Authored by: Toomas Soome <tsoome@me.com>
Reviewed by: Yuri Pankov <yuripv@yuripv.net>
Reviewed by: Andy Fiddaman <omnios@citrus-it.co.uk>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Approved by: Dan McDonald <danmcd@joyent.com>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/9035
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/46ac8fdfc5Closes#7206
Currently, raw zfs sends transfer the encrypted master keys and
objset_phys_t encryption parameters in the DRR_BEGIN payload of
each send file. Both of these are processed as soon as they are
read in dmu_recv_stream(), meaning that the new keys are set
before the new snapshot is received. In addition to the fact that
this changes the user's keys for the dataset earlier than they
might expect, the keys were never reset to what they originally
were in the event that the receive failed. This patch splits the
processing into objset handling and key handling, the later of
which is moved to dmu_recv_end() so that they key change can be
done atomically.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#7200
The current design of ZFS encryption only allows a dataset to
have one DSL Crypto Key at a time. As a result, it is important
that the zfs receive code ensures that only one key can be in use
at a time for a given DSL Directory. zfs receive -F complicates
this, since the new dataset is received as a clone of the existing
one so that an atomic switch can be done at the end. To prevent
confusion about which dataset is actually encrypted a check was
added to ensure that encrypted datasets cannot use zfs recv -F to
completely replace existing datasets. Unfortunately, the check did
not take into account unencrypted datasets being overriden by
encrypted ones as a case.
Along the same lines, the code also failed to ensure that raw
recieves could not be done on top of existing unencrypted
datasets, which causes amny problems since the new stream cannot
be decrypted.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#7199
Currently, the DMU relies on ZIO layer compression to free LO
dnode blocks that no longer have objects in them. However,
raw receives disable all compression, meaning that these blocks
can never be freed. In addition to the obvious space concerns,
this could also cause incremental raw receives to fail to mount
since the MAC of a hole is different from that of a completely
zeroed block.
This patch corrects this issue by adding a special case in
zio_write_compress() which will attempt to compress these blocks
to a hole even if ZIO_FLAG_RAW_ENCRYPT is set. This patch also
removes the zfs_mdcomp_disable tunable, since tuning it could
cause these same issues.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#7198
1b66810b introduced serveral changes which improved the reliability
of zfs sends when large dnodes were involved. However, these fixes
required adding a few calls to txg_wait_synced() in the DRR_OBJECT
handling code. Although most of them are currently necessary, this
patch allows the code to continue without waiting in some cases
where it doesn't have to.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#7197
This one line patch adds adds a set to os->os_next_write_raw
that was omitted when the code was updated in 1b66810. Without
it, the code (in some instances) could attempt to write raw
encrypted data as regular unencrypted data without the keys
being loaded, triggering an ASSERT in zio_encrypt().
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#7196
Currently, ZIL claiming dirties objsets which causes
dsl_pool_sync() to attempt to perform user accounting on
them. This causes problems for encrypted datasets that were
raw received before the system went offline since they
cannot perform user accounting until they have their keys
loaded. This triggers an ASSERT in zio_encrypt(). Since
encryption was added, the code now depends on the fact that
data should only be written when objsets are owned. This
patch adds a check in dmu_objset_do_userquota_updates()
to ensure that useraccounting is only done when the objsets
are actually owned for write. As part of this work, the
zfsvfs and zvol code was updated so that it no longer lies
about owning objsets readonly.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#6916Closes#7163
CID 173243, 173245: Memory - corruptions (OVERRUN)
Added size argument to lcompat_sprintf() to avoid use of INT_MAX
CID 173244: Integer handling issues (OVERFLOW_BEFORE_WIDEN)
Added cast to uint64_t to avoid a 32 bit overflow warning
CID 173242: Integer handling issues (CONSTANT_EXPRESSION_RESULT)
Conditionally removed unused luai_numisnan() floating point check
CID 173241: Resource leaks (RESOURCE_LEAK)
Added missing close(fd) on error path
CID 173240: (UNINIT)
Fixed uninitialized variable in get_special_prop()
CID 147560: Null pointer dereferences (NULL_RETURNS)
Cleaned up bad code merge in dsl_dataset_promote_check()
CID 28475: Memory - illegal accesses (OVERRUN)
Fixed lcompat_sprintf() to use a size paramater
CID 28418, 28422: Error handling issues (CHECKED_RETURN)
Added function result cast to (void) to avoid warning
CID 23935, 28411, 28412: Memory - corruptions (ARRAY_VS_SINGLETON)
Added casts to avoid exposing result as an array
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@delphix.com>
Closes#7181
This patch corrects a small security issue with 9c5167d1. When the
project dnode was added to the objset_phys_t, it was not included
in the local MAC for cryptographic protection, allowing an attacker
to modify this data without the consent of the key holder. This
patch does represent an on-disk format change for anyone using
project dnodes on an encrypted dataset.
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7177
The use of void __attribute__((noreturn)) in kernel builds
was causing lots of warnings if CONFIG_STACK_VALIDATION
is active. For now we just remove this attribute to achieve
clean builds for the Lua module. There was no significant
increase in the time to run the full channel_program ZTS tests.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Don Brady <don.brady@delphix.com>
Closes#7173
PROBLEM
=======
It's possible for a parent zio to complete even though it has children
which have not completed. This can result in the following panic:
> $C
ffffff01809128c0 vpanic()
ffffff01809128e0 mutex_panic+0x58(fffffffffb94c904, ffffff597dde7f80)
ffffff0180912950 mutex_vector_enter+0x347(ffffff597dde7f80)
ffffff01809129b0 zio_remove_child+0x50(ffffff597dde7c58, ffffff32bd901ac0,
ffffff3373370908)
ffffff0180912a40 zio_done+0x390(ffffff32bd901ac0)
ffffff0180912a70 zio_execute+0x78(ffffff32bd901ac0)
ffffff0180912b30 taskq_thread+0x2d0(ffffff33bae44140)
ffffff0180912b40 thread_start+8()
> ::status
debugging crash dump vmcore.2 (64-bit) from batfs0390
operating system: 5.11 joyent_20170911T171900Z (i86pc)
image uuid: (not set)
panic message: mutex_enter: bad mutex, lp=ffffff597dde7f80
owner=ffffff3c59b39480 thread=ffffff0180912c40
dump content: kernel pages only
The problem is that dbuf_prefetch along with l2arc can create a zio tree
which confuses the parent zio and allows it to complete with while children
still exist. Here's the scenario:
zio tree:
pio
|--- lio
The parent zio, pio, has entered the zio_done stage and begins to check its
children to see there are still some that have not completed. In zio_done(),
the children are checked in the following order:
zio_wait_for_children(zio, ZIO_CHILD_VDEV, ZIO_WAIT_DONE)
zio_wait_for_children(zio, ZIO_CHILD_GANG, ZIO_WAIT_DONE)
zio_wait_for_children(zio, ZIO_CHILD_DDT, ZIO_WAIT_DONE)
zio_wait_for_children(zio, ZIO_CHILD_LOGICAL, ZIO_WAIT_DONE)
If pio, finds any child which has not completed then it stops executing and
goes to sleep. Each call to zio_wait_for_children() will grab the io_lock
while checking the particular child.
In this scenario, the pio has completed the first call to
zio_wait_for_children() to check for any ZIO_CHILD_VDEV children. Since
the only zio in the zio tree right now is the logical zio, lio, then it
completes that call and prepares to check the next child type.
In the meantime, the lio completes and in its callback creates a child vdev
zio, cio. The zio tree looks like this:
zio tree:
pio
|--- lio
|--- cio
The lio then grabs the parent's io_lock and removes itself.
zio tree:
pio
|--- cio
The pio continues to run but has already completed its check for ZIO_CHILD_VDEV
and will erroneously complete. When the child zio, cio, completes it will panic
the system trying to reference the parent zio which has been destroyed.
SOLUTION
========
The fix is to rework the zio_wait_for_children() logic to accept a bitfield
for all the children types that it's interested in checking. The
io_lock will is held the entire time we check all the children types. Since
the function now accepts a bitfield, a simple ZIO_CHILD_BIT() macro is provided
to allow for the conversion between a ZIO_CHILD type and the bitfield used by
the zio_wiat_for_children logic.
Authored by: George Wilson <george.wilson@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Andriy Gapon <avg@FreeBSD.org>
Reviewed by: Youzhong Yang <youzhong@gmail.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Dan McDonald <danmcd@omniti.com>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/8857
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/862ff6d99c
Issue #5918Closes#7168
Project quota is a new ZFS system space/object usage accounting
and enforcement mechanism. Similar as user/group quota, project
quota is another dimension of system quota. It bases on the new
object attribute - project ID.
Project ID is a numerical value to indicate to which project an
object belongs. An object only can belong to one project though
you (the object owner or privileged user) can change the object
project ID via 'chattr -p' or 'zfs project [-s] -p' explicitly.
The object also can inherit the project ID from its parent when
created if the parent has the project inherit flag (that can be
set via 'chattr +P' or 'zfs project -s [-p]').
