GRUB is not able to detect ZFS pool if snaphsot of top level boot
pool is created. This issue is observed with GRUB versions up to
v2.06 if extensible_dataset feature is enabled on ZFS boot pool.
compatibility=grub2-2.06 would enable all read-only compatible
zpool features except extensible_dataset and other features that
depend on it.
The existing grub2 compatibility file is now renamed to grub2-2.12 to
reflect the appropriate grub2 version. grub2-2.12 lists all read-only
features that can be enabled on boot pool for grub2 with version 2.12
onwards.
A new symlink grub2 is created that currently points to the grub2-2.12
compatibility file.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Umer Saleem <usaleem@ixsystems.com>
Closes#13873Closes#15261Closes#15909
Adding O_DIRECT support to ZFS to bypass the ARC for writes/reads.
O_DIRECT support in ZFS will always ensure there is coherency between
buffered and O_DIRECT IO requests. This ensures that all IO requests,
whether buffered or direct, will see the same file contents at all
times. Just as in other FS's , O_DIRECT does not imply O_SYNC. While
data is written directly to VDEV disks, metadata will not be synced
until the associated TXG is synced.
For both O_DIRECT read and write request the offset and request sizes,
at a minimum, must be PAGE_SIZE aligned. In the event they are not,
then EINVAL is returned unless the direct property is set to always (see
below).
For O_DIRECT writes:
The request also must be block aligned (recordsize) or the write
request will take the normal (buffered) write path. In the event that
request is block aligned and a cached copy of the buffer in the ARC,
then it will be discarded from the ARC forcing all further reads to
retrieve the data from disk.
For O_DIRECT reads:
The only alignment restrictions are PAGE_SIZE alignment. In the event
that the requested data is in buffered (in the ARC) it will just be
copied from the ARC into the user buffer.
For both O_DIRECT writes and reads the O_DIRECT flag will be ignored in
the event that file contents are mmap'ed. In this case, all requests
that are at least PAGE_SIZE aligned will just fall back to the buffered
paths. If the request however is not PAGE_SIZE aligned, EINVAL will
be returned as always regardless if the file's contents are mmap'ed.
Since O_DIRECT writes go through the normal ZIO pipeline, the
following operations are supported just as with normal buffered writes:
Checksum
Compression
Encryption
Erasure Coding
There is one caveat for the data integrity of O_DIRECT writes that is
distinct for each of the OS's supported by ZFS.
FreeBSD - FreeBSD is able to place user pages under write protection so
any data in the user buffers and written directly down to the
VDEV disks is guaranteed to not change. There is no concern
with data integrity and O_DIRECT writes.
Linux - Linux is not able to place anonymous user pages under write
protection. Because of this, if the user decides to manipulate
the page contents while the write operation is occurring, data
integrity can not be guaranteed. However, there is a module
parameter `zfs_vdev_direct_write_verify` that controls the
if a O_DIRECT writes that can occur to a top-level VDEV before
a checksum verify is run before the contents of the I/O buffer
are committed to disk. In the event of a checksum verification
failure the write will return EIO. The number of O_DIRECT write
checksum verification errors can be observed by doing
`zpool status -d`, which will list all verification errors that
have occurred on a top-level VDEV. Along with `zpool status`, a
ZED event will be issues as `dio_verify` when a checksum
verification error occurs.
ZVOLs and dedup is not currently supported with Direct I/O.
A new dataset property `direct` has been added with the following 3
allowable values:
disabled - Accepts O_DIRECT flag, but silently ignores it and treats
the request as a buffered IO request.
standard - Follows the alignment restrictions outlined above for
write/read IO requests when the O_DIRECT flag is used.
always - Treats every write/read IO request as though it passed
O_DIRECT and will do O_DIRECT if the alignment restrictions
are met otherwise will redirect through the ARC. This
property will not allow a request to fail.
