zfs umount -> zfsctl_destroy() takes the zfs_snapshot_lock as a
writer and calls zfsctl_snapshot_unmount_cancel(), which waits
for snapentry_expire() if present (when snap is automounted).
This snapentry_expire() itself then waits for zfs_snapshot_lock
as a reader, resulting in a deadlock.
The fix is to only hold the zfs_snapshot_lock over the tree
lookup and removal. After a successful lookup the lock can
be dropped and zfs_snapentry_t will remain valid until the
reference taken by the lookup is released.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rohan Puri <rohan.puri15@gmail.com>
Closes#7751Closes#7752
Overview
========
We parallelize the allocation process by creating the concept of
"allocators". There are a certain number of allocators per metaslab
group, defined by the value of a tunable at pool open time. Each
allocator for a given metaslab group has up to 2 active metaslabs; one
"primary", and one "secondary". The primary and secondary weight mean
the same thing they did in in the pre-allocator world; primary metaslabs
are used for most allocations, secondary metaslabs are used for ditto
blocks being allocated in the same metaslab group. There is also the
CLAIM weight, which has been separated out from the other weights, but
that is less important to understanding the patch. The active metaslabs
for each allocator are moved from their normal place in the metaslab
tree for the group to the back of the tree. This way, they will not be
selected for use by other allocators searching for new metaslabs unless
all the passive metaslabs are unsuitable for allocations. If that does
happen, the allocators will "steal" from each other to ensure that IOs
don't fail until there is truly no space left to perform allocations.
In addition, the alloc queue for each metaslab group has been broken
into a separate queue for each allocator. We don't want to dramatically
increase the number of inflight IOs on low-end systems, because it can
significantly increase txg times. On the other hand, we want to ensure
that there are enough IOs for each allocator to allow for good
coalescing before sending the IOs to the disk. As a result, we take a
compromise path; each allocator's alloc queue max depth starts at a
certain value for every txg. Every time an IO completes, we increase the
max depth. This should hopefully provide a good balance between the two
failure modes, while not dramatically increasing complexity.
We also parallelize the spa_alloc_tree and spa_alloc_lock, which cause
very similar contention when selecting IOs to allocate. This
parallelization uses the same allocator scheme as metaslab selection.
Performance Results
===================
Performance improvements from this change can vary significantly based
on the number of CPUs in the system, whether or not the system has a
NUMA architecture, the speed of the drives, the values for the various
tunables, and the workload being performed. For an fio async sequential
write workload on a 24 core NUMA system with 256 GB of RAM and 8 128 GB
SSDs, there is a roughly 25% performance improvement.
Future Work
===========
Analysis of the performance of the system with this patch applied shows
that a significant new bottleneck is the vdev disk queues, which also
need to be parallelized. Prototyping of this change has occurred, and
there was a performance improvement, but more work needs to be done
before its stability has been verified and it is ready to be upstreamed.
Authored by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Serapheim Dimitropoulos <serapheim.dimitro@delphix.com>
Reviewed by: Alexander Motin <mav@FreeBSD.org>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Gordon Ross <gwr@nexenta.com>
Ported-by: Paul Dagnelie <pcd@delphix.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Porting Notes:
* Fix reservation test failures by increasing tolerance.
OpenZFS-issue: https://illumos.org/issues/9112
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/3f3cc3c3Closes#7682
The zfs-dracut package requires the hostid, basename, head, awk,
and grep utilities be installed. The first three are provided by
coreutils but additional dependencies are required for awk and grep.
Reviewed-by: Manuel Amador (Rudd-O) <rudd-o@rudd-o.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7729Closes#7747
The new zfs-import.target should be used in place of the
zfs-import-*.service units.
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Manuel Amador (Rudd-O) <rudd-o@rudd-o.com>
Signed-off-by: Antonio Russo <antonio.e.russo@gmail.com>
Closes#6964
In the case of one pool being built on another pool, we want
to make sure we don't end up throttling the lower (backing)
pool when the upper pool is the majority contributor to dirty
data. To insure we make forward progress during throttling, we
also check the current pool's net dirty data and only throttle
if it exceeds zfs_arc_pool_dirty_percent of the anonymous dirty
data in the cache.
Authored by: Don Brady <don.brady@delphix.com>
Reviewed by: Sebastien Roy <sebastien.roy@delphix.com>
Reviewed by: Matt Ahrens <matt@delphix.com>
Reviewed by: Prashanth Sreenivasa <pks@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Porting Notes:
* The new global variables zfs_arc_dirty_limit_percent,
zfs_arc_anon_limit_percent, and zfs_arc_pool_dirty_percent
were intentially not added as tunable module parameters.
OpenZFS-issue: https://illumos.org/issues/9465
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/d6a4c3efCloses#7749
= Motivation
While dealing with another performance issue (see 126118f) we noticed
that we spend a lot of time in various places in the kernel when
constructing long nvlists. The problem is that when an nvlist is created
with the NV_UNIQUE_NAME set (which is the case most of the time), we do
a linear search through the whole list to ensure uniqueness for every
entry we add.
