The existing algorithm selects a preferred leaf vdev based on offset of the zio
request modulo the number of members in the mirror. It assumes the devices are
of equal performance and that spreading the requests randomly over both drives
will be sufficient to saturate them. In practice this results in the leaf vdevs
being under utilized.
The new algorithm takes into the following additional factors:
* Load of the vdevs (number outstanding I/O requests)
* The locality of last queued I/O vs the new I/O request.
Within the locality calculation additional knowledge about the underlying vdev
is considered such as; is the device backing the vdev a rotating media device.
This results in performance increases across the board as well as significant
increases for predominantly streaming loads and for configurations which don't
have evenly performing devices.
The following are results from a setup with 3 Way Mirror with 2 x HD's and
1 x SSD from a basic test running multiple parrallel dd's.
With pre-fetch disabled (vfs.zfs.prefetch_disable=1):
== Stripe Balanced (default) ==
Read 15360MB using bs: 1048576, readers: 3, took 161 seconds @ 95 MB/s
== Load Balanced (zfslinux) ==
Read 15360MB using bs: 1048576, readers: 3, took 297 seconds @ 51 MB/s
== Load Balanced (locality freebsd) ==
Read 15360MB using bs: 1048576, readers: 3, took 54 seconds @ 284 MB/s
With pre-fetch enabled (vfs.zfs.prefetch_disable=0):
== Stripe Balanced (default) ==
Read 15360MB using bs: 1048576, readers: 3, took 91 seconds @ 168 MB/s
== Load Balanced (zfslinux) ==
Read 15360MB using bs: 1048576, readers: 3, took 108 seconds @ 142 MB/s
== Load Balanced (locality freebsd) ==
Read 15360MB using bs: 1048576, readers: 3, took 48 seconds @ 320 MB/s
In addition to the performance changes the code was also restructured, with
the help of Justin Gibbs, to provide a more logical flow which also ensures
vdevs loads are only calculated from the set of valid candidates.
The following additional sysctls where added to allow the administrator
to tune the behaviour of the load algorithm:
* vfs.zfs.vdev.mirror.rotating_inc
* vfs.zfs.vdev.mirror.rotating_seek_inc
* vfs.zfs.vdev.mirror.rotating_seek_offset
* vfs.zfs.vdev.mirror.non_rotating_inc
* vfs.zfs.vdev.mirror.non_rotating_seek_inc
These changes where based on work started by the zfsonlinux developers:
https://github.com/zfsonlinux/zfs/pull/1487
Reviewed by: gibbs, mav, will
MFC after: 2 weeks
Sponsored by: Multiplay
References:
https://github.com/freebsd/freebsd@5c7a6f5dhttps://github.com/freebsd/freebsd@31b7f68dhttps://github.com/freebsd/freebsd@e186f564
Performance Testing:
https://github.com/zfsonlinux/zfs/pull/4334#issuecomment-189057141
Porting notes:
- The tunables were adjusted to have ZoL-style names.
- The code was modified to use ZoL's vd_nonrot.
- Fixes were done to make cstyle.pl happy
- Merge conflicts were handled manually
- freebsd/freebsd@e186f564bc by my
collegue Andriy Gapon has been included. It applied perfectly, but
added a cstyle regression.
- This replaces 556011dbec entirely.
- A typo "IO'a" has been corrected to say "IO's"
- Descriptions of new tunables were added to man/man5/zfs-module-parameters.5.
Ported-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4334
Commit d2f3e29 introduced the -p option which outputs full paths
for vdevs to multiple zpool subcommands. When this was merged
there was no conflict for this flag letter. However it's certain
there will be a conflict with the -p (parsable) flag used by other
subcommands. Therefore, -p is being changed to -P to avoid this.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4368
The following options have been added to the zpool add, iostat,
list, status, and split subcommands. The default behavior was
not modified, from zfs(8).
-g Display vdev GUIDs instead of the normal short
device names. These GUIDs can be used in-place of
device names for the zpool detach/off‐
line/remove/replace commands.
-L Display real paths for vdevs resolving all symbolic
links. This can be used to lookup the current block
device name regardless of the /dev/disk/ path used
to open it.
-p Display full paths for vdevs instead of only the
last component of the path. This can be used in
conjunction with the -L flag.
This behavior may also be enabled using the following environment
variables.