There is also a module parameter zfs_dio_enabled that can be used to
force all reads and writes through the ARC. By setting this module
parameter to 0, it mimics as if the direct dataset property is set to
disabled.
Reviewed-by: Brian Behlendorf <behlendorf@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Atkinson <batkinson@lanl.gov>
Co-authored-by: Mark Maybee <mark.maybee@delphix.com>
Co-authored-by: Matt Macy <mmacy@FreeBSD.org>
Co-authored-by: Brian Behlendorf <behlendorf@llnl.gov>
Closes#10018
Requires the new 'flat' physical data which has the start
time for a class entry.
The amount to prune can be based on a target percentage of
the unique entries or based on the age (i.e., every entry
older than N days).
Sponsored-by: Klara, Inc.
Sponsored-by: iXsystems, Inc.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@klarasystems.com>
Closes#16277
This commit extends the zpool-reguid(8) command with a -g flag, which
allows the user to specify the GUID to set.
This change also adds some general tests for zpool-reguid(8).
Sponsored-by: Wasabi Technology, Inc.
Sponsored-by: Klara, Inc.
Signed-off-by: Mateusz Piotrowski <0mp@FreeBSD.org>
Reviewed-by: Rob Norris <rob.norris@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
This fixes things so mirrored special vdevs report themselves as
"class=special" rather than "class=normal".
This happens due to the way the vdev nvlists are constructed:
mirrored special devices - The 'mirror' vdev has allocation bias as
"special" and it's leaf vdevs are "normal"
single or RAID0 special devices - Leaf vdevs have allocation bias as
"special".
This commit adds in code to check if a leaf's parent is a "special"
vdev to see if it should also report "special".
Reviewed-by: Ameer Hamza <ahamza@ixsystems.com>
Reviewed-by: Umer Saleem <usaleem@ixsystems.com>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#16217
This commit adds support for zpool status command to displpay status
of ZFS pools in JSON format using '-j' option. Status information is
collected in nvlist which is later dumped on stdout in JSON format.
Existing options for zpool status work with '-j' flag. man page for
zpool status is updated accordingly.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Ameer Hamza <ahamza@ixsystems.com>
Signed-off-by: Umer Saleem <usaleem@ixsystems.com>
Closes#16217
This commit adds support for zpool list command to output the list of
ZFS pools in JSON format using '-j' option.. Information about available
pools is collected in nvlist which is later printed to stdout in JSON
format.
Existing options for zfs list command work with '-j' flag. man page for
zpool list is updated accordingly.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Ameer Hamza <ahamza@ixsystems.com>
Signed-off-by: Umer Saleem <usaleem@ixsystems.com>
Closes#16217
This commit adds support for zpool get command to output the list of
properties for ZFS Pools and VDEVS in JSON format using '-j' option.
Man page for zpool get is updated to include '-j' option.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Ameer Hamza <ahamza@ixsystems.com>
Signed-off-by: Umer Saleem <usaleem@ixsystems.com>
Closes#16217
This commit adds support for zpool version to output in JSON format
using '-j' option. Userland kernel module version is collected in nvlist
which is later displayed in JSON format. man page for zpool is updated.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Ameer Hamza <ahamza@ixsystems.com>
Signed-off-by: Umer Saleem <usaleem@ixsystems.com>
Closes#16217
This change adds a new `zpool prefetch -t ddt $pool` command which
causes a pool's DDT to be loaded into the ARC. The primary goal is to
remove the need to "warm" a pool's cache before deduplication stops
slowing write performance. It may also provide a way to reload portions
of a DDT if they have been flushed due to inactivity.
Sponsored-by: iXsystems, Inc.
Sponsored-by: Catalogics, Inc.