An example of the above scenario can be seen in the following
flamegraph, where more than have the time of the zfsdev_ioctl() is spent
on constructing nvlists. Flamegraph:
https://sdimitro.github.io/img/flame/sdimitro_snap_unmount3.svg
Adding a table to speed up lookups will help situations where we just
construct an nvlist (like the scenario above), in addition to regular
lookups and removals.
= What this patch does
In this diff we've implemented a hash-table on top of the nvlist code
that converts most nvlist operations from O(# number of entries) to
O(1)* (the start is for amortized time as the hash-table grows and
shrinks depending on the # of entries - plain lookup is strictly O(1)).
= Performance Analysis
To analyze the performance improvement I just used the setup from the
snapshot deletion issue mentioned above in the Motivation section.
Basically I created 10K filesystems with one snapshot each and then I
just used the API of libZFS_Core to pass down an nvlist of all the
snapshots to have them deleted. The reason I used my own driver program
was to have clean performance results of what actually happens in the
kernel. The flamegraphs and wall clock times mentioned below were
gathered from the start to the end of the driver program's run. Between
trials the testpool used was completely destroyed, the system was
rebooted and the testpool was completely recreated. The reason for this
dance was to get consistent results.
== Results (before patch):
=== Sampling Flamegraphs
[Trial 1] https://sdimitro.github.io/img/flame/DLPX-53417/trial-A.svg
[Trial 2] https://sdimitro.github.io/img/flame/DLPX-53417/trial-A2.svg
[Trial 3] https://sdimitro.github.io/img/flame/DLPX-53417/trial-A3.svg
=== Wall clock times (in seconds)
```
[Trial 4]
real 5.3
user 0.4
sys 2.3
[Trial 5]
real 8.2
user 0.4
sys 2.4
[Trial 6]
real 6.0
user 0.5
sys 2.3
```
== Results (after patch):
=== Sampling Flamegraphs
[Trial 1] https://sdimitro.github.io/img/flame/DLPX-53417/trial-Ae.svg
[Trial 2] https://sdimitro.github.io/img/flame/DLPX-53417/trial-A2e.svg
[Trial 3] https://sdimitro.github.io/img/flame/DLPX-53417/trial-A3e.svg
=== Wall clock times (in seconds)
```
[Trial 4]
real 4.9
user 0.0
sys 0.9
[Trial 5]
real 3.8
user 0.0
sys 0.9
[Trial 6]
real 3.6
user 0.0
sys 0.9
```
== Analysis
The results between the trials are consistent so in this sections I will
only talk about the flamegraph results from trial-1 and the wall-clock
results from trial-4.
From trial-1 we can see that zfs_dev_ioctl() goes from 2,331 to 996
samples counts. Specifically, the samples from fnvlist_add_nvlist() and
spa_history_log_nvl() are almost gone (~500 & ~800 to 5 & 5 samples),
leaving zfs_ioc_destroy_snaps() to dominate most samples from
zfs_dev_ioctl().
From trial-4 we see that the user time dropped to 0 secods. I believe
the consistent 0.4 seconds before my patch was applied was due to my
driver program constructing the long nvlist of snapshots so it can pass
it to the kernel. As for the system time, the effect there is more clear
(2.3 down to 0.9 seconds).
Porting Notes:
* DATA_TYPE_DONTCARE case added to switch in fm_nvprintr() and
zpool_do_events_nvprint().
Authored by: Serapheim Dimitropoulos <serapheim.dimitro@delphix.com>
Reviewed by: Matt Ahrens <matt@delphix.com>
Reviewed by: Sebastien Roy <sebastien.roy@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/9580
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/b5eca7b1Closes#7748
Follow up commit for OpenZFS 9438. See the OpenZFS-issue link below
for a complete analysis.
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://illumos.org/issues/9439
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/779220d
External-issue: DLPX-46861
Closes#7746
As reported by https://github.com/zfsonlinux/zfs/issues/4996, there is
yet another hole birth issue. In this one, if a block is entirely holes,
but the birth times are not all the same, we lose that information by
creating one hole with the current txg as its birth time.
The ZoL PR's fix approach is incorrect. Ultimately, the problem here is
that when you truncate and write a file in the same transaction group,
the dbuf for the indirect block will be zeroed out to deal with the
truncation, and then written for the write. During this process, we will
lose hole birth time information for any holes in the range. In the case
where a dnode is being freed, we need to determine whether the block
should be converted to a higher-level hole in the zio pipeline, and if
so do it when the dnode is being synced out.
Porting Notes:
* The DMU_OBJECT_END change in zfs_znode.c was already applied.
* Added test cases from #5675 provided by @rincebrain for hole_birth
issues. These test cases should be pushed upstream to OpenZFS.
* Updated mk_files which is used by several rsend tests so the
files created are a little more interesting and may contain holes.
Authored by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Matt Ahrens <matt@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/9438
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/738e2a3c
External-issue: DLPX-46861
Closes#7746
It's possible for an unrelated process, like blkid, to have the
volume open when 'zfs destroy' is run. Switch the cleanup function
to the destroy_dataset() helper which handles this case by retrying
the destroy when the dataset is busy.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7750
The RT rwsem implementation was changed to allow multiple readers
as of the 4.9.20-rt16 patch set. This results in a build failure
because the existing implementation was forced to directly access
the rwsem structure which has changed.