By accounting the spaces/objects belong to the same project, we
can know how many spaces/objects used by the project. And if we
set the upper limit then we can control the spaces/objects that
are consumed by such project. It is useful when multiple groups
and users cooperate for the same project, or a user/group needs
to participate in multiple projects.
Support the following commands and functionalities:
zfs set projectquota@project
zfs set projectobjquota@project
zfs get projectquota@project
zfs get projectobjquota@project
zfs get projectused@project
zfs get projectobjused@project
zfs projectspace
zfs allow projectquota
zfs allow projectobjquota
zfs allow projectused
zfs allow projectobjused
zfs unallow projectquota
zfs unallow projectobjquota
zfs unallow projectused
zfs unallow projectobjused
chattr +/-P
chattr -p project_id
lsattr -p
This patch also supports tree quota based on the project quota via
"zfs project" commands set as following:
zfs project [-d|-r] <file|directory ...>
zfs project -C [-k] [-r] <file|directory ...>
zfs project -c [-0] [-d|-r] [-p id] <file|directory ...>
zfs project [-p id] [-r] [-s] <file|directory ...>
For "df [-i] $DIR" command, if we set INHERIT (project ID) flag on
the $DIR, then the proejct [obj]quota and [obj]used values for the
$DIR's project ID will be shown as the total/free (avail) resource.
Keep the same behavior as EXT4/XFS does.
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Reviewed-by Ned Bass <bass6@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Fan Yong <fan.yong@intel.com>
TEST_ZIMPORT_POOLS="zol-0.6.1 zol-0.6.2 master"
Change-Id: Ib4f0544602e03fb61fd46a849d7ba51a6005693c
Closes#6290
mmp_write_uberblock() and mmp_write_done() should the same tag
for spa_config_locks.
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Sanjeev Bagewadi <sanjeev.bagewadi@gmail.com>
Closes#6530Closes#7155
8520 lzc_rollback_to should support rolling back to origin
7198 libzfs should gracefully handle EINVAL from lzc_rollback
lzc_rollback_to() should support rolling back to a clone's origin.
The current checks in zfs_ioc_rollback() would not allow that
because the origin snapshot belongs to a different filesystem.
The overly restrictive check was in introduced in 7600, but it
was not a regression as none of the existing tools provided a
way to rollback to the origin.
Authored by: Andriy Gapon <avg@FreeBSD.org>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Approved by: Dan McDonald <danmcd@joyent.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/8520
OpenZFS-issue: https://www.illumos.org/issues/7198
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/78a5a1a25aCloses#7150
With "casesensitivity=mixed", zap_add() could fail when the number of
files/directories with the same name (varying in case) exceed the
capacity of the leaf node of a Fatzap. This results in a ASSERT()
failure as zfs_link_create() does not expect zap_add() to fail. The fix
is to handle these failures and rollback the transactions.
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: Chunwei Chen <david.chen@nutanix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Sanjeev Bagewadi <sanjeev.bagewadi@gmail.com>
Closes#7011Closes#7054
If a corruption happens to be on a root block of an objset, zdb -c will
not correctly report the error, and it will not traverse the datasets
that come after. This is because traverse_visitbp, which does the
callback and reset error for TRAVERSE_HARD, is skipped when traversing
zil is failed in traverse_impl.
Here's example of what 'zdb -eLcc' command looks like on a pool with
damaged objset root:
== before patch:
Traversing all blocks to verify checksums ...
Error counts:
errno count
block traversal size 379392 != alloc 33987072 (unreachable 33607680)
bp count: 172
ganged count: 0
bp logical: 1678336 avg: 9757
bp physical: 130560 avg: 759 compression: 12.85
bp allocated: 379392 avg: 2205 compression: 4.42
bp deduped: 0 ref>1: 0 deduplication: 1.00
SPA allocated: 33987072 used: 0.80%
additional, non-pointer bps of type 0: 71
Dittoed blocks on same vdev: 101
== after patch:
Traversing all blocks to verify checksums ...
zdb_blkptr_cb: Got error 52 reading <54, 0, -1, 0> -- skipping
Error counts:
errno count
52 1
block traversal size 33963520 != alloc 33987072 (unreachable 23552)
bp count: 447
ganged count: 0
bp logical: 36093440 avg: 80745
bp physical: 33699840 avg: 75391 compression: 1.07
bp allocated: 33963520 avg: 75981 compression: 1.06
bp deduped: 0 ref>1: 0 deduplication: 1.00
SPA allocated: 33987072 used: 0.80%
additional, non-pointer bps of type 0: 76
Dittoed blocks on same vdev: 115
==
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Signed-off-by: Chunwei Chen <david.chen@nutanix.com>
Closes#7099
A new interface was added to manipulate the version field of an
inode. Add a inode_set_iversion() wrapper for older kernels and
use the new interface when available.
The i_version field was dropped from the trace point due to the
switch to an atomic64_t i_version type.
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Chunwei Chen <david.chen@nutanix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7148
Authored by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed by: Chris Williamson <chris.williamson@delphix.com>
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Ported-by: Don Brady <don.brady@delphix.com>
We want to be able to run channel programs outside of synching
context. This would greatly improve performance for channel programs
that just gather information, as they won't have to wait for synching
context anymore.
=== What is implemented?
This feature introduces the following:
- A new command line flag in "zfs program" to specify our intention
to run in open context. (The -n option)
- A new flag/option within the channel program ioctl which selects
the context.
- Appropriate error handling whenever we try a channel program in
open-context that contains zfs.sync* expressions.
- Documentation for the new feature in the manual pages.
=== How do we handle zfs.sync functions in open context?
When such a function is found by the interpreter and we are running
in open context we abort the script and we spit out a descriptive
runtime error. For example, given the script below ...
arg = ...
fs = arg["argv"][1]
err = zfs.sync.destroy(fs)
msg = "destroying " .. fs .. " err=" .. err
return msg
if we run it in open context, we will get back the following error:
Channel program execution failed:
[string "channel program"]:3: running functions from the zfs.sync
submodule requires passing sync=TRUE to lzc_channel_program()
(i.e. do not specify the "-n" command line argument)
stack traceback:
[C]: in function 'destroy'
[string "channel program"]:3: in main chunk
=== What about testing?
We've introduced new wrappers for all channel program tests that
run each channel program as both (startard & open-context) and
expect the appropriate behavior depending on the program using
the zfs.sync module.
OpenZFS-issue: https://www.illumos.org/issues/8677
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/17a49e15Closes#6558
Authored by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Andy Stormont <astormont@racktopsystems.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Ported-by: Don Brady <don.brady@delphix.com>
Every time we want to unmount a snapshot (happens during snapshot
deletion or renaming) we unnecessarily iterate through all the
mountpoints in the VFS layer (see zfs_get_vfs).
The current patch completely gets rid of that code and changes
the approach while keeping the behavior of that code path the
same. Specifically, it puts a hold on the dataset/snapshot and
gets its vfs resource reference directly, instead of linearly
searching for it. If that reference exists we attempt to amount
it.
With the above change, it became obvious that the nvlist
manipulations that we do (add_boolean and add_nvlist) take a
significant amount of time ensuring uniqueness of every new
element even though they don't have too. Thus, we updated the
patch so those nvlists are not trying to enforce the uniqueness
of their elements.
A more complete analysis of the problem solved by this patch
can be found below:
https://sdimitro.github.io/post/snap-unmount-perf/
OpenZFS-issue: https://www.illumos.org/issues/8604
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/126118fb
Authored by: Chris Williamson <chris.williamson@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Reviewed by: Brad Lewis <brad.lewis@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Ported-by: Don Brady <don.brady@delphix.com>
ZFS channel programs should be able to create snapshots.
In addition to the base snapshot functionality, this entails extra
logic to handle edge cases which were formerly not possible, such as
creating then destroying a snapshot in the same transaction sync.
OpenZFS-issue: https://www.illumos.org/issues/8600
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/68089b8b
Authored by: Brad Lewis <brad.lewis@delphix.com>
Reviewed by: Chris Williamson <chris.williamson@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Ported-by: Don Brady <don.brady@delphix.com>
ZFS channel programs should be able to perform a rollback.
OpenZFS-issue: https://www.illumos.org/issues/8592
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/d46b5ed6
Authored by: Chris Williamson <chris.williamson@delphix.com>
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Ported-by: Don Brady <don.brady@delphix.com>
zfs.exists() in channel programs doesn't return any result, and should
have a man page entry. This patch corrects zfs.exists so that it
returns a value indicating if the dataset exists or not. It also adds
documentation about it in the man page.
OpenZFS-issue: https://www.illumos.org/issues/8605
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/1e85e111
Authored by: Chris Williamson <chris.williamson@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Approved by: Garrett D'Amore <garrett@damore.org>
Ported-by: Don Brady <don.brady@delphix.com>
Ported-by: John Kennedy <john.kennedy@delphix.com>
OpenZFS-issue: https://www.illumos.org/issues/7431
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/dfc11533
Porting Notes:
* The CLI long option arguments for '-t' and '-m' don't parse on linux
* Switched from kmem_alloc to vmem_alloc in zcp_lua_alloc
* Lua implementation is built as its own module (zlua.ko)
* Lua headers consumed directly by zfs code moved to 'include/sys/lua/'
* There is no native setjmp/longjump available in stock Linux kernel.