Sponsored-by: Klara, Inc.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Will Andrews <will.andrews@klarasystems.com>
Signed-off-by: Fred Weigel <fred.weigel@klarasystems.com>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Signed-off-by: Don Brady <don.brady@klarasystems.com>
Co-authored-by: Will Andrews <will.andrews@klarasystems.com>
Co-authored-by: Don Brady <don.brady@klarasystems.com>
Closes#15890
The 'zpool status' output assumes that the longest prefix is six
character long plus colon plus space, eg. 'status: ', 'action: '
or 'config: ' (so eight in total). This works well even when we have
messages that requires more than one line, as '\t' is exactly eight
characters, just like the longest prefix.
The 'zpool import' output is a bit different, as it may display the
comment pool property, then the longest prefix is 'comment: ', which is
nine characters long, not eight.
All the prefixes were given an extra space in front, but:
- 'status: ' did not get an extra space.
- Messages that require more than one line should use nine spaces of
indentation, not eight.
- The extra space in front looks redundant if there is no comment
property set on the given pool.
Fix it by adding an extra space to all prefixes, but only if the comment
property is defined. Also, when we need to continue the message in a new
line, use '\t ' for indentation.
While here, apply small corrections to a couple messages.
Before:
pool: tank
id: 7412636063178848859
state: ONLINE
status: Some supported features are not enabled on the pool.
(Note that they may be intentionally disabled if the
'compatibility' property is set.)
action: The pool can be imported using its name or numeric identif[...]
some features will not be available without an explicit 'zp[...]
comment: Example comment.
config:
bclone ONLINE
ada0 ONLINE
After:
pool: tank
id: 10180960571062436759
state: ONLINE
status: Some supported features are not enabled on the pool.
(Note that they may be intentionally disabled if the
'compatibility' property is set.)
action: The pool can be imported using its name or numeric identifi[...]
some features will not be available without an explicit 'zp[...]
config:
tank ONLINE
ada3 ONLINE
pool: dozer
id: 11028319538368222579
state: ONLINE
status: Some supported features are not enabled on the pool.
(Note that they may be intentionally disabled if the
'compatibility' property is set.)
action: The pool can be imported using its name or numeric identif[...]
some features will not be available without an explicit 'z[...]
comment: Example comment.
config:
dozer ONLINE
ada1 ONLINE
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Pawel Dawidek <pawel@dawidek.net>
Closes#16128
Ever since a10d50f999, ZFS has mounted file systems in parallel when
importing a pool. It uses a fixed size of 512 for the thread pool. But
since c183d164aa, it has also imported pools in parallel. So the total
number of threads at one time is 513 * npools + 1. That can easily
exceed the system's limit on the number of threads per process, which
will cause one or more pools to be unable to allocate any worker
threads, forcing them to fallback to slow serial mounting . To
forestall that, manage the threadpool size in /sbin/zpool, not libzfs.
Use the same size (512), but divided by the number of pools.
This is a backwards-incompatible change to the libzfs abi.
Sponsored by: Axcient
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Wilson <gwilson@delphix.com>
Signed-off-by: Alan Somers <asomers@FreeBSD.org>
Closes#16178
Changed spa_export_common() such that it no longer holds the
spa_namespace_lock for the entire duration and instead sets
spa_export_thread to indicate an import is in progress on the
spa. This allows for an export to a diffent pool to proceed
in parallel while an export is still processing potentially
long operations like spa_unload_log_sm_flush_all().
Calls like spa_lookup() and spa_vdev_enter() that rely on
the spa_namespace_lock to serialize them against a concurrent
export, now wait for any in-progress export thread to complete
before proceeding.
The 'zpool import -a' sub-command also provides multi-threaded
support, using a thread pool to submit the exports in parallel.
Sponsored-By: Klara Inc.
Sponsored-by: Wasabi Technology, Inc.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Wilson <gwilson@delphix.com>
Signed-off-by: Don Brady <don.brady@klarasystems.com>
Closes#16153
Simplify vdev probes in the zio_vdev_io_done context to
avoid holding the spa config lock for a long duration.
Also allow zpool clear if no evidence of another host
is using the pool.
Sponsored-by: Klara, Inc.
Sponsored-by: Wasabi Technology, Inc.