While this could be accommodated by adding additional compatibility
code. This patch resolves the build issue by simply assuming the
rwsem can never be upgraded. This functionality is a performance
optimization and all callers must already handle this case.
Converting the last remaining use of __SPIN_LOCK_UNLOCKED to
spin_lock_init() was additionally required to get a clean build.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7589
Systemd binaries necessary for mounting an encrypted root dataset
weren't copied to initramfs generated by dracut. This patch fixes
this and copies these binaries unconditionally, that is
regardless of whether native ZFS encryption is used for the
root dataset.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Diamantopoulos <georgediam@gmail.com>
Closes#7607Closes#7719
Porting notes:
* As of grub-2.02 these checksums are not supported. However, as
pointed out in #6501 there are alternatives such as EFISTUB which
work and have no such restriction. A warning was added to the
checksum property section of the zfs.8 man page.
Authored by: Toomas Soome <tsoome@me.com>
Reviewed by: C Fraire <cfraire@me.com>
Reviewed by: Robert Mustacchi <rm@joyent.com>
Reviewed by: Yuri Pankov <yuripv@yuripv.net>
Approved by: Dan McDonald <danmcd@joyent.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://illumos.org/issues/8906
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/7dec52fCloses#6501Closes#7714
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Serapheim Dimitropoulos <serapheim.dimitro@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Albert Lee <trisk@forkgnu.org>
Reviewed by: Igor Kozhukhov <igor@dilos.org>
Reviewed by: George Melikov <mail@gmelikov.ru>
Approved by: Dan McDonald <danmcd@joyent.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Updates to indirect blocks of spacemaps can contribute significantly to
write inflation. Therefore we want to reduce the indirect block size of
spacemaps from 128K to 16K.
Porting notes:
* Refactored to allow the dmu_object_alloc(), dmu_object_alloc_ibs()
and dmu_object_alloc_dnsize() functions to use a common shared
dmu_object_alloc_impl() function.
OpenZFS-issue: https://www.illumos.org/issues/9442
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/0c2e6408bCloses#7712
The reservation_008_pos test case has been observed to fail in
a non-dangerous way in approximately 5% of automated test runs.
Add the test case to the list of possible expected failures
until the test case can be made perfectly reliable.
Reviewed by: Giuseppe Di Natale <guss80@gmail.com>
Reviewed by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #7741Closes#7742
It is helpful to tune zfs_per_txg_dirty_frees_percent for commit
539d33c7(OpenZFS 6569 - large file delete can starve out write ops).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Richard Elling <Richard.Elling@RichardElling.com>
Signed-off-by: Feng Sun <loyou85@gmail.com>
Closes#7718
A memory leak occurs on lines 209 and 213 because the config is not
freed in the error case. The interface to add_config() seems less than
ideal - it would be better if it copied any data necessary from the
config and the caller freed it.
Porting notes:
* This issue had already been resolved on Linux by adding the missing
calls to nvlist_free(). But we'll adopt the upstream fix to keep
the behavior of the code consistent.
Authored by: Sara Hartse <sara.hartse@delphix.com>
Reviewed by: Matt Ahrens <matt@delphix.com>
Reviewed by: Serapheim Dimitropoulos <serapheim.dimitro@delphix.com>
Reviewed by: Giuseppe Di Natale <guss80@gmail.com>
Reviewed by: George Melikov <mail@gmelikov.ru>
Approved by: Robert Mustacchi <rm@joyent.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://illumos.org/issues/9457
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/be86bb8aCloses#7713
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Prashanth Sreenivasa <pks@delphix.com>
Reviewed by: Serapheim Dimitropoulos <serapheim.dimitro@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: Giuseppe Di Natale <guss80@gmail.com>
Reviewed by: George Melikov <mail@gmelikov.ru>
Approved by: Robert Mustacchi <rm@joyent.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
While investigating a different problem, I noticed that moved dnodes
(those processed by dnode_move_impl() via kmem_move()) have an incorrect
dn_next_type. This could cause the on-disk dn_type to be changed to an
invalid value. The fix to copy the dn_next_type in dnode_move_impl().
Porting notes:
* For the moment this potential issue cannot occur on Linux since
the SPL does not provide the kmem_move() functionality.
OpenZFS-issue: https://illumos.org/issues/9338
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/0717e6f13Closes#7715
The arc_hdr_realloc_crypt() function is responsible for converting
a "full" arc header to an extended "crypt" header and visa versa.
This code was originally written with a bcopy() so that any new
members added to arc headers would automatically be included
without requiring a code change. However, in practice this (along
with small differences in kmem_cache implementations between
various platforms) has caused a number of hard-to-find problems in
ports to other operating systems. This patch solves this problem
by making all member copies explicit and adding ASSERTs for fields
that cannot be set during the transfer. It also manually resets the
old header after the reallocation is finished so it can be properly
reallocated and reused.
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#7711
We were doing count_block() twice inside this function, once
unconditionally at the beginning (intended to catch the embedded block
case) and once near the end after processing the block.
