The current loop triggers a complaint that we are using an array offset
prior to a range check from cpp/offset-use-before-range-check when we
are actually calculating maximum and minimum values. I was about to file
a false positive report with CodeQL, but after looking at how the code
is structured, I really cannot blame CodeQL for mistaking this for a
range check.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14575
Traditionally ARC adaptation was limited to MRU/MFU distribution. But
for years people with metadata-centric workload demanded mechanisms to
also manage data/metadata distribution, that in original ZFS was just
a FIFO. As result ZFS effectively got separate states for data and
metadata, minimum and maximum metadata limits etc, but it all required
manual tuning, was not adaptive and in its heart remained a bad FIFO.
This change removes most of existing eviction logic, rewriting it from
scratch. This makes MRU/MFU adaptation individual for data and meta-
data, same as the distribution between data and metadata themselves.
Since most of required states separation was already done, it only
required to make arcs_size state field specific per data/metadata.
The adaptation logic is still based on previous concept of ghost hits,
just now it balances ARC capacity between 4 states: MRU data, MRU
metadata, MFU data and MFU metadata. To simplify arc_c changes instead
of arc_p measured in bytes, this code uses 3 variable arc_meta, arc_pd
and arc_pm, representing ARC balance between metadata and data, MRU and
MFU for data, and MRU and MFU for metadata respectively as 32-bit fixed
point fractions. Since we care about the math result only when need to
evict, this moves all the logic from arc_adapt() to arc_evict(), that
reduces per-block overhead, since per-block operations are limited to
stats collection, now moved from arc_adapt() to arc_access() and using
cheaper wmsums. This also allows to remove ugly ARC_HDR_DO_ADAPT flag
from many places.
This change also removes number of metadata specific tunables, part of
which were actually not functioning correctly, since not all metadata
are equal and some (like L2ARC headers) are not really evictable.
Instead it introduced single opaque knob zfs_arc_meta_balance, tuning
ARC's reaction on ghost hits, allowing administrator give more or less
preference to metadata without setting strict limits.
Some of old code parts like arc_evict_meta() are just removed, because
since introduction of ABD ARC they really make no sense: only headers
referenced by small number of buffers are not evictable, and they are
really not evictable no matter what this code do. Instead just call
arc_prune_async() if too much metadata appear not evictable.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14359
The intent is that this is like ENOTSUP, but specifically for when
something can't be done because we have no support for the requested
crypto parameters; eg unlocking a dataset or receiving a stream
encrypted with a suite we don't support.
Its not intended to be recoverable without upgrading ZFS itself.
If the request could be made to work by enabling a feature or modifying
some other configuration item, then some other code should be used.
load-key: In the future we might have more crypto suites (ie new values
for the `encryption` property. Right now trying to load a key on such
a future crypto suite will look up suite parameters off the end of the
crypto table, resulting in misbehaviour and/or crashes (or, with debug
enabled, trip the assertion in `zio_crypt_key_unwrap`).
Instead, lets check the value we got from the dataset, and if we can't
handle it, abort early.
recv: When receiving a raw stream encrypted with an unknown crypto
suite, `zfs recv` would report a generic `invalid backup stream`
(EINVAL). While technically correct, its not super helpful, so lets
ship a more specific error code and message.
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Rob Norris <robn@despairlabs.com>
Closes#14577
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#14585Closes#14592
The approach is straightforward: for dataset ops, if a key was offered,
find the encryption root and the various encryption parameters, derive a
wrapping key if necessary, and then unlock the encryption root. After
that all the regular dataset ops will return unencrypted data, and
that's kinda the whole thing.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Signed-off-by: Rob Norris <robn@despairlabs.com>
Closes#11551Closes#12707Closes#14503
The leading zeroes are part of the checksum so we should show them.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <robn@despairlabs.com>
Closes#14464
With the persistent error log feature we need to account for
spa_errlog_{scrub, last} containing mappings to other error log objects,
which need to be marked as in-use as well.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#14442Closes#14434
This reverts commit d30db519af. With
this change applied zloop.sh fails reliably with the following ASSERT.
zio_wait(zio_claim(NULL, zcb->zcb_spa, refcnt ? 0 : spa_min_claim_txg(
zcb->zcb_spa), bp, NULL, NULL, ZIO_FLAG_CANFAIL)) == 0 (0x2 == 0x0)
ASSERT at cmd/zdb/zdb.c:5452:zdb_count_block()
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#14306
CodeQL pointed out that for extreme floating point values, `sprintf()`
will overwrite a 32 character buffer. It cited 1e304 as an example,
which causes `sprintf()` to print 308 characters.