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@klarasystems.com>
Closes#15839
- Workaround dangling pointer in uu_list.c (#16124)
- Fix calloc() transposed arguments in zpool_vdev_os.c
- Make some temp variables unsigned to prevent triggering a
'-Werror=alloc-size-larger-than' error.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#16124Closes#16125
This commit allow spa_load() to drop the spa_namespace_lock so
that imports can happen concurrently. Prior to dropping the
spa_namespace_lock, the import logic will set the spa_load_thread
value to track the thread which is doing the import.
Consumers of spa_lookup() retain the same behavior by blocking
when either a thread is holding the spa_namespace_lock or the
spa_load_thread value is set. This will ensure that critical
concurrent operations cannot take place while a pool is being
imported.
The zpool command is also enhanced to provide multi-threaded support
when invoking zpool import -a.
Lastly, zinject provides a mechanism to insert artificial delays
when importing a pool and new zfs tests are added to verify parallel
import functionality.
Contributions-by: Don Brady <don.brady@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Wilson <gwilson@delphix.com>
Closes#16093
In `zpool status -t`, scrub date/time is reported using the C locale,
while trim time is reported using the current one. This is inconsistent.
This patch fixes that.
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Maxim Filimonov <che@bein.link>
Closes#15878Closes#15879
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Don Brady <don.brady@klarasystems.com>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#15942
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Jason Lee <jasonlee@lanl.gov>
Signed-off-by: Robert Evans <evansr@google.com>
Closes#16028Closes#16035
Currently, zpool add allows users to add top-level vdevs that have
different ashifts but doing so prevents users from being able to
perform a top-level vdev removal. Often times consumers may not realize
that they have mismatched ashifts until the top-level removal fails.
This feature adds ashift validation to the zpool add command and will
fail the operation if the sector size of the specified vdev does not
match the existing pool. This behavior can be disabled by using the -f
flag. In addition, new flags have been added to provide fine-grained
control to disable specific checks. These flags
are:
--allow-in-use
--allow-ashift-mismatch
--allow-replicaton-mismatch
The force flag will disable all of these checks.
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Mark Maybee <mmaybee@delphix.com>
Signed-off-by: George Wilson <gwilson@delphix.com>
Closes#15509
The recently added '-e' option (PR #15769) missed adding the
new option in the online `zpool status` help command. This
adds the options and reorders a couple of the other options
that were not listed alphabetically.
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Cameron Harr <harr1@llnl.gov>
Closes#16008
Slow disk response times can be indicative of a failing drive. ZFS
currently tracks slow I/Os (slower than zio_slow_io_ms) and generates
events (ereport.fs.zfs.delay). However, no action is taken by ZED,
like is done for checksum or I/O errors. This change adds slow disk
diagnosis to ZED which is opt-in using new VDEV properties:
VDEV_PROP_SLOW_IO_N
VDEV_PROP_SLOW_IO_T
If multiple VDEVs in a pool are undergoing slow I/Os, then it skips
the zpool_vdev_degrade().
Sponsored-By: OpenDrives Inc.
Sponsored-By: Klara Inc.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Rob Wing <rob.wing@klarasystems.com>
Signed-off-by: Don Brady <don.brady@klarasystems.com>
Closes#15469
When very large pools are present, it can be laborious to find
reasons for why a pool is degraded and/or where an unhealthy vdev
is. This option filters out vdevs that are ONLINE and with no errors
to make it easier to see where the issues are. Root and parents of
unhealthy vdevs will always be printed.
Testing:
ZFS errors and drive failures for multiple vdevs were simulated with
zinject.
