coverity found a bug in `zfs_secpolicy_create_clone()` where it is
possible for us to pass an unterminated string when `zfs_get_parent()`
returns an error. Upon inspection, it is clear that using `strlcpy()`
would have avoided this issue.
Looking at the codebase, there are a number of other uses of `strncpy()`
that are unsafe and even when it is used safely, switching to
`strlcpy()` would make the code more readable. Therefore, we switch all
instances where we use `strncpy()` to use `strlcpy()`.
Unfortunately, we do not portably have access to `strlcpy()` in
tests/zfs-tests/cmd/zfs_diff-socket.c because it does not link to
libspl. Modifying the appropriate Makefile.am to try to link to it
resulted in an error from the naming choice used in the file. Trying to
disable the check on the file did not work on FreeBSD because Clang
ignores `#undef` when a definition is provided by `-Dstrncpy(...)=...`.
We workaround that by explictly including the C file from libspl into
the test. This makes things build correctly everywhere.
We add a deprecation warning to `config/Rules.am` and suppress it on the
remaining `strncpy()` usage. `strlcpy()` is not portably avaliable in
tests/zfs-tests/cmd/zfs_diff-socket.c, so we use `snprintf()` there as a
substitute.
This patch does not tackle the related problem of `strcpy()`, which is
even less safe. Thankfully, a quick inspection found that it is used far
more correctly than strncpy() was used. A quick inspection did not find
any problems with `strcpy()` usage outside of zhack, but it should be
said that I only checked around 90% of them.
Lastly, some of the fields in kstat_t varied in size by 1 depending on
whether they were in userspace or in the kernel. The origin of this
discrepancy appears to be 04a479f706 where
it was made for no apparent reason. It conflicts with the comment on
KSTAT_STRLEN, so we shrink the kernel field sizes to match the userspace
field sizes.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13876
When receiving full/newfs on existing dataset, then it should be done
with "-F" flag. Its enforced for initial receive in checks done in
zfs_receive_one function of libzfs. Similarly, on resuming full/newfs
recv on existing dataset, it should be done with "-F" flag.
When dataset doesn't exist, then full/new recv is done on newly created
dataset and it's marked INCONSISTENT. But when receiving on existing
dataset, recv is first done on %recv and its marked INCONSISTENT.
Existing dataset is not marked INCONSISTENT. Resume of full/newfs
receive with dataset not INCONSISTENT indicates that its resuming newfs
on existing dataset. So, enforce "-F" flag in this case.
Also return an error from dmu_recv_resume_begin_check() in zfs kernel,
when its resuming full/newfs recv without force.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Chunwei Chen <david.chen@nutanix.com>
Signed-off-by: Jitendra Patidar <jitendra.patidar@nutanix.com>
Closes#13856Closes#13857
Recently, I have been making a push to fix things that coverity found.
However, I was curious what Clang's static analyzer reported, so I ran
it and found things that coverity had missed.
* contrib/pam_zfs_key/pam_zfs_key.c: If prop_mountpoint is passed more
than once, we leak memory.
* module/zfs/zcp_get.c: We leak memory on temporary properties in
userspace.
* tests/zfs-tests/cmd/draid.c: On error from vdev_draid_rand(), we leak
memory if best_map had been allocated by a prior iteration.
* tests/zfs-tests/cmd/mkfile.c: Memory used by the loop is not freed
before program termination.
Arguably, these are all minor issues, but if we ignore them, then they
could obscure serious bugs, so we fix them.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13955
Coverity found a number of places where we either do MAX(unsigned, 0) or
do assertions that a unsigned variable is >= 0. These do nothing, so
let us drop them all.
It also found a spot where we do `if (unsigned >= 0 && ...)`. Let us
also drop the unsigned >= 0 check.
Reviewed-by: Neal Gompa <ngompa@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13871
Coverity complained about unchecked return values and unused values that
turned out to be unused return values.
Different approaches were used to handle the different cases of
unchecked return values:
* cmd/zdb/zdb.c: VERIFY0 was used in one place since the existing code
had no error handling. An error message was printed in another to
match the rest of the code.
* cmd/zed/agents/zfs_retire.c: We dismiss the return value with `(void)`
because the value is expected to be potentially unset.
* cmd/zpool_influxdb/zpool_influxdb.c: We dismiss the return value with
`(void)` because the values are expected to be potentially unset.
* cmd/ztest.c: VERIFY0 was used since we want failures if something goes
wrong in ztest.
* module/zfs/dsl_dir.c: We dismiss the return value with `(void)`
because there is no guarantee that the zap entry will always be there.
For example, old pools imported readonly would not have it and we do
not want to fail here because of that.
* module/zfs/zfs_fm.c: `fnvlist_add_*()` was used since the
allocations sleep and thus can never fail.
* module/zfs/zvol.c: We dismiss the return value with `(void)` because
we do not need it. This matches what is already done in the analogous
`zfs_replay_write2()`.
* tests/zfs-tests/cmd/draid.c: We suppress one return value with
`(void)` since the code handles errors already. The other return value
is handled by switching to `fnvlist_lookup_uint8_array()`.
* tests/zfs-tests/cmd/file/file_fadvise.c: We add error handling.
* tests/zfs-tests/cmd/mmap_sync.c: We add error handling for munmap, but
ignore failures on remove() with (void) since it is expected to be
able to fail.
* tests/zfs-tests/cmd/mmapwrite.c: We add error handling.
As for unused return values, they were all in places where there was
error handling, so logic was added to handle the return values.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13920
Incorrectly sizing the array of hash locks used to protect the
dbuf hash table can lead to contention and reduce performance.
We could unconditionally allocate a larger array for the locks
but it's wasteful, particularly for a low-memory system.
Instead, dynamically allocate the array of locks and scale
it based on total system memory.
Additionally, add a new `dbuf_mutex_cache_shift` module option
which can be used to override the hash lock array size. This is
disabled by default (dbuf_mutex_hash_shift=0) and can only be
set at module load time. The minimum target array size is set
to 8192, this matches the current constant value.
Note that the count of the dbuf hash table and count of the
mutex array were added to the /proc/spl/kstat/zfs/dbufstats
kstat.
Finally, this change removes the _KERNEL conditional checks.
These were not required since for the user space build there
is no difference between the kmem and vmem interfaces.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13928
This reverts commit 34dbc618f5. While this
change resolved the lock contention observed for certain workloads, it
inadventantly reduced the maximum hash inserts/removes per second. This
appears to be due to the slightly higher acquisition cost of a rwlock vs
a mutex.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Coverity complains about this. It is not a bug as long as we never shift
by more than 31, but it is not terrible to change the constants from 1
to 1ULL as clean up.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13914
For encrypted raw receive, objset creation is delayed until a call to
dmu_recv_stream(). ZFS_PROP_SHARESMB property requires objset to be
populated when calling zpl_earlier_version(). To correctly handle the
ZFS_PROP_SHARESMB property for encrypted raw receive, this change
delays setting the property.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#13878
Coverity complained about the format specifiers not matching variables.
In one case, the variable is a constant, so we fix it. In another, we
were missing an argument (about which coverity also complained).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13888
Apply similar options to BLAKE3 as it is done for zfs_fletcher_4_impl.
The zfs module parameter on Linux changes from icp_blake3_impl to
zfs_blake3_impl.
You can check and set it on Linux via sysfs like this:
```
[bash]# cat /sys/module/zfs/parameters/zfs_blake3_impl
cycle [fastest] generic sse2 sse41 avx2
[bash]# echo sse2 > /sys/module/zfs/parameters/zfs_blake3_impl
[bash]# cat /sys/module/zfs/parameters/zfs_blake3_impl
cycle fastest generic [sse2] sse41 avx2
```
The modprobe module parameters may also be used now:
```
[bash]# modprobe zfs zfs_blake3_impl=sse41
[bash]# cat /sys/module/zfs/parameters/zfs_blake3_impl
cycle fastest generic sse2 [sse41] avx2
```
On FreeBSD the BLAKE3 implementation can be set via sysctl like this:
```
[bsd]# sysctl vfs.zfs.blake3_impl
vfs.zfs.blake3_impl: cycle [fastest] generic sse2 sse41 avx2
[bsd]# sysctl vfs.zfs.blake3_impl=sse2
vfs.zfs.blake3_impl: cycle [fastest] generic sse2 sse41 avx2 \
-> cycle fastest generic [sse2] sse41 avx2
```
This commit changes also some Blake3 internals like these:
- blake3_impl_ops_t was renamed to blake3_ops_t
- all functions are named blake3_impl_NAME() now
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Co-authored-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Tino Reichardt <milky-zfs@mcmilk.de>
Closes#13725
- Some optimizations for bqueue enqueue/dequeue.
- Added a fix to prevent deadlock when both bqueue_enqueue_impl()
and bqueue_dequeue() waits for signal to be triggered.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#13855
Replace ZFS_ENTER and ZFS_VERIFY_ZP, which have hidden returns, with
functions that return error code. The reason we want to do this is
because hidden returns are not obvious and had caused some missing fail
path unwinding.
This patch changes the common, linux, and freebsd parts. Also fixes
fail path unwinding in zfs_fsync, zpl_fsync, zpl_xattr_{list,get,set}, and
zfs_lookup().
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Chunwei Chen <david.chen@nutanix.com>
Closes#13831
I see a few issues in the issue tracker that might be aided by being
able to turn this on. We have no module parameter for it, so I would
like to add one.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13874
We pass sizeof (struct redact_record *) rather than sizeof (struct
redact_record). Passing the pointer size is wrong.
Coverity caught this in two places.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13885
Coverity pointed out that if we somehow receive SPA_FEATURE_NONE, we
will use a negative number as an array index. A defensive assertion
seems appropriate.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Neal Gompa <ngompa@datto.com>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13872
Coverity complains about a "use-after-free" bug in
`dbuf_prefetch_indirect_done()` because we use a pointer value after
freeing its buffer. The pointer is used for refcounting in ARC (as the
reference holder). There is a theoretical situation where the pointer
would be reused in a way that causes the refcounting to collide, so we
change the order in which we call arc_buf_destroy() and
dbuf_prefetch_fini() to match the rest of the function. This prevents
the theoretical situation from being a possibility.
Also, we have a few return statements with a value, despite this being a
void function. We clean those up while we are making changes here.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Neal Gompa <ngompa@datto.com>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13869
We inherited membar_consumer() and membar_producer() from OpenSolaris,
but we had replaced membar_consumer() with Linux's smp_rmb() in
zfs_ioctl.c. The FreeBSD SPL consequently implemented a shim for the
Linux-only smp_rmb().
We reinstate membar_consumer() in platform independent code and fix the
FreeBSD SPL to implement membar_consumer() in a way analogous to Linux.