ZPOOL_VDEV_NAME_GUID
ZPOOL_VDEV_NAME_FOLLOW_LINKS
ZPOOL_VDEV_NAME_PATH
This change is based on worked originally started by Richard Yao
to add a -g option. Then extended by @ilovezfs to add a -L option
for openzfsonosx. Those changes have been merged, re-factored,
a -p option added and extended to all relevant zpool subcommands.
Original-patch-by: Richard Yao <ryao@gentoo.org>
Extended-by: ilovezfs <ilovezfs@icloud.com>
Extended-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: ilovezfs <ilovezfs@icloud.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2011Closes#4341
Debian based systems use nfs-kernel-server as the service name.
List both nfs-server.service and nfs-kernel-server.service so
this service will work on multiple distributions.
Signed-off-by: Grischa Zengel <github.zfsonlinux@zengel.info>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4350
Set a limit for the largest compressed block which can be written
to an L2ARC device. By default this limit is set to 16M so there
is no change in behavior.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Elling <Richard.Elling@RichardElling.com>
Signed-off-by: Tim Chase <tim@chase2k.com>
Closes#4323
Close the race window in zvol_open() to prevent removal of
zvol_state in the 'first open' code path. Move the call to
check_disk_change() under zvol_state_lock to make sure the
zvol_media_changed() and zvol_revalidate_disk() called by
check_disk_change() are invoked with positive zv_open_count.
Skip opened zvols when removing minors and set private_data
to NULL for zvols that are not in use whose minors are being
removed, to indicate to zvol_open() that the state is gone.
Skip opened zvols when renaming minors to avoid modifying
zv_name that might be in use, e.g. in zvol_ioctl().
Drop zvol_state_lock before calling add_disk() when creating
minors to avoid deadlocks with zvol_open().
Wrap dmu_objset_find() with spl_fstran_mark()/unmark().
Signed-off-by: Boris Protopopov <boris.protopopov@actifio.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <ryao@gentoo.org>
Closes#4344
The difference between `dmu_read_uio()` and `dmu_read_uio_dbuf()` is
that the former takes a hold while the latter uses an existing hold.
`zfs_read()` in the ZPL will use `dmu_read_uio_dbuf()` while
our analogous `zvol_write()` will use `dmu_write_uio_dbuf()`, but for no
apparent reason, we inherited a `zvol_read()` function from
OpenSolaris that does `dmu_read_uio()`. illumos-gate also still
uses `dmu_read_uio()` to this day. Lets switch to `dmu_read_uio_dbuf()`,
which is more performant.
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Chunwei Chen <tuxoko@gmail.com>
Closes#4316
In illumos-gate, `zvol_read` and `zvol_write` are both passed uio_t
rather than bio_t. Since we are translating from bio to uio for both, we
might as well unify the logic and have code more similar to its illumos
counterpart. At the same time, we can fix some regressions that occurred
versus the original code from illumos-gate.
We refactor zvol_write to take uio and also correct the
following problems:
1. We did `dnode_hold()` on each IO when we already had a hold.
2. We would attempt to send writes that exceeded `DMU_MAX_ACCESS` to the
DMU.
3. We could call `zil_commit()` twice. In this case, this is because
Linux uses the `->write` function to send flushes and can aggregate the
flush with a write. If a synchronous write occurred with the flush, we
effectively flushed twice when there is no need to do that.
zvol_read also suffers from the first two problems. Other platforms
suffer from the first, so we leave that for a second patch so that there
is a discrete patch for them to cherry-pick.
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Chunwei Chen <tuxoko@gmail.com>
Closes#4316
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <ryao@gentoo.org>
Closes#4251
When using large blocks like 1M, there will be more than UINT16_MAX qwords in
one block, so this ASSERT would go off. Also, it is possible for the histogram
to overflow. We cap them to UINT16_MAX to prevent this.
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4257
When extracting tokens from the string strtok(2) is allowed to modify
the passed buffer. Therefore the zfs_strcmp_pathname() function must
make a copy of the passed string before passing it to strtok(3).
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@intel.com>
Closes#4312
5809 Blowaway full receive in v1 pool causes kernel panic
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Alex Reece <alex@delphix.com>
Reviewed by: Will Andrews <will@freebsd.org>
Approved by: Gordon Ross <gwr@nexenta.com>
References:
https://www.illumos.org/issues/5809https://github.com/illumos/illumos-gate/commit/f40b29c
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
5767 fix several problems with zfs test suite
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Christopher Siden <christopher.siden@delphix.com>
Approved by: Gordon Ross <gwr@nexenta.com>
References:
https://www.illumos.org/issues/5767https://github.com/illumos/illumos-gate/commit/52244c0
Porting Notes:
- Only the updates to zpool_main.c were kept because the ZFS test
suite is not currently part of the ZoL source tree. The test
suite itself should be updated to include the latest versions
of the tests once we're running it for every commit
- Fixes `zpool list` output.