Sample vdev listings with '-e' option
- All vdevs healthy
NAME STATE READ WRITE CKSUM
iron5 ONLINE 0 0 0
- ZFS errors
NAME STATE READ WRITE CKSUM
iron5 ONLINE 0 0 0
raidz2-5 ONLINE 1 0 0
L23 ONLINE 1 0 0
L24 ONLINE 1 0 0
L37 ONLINE 1 0 0
- Vdev faulted
NAME STATE READ WRITE CKSUM
iron5 DEGRADED 0 0 0
raidz2-6 DEGRADED 0 0 0
L67 FAULTED 0 0 0 too many errors
- Vdev faults and data errors
NAME STATE READ WRITE CKSUM
iron5 DEGRADED 0 0 0
raidz2-1 DEGRADED 0 0 0
L2 FAULTED 0 0 0 too many errors
raidz2-5 ONLINE 1 0 0
L23 ONLINE 1 0 0
L24 ONLINE 1 0 0
L37 ONLINE 1 0 0
raidz2-6 DEGRADED 0 0 0
L67 FAULTED 0 0 0 too many errors
- Vdev missing
NAME STATE READ WRITE CKSUM
iron5 DEGRADED 0 0 0
raidz2-6 DEGRADED 0 0 0
L67 UNAVAIL 3 1 0
- Slow devices when -s provided with -e
NAME STATE READ WRITE CKSUM SLOW
iron5 DEGRADED 0 0 0 -
raidz2-5 DEGRADED 0 0 0 -
L10 FAULTED 0 0 0 0 external device fault
L51 ONLINE 0 0 0 14
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Cameron Harr <harr1@llnl.gov>
Closes#15769
list, status and iostat all display the -T timestamp before the header,
but wait showed it after. Make it be like the others.
Reported-by: Kyle Evans <kevans@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <robn@despairlabs.com>
Closes#15825
- Mark some parameters to zpool_power*() as unused.
- Add a stub zpool_disk_wait().
Fixes: a9520e6e5 ("zpool: Add slot power control, print power status")
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Add `zpool` flags to control the slot power to drives. This assumes
your SAS or NVMe enclosure supports slot power control via sysfs.
The new `--power` flag is added to `zpool offline|online|clear`:
zpool offline --power <pool> <device> Turn off device slot power
zpool online --power <pool> <device> Turn on device slot power
zpool clear --power <pool> [device] Turn on device slot power
If the ZPOOL_AUTO_POWER_ON_SLOT env var is set, then the '--power'
option is automatically implied for `zpool online` and `zpool clear`
and does not need to be passed.
zpool status also gets a --power option to print the slot power status.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mart Frauenlob <AllKind@fastest.cc>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#15662
Just silencing a warning. Its totally fine for a hostid to not be there.
Reported-by: Coverity (CID-1573336)
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ameer Hamza <ahamza@ixsystems.com>
Signed-off-by: Rob Norris <robn@despairlabs.com>
Closes#15650
Several zpool commands (status, list, iostat) have modes that present
some information, sleep a while, present the current state, sleep, etc.
Some of those had ways to invoke them that when piped would appear to do
nothing for a while, because non-terminals are block-buffered, not
line-buffered, by default. Fix this by forcing a flush before sleeping.
In particular, all of these buffered:
- zpool status <pool> <interval>
- zpool iostat -y<m> <pool> <interval>
- zpool list <pool> <interval>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <robn@despairlabs.com>
Closes#15593
zpool_create_features_007_pos only tested for compat-2020 feature
set. It would be useful to test for all known features sets. If
any additional feature is found enabled that is not present in
compatibility list or feature set, it should be caught and
reported earlier.
This commit also removes encryption from openzfsonosx-1.8.1
compatibility list. Encryption enables bookmark_v2, since it is
a dependency of encryption, but not listed in openzfsonoxx-1.8.1
compatibility list.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Umer Saleem <usaleem@ixsystems.com>
Closes#15505
This feature allows disks to be added one at a time to a RAID-Z group,
expanding its capacity incrementally. This feature is especially useful
for small pools (typically with only one RAID-Z group), where there
isn't sufficient hardware to add capacity by adding a whole new RAID-Z
group (typically doubling the number of disks).
