Linux 5.16 moved XSTATE_XSAVE and XSTATE_XRESTORE out of our reach,
so add our own XSAVE{,OPT,S} code and use it for Linux 5.16.
Please note that this differs from previous behavior in that it
won't handle exceptions created by XSAVE an XRSTOR. This is sensible
for three reasons.
- Exceptions during XSAVE and XRSTOR can only occur if the feature
is not supported or enabled or the memory operand isn't aligned
on a 64 byte boundary. If this happens something else went
terribly wrong, and it may be better to stop execution.
- Previously we just printed a warning and didn't handle the fault,
this is arguable for the above reason.
- All other *SAVE instruction also don't handle exceptions, so this
at least aligns behavior.
Finally add a test to catch such a regression in the future.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Attila Fülöp <attila@fueloep.org>
Closes#13042Closes#13059
Change enforced shell type from `dash` to `sh` and excluded
`SC2039` and `SC3043` by default. `local` keyword is accepted by all
POSIX shells from practical point of view. There is no need anymore
to enforce dash so `local` is accepted.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: szubersk <szuberskidamian@gmail.com>
Closes#13020
`configure` now accepts `--enable-asan` and `--enable-ubsan` switches
which results in passing `-fsanitize=address`
and `-fsanitize=undefined`, respectively, to the compiler. Those
flags are enabled in GitHub workflows for ZTS and zloop. Errors
reported by both instrumentations are corrected, except for:
- Memory leak reporting is (temporarily) suppressed. The cost of
fixing them is relatively high compared to the gains.
- Checksum computing functions in `module/zcommon/zfs_fletcher*`
have UBSan errors suppressed. It is completely impractical
to enforce 64-byte payload alignment there due to performance
impact.
- There's no ASan heap poisoning in `module/zstd/lib/zstd.c`. A custom
memory allocator is used there rendering that measure
unfeasible.
- Memory leaks detection has to be suppressed for `cmd/zvol_id`.
`zvol_id` is run by udev with the help of `ptrace(2)`. Tracing is
incompatible with memory leaks detection.
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: szubersk <szuberskidamian@gmail.com>
Closes#12928
Linux 5.17 sees a rename from complete_and_exit()
to kthread complete_and_exit()
Upstream commit cead18552660702a4a46f58e65188fe5f36e9dfe
("exit: Rename complete_and_exit to kthread_complete_and_exit")
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12989
For us, I think it's always just FALLOC_FL_PUNCH_HOLE with a fake
mustache on.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Coleman Kane <ckane@colemankane.org>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12975
Linux decided to rename this for some reason. At some point, we
should probably invert this mapping, but for now...
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Coleman Kane <ckane@colemankane.org>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12975
add_disk went from void to must-check int return.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Coleman Kane <ckane@colemankane.org>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12975
As it says on the tin - the folio work moved a bunch out of mm.h.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Coleman Kane <ckane@colemankane.org>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12975
Deprecation of Python versions below 3.6 gives opportunity to unify the
build and install requirements for OpenZFS packages. The minimal
supported Python version is 3.6 as this is the most recent Python
package CentOS/RHEL 7 users can get.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Rich Ercolani <rincebrain@gmail.com>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: szubersk <szuberskidamian@gmail.com>
Closes#12925
As an experiment, I stole the lz4 decompressor from
upstream lz4 (1.9.3), and landed it.
Feedback suggested that keeping the vendor lz4 code isolated and
unlinted was probably reasonable, so I lobbed it into its own file.
It also seemed reasonable to put the mostly-untouched* code into
lz4.c proper, and relegate the integrated and ZFS-specific code to
lz4_zfs.c.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12805
Before:
$ time make cstyle
real 0m23.118s
user 0m23.002s
sys 0m0.114s
After:
$ time make cstyle
real 0m4.577s
user 0m31.487s
sys 0m0.699s
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Issue #12899
@LIBFETCH_SONAME@ is no longer quoted. The C define still is.
Ref: 153f7c9f72
Ref: https://github.com/openzfs/zfs/pull/12835#discussion_r776833743
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Damian Szuberski <szuberskidamian@gmail.com>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12922
The definition of struct blkcg_gq was moved into blk-cgroup.h, which is
a header that's been in Linux since 2015. This is used by
vdev_blkg_tryget() in module/os/linux/zfs/vdev_disk.c. Since the kernel
for CentOS 7 and similar-generation releases doesn't have this header,
its inclusion is guarded by a configure test.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#12819
This change adds a confiugre check to determine if bio_set_dev is a
helper macro or not. If not, then the attempt to override its internal
call to bio_associate_blkg(), with a macro definition to our own
version, is no longer possible, as the compiler won't use it when
compiling the new inline function replacement implemented in the header.
This change also creates a new vdev_bio_set_dev() function that performs
the same work, and also performs the work implemented in
vdev_bio_associate_blkg(), as it is the only thing calling that function
in our code. Our custom vdev_bio_associate_blkg() is now only compiled
if the bio_set_dev() is a macro in the Linux headers.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#12819
The iov_iter->type member was renamed iov_iter->iter_type. However,
while looking into this, realized that in 2018 a iov_iter_type(*iov)
accessor function was introduced. So if that is present, use it,
otherwise fall back to trying the existing behavior of directly
accessing type from iov_iter.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#12819
The return type for the submit_bio member of struct
block_device_operations was changed to no longer return a value.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#12819
Due to a possible lock inversion the zvol open call path on Linux
needs to be able to retry in the case where the spa_namespace_lock
cannot be acquired.
For Linux 5.12 an older kernel this was accomplished by returning
-ERESTARTSYS from zvol_open() to request that blkdev_get() drop
the bdev->bd_mutex lock, reaquire it, then call the open callback
again. However, as of the 5.13 kernel this behavior was removed.
Therefore, for 5.12 and older kernels we preserved the existing
retry logic, but for 5.13 and newer kernels we retry internally in
zvol_open(). This should always succeed except in the case where
a pool's vdev are layed on zvols, in which case it may fail. To
handle this case vdev_disk_open() has been updated to retry when
opening a device when -ERESTARTSYS is returned.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #12301Closes#12759
- Remove `SHELLCHECK_IGNORE` in favor of inline suppressions
and more general `SHELLCHECK_OPTS`.
- Exclude `SC2250` (turned on by `--enable=all`) globally
- Pass `--enable=all` to shellcheck for scripts in contrib/: it's
very important to catch errors early in areas that are not easily
testable.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: szubersk <szuberskidamian@gmail.com>
Closes#12760
Linux 5.16 moved these functions into this new header in commit
1b4fb8545f2b00f2844c4b7619d64d98440a477c. This change adds code to look
for the presence of this header, and include it so that the code using
xgetbv & xsetbv will compile again.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#12800
Instead, linux/pagemap.h offers a number of folio-specific functions to
be called instead. In this case, module/os/linux/zfs/zfs_vnops_os.c
wants to call wait_on_page_bit(pp, PG_writeback). This gets replaced
with folio_wait_bit(folio_page(pp), PG_writeback). This change modifies
the code to conditionally compile that if configure identifies th
presence of the folio_wait_bit() function.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#12800
The submit_bio() prototype has changed again. The version is 5.16
still only expects a single argument but the return type has changed
to void. Since we never used the returned value before update the
configure check to detect both single arg versions.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12725
There was a fallback case I overlooked in the initial patch, with
a similarly imperfect version extractor.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12045Closes#12673
Gentoo and Alpine always set the rc init scripts' shebang to
#!/sbin/openrc-run, whether or not openrc is installed.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Peter Levine <plevine457@gmail.com>
Closes#12683Closes#12692
As of the Linux 5.9 kernel a fallthrough macro has been added which
should be used to anotate all intentional fallthrough paths. Once
all of the kernel code paths have been updated to use fallthrough
the -Wimplicit-fallthrough option will because the default. To
avoid warnings in the OpenZFS code base when this happens apply
the fallthrough macro.