Brought over implementations from illumos and FreeBSD
* The get_temporary_prop() was adapted due to VFS platform differences
* Use of inline functions in lua parser to reduce stack usage per C call
* Skip some ZFS Test Suite ZCP tests on sparc64 to avoid stack overflow
zfs_arc_p_aggressive_disable is no more. This PR removes docs
and module parameters for zfs_arc_p_aggressive_disable.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Richard Elling <Richard.Elling@RichardElling.com>
Closes#7135
This patch contains no functional changes. It is solely intended
to resolve cstyle warnings in order to facilitate moving the spl
source code in to the zfs repository.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#681
Currently, the ARC exposes 2 tunables (zfs_arc_min_prefetch_ms
and zfs_arc_min_prescient_prefetch_ms) which are documented
to be specified in milliseconds. However, the code actually
uses the values as though they were in seconds. This patch
adjusts the code to match the names and documentation of the
tunables.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#7126
Remove the unused vmalloc address check, and function mem_to_page
will handle the non-vmalloc address when map it to a physical
address.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Weigang Li <weigang.li@intel.com>
Closes#7125
The keystore.sk_dk_lock should not be held while performing I/O.
Drop the lock when reading from disk and update the code so
they the first successful caller adds the key.
Improve error handling in spa_keystore_create_mapping_impl().
Reviewed by: Thomas Caputi <tcaputi@datto.com>
Reviewed-by: RageLtMan <rageltman@sempervictus>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7112Closes#7115
Currently, os_next_write_raw is a single boolean used for determining
whether or not the next call to dmu_objset_sync() should write out
the objset_phys_t as a raw buffer. Since the boolean is not associated
with a txg, the work simply happens during the next txg, which is not
necessarily the correct one. In the current implementation this issue
was misdiagnosed, resulting in a small hack in dmu_objset_sync() which
seemed to resolve the problem.
This patch changes os_next_write_raw to be an array of booleans, one
for each txg in TXG_OFF and removes the hack.
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#6864
Currently, when a raw zfs send file includes a DRR_OBJECT record
that would decrease the number of levels of an existing object,
the object is reallocated with dmu_object_reclaim() which
creates the new dnode using the old object's nlevels. For non-raw
sends this doesn't really matter, but raw sends require that
nlevels on the receive side match that of the send side so that
the checksum-of-MAC tree can be properly maintained. This patch
corrects the issue by freeing the object completely before
allocating it again in this case.
This patch also corrects several issues with dnode_hold_impl()
and related functions that prevented dnodes (particularly
multi-slot dnodes) from being reallocated properly due to
the fact that existing dnodes were not being fully cleaned up
when they were freed.
This patch adds a test to make sure that zfs recv functions
properly with incremental streams containing dnodes of different
sizes.
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6821Closes#6864
When performing zil_claim() at pool import time, it is
important that encrypted datasets set os_next_write_raw
before writing to the zil_header_t. This prevents the code
from attempting to re-authenticate the objset_phys_t when
it writes it out, which is unnecessary because the
zil_header_t is not protected by either objset MAC and
impossible since the keys aren't loaded yet. Unfortunately,
one of the code paths did not set this flag, which causes
failed ASSERTs during 'zpool import -F'. This patch corrects
this issue.
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#6864Closes#6916
The on-disk format for encrypted datasets protects not only
the encrypted and authenticated blocks themselves, but also
the order and interpretation of these blocks. In order to
make this work while maintaining the ability to do raw
sends, the indirect bps maintain a secure checksum of all
the MACs in the block below it along with a few other
fields that determine how the data is interpreted.
Unfortunately, the current on-disk format erroneously
includes some fields which are not portable and thus cannot
support raw sends. It is not possible to easily work around
this issue due to a separate and much smaller bug which
causes indirect blocks for encrypted dnodes to not be
compressed, which conflicts with the previous bug. In
addition, the current code generates incompatible on-disk
formats on big endian and little endian systems due to an
issue with how block pointers are authenticated. Finally,
raw send streams do not currently include dn_maxblkid when
sending both the metadnode and normal dnodes which are
needed in order to ensure that we are correctly maintaining
the portable objset MAC.
This patch zero's out the offending fields when computing
the bp MAC and ensures that these MACs are always
calculated in little endian order (regardless of the host
system's byte order). This patch also registers an errata
for the old on-disk format, which we detect by adding a
"version" field to newly created DSL Crypto Keys. We allow
datasets without a version (version 0) to only be mounted
for read so that they can easily be migrated. We also now
include dn_maxblkid in raw send streams to ensure the MAC
can be maintained correctly.
This patch also contains minor bug fixes and cleanups.
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#6845Closes#6864Closes#7052
Currently, the ICP contains accelerated assembly code to be
used specifically on CPUs with AES-NI enabled. This code
makes heavy use of the movaps instruction which assumes that
it will be provided aes keys that are 16 byte aligned. This
assumption seems to hold on Illumos, but on Linux some kernel
options such as 'slub_debug=P' will violate it. This patch
changes all instances of this instruction to movups which is
the same except that it can handle unaligned memory.
This patch also adds a few flags which were accidentally never
given to the assembly compiler, resulting in objtool warnings.
Reviewed by: Gvozden Neskovic <neskovic@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Nathaniel R. Lewis <linux.robotdude@gmail.com>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#7065Closes#7108
When scn->scn_maxinflight_bytes has not been initialized it's
possible to hang on the condition variable in scan_exec_io().
This issue was uncovered by ztest and is only possible when
deduplication is enabled through the following call path.
txg_sync_thread()
spa_sync()
ddt_sync_table()
ddt_sync_entry()
dsl_scan_ddt_entry()
dsl_scan_scrub_cb()
dsl_scan_enqueuei()
scan_exec_io()
cv_wait()
Resolve the issue by always initializing scn_maxinflight_bytes
to a reasonable minimum value. This value will be recalculated
in dsl_scan_sync() to pick up changes to zfs_scan_vdev_limit
and the addition/removal of vdevs.
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7098
* Remove 'zfs snap' from zfs help message (OpenZFS sync)
* Update zfs(8) to suggest 'snap' can be used as an alias for 'snapshot'
* Enforce 80 columns limit in help messages
* Remove zfs_disable_dup_eviction from zfs-module-parameters(5)
* Expose zfs_scan_max_ext_gap as a kernel module parameter.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#7087
Introduce kstats about the dbuf hash and dbuf cache
to make it easier to inspect state. This should help
with debugging and understanding of these portions
of the codebase.
Correct format of dbuf kstat file.
Introduce a dbc column to dbufs kstat to indicate if
a dbuf is in the dbuf cache.
Introduce field filtering in the dbufstat python script.
Introduce a no header option to the dbufstat python script.
Introduce a test case to test basic mru->mfu list movement
in the ARC.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#6906
PROBLEM
=======
When `dmu_tx_assign` is called from `zil_lwb_write_issue`, it's possible
for either `ERESTART` or `EIO` to be returned.
If `ERESTART` is returned, this will cause an assertion to fail directly
in `zil_lwb_write_issue`, where the code assumes the return value is
`EIO` if `dmu_tx_assign` returns a non-zero value. This can occur if the
SPA is suspended when `dmu_tx_assign` is called, and most often occurs
when running `zloop`.
If `EIO` is returned, this can cause assertions to fail elsewhere in the
ZIL code. For example, `zil_commit_waiter_timeout` contains the
following logic:
lwb_t *nlwb = zil_lwb_write_issue(zilog, lwb);
ASSERT3S(lwb->lwb_state, !=, LWB_STATE_OPENED);
In this case, if `dmu_tx_assign` returned `EIO` from within
`zil_lwb_write_issue`, the `lwb` variable passed in will not be issued
to disk. Thus, it's `lwb_state` field will remain `LWB_STATE_OPENED` and
this assertion will fail. `zil_commit_waiter_timeout` assumes that after
it calls `zil_lwb_write_issue`, the `lwb` will be issued to disk, and
doesn't handle the case where this is not true; i.e. it doesn't handle
the case where `dmu_tx_assign` returns `EIO`.
SOLUTION
========
This change modifies the `dmu_tx_assign` function such that `txg_how` is
a bitmask, rather than of the `txg_how_t` enum type. Now, the previous
`TXG_WAITED` semantics can be used via `TXG_NOTHROTTLE`, along with
specifying either `TXG_NOWAIT` or `TXG_WAIT` semantics.
Previously, when `TXG_WAITED` was specified, `TXG_NOWAIT` semantics was
automatically invoked. This was not ideal when using `TXG_WAITED` within
`zil_lwb_write_issued`, leading the problem described above. Rather, we
want to achieve the semantics of `TXG_WAIT`, while also preventing the
`tx` from being penalized via the dirty delay throttling.
With this change, `zil_lwb_write_issued` can acheive the semtantics that
it requires by passing in the value `TXG_WAIT | TXG_NOTHROTTLE` to
`dmu_tx_assign`.
Further, consumers of `dmu_tx_assign` wishing to achieve the old
`TXG_WAITED` semantics can pass in the value `TXG_NOWAIT | TXG_NOTHROTTLE`.