== Initiating expansion ==
A new device (disk) can be attached to an existing RAIDZ vdev, by
running `zpool attach POOL raidzP-N NEW_DEVICE`, e.g. `zpool attach tank
raidz2-0 sda`. The new device will become part of the RAIDZ group. A
"raidz expansion" will be initiated, and the new device will contribute
additional space to the RAIDZ group once the expansion completes.
The `feature@raidz_expansion` on-disk feature flag must be `enabled` to
initiate an expansion, and it remains `active` for the life of the pool.
In other words, pools with expanded RAIDZ vdevs can not be imported by
older releases of the ZFS software.
== During expansion ==
The expansion entails reading all allocated space from existing disks in
the RAIDZ group, and rewriting it to the new disks in the RAIDZ group
(including the newly added device).
The expansion progress can be monitored with `zpool status`.
Data redundancy is maintained during (and after) the expansion. If a
disk fails while the expansion is in progress, the expansion pauses
until the health of the RAIDZ vdev is restored (e.g. by replacing the
failed disk and waiting for reconstruction to complete).
The pool remains accessible during expansion. Following a reboot or
export/import, the expansion resumes where it left off.
== After expansion ==
When the expansion completes, the additional space is available for use,
and is reflected in the `available` zfs property (as seen in `zfs list`,
`df`, etc).
Expansion does not change the number of failures that can be tolerated
without data loss (e.g. a RAIDZ2 is still a RAIDZ2 even after
expansion).
A RAIDZ vdev can be expanded multiple times.
After the expansion completes, old blocks remain with their old
data-to-parity ratio (e.g. 5-wide RAIDZ2, has 3 data to 2 parity), but
distributed among the larger set of disks. New blocks will be written
with the new data-to-parity ratio (e.g. a 5-wide RAIDZ2 which has been
expanded once to 6-wide, has 4 data to 2 parity). However, the RAIDZ
vdev's "assumed parity ratio" does not change, so slightly less space
than is expected may be reported for newly-written blocks, according to
`zfs list`, `df`, `ls -s`, and similar tools.
Sponsored-by: The FreeBSD Foundation
Sponsored-by: iXsystems, Inc.
Sponsored-by: vStack
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Authored-by: Matthew Ahrens <mahrens@delphix.com>
Contributions-by: Fedor Uporov <fuporov.vstack@gmail.com>
Contributions-by: Stuart Maybee <stuart.maybee@comcast.net>
Contributions-by: Thorsten Behrens <tbehrens@outlook.com>
Contributions-by: Fmstrat <nospam@nowsci.com>
Contributions-by: Don Brady <dev.fs.zfs@gmail.com>
Signed-off-by: Don Brady <dev.fs.zfs@gmail.com>
Closes#15022
PR#15459 add all read-only compatible zpool features to grub2
compatibility list. 'obsolete_counts' is a read-only features that
depends on 'device_removal' feature which is not read-only and
is marked as ZFEATURE_FLAG_MOS. Creating a pool with grub2
compatibility enables 'device_removal' feature as well, which is
not desired.
This commit removes the 'obsolete_counts' feature from
grub2 compatibility list, as GRUB only supports read-only
compatible features.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Umer Saleem <usaleem@ixsystems.com>
Closes#15499
There have been rare cases where the VDEV_ENC_SYSFS_PATH value that zed
gets passed is stale. To mitigate this, dynamically check the sysfs
path at the time of zed event processing, and use the dynamic value if
possible. Note that there will be other times when we can not
dynamically detect the sysfs path (like if a disk disappears) and have
to rely on the old value for things like turning on the fault LED. That
is to say, we can't just blindly use the dynamic path in every case.