Additional reading: https://lwn.net/Articles/794944/
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12441
Kernel commits
332f606b32b6 ovl: enable RCU'd ->get_acl()
0cad6246621b vfs: add rcu argument to ->get_acl() callback
Added compatibility code to detect the new ->get_acl() interface
and correctly handle the case where the new rcu argument is set.
Reviewed-by: Coleman Kane <ckane@colemankane.org>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12548
Kernel commits
39f75da7bcc8 ("isystem: trim/fixup stdarg.h and other headers")
c0891ac15f04 ("isystem: ship and use stdarg.h")
564f963eabd1 ("isystem: delete global -isystem compile option")
(for now can be found in linux-next.git tree, will land into the
Linus' tree during the ongoing 5.15 cycle with one of akpm merges)
removed the -isystem flag and disallowed the inclusion of any
compiler header files. They also introduced a minimal
<linux/stdarg.h> as a replacement for <stdarg.h>.
include/os/linux/spl/sys/cmn_err.h in the ZFS source tree includes
<stdarg.h> unconditionally. Introduce a test for <linux/stdarg.h>
and include it instead of the compiler's one to prevent module
build breakage.
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Closes#12531
The 5.15 kernel moved the backing_dev_info structure out of
the request queue structure which causes a build failure.
Rather than look in the new location for the BDI we instead
detect this upstream refactoring by the existance of either
the blk_queue_update_readahead() or disk_update_readahead()
functions. In either case, there's no longer any reason to
manually set the ra_pages value since it will be overridden
with a reasonable default (2x the block size) when
blk_queue_io_opt() is called.
Therefore, we update the compatibility wrapper to do nothing
for 5.9 and newer kernels. While it's tempting to do the
same for older kernels we want to keep the compatibility
code to preserve the existing behavior. Removing it would
effectively increase the default readahead to 128k.
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12532
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Melikov <mail@gmelikov.ru>
Closes#12529
To avoid clashing with tags and releases, we'll use "zfs-macOS".
Meta: 1
Name: zfs-macOS
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Closes#12437
We're not looking for bdev_disk_changed.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#12492
Kernel 5.14 introduced a change where set_page_dirty of
struct address_space_operations is no longer implicitly set to
__set_page_dirty_buffers(), which ended up resulting in a NULL
pointer deref in the kernel when it is attempted to be called.
This change sets .set_page_dirty in the structure to
__set_page_dirty_nobuffers(), which was introduced with the
related patch set. The breaking change was introduce in commit
0af573780b0b13fceb7fabd49dc1b073cee9a507 to torvalds/linux.git.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#12427
In Linux 5.14, blk_alloc_queue is no longer exported, and its usage
has been superseded by blk_alloc_disk, which returns a gendisk struct
from which we can still retrieve the struct request_queue* that is
needed in the one place where it is used. This also replaces the call
to alloc_disk(minors), and minors is now set via struct member
assignment.
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Reviewed-by: Coleman Kane <ckane@colemankane.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12362Closes#12409
Move HAVE_LARGE_STACKS definitions to header and set when appropriate.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Kevin Bowling <kbowling@FreeBSD.org>
Closes#12350
In absence of LTO, and dynamic libatomic, la.so ends up in the needs
section of every toolchain executable; some consider this an issue.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12345Closes#12359
There are at least two interpretations of basename(3),
in addition to both functions being allowed to /both/ return a static
buffer (unsuitable in multi-threaded environments) /and/ raze the input
(which encourages overallocations, at best)
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12105
It turns out the ax_python_devel.m4 version check assumes that
("3.X+1.0" >= "3.X.0") is True in Python, which is not when X+1
is 10 or above and X is not. (Also presumably X+1=100 and ...)
So let's remake the check to behave consistently, using the
"packaging" or (if absent) the "distlib" modules.
(Also, update the Github workflows to use the new packages.)
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes: #12073
There's already logic to force INVARIANTS on for building if it's
present in the running kernel; however, not having DEBUG enabled
when DEBUG and INVARIANTS are can cause strange panics.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12185Closes#12163
Also mark all printf-like funxions in libzfs_impl.h as printf-like
and add --no-show-locs to storeabi, in hopes diffs will make more sense
in future
This removes these symbols from libzfs:
D nfs_only
T SHA256Init
T SHA2Final
T SHA2Init
T SHA2Update
T SHA384Init
T SHA512Init
D share_all_proto
D smb_only
T zfs_is_shared_proto
W zpool_mount_datasets
W zpool_unmount_datasets
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12048
make_gitrev.sh actually breaks checkbashisms' parser,
which /insists/ that the end-of-line " is actually a string start
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12101
This checks every file it checked (and a few more),
but explicitly instead of "if it works it works" best-effort
(which wasn't that good anyway)
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#10512Closes#12101
configure on s390x has a key check fail with an error about
a variable being used uninitialized. So let's initialize it.
Reviewed-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12126
wmsum counters are a reduced version of aggsum counters, optimized for
write-mostly scenarios. They do not provide optimized read functions,
but instead allow much cheaper add function. The primary usage is
infrequently read statistic counters, not requiring exact precision.
The Linux implementation is directly mapped into percpu_counter KPI.
The FreeBSD implementation is directly mapped into counter(9) KPI.
In user-space due to lack of better implementation mapped to aggsum.
Unfortunately neither Linux percpu_counter nor FreeBSD counter(9)
provide sufficient functionality to completelly replace aggsum, so
it still remains to be used for several hot counters.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12114
Just like #12087, the set_acl signature changed with all the bolted-on
*userns parameters, which disabled set_acl usage, and caused #12076.
Turn zpl_set_acl into zpl_set_acl and zpl_set_acl_impl, and add a
new configure test for the new version.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12076Closes#12093
Linux changed the tmpfile() signature again in torvalds/linux@6521f89,
which in turn broke our HAVE_TMPFILE detection in configure.
Update that macro to include the new case, and change the signature of
zpl_tmpfile as appropriate.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes: #12060Closes: #12087
Add support for http and https to the keylocation properly to
allow encryption keys to be fetched from the specified URL.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Issue #9543Closes#9947Closes#11956
Linux kernel commit 0f00b82e5413571ed225ddbccad6882d7ea60bc7 removes the
revalidate_disk() handler from struct block_device_operations. This
caused a regression, and this commit eliminates the call to it and the
assignment in the block_device_operations static handler assignment
code, when configure identifies that the kernel doesn't support that
API handler.
Reviewed-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#11967Closes#11977
This replaces the generic libspl atomic.c atomics implementation
with one based on builtin gcc atomics. This functionality was added
as an experimental feature in gcc 4.4. Today even CentOS 7 ships
with gcc 4.8 as the default compiler we can make this the default.
