Create a kstat file which contains useful statistics about the
last N txgs processed. This can be helpful when analyzing pool
performance. The new KSTAT_TYPE_TXG type was added for this
purpose and it tracks the following statistics per-txg.
txg - Unique txg number
state - State (O)pen/(Q)uiescing/(S)yncing/(C)ommitted
birth; - Creation time
nread - Bytes read
nwritten; - Bytes written
reads - IOPs read
writes - IOPs write
open_time; - Length in nanoseconds the txg was open
quiesce_time - Length in nanoseconds the txg was quiescing
sync_time; - Length in nanoseconds the txg was syncing
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
During 'zpool import' all ZPOOL_CONFIG_PATH names are supposed
to be updated by fix_paths(). This was not happening for spare
and cache devices because the proper names were getting filtered
out of the pool_list_t->names. Interestingly, the names were
being filtered because the spare and cache devices do not
contain the pool name in their vdev label.
The fix is to exclude the device path from the list only if:
1) has a valid ZPOOL_CONFIG_POOL_NAME key in the label, and
2) that pool name does not match the specified pool name.
Since the label is valid and because it does properly store the
vdev guid it will be correctly assembled without the pool name.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#725
The 'zpool replace' command would fail when given a short name
because unlike on other platforms the short name cannot be
deterministically expanded to a single path. Multiple path
prefixes must be checked and in addition the partition suffix
for whole disks is determined by the prefix.
To handle this complexity a zfs_strcmp_pathname() function was
added which takes either a short or fully qualified device name.
Short names will be expanded using the prefixes in the default
import search path, or the ZPOOL_IMPORT_PATH environment variable
if it's defined. All posible expansions are then compared against
the comparison path. Care is taken to strip redundant slashes to
ensure legitimate matches are not missed.
In the context of this work the existing zfs_resolve_shortname()
function was extended to consider the ZPOOL_IMPORT_PATH when set.
The zfs_append_partition() interface was also simplified to take
only a single buffer.
The vast majority of these changes rework existing Linux specific
code which was originally written to accomidate udev. However,
there is some minimal cleanup which removes Illumos specific code.
This was done to improve readability but the basic flow and intent
of the upstream code was maintained.
These changes are the logical conclusion of the previos work to
adjust the 'zpool import' search behavior, see commit 44867b6a.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#544Closes#976
Both the SPL and the ZFS libspl export most of the atomic_* functions,
except atomic_sub_* functions which are only exported by the SPL, not by
libspl. This patch remedies that by implementing atomic_sub_* functions
in libspl.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #1013
illumos/illumos-gate@2e2c135528
Illumos changeset: 13780:6da32a929222
3100 zvol rename fails with EBUSY when dirty
Reviewed by: Christopher Siden <chris.siden@delphix.com>
Reviewed by: Adam H. Leventhal <ahl@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Garrett D'Amore <garrett@damore.org>
Approved by: Eric Schrock <eric.schrock@delphix.com>
Ported-by: Etienne Dechamps <etienne.dechamps@ovh.net>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#995
Currently, thread_create(), when called in userspace, creates a
joinable (i.e. not detached thread). This is the pthread default.
Unfortunately, this does not reproduce kthreads behavior (kthreads
are always detached). In addition, this contradicts the original
Solaris code which creates userspace threads in detached mode.
These joinable threads are never joined, which leads to a leakage of
pthread thread objects ("zombie threads"). This in turn results in
excessive ressource consumption, and possible ressource exhaustion in
extreme cases (e.g. long ztest runs).
This patch fixes the issue by creating userspace threads in detached
mode. The only exception is ztest worker threads which are meant to be
joinable.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #989
Introduced by commit 44867b6d6e.
We should of course check to ensure best isn't NULL before
attempting to dereference it.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#974
The goal of this change is to make 'zpool import' prefer to use
the peristent /dev/mapper or /dev/disk/by-* paths. These are far
preferable to the devices in /dev/ whos names are not persistent
and are determined by the order in which a device is detected.