Reviewed-by: Konstantin Belousov <kib@FreeBSD.org>
Reviewed-by: Mateusz Guzik <mjguzik@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Neal Gompa <ngompa@datto.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13843
Unused code detected by coverity.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Neal Gompa <ngompa@datto.com>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13868
Coverity reported this as an out-of-bounds read.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Neal Gompa <ngompa@datto.com>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13865
Coverty static analysis found these.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Neal Gompa <ngompa@datto.com>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#10989Closes#13861
In our codebase, `cond_resched() and `schedule()` are Linux kernel
functions that have replaced the OpenSolaris `kpreempt()` functions in
the codebase to such an extent that `kpreempt()` in zfs_context.h was
broken. Nobody noticed because we did not actually use it. The header
had defined `kpreempt()` as `yield()`, which works on OpenSolaris and
Illumos where `sched_yield()` is a wrapper for `yield()`, but that does
not work on any other platform.
The FreeBSD platform specific code implemented shims for these, but the
shim for `schedule()` forced us to wait, which is different than merely
rescheduling to another thread as the original Linux code does, while
the shim for `cond_resched()` had the same definition as its kernel
kpreempt() shim.
After studying this, I have concluded that we should reintroduce the
kpreempt() function in platform independent code with the following
definitions:
- In the Linux kernel:
kpreempt(unused) -> cond_resched()
- In the FreeBSD kernel:
kpreempt(unused) -> kern_yield(PRI_USER)
- In userspace:
kpreempt(unused) -> sched_yield()
In userspace, nothing changes from this cleanup. In the kernels, the
function `fm_fini()` will now call `kern_yield(PRI_USER)` on FreeBSD and
`cond_resched()` on Linux. This is instead of `pause("schedule", 1)` on
FreeBSD and `schedule()` on Linux. This makes our behavior consistent
across platforms.
Note that Linux's SPL continues to use `cond_resched()` and
`schedule()`. However, those functions have been removed from both the
FreeBSD code and userspace code.
This should have the benefit of making it slightly easier to port the
code to new platforms by making how things should be mapped less
confusing.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Neal Gompa <ngompa@datto.com>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13845
When iterating through children physical ashifts for vdev, prefer
ones above the maximum logical ashift, that we can actually use,
but within the administrator defined maximum.
When selecting top-level vdev ashift, do not set it to the defined
maximum in case physical ashift is even higher, but just ignore one.
Using the maximum does not prevent misaligned writes, but reduces
space efficiency. Since ZFS tries to write data sequentially and
aggregates the writes, in many cases large misanigned writes may be
not as bad as the space penalty otherwise.
Allow internal physical ashifts for vdevs higher than SHIFT_MAX.
May be one day allocator or aggregation could benefit from that.
Reduce zfs_vdev_max_auto_ashift default from 16 (64KB) to 14 (16KB),
so that ZFS may still use bigger ashifts up to SHIFT_MAX (64KB),
but only if it really has to or explicitly told to, but not as an
"optimization".
There are some read-intensive NVMe SSDs that report Preferred Write
Alignment of 64KB, and attempt to build RAIDZ2 of those leads to a
space inefficiency that can't be justified. Instead these changes
make ZFS fall back to logical ashift of 12 (4KB) by default and
only warn user that it may be suboptimal for performance.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#13798
This commit adds DD_FIELD string used in extensified dsl_dir zap object
for snapshots_changed property.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Umer Saleem <usaleem@ixsystems.com>
Closes#13819
Only the single snapshot rename is provided.
The recursive or more complex rename can be scripted.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Andriy Gapon <avg@FreeBSD.org>
Closes#13802
It makes sense to free memory in smaller chunks when approaching
arc_c_min to let other kernel subsystems to free more, since after
that point we can't free anything. This also matches behavior on
Linux, where to shrinker reported only the size above arc_c_min.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#13794
This reverts commit 80a650b7bb. This change
inadvertently introduced a regression in ztest where one of the new ASSERTs
is triggered in dsl_scan_visitbp().
Reviewed-by: George Amanakis <gamanakis@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #12275Closes#13799
Currently, snapshots_changed property is stored in dd_props_zapobj, due
to which the property is assumed to be local. This causes a difference
in behavior with respect to other readonly properties.
This commit stores the snapshots_changed property in dd_object. Source
is not set to local in this case, which makes it consistent with other
readonly properties.
This commit also updates the date string format to include seconds.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Umer Saleem <usaleem@ixsystems.com>
Closes#13785
When scrubbing an encrypted filesystem with unloaded key still report an
error in zpool status.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alek Pinchuk <apinchuk@axcient.com>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#13675Closes#13717
There are a couple changes included here. The first is to introduce
a cap on the size the ZED will grow the zevent list to. One million
entries is more than enough for most use cases, and if you are
overflowing that value, the problem needs to be addressed another
way. The value is also tunable, for those who want the limit to be
higher or lower.
The other change is to add a kernel module parameter that allows
snapshot creation/deletion to be exempted from the history logging;
for most workloads, having these things logged is valuable, but for
some workloads it produces large quantities of log spam and isn't
especially helpful.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Issue #13374Closes#13753
Thanks to George Wilson for clarifying this on Slack.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Wilson <gwilson@delphix.com>
Signed-off-by: Christian Schwarz <christian.schwarz@nutanix.com>
Closes#13698
This is a small cleanup for a trivial problem which happened to
be noticed while another issue was being investigated.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#13730
Make dd_snap_cmtime property persistent across mount and unmount
operations by storing in ZAP and restore the value from ZAP on hold
into dd_snap_cmtime instead of updating it.
Expose dd_snap_cmtime as 'snapshots_changed' property that provides a
mechanism to quickly determine whether snapshot list for dataset has
changed without having to mount a dataset or iterate the snapshot list.
It specifies the time at which a snapshot for a dataset was last
created or deleted. This allows us to be more efficient how often we
query snapshots.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Umer Saleem <usaleem@ixsystems.com>
Closes#13635
The checksum benchmarking on module load may take a really long time
on embedded systems with a slow cpu. Avoid all benchmarks >= 1MiB on
systems, where EdonR is slower then 300 MiB/s.
This limit is currently hardcoded via the define LIMIT_PERF_MBS.
This is the new benchmark output of a slow Intel Atom:
```
implementation 1k 4k 16k 64k 256k 1m 4m 16m
edonr-generic 209 257 268 259 262 0 0 0
skein-generic 129 150 151 150 150 0 0 0
sha256-generic 50 55 56 56 56 0 0 0
sha512-generic 76 86 88 89 88 0 0 0
blake3-generic 63 62 62 62 61 0 0 0
blake3-sse2 114 292 301 307 309 0 0 0
```
Reviewed-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tino Reichardt <milky-zfs@mcmilk.de>
Closes#13695
This type of recv is used to heal corrupted data when a replica
of the data already exists (in the form of a send file for example).
With the provided send stream, corrective receive will read from
disk blocks described by the WRITE records. When any of the reads
come back with ECKSUM we use the data from the corresponding WRITE
record to rewrite the corrupted block.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Paul Zuchowski <pzuchowski@datto.com>
Signed-off-by: Alek Pinchuk <apinchuk@axcient.com>
Closes#9372
- When iterating snapshots with name only, e.g., "-o name -s name",
libzfs uses simple snapshot iterator and results are displayed
in alphabetic order. This PR adds support for faster version of
createtxg sort by avoiding nvlist parsing for properties. Flags
"-o name -s createtxg" will enable createtxg sort while using
simple snapshot iterator.
- Added support to read createtxg property directly from zfs handle
for filesystem, volume and snapshot types instead of parsing nvlist.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#13577
ZIL kstats are reported in an inclusive way, i.e., same counters are
shared to capture all the activities happening in zil. Added support
to report zil stats for every datset individually by combining them
with already exposed dataset kstats.
Wmsum uses per cpu counters and provide less overhead as compared
to atomic operations. Updated zil kstats to replace wmsum counters
to avoid atomic operations.
Reviewed-by: Christian Schwarz <christian.schwarz@nutanix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#13636
It may happen that scan bookmark points to a block that was turned
into a part of a big hole. In such case dsl_scan_visitbp() may skip
it and dsl_scan_check_resume() will not be called for it. As result
new scan suspend won't be possible until the end of the object, that
may take hours if the object is a multi-terabyte ZVOL on a slow HDD
pool, stretching TXG to all that time, creating all sorts of problems.
This patch changes the resume condition to any greater or equal block,
so even if we miss the bookmarked block, the next one we find will
delete the bookmark, allowing new suspend.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#13643
Allocation via kmem_cache_alloc() is limited to less then 4m for
some architectures.
This commit limits the benchmarks with the linear abd cache to 1m
on all architectures and adds 4m + 16m benchmarks via non-linear
abd_alloc().
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Co-authored-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Tino Reichardt <milky-zfs@mcmilk.de>
Closes#13669Closes#13670
Fixes a small kernel memory leak which would occur if a pool failed
to import because the `DMU_POOL_VDEV_ZAP_MAP` key can't be read from
a presumably damaged MOS config. In the case of a missing key there
was no leak.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Finix1979 <yancw@info2soft.com>
Closes#13629
Before this change for every valid parity column raidz_parity_verify()
allocated new buffer and copied there existing data, then recalculated
the parity and compared the result with the copy. This patch removes
the memory copy, simply swapping original buffer pointers with newly
allocated empty ones for parity recalculation and comparison. Original
buffers with potentially incorrect parity data are then just freed,
while new recalculated ones are used for repair.
On a pool of 12 4-wide raidz vdevs, storing 1.5TB of 16MB blocks, this
change reduces memory traffic during scrub by 17% and total unhalted
CPU time by 25%.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#13613
Issuing several scrub reads for a block we may use the parent ZIO
buffer for one of child ZIOs. If that read complete successfully,
then we won't need to copy the data explicitly. If block has only
one copy (typical for root vdev, which is also a mirror inside),
then we never need to copy -- succeed or fail as-is. Previous
code also copied data from buffer of every successfully completed
child ZIO, but that just does not make any sense.
On healthy N-wide mirror this saves all N+1 (or even more in case
of ditto blocks) memory copies for each scrubbed block, allowing
CPU to focus mostly on check-summing. For other vdev types it
should save one memory copy per block copy at root vdev.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#13606
If a dnode has a spill pointer, and we use DN_SLOTS_TO_BONUSLEN() then
we will possibly include the spill pointer in the len calculation and it
will be byteswapped. Then dnode_byteswap() will carry on and swap the
spill pointer again. Fix this by using DN_MAX_BONUS_LEN() instead.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#13002Closes#13015
Block statistics calculation during scrub I/O issue in case of sorted
scrub accounted ditto blocks several times. Embedded blocks on other
side were not accounted at all. This change moves the accounting from
issue to scan stage, that fixes both problems and also allows to avoid
pool-wide locking and the lock contention it created.