Authored by: Prakash Surya <prakash.surya@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed by: Andriy Gapon <avg@FreeBSD.org>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Porting Notes:
- Additionally updated `zfs_tmpfile` to use `TXG_NOTHROTTLE`
OpenZFS-issue: https://www.illumos.org/issues/8997
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/19ea6cb0f9Closes#7084
The intent of this patch is extend the existing deadman code
such that it's flexible enough to be used by both ztest and
on production systems. The proposed changes include:
* Added a new `zfs_deadman_failmode` module option which is
used to dynamically control the behavior of the deadman. It's
loosely modeled after, but independant from, the pool failmode
property. It can be set to wait, continue, or panic.
* wait - Wait for the "hung" I/O (default)
* continue - Attempt to recover from a "hung" I/O
* panic - Panic the system
* Added a new `zfs_deadman_ziotime_ms` module option which is
analogous to `zfs_deadman_synctime_ms` except instead of
applying to a pool TXG sync it applies to zio_wait(). A
default value of 300s is used to define a "hung" zio.
* The ztest deadman thread has been re-enabled by default,
aligned with the upstream OpenZFS code, and then extended
to terminate the process when it takes significantly longer
to complete than expected.
* The -G option was added to ztest to print the internal debug
log when a fatal error is encountered. This same option was
previously added to zdb in commit fa603f82. Update zloop.sh
to unconditionally pass -G to obtain additional debugging.
* The FM_EREPORT_ZFS_DELAY event which was previously posted
when the deadman detect a "hung" pool has been replaced by
a new dedicated FM_EREPORT_ZFS_DEADMAN event.
* The proposed recovery logic attempts to restart a "hung"
zio by calling zio_interrupt() on any outstanding leaf zios.
We may want to further restrict this to zios in either the
ZIO_STAGE_VDEV_IO_START or ZIO_STAGE_VDEV_IO_DONE stages.
Calling zio_interrupt() is expected to only be useful for
cases when an IO has been submitted to the physical device
but for some reasonable the completion callback hasn't been
called by the lower layers. This shouldn't be possible but
has been observed and may be caused by kernel/driver bugs.
* The 'zfs_deadman_synctime_ms' default value was reduced from
1000s to 600s.
* Depending on how ztest fails there may be no cache file to
move. This should not be considered fatal, collect the logs
which are available and carry on.
* Add deadman test cases for spa_deadman() and zio_wait().
* Increase default zfs_deadman_checktime_ms to 60s.
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed by: Thomas Caputi <tcaputi@datto.com>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6999
This reverts commit 093911f194.
Reviewed-by: Chunwei Chen <tuxoko@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#7079
Add missing helper function cv_timedwait_io(), it should be used
when waiting on IO with a specified timeout.
Reviewed-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#674
In case of misaligned I/O sequential requests are not detected as such
due to overlaps in logical block sequence:
dmu_zfetch(fffff80198dd0ae0, 27347, 9, 1)
dmu_zfetch(fffff80198dd0ae0, 27355, 9, 1)
dmu_zfetch(fffff80198dd0ae0, 27363, 9, 1)
dmu_zfetch(fffff80198dd0ae0, 27371, 9, 1)
dmu_zfetch(fffff80198dd0ae0, 27379, 9, 1)
dmu_zfetch(fffff80198dd0ae0, 27387, 9, 1)
This patch makes single block overlap to be counted as a stream hit,
improving performance up to several times.
Authored by: Alexander Motin <mav@FreeBSD.org>
Approved by: Gordon Ross <gwr@nexenta.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Allan Jude <allanjude@freebsd.org>
Reviewed by: Gvozden Neskovic <neskovic@gmail.com>
Reviewed by: George Melikov <mail@gmelikov.ru>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/8835
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/aab6dd482aCloses#7062
usr/src/uts/common/sys/fs/zfs.h
Change ZPROP_INVAL and ZPROP_CONT from macros to enum values. Clang
and GCC both prefer to use unsigned ints to store enums. That was
causing tautological comparison warnings (and likely eliminating
error handling code at compile time) whenever a zfs_prop_t or
zpool_prop_t was compared to ZPROP_INVAL or ZPROP_CONT. Making the
error flags be explicity enum values forces the enum types to be
signed.
ZPROP_INVAL was also compared against two different enum types. I
had to change its name to ZPOOL_PROP_INVAL whenever its compared to
a zpool_prop_t. There are still some places where ZPROP_INVAL or
ZPROP_CONT is compared to a plain int, in code that doesn't know
whether the int is storing a zfs_prop_t or a zpool_prop_t.
usr/src/uts/common/fs/zfs/spa.c
s/ZPROP_INVAL/ZPOOL_PROP_INVAL/
Authored by: Alan Somers <asomers@gmail.com>
Approved by: Gordon Ross <gwr@nexenta.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Igor Kozhukhov <igor@dilos.org>
Reviewed by: George Melikov <mail@gmelikov.ru>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/8652
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/c2de80dc74Closes#7061
In mmp_thread(), emit an MMP specific error message before calling
zio_suspend() so that the administrator will understand why the pool
is being suspended.
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: John L. Hammond <john.hammond@intel.com>
Closes#7048
Authored by: Sean Eric Fagan <sef@ixsystems.com>
Reviewed by: Alek Pinchuk <pinchuk.alek@gmail.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Gordon Ross <gwr@nexenta.com>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Porting Notes:
- Brought #defines in eventdefs.h in line with ZFS on Linux format.
- Updated zfs-events.5 with the new events.
OpenZFS-issue: https://www.illumos.org/issues/8959
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/c862b93eeaCloses#7049
When --enable-asan is provided to configure then build all user
space components with fsanitize=address. For kernel support
use the Linux KASAN feature instead.
https://github.com/google/sanitizers/wiki/AddressSanitizer
When using gcc version 4.8 any test case which intentionally
generates a core dump will fail when using --enable-asan.
The default behavior is to disable core dumps and only newer
versions allow this behavior to be controled at run time with
the ASAN_OPTIONS environment variable.
Additionally, this patch includes some build system cleanup.
* Rules.am updated to set the minimum AM_CFLAGS, AM_CPPFLAGS,
and AM_LDFLAGS. Any additional flags should be added on a
per-Makefile basic. The --enable-debug and --enable-asan
options apply to all user space binaries and libraries.
* Compiler checks consolidated in always-compiler-options.m4
and renamed for consistency.
* -fstack-check compiler flag was removed, this functionality
is provided by asan when configured with --enable-asan.
* Split DEBUG_CFLAGS in to DEBUG_CFLAGS, DEBUG_CPPFLAGS, and
DEBUG_LDFLAGS.
* Moved default kernel build flags in to module/Makefile.in and
split in to ZFS_MODULE_CFLAGS and ZFS_MODULE_CPPFLAGS. These
flags are set with the standard ccflags-y kbuild mechanism.
* -Wframe-larger-than checks applied only to binaries or
libraries which include source files which are built in
both user space and kernel space. This restriction is
relaxed for user space only utilities.
* -Wno-unused-but-set-variable applied only to libzfs and
libzpool. The remaining warnings are the result of an
ASSERT using a variable when is always declared.
* -D_POSIX_PTHREAD_SEMANTICS and -D__EXTENSIONS__ dropped
because they are Solaris specific and thus not needed.
* Ensure $GDB is defined as gdb by default in zloop.sh.
Signed-off-by: DHE <git@dehacked.net>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7027
As a performance optimization Lustre does not strictly update
the SA_ZPL_SIZE when adding/removing from non-directory entries.
This results in entries which cannot be removed through the ZPL
layer even though the ZAP is empty and safe to remove.
Resolve this issue by checking the zap_count() directly instead
on relying on the cached SA_ZPL_SIZE. Micro-benchmarks show no
significant performance impact due to the additional overhead
of using zap_count().
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Alex Zhuravlev <alexey.zhuravlev@intel.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7019
kmem_alloc(0, ...) in userspace returns a leakable pointer.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: DHE <git@dehacked.net>
Issue #6941
When the compressed ARC feature was added in commit d3c2ae1
the method of reference counting in the ARC was modified. As
part of this accounting change the arc_buf_add_ref() function
was removed entirely.
This would have be fine but the arc_buf_add_ref() function
served a second undocumented purpose of updating the ARC access
information when taking a hold on a dbuf. Without this logic
in place a cached dbuf would not migrate its associated
arc_buf_hdr_t to the MFU list. This would negatively impact
the ARC hit rate, particularly on systems with a small ARC.
This change reinstates the missing call to arc_access() from
dbuf_hold() by implementing a new arc_buf_access() function.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6171Closes#6852Closes#6989
Authored by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: John Kennedy <jwk404@gmail.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Brad Lewis <brad.lewis@delphix.com>
Reviewed by: Igor Kozhukhov <igor@dilos.org>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Robert Mustacchi <rm@joyent.com>
Ported-by: Prakash Surya <prakash.surya@delphix.com>
PROBLEM
=======
There's a race condition that exists if `zil_free_lwb` races with either
`zil_commit_waiter_timeout` and/or `zil_lwb_flush_vdevs_done`.