The double-accounting caused the "zpool scrub" progress statistics in
"zpool status" to climb from 0% to 200% instead of 0% to 100%, and
showed double the I/O rate it was actually seeing.
This was apparently a regression introduced in commit 00c405b4b5,
which was an incorrect port of this OpenZFS commit:
https://github.com/openzfs/openzfs/commit/d8a447a7
Reviewed by: Thomas Caputi <tcaputi@datto.com>
Reviewed by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Steven Noonan <steven@uplinklabs.net>
Closes#7720Closes#7738
It's often necessary to understand why a change is made, before
understanding the exact changes that are made. Context provides
background, which by definition is necessary to understand prior to the
substance of the Pull Request.
Change the PR template to request "Motivation and Context" first, before
"Description".
Reviewed-by: Giuseppe Di Natale <guss80@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#7737
While the autoexpand property may seem like a small feature it
depends on a significant amount of system infrastructure. Enough
of that infrastructure is now in place that with a few modifications
for Linux it can be supported.
Auto-expand works as follows; when a block device is modified
(re-sized, closed after being open r/w, etc) a change uevent is
generated for udev. The ZED, which is monitoring udev events,
passes the change event along to zfs_deliver_dle() if the disk
or partition contains a zfs_member as identified by blkid.
From here the device is matched against all imported pool vdevs
using the vdev_guid which was read from the label by blkid. If
a match is found the ZED reopens the pool vdev. This re-opening
is important because it allows the vdev to be briefly closed so
the disk partition table can be re-read. Otherwise, it wouldn't
be possible to report the maximum possible expansion size.
Finally, if the property autoexpand=on a vdev expansion will be
attempted. After performing some sanity checks on the disk to
verify that it is safe to expand, the primary partition (-part1)
will be expanded and the partition table updated. The partition
is then re-opened (again) to detect the updated size which allows
the new capacity to be used.
In order to make all of the above possible the following changes
were required:
* Updated the zpool_expand_001_pos and zpool_expand_003_pos tests.
These tests now create a pool which is layered on a loopback,
scsi_debug, and file vdev. This allows for testing of non-
partitioned block device (loopback), a partition block device
(scsi_debug), and a file which does not receive udev change
events. This provided for better test coverage, and by removing
the layering on ZFS volumes there issues surrounding layering
one pool on another are avoided.
* zpool_find_vdev_by_physpath() updated to accept a vdev guid.
This allows for matching by guid rather than path which is a
more reliable way for the ZED to reference a vdev.
* Fixed zfs_zevent_wait() signal handling which could result
in the ZED spinning when a signal was not handled.
* Removed vdev_disk_rrpart() functionality which can be abandoned
in favor of kernel provided blkdev_reread_part() function.
* Added a rwlock which is held as a writer while a disk is being
reopened. This is important to prevent errors from occurring
for any configuration related IOs which bypass the SCL_ZIO lock.
The zpool_reopen_007_pos.ksh test case was added to verify IO
error are never observed when reopening. This is not expected
to impact IO performance.
Additional fixes which aren't critical but were discovered and
resolved in the course of developing this functionality.
* Added PHYS_PATH="/dev/zvol/dataset" to the vdev configuration for
ZFS volumes. This is as good as a unique physical path, while the
volumes are not used in the test cases anymore for other reasons
this improvement was included.
Reviewed by: Richard Elling <Richard.Elling@RichardElling.com>
Signed-off-by: Sara Hartse <sara.hartse@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#120Closes#2437Closes#5771Closes#7366Closes#7582Closes#7629
This project's goal is to make read-heavy channel programs and zfs(1m)
administrative commands faster by caching all the metadata that they will
need in the dbuf layer. This will prevent the data from being evicted, so
that any future call to i.e. zfs get all won't have to go to disk (very
much). There are two parts:
The dbuf_metadata_cache. We identify what to put into the cache based on
the object type of each dbuf. Caching objset properties os
{version,normalization,utf8only,casesensitivity} in the objset_t. The reason
these needed to be cached is that although they are queried frequently,
they aren't stored in a dbuf type which we can easily recognize and cache in
the dbuf layer; instead, we have to explicitly store them. There's already
existing infrastructure for maintaining cached properties in the objset
setup code, so I simply used that.
Performance Testing:
- Disabled kmem_flags
- Tuned dbuf_cache_max_bytes very low (128K)
- Tuned zfs_arc_max very low (64M)
Created test pool with 400 filesystems, and 100 snapshots per filesystem.
Later on in testing, added 600 more filesystems (with no snapshots) to make
sure scaling didn't look different between snapshots and filesystems.
Results:
| Test | Time (trunk / diff) | I/Os (trunk / diff) |
+------------------------+---------------------+---------------------+
| zpool import | 0:05 / 0:06 | 12.9k / 12.9k |
| zfs get all (uncached) | 1:36 / 0:53 | 16.7k / 5.7k |
| zfs get all (cached) | 1:36 / 0:51 | 16.0k / 6.0k |
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Thomas Caputi <tcaputi@datto.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Richard Lowe <richlowe@richlowe.net>
Ported-by: Alek Pinchuk <apinchuk@datto.com>
Signed-off-by: Alek Pinchuk <apinchuk@datto.com>
OpenZFS-issue: https://illumos.org/issues/9337
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/7dec52fCloses#7668
Commit 93b43af10 inadvertently introduced the following scenario which
can result in a deadlock. This issue was most easily reproduced by
LXD containers using a ZFS storage backend but should be reproducible
under any workload which is frequently mounting and unmounting.