This patch improves things by changing the default search path from
just to the top level /dev/ directory to (in order):
/dev/disk/by-vdev - Custom rules, use first if they exist
/dev/disk/zpool - Custom rules, use first if they exist
/dev/mapper - Use multipath devices before components
/dev/disk/by-uuid - Single unique entry and persistent
/dev/disk/by-id - May be multiple entries and persistent
/dev/disk/by-path - Encodes physical location and persistent
/dev/disk/by-label - Custom persistent labels
/dev - UNSAFE device names will change
The default search path can be overriden by setting the
ZPOOL_IMPORT_PATH environment variable. This must be a colon
delimited list of paths which are searched for vdevs. If the
'zpool import -d' option is specified only those listed paths
will be searched.
Finally, when multiple paths to the same device are found. If one
of the paths is an exact match for the path used last time to import
the pool it will be used. When there are no exact matches the
prefered path will be determined by the provided search order.
This means you can still import a pool and force specific names by
providing the -d <path> option. And the prefered names will persist
as long as those paths exist on your system.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#965
Delay executing exportfs command until its results are actually
required.
Signed-off-by: Cyril Plisko <cyril.plisko@mountall.com>
Signed-off-by: Gunnar Beutner <gunnar@beutner.name>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
In 1e33ac1e26, the maximum stack size for
userspace tools was set to 8k to mimic the available kernel stack size.
Unfortunately, due to differences in how the stack is used in userspace
vs kernel space, spurious stack overflows could occur in userspace
tools due to the limited stack size. This is especially true in ztest
when debugging is enabled.
This patch multiplies the userspace stack size by 4, which fixes the
stack overflow issues. This comes at the price of not being able to
catch stack size issues in userspace, but the previous solution proved
unreliable anyway.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Fixes#934.
Commit 858219c makes more sense down below in the 'if (verbose)'
section of the code. Initially, buf and path will never point
to the same location. Once 'path = buf' is set on a raidz vdev,
the code may drop into the verbose section depending on the
verbose flag. In here, using a tmpbuf makes sense since now
'buf == path'.
This issue does not occur in the upstream Solaris code because
their implementations of snprintf() allow for buf and path to
be the same address.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#57
Remove all of the generated autotools products from the repository
and update the .gitignore files accordingly.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#718
1796 "ZFS HOLD" should not be used when doing "ZFS SEND" from a read-only pool
2871 support for __ZFS_POOL_RESTRICT used by ZFS test suite
2903 zfs destroy -d does not work
2957 zfs destroy -R/r sometimes fails when removing defer-destroyed snapshot
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Approved by: Eric Schrock <Eric.Schrock@delphix.com>
References:
https://www.illumos.org/issues/1796https://www.illumos.org/issues/2871https://www.illumos.org/issues/2903https://www.illumos.org/issues/2957
Ported by: Martin Matuska <martin@matuska.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matt Ahrens <matt@delphix.com>
Reviewed by: George Wilson <George.Wilson@delphix.com>
Reviewed by: Bill Pijewski <wdp@joyent.com>
Reviewed by: Richard Elling <richard.elling@richardelling.com>
Approved by: Richard Lowe <richlowe@richlowe.net>
References:
https://www.illumos.org/issues/2635
Ported by: Martin Matuska <martin@matuska.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#717
This regression was accidentally introduced by commit
330d06f90d due to ZoL
specific code. The fix is to simply ensure the passed
nvlist is initialized and freed.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#876
Reviewed by: George Wilson <gwilson@zfsmail.com>
Reviewed by: Eric Schrock <eric.schrock@delphix.com>
Approved by: Richard Lowe <richlowe@richlowe.net>
References:
https://www.illumos.org/issues/1693
Ported by: Martin Matuska <martin@matuska.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#678
Currently, zvols have a discard granularity set to 0, which suggests to
the upper layer that discard requests of arbirarily small size and
alignment can be made efficiently.