Furthermore, the builtin atomics are as good or better than our
hand-rolled implementation so it's reasonable to drop that custom code.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11904
This change adds SIGSTOP and SIGTSTP handling to the issig function;
this mirrors its behavior on Solaris. This way, long running kernel
tasks can be stopped with the appropriate signals. Note that doing
so with ctrl-z on the command line doesn't return control of the tty
to the shell, because tty handling is done separately from stopping
the process. That can be future work, if people feel that it is a
necessary addition.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Issue #810
Issue #10843Closes#11801
Added a check for alien 8.95.{1,2,3}, which is known to fail to
generate debs 100% of the time, and instead print out a message
informing the developer that it's known to be broken and linking
them to more information.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#11848Closes#11850
Correct an assortment of typos throughout the code base.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Closes#11774
Bump the library versions as advised by the libtool guidelines.
https://www.gnu.org/software/libtool/manual/html_node/Updating-version-info.html
Two new functions were added but no existing functions were changed,
so we increase the version and the age (version:revision:age).
Added functions (2):
- boolean_t zpool_is_draid_spare(const char *);
- zpool_compat_status_t zpool_load_compat(const char *,
boolean_t *, char *, char *);
Additionally bump the libzpool.so version information. This library
is for internal use but we still want to update the version to track
major changes to the interfaces.
The libzfsbootenv, libuutil, libnvpair and libzfs_core libraries
have not been updated.
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11817
The configure check for iops->rename wanting flags was missing the
AC_MSG_CHECKING() so it would just print yes without saying what was
being checked.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Brian Atkinson <batkinson@lanl.gov>
Closes#11825
The BIO_MAX_PAGES macro is being retired in favor of a bio_max_segs()
function that implements the typical MIN(x,y) logic used throughout the
kernel for bounding the allocation, and also the new implementation is
intended to be signed-safe (which the former was not).
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#11765
In Linux 5.12, the filesystem API was modified to support ipmapped
mounts by adding a "struct user_namespace *" parameter to a number
functions and VFS handlers. This change adds the needed autoconf
macros to detect the new interfaces and updates the code appropriately.
This change does not add support for idmapped mounts, instead it
preserves the existing behavior by passing the initial user namespace
where needed. A subsequent commit will be required to add support
for idmapped mounted.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#11712
Wire up the --enable-debug flag for configure to the FreeBSD module
build. Add --enable-invariants.
The running FreeBSD kernel config is used to detect whether to enable
INVARIANTS if not explicitly specified with --enable-invariants or
--disable-invariants.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11678
The bio_*_acct functions became GPL exports, which causes the
kernel modules to refuse to compile. This replaces code with
alternate function calls to the disk_*_io_acct interfaces, which
are not GPL exports. This change was added in kernel commit
99dfc43ecbf67f12a06512918aaba61d55863efc.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#11639
The struct bio member bi_disk was moved underneath a new member named
bi_bdev. So all attempts to reference bio->bi_disk need to now become
bio->bi_bdev->bd_disk.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#11639
Property to allow sets of features to be specified; for compatibility
with specific versions / releases / external systems. Influences
the behavior of 'zpool upgrade' and 'zpool create'. Initial man
page changes and test cases included.
Brief synopsis:
zpool create -o compatibility=off|legacy|file[,file...] pool vdev...
compatibility = off : disable compatibility mode (enable all features)
compatibility = legacy : request that no features be enabled
compatibility = file[,file...] : read features from specified files.
Only features present in *all* files will be enabled on the
resulting pool. Filenames may be absolute, or relative to
/etc/zfs/compatibility.d or /usr/share/zfs/compatibility.d (/etc
checked first).
Only affects zpool create, zpool upgrade and zpool status.
ABI changes in libzfs:
* New function "zpool_load_compat" to load and parse compat sets.
* Add "zpool_compat_status_t" typedef for compatibility parse status.
* Add ZPOOL_PROP_COMPATIBILITY to the pool properties enum
* Add ZPOOL_STATUS_COMPATIBILITY_ERR to the pool status enum
An initial set of base compatibility sets are included in
cmd/zpool/compatibility.d, and the Makefile for cmd/zpool is
modified to install these in $pkgdatadir/compatibility.d and to
create symbolic links to a reasonable set of aliases.
Reviewed-by: ericloewe
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Colm Buckley <colm@tuatha.org>
Closes#11468
This compatibility code is no longer needed. For it a while
iov_iter_init_compat() was used by zfs_uio_prefaultpages() but
this code should have been dropped as part of commit 83b91ae1.
Take care of that oversight and remove it.
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11543
In order for cppcheck to perform a proper analysis it needs to be
aware of how the sources are compiled (source files, include
paths/files, extra defines, etc). All the needed information is
available from the Makefiles and can be leveraged with a generic
cppcheck Makefile target. So let's add one.
Additional minor changes:
* Removing the cppcheck-suppressions.txt file. With cppcheck 2.3
and these changes it appears to no longer be needed. Some inline
suppressions were also removed since they appear not to be
needed. We can add them back if it turns out they're needed
for older versions of cppcheck.
* Added the ax_count_cpus m4 macro to detect at configure time how
many processors are available in order to run multiple cppcheck
jobs. This value is also now used as a replacement for nproc
when executing the kernel interface checks.
* "PHONY =" line moved in to the Rules.am file which is included
at the top of all Makefile.am's. This is just convenient becase
it allows us to use the += syntax to add phony targets.
* One upside of this integration worth mentioning is it now allows
`make cppcheck` to be run in any directory to check that subtree.
* For the moment, cppcheck is not run against the FreeBSD specific
kernel sources. The cppcheck-FreeBSD target will need to be
implemented and testing on FreeBSD to support this.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11508
Several m4 macros have been retired in autoconf 2.70. Update the
the build system to use the new macros provided to replace them.
* Replaced AC_HELP_STRING with AS_HELP_STRING.
* Replaced AC_TRY_COMPILE with AC_COMPILE_IFELSE/AC_LANG_PROGRAM.
* Replaced AC_CANONICAL_SYSTEM with AC_CANONICAL_TARGET
* Replaced AC_PROG_LIBTOOL with LT_INIT
* $CPP is not defined in ZFS_AC_KERNEL and really shouldn't be
directly used like this. Replace it with an $AWK command
to extract the kernel source version.
Reviewed-by: Eli Schwartz <eschwartz@archlinux.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #11413Closes#11419
As of 5.11 the blk_register_region() and blk_unregister_region()
functions have been retired. This isn't a problem since add_disk()
has implicitly allocated minor numbers for a very long time.
Reviewed-by: Rafael Kitover <rkitover@gmail.com>
Reviewed-by: Coleman Kane <ckane@colemankane.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11387Closes#11390
Both revalidate_disk_size() and revalidate_disk() have been removed.
Functionally this isn't a problem because we only relied on these
functions to call zvol_revalidate_disk() for us and to perform any
additional handling which might be needed for that kernel version.
When neither are available we know there's no additional handling
needed and we can directly call zvol_revalidate_disk().
Reviewed-by: Rafael Kitover <rkitover@gmail.com>
Reviewed-by: Coleman Kane <ckane@colemankane.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11387Closes#11390
The bd_contains member was removed from the block_device structure.
Callers needing to determine if a vdev is a whole block device should
use the new bdev_whole() wrapper. For older kernels we provide our
own bdev_whole() wrapper which relies on bd_contains for compatibility.
Reviewed-by: Rafael Kitover <rkitover@gmail.com>
Reviewed-by: Coleman Kane <ckane@colemankane.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11387Closes#11390
The generic IO accounting functions have been removed in favor of the
bio_start_io_acct() and bio_end_io_acct() functions which provide a
better interface. These new functions were introduced in the 5.8
kernels but it wasn't until the 5.11 kernel that the previous generic
IO accounting interfaces were removed.
