Commit torvalds/linux@2233f31aad
replaced ->readdir() with ->iterate() in struct file_operations.
All filesystems must now use the new ->iterate method.
To handle this the code was reworked to use the new ->iterate
interface. Care was taken to keep the majority of changes
confined to the ZPL layer which is already Linux specific.
However, minor changes were required to the common zfs_readdir()
function.
Compatibility with older kernels was accomplished by adding
versions of the trivial dir_emit* helper functions. Also the
various *_readdir() functions were reworked in to wrappers
which create a dir_context structure to pass to the new
*_iterate() functions.
Unfortunately, the new dir_emit* functions prevent us from
passing a private pointer to the filldir function. The xattr
directory code leveraged this ability through zfs_readdir()
to generate the list of xattr names. Since we can no longer
use zfs_readdir() a simplified zpl_xattr_readdir() function
was added to perform the same task.
Signed-off-by: Richard Yao <ryao@cs.stonybrook.edu>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1653
Issue #1591
When the property atime=on is set operations which only access
and inode do cause an atime update. However, it turns out that
dirty inodes with updated atimes are only written to disk when
the inodes get evicted from the cache. Somewhat surprisingly
the source suggests that this isn't a ZoL specific issue.
This behavior may in part explain why zfs's reclaim logic has
been observed to be slow. When reclaiming inodes its likely
that they have a dirty atime which will force a write to disk.
Obviously we don't want to force a write to disk for every
atime update, these needs to be batched. The right way to
do this is to fully implement the .dirty_inode and .write_inode
callbacks. However, to do that right requires proper unification
of some fields in the znode/inode. Then we could just mark the
inode dirty and leave it to the VFS to call .write_inode
periodically.
Until that work gets done we have to settle for some middle
ground. The simplest and safest thing we can do for now is
to write the dirty inode on last close. This should prevent
the majority of inodes in the cache from having dirty atimes
and not drastically increase the number of writes.
Some rudimentally testing to show how long it takes to drop
500,000 inodes from the cache shows promising results. This
is as expected because we're no longer do lots of IO as part
of the eviction, it was done earlier during the close.
w/out patch: ~30s to drop 500,000 inodes with drop_caches.
with patch: ~3s to drop 500,000 inodes with drop_caches.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
The approach taken was the rework zfs_holey() as little as
possible and then just wrap the code as needed to ensure
correct locking and error handling.
Tested with xfstests 285 and 286. All tests pass except for
7-9 of 285 which try to reserve blocks first via fallocate(2)
and fail because fallocate(2) is not yet supported.
Note that the filp->f_lock spinlock did not exist prior to
Linux 2.6.30, but we avoid the need for autotools check by
virtue of the fact that SEEK_DATA/SEEK_HOLE support was not
added until Linux 3.1.
An autoconf check was added for lseek_execute() which is
currently a private function but the expectation is that it
will be exported perhaps as early as Linux 3.11.
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1384
Until these hooks are fully implemented return the expected
-EOPNOTSUPP error to indicate they are not functional. This
allows test suites such as xfstests to cleanly skip testing
this functionality until it's implemented.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #229
The zpl_readdir() function shouldn't be registered as part of
the zpl_file_operations table, it must only be part of the
zpl_dir_file_operations table. By removing this callback
the VFS will now correctly return ENOTDIR when calling
getdents() on a file.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1404
The txg_sync(), zfs_putpage(), zvol_write(), and zvol_discard()
call paths must only use KM_PUSHPAGE to avoid potential deadlocks
during direct reclaim.
This patch annotates these call paths so any accidental use of
KM_SLEEP will be quickly detected. In the interest of stability
if debugging is disabled the offending allocation will have its
GFP flags automatically corrected. When debugging is enabled
any misuse will be treated as a fatal error.
This patch is entirely for debugging. We should be careful to
NOT become dependant on it fixing up the incorrect allocations.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
The commit, cfc9a5c88f, to fix deadlocks
in zpl_writepage() relied on PF_MEMALLOC. That had the effect of
disabling the direct reclaim path on all allocations originating from
calls to this function, but it failed to address the actual cause of
those deadlocks. This led to the same deadlocks being observed with
swap on zvols, but not with swap on the loop device, which exercises
this code.
The use of PF_MEMALLOC also had the side effect of permitting
allocations to be made from ZONE_DMA in instances that did not require
it. This contributes to the possibility of panics caused by depletion
of pages from ZONE_DMA.
As such, we revert this patch in favor of a proper fix for both issues.