Since this statistics is quite specific and is not even exposed now
anywhere, disable its calculation by default to not waste CPU time.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#13579
Move the use of the db pointer after it is freed. It's only used as
a tag so a dereference would never occur, but there's no reason we
can't invert the order to resolve the warning.
module/zfs/dbuf.c: In function 'dbuf_destroy':
module/zfs/dbuf.c:2953:17: error:
pointer 'db' may be used after 'free' [-Werror=use-after-free]
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13528Closes#13575
Move the use of the private pointer after it is freed. It's only
used as a tag so a dereference would never occur, but there's no
harm in inverting the order to resolve the warning.
module/zfs/dbuf.c: In function 'dbuf_issue_final_prefetch_done':
module/zfs/dbuf.c:3204:17: error:
pointer 'private' may be used after 'free' [-Werror=use-after-free]
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13528Closes#13575
The memcpy(), memmove(), and memset() functions have been annotated
to perform bounds checking when using FORTIFY_SOURCE. A warning is
now generted when writing beyond the end of the specified field.
Alternately, the new struct_group() macro could be used to create
an anonymous union member for use by memcpy(). However, since this
is the only place the macro would be helpful it's preferable to
restructure the code slights to avoid the need for additional
compatibility code when the macro does not exist.
https://lore.kernel.org/lkml/20211118183807.1283332-1-keescook@chromium.org/T/
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13528Closes#13575
Restructure the code in zfs_log_xvattr() to use a lr_attr_end
structure when accessing lr_attr_t elements located after the
variable sized array. This makes the code more understandable
and resolves the accessing beyond the end of the field warnings.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13528Closes#13575
The current codebase does not support raw sending buffers with block
size > 128kB when large_blocks is not active. This can happen in the
codepath dsl_dataset_sync()->dmu_objset_sync()->zio_nowait() which
calls back dmu_objset_write_done()->dsl_dataset_block_born(). If
dsl_dataset_sync() completes its run before dsl_dataset_block_born() is
called, we will end up not activating some of the necessary flags, while
having blocks based on those flags written in the filesystem. A
subsequent send will then panic.
Fix this by directly deciding in dmu_objset_sync() whether these flags
need to be activated later by dsl_dataset_sync(). Instead of panicking
due to a NULL pointer dereference in dmu_dump_write() in case of a send,
print out an error message. Also during scrub verify there are no
contradicting filesystem flags.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#12275Closes#12438
Change math to make it like the ARC, using multiplications instead.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#13591
- Introduce first element offset within a leaf. It allows to reduce
by ~50% average memmove() size when adding/removing elements. If the
added/removed element is in the first half of the leaf, we may shift
elements before it and adjust the bth_first instead of moving more
elements after it.
- Use memcpy() instead of memmove() when we know there is no overlap.
- Switch from uint64_t to uint32_t. It does not limit anything,
but 32-bit arches should appreciate it greatly in hot paths.
- Store leaf capacity in struct btree to avoid 64-bit divisions.
- Adjust zfs_btree_insert_into_leaf() to always result in balanced
leaves after splitting, no matter where the new element was inserted.
Not that we care about it much, but it should also allow B-trees with
as little as two elements per leaf instead of 4 previously.
When scrubbing pool of 12 SSDs, storing 1.5TB of 4KB zvol blocks this
reduces amount of time spent in memmove() inside the scan thread from
13.7% to 5.7% and total scrub time by ~15 seconds out of 9 minutes.
It should also reduce spacemaps load time, but I haven't measured it.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#13582
- Reduce size and comparison complexity of q_exts_by_size B-tree.
Previous code used two 64-bit divisions and many other operations to
compare two B-tree elements. It created enormous overhead. This
implementation moves the math to the upper level and stores the score
in the B-tree elements themselves. Since all that we need to store in
that B-tree is the extent score and offset, those can fit into single
8 byte value instead of 24 bytes of q_exts_by_addr element and can be
compared with single operation.
- Better decouple secondary tree logic from main range_tree by moving
rt_btree_ops and related functions into dsl_scan.c as ext_size_ops.
Those functions are very small to worry about the code duplication and
range_tree does not need to know details such as rt_btree_compare.
- Instead of accounting number of pending bytes per pool, that needs
atomic on global variable per block, account the number of non-empty
per-vdev queues, that change much more rarely.
- When extent scan is interrupted by TXG end, continue it in the next
TXG instead of selecting next best extent. It allows to avoid leaving
one truncated (and so likely not the best any more) extent each TXG.
On top of some other optimizations this saves about 1.5 minutes out of
10 to scrub pool of 12 SSDs, storing 1.5TB of 4KB zvol blocks.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tom Caputi <caputit1@tcnj.edu>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#13576
When scrubbing a raidz/draid pool, which contains a replacing or
sparing mirror with multiple online children, only one child will
be read. This is not normally a serious concern because the DTL
records are used to determine where a good copy of the data is.
As long as the data can be read from one child the mirror vdev
will use it to repair gaps in any of its children. Furthermore,
even if the data which was read is corrupt the raidz code will
detect this and issue its own repair I/O to correct the damage
in the mirror vdev.
However, in the scenario where the DTL is wrong due to silent
data corruption (say due to overwriting one child) and the scrub
happens to read from a child with good data, then the other damaged
mirror child will not be detected nor repaired.
While this is possible for both raidz and draid vdevs, it's most
pronounced when using draid. This is because by default the zed
will sequentially rebuild a draid pool to a distributed spare,
and the distributed spare half of the mirror is always preferred
since it delivers better performance. This means the damaged
half of the mirror will go undetected even after scrubbing.
For system administrations this behavior is non-intuitive and in
a worst case scenario could result in the only good copy of the
data being unknowingly detached from the mirror.
This change resolves the issue by reading all replacing/sparing
mirror children when scrubbing. When the BP isn't available for
verification, then compare the data buffers from each child. They
must all be identical, if not there's silent damage and an error
is returned to prompt the top-level vdev to issue a repair I/O to
rewrite the data on all of the mirror children. Since we can't
tell which child was wrong a checksum error is logged against the
replacing or sparing mirror vdev.
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13555
The kmem_alloc(sizeof (*ctx), KM_NOSLEEP) call on FreeBSD can't be
used in this code segment. Work around this by pre-allocating a percpu
context array for later use.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tino Reichardt <milky-zfs@mcmilk.de>
Closes#13568
During sorted scrub multiple threads (one per vdev) are issuing many
ZIOs same time, all using the same scn->scn_zio_root ZIO as parent.
It causes huge lock contention on the single global lock on that ZIO.
Improve it by introducing per-queue null ZIOs, children to that one,
and using them instead as proxy.
For 12 SSD pool storing 1.5TB of 4KB blocks on 80-core system this
dramatically reduces lock contention and reduces scrub time from 21
minutes down to 12.5, while actual read stages (not scan) are about
3x faster, reaching 100K blocks per second per vdev.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#13553
Since we use two B-trees q_exts_by_size and q_exts_by_addr, we should
count 2x sizeof (range_seg_gap_t) per node. And since average B-tree
memory efficiency is about 75%, we should increase it to 3x.
Previous code under-counted up to 30% of the memory usage.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#13537
This commit adds BLAKE3 checksums to OpenZFS, it has similar
performance to Edon-R, but without the caveats around the latter.
Homepage of BLAKE3: https://github.com/BLAKE3-team/BLAKE3
Wikipedia: https://en.wikipedia.org/wiki/BLAKE_(hash_function)#BLAKE3
Short description of Wikipedia:
BLAKE3 is a cryptographic hash function based on Bao and BLAKE2,
created by Jack O'Connor, Jean-Philippe Aumasson, Samuel Neves, and
Zooko Wilcox-O'Hearn. It was announced on January 9, 2020, at Real
World Crypto. BLAKE3 is a single algorithm with many desirable
features (parallelism, XOF, KDF, PRF and MAC), in contrast to BLAKE
and BLAKE2, which are algorithm families with multiple variants.
BLAKE3 has a binary tree structure, so it supports a practically
unlimited degree of parallelism (both SIMD and multithreading) given
enough input. The official Rust and C implementations are
dual-licensed as public domain (CC0) and the Apache License.
Along with adding the BLAKE3 hash into the OpenZFS infrastructure a
new benchmarking file called chksum_bench was introduced. When read
it reports the speed of the available checksum functions.
On Linux: cat /proc/spl/kstat/zfs/chksum_bench
On FreeBSD: sysctl kstat.zfs.misc.chksum_bench
This is an example output of an i3-1005G1 test system with Debian 11:
implementation 1k 4k 16k 64k 256k 1m 4m
edonr-generic 1196 1602 1761 1749 1762 1759 1751
skein-generic 546 591 608 615 619 612 616
sha256-generic 240 300 316 314 304 285 276
sha512-generic 353 441 467 476 472 467 426
blake3-generic 308 313 313 313 312 313 312
blake3-sse2 402 1289 1423 1446 1432 1458 1413
blake3-sse41 427 1470 1625 1704 1679 1607 1629
blake3-avx2 428 1920 3095 3343 3356 3318 3204
blake3-avx512 473 2687 4905 5836 5844 5643 5374
Output on Debian 5.10.0-10-amd64 system: (Ryzen 7 5800X)
implementation 1k 4k 16k 64k 256k 1m 4m
edonr-generic 1840 2458 2665 2719 2711 2723 2693
skein-generic 870 966 996 992 1003 1005 1009
sha256-generic 415 442 453 455 457 457 457
sha512-generic 608 690 711 718 719 720 721
blake3-generic 301 313 311 309 309 310 310
blake3-sse2 343 1865 2124 2188 2180 2181 2186
blake3-sse41 364 2091 2396 2509 2463 2482 2488
blake3-avx2 365 2590 4399 4971 4915 4802 4764
Output on Debian 5.10.0-9-powerpc64le system: (POWER 9)
implementation 1k 4k 16k 64k 256k 1m 4m
edonr-generic 1213 1703 1889 1918 1957 1902 1907
skein-generic 434 492 520 522 511 525 525
sha256-generic 167 183 187 188 188 187 188
sha512-generic 186 216 222 221 225 224 224
blake3-generic 153 152 154 153 151 153 153
blake3-sse2 391 1170 1366 1406 1428 1426 1414
blake3-sse41 352 1049 1212 1174 1262 1258 1259
Output on Debian 5.10.0-11-arm64 system: (Pi400)
implementation 1k 4k 16k 64k 256k 1m 4m
edonr-generic 487 603 629 639 643 641 641
skein-generic 271 299 303 308 309 309 307
sha256-generic 117 127 128 130 130 129 130
sha512-generic 145 165 170 172 173 174 175
blake3-generic 81 29 71 89 89 89 89
blake3-sse2 112 323 368 379 380 371 374
blake3-sse41 101 315 357 368 369 364 360
Structurally, the new code is mainly split into these parts:
- 1x cross platform generic c variant: blake3_generic.c
- 4x assembly for X86-64 (SSE2, SSE4.1, AVX2, AVX512)
- 2x assembly for ARMv8 (NEON converted from SSE2)
- 2x assembly for PPC64-LE (POWER8 converted from SSE2)
- one file for switching between the implementations
Note the PPC64 assembly requires the VSX instruction set and the
kfpu_begin() / kfpu_end() calls on PowerPC were updated accordingly.