In practice however, ZFS does not handle unaligned discard requests
efficiently: indeed, it is unable to free a part of a block. It will
write zeros to the specified range instead, which is both useless and
inefficient (see dnode_free_range).
With this patch, zvol block devices expose volblocksize as their discard
granularity, so the upper layer is aware that it's not supposed to send
discard requests smaller than volblocksize.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#862
1644 add ZFS "clones" property
1645 add ZFS "written" and "written@..." properties
1646 "zfs send" should estimate size of stream
1647 "zfs destroy" should determine space reclaimed by
destroying multiple snapshots
1708 adjust size of zpool history data
References:
https://www.illumos.org/issues/1644https://www.illumos.org/issues/1645https://www.illumos.org/issues/1646https://www.illumos.org/issues/1647https://www.illumos.org/issues/1708
This commit modifies the user to kernel space ioctl ABI. Extra
care should be taken when updating to ensure both the kernel
modules and utilities are updated. This change has reordered
all of the new ioctl()s to the end of the list. This should
help minimize this issue in the future.
Reviewed by: Richard Lowe <richlowe@richlowe.net>
Reviewed by: George Wilson <gwilson@zfsmail.com>
Reviewed by: Albert Lee <trisk@opensolaris.org>
Approved by: Garrett D'Amore <garret@nexenta.com>
Ported by: Martin Matuska <martin@matuska.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#826Closes#664
When libzfs checks if the module is loaded or not, it currently reads
/proc/modules and searches for a line matching the module name.
Unfortunately, if the module is included in the kernel itself (built-in
module), then /proc/modules won't list it, so libzfs will wrongly conclude
that the module is not loaded, thus making all ZFS userspace tools unusable.
Fortunately, all loaded modules appear as directories in /sys/module, even
built-in ones. Thus we can use /sys/module in lieu of /proc/modules to fix
the issue.
As a bonus, the code for checking becomes much simpler.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #851
The end_writeback() function was changed by moving the call to
inode_sync_wait() earlier in to evict(). This effecitvely changes
the ordering of the sync but it does not impact the details of
the zfs implementation.
However, as part of this change end_writeback() was renamed to
clear_inode() to reflect the new semantics. This change does
impact us and clear_inode() now maps to end_writeback() for
kernels prior to 3.5.
Signed-off-by: Richard Yao <ryao@cs.stonybrook.edu>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#784
The vmtruncate_range() support has been removed from the kernel in
favor of using the fallocate method in the file_operations table.
Signed-off-by: Richard Yao <ryao@cs.stonybrook.edu>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #784
The export_operations member ->encode_fh() has been updated to
take both the child and parent inodes. This interface used to
take the child dentry and a bool describing if the parent is needed.
NOTE: While updating this code I noticed that we do not currently
cleanly handle the case where we're passed a connectable parent.
This code should be audited to make sure we're doing the right thing.
Signed-off-by: Richard Yao <ryao@cs.stonybrook.edu>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #784
Currently, zpool online -e (dynamic vdev expansion) doesn't work on
whole disks because we're invoking ioctl(BLKRRPART) from userspace
while ZFS still has a partition open on the disk, which results in
EBUSY.
This patch moves the BLKRRPART invocation from the zpool utility to the
module. Specifically, this is done just before opening the device in
vdev_disk_open() which is called inside vdev_reopen(). This requires
jumping through some hoops to get to the disk device from the partition
device, and to make sure we can still open the partition after the
BLKRRPART call.
Note that this new code path is triggered on dynamic vdev expansion
only; other actions, like creating a new pool, are unchanged and still
call BLKRRPART from userspace.
This change also depends on API changes which are available in 2.6.37
and latter kernels. The build system has been updated to detect this,
but there is no compatibility mode for older kernels. This means that
online expansion will NOT be available in older kernels. However, it
will still be possible to expand the vdev offline.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#808
This code was was inherited from Solaris which was careful to define
the expected VTOC for various supported architectures. While this
check may have made sense there it's something we should be able to
safely drop under Linux.