-- THREAD A --
spa_sync()
spa_sync_upgrades()
rrw_enter(&dp->dp_config_rwlock, RW_WRITER, FTAG); <- Waiting on B
-- THREAD B --
mount_fs()
zpl_mount()
zpl_mount_impl()
dmu_objset_hold()
dmu_objset_hold_flags()
dsl_pool_hold()
dsl_pool_config_enter()
rrw_enter(&dp->dp_config_rwlock, RW_READER, tag);
sget()
sget_userns()
grab_super()
down_write(&s->s_umount); <- Waiting on C
-- THREAD C --
cleanup_mnt()
deactivate_super()
down_write(&s->s_umount);
deactivate_locked_super()
zpl_kill_sb()
kill_anon_super()
generic_shutdown_super()
sync_filesystem()
zpl_sync_fs()
zfs_sync()
zil_commit()
txg_wait_synced() <- Waiting on A
Reviewed by: Alek Pinchuk <apinchuk@datto.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7598Closes#7659Closes#7691Closes#7693
Update the SA_COPY_DATA macro to check if architecture supports
efficient unaligned memory accesses at compile time. Otherwise
fallback to using the sa_copy_data() function.
The kernel provided CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is
used to determine availability in kernel space. In user space
the x86_64, x86, powerpc, and sometimes arm architectures will
define the HAVE_EFFICIENT_UNALIGNED_ACCESS macro.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7642Closes#7684
Ztest failed with the following crash.
::status
debugging core file of ztest (64-bit) from clone-dc-slave-280-bc7947b1.dcenter
file: /usr/bin/amd64/ztest
initial argv: /usr/bin/amd64/ztest
threading model: raw lwps
status: process terminated by SIGABRT (Abort), pid=2150 uid=1025 code=-1
panic message: failure for thread 0xfffffd7fff112a40, thread-id 1: unprotected error in call to Lua API (Invalid
value type 'function' for key 'error')
::stack
libc.so.1`_lwp_kill+0xa()
libc.so.1`_assfail+0x182(fffffd7fffdfe8d0, 0, 0)
libc.so.1`assfail+0x19(fffffd7fffdfe8d0, 0, 0)
libzpool.so.1`vpanic+0x3d(fffffd7ffaa58c20, fffffd7fffdfeb00)
0xfffffd7ffaa28146()
0xfffffd7ffaa0a109()
libzpool.so.1`luaD_throw+0x86(3011a48, 2)
0xfffffd7ffa9350d3()
0xfffffd7ffa93e3f1()
libzpool.so.1`zcp_lua_to_nvlist+0x33(3011a48, 1, 2686470, fffffd7ffaa2e2c3)
libzpool.so.1`zcp_convert_return_values+0xa4(3011a48, 2686470, fffffd7ffaa2e2c3, fffffd7fffdfedd0)
libzpool.so.1`zcp_pool_error+0x59(fffffd7fffdfedd0, 1e0f450)
libzpool.so.1`zcp_eval+0x6f8(1e0f450, fffffd7ffaa483f8, 1, 0, 6400000, 1d33b30)
libzpool.so.1`dsl_destroy_snapshots_nvl+0x12c(2786b60, 0, 484750)
libzpool.so.1`dsl_destroy_snapshot+0x4f(fffffd7fffdfef70, 0)
ztest_dsl_dataset_cleanup+0xea(fffffd7fffdff4c0, 1)
ztest_dataset_destroy+0x53(1)
ztest_run+0x59f(fffffd7fff0e0498)
main+0x7ff(1, fffffd7fffdffa88)
_start+0x6c()
The problem is that zcp_convert_return_values() assumes that there's
exactly one value on the stack, but that isn't always true. It ends up
putting the wrong thing on the stack which is then consumed by
zcp_convert_return values, which either adds the wrong message to the
nvlist, or blows up.
The fix is to make sure that callers of zcp_convert_return_values()
clear the stack before pushing their error message, and
zcp_convert_return_values() should VERIFY that the stack is the expected
size.
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Sebastien Roy <sebastien.roy@delphix.com>
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Don Brady <don.brady@delphix.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Robert Mustacchi <rm@joyent.com>
OpenZFS-issue: https://www.illumos.org/issues/9424
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/eb7e57429Closes#7696
When running zdb without additional arguments against a pool containing
a checkpoint the entire checkpoint spacemap should not be dumped. Make
this behavior conditional upon passing the -mmmm option as described in
the zdb(8) man page.
-mmmm Display every spacemap record.
Reviewed-by: Serapheim Dimitropoulos <serapheim.dimitro@delphix.com>
Reviewed-by: Giuseppe Di Natale <guss80@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7702
When we do a scrub or resilver, ZFS counts the different types of blocks,
which can be printed by the ::zfs_blkstats mdb dcmd. However, it fails to
count embedded blocks.