Reviewed-by: Felix Dörre <felix@dogcraft.de>
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tino Reichardt <milky-zfs@mcmilk.de>
Co-authored-by: Rich Ercolani <rincebrain@gmail.com>
Closes#10058Closes#12918
It is typical, but not generally true that if log summary has more
blocks it must also have unflushed metaslabs. Normally with metaslabs
flushed in order it works, but there are known exceptions, such as
device removal or metaslab being loaded during its flush attempt.
Before 600a02b884 if spa_flush_metaslabs() hit loading metaslab it
usually stopped (unless memlimit is also exceeded), but now it may
flush more metaslabs, just skipping that particular one. This
increased chances of assertion to fire when the skipped metaslab is
flushed on next iteration if all other metaslabs in that summary
entry are already flushed out of order.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#13486Closes#13513
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Closes#13518
In current zil_commit() process, transaction lwb_tx is assigned in
zil_lwb_write_issue(), and is committed in zil_lwb_flush_vdevs_done().
Thus, during lwb write out process, the txg is held in open or quiesing
state, until zil_lwb_flush_vdevs_done() is called. If the zil's zio
latency is high, it will cause txg_sync_thread() to starve.
The goal here is to defer waiting for zil_lwb_flush_vdevs_done to the
'syncing' txg state. That is, in zil_sync().
In this patch, it achieves the goal without holding transaction.
A new function zil_lwb_flush_wait_all() is introduced. It waits for
the completion of all the zil_lwb_flush_vdevs_done() by given txg.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Prakash Surya <prakash.surya@delphix.com>
Signed-off-by: jxdking <lostking2008@hotmail.com>
Closes#12321
- Make prefetch distance adaptive: up to 4MB prefetch doubles for
every, hit same as before, but after that it grows by 1/8 every time
the prefetch read does not complete in time to satisfy the demand.
My tests show that 4MB is sufficient for wide NVMe pool to saturate
single reader thread at 2.5GB/s, while new 64MB maximum allows the
same thread to reach 1.5GB/s on wide HDD pool. Further distance
increase may increase speed even more, but less dramatic and with
higher latency.
- Allow early reuse of inactive prefetch streams: streams that never
saw hits can be reused immediately if there is a demand, while others
can be reused after 1s of inactivity, starting with the oldest. After
2s of inactivity streams are deleted to free resources same as before.
This allows by several times increase strided read performance on HDD
pool in presence of simultaneous random reads, previously filling the
zfetch_max_streams limit for seconds and so blocking most of prefetch.
- Always issue intermediate indirect block reads with SYNC priority.
Each of those reads if delayed for longer may delay up to 1024 other
block prefetches, that may be not good for wide pools.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#13452
This issue was discovered by zloop runs. When a mirror or other
redundant top-level vdev has a disk failure, and the disk is replaced,
the rebuild process occurs. A removal can happen while this is in
progress. If the removal completes before the rebuild does, the
removal process will try to free the vdev that is still in use.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#13498
Original Log Size Limit implementation blocked all writes in case of
limit reached until the TXG is committed and the log is freed. It
caused huge delays and following speed spikes in application writes.
This implementation instead smoothly throttles writes, using exactly
the same mechanism as used for dirty data.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: jxdking <lostking2008@hotmail.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Issue #12284Closes#13476
It turns out that "do LZ4 and zstd-1 both fail" is a great heuristic
for "don't even bother trying higher zstd tiers".
By way of illustration:
$ cat /incompress | mbuffer | zfs recv -o compression=zstd-12 evenfaster/lowcomp_1M_zstd12_normal
summary: 39.8 GiByte in 3min 40.2sec - average of 185 MiB/s
$ echo 3 | sudo tee /sys/module/zzstd/parameters/zstd_lz4_pass
3
$ cat /incompress | mbuffer -m 4G | zfs recv -o compression=zstd-12 evenfaster/lowcomp_1M_zstd12_patched
summary: 39.8 GiByte in 48.6sec - average of 839 MiB/s
$ sudo zfs list -p -o name,used,lused,ratio evenfaster/lowcomp_1M_zstd12_normal evenfaster/lowcomp_1M_zstd12_patched
NAME USED LUSED RATIO
evenfaster/lowcomp_1M_zstd12_normal 39549931520 42721221632 1.08
evenfaster/lowcomp_1M_zstd12_patched 39626399744 42721217536 1.07
$ python3 -c "print(39626399744 - 39549931520)"
76468224
$
I'll take 76 MB out of 42 GB for > 4x speedup.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#13244
We want `zpool import` to be highly robust and never panic, even
when encountering corrupt metadata. This is already handled in the
arc_read() code path, which covers most cases, but spa_load_verify_cb()
relies on zio_read() and is responsible for verifying the block pointer.
During import it is also possible to encounter blocks pointers which
contain ZIO_COMPRESS_INHERIT and ZIO_CHECKSUM_INHERIT values. Relax
the verification function slightly to allow this.
Futhermore, extend dsl_scan_recurse() to verify the block pointer
contents of level zero blocks which are not of type DMU_OT_DNODE or
DMU_OT_OBJSET. This is handled by arc_read() in the other cases.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13124Closes#13360
There are times when end-users may wish to have
a fast and convenient method to get zpool guid
without having to use libzfs. This commit
exposes the zpool guid via kstats in similar
manner to the zpool state.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andrew Walker <awalker@ixsystems.com>
Closes#13466
Recognise initial whitespace, + in both cases,
and - also in unsigneds
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13434
clang-15 emits the following error message for functions without
a prototype:
fs/zfs/os/linux/spl/spl-kmem-cache.c:1423:27: error:
a function declaration without a prototype is deprecated
in all versions of C [-Werror,-Wstrict-prototypes]
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Aidan Harris <me@aidanharr.is>
Closes#13421
I genuinely don't know why this didn't come up before,
but adding the LZ4 early abort pointed out this flaw,
in which we're allocating a buffer of one size, and
then telling the compressor that we're handing it buffers
of a different size, which may be Very Different - say,
allocating 512b and then telling it the inputs are 128k.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Amanakis <gamanakis@gmail.com>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#13375
When calculating mg_aliquot alike to #12046 use number of unique data
disks in the vdev, not the total number of children vdev. Increase
default value of the tunable from 512KB to 1MB to compensate.
Before this change each disk in striped pool was getting 512KB of
sequential data, in 2-wide mirror -- 1MB, in 3-wide RAIDZ1 -- 768KB.
After this change in all the cases each disk should get 1MB.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#13388
Holding a dbuf is a common operation which can become highly contended
in dbuf_find() when acquiring the dbuf hash mutex. This is particularly
true on Linux when reading/writing volumes since by default up to 32
threads from the zvol_taskq may be taking a hold of the same dbuf.
This should also be observable on FreeBSD as long as there are enough
processes accessing the volume concurrently.
This is further aggregrated by the fact that only the block id will
be unique when calculating the dbuf hash for a single volume. The
objset id, object id, and level will be the same for data blocks.
This has been observed to result in a somehwat less than uniform hash
distribution and a longer than expected max hash chain depth (~20)
on a large memory system (256 GB) using volumes.
This commit improves the siutation by switching the hash mutex to
an rwlock to allow concurrent lookups, and increasing DBUF_RWLOCKS
from 2048 to 8192 to further reduce the odds of a hash collision.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13405
Page writebacks with WB_SYNC_NONE can take several seconds to complete
since they wait for the transaction group to close before being
committed. This is usually not a problem since the caller does not
need to wait. However, if we're simultaneously doing a writeback
with WB_SYNC_ALL (e.g via msync), the latter can block for several
seconds (up to zfs_txg_timeout) due to the active WB_SYNC_NONE
writeback since it needs to wait for the transaction to complete
and the PG_writeback bit to be cleared.
This commit deals with 2 cases:
- No page writeback is active. A WB_SYNC_ALL page writeback starts
and even completes. But when it's about to check if the PG_writeback
bit has been cleared, another writeback with WB_SYNC_NONE starts.
The sync page writeback ends up waiting for the non-sync page
writeback to complete.
- A page writeback with WB_SYNC_NONE is already active when a
WB_SYNC_ALL writeback starts. The WB_SYNC_ALL writeback ends up
waiting for the WB_SYNC_NONE writeback.
The fix works by carefully keeping track of active sync/non-sync
writebacks and committing when beneficial.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Shaan Nobee <sniper111@gmail.com>
Closes#12662Closes#12790
Commit 361a7e8 (log xattr=sa create/remove/update to ZIL) introduced a
TX_SETSAXATTR, but missed to add a corresponding entry in
zvol_replay_vector. Adding a missing replay entry in zvol_replay_vector.
Reviewed-by: Christian Schwarz <christian.schwarz@nutanix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jitendra Patidar <jitendra.patidar@nutanix.com>
Closes#13396Closes#13395
Increase the default allowed maximum recordsize from 1M to 16M.
As described in the zfs(4) man page, there are significant costs
which need to be considered before using very large blocks.
However, there are scenarios where they make good sense and
it should no longer be necessary to artificially restrict their
use behind a module option.
Note that for 32-bit platforms we continue to leave this
restriction in place due to the limited virtual address space
available (256-512MB). On these systems only a handful
of blocks could be cached at any one time severely impacting
performance and potentially stability.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12830Closes#13302
Previous flushing algorithm limited only total number of log blocks to
the minimum of 256K and 4x number of metaslabs in the pool. As result,
system with 1500 disks with 1000 metaslabs each, touching several new
metaslabs each TXG could grow spacemap log to huge size without much
benefits. We've observed one of such systems importing pool for about
45 minutes.
This patch improves the situation from five sides:
- By limiting maximum period for each metaslab to be flushed to 1000
TXGs, that effectively limits maximum number of per-TXG spacemap logs
to load to the same number.
- By making flushing more smooth via accounting number of metaslabs
that were touched after the last flush and actually need another flush,
not just ms_unflushed_txg bump.
- By applying zfs_unflushed_log_block_pct to the number of metaslabs
that were touched after the last flush, not all metaslabs in the pool.
- By aggressively prefetching per-TXG spacemap logs up to 16 TXGs in
advance, making log spacemap load process for wide HDD pool CPU-bound,
accelerating it by many times.
- By reducing zfs_unflushed_log_block_max from 256K to 128K, reducing
single-threaded by nature log processing time from ~10 to ~5 minutes.