Signed-off-by: Richard Yao <ryao@cs.stonybrook.edu>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #726
Currently only the (FALLOC_FL_PUNCH_HOLE) flag combination is
supported, since it's the only one that matches the behavior of
zfs_space(). This makes it pretty much useless in its current
form, but it's a start.
To support other flag combinations we would need to modify
zfs_space() to make it more flexible, or emulate the desired
functionality in zpl_fallocate().
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #334
The Linux 3.1 kernel updated the fops->fsync() callback yet again.
They now pass the requested range and delegate the responsibility
for calling filemap_write_and_wait_range() to the callback. In
addition imutex is no longer held by the caller and the callback
is responsible for taking the lock if required.
This commit updates the code to provide a zpl_fsync() function
for the updated API. Implementations for the previous two APIs
are also maintained for compatibility.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#445
Be careful not to unconditionally clear the PF_MEMALLOC bit in
the task structure. It may have already been set when entering
zpl_putpage() in which case it must remain set on exit. In
particular the kswapd thread will have PF_MEMALLOC set in
order to prevent it from entering direct reclaim. By clearing
it we allow the following NULL deref to potentially occur.
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<ffffffff8109c7ab>] balance_pgdat+0x25b/0x4ff
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #287
This warning was accidentally introduced by commit
f3ab88d646 which updated the
.readpages() implementation. The fix is to simply cast
the helper function to the appropriate type when passed.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Unlike the .readpage() callback which is passed a single locked page
to be populated. The .readpages() callback is passed a list of unlocked
pages which are all marked for read-ahead (PG_readahead set). It is
the responsibly of .readpages() to ensure to pages are properly locked
before being populated.
Prior to this change the requested read-ahead pages would be updated
outside of the page lock which is unsafe. The unlocked pages would then
be unlocked again which is harmless but should have been immediately
detected as bug. Unfortunately, newer kernels failed detect this issue
because the check is done with a VM_BUG_ON which is disabled by default.
Luckily, the old Debian Lenny 2.6.26 kernel caught this because it
simply uses a BUG_ON.
The straight forward fix for this is to update the .readpages() callback
to use the read_cache_pages() helper function. The helper function will
ensure that each page in the list is properly locked before it is passed
to the .readpage() callback. In addition resolving the bug, this results
in a nice simplification of the existing code.
The downside to this change is that instead of passing one large read
request to the dmu multiple smaller ones are submitted. All of these
requests however are marked for readahead so the lower layers should
issue a large I/O regardless. Thus most of the request should hit the
ARC cache.
Futher optimization of this code can be done in the future is a perform
analysis determines it to be worthwhile. But for the moment, it is
preferable that code be correct and understandable.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#355
While the existing implementation of .writepage()/zpl_putpage() was
functional it was not entirely correct. In particular, it would move
dirty pages in to a clean state simply after copying them in to the
ARC cache. This would result in the pages being lost if the system
were to crash enough though the Linux VFS believed them to be safe on
stable storage.
Since at the moment virtually all I/O, except mmap(2), bypasses the
page cache this isn't as bad as it sounds. However, as hopefully
start using the page cache more getting this right becomes more
important so it's good to improve this now.
This patch takes a big step in that direction by updating the code
to correctly move dirty pages through a writeback phase before they
are marked clean. When a dirty page is copied in to the ARC it will
now be set in writeback and a completion callback is registered with
the transaction. The page will stay in writeback until the dmu runs
the completion callback indicating the page is on stable storage.
At this point the page can be safely marked clean.
This process is normally entirely asynchronous and will be repeated
for every dirty page. This may initially sound inefficient but most
of these pages will end up in a few txgs. That means when they are
eventually written to disk they should be nicely batched. However,
there is room for improvement. It may still be desirable to batch
up the pages in to larger writes for the dmu. This would reduce
the number of callbacks and small 4k buffer required by the ARC.
Finally, if the caller requires that the I/O be done synchronously
by setting WB_SYNC_ALL or if ZFS_SYNC_ALWAYS is set. Then the I/O
will trigger a zil_commit() to flush the data to stable storage.
At which point the registered callbacks will be run leaving the
date safe of disk and marked clean before returning from .writepage.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Disable the normal reclaim path for zpl_putpage(). This ensures that
all memory allocations under this call path will never enter direct
reclaim. If this were to happen the VM might try to write out
additional pages by calling zpl_putpage() again resulting in a
deadlock.
This sitution is typically handled in Linux by marking each offending
allocation GFP_NOFS. However, since much of the code used is common
it makes more sense to use PF_MEMALLOC to flag the entire call tree.