Porting notes:
* Commit d4a72f23 moved count_blocks under a BP_IS_EMBEDDED conditional
as part of the sequential resilver functionality. Since phys_birth
would be zero that case should never happen as described above. This
is confirmed by the code coverage analysis. Remove the conditional
to realign that aspect of this function with OpenZFS.
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: George Melikov <mail@gmelikov.ru>
Reviewed by: Tom Caputi <tcaputi@datto.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Robert Mustacchi <rm@joyent.com>
OpenZFS-issue: https://www.illumos.org/issues/9454
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/d8a447a7Closes#7697
Problem
=======
Illumos bug 8373 was integrated, which now presents a code path where
"dmu_tx_assign" can fail. When "dmu_tx_assign" fails, it will not issue
the lwb that was passed in to "zil_lwb_write_issue". As a result, when
"zil_lwb_write_issue" returns, the lwb will still be in the "opened"
state, just as it was when "zil_lwb_write_issue" was originally called.
Solution
========
As a result of this new call path, the failed assertion needs to be
modified to be aware of this new possibility. Thus, we can only assert
that the lwb is no longer in the "opened" state if the returned lwb is
non-null, since we cannot differentiate between the case of
"dmu_tx_assign" failing or "zio_alloc_zil" failing within the call to
"zil_lwb_write_issue".
Authored by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: Matt Ahrens <matt@delphix.com>
Reviewed by: Serapheim Dimitropoulos <serapheim.dimitro@delphix.com>
Reviewed by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: George Melikov <mail@gmelikov.ru>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Matt Ahrens <mahrens@delphix.com>
OpenZFS-issue: https://www.illumos.org/issues/9456
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/a8b09f4eCloses#7695
Datasets that are deeply nested (~100 levels) are impractical. We just
put a limit of 50 levels to newly created datasets. Existing datasets
should work without a problem.
The problem can be seen by attempting to create a dataset using the -p
option with many levels:
panic[cpu0]/thread=ffffff01cd282c20: BAD TRAP: type=8 (#df Double fault) rp=ffffffff
fffffffffbc3aa60 unix:die+100 ()
fffffffffbc3ab70 unix:trap+157d ()
ffffff00083d7020 unix:_patch_xrstorq_rbx+196 ()
ffffff00083d7050 zfs:dbuf_rele+2e ()
...
ffffff00083d7080 zfs:dsl_dir_close+32 ()
ffffff00083d70b0 zfs:dsl_dir_evict+30 ()
ffffff00083d70d0 zfs:dbuf_evict_user+4a ()
ffffff00083d7100 zfs:dbuf_rele_and_unlock+87 ()
ffffff00083d7130 zfs:dbuf_rele+2e ()
... The block above repeats once per directory in the ...
... create -p command, working towards the root ...
ffffff00083db9f0 zfs:dsl_dataset_drop_ref+19 ()
ffffff00083dba20 zfs:dsl_dataset_rele+42 ()
ffffff00083dba70 zfs:dmu_objset_prefetch+e4 ()
ffffff00083dbaa0 zfs:findfunc+23 ()
ffffff00083dbb80 zfs:dmu_objset_find_spa+38c ()
ffffff00083dbbc0 zfs:dmu_objset_find+40 ()
ffffff00083dbc20 zfs:zfs_ioc_snapshot_list_next+4b ()
ffffff00083dbcc0 zfs:zfsdev_ioctl+347 ()
ffffff00083dbd00 genunix:cdev_ioctl+45 ()
ffffff00083dbd40 specfs:spec_ioctl+5a ()
ffffff00083dbdc0 genunix:fop_ioctl+7b ()
ffffff00083dbec0 genunix:ioctl+18e ()
ffffff00083dbf10 unix:brand_sys_sysenter+1c9 ()
Porting notes:
* Added zfs_max_dataset_nesting module option with documentation.
* Updated zfs_rename_014_neg.ksh for Linux.
* Increase the zfs.sh stack warning to 15K. Enough time has passed
that 16K can be reasonably assumed to be the default value. It
was increased in the 3.15 kernel released in June of 2014.
Authored by: Serapheim Dimitropoulos <serapheim.dimitro@delphix.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Reviewed by: Matt Ahrens <matt@delphix.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Garrett D'Amore <garrett@damore.org>
OpenZFS-issue: https://www.illumos.org/issues/9330
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/757a75aCloses#7681
Remove the dependency on partitionable devices for the clean_mirror
and scrub_mirror test cases. This allows for the setup and cleanup
of the test cases to be simplified by removing the need for complex
partitioning.
This change also resolves a issue where the clean_mirror devices
were not being properly damaged since the device name was not a
full path. The result being loopX files were being left in the
top level test_results directory.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7434Closes#7690
Add a default 4 KiB ashift for Amazon EC2 NVMe devices on instances with
NVMe ephemeral devices, such as the types c5d, f1, i3 and m5d.
As per the official documentation [1] a 4096 byte blocksize should be
used to match the underlying hardware.