As further optimization we could skip bumping ms_unflushed_txg for
metaslabs not touched since the last flush, but that would be an
incompatible change, requiring new pool feature.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12789
Currently, determining which datasets are affected by corruption is
a manual process.
The primary difficulty in reporting the list of affected snapshots is
that since the error was initially found, the snapshot where the error
originally occurred in, may have been deleted. To solve this issue, we
add the ID of the head dataset of the original snapshot which the error
was detected in, to the stored error report. Then any time a filesystem
is deleted, the errors associated with it are deleted as well. Any time
a clone promote occurs, we modify reports associated with the original
head to refer to the new head. The stored error reports are identified
by this head ID, the birth time of the block which the error occurred
in, as well as some information about the error itself are also stored.
Once this information is stored, we can find the set of datasets
affected by an error by walking back the list of snapshots in the given
head until we find one with the appropriate birth txg, and then traverse
through the snapshots of the clone family, terminating a branch if the
block was replaced in a given snapshot. Then we report this information
back to libzfs, and to the zpool status command, where it is displayed
as follows:
pool: test
state: ONLINE
status: One or more devices has experienced an error resulting in data
corruption. Applications may be affected.
action: Restore the file in question if possible. Otherwise restore the
entire pool from backup.
see: https://openzfs.github.io/openzfs-docs/msg/ZFS-8000-8A
scan: scrub repaired 0B in 00:00:00 with 800 errors on Fri Dec 3
08:27:57 2021
config:
NAME STATE READ WRITE CKSUM
test ONLINE 0 0 0
sdb ONLINE 0 0 1.58K
errors: Permanent errors have been detected in the following files:
test@1:/test.0.0
/test/test.0.0
/test/1clone/test.0.0
A new feature flag is introduced to mark the presence of this change, as
well as promotion and backwards compatibility logic. This is an updated
version of #9175. Rebase required fixing the tests, updating the ABI of
libzfs, updating the man pages, fixing bugs, fixing the error returns,
and updating the old on-disk error logs to the new format when
activating the feature.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Co-authored-by: TulsiJain <tulsi.jain@delphix.com>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#9175Closes#12812
Originally it was thought it would be useful to split up the kmods
by functionality. This would allow external consumers to only load
what was needed. However, in practice we've never had a case where
this functionality would be needed, and conversely managing multiple
kmods can be awkward. Therefore, this change merges all but the
spl.ko kmod in to a single zfs.ko kmod.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13274
These are displayed as the descriptions of the sysctl's on FreeBSD
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Closes#13334
An earlier commit introduces AT_MODE into the shared kernel sources,
instead of the preferred existing ATTR_MODE use.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Signed-off-by: Jorgen lundman <lundman@lundman.net>
Closes#13293
Parts of the Linux kernel build system struggle with _Noreturn. This
results in the following warnings when building on RHEL 8.5, and likely
other environments. Switch to using the __attribute__((noreturn)).
warning: objtool: dbuf_free_range()+0x2b8:
return with modified stack frame
warning: objtool: dbuf_free_range()+0x0:
stack state mismatch: cfa1=7+40 cfa2=7+8
...
WARNING: EXPORT symbol "arc_buf_size" [zfs.ko] version generation
failed, symbol will not be versioned.
WARNING: EXPORT symbol "spa_open" [zfs.ko] version generation
failed, symbol will not be versioned.
...
Additionally, __thread_exit() has been renamed spl_thread_exit() and
made a static inline function. This was needed because the kernel
will generate a warning for symbols which are __attribute__((noreturn))
and then exported with EXPORT_SYMBOL.
While we could continue to use _Noreturn in user space I've also
switched it to __attribute__((noreturn)) purely for consistency
throughout the code base.
Reviewed-by: Ryan Moeller <freqlabs@FreeBSD.org>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13238
This explodes as -Wunused-variable on GCC 8.5.0, despite it being used,
just not in an evaluated context
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Ryan Moeller <freqlabs@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13195
bcopy() has a confusing argument order and is actually a move, not a
copy; they're all deprecated since POSIX.1-2001 and removed in -2008,
and we shim them out to mem*() on Linux anyway
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12996
Caught by UBSAN: ZI_NO_DVA is passed explicitly in
zio_handle_decrypt_injection() and can be an ENOENT from zio_match_dva()
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Damian Szuberski <szuberskidamian@gmail.com>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13146Closes#13190
Add physical device size/capacity only for physical devices in
'zpool list -v' instead of displaying "-" in the SIZE column.
This would make it easier to see the individual device capacity and
to determine which spares are large enough to replace which devices.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Dipak Ghosh <dipak.ghosh@hpe.com>
Signed-off-by: Akash B <akash-b@hpe.com>
Closes#12561Closes#13106
When unlinking multiple files from a pool at 100% capacity, it was
possible for ENOSPC to be returned after the first unlink. e.g.
rm -f /mnt/fs/test1.0.0 /mnt/fs/test1.1.0 /mnt/fs/test1.2.0
rm: cannot remove '/mnt/fs/test1.1.0': No space left on device
rm: cannot remove '/mnt/fs/test1.2.0': No space left on device
After waiting for the pending deferred frees from the first unlink to
be processed the remaining files can then be unlinked. This is caused
by the quota limit in dsl_dir_tempreserve_impl() being temporarily
decreased to the allocatable pool capacity less any deferred free
space.
This is resolved using the existing mechanism of returning ERESTART
when over quota as long as we know enough space will shortly be
available after processing the pending deferred frees.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <freqlabs@FreeBSD.org>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13172
A function that returns with no value is a different thing from a
function that doesn't return at all. Those are two orthogonal
concepts, commonly confused.
pthread_create(3) expects a pointer to a start routine that has a
very precise prototype:
void *(*start_routine)(void *);
However, other thread functions, such as kernel ones, expect:
void (*start_routine)(void *);
Providing a different one is incorrect, and has only been working
because the ABIs happen to produce a compatible function.
We should use '_Noreturn void', since it's the natural type, and
then provide a '_Noreturn void *' wrapper for pthread functions.
For consistency, replace most cases of __NORETURN or
__attribute__((noreturn)) by _Noreturn. _Noreturn is understood
by -std=gnu89, so it should be safe to use everywhere.
Ref: https://github.com/openzfs/zfs/pull/13110#discussion_r808450136
Ref: https://software.codidact.com/posts/285972
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Signed-off-by: Alejandro Colomar <alx.manpages@gmail.com>
Closes#13120
As such, there are no specific synchronous semantics defined for
the xattrs. But for xattr=on, it does log to ZIL and zil_commit() is
done, if sync=always is set on dataset. This provides sync semantics
for xattr=on with sync=always set on dataset.
For the xattr=sa implementation, it doesn't log to ZIL, so, even with
sync=always, xattrs are not guaranteed to be synced before xattr call
returns to caller. So, xattr can be lost if system crash happens, before
txg carrying xattr transaction is synced.
This change adds xattr=sa logging to ZIL on xattr create/remove/update
and xattrs are synced to ZIL (zil_commit() done) for sync=always.
This makes xattr=sa behavior similar to xattr=on.
Implementation notes:
The actual logging is fairly straight-forward and does not warrant
additional explanation.
However, it has been 14 years since we last added new TX types
to the ZIL [1], hence this is the first time we do it after the
introduction of zpool features. Therefore, here is an overview of the
feature activation and deactivation workflow:
1. The feature must be enabled. Otherwise, we don't log the new
record type. This ensures compatibility with older software.
2. The feature is activated per-dataset, since the ZIL is per-dataset.
3. If the feature is enabled and dataset is not for zvol, any append to
the ZIL chain will activate the feature for the dataset. Likewise
for starting a new ZIL chain.
4. A dataset that doesn't have a ZIL chain has the feature deactivated.
We ensure (3) by activating on the first zil_commit() after the feature
was enabled. Since activating the features requires waiting for txg
sync, the first zil_commit() after enabling the feature will be slower
than usual. The downside is that this is really a conservative
approximation: even if we never append a 'TX_SETSAXATTR' to the ZIL
chain, we pay the penalty for feature activation. The upside is that the
user is in control of when we pay the penalty, i.e., upon enabling the
feature.
We ensure (4) by hooking into zil_sync(), where ZIL destroy actually
happens.
One more piece on feature activation, since it's spread across
multiple functions:
zil_commit()
zil_process_commit_list()
if lwb == NULL // first zil_commit since zil_open
zil_create()
if no log block pointer in ZIL header:
if feature enabled and not active:
// CASE 1
enable, COALESCE txg wait with dmu_tx that allocated the
log block
else // log block was allocated earlier than this zil_open
if feature enabled and not active:
// CASE 2
enable, EXPLICIT txg wait
else // already have an in-DRAM LWB
if feature enabled and not active:
// this happens when we enable the feature after zil_create
// CASE 3
enable, EXPLICIT txg wait
[1] da6c28aaf6
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Christian Schwarz <christian.schwarz@nutanix.com>
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Reviewed-by: Ryan Moeller <freqlabs@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jitendra Patidar <jitendra.patidar@nutanix.com>
Closes#8768Closes#9078
New `zfs_type_t` value `ZFS_TYPE_INVALID` is introduced.
Variable initialization is now possible to make GCC happy.
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: szubersk <szuberskidamian@gmail.com>
Closes#12167Closes#13103
Raw sending from pool1/encrypted with ashift=9 to pool2/encrypted with
ashift=12 results to failure when mounting pool2/encrypted (Input/Output
error). Notably, the opposite, raw sending from a greater ashift to a
lower one does not fail.
This happens because zio_compress_write() falsely checks only
ZIO_FLAG_RAW_COMPRESS and not ZIO_FLAG_RAW_ENCRYPT which is also set in
encrypted raw send streams. In this case it rounds up the psize and if
not equal to the zio->io_size it modifies the block by zeroing out
the extra bytes. Because this happens in a SA attr. registration object
(type=46), the decryption fails upon mounting the filesystem, and zpool
status falsely reports an error.
Fix this by checking both ZIO_FLAG_RAW_COMPRESS and ZIO_FLAG_RAW_ENCRYPT
before deciding whether to zero-pad a block.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#13067Closes#13074
It's the only one actually used
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12901
Add hooks for when spa is created, exported, activated and
deactivated. Used by macOS to attach iokit, and lock
kext as busy (to stop unloads).