In practice, the numbers should never exceed 100, so this should not
happen. To silence the warning and also handle unexpected situations, we
change the code to use `snprintf()`.
This was missed during my audit of our use of `sprintf()`, since I did
not think to consider extreme floating point representations. It also
really should not happen, so this change is purely defensive
programming.
This was found by CodeQL's cpp/overrunning-write-with-float check.
Reviewed-by: Damian Szuberski <szuberskidamian@gmail.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14264
This was written by Jeff Bonick and was committed to OpenSolaris on
November 1, 2009. It appears that Jeff meant to continue the outer loop
iteration when `ddp->ddp_phys_birth == 0`, but put his check inside the
inner loop. This causes a pointer to uninitialized memory to be passed
to ddt_lookup() inside a VERIFY() statement whenever that condition is
true.
Reported-by: Coverity (CID 1524462)
Reviewed-by: Damian Szuberski <szuberskidamian@gmail.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14264
This is not in performance critical code, but static analyzers will
complain about it, so lets switch to pass by pointer here.
Reported-by: Coverity (CID-1524384)
Reviewed-by: Damian Szuberski <szuberskidamian@gmail.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14263
svb is declared on the stack. We then set parts of svb.svb_dva with
DVA_SET_VDEV(), DVA_SET_OFFSET() and DVA_SET_ASIZE(). However, the DVA
contains other fields for pad, GRID and G. When setting the fields we
use, we technically read uninitialized bits from the fields we do not
use. This makes Coverity and Clang's Static Analyzer complain.
Presumably, other static analyzers might complain too.
There is no real bug here, but we are still technically reading
undefined data and unless we stop doing that, static analyzers will
complain about it in perpetuum and this could obscure real issues. We
silence the static analyzer complaints by using a 0 struct initializer.
Reported by: Coverity (CID 1524627)
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14210
Assertions are meant to check assumptions, but the way that this
assertion is written does not check an assumption, since it is provably
always true. Removing the assertion will cause a compiler warning (made
into an error by -Werror) about printing up to 512 bytes to a 256-byte
buffer, so instead, we change the assertion to verify the assumption
that we never do a snprintf() that is truncated to avoid overrunning the
256-byte buffer.
This was caught by an audit of the codebase to look for misuse of
`snprintf()` after CodeQL reported that we had misused `snprintf()`. An
explanation of how snprintf() can be misused is here:
https://www.redhat.com/en/blog/trouble-snprintf
This particular instance did not misuse `snprintf()`, but it was caught
by the audit anyway.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14098
Clang's static analyzer complained that we dereference a NULL pointer in
dump_path() if we return 0 when there is an error.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14044
This patch inserts the `static` keyword to non-global variables,
which where found by the analysis tool smatch.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tino Reichardt <milky-zfs@mcmilk.de>
Closes#13970
In libzutil, for zpool_search_import and zpool_find_config, we use
libpc_handle_t internally, which does not maintain error code and it is
not exposed in the interface. Due to this, the error information is not
propagated to the caller. Instead, an error message is printed on
stderr.
This commit adds lpc_error field in libpc_handle_t and exposes it in
the interface, which can be used by the users of libzutil to get the
appropriate error information and handle it accordingly.
Users of the API can also control if they want to print the error
message on stderr.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Umer Saleem <usaleem@ixsystems.com>
Closes#13969
Coverity caught unsafe use of `strcpy()` in `ztest_dmu_objset_own()`,
`nfs_init_tmpfile()` and `dump_snapshot()`. It also caught an unsafe use
of `strlcat()` in `nfs_init_tmpfile()`.
Inspired by this, I did an audit of every single usage of `strcpy()` and
`strcat()` in the code. If I could not prove that the usage was safe, I
changed the code to use either `strlcpy()` or `strlcat()`, depending on
which function was originally used. In some cases, `snprintf()` was used
to replace multiple uses of `strcat` because it was cleaner.
Whenever I changed a function, I preferred to use `sizeof(dst)` when the
compiler is able to provide the string size via that. When it could not
because the string was passed by a caller, I checked the entire call
tree of the function to find out how big the buffer was and hard coded
it. Hardcoding is less than ideal, but it is safe unless someone shrinks
the buffer sizes being passed.
Additionally, Coverity reported three more string related issues:
* It caught a case where we do an overlapping memory copy in a call to
`snprintf()`. We fix that via `kmem_strdup()` and `kmem_strfree()`.