Also:
- Add enclosure sysfs entry when running 'zpool add'
- Fix 'slot' and 'enc' zpool.d scripts for nvme
Reviewed-by: Don Brady <dev.fs.zfs@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#15462
GRUB opens the boot pool in read-only mode. All read-only
compatible features for zpool can be enabled and added to
grub2 compatibility, as GRUB does not open the boot-pool
for write.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Umer Saleem <usaleem@ixsystems.com>
Closes#15459
Previously, if a cachefile is passed to zpool import, the cached config
is mostly offered as-is to ZFS_IOC_POOL_TRYIMPORT->spa_tryimport(), and
the results are taken as the canonical pool config and handed back to
ZFS_IOC_POOL_IMPORT.
In the course of its operation, spa_load() will inspect the pool and
build a new config from what it finds on disk. However, it then
regenerates a new config ready to import, and so rightly sets the hostid
and hostname for the local host in the config it returns.
Because of this, the "require force" checks always decide the pool is
exported and last touched by the local host, even if this is not true,
which is possible in a HA environment when MMP is not enabled. The pool
may be imported on another head, but the import checks still pass here,
so the pool ends up imported on both.
(This doesn't happen when a cachefile isn't used, because the pool
config is discovered in userspace in zpool_find_import(), and that does
find the on-disk hostid and hostname correctly).
Since the systemd zfs-import-cache.service unit uses cachefile imports,
this can lead to a system returning after a crash with a "valid"
cachefile on disk and automatically, quietly, importing a pool that has
already been taken up by a secondary head.
This commit causes the on-disk hostid and hostname to be included in the
ZPOOL_CONFIG_LOAD_INFO item in the returned config, and then changes the
"force" checks for zpool import to use them if present.
This method should give no change in behaviour for old userspace on new
kernels (they won't know to look for the new config items) and for new
userspace on old kernels (the won't find the new config items).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Sponsored-by: Klara, Inc.
Sponsored-by: Wasabi Technology, Inc.
Closes#15290
Have libzfs call a special `zfs_prepare_disk` script before a disk is
included into the pool. The user can edit this script to add things
like a disk firmware update or a disk health check. Use of the script
is totally optional. See the zfs_prepare_disk manpage for full details.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#15243
'program help subcommand' is a reasonably common pattern for
multifunction command-line programs. This commit adds support for that
style to the zpool and zfs commands.
When run as 'zpool help [<topic>]' or 'zfs help [<topic>]', executes the
'man' program on the PATH with the most likely manpage name for the
requested topic: "zpool-<topic>" or "zfs-<topic>" for subcommands, or
"zpool<topic>" or "zfs<topic>" for the "concepts" and "props" topics.
If no topic is supplied, uses the top "zpool" or "zfs" pages.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Kay Pedersen <mail@mkwg.de>
Signed-off-by: Rob Norris <robn@despairlabs.com>
Closes#15288
For zpool import and zpool split, zpool_enable_datasets is called
to mount and share all datasets in a pool. If there is an error
while mounting or sharing any dataset in the pool, the status of
import or split is reported as failure. However, the changes do
show up in zpool list.
This commit updates the error reporting in zpool import and zpool
split path. More descriptive messages are shown to user in case
there is an error during mount or share. Errors in mount or share
do not effect the overall status of zpool import and zpool split.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Umer Saleem <usaleem@ixsystems.com>
Closes#15216
Scan process may skip blocks based on their birth time, DVA, etc.
Traditionally those blocks were accounted as issued, that caused
reporting of hugely over-inflated numbers, having nothing to do
with actual disk I/O. This change utilizes never used field in
struct dsl_scan_phys to account such skipped bytes, allowing to
report how much data were actually scrubbed/resilvered and what
is the actual I/O speed. While formally it is an on-disk format
change, it should be compatible both ways, so should not need a
feature flag.
This should partially address the same issue as c85ac731a0, but
from a different perspective, complementing it.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Akash B <akash-b@hpe.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#15007
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Mike Swanson <mikeonthecomputer@gmail.com>
Closes#14902
GRUB2 is compatible with all "read-only compatible" features,
so it is safe to add new features of this type to the grub2
compatibility list. We generally want to include all compatible
features, to minimize the differences between grub2-compatible
pools and no-compatibility pools.