Userland, Linux, and, FreeBSD have empty stubs.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Closes#12801
There are two codepaths than can dirty final TXGs:
1) If calling spa_export_common()->spa_unload()->
spa_unload_log_sm_flush_all() after the spa_final_txg is set, then
spa_sync()->spa_flush_metaslabs() may end up dirtying the final
TXGs. Then we have the following panic:
Call Trace:
<TASK>
dump_stack_lvl+0x46/0x62
spl_panic+0xea/0x102 [spl]
dbuf_dirty+0xcd6/0x11b0 [zfs]
zap_lockdir_impl+0x321/0x590 [zfs]
zap_lockdir+0xed/0x150 [zfs]
zap_update+0x69/0x250 [zfs]
feature_sync+0x5f/0x190 [zfs]
space_map_alloc+0x83/0xc0 [zfs]
spa_generate_syncing_log_sm+0x10b/0x2f0 [zfs]
spa_flush_metaslabs+0xb2/0x350 [zfs]
spa_sync_iterate_to_convergence+0x15a/0x320 [zfs]
spa_sync+0x2e0/0x840 [zfs]
txg_sync_thread+0x2b1/0x3f0 [zfs]
thread_generic_wrapper+0x62/0xa0 [spl]
kthread+0x127/0x150
ret_from_fork+0x22/0x30
</TASK>
2) Calling vdev_*_stop_all() for a second time in spa_unload() after
spa_export_common() unnecessarily delays the final TXGs beyond what
spa_final_txg is set at.
Fix this by performing the check and call for
spa_unload_log_sm_flush_all() before the spa_final_txg is set in
spa_export_common(). Also check if the spa_final_txg has already been
set in spa_unload() and skip those calls in this case.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
External-issue: https://www.illumos.org/issues/9081Closes#13048Closes#13098
Unfortunately macOS has obj-C keyword "fallthrough" in the OS headers.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Damian Szuberski <szuberskidamian@gmail.com>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Closes#13097
On newer compilers, dsl_dataset.c now warns (or, on DEBUG, errors)
on uninitialized variable usage.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#13083
dmu_recv_begin_check() unconditionally sets the DS_HOLD_FLAG_DECRYPT
flag before calling dsl_dataset_hold_flags(). If the key on the
receiving side isn't loaded or the send stream contains embedded
blocks, the receive check fails for a stream which is perfectly
valid and could be received without any problem. This seems like
a remnant of the initial design, where unencrypted datasets below
encrypted ones weren't allowed.
Add a condition to set `DS_HOLD_FLAG_DECRYPT` only for encrypted
datasets, modify an existing test to detect this regression and add
a test for raw replication streams.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Amanakis <gamanakis@gmail.com>
Co-authored-by: George Amanakis <gamanakis@gmail.com>
Signed-off-by: Attila Fülöp <attila@fueloep.org>
Closes#13033Closes#13076
All of these externs are already #included as static inline
functions via corresponding headers.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@gmail.com>
Closes#13073
There's no need to make the platform ops dynamic dispatch.
This change replaces the dynamic dispatch with static calls to the
platform-specific functions.
To avoid name collisions, prefix all platform-specific functions
with `zvol_os_`.
I actually find `zvol_..._os` slightly nicer to read in the calling
code, but having it as a prefix is useful.
Advantage:
- easier jump-to-definition / grepping
- potential benefits to static analysis
- better legibility
Future work: also prefix remaining `static` functions in zvol_os.c.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Christian Schwarz <christian.schwarz@nutanix.com>
Closes#12965
Use error thresholds from policy to control whether to scrub data
and/or metadata. If threshold is set to UINT64_MAX, then caller
probably does not care about result and we may skip that part.
By default import neither set the data error threshold nor read
the error counter, so skip the data scrub for faster import.
Metadata are still scrubbed and fail if even single error found.
While there just for symmetry return number of metadata errors in
case threshold is not set to zero and we haven't reached it.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#13022
The following commit moved the users of `deferred` into function
dsl_pool_unreserved_space:
commit d2734cce68
Author: Serapheim Dimitropoulos <serapheim.dimitro@delphix.com>
Date: Fri Dec 16 14:11:29 2016 -0800
OpenZFS 9166 - zfs storage pool checkpoint
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <freqlabs@FreeBSD.org>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Christian Schwarz <christian.schwarz@nutanix.com>
Closes#13056
POSIX requires that set-uid and set-gid bits to be removed when an
unprivileged user writes to a file and ZFS does that during normal
operation.
The problem arrises when the write is stored in the ZIL and replayed.
During replay we have no access to original credentials of the process
doing the write, so zfs_write() will be performed with the root
credentials. When root is doing the write set-uid and set-gid bits
are not removed from the file.
To correct that, log a separate TX_SETATTR entry that removed those bits
on first write to such file.
Idea from: Christian Schwarz
Add test for ZIL replay of setuid/setgid clearing.
Improve various edge cases when clearing setid bits:
- The setid bits can be readded during a single write, so make sure to check
for them on every chunk write.
- Log TX_SETATTR record at most once per transaction group (if the setid bits
are keep coming back).
- Move zfs_log_setattr() outside of zp->z_acl_lock.
Reviewed-by: Dan McDonald <danmcd@joyent.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Christian Schwarz <me@cschwarz.com>
Signed-off-by: Pawel Jakub Dawidek <pawel@dawidek.net>
Closes#13027
`configure` now accepts `--enable-asan` and `--enable-ubsan` switches
which results in passing `-fsanitize=address`
and `-fsanitize=undefined`, respectively, to the compiler. Those
flags are enabled in GitHub workflows for ZTS and zloop. Errors
reported by both instrumentations are corrected, except for:
- Memory leak reporting is (temporarily) suppressed. The cost of
fixing them is relatively high compared to the gains.
- Checksum computing functions in `module/zcommon/zfs_fletcher*`
have UBSan errors suppressed. It is completely impractical
to enforce 64-byte payload alignment there due to performance
impact.
- There's no ASan heap poisoning in `module/zstd/lib/zstd.c`. A custom
memory allocator is used there rendering that measure
unfeasible.
- Memory leaks detection has to be suppressed for `cmd/zvol_id`.
`zvol_id` is run by udev with the help of `ptrace(2)`. Tracing is
incompatible with memory leaks detection.
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: szubersk <szuberskidamian@gmail.com>
Closes#12928
In files created/modified before 4254acb there may be a corruption of
xattrs which is not reported during scrub and normal send/receive. It
manifests only as an error when raw sending/receiving. This happens
because currently only the raw receive path checks for discrepancies
between the dnode bonus length and the spill pointer flag.
In case we encounter a dnode whose bonus length is greater than the
predicted one, we should report an error. Modify in this regard
dnode_sync() with an assertion at the end, dump_dnode() to error out,
dsl_scan_recurse() to report errors during a scrub, and zstream to
report a warning when dumping. Also added a test to verify spill blocks
are sent correctly in a raw send.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#12720Closes#13014
69 CSTYLED BEGINs remain, appx. 30 of which can be removed if cstyle(1)
had a useful policy regarding
CALL(ARG1,
ARG2,
ARG3);
above 2 lines. As it stands, it spits out *both*
sysctl_os.c: 385: continuation line should be indented by 4 spaces
sysctl_os.c: 385: indent by spaces instead of tabs
which is very cool
Another >10 could be fixed by removing "ulong" &al. handling.
I don't foresee anyone actually using it intentionally
(does it even exist in modern headers? why did it in the first place?).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12993
FreeBSD's implementation of zfs_uio_fault_move() returns EFAULT when a
page fault occurs while copying data in or out of user buffers. The VFS
treats such errors specially and will retry the I/O operation (which may
have made some partial progress).
When the FreeBSD and Linux implementations of zfs_write() were merged,
the handling of errors from dmu_write_uio_dbuf() changed such that
EFAULT is not handled as a partial write. For example, when appending
to a file, the z_size field of the znode is not updated after a partial
write resulting in EFAULT.
Restore the old handling of errors from dmu_write_uio_dbuf() to fix
this. This should have no impact on Linux, which has special handling
for EFAULT already.
Reviewed-by: Andriy Gapon <avg@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#12964
Raw receiving a snapshot back to the originating dataset is currently
impossible because of user accounting being present in the originating
dataset.
One solution would be resetting user accounting when raw receiving on
the receiving dataset. However, to recalculate it we would have to dirty
all dnodes, which may not be preferable on big datasets.
Instead, we rely on the os_phys flag
OBJSET_FLAG_USERACCOUNTING_COMPLETE to indicate that user accounting is
incomplete when raw receiving. Thus, on the next mount of the receiving
dataset the local mac protecting user accounting is zeroed out.
The flag is then cleared when user accounting of the raw received
snapshot is calculated.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#12981Closes#10523Closes#11221Closes#11294Closes#12594
Issue #11300
When the eviction thread goes to shrink an ARC state, it allocates a set
of marker buffers used to hold its place in the state's sublists.
This can be problematic in low memory conditions, since
1) the allocation can be substantial, as we allocate NCPU markers;
2) on at least FreeBSD, page reclamation can block in
arc_wait_for_eviction()
In particular, in stress tests it's possible to hit a deadlock on
FreeBSD when the number of free pages is very low, wherein the system is
waiting for the page daemon to reclaim memory, the page daemon is
waiting for the ARC eviction thread to finish, and the ARC eviction
thread is blocked waiting for more memory.
Try to reduce the likelihood of such deadlocks by pre-allocating markers
for the eviction thread at ARC initialization time. When evicting
buffers from an ARC state, check to see if the current thread is the ARC
eviction thread, and use the pre-allocated markers for that purpose
rather than dynamically allocating them.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: George Amanakis <gamanakis@gmail.com>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#12985
Evaluated every variable that lives in .data (and globals in .rodata)
in the kernel modules, and constified/eliminated/localised them
appropriately. This means that all read-only data is now actually
read-only data, and, if possible, at file scope. A lot of previously-
global-symbols became inlinable (and inlined!) constants. Probably
not in a big Wowee Performance Moment, but hey.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12899
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Mark Maybee <mark.maybee@delphix.com>
Closes#12951
There should be no risk of us accidentally hitting this since
we'd need maliciously malformed data to wind up in the pipeline,
or a very unfortunate random bit flip at exactly the right moment.
Still since we can handle it we should.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Adam Moss <c@yotes.com>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12947
As an experiment, I stole the lz4 decompressor from
upstream lz4 (1.9.3), and landed it.
Feedback suggested that keeping the vendor lz4 code isolated and
unlinted was probably reasonable, so I lobbed it into its own file.
It also seemed reasonable to put the mostly-untouched* code into
lz4.c proper, and relegate the integrated and ZFS-specific code to
lz4_zfs.c.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12805
Probably introduced inadvertently in b525630 (Native Encryption).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Amanakis <gamanakis@gmail.com>
Signed-off-by: Christian Schwarz <christian.schwarz@nutanix.com>
Closes#12935
This reverts commit f6a0dac84a.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#12938
Verify that all empty sectors are zero filled before using them to
calculate parity. Failure to do so can result in incorrect parity
columns being generated and written to disk if the contents of an
empty sector are non-zero. This was possible because the checksum
only protects the data portions of the buffer, not the empty sector
padding.