Here's an example panic due to this bug:
> ::status
debugging crash dump vmcore.0 (64-bit) from ip-10-110-205-40
operating system: 5.11 dlpx-5.2.2.0_2017-12-04-17-28-32b6ba51fb (i86pc)
image uuid: 4af0edfb-e58e-6ed8-cafc-d3e9167c7513
panic message:
BAD TRAP: type=e (#pf Page fault) rp=ffffff0010555970 addr=60 occurred in module "zfs" due to a NULL pointer dereference
dump content: kernel pages only
> $c
zio_shrink+0x12()
zil_lwb_write_issue+0x30d(ffffff03dcd15cc0, ffffff03e0730e20)
zil_commit_waiter_timeout+0xa2(ffffff03dcd15cc0, ffffff03d97ffcf8)
zil_commit_waiter+0xf3(ffffff03dcd15cc0, ffffff03d97ffcf8)
zil_commit+0x80(ffffff03dcd15cc0, 9a9)
zfs_write+0xc34(ffffff03dc38b140, ffffff0010555e60, 40, ffffff03e00fb758, 0)
fop_write+0x5b(ffffff03dc38b140, ffffff0010555e60, 40, ffffff03e00fb758, 0)
write+0x250(42, fffffd7ff4832000, 2000)
sys_syscall+0x177()
If there's an outstanding lwb that's in `zil_commit_waiter_timeout`
waiting to timeout, waiting on it's waiter's CV, we must be sure not to
call `zil_free_lwb`. If we end up calling `zil_free_lwb`, then that LWB
may be freed and can result in a use-after-free situation where the
stale lwb pointer stored in the `zil_commit_waiter_t` structure of the
thread waiting on the waiter's CV is used.
A similar situation can occur if an lwb is issued to disk, and thus in
the `LWB_STATE_ISSUED` state, and `zil_free_lwb` is called while the
disk is servicing that lwb. In this situation, the lwb will be freed by
`zil_free_lwb`, which will result in a use-after-free situation when the
lwb's zio completes, and `zil_lwb_flush_vdevs_done` is called.
This race condition is prevented in `zil_close` by calling `zil_commit`
before `zil_free_lwb` is called, which will ensure all outstanding (i.e.
all lwb's in the `LWB_STATE_OPEN` and/or `LWB_STATE_ISSUED` states)
reach the `LWB_STATE_DONE` state before the lwb's are freed
(`zil_commit` will not return untill all the lwb's are
`LWB_STATE_DONE`).
Further, this race condition is prevented in `zil_sync` by only calling
`zil_free_lwb` for lwb's that do not have their `lwb_buf` pointer set.
All lwb's not in the `LWB_STATE_DONE` state will have a non-null value
for this pointer; the pointer is only cleared in
`zil_lwb_flush_vdevs_done`, at which point the lwb's state will be
changed to `LWB_STATE_DONE`.
This race *is* present in `zil_suspend`, leading to this bug.
At first glance, it would appear as though this would not be true
because `zil_suspend` will call `zil_commit`, just like `zil_close`, but
the problem is that `zil_suspend` will set the zilog's `zl_suspend`
field prior to calling `zil_commit`. Further, in `zil_commit`, if
`zl_suspend` is set, `zil_commit` will take a special branch of logic
and use `txg_wait_synced` instead of performing the normal `zil_commit`
logic.
This call to `txg_wait_synced` might be good enough for the data to
reach disk safely before it returns, but it does not ensure that all
outstanding lwb's reach the `LWB_STATE_DONE` state before it returns.
This is because, if there's an lwb "stuck" in
`zil_commit_waiter_timeout`, waiting for it's lwb to timeout, it will
maintain a non-null value for it's `lwb_buf` field and thus `zil_sync`
will not free that lwb. Thus, even though the lwb's data is already on
disk, the lwb will be left lingering, waiting on the CV, and will
eventually timeout and be issued to disk even though the write is
unnecessary.
So, after `zil_commit` is called from `zil_suspend`, we incorrectly
assume that there are not outstanding lwb's, and proceed to free all
lwb's found on the zilog's lwb list. As a result, we free the lwb that
will later be used `zil_commit_waiter_timeout`.
SOLUTION
========
The solution to this, is to ensure all outstanding lwb's complete before
calling `zil_free_lwb` via `zil_destroy` in `zil_suspend`. This patch
accomplishes this goal by forcing the normal `zil_commit` logic when
called from `zil_sync`.
Now, `zil_suspend` will call `zil_commit_impl` which will always use the
normal logic of waiting/issuing lwb's to disk before it returns. As a
result, any lwb's outstanding when `zil_commit_impl` is called will be
guaranteed to reach the `LWB_STATE_DONE` state by the time it returns.
Further, no new lwb's will be created via `zil_commit` since the zilog's
`zl_suspend` flag will be set. This will force all new callers of
`zil_commit` to use `txg_wait_synced` instead of creating and issuing
new lwb's.
Thus, all lwb's left on the zilog's lwb list when `zil_destroy` is
called will be in the `LWB_STATE_DONE` state, and we'll avoid this race
condition.
OpenZFS-issue: https://www.illumos.org/issues/8909
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/ece62b6f8dCloses#6940
Our zfs backed Lustre MDT had soft lockups while under heavy metadata
workloads while handling transaction callbacks from osd_zfs.
The problem is zfs is not taking advantage of the fast path in
Lustre's trans callback handling, where Lustre will skip the calls
to ptlrpc_commit_replies() when it already saw a higher transaction
number.
This patch corrects this, it also has a positive impact on metadata
performance on Lustre with osd_zfs, plus some cleanup in the headers.
A similar issue for ext4/ldiskfs is described on:
https://jira.hpdd.intel.com/browse/LU-6527
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Li Dongyang <dongyang.li@anu.edu.au>
Closes#6986
Use timer_setup() macro and new timeout function definition.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#670Closes#671
When sequential scrubs were merged, all calls to arc_read()
(including prefetch IOs) were given ZIO_PRIORITY_ASYNC_READ.
Unfortunately, this behaves badly with an existing issue where
prefetch IOs cannot be re-prioritized after the issue. The
result is that synchronous reads end up in the same vdev_queue
as the scrub IOs and can have (in some workloads) multiple
seconds of latency.
This patch incorporates 2 changes. The first ensures that all
scrub IOs are given ZIO_PRIORITY_SCRUB to allow the vdev_queue
code to differentiate between these I/Os and user prefetches.
Second, this patch introduces zio_change_priority() to provide
the missing capability to upgrade a zio's priority.
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#6921Closes#6926
When the multihost property is enabled it should be impossible to
import an active pool even using the force (-f) option. This patch
prevents a forced import from succeeding when importing with a
stale cache file.
The root cause of the problem is that the kernel modules trusted
the hostid provided in configuration. This is always correct when
the configuration is generated by scanning for the pool. However,
when using an existing cache file the hostid could be stale which
would result in the activity check being skipped.
Resolve the issue by always using the hostid read from the label
configuration where the best uberblock was found.
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6933Closes#6971
Suppress incorrect warnings from versions of objtool which are not
aware of x86 EVEX prefix instructions used for AVX512.
module/zfs/vdev_raidz_math_avx512bw.o: warning:
objtool: <func+offset>: can't find jump dest instruction at .text
Reviewed-by: Don Brady <don.brady@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6928
This is a purely cosmetic change. The zilog's "zl_writer_lock" field is
being renamed to "zl_issuer_lock" to try and make the code easier to
understand; no other changes are made.
Authored by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: C Fraire <cfraire@me.com>
Approved by: Dan McDonald <danmcd@joyent.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/8603
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/2daf06546bCloses#6927
Authored by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: Brad Lewis <brad.lewis@delphix.com>
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Dan McDonald <danmcd@joyent.com>
Ported-by: Prakash Surya <prakash.surya@delphix.com>
Problem
=======
The current implementation of zil_commit() can introduce significant
latency, beyond what is inherent due to the latency of the underlying
storage. The additional latency comes from two main problems:
1. When there's outstanding ZIL blocks being written (i.e. there's
already a "writer thread" in progress), then any new calls to
zil_commit() will block waiting for the currently oustanding ZIL
blocks to complete. The blocks written for each "writer thread" is
coined a "batch", and there can only ever be a single "batch" being
written at a time. When a batch is being written, any new ZIL
transactions will have to wait for the next batch to be written,
which won't occur until the current batch finishes.
As a result, the underlying storage may not be used as efficiently
as possible. While "new" threads enter zil_commit() and are blocked
waiting for the next batch, it's possible that the underlying
storage isn't fully utilized by the current batch of ZIL blocks. In
that case, it'd be better to allow these new threads to generate
(and issue) a new ZIL block, such that it could be serviced by the
underlying storage concurrently with the other ZIL blocks that are
being serviced.
2. Any call to zil_commit() must wait for all ZIL blocks in its "batch"
to complete, prior to zil_commit() returning. The size of any given
batch is proportional to the number of ZIL transaction in the queue
at the time that the batch starts processing the queue; which
doesn't occur until the previous batch completes. Thus, if there's a
lot of transactions in the queue, the batch could be composed of
many ZIL blocks, and each call to zil_commit() will have to wait for
all of these writes to complete (even if the thread calling
zil_commit() only cared about one of the transactions in the batch).