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Currently, only the 'b' flag takes an argument which is an offset into
the block at which a blkptr should be decoded. The index into the flag
string needed to be updated after parsing an argument.
Signed-off-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4304
6537 Panic on zpool scrub with DEBUG kernel
Reviewed by: Steve Gonczi <gonczi@comcast.net>
Reviewed by: Dan McDonald <danmcd@omniti.com>
Reviewed by: Igor Kozhukhov <ikozhukhov@gmail.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Approved by: Matthew Ahrens <mahrens@delphix.com>
References:
https://www.illumos.org/issues/6537https://github.com/illumos/illumos-gate/commit/8c04a1f
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
6096 ZFS_SMB_ACL_RENAME needs to cleanup better
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Gordon Ross <gordon.w.ross@gmail.com>
Reviewed by: George Wilson <gwilson@zfsmail.com>
Approved by: Robert Mustacchi <rm@joyent.com>
References:
https://www.illumos.org/issues/6096https://github.com/illumos/illumos-gate/commit/8f5190a5
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
6450 scrub/resilver unnecessarily traverses snapshots created
after the scrub started
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: Richard Elling <Richard.Elling@RichardElling.com>
Approved by: Richard Lowe <richlowe@richlowe.net>
References:
https://www.illumos.org/issues/6450https://github.com/illumos/illumos-gate/commit/38d6103
Ported-by: kernelOfTruth kerneloftruth@gmail.com
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
For a Case Insensitive file system we must avoid creating negative
entries in the dentry cache. We must also pass the FIGNORECASE into
zfs_lookup so that special files are handled correctly.
We must also prevent negative dentries from being created when files are
unlinked.
Tested by running fsstress from LTP (10 loops, 10 processes, 10,000 ops.)
Also tested with printks (now removed) to ensure that lookups come to
zpl_lookup when negative should not exist.
Tests:
1. ls Some-file.txt; touch some-file.txt; ls Some-file.txt
and ensure no errors.
2. touch Some-file.txt; rm some-file.txt; ls Some-file.txt
and ensure that the last ls shows log messages showing the lookup
went all the way to zpl_lookup.
Thanks to tuxoko for helping me get this correct.
Signed-off-by: Richard Sharpe <realrichardsharpe@gmail.com>
Signed-off-by: Chunwei Chen <tuxoko@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4243
6527 Possible access beyond end of string in zpool comment
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Dan McDonald <danmcd@omniti.com>
Approved by: Gordon Ross <gwr@nexenta.com>
References:
https://www.illumos.org/issues/6527https://github.com/illumos/illumos-gate/commit/2bd7a8d
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chunwei Chen <tuxoko@gmail.com>
6495 Fix mutex leak in dmu_objset_find_dp
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Approved by: Albert Lee <trisk@omniti.com>
References:
https://www.illumos.org/issues/6495https://github.com/illumos/illumos-gate/commit/2bad225
Ported-by: Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chunwei Chen <tuxoko@gmail.com>
6414 vdev_config_sync could be simpler
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
References:
https://www.illumos.org/issues/6414https://github.com/illumos/illumos-gate/commit/eb5bb58
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chunwei Chen <tuxoko@gmail.com>
Reintroduce a slightly adapted version of the Illumos logic for
synchronous unlinks. The basic idea here is that only files
smaller than zfs_delete_blocks (20480) blocks should be deleted
synchronously. Unlinking larger files should be handled
asynchronously to minimize impact to the caller.
To accomplish this iput() which is responsible for calling
zfs_znode_delete() on Linux is only called in the delete_now
path. Otherwise zfs_async_iput() is used which allows the
last reference to be dropped by a taskq thread effectively
making the removal asynchronous.
Porting notes:
- Add zfs_delete_blocks module option for performance analysis.
The default value is DMU_MAX_DELETEBLKCNT which is the same
as upstream. Reducing this value means that smaller files
will be unlinked asynchronously like large files.
- All occurrences of zfsvfs changes to zsb.
Ported-by: KernelOfTruth kerneloftruth@gmail.com
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
mount.zfs is called by convention (and util-linux) with arguments
last, i.e.