This commit updates the blk_generic_*_io_acct() wrappers to provide
and interface similar to the updated kernel interface. It's slightly
different because for older kernels we need to pass the request queue
as well as the bio.
Reviewed-by: Rafael Kitover <rkitover@gmail.com>
Reviewed-by: Coleman Kane <ckane@colemankane.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11387Closes#11390
The lookup_bdev() function has been updated to require a dev_t
be passed as the second argument. This is actually pretty nice
since the major number stored in the dev_t was the only part we
were interested in. This allows to us avoid handling the bdev
entirely. The vdev_lookup_bdev() wrapper was updated to emulate
the behavior of the new lookup_bdev() for all supported kernels.
Reviewed-by: Rafael Kitover <rkitover@gmail.com>
Reviewed-by: Coleman Kane <ckane@colemankane.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11387Closes#11390
Update the ZFS_LINUX_TEST_PROGRAM macro to always set the module
license. As of the 5.11 kernel not setting a license has been
converted from a warning to an error.
Reviewed-by: Rafael Kitover <rkitover@gmail.com>
Reviewed-by: Coleman Kane <ckane@colemankane.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11387Closes#11390
The CentOS stream 4.18.0-257 kernel appears to have backported
the Linux 5.9 change to make_request_fn and the associated API.
To maintain weak modules compatibility the original symbol was
retained and the new interface blk_alloc_queue_rh() was added.
Unfortunately, blk_alloc_queue() was replaced in the blkdev.h
header by blk_alloc_queue_bh() so there doesn't seem to be a way
to build new kmods against the old interfces. Even though they
appear to still be available for weak module binding.
To accommodate this a configure check is added for the new _rh()
variant of the function and used if available. If compatibility
code gets added to the kernel for the original blk_alloc_queue()
interface this should be fine. OpenZFS will simply continue to
prefer the new interface and only fallback to blk_alloc_queue()
when blk_alloc_queue_rh() isn't available.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11374
As of the 5.10 kernel the generic splice compatibility code has been
removed. All filesystems are now responsible for registering a
->splice_read and ->splice_write callback to support this operation.
The good news is the VFS provided generic_file_splice_read() and
iter_file_splice_write() callbacks can be used provided the ->iter_read
and ->iter_write callback support pipes. However, this is currently
not the case and only iovecs and bvecs (not pipes) are ever attached
to the uio structure.
This commit changes that by allowing full iov_iter structures to be
attached to uios. Ever since the 4.9 kernel the iov_iter structure
has supported iovecs, kvecs, bvevs, and pipes so it's desirable to
pass the entire thing when possible. In conjunction with this the
uio helper functions (i.e uiomove(), uiocopy(), etc) have been
updated to understand the new UIO_ITER type.
Note that using the kernel provided uio_iter interfaces allowed the
existing Linux specific uio handling code to be simplified. When
there's no longer a need to support kernel's older than 4.9, then
it will be possible to remove the iovec and bvec members from the
uio structure and always use a uio_iter. Until then we need to
maintain all of the existing types for older kernels.
Some additional refactoring and cleanup was included in this change:
- Added checks to configure to detect available iov_iter interfaces.
Some are available all the way back to the 3.10 kernel and are used
when available. In particular, uio_prefaultpages() now always uses
iov_iter_fault_in_readable() which is available for all supported
kernels.
- The unused UIO_USERISPACE type has been removed. It is no longer
needed now that the uio_seg enum is platform specific.
- Moved zfs_uio.c from the zcommon.ko module to the Linux specific
platform code for the zfs.ko module. This gets it out of libzfs
where it was never needed and keeps this Linux specific code out
of the common sources.
- Removed unnecessary O_APPEND handling from zfs_iter_write(), this
is redundant and O_APPEND is already handled in zfs_write();
Reviewed-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11351
ZFS currently doesn't react to hotplugging cpu or memory into the
system in any way. This patch changes that by adding logic to the ARC
that allows the system to take advantage of new memory that is added
for caching purposes. It also adds logic to the taskq infrastructure
to support dynamically expanding the number of threads allocated to a
taskq.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Matthew Ahrens <matthew.ahrens@delphix.com>
Co-authored-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#11212
Busybox's mktemp requires at least six X's in the template, causing
the current sed --in-place check to fail because the file does not
exist. This change adds additional X's to mktemp templates that do
not already have at least six X's in them.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Quentin Zdanis <zdanisq@gmail.com>
Closes#11269
RPM and DEB packages are named after the SONAME version of the library
they contain. After bumping this version, the packaging should be
renamed.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Antonio Russo <aerusso@aerusso.net>
Closes#11219
Provide two make targets: checkabi and storeabi.
storeabi uses libabigail to generate a reference copy of the ABI for the
public libraries.
checkabi compares such a reference to the compiled version, failing if
they are not compatible. No ABI is generated for libzpool.so, it is
only used by ztest and zdb and not external consumers.
Co-authored-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Antonio Russo <aerusso@aerusso.net>
Closes#11144
A new function was added named revalidate_disk_size() and the old
revalidate_disk() appears to have been deprecated. As the only ZFS
code that calls this function is zvol_update_volsize, swapping the
old function call out for the new one should be all that is required.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#11085
Kernel 5.10 removed check_disk_change() in favor of callers using
the faster bdev_check_media_change() instead, and explicitly forcing
bdev revalidation when they desire that behavior. To preserve prior
behavior, I have wrapped this into a zfs_check_media_change() macro
that calls an inline function for the new API that mimics the old
behavior when check_disk_change() doesn't exist, and just calls
check_disk_change() if it exists.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#11085
Kernel commit 2b0d3d3e4fcfb brought in some changes to the struct
percpu_ref structure that moves most of its fields into a member
struct named "data" of type struct percpu_ref_data. This includes
the "count" member which is updated by vdev_blkg_tryget(), so update
this function to chase the API change, and detect it via configure.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#11085
In Linux 5.10 the linux/frame.h header was renamed linux/objtool.h.
Add a configure check to detect and use the correctly named header.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11085
Missing struct initialization in a config test results in the
interface being incorrectly detected.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Adam Moss <c@yotes.com>
Signed-off-by: Mathieu Velten <matmaul@gmail.com>
Closes#10713Closes#11049
This check was accidentally broken when the kABI checks were updated
to run in parallel, commit 608f874. The check must be for the
config_debug_lock_alloc_license name to determine if the symbol
is license compatible.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#10991
The m4 objtool configure check can incorrectly fail because of a
missing header in the test. This appears to be the result of a
recent kernel change and was observed on the Fedora 5.8.11-200
kernel.
In file included from /home/fedora/zfs/build/objtool/objtool.c:75:
./arch/x86/include/asm/frame.h💯57: error: 'struct pt_regs'
declared inside parameter list will not be visible outside
of this definition or declaration [-Werror]
The consequence of this is that the "stack_frame_non_standard"
check is never run and HAVE_STACK_FRAME_NON_STANDARD is set
incorrectly which results in a build failure. This change adds
the appropriate header to the "objtool" check so it now behaves
as intended.
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#10990
The zfs-initramfs package has never worked as no RPM-based distribution
uses initramfs-tools, which is listed as a dependency of zfs-initramfs.
This would not ordinarily be a problem, as it is only enabled when
/usr/share/initramfs-tools is present, which should not normally be the
case on RPM-based distributions. However, other packages may install
unused files there even if initramfs-tools is not used, so remove this
auto-detection for the rpm-utils target.