To further complicate the situation, these two issues result in the
following side effect:
3. If a given batch takes longer to complete than normal, this results
in larger batch sizes, which then take longer to complete and
further drive up the latency of zil_commit(). This can occur for a
number of reasons, including (but not limited to): transient changes
in the workload, and storage latency irregularites.
Solution
========
The solution attempted by this change has the following goals:
1. no on-disk changes; maintain current on-disk format.
2. modify the "batch size" to be equal to the "ZIL block size".
3. allow new batches to be generated and issued to disk, while there's
already batches being serviced by the disk.
4. allow zil_commit() to wait for as few ZIL blocks as possible.
5. use as few ZIL blocks as possible, for the same amount of ZIL
transactions, without introducing significant latency to any
individual ZIL transaction. i.e. use fewer, but larger, ZIL blocks.
In theory, with these goals met, the new allgorithm will allow the
following improvements:
1. new ZIL blocks can be generated and issued, while there's already
oustanding ZIL blocks being serviced by the storage.
2. the latency of zil_commit() should be proportional to the underlying
storage latency, rather than the incoming synchronous workload.
Porting Notes
=============
Due to the changes made in commit 119a394ab0, the lifetime of an itx
structure differs than in OpenZFS. Specifically, the itx structure is
kept around until the data associated with the itx is considered to be
safe on disk; this is so that the itx's callback can be called after the
data is committed to stable storage. Since OpenZFS doesn't have this itx
callback mechanism, it's able to destroy the itx structure immediately
after the itx is committed to an lwb (before the lwb is written to
disk).
To support this difference, and to ensure the itx's callbacks can still
be called after the itx's data is on disk, a few changes had to be made:
* A list of itxs was added to the lwb structure. This list contains
all of the itxs that have been committed to the lwb, such that the
callbacks for these itxs can be called from zil_lwb_flush_vdevs_done(),
after the data for the itxs is committed to disk.
* A list of itxs was added on the stack of the zil_process_commit_list()
function; the "nolwb_itxs" list. In some circumstances, an itx may
not be committed to an lwb (e.g. if allocating the "next" ZIL block
on disk fails), so this list is used to keep track of which itxs
fall into this state, such that their callbacks can be called after
the ZIL's writer pipeline is "stalled".
* The logic to actually call the itx's callback was moved into the
zil_itx_destroy() function. Since all consumers of zil_itx_destroy()
were effectively performing the same logic (i.e. if callback is
non-null, call the callback), it seemed like useful code cleanup to
consolidate this logic into a single function.
Additionally, the existing Linux tracepoint infrastructure dealing with
the ZIL's probes and structures had to be updated to reflect these code
changes. Specifically:
* The "zil__cw1" and "zil__cw2" probes were removed, so they had to be
removed from "trace_zil.h" as well.
* Some of the zilog structure's fields were removed, which affected
the tracepoint definitions of the structure.
* New tracepoints had to be added for the following 3 new probes:
* zil__process__commit__itx
* zil__process__normal__itx
* zil__commit__io__error
OpenZFS-issue: https://www.illumos.org/issues/8585
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/5d95a3aCloses#6566
When zfs_sticky_remove_access() was originally adapted for Linux
a typo was made which altered the intended behavior. As described
in the block comment, the intended behavior is that permission
should be granted when the entry is a regular file and you have
write access. That is, S_ISREG should have been used instead of
S_ISDIR.
Restricting permission to regular files made good sense for older
systems where setting the bit on executable files would instruct
the system to save the program's text segment on the swap device.
On modern systems this behavior has been replaced by the sticky
bit acting as a restricted deletion flag and the plain file
restriction has been relaxed.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6889Closes#6910
Using zio_data_buf_alloc() to allocate the itx's may be unsafe
because the itx->itx_lr.lrc_reclen field is not constant from
allocation to free. Using a different itx->itx_lr.lrc_reclen
size in zio_data_buf_free() can result in the allocation being
returned to the wrong kmem cache.
This issue can be avoided entirely by storing the allocation size
in itx->itx_size and using that for zio_data_buf_free().
Reviewed by: Prakash Surya <prakash.surya@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6912
When d4a72f23 was merged, pss_pass_issued was incorrectly
added to the middle of the pool_scan_stat_t structure
instead of the end. This patch simply corrects this issue.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#6909
Fix a regression accidentally introduced in 1b81ab4 that prevents
'zfs get {user|group}objused@' from correctly reporting the requested
value.
Update "userspace_003_pos.ksh" and "groupspace_003_pos.ksh" to verify
this functionality.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#6908
Fix build errors with gcc 7.2.0 on Gentoo with kernel 4.14
built with CONFIG_GCC_PLUGIN_RANDSTRUCT=y such as:
module/nvpair/nvpair.c:2810:2:error:
positional initialization of field in ?struct? declared with
'designated_init' attribute [-Werror=designated-init]
nvs_native_nvlist,
^~~~~~~~~~~~~~~~~
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Mark Wright <gienah@gentoo.org>
Closes#5390Closes#6903
Resolve new warnings and errors from cppcheck v1.80.
* [lib/libshare/libshare.c:543]: (warning)
Possible null pointer dereference: protocol
* [lib/libzfs/libzfs_dataset.c:2323]: (warning)
Possible null pointer dereference: srctype
* [lib/libzfs/libzfs_import.c:318]: (error)
Uninitialized variable: link
* [module/zfs/abd.c:353]: (error) Uninitialized variable: sg
* [module/zfs/abd.c:353]: (error) Uninitialized variable: i
* [module/zfs/abd.c:385]: (error) Uninitialized variable: sg
* [module/zfs/abd.c:385]: (error) Uninitialized variable: i
* [module/zfs/abd.c:553]: (error) Uninitialized variable: i
* [module/zfs/abd.c:553]: (error) Uninitialized variable: sg
* [module/zfs/abd.c:763]: (error) Uninitialized variable: i
* [module/zfs/abd.c:763]: (error) Uninitialized variable: sg
* [module/zfs/abd.c:305]: (error) Uninitialized variable: tmp_page
* [module/zfs/zpl_xattr.c:342]: (warning)
Possible null pointer dereference: value
* [module/zfs/zvol.c:208]: (error) Uninitialized variable: p
Convert the following suppression to inline.
* [module/zfs/zfs_vnops.c:840]: (error)
Possible null pointer dereference: aiov
Exclude HAVE_UIO_ZEROCOPY and HAVE_DNLC from analysis since
these macro's will never be defined until this functionality
is implemented.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6879
Only access the `b_crypt_hdr` field of an ARC header if the content
is encrypted.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: DHE <git@dehacked.net>
Closes#6877
Currently, scrubs and resilvers can take an extremely
long time to complete. This is largely due to the fact
that zfs scans process pools in logical order, as
determined by each block's bookmark. This makes sense
from a simplicity perspective, but blocks in zfs are
often scattered randomly across disks, particularly
due to zfs's copy-on-write mechanisms.
This patch improves performance by splitting scrubs
and resilvers into a metadata scanning phase and an IO
issuing phase. The metadata scan reads through the
structure of the pool and gathers an in-memory queue
of I/Os, sorted by size and offset on disk. The issuing
phase will then issue the scrub I/Os as sequentially as
possible, greatly improving performance.
This patch also updates and cleans up some of the scan
code which has not been updated in several years.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Authored-by: Saso Kiselkov <saso.kiselkov@nexenta.com>
Authored-by: Alek Pinchuk <apinchuk@datto.com>
Authored-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#3625Closes#6256
The kernel_read & kernel_write functions have always wrapped the
vfs_read & vfs_write functions respectively. However, they could
not be used by vn_rdwr() since the offset wasn't passed as a
pointer. This prevented us from being able to properly update
the file offset.
Linux 4.14 unexported vfs_read & vfs_write but also changed the
signature of kernel_read & kernel_write to provide the needed
functionality. Use these updated functions when available.
Reviewed-by: Pritam Baral <pritam@pritambaral.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#656Closes#667
The correct way to determine if a dnode is dirty is to check
if any of the dn->dn_dirty_link's are active. Relying solely
on the dn->dn_dirtyctx can result in the dnode being mistakenly
reported as clean.
Reviewed-by: Chunwei Chen <tuxoko@gmail.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#3125Closes#6867
On Linux, ftruncate(2) always changes the file timestamps, even if the
file size is not changed. However, in case of a successfull
truncate(2), the timestamps are updated only if the file size changes.
This translates to the VFS calling the ZFS Posix Layer "setattr"
function (zpl_setattr) with ATTR_MTIME and ATTR_CTIME unconditionally
set on the iattr mask only when doing a ftruncate(2), while the
truncate(2) is left to the filesystem implementation to be dealt with.