Alternately, the code could be updated to pass the needed allocation
flags but that's a more invasive change.
The following example of the above described deadlock was triggered
by test 074 in the xfstest suite.
Call Trace:
[<ffffffff814dcdb2>] down_write+0x32/0x40
[<ffffffffa05af6e4>] dnode_new_blkid+0x94/0x2d0 [zfs]
[<ffffffffa0597d66>] dbuf_dirty+0x556/0x750 [zfs]
[<ffffffffa05987d1>] dmu_buf_will_dirty+0x81/0xd0 [zfs]
[<ffffffffa059ee70>] dmu_write+0x90/0x170 [zfs]
[<ffffffffa0611afe>] zfs_putpage+0x2ce/0x360 [zfs]
[<ffffffffa062875e>] zpl_putpage+0x1e/0x60 [zfs]
[<ffffffffa06287b2>] zpl_writepage+0x12/0x20 [zfs]
[<ffffffff8115f907>] writeout+0xa7/0xd0
[<ffffffff8115fa6b>] move_to_new_page+0x13b/0x170
[<ffffffff8115fed4>] migrate_pages+0x434/0x4c0
[<ffffffff811559ab>] compact_zone+0x4fb/0x780
[<ffffffff81155ed1>] compact_zone_order+0xa1/0xe0
[<ffffffff8115602c>] try_to_compact_pages+0x11c/0x190
[<ffffffff811200bb>] __alloc_pages_nodemask+0x5eb/0x8b0
[<ffffffff8115464a>] alloc_pages_current+0xaa/0x110
[<ffffffff8111e36e>] __get_free_pages+0xe/0x50
[<ffffffffa03f0e2f>] kv_alloc+0x3f/0xb0 [spl]
[<ffffffffa03f11d9>] spl_kmem_cache_alloc+0x339/0x660 [spl]
[<ffffffffa05950b3>] dbuf_create+0x43/0x370 [zfs]
[<ffffffffa0596fb1>] __dbuf_hold_impl+0x241/0x480 [zfs]
[<ffffffffa0597276>] dbuf_hold_impl+0x86/0xc0 [zfs]
[<ffffffffa05977ff>] dbuf_hold_level+0x1f/0x30 [zfs]
[<ffffffffa05a9dde>] dmu_tx_check_ioerr+0x4e/0x110 [zfs]
[<ffffffffa05aa1f9>] dmu_tx_count_write+0x359/0x6f0 [zfs]
[<ffffffffa05aa5df>] dmu_tx_hold_write+0x4f/0x70 [zfs]
[<ffffffffa0611a6d>] zfs_putpage+0x23d/0x360 [zfs]
[<ffffffffa062875e>] zpl_putpage+0x1e/0x60 [zfs]
[<ffffffff811221f9>] write_cache_pages+0x1c9/0x4a0
[<ffffffffa0628738>] zpl_writepages+0x18/0x20 [zfs]
[<ffffffff81122521>] do_writepages+0x21/0x40
[<ffffffff8119bbbd>] writeback_single_inode+0xdd/0x2c0
[<ffffffff8119bfbe>] writeback_sb_inodes+0xce/0x180
[<ffffffff8119c11b>] writeback_inodes_wb+0xab/0x1b0
[<ffffffff8119c4bb>] wb_writeback+0x29b/0x3f0
[<ffffffff8119c6cb>] wb_do_writeback+0xbb/0x240
[<ffffffff811308ea>] bdi_forker_task+0x6a/0x310
[<ffffffff8108ddf6>] kthread+0x96/0xa0
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#327
Under Linux the VFS handles virtually all of the mmap() access
checks. Filesystem specific checks are left to be handled in
the .mmap() hook and normally there arn't any.
However, ZFS provides a few attributes which can influence the
mmap behavior and should be honored. Note, currently the code
to modify these attributes has not been implemented under Linux.
* ZFS_IMMUTABLE | ZFS_READONLY | ZFS_APPENDONLY: when any of these
attributes are set a file may not be mmaped with write access.
* ZFS_AV_QUARANTINED: when set a file file may not be mmaped with
read or exec access.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Enable zfs_getpage, zfs_fillpage, zfs_putpage, zfs_putapage functions.
The functions have been modified to make them Linux friendly.
ZFS uses these functions to read/write the mmapped pages. Using them
from readpage/writepage results in clear code. The patch also adds
readpages and writepages interface functions to read/write list of
pages in one function call.