This does not fully remove the logic for the zfs-initramfs package. This
splits it out into a separate rpm-utils-initramfs target so that the
Debian builds can still use it.
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Harald van Dijk <harald@gigawatt.nl>
Closes#10898
Several of the listed library dependencies are not relevant on FreeBSD.
Have ./configure save libraries that are found via pkg-config as
${LIB}_PC and use the configured automake variables instead of hard
coded names so we only get what was actually needed.
While here, update the URL to point at the OpenZFS Github repo.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10869
Commit dcdc12e added compatibility code to treat NR_SLAB_RECLAIMABLE_B
as if it were the same as NR_SLAB_RECLAIMABLE. However, the new value
is in bytes while the old value was in pages which means they are not
interchangeable.
The only place the reclaimable slab size is used is as a component of
the calculation done by arc_free_memory(). This function returns the
amount of memory the ARC considers to be free or reclaimable at little
cost. Rather than switch to a new interface to get this value it has
been removed it from the calculation. It is normally a minor component
compared to the number of inactive or free pages, and removing it
aligns the behavior with the FreeBSD version of arc_free_memory().
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Coleman Kane <ckane@colemankane.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#10834
This will allow an override of auto-detection of distribution, which
is based on checking presence of /etc/*-release files.
Build systems makes a lot of file location assumptions based on
detected distribution.
Some distributions (like gentoo) may prefer explicitly
setting --with-vendor=gentoo to avoid auto-detection.
Since auto-detection checks all files in order, current script may
misdetect even on gentoo system if /etc/redhat-release file is present
Default behavior is unchanged and default is --with-vendor=check
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Georgy Yakovlev <gyakovlev@gentoo.org>
Closes#10835
ZStandard is a modern, high performance, general compression algorithm.
It provides similar or better compression levels to GZIP, but with much
better performance. ZStandard provides a large selection of compression
levels to allow a storage administrator to select the preferred
performance/compression trade-off.
This commit imports the unmodified ZStandard single-file library which
will be used by ZFS.
The implementation of this new library is done with future updates of
zstd in mind. For this reason we integrated the code in a way, that does
not require modifications to the library. For more details, see
`module/zstd/README.md`.
The library is excluded from codecov calculation and cppcheck as
unaltered dependencies do not need full codecov or cppcheck.
Co-authored-by: Allan Jude <allanjude@freebsd.org>
Co-authored-by: Kjeld Schouten-Lebbing <kjeld@schouten-lebbing.nl>
Co-authored-by: Michael Niewöhner <foss@mniewoehner.de>
Signed-off-by: Allan Jude <allanjude@freebsd.org>
Signed-off-by: Kjeld Schouten-Lebbing <kjeld@schouten-lebbing.nl>
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
The make_request_fn and associated API was replaced recently in a
Linux 5.9 merge, to replace its functionality with a new submit_bio
member in struct block_device_operations.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#10696
This change appears to primarily be a name change for the enum. Had
to update the test logic so that it works so long as either one of
these is present (favoring the newer one). Additionally, as this is
newer, it only shows up in node_page_item, so this commit doesn't
test zone_page_item for the same enum.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#10696
Many of the block device operations (often functions with bdev in
the name) were moved into linux/blkdev.h from linux/fs.h. Seems
that this header is already included where needed in the code, but
in the autoconf tests it was missing causing false negatives. This
commit has those tests include linux/fs.h (old location) and now
also linux/blkdev.h (new locations).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#10696
FreeBSD defines _BIG_ENDIAN BIG_ENDIAN _LITTLE_ENDIAN
LITTLE_ENDIAN on every architecture. Trying to do
cross builds whilst hiding this from ZFS has proven
extremely cumbersome.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10621
Stock kernels older than 4.10 do not export the has_capability()
function which is required by commit e59a377. To avoid breaking
the build on older kernels revert to the safe legacy behavior and
return EACCES when privileges cannot be checked.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Matt Ahrens <matt@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#10565Closes#10573
A bunch of places need to edit files to incorporate the configured paths
i.e. bindir, sbindir etc. Move this logic into a common file.
Create arc_summary by copying arc_summary[23] as appropriate at build
time instead of install time.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Closes#10559
The configure variables won't be defined if CONFIG_KERNEL is disabled
and defining empty macros causes errors. The spec files do provide some
defaults if the macros are undefined.
Remove config conditionals in the tgz Makefile.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Closes#10564
When building srpm using make -j, each of the recursive makes invoked to
build srpm-{dkms,kmod,utils} will build the dist target. This is both
unnecessary, and also has a very good chance of breaking when they race
trying to build gitrev.
Fix this by make dist a prerequisite of srpm-{dkms,kmod,utils} instead
of srpm-common, so that it will be done once before invoking the
recursive makes.
Also, gitrev is not really required for make dist, so instead of adding
it to BUILT_SOURCES, just add it as a prerequisite of the all target.
Mark the individual package targets as PHONY.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Closes#10564
Make FIND_SYSTEM_LIBRARY respect a configured sysroot, otherwise it
might find headers from the build machine and assume the library is
available on the host/target.
Tighten up error checking: if pkg-config or the user specified _CFLAGS
or _LIBS but we can't find the header/library, issue a fatal error.
Fix the -L flag to /usr/local/lib instead of just /usr/local.
Clean out the _CFLAGS and _LIBS if we located something that we later
find doesn't work.
Rename FIND_SYSTEM_LIBRARY into the ZFS_AC_ scope.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Closes#10538
Commit e8864b1b28 ("config: libintl/libiconv for gettext() detection")
added an empty config.rpath with a comment that the real one doesn't
work with libtool.
However, an empty config.rpath doesn't really work: eg. on FreeBSD,
where libintl is in /usr/local/lib, configure thinks that gettext
doesn't exist and NLS should be disabled, which currently isn't
supported in the source, and hence requires manual workaround to
directly link -lintl without relying on configure. config.rpath is
essential to let it be detected either in --prefix or using
--with-libintl-prefix.
I also don't see the mentioned issue with libtool flags applied to
compilation, it seems to work fine to pass LTLIBINTL to libtool. It's
unnecessary to include LTLIBICONV as the configure test will
automatically append that to LTLIBINTL if it is necessary to link with
libiconv.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Closes#10538
libzutil is currently statically linked into libzfs, libzfs_core and
libzpool. Avoid the unnecessary duplication by removing it from libzfs
and libzpool, and adding libzfs_core to libzpool.
Remove a few unnecessary dependencies:
- libuutil from libzfs_core
- libtirpc from libspl
- keep only libcrypto in libzfs, as we don't use any functions from
libssl
- librt is only used for clock_gettime, however on modern systems that's
in libc rather than librt. Add a configure check to see if we actually
need librt
- libdl from raidz_test
Add a few missing dependencies:
- zlib to libefi and libzfs
- libuuid to zpool, and libuuid and libudev to zed
- libnvpair uses assertions, so add assert.c to provide aok and
libspl_assertf
Sort the LDADD for programs so that libraries that satisfy dependencies
come at the end rather than the beginning of the linker command line.
Revamp the configure tests for libaries to use FIND_SYSTEM_LIBRARY
instead. This can take advantage of pkg-config, and it also avoids
polluting LIBS.
List all the required dependencies in the pkgconfig files, and move the
one for libzfs_core into the latter's directory. Install pkgconfig files
in $(libdir)/pkgconfig on linux and $(prefix)/libdata/pkgconfig on
FreeBSD, instead of /usr/share/pkgconfig, as the more correct location
for library .pc files.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Closes#10538
a+=b is not supported by all shells. It is equivalent to a=${a}b, so
just rewrite it as that.