% mount.zfs <dataset> <mountpoint> -o <options>
This is not a problem on glibc since GNU getopt(3) will reorder the
arguments. However, alternative libc such as musl libc (or glibc with
$POSIXLY_CORRECT set) will not permute argv and fail to parse the -o
<options>. Use getopt_long so musl will permute arguments.
Signed-off-by: Christian Neukirchen <chneukirchen@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4222
Since it's set to arc_c_max / 2, it must be set after arc_c_max is set.
Also added protection against it falling below 2 * maxblocksize in
userland builds.
Signed-off-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4268
Adjusting arc_c directly is racy because it can happen in the context
of multiple threads. It should always be >= 2 * maxblocksize. Set it
to a known valid value rather than adjusting it directly.
In addition refactor arc_shrink() to a simpler structure, protect against
underflow in the calculation of the new arc_c value.
Signed-off-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reverts: 935434efCloses: #3904Closes: #4161
LLVM's static analyzer showed that we could subtract using an
uninitialized value on an error from vn_rdwr().
The correct behavior is to return -1 on an error, so lets do that
instead.
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4104
1778 Assertion failed: rn->rn_nozpool == B_FALSE
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <george@delphix.com>
Reviewed by: Richard Elling <richard.elling@richardelling.com>
Approved by: Gordon Ross <gordon.ross@nexenta.com>
References:
https://www.illumos.org/issues/1778https://github.com/illumos/illumos-gate/commit/bd0f709
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
5518 Memory leaks in libzfs import implementation
Reviewed by: Dan Fields <dan.fields@nexenta.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Serghei Samsi <sscdvp@gmail.com>
Approved by: Dan McDonald <danmcd@omniti.com>
References:
https://www.illumos.org/issues/5518https://github.com/illumos/illumos-gate/commit/078266a
Porting notes:
- One hunk of this change was already applied independently in
commit 4def05f.
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
6815179 zpool import with a large number of LUNs is too slow
6844191 zpool import, scanning of disks should be multi-threaded
References:
https://github.com/illumos/illumos-gate/commit/4f67d75
Porting notes:
- This change was originally never ported to Linux due to it
dependence on the thread pool interface. This patch solves
that issue by switching the code to use the existing taskq
implementation which provides the same basic functionality.
However, in order for this to work properly thread_init()
and thread_fini() must be called around to taskq consumer
to perform the needed thread initialization.
- The check_one_slice, nozpool_all_slices, and check_slices
functions have been disabled for Linux. They are difficult,
but possible, to implement for Linux due to how partitions
are get names. Since this is only an optimization this code
can be added at a latter date.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
4950 files sometimes can't be removed from a full filesystem
Reviewed by: Adam Leventhal <adam.leventhal@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Sebastien Roy <sebastien.roy@delphix.com>
Reviewed by: Boris Protopopov <bprotopopov@hotmail.com>
Approved by: Dan McDonald <danmcd@omniti.com>
References:
https://www.illumos.org/issues/4950https://github.com/illumos/illumos-gate/commit/4bb7380
Porting notes:
- ZoL currently does not log discards to zvols, so the portion of
this patch that modifies the discard logging to mark it as
freeing space has been discarded.
2. may_delete_now had been removed from zfs_remove() in ZoL.
It has been reintroduced.
3. We do not try to emulate vnodes, so the following lines are
not valid on Linux:
mutex_enter(&vp->v_lock);
may_delete_now = vp->v_count == 1 && !vn_has_cached_data(vp);
mutex_exit(&vp->v_lock);
This has been replaced with:
mutex_enter(&zp->z_lock);
may_delete_now = atomic_read(&ip->i_count) == 1 && !(zp->z_is_mapped);
mutex_exit(&zp->z_lock);
Ported-by: Richard Yao <richard.yao@clusterhq.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Correct the redhat specfile so that working debuginfo rpms are created
for the kernel modules. The generic specfile already does the right
thing.
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4224
Check if the lock is held while holding the z_hold_locks() lock.
This prevents a possible use-after-free bug for callers which are
not holding the lock. There currently are no such callers so this
can't cause a problem today but it has been fixed regardless.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chunwei Chen <tuxoko@gmail.com>
Closes#4244
Issue #4124
The pfn_t typedef was inherited from Illumos but never directly
used by any libspl consumers. This doesn't cause any issues in
user space but for consistency with the kernel build it has been
removed. See torvalds/linux/commit/34c0fd54.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Chunwei Chen <tuxoko@gmail.com>
Issue #4228
The registered xattr .list handler was simplified in the 4.5 kernel
to only perform a permission check. Given a dentry for the file it
must return a boolean indicating if the name is visible. This
differs slightly from the previous APIs which also required the
function to copy the name in to the provided list and return its
size. That is now all the responsibility of the caller.