This issue has been addressed by updating raidz_parity_verify() to
check that all dRAID empty sectors are zero filled. Any sectors
which are non-zero will be fixed, repair IO issued, and a checksum
error logged. They can then be safely used to verify the parity.
This specific type of damage is unlikely to occur since it requires
a disk to have silently returned bad data, for an empty sector, while
performing a scrub. However, if a pool were to have been damaged
in this way, scrubbing the pool with this change applied will repair
both the empty sector and parity columns as long as the data checksum
is valid. Checksum errors will be reported in the `zpool status`
output for any repairs which are made.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12857
On FreeBSD vnode reclamation is single-threaded, protected by single
global lock. Linux seems to be able to use a thread per mount point,
but at this time it creates more harm than good.
Reduce number of threads to 1, adding tunable in case somebody wants
to try more.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Chris Dunlop <chris@onthe.net.au>
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#12896
Issue #9966
If the fields to be listed and sorted by are constrained
to those populated by dsl_dataset_fast_stat(), then
zfs list is much faster, as it does not need to open each
objset and reads its properties.
A previous optimization by Pawel Dawidek
(0cee24064a) took advantage
of this to make listing snapshot names sorted only by name
much faster.
However, it was limited to `-o name -s name`, this work
extends this optimization to work with:
- name
- guid
- createtxg
- numclones
- inconsistent
- redacted
- origin
and could be further extended to any other properties
supported by dsl_dataset_fast_stat() or similar, that do
not require extra locking or reading from disk.
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Pawel Jakub Dawidek <pawel@dawidek.net>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Closes#11080
Improve the ability of zfs send to determine if a block is compressed
or not by using information contained in the blkptr.
Reviewed-by: Rich Ercolani <rincebrain@gmail.com>
Reviewed-by: Matthew Ahrens <matthew.ahrens@delphix.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#12770
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#12728
For my sins, I started running valgrind over ztest to try and fix
that pesky intermittent "zloop dies with malloc errors" problem.
This one seemed exciting enough to merit cutting a PR for before
the rest get polished.
Suggested-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12214
Due to a possible lock inversion the zvol open call path on Linux
needs to be able to retry in the case where the spa_namespace_lock
cannot be acquired.
For Linux 5.12 an older kernel this was accomplished by returning
-ERESTARTSYS from zvol_open() to request that blkdev_get() drop
the bdev->bd_mutex lock, reaquire it, then call the open callback
again. However, as of the 5.13 kernel this behavior was removed.
Therefore, for 5.12 and older kernels we preserved the existing
retry logic, but for 5.13 and newer kernels we retry internally in
zvol_open(). This should always succeed except in the case where
a pool's vdev are layed on zvols, in which case it may fail. To
handle this case vdev_disk_open() has been updated to retry when
opening a device when -ERESTARTSYS is returned.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #12301Closes#12759
Strict hole reporting was previously disabled by default as a
performance optimization. However, this has lead to confusion
over the expected behavior and a variety of workarounds being
adopted by consumers of ZFS. Change the default behavior to
always report holes and force the TXG sync.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12746
- Allocate ve_search on the stack, so we avoid allocating memory for
every I/O even if the VDEV cache is disabled.
- Reduce lock scope.
- Avoid locking in vdev_cache_read() when the VDEV cache is disabled.
- Sort file names properly.
- Correct comment.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Pawel Jakub Dawidek <pawel@dawidek.net>
Closes#12749
Add properties, similar to pool properties, to each vdev.
This makes use of the existing per-vdev ZAP that was added as
part of device evacuation/removal.
A large number of read-only properties are exposed,
many of the members of struct vdev_t, that provide useful
statistics.
Adds support for read-only "removing" vdev property.
Adds the "allocating" property that defaults to "on" and
can be set to "off" to prevent future allocations from that
top-level vdev.
Supports user-defined vdev properties.
Includes support for properties.vdev in SYSFS.
Co-authored-by: Allan Jude <allan@klarasystems.com>
Co-authored-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Closes#11711
The code is integrated, builds fine, runs fine, there's not really
any reason not to.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12735
Special allocation class or dedup vdevs may have roughly the same
performance as L2ARC vdevs. Introduce a new tunable to exclude those
buffers from being cacheable on L2ARC.
Reviewed-by: Don Brady <don.brady@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#11761Closes#12285
The l2cache device could be added twice because vdev_inuse() does not
check spa_l2cache for added devices. Make l2cache vdevs inuse checking
logic more closer to spare vdevs.
Reviewed-by: George Amanakis <gamanakis@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Fedor Uporov <fuporov.vstack@gmail.com>
Closes#9153Closes#12689
In addition to flushing memory mapped regions when checking holes,
commit de198f2d95 modified the dirty dnode detection logic to check
the dn->dn_dirty_records instead of the dn->dn_dirty_link. Relying
on the dirty record has not be reliable, switch back to the previous
method.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #11900Closes#12745
The only zdb utility require to read metaslab-related data during
read-only pool import because of spacemaps validation. Add global
variable which will allow zdb read spacemaps in case of readonly
import mode.
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Fedor Uporov <fuporov.vstack@gmail.com>
Closes#9095Closes#12687
In order to reduce contention on the vq_lock, optional skip sectors
for Raidz writes can be placed into a single IO request. This is done by
padding out the linear ABD for a parity column to contain the skip
sector and by creating gang ABD to contain the data and skip sector for
data columns.
The vdev_raidz_map_alloc() function now contains specific functions for
both reads and write to allocate the ABD's that will be issued down to
the VDEV chldren.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-By: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Brian Atkinson <batkinson@lanl.gov>
Closes#12333
When using lseek(2) to report data/holes memory mapped regions of
the file were ignored. This could result in incorrect results.
To handle this zfs_holey_common() was updated to asynchronously
writeback any dirty mmap(2) regions prior to reporting holes.
Additionally, while not strictly required, the dn_struct_rwlock is
now held over the dirty check to prevent the dnode structure from
changing. This ensures that a clean dnode can't be dirtied before
the data/hole is located. The range lock is now also taken to
ensure the call cannot race with zfs_write().
Furthermore, the code was refactored to provide a dnode_is_dirty()
helper function which checks the dnode for any dirty records to
determine its dirtiness.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Rich Ercolani <rincebrain@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #11900Closes#12724
It turns out that short-circuiting the EFAULT behavior on a short read
breaks things on FreeBSD. So until there's a nicer solution, let's
just revert the behavior for not-Linux.
Reference:
https://reviews.freebsd.org/R10:70f51f0e474ffe1fb74cb427423a2fba3637544d
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12698
If you've got multiple scrubs/resilvers going, it's rather helpful
to know which pool each scan line refers to.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes: #12674
The fnvlist versions of the functions are fatal if they fail,
saving each call from having to include checking the result.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Remove code duplication by moving code responsible for partial block
zeroing to a separate function: dnode_partial_zero().
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Pawel Jakub Dawidek <pawel@dawidek.net>
Closes#12627
Make the main dmu_buf_hold_array() function non-static.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Pawel Jakub Dawidek <pawel@dawidek.net>
Closes#12628
Lustre makes light use of the zfs_refcount interfaces which
isn't a problem when using a non-debug build of OpenZFS. However,
when debugging is enabled the required symbols are not exported.
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12613
refcount_add_many(foo,N) is not the same as
for (i=0; i < N; i++) { refcount_add(foo); }
Unfortunately, this is only actually true with debug kernels and
reference_tracking_enable=1.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12589Closes#12602
When you create a pool, zfs writes vd->vdev_enc_sysfs_path with the
enclosure sysfs path to the fault LEDs, like:
vdev_enc_sysfs_path = /sys/class/enclosure/0:0:1:0/SLOT8
However, this enclosure path doesn't get updated on successive imports
even if enclosure path to the disk changes. This patch fixes the issue.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#11950Closes#12095
Commit 0c03d21ac9 left in a redundant if condition while
removing some code. Just remove it.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Attila Fülöp <attila@fueloep.org>
Closes#12598
Currently, dmu_read_uio_dnode can read 64K of a requested 1M in one
loop, get EFAULT back from zfs_uiomove() (because the iovec only holds
64k), and return EFAULT, which turns into EAGAIN on the way out. EAGAIN
gets interpreted as "I didn't read anything", the caller tries again
without consuming the 64k we already read, and we're stuck.
This apparently works on newer kernels because the caller which breaks
on older Linux kernels by happily passing along a 1M read request and a
64k iovec just requests 64k at a time.
With this, we now won't return EFAULT if we got a partial read.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12370Closes#12509Closes#12516
In case an ARC buffer is allocated only on L2ARC, and there are
underlying errors in a pool with the cache device in faulty state, a
panic can occur in arc_read_done()->arc_hdr_destroy()->
arc_hdr_l2arc_destroy()->arc_hdr_clear_flags() when trying to free
the ARC buffer.
Fix this by discarding the buffer's identity in arc_hdr_destroy(), in
case the buffer is not empty, before calling arc_hdr_l2hdr_destroy().
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#12392
As of the Linux 5.9 kernel a fallthrough macro has been added which
should be used to anotate all intentional fallthrough paths. Once
all of the kernel code paths have been updated to use fallthrough
the -Wimplicit-fallthrough option will because the default. To
avoid warnings in the OpenZFS code base when this happens apply
the fallthrough macro.
Additional reading: https://lwn.net/Articles/794944/
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12441
Userland figures out which encryption-root keys are required to load,
and issues ZFS_IOC_LOAD_KEY.
The tail section of spa_keystore_load_wkey() will call
zvol_create_minors() on the encryption-root object.
Any clones of the encrypted zvol will not be plumbed. This commits
adds additional logic to detect if zvol has clones, and is encrypted,
then adds these to the list of zvols to call zvol_create_minors() on.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Closes#12471
Errors in zil_lwb_write_done() are not propagated to
zil_lwb_flush_vdevs_done() which can result in zil_commit_impl()
not returning an error to applications even when zfs was not able
to write data to the disk.
Remove the ZIO_FLAG_DONT_PROPAGATE flag from zio_rewrite() to
allow errors to propagate and consolidate the error handling for
flush and write errors to a single location (rather than having
error handling split between the "write done" and "flush done"
handlers).
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Prakash Surya <prakash.surya@delphix.com>
Signed-off-by: Arun KV <arun.kv@datacore.com>
Closes#12391Closes#12443
The block pointer verification check in arc_read() should also
cover embedded block pointers. While highly unlikely, accessing
a damaged block pointer can result in panic. To further harden
the code extend the existing check to include embedded block
pointers and add a comment explaining the rational for this
sanity check. Lastly, correct a flaw in zfs_blkptr_verify()
so the error count is checked even when checking a untrusted
config to verify the non-pool-specific portions of a block
pointer.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12535
For kernel to send snapshot mount/unmount events to zed.
For kernel to send symlink creates/removes on zvol plumbing.