This behaviour is consistent with POSIX:2004/SUSv3 specifications
where there's no explicit requirement for file size changes to update
the timestamps only for ftruncate(2):
http://pubs.opengroup.org/onlinepubs/009695399/functions/truncate.htmlhttp://pubs.opengroup.org/onlinepubs/009695399/functions/ftruncate.html
This has been later updated in POSIX:2008/SUSv4 where, for both
truncate(2)/ftruncate(2), there's no mention of this size change
requirement:
http://austingroupbugs.net/view.php?id=489http://pubs.opengroup.org/onlinepubs/9699919799/functions/truncate.htmlhttp://pubs.opengroup.org/onlinepubs/9699919799/functions/ftruncate.html
Unfortunately the Linux VFS is still calling into the ZPL without
ATTR_MTIME/ATTR_CTIME set in the truncate(2) case: we fix this by
explicitly updating the timestamps when detecting the ATTR_SIZE bit,
which is always set in do_truncate(), on the iattr mask.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#6811Closes#6819
If the receive or rollback is performed while filesystem is upgrading
the objset may be evicted in `dsl_dataset_clone_swap_sync_impl`. This
will lead to NULL pointer dereference when upgrade tries to access
evicted objset.
This commit adds long hold of dataset during whole upgrade process.
The receive and rollback will return an EBUSY error until the
upgrade is not finished.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Arkadiusz Bubała <arkadiusz.bubala@open-e.com>
Closes#5295Closes#6837
After doing a recursive raw receive, zfs userspace performs
a final pass to adjust the encryption root hierarchy as
needed. Unfortunately, the FORCE_INHERIT ioctl had a bug
which caused the encryption root to always be assigned to
the direct parent instead of the inheriting parent. This
patch simply fixes this issue.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alek Pinchuk <apinchuk@datto.com>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#6847Closes#6848
In __dbuf_hold_impl(), if a buffer is currently syncing and is still
referenced from db_data, a copy is made in case it is dirtied again in
the txg. Previously, the buffer for the copy was simply allocated with
arc_alloc_buf() which doesn't handle compressed or encrypted buffers
(which are a special case of a compressed buffer). The result was
typically an invalid memory access because the newly-allocated buffer
was of the uncompressed size.
This commit fixes the problem by handling the 2 compressed cases,
encrypted and unencrypted, respectively, with arc_alloc_raw_buf() and
arc_alloc_compressed_buf().
Although using the proper allocation functions fixes the invalid memory
access by allocating a buffer of the compressed size, another unrelated
issue made it impossible to properly detect compressed buffers in the
first place. The header's compression flag was set to ZIO_COMPRESS_OFF
in arc_write() when it was possible that an attached buffer was actually
compressed. This commit adds logic to only set ZIO_COMPRESS_OFF in
the non-ZIO_RAW case which wil handle both cases of compressed buffers
(encrypted or unencrypted).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tim Chase <tim@chase2k.com>
Closes#5742Closes#6797
Reviewed by: Yuri Pankov <yuripv@gmx.com>
Reviewed by: Igor Kozhukhov <igor@dilos.org>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Authored by: Toomas Soome <tsoome@me.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/8607
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/b852c2f5Closes#6842
When the 128KB block is compressed to less than 4KB, the pointer
to the Footer is not in the end of the compressed buffer, that's
because the Header offset was added twice for this case. So there
is a gap between the Footer and the compressed buffer.
1. Always compute the Footer pointer address from the start of the
last page.
2. Remove the un-used workaroud code which has been verified fixed
with the latest driver and this fix.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Weigang Li <weigang.li@intel.com>
Closes#6827
Fixed build regression in non-debug builds from recent cleanups of
c89 workarounds.
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@delphix.com>
Closes#6832
With PR 5756 the zfs module now supports c99 and the
remaining past c89 workarounds can be undone.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Don Brady <don.brady@delphix.com>
Closes#6816
On systems with CONFIG_SMP turned off, spin_is_locked always returns
false causing these assertions to fail. Remove them as suggested in
zfsonlinux/zfs#6558.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: James Cowgill <james.cowgill@mips.com>
Closes#665
Both vn_rename and vn_remove have been historically problematic
to implement reliably. Rather than fixing them yet again they
are being removed.
Reviewed-by: Arkadiusz Bubala <arkadiusz.bubala@open-e.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#648Closes#661
Fix compiler warnings in zdb. With these changes, FreeBSD can compile
zdb with all compiler warnings enabled save -Wunused-parameter.
usr/src/cmd/zdb/zdb.c
usr/src/cmd/zdb/zdb_il.c
usr/src/uts/common/fs/zfs/sys/sa.h
usr/src/uts/common/fs/zfs/sys/spa.h
Fix numerous warnings, including:
* const-correctness
* shadowing global definitions
* signed vs unsigned comparisons
* missing prototypes, or missing static declarations
* unused variables and functions
* Unreadable array initializations
* Missing struct initializers
usr/src/cmd/zdb/zdb.h
Add a header file to declare common symbols
usr/src/lib/libzpool/common/sys/zfs_context.h
usr/src/uts/common/fs/zfs/arc.c
usr/src/uts/common/fs/zfs/dbuf.c
usr/src/uts/common/fs/zfs/spa.c
usr/src/uts/common/fs/zfs/txg.c
Add a function prototype for zk_thread_create, and ensure that every
callback supplied to this function actually matches the prototype.
usr/src/cmd/ztest/ztest.c
usr/src/uts/common/fs/zfs/sys/zil.h
usr/src/uts/common/fs/zfs/zfs_replay.c
usr/src/uts/common/fs/zfs/zvol.c
Add a function prototype for zil_replay_func_t, and ensure that
every function of this type actually matches the prototype.
usr/src/uts/common/fs/zfs/sys/refcount.h
Change FTAG so it discards any constness of __func__, necessary
since existing APIs expect it passed as void *.
Porting Notes:
- Many of these fixes have already been applied to Linux. For
consistency the OpenZFS version of a change was applied if the
warning was addressed in an equivalent but different fashion.
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Prakash Surya <prakash.surya@delphix.com>
Authored by: Alan Somers <asomers@gmail.com>
Approved by: Richard Lowe <richlowe@richlowe.net>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/8081
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/843abe1b8aCloses#6787
When dumping objects larger than 128PiB it's possible for do_dump() to
miscalculate the FREE_RECORD offset due to an integer overflow
condition: this prevents the receiving end from correctly restoring
the dumped object.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Fabian Grünbichler <f.gruenbichler@proxmox.com>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#6760
8558 lwp_create() returns EAGAIN on system with more than 80K ZFS filesystems
On a system with more than 80K ZFS filesystems, we've seen cases
where lwp_create() will start to fail by returning EAGAIN. The
problem being, for each of those 80K ZFS filesystems, a taskq will
be created for each dataset as part of the ZIL for each dataset.
Porting Notes:
- The new nomem taskq kstat was dropped.
- Added module options and documentation for new tunings
zfs_zil_clean_taskq_nthr_pct, zfs_zil_clean_taskq_minalloc,
zfs_zil_clean_taskq_maxalloc, and zfs_sync_taskq_batch_pct.
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Sebastien Roy <sebastien.roy@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Authored by: Prakash Surya <prakash.surya@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Chris Dunlop <chris@onthe.net.au>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/8558
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/216d772
8602 remove unused "dp_early_sync_tasks" field from "dsl_pool" structure
Reviewed by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Authored by: Prakash Surya <prakash.surya@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Chris Dunlop <chris@onthe.net.au>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/8602
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/2bcb545Closes#6779
Added -n flag to zpool reopen that allows a running scrub
operation to continue if there is a device with Dirty Time Log.
By default if a component device has a DTL and zpool reopen
is executed all running scan operations will be restarted.
Added functional tests for `zpool reopen`
Tests covers following scenarios:
* `zpool reopen` without arguments,
* `zpool reopen` with pool name as argument,
* `zpool reopen` while scrubbing,
* `zpool reopen -n` while scrubbing,
* `zpool reopen -n` while resilvering,
* `zpool reopen` with bad arguments.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: Arkadiusz Bubała <arkadiusz.bubala@open-e.com>
Closes#6076Closes#6746
History commands and events were being suppressed for the
'zpool create' command since the history object did not
yet exist. Create the object earlier so this history
doesn't get lost.
Split the pool_destroy event in to pool_destroy and
pool_export so they may be distinguished.
Updated events_001_pos and events_002_pos test cases. They
now check for the expected history events and were reworked
to be more reliable.
Reviewed-by: Nathaniel Clark <nathaniel.l.clark@intel.com>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6712Closes#6486
Support integration with new QAT products: Intel(R) C62x Chipset,
or Atom(R) C3000 Processor Product Family SoC:
1. Detect new file name in auto-conf.
2. Change MAX_INSTANCES to 48.
3. Change "num_inst" to U16 to clean a build warning.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Weigang Li <weigang.li@intel.com>
Closes#6767
The only place vn_rename and vn_remove are used is when writing
out an updated pool configuration file. By truncating the file
instead of renaming and removing it we can avoid having to implement
these interfaces entirely. Functionally an empty cache file is
treated the same as a missing cache file. This is particularly
advantageous because the Linux kernel has never provided a way
to reliably implement vn_rename and vn_remove.
The cachefile_004_pos.ksh test case was updated to understand
that an empty cache file is the same as a missing one.
The zfs-import-* systemd service files were not updated to use
ConditionFileNotEmpty in place of ConditionPathExists. This
means that after exporting all pools and rebooting new pools
will not the scanned for on the next boot. This small change
should not impact normal usage since pools are not exported
as part of a normal shutdown.