However, I'm not quite ready to do that yet. So for the moment I'm
just doing the very safe thing of adding PowerPC as a supported type.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Commit e5dc681a changed EFI_NUMPAR from 9 to 128. This means that the
on-disk EFI label has efi_nparts = 128 instead of 9. The index of the
reserved partition, however, is still 8. This breaks
efi_use_whole_disk(), which uses efi_nparts-1 as the index of the
reserved partition.
This commit fixes efi_use_whole_disk() when the index of the reserved
partition is not efi_nparts-1. It rewrites the algorithm and makes it
more robust by using the order of the partitions instead of their
numbering. It assumes that the last non-empty partition is the reserved
partition, and that the non-empty partition before that is the data
partition.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #808
Currently, zpool_vdev_online() calls zpool_relabel_disk() with a short
partition device name, which is obviously wrong because (1)
zpool_relabel_disk() expects a full, absolute path to use with open()
and (2) efi_write() must be called on an opened disk device, not a
partition device.
With this patch, zpool_relabel_disk() gets called with a full disk
device path. The path is determined using the same algorithm as
zpool_find_vdev().
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #808
The error handling code around zpool_relabel_disk() is either inexistent
or wrong. The function call itself is not checked, and
zpool_relabel_disk() is generating error messages from an unitialized
buffer.
Before:
# zpool online -e homez sdb; echo $?
`: cannot relabel 'sdb1': unable to open device: 2
0
After:
# zpool online -e homez sdb; echo $?
cannot expand sdb: cannot relabel 'sdb1': unable to open device: 2
1
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #808
1949 crash during reguid causes stale config
1953 allow and unallow missing from zpool history since removal of pyzfs
Reviewed by: Adam Leventhal <ahl@delphix.com>
Reviewed by: Matt Ahrens <matt@delphix.com>
Reviewed by: Eric Schrock <eric.schrock@delphix.com>
Reviewed by: Bill Pijewski <wdp@joyent.com>
Reviewed by: Richard Lowe <richlowe@richlowe.net>
Reviewed by: Garrett D'Amore <garrett.damore@gmail.com>
Reviewed by: Dan McDonald <danmcd@nexenta.com>
Reviewed by: Steve Gonczi <gonczi@comcast.net>
Approved by: Eric Schrock <eric.schrock@delphix.com>
References:
https://www.illumos.org/issues/1949https://www.illumos.org/issues/1953
Ported by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#665
Reviewed by: George Wilson <gwilson@zfsmail.com>
Reviewed by: Igor Kozhukhov <ikozhukhov@gmail.com>
Reviewed by: Alexander Eremin <alexander.eremin@nexenta.com>
Reviewed by: Alexander Stetsenko <ams@nexenta.com>
Approved by: Richard Lowe <richlowe@richlowe.net>
References:
https://www.illumos.org/issues/1748
This commit modifies the user to kernel space ioctl ABI. Extra
care should be taken when updating to ensure both the kernel
modules and utilities are updated. If only the user space
component is updated both the 'zpool events' command and the
'zpool reguid' command will not work until the kernel modules
are updated.
Ported by: Martin Matuska <martin@matuska.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#665
FreeBSD #xxx: Dramatically optimize listing snapshots when user
requests only snapshot names and wants to sort them by name, ie.
when executes:
# zfs list -t snapshot -o name -s name
Because only name is needed we don't have to read all snapshot
properties.
Below you can find how long does it take to list 34509 snapshots
from a single disk pool before and after this change with cold and
warm cache:
before:
# time zfs list -t snapshot -o name -s name > /dev/null
cold cache: 525s
warm cache: 218s
after:
# time zfs list -t snapshot -o name -s name > /dev/null
cold cache: 1.7s
warm cache: 1.1s
NOTE: This patch only appears in FreeBSD. If/when Illumos picks up
the change we may want to drop this patch and adopt their version.
However, for now this addresses a real issue.