* It caught `sizeof (buf)` being used instead of `buflen` in
`zdb_nicenum()`'s call to `zfs_nicenum()`, which is passed to
`snprintf()`. We change that to pass `buflen`.
* It caught a theoretical unterminated string passed to `strcmp()`.
This one is likely a false positive, but we have the information
needed to do this more safely, so we change this to silence the false
positive not just in coverity, but potentially other static analysis
tools too. We switch to `strncmp()`.
* There was a false positive in tests/zfs-tests/cmd/dir_rd_update.c. We
suppress it by switching to `snprintf()` since other static analysis
tools might complain about it too. Interestingly, there is a possible
real bug there too, since it assumes that the passed directory path
ends with '/'. We add a '/' to fix that potential bug.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13913
In #13871, zfs_vdev_aggregation_limit_non_rotating and
zfs_vdev_aggregation_limit being signed was pointed out as a possible
reason not to eliminate an unnecessary MAX(unsigned, 0) since the
unsigned value was assigned from them.
There is no reason for these module parameters to be signed and upon
inspection, it was found that there are a number of other module
parameters that are signed, but should not be, so we make them unsigned.
Making them unsigned made it clear that some other variables in the code
should also be unsigned, so we also make those unsigned. This prevents
users from setting negative values that could potentially cause bad
behaviors. It also makes the code slightly easier to understand.
Mostly module parameters that deal with timeouts, limits, bitshifts and
percentages are made unsigned by this. Any that are boolean are left
signed, since whether booleans should be considered signed or unsigned
does not matter.
Making zfs_arc_lotsfree_percent unsigned caused a
`zfs_arc_lotsfree_percent >= 0` check to become redundant, so it was
removed. Removing the check was also necessary to prevent a compiler
error from -Werror=type-limits.
Several end of line comments had to be moved to their own lines because
replacing int with uint_t caused us to exceed the 80 character limit
enforced by cstyle.pl.
The following were kept signed because they are passed to
taskq_create(), which expects signed values and modifying the
OpenSolaris/Illumos DDI is out of scope of this patch:
* metaslab_load_pct
* zfs_sync_taskq_batch_pct
* zfs_zil_clean_taskq_nthr_pct
* zfs_zil_clean_taskq_minalloc
* zfs_zil_clean_taskq_maxalloc
* zfs_arc_prune_task_threads
Also, negative values in those parameters was found to be harmless.
The following were left signed because either negative values make
sense, or more analysis was needed to determine whether negative values
should be disallowed:
* zfs_metaslab_switch_threshold
* zfs_pd_bytes_max
* zfs_livelist_min_percent_shared
zfs_multihost_history was made static to be consistent with other
parameters.
A number of module parameters were marked as signed, but in reality
referenced unsigned variables. upgrade_errlog_limit is one of the
numerous examples. In the case of zfs_vdev_async_read_max_active, it was
already uint32_t, but zdb had an extern int declaration for it.
Interestingly, the documentation in zfs.4 was right for
upgrade_errlog_limit despite the module parameter being wrongly marked,
while the documentation for zfs_vdev_async_read_max_active (and friends)
was wrong. It was also wrong for zstd_abort_size, which was unsigned,
but was documented as signed.
Also, the documentation in zfs.4 incorrectly described the following
parameters as ulong when they were int:
* zfs_arc_meta_adjust_restarts
* zfs_override_estimate_recordsize
They are now uint_t as of this patch and thus the man page has been
updated to describe them as uint.
dbuf_state_index was left alone since it does nothing and perhaps should
be removed in another patch.
If any module parameters were missed, they were not found by `grep -r
'ZFS_MODULE_PARAM' | grep ', INT'`. I did find a few that grep missed,
but only because they were in files that had hits.
This patch intentionally did not attempt to address whether some of
these module parameters should be elevated to 64-bit parameters, because
the length of a long on 32-bit is 32-bit.
Lastly, it was pointed out during review that uint_t is a better match
for these variables than uint32_t because FreeBSD kernel parameter
definitions are designed for uint_t, whose bit width can change in
future memory models. As a result, we change the existing parameters
that are uint32_t to use uint_t.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Neal Gompa <ngompa@datto.com>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13875
Coverity caught these. With the exception of the file descriptor leak in
tests/zfs-tests/cmd/draid.c, they are all memory leaks.
Also, there is a piece of dead code in zfs_get_enclosure_sysfs_path().
We delete it as cleanup.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13921
Coverity complained about unchecked return values and unused values that
turned out to be unused return values.
Different approaches were used to handle the different cases of
unchecked return values:
* cmd/zdb/zdb.c: VERIFY0 was used in one place since the existing code
had no error handling. An error message was printed in another to
match the rest of the code.