The code change handles the first mmap optimization mentioned on
https://github.com/behlendorf/zfs/issues/225
Signed-off-by: Prasad Joshi <pjoshi@stec-inc.com>
Signed-off-by: Brian Behlendorf <behlendorf@llnl.gov>
Issue #255
How nfsd handles .fsync() has been changed a couple of times in the
recent kernels. But basically there are three cases we need to
consider.
Linux 2.6.12 - 2.6.33
* The .fsync() hook takes 3 arguments
* The nfsd will call .fsync() with a NULL file struct pointer.
Linux 2.6.34
* The .fsync() hook takes 3 arguments
* The nfsd no longer calls .fsync() but instead used sync_inode()
Linux 2.6.35 - 2.6.x
* The .fsync() hook takes 2 arguments
* The nfsd no longer calls .fsync() but instead used sync_inode()
For once it looks like we've gotten lucky. The first two cases can
actually be collased in to one if we stop using the file struct
pointer entirely. Since the dentry is still passed in both cases
this is possible. The last case can then be safely handled by
unconditionally using the dentry in the file struct pointer now
that we know the nfsd caller has been removed.
Closes#230
As of Linux 2.6.29 a clean credential API was added to the Linux kernel.
Previously the credential was embedded in the task_struct. Because the
SPL already has considerable support for handling this API change the
ZPL code has been updated to use the Solaris credential API.
In the original implementation the zfs_open()/zfs_close() hooks
were dropped for simplicity. This was functional but not 100%
correct with the expected ZFS sematics. Updating and re-adding the
zfs_open()/zfs_close() hooks resolves the following issues.
1) The ZFS_APPENDONLY file attribute is once again honored. While
there are still no Linux tools to set/clear these attributes once
there are it should behave correctly.
2) Minimal virus scan file attribute hooks were added. Once again
this support in disabled but the infrastructure is back in place.
3) Most importantly correctly handle assigning files which were
opened syncronously to the intent log. Without this change O_SYNC
modifications could be lost during a system crash even though they
were marked synchronous.
The fsync() callback in the file_operations structure used to take
3 arguments. The callback now only takes 2 arguments because the
dentry argument was determined to be unused by all consumers. To
handle this a compatibility prototype was added to ensure the right
prototype is used. Our implementation never used the dentry argument
either so it's just a matter of using the right prototype.
It's worth taking a moment to describe how mmap is implemented
for zfs because it differs considerably from other Linux filesystems.
However, this issue is handled the same way under OpenSolaris.
The issue is that by design zfs bypasses the Linux page cache and
leaves all caching up to the ARC. This has been shown to work
well for the common read(2)/write(2) case. However, mmap(2)
is problem because it relies on being tightly integrated with the
page cache. To handle this we cache mmap'ed files twice, once in
the ARC and a second time in the page cache. The code is careful
to keep both copies synchronized.
When a file with an mmap'ed region is written to using write(2)
both the data in the ARC and existing pages in the page cache
are updated. For a read(2) data will be read first from the page
cache then the ARC if needed. Neither a write(2) or read(2) will
will ever result in new pages being added to the page cache.
New pages are added to the page cache only via .readpage() which
is called when the vfs needs to read a page off disk to back the
virtual memory region. These pages may be modified without
notifying the ARC and will be written out periodically via
.writepage(). This will occur due to either a sync or the usual
page aging behavior. Note because a read(2) of a mmap'ed file
will always check the page cache first even when the ARC is out
of date correct data will still be returned.
While this implementation ensures correct behavior it does have
have some drawbacks. The most obvious of which is that it
increases the required memory footprint when access mmap'ed
files. It also adds additional complexity to the code keeping
both caches synchronized.
Longer term it may be possible to cleanly resolve this wart by
mapping page cache pages directly on to the ARC buffers. The
Linux address space operations are flexible enough to allow
selection of which pages back a particular index. The trick
would be working out the details of which subsystem is in
charge, the ARC, the page cache, or both. It may also prove
helpful to move the ARC buffers to a scatter-gather lists
rather than a vmalloc'ed region.
Additionally, zfs_write/read_common() were used in the readpage
and writepage hooks because it was fairly easy. However, it
would be better to update zfs_fillpage and zfs_putapage to be
Linux friendly and use them instead.
The Linux specific file operations have all been located in the
file zpl_file.c. These functions primarily rely on the reworked
zfs_* functions to do their job. They are also responsible for
converting the possible Solaris style error codes to negative
Linux errors.
This first zpl_* commit also includes a common zpl.h header with
minimal entries to register the Linux specific hooks. In also
adds all the new zpl_* file to the Makefile.in. This is not a
standalone commit, you required the following zpl_* commits.