This should be straight forward change to make to ZoL since we've
always required the caller to make the copy. However, this was
slightly complicated by the need to support 3 older APIs. Yes,
between 2.6.32 and 4.5 there are 4 versions of this interface!
Therefore, while the functional change in this patch is small it
includes significant cleanup to make the code understandable and
maintainable. These changes include:
- Improved configure checks for .list, .get, and .set interfaces.
- Interfaces checked from newest to oldest.
- Strict checking for each possible known interface.
- Configure fails when no known interface is available.
- HAVE_*_XATTR_LIST renamed HAVE_XATTR_LIST_* for consistency
with similar iops and fops configure checks.
- POSIX_ACL_XATTR_{DEFAULT|ACCESS} were removed forcing callers to
move to their replacements, XATTR_NAME_POSIX_ACL_{DEFAULT|ACCESS}.
Compatibility wrapper were added for old kernels.
- ZPL_XATTR_LIST_WRAPPER added which behaves the same as the existing
ZPL_XATTR_{GET|SET} WRAPPERs. Only the inode is guaranteed to be
a valid pointer, passing NULL for the 'list' and 'name' variables
is allowed and must be checked for. All .list functions were
updated to use the wrapper to aid readability.
- zpl_xattr_filldir() updated to use the .list function for its
permission check which is consistent with the updated Linux 4.5
interface. If a .list function is registered it should return 0
to indicate a name should be skipped, if there is no registered
function the name will be added.
- Additional documentation from xattr(7) describing the correct
behavior for each namespace was added before the relevant handlers.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Chunwei Chen <tuxoko@gmail.com>
Issue #4228
The follow_link() interface was retired in favor of get_link().
In the process of phasing in get_link() the Linux kernel went
through two different versions. The first of which depended
on put_link() and the final version on a delayed done function.
- Improved configure checks for .follow_link, .get_link, .put_link.
- Interfaces checked from newest to oldest.
- Strict checking for each possible known interface.
- Configure fails when no known interface is available.
- Both versions .get_link are detected and supported as well
two previous versions of .follow_link.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Chunwei Chen <tuxoko@gmail.com>
Issue #4228
5045 use atomic_{inc,dec}_* instead of atomic_add_*
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Garrett D'Amore <garrett@damore.org>
Approved by: Robert Mustacchi <rm@joyent.com>
References:
https://www.illumos.org/issues/5045https://github.com/illumos/illumos-gate/commit/1a5e258
Porting notes:
- All changes to non-ZFS files dropped.
- Changes to zfs_vfsops.c dropped because they were Illumos specific.
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4220
4953 zfs rename <snapshot> need not involve libshare
4954 "zfs create" need not involve libshare if we are not sharing
4955 libshare's get_zfs_dataset need not sort the datasets
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Sebastien Roy <sebastien.roy@delphix.com>
Reviewed by: Dan McDonald <danmcd@omniti.com>
Reviewed by: Gordon Ross <gordon.ross@nexenta.com>
Approved by: Garrett D'Amore <garrett@damore.org>
References:
https://www.illumos.org/issues/4953https://www.illumos.org/issues/4954https://www.illumos.org/issues/4955https://github.com/illumos/illumos-gate/commit/33cde0d
Porting notes:
- Dropped qsort libshare_zfs.c hunk, no equivalent ZoL code.
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4219
4039 zfs_rename()/zfs_link() needs stronger test for XDEV
Reviewed by: Gordon Ross <gordon.ross@nexenta.com>
Reviewed by: Kevin Crowe <kevin.crowe@nexenta.com>
Reviewed by: Saso Kiselkov <skiselkov.ml@gmail.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Approved by: Dan McDonald <danmcd@nexenta.com>
References:
https://www.illumos.org/issues/4039https://github.com/illumos/illumos-gate/commit/18e6497
Porting notes:
- This check was updated in Linux in a similar fashion early on in
the port. Therefore, this patch just reorders the function and
updates the comment so it flows the same way as the upstream code.