This also fixes commit 9ea6c3d3, which intended to only make the
definitions of _dracutdir, _udevdir, and _udevruledir conditional, but
actually ensured that _initconfdir no longer got defined if _dracutdir
was defined, and defined _udevdir to the value that should have been
used for _udevruledir.
This also fixes the fact that the checks introduced by commit 9ea6c3d3
could never work: ZFS_AC_PACKAGE was called before the configuration
options were processed.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Harald van Dijk <harald@gigawatt.nl>
Closes#10518
The standard test command does not support the == operator. Certain
shells, including bash, do support it, but in those shells it does
exactly the same thing as the standard = operator. Use that instead.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Harald van Dijk <harald@gigawatt.nl>
Closes#10509
This doesn't appear to be used by the buildbot any more, let's remove
it.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Closes#10506
A previous commit enabled the tracking of object allocations
in Linux-backed caches from the SPL layer for debuggability.
The commit is: 9a170fc6fe54f1e852b6c39630fe5ef2bbd97c16
Unfortunately, it also introduced minor performance regressions
that were highlighted by the ZFS perf test-suite. Within Delphix
we found that the regression would be from -1%, all the way up
to -8% for some workloads.
This commit brings performance back up to par by creating a
separate counter for those caches and making it a percpu in
order to avoid lock-contention.
The initial performance testing was done by myself, and the
final round was conducted by @tonynguien who was also the one
that discovered the regression and highlighted the culprit.
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Closes#10397
Reduce the usage of EXTRA_DIST. If files are conditionally included in
_SOURCES, _HEADERS etc, automake is smart enough to dist all files that
could possibly be included, but this does not apply to EXTRA_DIST,
resulting in make dist depending on the configuration.
Add some files that were missing altogether in various Makefile's.
The changes to disted files in this commit (excluding deleted files):
+./cmd/zed/agents/README.md
+./etc/init.d/README.md
+./lib/libspl/os/freebsd/getexecname.c
+./lib/libspl/os/freebsd/gethostid.c
+./lib/libspl/os/freebsd/getmntany.c
+./lib/libspl/os/freebsd/mnttab.c
-./lib/libzfs/libzfs_core.pc
-./lib/libzfs/libzfs.pc
+./lib/libzfs/os/freebsd/libzfs_compat.c
+./lib/libzfs/os/freebsd/libzfs_fsshare.c
+./lib/libzfs/os/freebsd/libzfs_ioctl_compat.c
+./lib/libzfs/os/freebsd/libzfs_zmount.c
+./lib/libzutil/os/freebsd/zutil_compat.c
+./lib/libzutil/os/freebsd/zutil_device_path_os.c
+./lib/libzutil/os/freebsd/zutil_import_os.c
+./module/lua/README.zfs
+./module/os/linux/spl/README.md
+./tests/README.md
+./tests/zfs-tests/tests/functional/cli_root/zfs_clone/zfs_clone_rm_nested.ksh
+./tests/zfs-tests/tests/functional/cli_root/zfs_send/zfs_send_encrypted_unloaded.ksh
+./tests/zfs-tests/tests/functional/inheritance/README.config
+./tests/zfs-tests/tests/functional/inheritance/README.state
+./tests/zfs-tests/tests/functional/rsend/rsend_016_neg.ksh
+./tests/zfs-tests/tests/perf/fio/sequential_readwrite.fio
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Closes#10501
Implements a pam module for automatically loading zfs encryption keys
for home datasets. The pam module:
- loads a zfs key and mounts the dataset when a session opens.
- unmounts the dataset and unloads the key when the session closes.
- when the user is logged on and changes the password, the module
changes the encryption key.
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: @jengelh <jengelh@inai.de>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Felix Dörre <felix@dogcraft.de>
Closes#9886Closes#9903
The test added in commit
4313a5b4c5 ("Detect if sed supports --in-place")
doesn't work at least on my system (autoconfig-2.69).
The issue is that SED has already been found and cached before this
function is evaluated, with the result that the test is completely
skipped.
...
checking for a sed that does not truncate output... /usr/bin/sed
...
checking for sed --in-place... (cached) /usr/bin/sed
The first test is executed by libtool.m4. This looks to have been around
in libtool for at least 15 years or so, not sure why this was not
encountered at the time of the original commit.
Fix this by caching the value of the ac_inplace flag rather than the
path to SED. Also use $SED and add AC_REQUIRE to ensure that we use the
sed that was located by the standard configure test.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Closes#10493
Currently an out-of-tree build does not work with read-only source
directory because zfs_gitrev.h can't be created. Move this file to the
build directory, which is more appropriate for a generated file, and
drop the dist-hook for zfs_gitrev.h. There is no need to distribute this
file since it will be regenerated as part of the compilation in any
case.
scripts/make_gitrev.sh tries to avoid updating zfs_gitrev.h if there has
been no change, however this doesn't cover the case when the source
directory is not in git: in that case zfs_gitrev.h gets overwritten even
though it's always "unknown". Simplify the logic to always write out a
new version of zfs_gitrev.h, compare against the old and overwrite only
if different. This is now simple enough to just include in the
Makefile, so drop the script.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Closes#10493
Rephrase comments to be more clear.
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#10481
Switch on warning flags to detect mismatch between declaration and
definition.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Closes#10470
Correct various typos in the comments and tests.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Closes#10423
The `pgprot` argument has been removed from `__vmalloc` in Linux 5.8,
being `PAGE_KERNEL` always now [1].
Detect this during configure and define a wrapper for older kernels.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/commit/mm/vmalloc.c?h=next-20200605&id=88dca4ca5a93d2c09e5bbc6a62fbfc3af83c4fca
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Co-authored-by: Michael Niewöhner <foss@mniewoehner.de>
Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Closes#10422
Usage of this variable uninitialized triggers -Werror,-Wuninitialized
when compiled under clang for linux kernel 5.6, leading the build system
to believe that the function is not declared.
This commit initializes the variable to suppress the warning and fix the
build for kernel 5.6 with clang.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Hiếu Lê <leorize+oss@disroot.org>
Closes#10279Closes#10281
Add the FreeBSD platform code to the OpenZFS repository. As of this
commit the source can be compiled and tested on FreeBSD 11 and 12.
Subsequent commits are now required to compile on FreeBSD and Linux.
Additionally, they must pass the ZFS Test Suite on FreeBSD which is
being run by the CI. As of this commit 1230 tests pass on FreeBSD
and there are no unexpected failures.
Reviewed-by: Sean Eric Fagan <sef@ixsystems.com>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#898Closes#8987
Commit https://github.com/torvalds/linux/commit/3d745ea5 simplified
the blk_alloc_queue() interface by updating it to take the request
queue as an argument. Add a wrapper function which accepts the new
arguments and internally uses the available interfaces.
Other minor changes include increasing the Linux-Maximum to 5.6 now
that 5.6 has been released. It was not bumped to 5.7 because this
release has not yet been finalized and is still subject to change.
Added local 'struct zvol_state_os *zso' variable to zvol_alloc.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#10181Closes#10187
When configuring as builtin (--enable-linux-builtin) for kernels
without loadable module support (CONFIG_MODULES=n) only the object
file is created. Never a loadable kmod.