Adding new properties `livelist` and `zpool_checkpoint` accordingly.
Also adding them to the man page which references this file as an
example, for consistency.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Colm Buckley <colm@tuatha.org>
Closes#14893
Add an openzfs-2.2 compatibility file for the next release.
Edon-R support has been enabled for FreeBSD removing the need
for different FreeBSD and Linux files. Symlinks for the -linux
and -freebsd names are created for any scripts expecting that
convention.
Additionally, a symlink for ubunutu-22.04 was added.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#14833
Added a flag '-e' in zpool scrub to scrub only blocks in error log. A
user can pause, resume and cancel the error scrub by passing additional
command line arguments -p -s just like a regular scrub. This involves
adding a new flag, creating new libzfs interfaces, a new ioctl, and the
actual iteration and read-issuing logic. Error scrubbing is executed in
multiple txg to make sure pool performance is not affected.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Co-authored-by: TulsiJain tulsi.jain@delphix.com
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#8995Closes#12355
zpool initialize functions well for touching every free byte...once.
But if we want to do it again, we're currently out of luck.
So let's add zpool initialize -u to clear it.
Co-authored-by: Rich Ercolani <rincebrain@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12451Closes#14873
Usage:
zpool set org.freebsd:comment="this is my pool" poolname
Tests are based on zfs_set's user property tests.
Also stop truncating property values at MAXNAMELEN, use ZFS_MAXPROPLEN.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Mateusz Piotrowski <mateusz.piotrowski@klarasystems.com>
Sponsored-by: Beckhoff Automation GmbH & Co. KG.
Sponsored-by: Klara Inc.
Closes#11680
And add it to the AVZ, this is not backwards compatible with older pools
due to an assertion in spa_sync() that verifies the number of ZAPs of
all vdevs matches the number of ZAPs in the AVZ.
Granted, the assertion only applies to #DEBUG builds - still, a feature
flag is introduced to avoid the assertion, com.klarasystems:vdev_zaps_v2
Notably, this allows to get/set properties on the root vdev:
% zpool set user:prop=value <pool> root-0
Before this commit, it was already possible to get/set properties on
top-level vdevs with the syntax <type>-<vdev_id> (e.g. mirror-0):
% zpool set user:prop=value <pool> mirror-0
This syntax also applies to the root vdev as it is is of type 'root'
with a vdev_id of 0, root-0. The keyword 'root' as an alias for
'root-0'.
The following tests have been added:
- zpool get all properties from root vdev
- zpool set a property on root vdev
- verify root vdev ZAP is created
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Wing <rob.wing@klarasystems.com>
Sponsored-by: Seagate Technology
Submitted-by: Klara, Inc.
Closes#14405
This inappropriate left-alignment was introduced in 7bb7b1f.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Signed-off-by: WHR <msl0000023508@gmail.com>
Closes#14751
f6a0dac84 modified the zfs_iter_* functions to take a new "flags"
parameter, and introduced a variety of flags to ask the kernel to limit
the results in various ways, reducing the amount of work the caller
needed to do to filter out things they didn't need.
Unfortunately this change broke the ABI for existing clients (read:
older versions of the `zfs` program), and was reverted 399b98198.
dc95911d2 reintroduced the original patch, with the understanding that a
backwards-compatible fix would be made before the 2.2 release branch was
tagged. This commit is that fix.
This introduces zfs_iter_*_v2 functions that have the new flags
argument, and reverts the existing functions to not have the flags
parameter, as they were before. The old functions are now reimplemented
in terms of the new, with flags set to 0.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Wilson <george.wilson@delphix.com>
Original-patch-by: George Wilson <george.wilson@delphix.com>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Sponsored-by: Klara, Inc.
Closes#14597
When a vdev is degraded or faulted, we refuse to expand it when doing
online -e. However, we also don't actually cause the online command
to fail, even though the disk didn't expand. This is confusing and
misleading, and can result in violated expectations.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes 14145