The string was identified via:
$ sudo sginfo -M /dev/nvme0n1
INQUIRY response (cmd: 0x12)
----------------------------
Device Type 0
Vendor: NVMe
Product: Amazon EC2 NVMe
Revision level:
$ lsblk -io KNAME,TYPE,SIZE,MODEL
KNAME TYPE SIZE MODEL
nvme0n1 disk 442.4G Amazon EC2 NVMe Instance Storage
[1] https://docs.aws.amazon.com/AWSEC2/latest/UserGuide/
storage-optimized-instances.html
Retrived 2018-07-03
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <guss80@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Troels Nørgaard <tnn@tradeshift.com>
Closes#7676
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#7683
Motivation
==========
The current space map encoding has the following disadvantages:
[1] Assuming 512 sector size each entry can represent at most 16MB for a segment.
This makes the encoding very inefficient for large regions of space.
[2] As vdev-wide space maps have started to be used by new features (i.e.
device removal, zpool checkpoint) we've started imposing limits in the
vdevs that can be used with them based on the maximum addressable offset
(currently 64PB for a top-level vdev).
New encoding
============
The layout can be found at space_map.h and it remains backwards compatible with
the old one. The introduced two-word entry format, besides extending the limits
imposed by the single-entry layout, also includes a vdev field and some extra
padding after its prefix.
The extra padding after the prefix should is reserved for future usage (e.g.
new prefixes for future encodings or new fields for flags). The new vdev field
not only makes the space maps more self-descriptive, but also opens the doors
for pool-wide space maps (expected to be used in the log spacemap project).
One final important note is that the number of bits used for vdevs is reduced
to 24 bits for blkptrs. That was decided as we don't know of any setups that
use more than 16M vdevs for the time being and we wanted to fit the vdev field
in the space map. In addition that gives us some extra bits in dva_t.
Other references:
=================
The new encoding is also discussed towards the end of the Log Space Map
presentation from 2017's OpenZFS summit.
Link: https://www.youtube.com/watch?v=jj2IxRkl5bQ
Authored by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <gwilson@zfsmail.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Gordon Ross <gwr@nexenta.com>
Ported-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Tim Chase <tim@chase2k.com>
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/90a56e6d
OpenZFS-issue: https://www.illumos.org/issues/9238Closes#7665
This change introduces a new performance test which does random reads
and writes, but instead of using `bssplit` to determine the block size,
it uses a fixed blocksize. Additionally, some new IO sizes are added to
other tests and timestamp data is recorded with the performance data.
Authored by: Ahmed Gahnem <ahmedg@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Ported-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: John Wren Kennedy <john.kennedy@delphix.com>
Requires-builders: perf
OpenZFS-issue: https://www.illumos.org/issues/9184
OpenZFS-commit: https://github.com/openzfs/openzfs/pull/659
External-issue: DLPX-46724
Closes#7660
CID 176037: Uninitialized scalar variable
This patch fixes an uninitialized variable defect caught by
coverity and introduced in 69830602
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#7667
The enospc_002_pos test case would frequently fail due a command
succeeding when it was expected to fail due to lack of space.
In order to make this far less likely, files are created across
multiple transaction groups in order to consume as many unused
blocks as possible.
The dependency that the tests run on a partitioned block device
has been removed. It's simpler to use sparse files.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7663
Currently, there is a bug where older send streams without the
DMU_BACKUP_FEATURE_LARGE_DNODE flag are not handled correctly.
The code in receive_object() fails to handle cases where
drro->drr_dn_slots is set to 0, which is always the case when the
sending code does not support this feature flag. This patch fixes
the issue by ensuring that that a value of 0 is treated as
DNODE_MIN_SLOTS.
Tested-by: DHE <git@dehacked.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#7617Closes#7662
This patch fixes two problems with the encryption code. First, the
current code does not correctly prohibit the DMU from updating
dn_maxblkid during object truncation within a raw receive. This
usually only causes issues when the truncating DRR_FREE record is
aggregated with DRR_FREE records later in the receive, so it is
relatively hard to hit.
Second, this patch fixes a security issue where reading blocks
within an encrypted object did not guarantee that the dnode block
itself had ever been verified against its MAC. Usually the
verification happened anyway when the bonus buffer was read, but
some use cases (notably zvols) might never perform the check.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#7632
The formatting of the features beginning with large_blocks was broken
when the zpool_checkpoint feature was added.
Signed-off-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7658
Add checkpoint field in the default list of the zpool-list man page
Authored by: Eitan Adler <lists@eitanadler.com>
Reviewed by: Serapheim Dimitropoulos <serapheim.dimitro@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: kpande <github@tripleback.net>
Reviewed by: Tim Chase <tim@chase2k.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <guss80@gmail.com>
Approved by: Dan McDonald <danmcd@joyent.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://illumos.org/issues/9521
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/c5a860f7bCloses#7658
Details about the motivation of this feature and its usage can
be found in this blogpost:
https://sdimitro.github.io/post/zpool-checkpoint/
A lightning talk of this feature can be found here:
https://www.youtube.com/watch?v=fPQA8K40jAM
Implementation details can be found in big block comment of
spa_checkpoint.c
Side-changes that are relevant to this commit but not explained
elsewhere:
* renames members of "struct metaslab trees to be shorter without
losing meaning
* space_map_{alloc,truncate}() accept a block size as a
parameter. The reason is that in the current state all space
maps that we allocate through the DMU use a global tunable
(space_map_blksz) which defauls to 4KB. This is ok for metaslab
space maps in terms of bandwirdth since they are scattered all
over the disk. But for other space maps this default is probably
not what we want. Examples are device removal's vdev_obsolete_sm
or vdev_chedkpoint_sm from this review. Both of these have a
1:1 relationship with each vdev and could benefit from a bigger
block size.