Update ZFS_LINUX_TRY_COMPILE to handle this in a manor similar to
the ZFS_LINUX_TEST_COMPILE_ALL macro.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9887Closes#10063
Commit https://github.com/torvalds/linux/commit/9e8d42a0f accidentally
converted the static inline function blkg_tryget() to GPL-only for
kernels built with CONFIG_PREEMPT_RCU=y and CONFIG_BLK_CGROUP=y.
Resolve the build issue by providing our own equivalent functionality
when needed which uses rcu_read_lock_sched() internally as before.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9745Closes#10072
The getrawmonotonic() and getrawmonotonic64() interfaces have been
fully retired. Update gethrtime() to use the replacement interface
ktime_get_raw_ts64() which was introduced in the 4.18 kernel.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#10052Closes#10064
This PR fixes an issue wherein redirecting stdout and stderr when
building kernel modules in configure tests relied on a bashism that
does not work as expected when /bin/sh is not bash.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-By: Richard Laager <rlaager@wiktel.com>
Signed-off-by: Andrew J. Hesford <ajh@sideband.org>
Closes#9990Closes#9998
Currently SIMD accelerated AES-GCM performance is limited by two
factors:
a. The need to disable preemption and interrupts and save the FPU
state before using it and to do the reverse when done. Due to the
way the code is organized (see (b) below) we have to pay this price
twice for each 16 byte GCM block processed.
b. Most processing is done in C, operating on single GCM blocks.
The use of SIMD instructions is limited to the AES encryption of the
counter block (AES-NI) and the Galois multiplication (PCLMULQDQ).
This leads to the FPU not being fully utilized for crypto
operations.
To solve (a) we do crypto processing in larger chunks while owning
the FPU. An `icp_gcm_avx_chunk_size` module parameter was introduced
to make this chunk size tweakable. It defaults to 32 KiB. This step
alone roughly doubles performance. (b) is tackled by porting and
using the highly optimized openssl AES-GCM assembler routines, which
do all the processing (CTR, AES, GMULT) in a single routine. Both
steps together result in up to 32x reduction of the time spend in
the en/decryption routines, leading up to approximately 12x
throughput increase for large (128 KiB) blocks.
Lastly, this commit changes the default encryption algorithm from
AES-CCM to AES-GCM when setting the `encryption=on` property.
Reviewed-By: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-By: Jason King <jason.king@joyent.com>
Reviewed-By: Tom Caputi <tcaputi@datto.com>
Reviewed-By: Richard Laager <rlaager@wiktel.com>
Signed-off-by: Attila Fülöp <attila@fueloep.org>
Closes#9749
The timestamp_truncate() function was added, it replaces the existing
timespec64_trunc() function. This change renames our wrapper function
to be consistent with the upstream name and updates the compatibility
code for older kernels accordingly.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9956Closes#9961
The proc_ops structure was introduced to replace the use of of the
file_operations structure when registering proc handlers. This
change creates a new kstat_proc_op_t typedef for compatibility
which can be used to pass around the correct structure.
This change additionally adds the 'const' keyword to all of the
existing proc operations structures.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9961
Clang does not recognize -fno-ipa-sra, so add a check for it.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Prakash Surya <prakash.surya@delphix.com>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#9946
Be default, clang treats unknown warning option as warning.
We need to use -Werror to make it an error.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: 12101111 <w12101111@gmail.com>
Closes#9927
To better enable dynamic tracing tools (e.g. "bpftrace") this change
disables the "-fipa-sra" compilation optimization. This way, function
signatures are not changed by the compiler, which allows us to better
attach to kprobes and kretprobes with dynamic tracing tools. Otherwise,
the compiler may append ".isra" to the function name, and possibly
change the function arguments as well.
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Prakash Surya <prakash.surya@delphix.com>
Closes#9921
Over the years several slightly different approaches were used
in the Makefiles to determine the target architecture. This
change updates both the build system and Makefile to handle
this in a consistent fashion.
TARGET_CPU is set to i386, x86_64, powerpc, aarch6 or sparc64
and made available in the Makefiles to be used as appropriate.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9848
Rely on ax_code_coverage to exclude test directories.
- Removes broken codecov ignore
- Places ignore section in ax_code_coverage
- Forwards users from codecov to LCOV for ignores
Reviewed-by: Prakash Surya <prakash.surya@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Signed-off-by: Kjeld Schouten-Lebbing <kjeld@schouten-lebbing.nl>
Closes#9726
As described in commit f81d5ef6 the zfs_vdev_elevator module
option is being removed. Users who require this functionality
should update their systems to set the disk scheduler using a
udev rule.
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #8664Closes#9417Closes#9609
Reinstate the zpl_revalidate() functionality to resolve a regression
where dentries for open files during a rollback are not invalidated.
The unrelated functionality for automatically unmounting .zfs/snapshots
was not reverted. Nor was the addition of shrink_dcache_sb() to the
zfs_resume_fs() function.
This issue was not immediately caught by the CI because the test case
intended to catch it was included in the list of ZTS tests which may
occasionally fail for unrelated reasons. Remove all of the rollback
tests from this list to help identify the frequency of any spurious
failures.
The rollback_003_pos.ksh test case exposes a real issue with the
long standing code which needs to be investigated. Regardless,
it has been enable with a small workaround in the test case itself.
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Pavel Snajdr <snajpa@snajpa.net>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9587Closes#9592
This patch implements use of kvmalloc for GFP_KERNEL allocations, which
may increase performance if the allocator is able to allocate physical
memory, if kvmalloc is available as a public kernel interface (since
v4.12). Otherwise it will simply fall back to virtual memory (vmalloc).
Also fix vmem_alloc implementation which can lead to slow allocations
since the first attempt with kmalloc does not make use of the noretry
flag but tells the linux kernel to retry several times before it fails.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Ahrens <matt@delphix.com>
Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Closes#9034
Increase the minimum supported kernel version from 2.6.32 to 3.10.
This removes support for the following Linux enterprise distributions.
Distribution | Kernel | End of Life
---------------- | ------ | -------------
Ubuntu 12.04 LTS | 3.2 | Apr 28, 2017
SLES 11 | 3.0 | Mar 32, 2019
RHEL / CentOS 6 | 2.6.32 | Nov 30, 2020
The following changes were made as part of removing support.
* Updated `configure` to enforce a minimum kernel version as
specified in the META file (Linux-Minimum: 3.10).
configure: error:
*** Cannot build against kernel version 2.6.32.
*** The minimum supported kernel version is 3.10.
* Removed all `configure` kABI checks and matching C code for
interfaces which solely predate the Linux 3.10 kernel.
* Updated all `configure` kABI checks to fail when an interface is
missing which was in the 3.10 kernel up to the latest 5.1 kernel.
Removed the HAVE_* preprocessor defines for these checks and
updated the code to unconditionally use the verified interface.
* Inverted the detection logic in several kABI checks to match
the new interface as it appears in 3.10 and newer and not the
legacy interface.
* Consolidated the following checks in to individual files. Due
the large number of changes in the checks it made sense to handle
this now. It would be desirable to group other related checks in
the same fashion, but this as left as future work.
- config/kernel-blkdev.m4 - Block device kABI checks
- config/kernel-blk-queue.m4 - Block queue kABI checks
- config/kernel-bio.m4 - Bio interface kABI checks
* Removed the kABI checks for sops->nr_cached_objects() and
sops->free_cached_objects(). These interfaces are currently unused.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9566
This patch removes the need for zpl_revalidate altogether.