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #450
When failing to remove a zvol device link because it's busy, wait
a bit and retry in a loop instead of giving up immediately. This
technique is similar to the loop in zpool_label_disk_wait(), with
the same goal: waiting for the asynchronous udev processes to finish
their work.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#692
torvalds/linux@adc0e91ab1 introduced
introduced d_make_root() as a replacement for d_alloc_root(). Further
commits appear to have removed d_alloc_root() from the Linux source
tree. This causes the following failure:
error: implicit declaration of function 'd_alloc_root'
[-Werror=implicit-function-declaration]
To correct this we update the code to use the current d_make_root()
interface for readability. Then we introduce an autotools check
to determine if d_make_root() is available. If it isn't then we
define some compatibility logic which used the older d_alloc_root()
interface.
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#776
When a device is already open O_EXCL by another process the
`zpool import` will correctly fail. However, the default failure
message isn't very helpful. It may in fact be harmful if you
take its advise and destroy your pool.
cannot import 'tank': pool is busy
Destroy and re-create the pool from
a backup source.
Improve the error message in the EBUSY case to simply print a
message indicating that the devices are current in use. The user
will need to manually identify which process has the device open
exclusively and why.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
When creating pools short device names may be used when those
devices appear in certain well known locations under /dev/.
This change adds /dev/mapper/ to that list.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
vdev_id parses the file /etc/zfs/vdev_id.conf to map a physical path
in a storage topology to a channel name. The channel name is combined
with a disk enclosure slot number to create an alias that reflects the
physical location of the drive. This is particularly helpful when it
comes to tasks like replacing failed drives. Slot numbers may also be
re-mapped in case the default numbering is unsatisfactory. The drive
aliases will be created as symbolic links in /dev/disk/by-vdev.
The only currently supported topologies are sas_direct and sas_switch:
o sas_direct - a channel is uniquely identified by a PCI slot and a
HBA port
o sas_switch - a channel is uniquely identified by a SAS switch port
A multipath mode is supported in which dm-mpath devices are handled by
examining the first running component disk, as reported by 'multipath
-l'. In multipath mode the configuration file should contain a
channel definition with the same name for each path to a given
enclosure.
vdev_id can replace the existing zpool_id script on systems where the
storage topology conforms to sas_direct or sas_switch. The script
could be extended to support other topologies as well. The advantage
of vdev_id is that it is driven by a single static input file that can
be shared across multiple nodes having a common storage toplogy.
zpool_id, on the other hand, requires a unique /etc/zfs/zdev.conf per
node and a separate slot-mapping file. However, zpool_id provides the
flexibility of using any device names that show up in
/dev/disk/by-path, so it may still be needed on some systems.
vdev_id's functionality subsumes that of the sas_switch_id script, and
it is unlikely that anyone is using it, so sas_switch_id is removed.
Finally, /dev/disk/by-vdev is added to the list of directories that
'zpool import' will scan.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#713
The mode argument of iops->create()/mkdir()/mknod() was changed from
an 'int' to a 'umode_t'. To prevent a compiler warning an autoconf
check was added to detect the API change and then correctly set a
zpl_umode_t typedef. There is no functional change.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#701
Allow rigorous (and expensive) tx validation to be enabled/disabled
indepentantly from the standard zfs debugging. When enabled these
checks ensure that all txs are constructed properly and that a dbuf
is never dirtied without taking the correct tx hold.
This checking is particularly helpful when adding new dmu consumers
like Lustre. However, for established consumers such as the zpl
with no known outstanding tx construction problems this is just
overhead.
--enable-debug-dmu-tx - Enable/disable validation of each tx as
--disable-debug-dmu-tx it is constructed. By default validation
is disabled due to performance concerns.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Add support for the .zfs control directory. This was accomplished
by leveraging as much of the existing ZFS infrastructure as posible
and updating it for Linux as required. The bulk of the core
functionality is now all there with the following limitations.