Porting notes:
* The part of dsl_scan_sync() which handles async destroys has
been moved into the new dsl_process_async_destroys() function.
* Remove "VERIFY(!(flags & FWRITE))" in "kernel.c" so zhack can write
to block device backed pools.
* ZTS:
* Fix get_txg() in zpool_sync_001_pos due to "checkpoint_txg".
* Don't use large dd block sizes on /dev/urandom under Linux in
checkpoint_capacity.
* Adopt Delphix-OS's setting of 4 (spa_asize_inflation =
SPA_DVAS_PER_BP + 1) for the checkpoint_capacity test to speed
its attempts to fill the pool
* Create the base and nested pools with sync=disabled to speed up
the "setup" phase.
* Clear labels in test pool between checkpoint tests to avoid
duplicate pool issues.
* The import_rewind_device_replaced test has been marked as "known
to fail" for the reasons listed in its DISCLAIMER.
* New module parameters:
zfs_spa_discard_memory_limit,
zfs_remove_max_bytes_pause (not documented - debugging only)
vdev_max_ms_count (formerly metaslabs_per_vdev)
vdev_min_ms_count
Authored by: Serapheim Dimitropoulos <serapheim.dimitro@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Richard Lowe <richlowe@richlowe.net>
Ported-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Tim Chase <tim@chase2k.com>
OpenZFS-issue: https://illumos.org/issues/9166
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/7159fdb8Closes#7570
Otherwise the output is consumed by the output redirection.
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tim Chase <tim@chase2k.com>
Closes#7570
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <guss80@gmail.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: bunder2015 <omfgbunder@gmail.com>
Signed-off-by: ajs124 <git@ajs124.de>
Closes#7649
ms_shift can be incorrectly changed changed in MOS config for
indirect vdevs that have been historically expanded
According to spa_config_update() we expect new vdevs to have
vdev_ms_array equal to 0 and then we go ahead and set their metaslab
size. The problem is that indirect vdevs also have vdev_ms_array == 0
because their metaslabs are destroyed once their removal is done.
As a result, if a vdev was expanded and then removed may have its
ms_shift changed if another vdev was added after its removal.
Fortunately this behavior does not cause any type of crash or bad
behavior in the kernel but it can confuse zdb and anyone doing any kind
of analysis of the history of the pools.
Authored by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <gwilson@zfsmail.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Reviewed by: Prashanth Sreenivasa <pks@delphix.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tim Chase <tim@chase2k.com>
Ported-by: Tim Chase <tim@chase2k.com>
OpenZFS-commit: https://github.com/openzfs/openzfs/pull/651
OpenZFS-issue: https://illumos.org/issues/9591a
External-issue: DLPX-58879
Closes#7644
For zio taskq's which have multiple instances (e.g. z_rd_int_0,
z_rd_int_1, etc), each one has a unique name (the _0, _1, _2 suffix).
This makes performance analysis more difficult, because by default,
`perf` includes the thread name (which is the same as the taskq name) in
the stack trace. This means that we get 8 different stacks, all of
which are doing the same thing, but are executed from different taskq's.
We should remove the suffix of the taskq name, so that all the
read-interrupt threads are named z_rd_int.
Note that we already support multiple taskq's with the same name. This
happens when there are multiple pools. In this case the taskq has a
different tq_instance, which shows up in /proc/spl/taskq-all.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: Giuseppe Di Natale <guss80@gmail.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#7646
Adopt and extend the OpenZFS ZTS results analysis script for use
with ZFS on Linux. This allows for automatic analysis of tests
which may be skipped for a variety or reasons or which are not
entirely reliable.
In addition to the list of 'known' failures, which have been updated
for ZFS on Linux, there in a new 'maybe' section. This mapping
include tests which might be correctly skipped depending on the
test environment. This may be because of a missing dependency or
lack of required kernel support. This list also includes tests
which normally pass but might on occasion fail for a harmless
reason.
The script was also extended include a reason for why a given test
might be skipped or may fail. The reason will be included after
the test in the "results other than PASS that are expected" section.
For failures it is preferable to set the reason to the GitHub issue
number and for skipped tests several generic reasons are available.
You may also specify a custom reason if needed.
All tests were added back in to the linux.run file even if they are
expected to failed. There is value in running tests which may not
pass, the expected results for these tests has been encoded in
the new analysis script.
All tests which were disabled because they ran more slowly on a
32-bit system have been re-enabled. Developers working on 32-bit
systems should assess what it reasonable for their environment.
The unnecessary dependency on physical block devices was removed for
the checksum, grow_pool, and grow_replicas test groups so they are
no longer skipped. Updated the filetest_001_pos test case to run
properly now that it is enabled and moved the grow tests in to a
single directory.
Reviewed-by: Prakash Surya <prakash.surya@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7638