* cmd/zed/agents/zfs_retire.c: We dismiss the return value with `(void)`
because the value is expected to be potentially unset.
* cmd/zpool_influxdb/zpool_influxdb.c: We dismiss the return value with
`(void)` because the values are expected to be potentially unset.
* cmd/ztest.c: VERIFY0 was used since we want failures if something goes
wrong in ztest.
* module/zfs/dsl_dir.c: We dismiss the return value with `(void)`
because there is no guarantee that the zap entry will always be there.
For example, old pools imported readonly would not have it and we do
not want to fail here because of that.
* module/zfs/zfs_fm.c: `fnvlist_add_*()` was used since the
allocations sleep and thus can never fail.
* module/zfs/zvol.c: We dismiss the return value with `(void)` because
we do not need it. This matches what is already done in the analogous
`zfs_replay_write2()`.
* tests/zfs-tests/cmd/draid.c: We suppress one return value with
`(void)` since the code handles errors already. The other return value
is handled by switching to `fnvlist_lookup_uint8_array()`.
* tests/zfs-tests/cmd/file/file_fadvise.c: We add error handling.
* tests/zfs-tests/cmd/mmap_sync.c: We add error handling for munmap, but
ignore failures on remove() with (void) since it is expected to be
able to fail.
* tests/zfs-tests/cmd/mmapwrite.c: We add error handling.
As for unused return values, they were all in places where there was
error handling, so logic was added to handle the return values.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13920
Coverity complains about this. It is not a bug as long as we never shift
by more than 31, but it is not terrible to change the constants from 1
to 1ULL as clean up.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13914
I see a few issues in the issue tracker that might be aided by being
able to turn this on. We have no module parameter for it, so I would
like to add one.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13874
Coverity found a file descriptor leak. Eyeballing it showed that we had
no handling for the `open()` call failing either. We can address both of
these at once.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Neal Gompa <ngompa@datto.com>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13862
Alloc zdb_cd_t since it is too large for the stack on windows
which results in `zdb` crashing immediately.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andrew Innes <andrew.c12@gmail.com>
Co-authored-by: Jorgen Lundman <lundman@lundman.net>
Closes#13807
The SA attribute containing the symlink target does not include a nul
terminator, so when printing the target zdb would sometimes include
garbage at the end of the string.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#13482
Even on Illumos it's only available in the 32-bit programming
environment, and, quoth enable_extended_FILE_stdio(3C):
> Historically, 32-bit Solaris applications have been limited to using
> only the file descriptors 0 through 255 with the standard I/O
> functions (see stdio(3C)) in the C library. The extended FILE
> facility allows well-behaved 32-bit applications to use any
> valid file descriptor with the standard I/O functions.
where "well-behaved" means that it
> does not directly access any fields in the FILE structure pointed
> to by the FILE pointer associated with any standard I/O stream,
And the stdio/flush.c implementation reads:
/*
* if this is not an internal extended FILE then check
* if _file is being changed from underneath us.
* It should not be because if
* it is then then we lose our ability to guard against
* silent data corruption.
*/
if (!iop->__xf_nocheck && bad_fd > -1 && iop->_magic != bad_fd) {
(void) fprintf(stderr,
"Application violated extended FILE safety mechanism.\n"
"Please read the man page for extendedFILE.\nAborting\n");
abort();
}
This appears to be an insane workaround for broken implementation with
exposed FILE internals and _file being an u8, both only on non-LP64;
it's shimmed out on all LP64 targets in Illumos,
and we shim it out as well: just get rid of it
This appears to've been originally fixed in illumos-gate
a5f69788de7ac07553de47f7fec8c05a9a94c105 ("PSARC 2006/162 Extended FILE
space for 32-bit Solaris processes", "1085341 32-bit stdio routines
should support file descriptors >255"), which also bears extendedFILE
and enable_extended_FILE_stdio(3C):
- unsigned char _file; /* UNIX System file descriptor */
+ unsigned char _magic; /* Old home of the file descriptor */
+ /* Only fileno(3C) can retrieve the
value now */
and
+/*
+ * Macros to aid the extended fd FILE work.
+ * This helps isolate the changes to only the 32-bit code
+ * since 64-bit Solaris is not affected by this.