*) The .zfs/snapshot directory automount support requires a 2.6.37
or newer kernel. The exception is RHEL6.2 which has backported
the d_automount patches.
*) Creating/destroying/renaming snapshots with mkdir/rmdir/mv
in the .zfs/snapshot directory works as expected. However,
this functionality is only available to root until zfs
delegations are finished.
* mkdir - create a snapshot
* rmdir - destroy a snapshot
* mv - rename a snapshot
The following issues are known defeciences, but we expect them to
be addressed by future commits.
*) Add automount support for kernels older the 2.6.37. This should
be possible using follow_link() which is what Linux did before.
*) Accessing the .zfs/snapshot directory via NFS is not yet possible.
The majority of the ground work for this is complete. However,
finishing this work will require resolving some lingering
integration issues with the Linux NFS kernel server.
*) The .zfs/shares directory exists but no futher smb functionality
has yet been implemented.
Contributions-by: Rohan Puri <rohan.puri15@gmail.com>
Contributiobs-by: Andrew Barnes <barnes333@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#173
Some devices have exhibited sensitivity to the ending alignment of
partitions. In particular, even if the first partition begins at 1
MiB, we have seen many sd driver task abort errors with certain SSDs
if the first partition doesn't end on a 1 MiB boundary. This occurs
when the vdev label is read during pool creation or importation and
causes a delay of about 30 seconds per device. It can also be
simulated with dd when the pool isn't imported:
dd if=/dev/sda1 of=/dev/null bs=262144 count=1
For the record, this problem was observed with SMARTMOD
SG9XCA2E200GE01 200GB SSDs. Unfortunately I don't have a good
explanation for this behavior. It seems to have something to do with
highly fragmented single-sector requests being issued to the device,
which it may not support. With end-aligned partitions at least
page-sized requests were queued and issued to the driver according
to blktrace. In any case, aligning the partition end is a fairly
innocuous work-around, wasting at most 1 MiB of space.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#574
Allow a source rpm to be rebuilt with debugging enabled. This
avoids the need to have to manually modify the spec file. By
default debugging is still largely disabled. To enable specific
debugging features use the following options with rpmbuild.
'--with debug' - Enables ASSERTs
# For example:
$ rpmbuild --rebuild --with debug zfs-modules-0.6.0-rc6.src.rpm
Additionally, ZFS_CONFIG has been added to zfs_config.h for
packages which build against these headers. This is critical
to ensure both zfs and the dependant package are using the same
prototype and structure definitions.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
New SSDs are now available which use an internal 8k block size.
To make sure ZFS can get the maximum performance out of these
devices we're increasing the maximum ashift to 13 (8KB).
This value is still small enough that we can fit 16 uberblocks
in the vdev ring label. However, I don't want to increase this
any futher or it will limit the ability the safely roll back a
pool to recover it.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#565
Resolves nfs-utils-1.0.x compatibility issue which requires
that the fsid be set in the export options.
exportfs: Warning: /tank/dir requires fsid= for NFS export
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#570
DISCARD (REQ_DISCARD, BLKDISCARD) is useful for thin provisioning.
It allows ZVOL clients to discard (unmap, trim) block ranges from
a ZVOL, thus optimizing disk space usage by allowing a ZVOL to
shrink instead of just grow.
We can't use zfs_space() or zfs_freesp() here, since these functions
only work on regular files, not volumes. Fortunately we can use the
low-level function dmu_free_long_range() which does exactly what we
want.
Currently the discard operation is not added to the log. That's not
a big deal since losing discard requests cannot result in data
corruption. It would however result in disk space usage higher than
it should be. Thus adding log support to zvol_discard() is probably
a good idea for a future improvement.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Currently only the (FALLOC_FL_PUNCH_HOLE) flag combination is
supported, since it's the only one that matches the behavior of
zfs_space(). This makes it pretty much useless in its current
form, but it's a start.
To support other flag combinations we would need to modify
zfs_space() to make it more flexible, or emulate the desired
functionality in zpl_fallocate().
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #334