(/dev/run/dsk/zvol/$pool/$zvol -> /dev/diskX)
If zed misses the ENODEV, all errors after are EINVAL. Treat any error
as kernel module failure.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Closes#12416
When zfs_send_corrupt_data is set, use the TRAVERSE_HARD flag,
so traverse_visitbp() will not fail with ECKSUM if a blockpointer
cannot be read, but rather will continue and send the objects it can.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Sponsored-By: Klara Inc.
Sponsored-By: WHC Online Solutions Inc.
Closes#12541
Unfortunately, there was an overzealous assertion that was (in pretty
specific circumstances) false, causing failure. This assertion was
added in error, so we're removing it.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#9897Closes#12020Closes#12246
We round up the psize to the nearest multiple of the asize or to the
lsize, whichever is smaller. Once that's done, we allocate a new
buffer of the appropriate size, zero the tail, and copy the data
into it. This adds a small performance cost to these kinds of writes,
but fixes the bookkeeping problems.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Co-authored-by: Matthew Ahrens <matthew.ahrens@delphix.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#12522Closes#8462
Previously, zpool-iostat did not display any data regarding rebuild I/Os
in either the latency/size histograms (-w/-l/-r) or the queue data (-q).
This fix essentially utilizes the existing infrastructure for tracking
rebuild queue data and displays this data in the proper places within
zpool-iostat's output.
Signed-off-by: Trevor Bautista <tbautista@newmexicoconsortium.org>
Signed-off-by: Trevor Bautista <tbautista@lanl.gov>
Co-authored-by: Trevor Bautista <tbautista@newmexicoconsortium.org>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
benchmark_raidz() allocates a row to benchmark parity calculation and
reconstruction. In the latter case, the parity blocks are left
uninitialized, leading to reports from KMSAN.
Initialize parity blocks to 0xAA as we do for the data earlier in the
function. This does not affect the selected RAID-Z implementation on
any of several systems tested.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#12473
When a header is allocated for full overwrite it is a waste of time
to allocate b_pabd/b_rabd for it, since arc_write() will free them
without ever being touched. If it is a read or a partial overwrite
then arc_read() and arc_hdr_decrypt() allocate them explicitly.
Reduced memory allocation in user threads also reduces ARC eviction
throttling there, proportionally increasing it in ZIO threads, that
is not good. To minimize or even avoid it introduce ARC allocation
reserve, allowing certain arc_get_data_abd() callers to allocate a
bit longer in situations where user threads will already throttle.
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12398
It is very expensive and not informative to call multilist_is_empty()
for each arc_change_state() on debug builds to check for impossible.
Instead implement special index function for arc_l2c_only->arcs_list,
multilists, panicking on any attempt to use it.
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12421
Instead of clearing stats inside arc_buf_alloc_impl() do it inside
arc_hdr_alloc() and arc_release(). It fixes statistics being wiped
every time a new dbuf is filled from the ARC.
Remove b_l1hdr.b_l2_hits. L2ARC hits are accounted at b_l2hdr.b_hits.
Since the hits are accounted under hash lock, replace atomics with
simple increments.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Wilson <george.wilson@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12422
vq_lock is already too congested for two more operations per I/O.
Instead of dropping and reacquiring it inside vdev_queue_aggregate()
delegate the zio_vdev_io_bypass() and zio_execute() calls for parent
I/Os to callers, that drop the lock any way to execute the new I/O.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12297
Use atomic_load_64() for zfs_refcount_count() to prevent torn reads
on 32-bit platforms. On 64-bit ones it should not change anything.
When built with ZFS_DEBUG but running without tracking enabled use
atomics instead of mutexes same as for builds without ZFS_DEBUG.
Since rc_tracked can't change live we can check it without lock.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12420
Before OpenZFS 2.0, trying to set the FreeBSD sysctl vfs.zfs.arc_max
to a disallowed value would return an error.
Since the switch, it instead only generates WARN_IF_TUNING_IGNORED
Keep the ability to set the sysctl's specifically to 0, even though
that is less than the minimum, because some tests depend on this.
Also lost, was the ability to set vfs.zfs.arc_max to a value less
than the default vfs.zfs.arc_min at boot time. Restore this as well.
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Closes#12161
Run arc_evict thread at higher priority, nice=0, to give it more CPU
time which can improve performance for workload with high ARC evict
activities.
On mixed read/write and sequential read workloads, I've seen between
10-40% better performance.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Tony Nguyen <tony.nguyen@delphix.com>
Closes#12397
It is wrong for arc_write_ready() to use zfs_abd_scatter_enabled to
decide whether to reallocate/copy the buffer, because the answer is
OS-specific and depends on the buffer size. Instead of that use
abd_size_alloc_linear(), moved into public header.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#12425
Commit 5dbf6c5a66 did not address these format specifier warnings
since they were introduced by an unrelated commit which had not
been rebased on 5dbf6c5a66 when merged. Fix them.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12435
In l2arc_add_vdev() first decide whether the device is eligible for
L2ARC rebuild or whole device trim and then add it to the list of cache
devices. Otherwise l2arc_feed_thread() might already start writing on
the device invalidating previous content as l2ad_hand = l2ad_start.
However l2arc_rebuild_vdev() needs the device present in the cache
device list to figure out its l2arc_dev_t. Fix this by moving most of
l2arc_rebuild_vdev() in a new function l2arc_rebuild_dev() which does
not need to search in the cache device list.
In contrast to l2arc_add_vdev() we do not have to worry about
l2arc_feed_thread() invalidating previous content when onlining a
cache device. The device parameters (l2ad*) are not cleared when
offlining the device and writing new buffers will not invalidate
all previous content. In worst case only buffers that have not had
their log block written to the device will be lost.
Retire persist_l2arc_00{4,5,8} tests since they cover code already
covered by the remaining ones. Test persist_l2arc_006 is renamed to
persist_l2arc_004 and persist_l2arc_007 is renamed to persist_l2arc_005.
Fix a typo in persist_l2arc_004, and remove an assertion that is not
always true from l2arc_arcstats_pos. Also update an assertion in
persist_l2arc_005 and explain why in a comment.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#12365
These were mostly used to annotate do {} while(0)s
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Issue #12201
This includes a simplification of mkbusy and format correctness in zhack
and ztest
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Issue #12201
It seems nothing ensures that this array is zeroed when a dnode is
freshly allocated, so in principle it retains the values from the
previous allocation. In practice it seems to be the case that the
fields should end up zeroed, but we can zero the field anyway for
consistency.
This was found using KMSAN.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#12383
When logging a TX_WRITE record in the case where file data has to be
copied from the DMU, we pad the log record size to a multiple of 8
bytes. In this case, any padding bytes should be zeroed, otherwise the
contents of uninitialized memory are written to the ZIL.
This was found using KMSAN.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#12383
When allocating a record, we round up the allocation size to a multiple
of 8. In this case, any padding bytes should be zeroed, otherwise the
contents of uninitialized memory are written to the ZIL.
This was found using KMSAN.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#12383
When logging TX_SETATTR, we could otherwise fail to initialize part of
the corresponding ZIL record depending on which fields are present in
the xvattr. Initialize the creation time and the AV scan timestamp to
zero so that uninitialized bytes are not written to the ZIL.
This was found using KMSAN.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#12383
spa_prop_find() may fail to find the specified property, in which case
it suppresses ENOENT from zap_lookup(). In this case, the return value
is left uninitialized, so spa_autoreplace was being initialized using an
uninitialized stack variable.
This was found using KMSAN. It appears to be a regression from commit
9eb7b46ed0, which removed the initialization of "autoreplace" from the
definition.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#12383
After 1325434b, we can in certain circumstances end up calling
spa_update_dspace with vd->vdev_mg NULL, which ends poorly during
vdev removal.
So let's not do that further space adjustment when we can't.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12380Closes#12428
Remove mc_lock use from metaslab_class_throttle_*(). The math there
is based on refcounts and so atomic, so the only race possible there
is between zfs_refcount_count() and zfs_refcount_add(). But in most
cases metaslab_class_throttle_reserve() is called with the allocator
lock held, which covers the race. In cases where the lock is not
held, GANG_ALLOCATION() or METASLAB_MUST_RESERVE are set, and so we
do not use zfs_refcount_count(). And even if we assume some other
non-existing scenario, the worst that may happen from this race is
few more I/Os get to allocation earlier, that is not a problem.
Move locks and data of different allocators into different cache
lines to avoid false sharing. Group spa_alloc_* arrays together
into single array of aligned struct spa_alloc spa_allocs. Align
struct metaslab_class_allocator.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Don Brady <don.brady@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12314
* Add Module Parameters Regarding Log Size Limit
zfs_wrlog_data_max
The upper limit of TX_WRITE log data. Once it is reached,
write operation is blocked, until log data is cleared out
after txg sync. It only counts TX_WRITE log with WR_COPIED
or WR_NEED_COPY.
Reviewed-by: Prakash Surya <prakash.surya@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: jxdking <lostking2008@hotmail.com>
Closes#12284
Remove unneeded global, practically constant, state pointer variables
(arc_anon, arc_mru, etc.), replacing them with macros of real state
variables addresses (&ARC_anon, &ARC_mru, etc.).
Change ARC_EVICT_ALL from -1ULL to UINT64_MAX, not requiring special
handling in inner loop of ARC reclamation. Respectively change bytes
argument of arc_evict_state() from int64_t to uint64_t.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#12348
Ensure all calls to bqueue_init() has a corresponding call to bqueue_destroy()
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Co-authored-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Closes#12118
* zio: avoid callback typecasting
* zil: avoid zil_itxg_clean() callback typecasting
* zpl: decouple zpl_readpage() into two separate callbacks
* nvpair: explicitly declare callbacks for xdr_array()
* linux/zfs_nvops: don't use external iput() as a callback
* zcp_synctask: don't use fnvlist_free() as a callback
* zvol: don't use ops->zv_free() as a callback for taskq_dispatch()
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Closes#12260
We don't use or need the pool name or value source in the zvol tasks.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#12361
Most of dsl_dir_diduse_space() and dsl_dir_transfer_space() CPU time
is a dd_lock overhead and time spent in dmu_buf_will_dirty(). Calling
them one after another is a waste of time and even more contention.
Doing that twice for each rewritten block within dbuf_write_done()
via dsl_dataset_block_kill() and dsl_dataset_block_born() created one
of the biggest CPU overheads in case of small blocks rewrite.
dsl_dir_diduse_transfer_space() combines functionality of these two
functions for cases where it is needed, but without double overhead,
practically for the cost of dsl_dir_diduse_space() or even cheaper.
While there, optimize dsl_dir_phys() calls in dsl_dir_diduse_space()
and dsl_dir_transfer_space(). It seems Clang detects some aliasing
there, repeating dd->dd_dbuf->db_data dereference multiple times,
increasing dd_lock scope and contention.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Author: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12300