There were 3 main reasons why we used d_revalidate:
1. periodic automounted snapshots umount deferral
2. negative dentries created before snapshot rollback
3. stale inodes referenced by dentry cache after snapshot rollback
Periodic snapshots deferral solution introduces zfs_exit_fs function,
which is called as a part of ZFS_EXIT(zfsvfs_t) macro.
Negative dentries and stale inodes are solved by flushing the dcache
for the particular dataset on zfs_resume_fs call.
This patch also removes now unused HAVE_S_D_OP configure test.
Reviewed-by: Aleksa Sarai <cyphar@cyphar.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Pavel Snajdr <snajpa@snajpa.net>
Closes#8774Closes#9549
Contrary to initial testing we cannot rely on these kernels to
invalidate the per-cpu FPU state and restore the FPU registers.
Nor can we guarantee that the kernel won't modify the FPU state
which we saved in the task struck.
Therefore, the kfpu_begin() and kfpu_end() functions have been
updated to save and restore the FPU state using our own dedicated
per-cpu FPU state variables.
This has the additional advantage of allowing us to use the FPU
again in user threads. So we remove the code which was added to
use task queues to ensure some functions ran in kernel threads.
Reviewed-by: Fabian Grünbichler <f.gruenbichler@proxmox.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #9346Closes#9403
Not all versions of sed have the --in-place flag. Detect support for
the flag during ./configure and provide a fallback mechanism for those
systems where sed's behavior differs. The autoconf variable
${ac_inplace} can be used to choose the correct flags for editing a
file in place with sed.
Replace violating usages in Makefile.am with ${ac_inplace}.
Reviewed-by: Chris Dunlop <chris@onthe.net.au>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#9463
Factor Linux specific pieces out of libspl.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Sean Eric Fagan <sef@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9336
Reduce the time required for ./configure to perform the needed
KABI checks by allowing kbuild to compile multiple test cases in
parallel. This was accomplished by splitting each test's source
code from the logic handling whether that code could be compiled
or not.
By introducing this split it's possible to minimize the number of
times kbuild needs to be invoked. As importantly, it means all of
the tests can be built in parallel. This does require a little extra
care since we expect some tests to fail, so the --keep-going (-k)
option must be provided otherwise some tests may not get compiled.
Furthermore, since a failure during the kbuild modpost phase will
result in an early exit; the final linking phase is limited to tests
which passed the initial compilation and produced an object file.
Once everything has been built the configure script proceeds as
previously. The only significant difference is that it now merely
needs to test for the existence of a .ko file to determine the
result of a given test. This vastly speeds up the entire process.
New test cases should use ZFS_LINUX_TEST_SRC to declare their test
source code and ZFS_LINUX_TEST_RESULT to check the result. All of
the existing kernel-*.m4 files have been updated accordingly, see
config/kernel-current-time.m4 for a basic example. The legacy
ZFS_LINUX_TRY_COMPILE macro has been kept to handle special cases
but it's use is not encouraged.
master (secs) patched (secs)
------------- ----------------
autogen.sh 61 68
configure 137 24 (~17% of current run time)
make -j $(nproc) 44 44
make rpms 287 150
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8547Closes#9132Closes#9341
Move platform specific Linux headers under include/os/linux/.
Update the build system accordingly to detect the platform.
This lays some of the initial groundwork to supporting building
for other platforms.
As part of this change it was necessary to create both a user
and kernel space sys/simd.h header which can be included in
either context. No functional change, the source has been
refactored and the relevant #include's updated.
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Signed-off-by: Matthew Macy <mmacy@FreeBSD.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9198
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Closes#9232
Resolve an assortment of style inconsistencies including
use of white space, typos, capitalization, and line wrapping.
There is no functional change.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9030
Restore the SIMD optimization for 4.19.38 LTS, 4.14.120 LTS,
and 5.0 and newer kernels. This is accomplished by leveraging
the fact that by definition dedicated kernel threads never need
to concern themselves with saving and restoring the user FPU state.
Therefore, they may use the FPU as long as we can guarantee user
tasks always restore their FPU state before context switching back
to user space.
For the 5.0 and 5.1 kernels disabling preemption and local
interrupts is sufficient to allow the FPU to be used. All non-kernel
threads will restore the preserved user FPU state.
For 5.2 and latter kernels the user FPU state restoration will be
skipped if the kernel determines the registers have not changed.
Therefore, for these kernels we need to perform the additional
step of saving and restoring the FPU registers. Invalidating the
per-cpu global tracking the FPU state would force a restore but
that functionality is private to the core x86 FPU implementation
and unavailable.
In practice, restricting SIMD to kernel threads is not a major
restriction for ZFS. The vast majority of SIMD operations are
already performed by the IO pipeline. The remaining cases are
relatively infrequent and can be handled by the generic code
without significant impact. The two most noteworthy cases are:
1) Decrypting the wrapping key for an encrypted dataset,
i.e. `zfs load-key`. All other encryption and decryption
operations will use the SIMD optimized implementations.
2) Generating the payload checksums for a `zfs send` stream.
In order to avoid making any changes to the higher layers of ZFS
all of the `*_get_ops()` functions were updated to take in to
consideration the calling context. This allows for the fastest
implementation to be used as appropriate (see kfpu_allowed()).
The only other notable instance of SIMD operations being used
outside a kernel thread was at module load time. This code
was moved in to a taskq in order to accommodate the new kernel
thread restriction.
Finally, a few other modifications were made in order to further
harden this code and facilitate testing. They include updating
each implementations operations structure to be declared as a
constant. And allowing "cycle" to be set when selecting the
preferred ops in the kernel as well as user space.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8754Closes#8793Closes#8965
This commit ensures make(1) targets that build .deb packages fail if
alien(1) can't convert all .rpm files; additionally it also updates
the zfs-dracut package name which was changed to "noarch" in ca4e5a7.
Reviewed-by: Neal Gompa <ngompa@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#8990Closes#8991
Don't require Python at configure/build unless building pyzfs.
Move ZFS_AC_PYTHON_MODULE to always-pyzfs.m4 where it is used.
Make test syntax more consistent.
Sponsored by: iXsystems, Inc.
Reviewed-by: Neal Gompa <ngompa@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#8895
If ZFS is built with enable_linux_builtin, it seems to be possible
to compile the kernel with TRIM_UNUSED_KSYM.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Torsten Wörtwein <twoertwein@gmail.com>
Closes#8820
Previously, --without-python would cause ./configure to fail. Now it is
able to proceed, and the Python scripts will not be built.
Use portable parameter expansion matching instead of nonstandard
substring matching to detect the Python version. This test is
duplicated in several places, so define a function for it.
Don't assume the full path to binaries, since different platforms do
install things in different places. Use AC_CHECK_PROGS instead.
When building without Python, also build without pyzfs.
Sponsored by: iXsystems, Inc.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Eli Schwartz <eschwartz93@gmail.com>
Signed-off-by: Ryan Moeller <ryan@freqlabs.com>
Closes#8809Closes#8731
Per suggestion from @behlendorf in #8777, remove vn_set_fs_pwd() and
vn_set_pwd() which are only used in zfs_ioctl.c:_init() while loading
zfs.ko.
The rest of initialization functions being called here after cwd set
to / don't depend on cwd of the process except for spa_config_load().
spa_config_load() uses a relative path ".//etc/zfs/zpool.cache" when
`rootdir` is non-NULL, which is "/etc/zfs/zpool.cache" given cwd is /,
so just unconditionally use the absolute path without "./", so that
`vn_set_pwd("/")` as well as the entire functions can be removed.
This is also what FreeBSD does.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@osnexus.com>
Closes#8826