+ */
+#ifdef _LP64
+#define GET_FD(iop) ((iop)->_file)
+#define SET_FILE(iop, fd) ((iop)->_file = (fd))
+#else
+#define GET_FD(iop) \
+ (((iop)->__extendedfd) ? _file_get(iop) : (iop)->_magic)
+#define SET_FILE(iop, fd) (iop)->_magic = (fd); (iop)->__extendedfd = 0
+#endif
Also remove the 1k setrlimit(NOFILE) calls: that's the default on Linux,
with 64k on Illumos and 171k on FreeBSD
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13411
bcopy() has a confusing argument order and is actually a move, not a
copy; they're all deprecated since POSIX.1-2001 and removed in -2008,
and we shim them out to mem*() on Linux anyway
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12996
Unfortunately macOS has obj-C keyword "fallthrough" in the OS headers.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Damian Szuberski <szuberskidamian@gmail.com>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Closes#13097
`configure` now accepts `--enable-asan` and `--enable-ubsan` switches
which results in passing `-fsanitize=address`
and `-fsanitize=undefined`, respectively, to the compiler. Those
flags are enabled in GitHub workflows for ZTS and zloop. Errors
reported by both instrumentations are corrected, except for:
- Memory leak reporting is (temporarily) suppressed. The cost of
fixing them is relatively high compared to the gains.
- Checksum computing functions in `module/zcommon/zfs_fletcher*`
have UBSan errors suppressed. It is completely impractical
to enforce 64-byte payload alignment there due to performance
impact.
- There's no ASan heap poisoning in `module/zstd/lib/zstd.c`. A custom
memory allocator is used there rendering that measure
unfeasible.
- Memory leaks detection has to be suppressed for `cmd/zvol_id`.
`zvol_id` is run by udev with the help of `ptrace(2)`. Tracing is
incompatible with memory leaks detection.
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: szubersk <szuberskidamian@gmail.com>
Closes#12928
zdb -d <pool>/<objset ID> does not work when
other command line arguments are included i.e.
zdb -U <cachefile> -d <pool>/<objset ID>
This change fixes the command line parsing
to handle this situation. Also fix issue
where zdb -r <dataset> <file> does not handle
the root <dataset> of the pool. Introduce -N
option to force <objset ID> to be interpreted
as a numeric objsetID.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Rich Ercolani <rincebrain@gmail.com>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Paul Zuchowski <pzuchowski@datto.com>
Closes#12845Closes#12944
This change introduces long options for zdb. It updates the usage
message as well to include the long options.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Manoj Joseph <manoj.joseph@delphix.com>
Closes#12818
Sometimes, we'd like to know info about the metaslab groups
on special vdevs too. So let's make -MM do something useful.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12750
In case if all label checksums will be invalid on any vdev, the pool
will become unimportable. From other side zdb with -l option will not
provide any useful information why it happened. Add notifications
about corrupted label checksums.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Fedor Uporov <fuporov.vstack@gmail.com>
Closes#2509Closes#12685
The only zdb utility require to read metaslab-related data during
read-only pool import because of spacemaps validation. Add global
variable which will allow zdb read spacemaps in case of readonly
import mode.
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Fedor Uporov <fuporov.vstack@gmail.com>
Closes#9095Closes#12687
The calculation of estimated time remaining in zdb -cc could overflow,
as reported in #10666. This patch fixes this, by using uint64_t instead
of ints in the calculations.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Teodor Spæren <teodor@sparen.no>
Closes#10666Closes#12610
As of the Linux 5.9 kernel a fallthrough macro has been added which
should be used to anotate all intentional fallthrough paths. Once
all of the kernel code paths have been updated to use fallthrough
the -Wimplicit-fallthrough option will because the default. To
avoid warnings in the OpenZFS code base when this happens apply
the fallthrough macro.
Additional reading: https://lwn.net/Articles/794944/
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12441
Unfortunately macOS reserves inode ID numbers 0-15, and we can
not used them. In macOS port we simply map them really high IDs.
Normally this is hidden inside the _os implementation, but this is
the one place in the common source files.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Closes#12530
It turns out that layouts of union bitfields are a pain, and the
current code results in an inconsistent layout between BE and LE
systems, leading to zstd-active datasets on one erroring out on
the other.
Switch everyone over to the LE layout, and add compatibility code
to read both.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12008Closes#12022
Update the logic to handle the dedup-case of consecutive
FREEs in the livelist code. The logic still ensures that
all the FREE entries are matched up with a respective
ALLOC by keeping a refcount for each FREE blkptr that we
encounter and ensuring that this refcount gets to zero
by the time we are done processing the livelist.
zdb -y no longer panics when encountering double frees
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Don Brady <don.brady@delphix.com>
Signed-off-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Closes#11480Closes#12177
Exporting names this short can easily cause nasty collisions with user code.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12050