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4218
6298 zfs_create_008_neg and zpool_create_023_neg need to be updated
for large block support
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
References:
https://www.illumos.org/issues/6298https://github.com/illumos/illumos-gate/commit/e9316f7
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4217
3557 dumpvp_size is not updated correctly when a dump zvol's size is changed
3558 setting the volsize on a dump device does not return back ENOSPC
3559 setting a volsize larger than the space available sometimes succeeds
3560 dumpadm should be able to remove a dump device
Reviewed by: Adam Leventhal <ahl@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Christopher Siden <christopher.siden@delphix.com>
Approved by: Albert Lee <trisk@nexenta.com>
References:
https://www.illumos.org/issues/3559https://github.com/illumos/illumos-gate/commit/c61ea56
Porting notes:
- Internal zvol.c changes not applied due to implementation differences.
The external interface and behavior was already consistent with the
latest upstream code.
- Retired 2.6.28 HAVE_CHECK_DISK_SIZE_CHANGE configure check. All
supported kernels (2.6.32 and newer) provide this interface.
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4217
When replacing an xattr would cause overflowing in SA, we would fallback
to xattr dir. However, current implementation don't clear the one in SA,
so we would end up with duplicated SA.
For example, running the following script on an xattr=sa filesystem
would cause duplicated "user.1".
-- dup_xattr.sh begin --
randbase64()
{
dd if=/dev/urandom bs=1 count=$1 2>/dev/null | openssl enc -a -A
}
file=$1
touch $file
setfattr -h -n user.1 -v `randbase64 5000` $file
setfattr -h -n user.2 -v `randbase64 20000` $file
setfattr -h -n user.3 -v `randbase64 20000` $file
setfattr -h -n user.1 -v `randbase64 20000` $file
getfattr -m. -d $file
-- dup_xattr.sh end --
Also, when a filesystem is switch from xattr=sa to xattr=on, it will
never modify those in SA. This would cause strange behavior like, you
cannot delete an xattr, or setxattr would cause duplicate and the result
would not match when you getxattr.
For example, the following shell sequence.
-- shell begin --
$ sudo zfs set xattr=sa pp/fs0
$ touch zzz
$ setfattr -n user.test -v asdf zzz
$ sudo zfs set xattr=on pp/fs0
$ setfattr -x user.test zzz
setfattr: zzz: No such attribute
$ getfattr -d zzz
user.test="asdf"
$ setfattr -n user.test -v zxcv zzz
$ getfattr -d zzz
user.test="asdf"
user.test="asdf"
-- shell end --
We fix this behavior, by first finding where the xattr resides before
setxattr. Then, after we successfully updated the xattr in one location,
we will clear the other location. Note that, because update and clear
are not in single tx, we could still end up with duplicated xattr. But
by doing setxattr again, it can be fixed.
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Closes#3472Closes#4153
The fast write mutex is intended to protect accounting, but it is
redundant because all accounting is performed through atomic operations.
It also serializes all metaslab IO behind a mutex, which introduces a
theoretical scaling regression that the Illumos developers did not like
when we showed this to them. Removing it makes the selection of the
metaslab_group lock free as it is on Illumos. The selection is not quite
the same without the lock because the loop races with IO completions,
but any imbalances caused by this are likely to be corrected by
subsequent metaslab group selections.
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#3643
The zfs_znode_hold_enter() / zfs_znode_hold_exit() functions are used to
serialize access to a znode and its SA buffer while the object is being
created or destroyed. This kind of locking would normally reside in the
znode itself but in this case that's impossible because the znode and SA
buffer may not yet exist. Therefore the locking is handled externally
with an array of mutexs and AVLs trees which contain per-object locks.
In zfs_znode_hold_enter() a per-object lock is created as needed, inserted
in to the correct AVL tree and finally the per-object lock is held. In
zfs_znode_hold_exit() the process is reversed. The per-object lock is
released, removed from the AVL tree and destroyed if there are no waiters.
This scheme has two important properties:
1) No memory allocations are performed while holding one of the z_hold_locks.
This ensures evict(), which can be called from direct memory reclaim, will
never block waiting on a z_hold_locks which just happens to have hashed
to the same index.
2) All locks used to serialize access to an object are per-object and never
shared. This minimizes lock contention without creating a large number
of dedicated locks.
On the downside it does require znode_lock_t structures to be frequently
allocated and freed. However, because these are backed by a kmem cache
and very short lived this cost is minimal.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #4106
Add a zfs_object_mutex_size module option to facilitate resizing the
the per-dataset znode mutex array. Increasing this value may help
make the deadlock described in #4106 less common, but this is not a
proper fix. This patch is primarily to aid debugging and analysis.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tim Chase <tim@chase2k.com>
Issue #4106