Documentation was updated accordingly.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Arkadiusz Bubała <arkadiusz.bubala@open-e.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes zfsonlinux/spl#648
Closes#6753
This small patch fixes an issue where dmu_free_long_object_raw()
calls dnode_hold() after freeing the dnode a line above.
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#6766
This PR includes fixes for bugs and documentation issues found
after the encryption patch was merged and general code improvements
for long-term maintainability.
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Issue #6526Closes#6639Closes#6703
Cloese #6706Closes#6714Closes#6595
This patch resolves an issue where raw sends would fail to send
encryption parameters if the wrapping key was unloaded and reloaded
before the data was sent and the dataset wass not an encryption root.
The code attempted to lookup the values from the wrapping key which
was not being initialized upon reload. This change forces the code to
lookup the correct value from the encryption root's DSL Crypto Key.
Unfortunately, this issue led to the on-disk DSL Crypto Key for some
non-encryption root datasets being left with zeroed out encryption
parameters. However, this should not present a problem since these
values are never looked at and are overrwritten upon changing keys.
This patch also fixes an issue where raw, resumable sends were not
being cleaned up appropriately if an invalid DSL Crypto Key was
received.
Signed-off-by: Tom Caputi <tcaputi@datto.com>
This patch resolves an issue where spa_keystore_change_key_sync_impl()
incorrectly recursed into clone DSL Directories while recursively
rewrapping encryption keys. Clones share keys with their origins, so
this logic was incorrect.
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Several issues were uncovered by running stress tests with zfs
encryption and raw sends in particular. The issues and their
associated fixes are as follows:
* arc_read_done() has the ability to chain several requests for
the same block of data via the arc_callback_t struct. In these
cases, the ARC would only use the first request's dsobj from
the bookmark to decrypt the data. This is problematic because
the first request might be a prefetch zio which is able to
handle the key not being loaded, while the second might use a
different key that it is sure will work. The fix here is to
pass the dsobj with each individual arc_callback_t so that each
request can attempt to decrypt the data separately.
* DRR_FREE and DRR_FREEOBJECT records in a send file were not
having their transactions properly tagged as raw during raw
sends, which caused a panic when the dbuf code attempted to
decrypt these blocks.
* traverse_prefetch_metadata() did not properly set
ZIO_FLAG_SPECULATIVE when issuing prefetch IOs.
* Added a few asserts and code cleanups to ensure these issues
are more detectable in the future.
Signed-off-by: Tom Caputi <tcaputi@datto.com>
* PBKDF2 implementation changed to OpenSSL implementation.
* HKDF implementation moved to its own file and tests
added to ensure correctness.
* Removed libzfs's now unnecessary dependency on libzpool
and libicp.
* Ztest can now create and test encrypted datasets. This is
currently disabled until issue #6526 is resolved, but
otherwise functions as advertised.
* Several small bug fixes discovered after enabling ztest
to run on encrypted datasets.
* Fixed coverity defects added by the encryption patch.
* Updated man pages for encrypted send / receive behavior.
* Fixed a bug where encrypted datasets could receive
DRR_WRITE_EMBEDDED records.
* Minor code cleanups / consolidation.
Signed-off-by: Tom Caputi <tcaputi@datto.com>
This patch resolves a minor issue where an ASSERT in
metaslab_passivate() that only applies to non weight-based
metaslabs was erroneously applied to all metaslabs.
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Normally a SPARC processor runs in big endian mode. Save the extra labor
needed for little endian machines when the target is a big endian one
(sparc).
Signed-off-by: Pengcheng Xu <i@jsteward.moe>
Passing arguments explicitly into SHA1Transform() increases the number of
registers abailable to the compiler, hence leaving more local and out registers
available. The missing symbol of sha1_consts[], which prevents compiling on
SPARC, is added back, which speeds up the process of utilizing the relative
constants.
This should fix#6738.
Signed-off-by: Pengcheng Xu <i@jsteward.moe>
CID 147474: Logically dead code (DEADCODE)
Remove ternary operator and return `error` directly.
Currently return value is derived from a ternary operator. The
conditional is always true. The ternary operator is therefore
redundant i.e dead code.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Closes#6723
When sending an incremental stream based on a snapshot, the receiving
side must have the same base snapshot. Thus we do not need to send
FREEOBJECTS records for any objects past the maximum one which exists
locally.
This allows us to send incremental streams (again) to older ZFS
implementations (e.g. ZoL < 0.7) which actually try to free all objects
in a FREEOBJECTS record, instead of bailing out early.
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Fabian Grünbichler <f.gruenbichler@proxmox.com>
Closes#5699Closes#6507Closes#6616
All objects after the last written or freed object are not supposed to
exist after receiving the stream. Free them accordingly, as if a
freeobjects record for them had been included in the stream.
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Fabian Grünbichler <f.gruenbichler@proxmox.com>
Closes#5699Closes#6507Closes#6616
With the addition of the ABD changes consumption of the virtual
address space has been greatly reduced. This exposed an issue on
CONFIG_HIGHMEM systems where free memory was being calculated
incorrectly. Functionally this didn't cause any major problems
prior to ABD because a lack of available virtual address space
was used as an indicator of low memory.
This patch makes the following changes to address the issue and
in the process realigns the code further with OpenZFS. There
are no substantive changes in behavior for 64-bit systems.
* Added CONFIG_HIGHMEM case to the arc_all_memory() and
arc_free_memory() functions to only consider low memory pages
on CONFIG_HIGHMEM systems.
* The arc_free_memory() function was updated to return bytes
instead of pages to be consistent with the other helper
functions. In user space we make up some reasonable values
since currently only testing is performed in this context.
* Adds three new values to the arcstats kstat to provide visibility
in to the ARC's assessment of the memory situation:
memory_all_bytes, memory_free_bytes, and memory_available_bytes.
* Added kmem_reap() call to arc_available_memory() for 32-bit
builds to realign code with OpenZFS.
* Reduced size of test file in /async_destroy_001_pos.ksh to
speed up test case. Multiple txgs are still required.
* Move vdevs used by zpool_clear_001_pos and zpool_upgrade_002_pos
to TEST_BASE_DIR location to speed up test cases.
Reviewed-by: David Quigley <david.quigley@intel.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#5352Closes#6734
When decrementing the struct_size and scatter_chunk_waste kstats
the value needs to be cast to an int on 32-bit systems.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6721
Currently `if` statement includes an assignment (from a function return
value) and a equality check. The parenthesis are in the incorrect place,
currently the code clobbers the function return value because of this.
We can fix this by simplifying the `if` statement.
`if (foo != 0)`
can be more succinctly expressed as
`if (foo)`
Remove the equality check, add parenthesis to correct the statement.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Chris Dunlop <chris@onthe.net.au>
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Closes#6685Close#6719
The vdev_copy_uberblocks() function should use abd_alloc_linear() to
allocate ub_abd, because abd_to_buf(ub_abd)) is used later.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Isaac Huang <he.huang@intel.com>
Closes#6718Closes#6713
The avl_update_* functions are never used by ZFS and are therefore
being removed. They're barely even used in Illumos. Additionally,
simplify avl_add() by using a VERIFY which produces exactly the same
behavior under Linux.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6716
When receiving a FREEOBJECTS record, receive_freeobjects()
incorrectly skips a freed object in some cases. Specifically, this
happens when the first object in the range to be freed doesn't exist,
but the second object does. This leaves an object allocated on disk
on the receiving side which is unallocated on the sending side, which
may cause receiving subsequent incremental streams to fail.
The bug was caused by an incorrect increment of the object index
variable when current object being freed doesn't exist. The
increment is incorrect because incrementing the object index is
handled by a call to dmu_object_next() in the increment portion of
the for loop statement.
Add test case that exposes this bug.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ned Bass <bass6@llnl.gov>
Closes#6694Closes#6695
It's often useful to have access to txg history for debugging
purposes. This patch changes the default from 0 to 100 TXGs
worth of history preserved.
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed by: Prakash Surya <prakash.surya@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Alek Pinchuk <apinchuk@datto.com>
Closes#6691
Commit d3c2ae1 introduced a dbuf cache with a default size of the
minimum of 100M or 1/32 maximum ARC size. (These figures may be adjusted
using dbuf_cache_max_bytes and dbuf_cache_max_shift.) The dbuf cache
is counted as metadata for the purposes of ARC size calculations.
On a 1GB box the ARC maximum size defaults to c_max 493M which gives a
dbuf cache default minimum size of 15.4M, and the ARC metadata defaults
to minimum 16M. I.e. the dbuf cache is an significant proportion of the
minimum metadata size. With other overheads involved this actually means
the ARC metadata doesn't get down to the minimum.
This patch dynamically scales the dbuf cache to the target ARC size
instead of statically scaling it to the maximum ARC size. (The scale is
still set by dbuf_cache_max_shift and the maximum size is still fixed by
dbuf_cache_max_bytes.) Using the target ARC size rather than the current
ARC size is done to help the ARC reach the target rather than simply
focusing on the current size.
Reviewed-by: Chunwei Chen <tuxoko@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Chris Dunlop <chris@onthe.net.au>
Issue #6506Closes#6561
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: DHE <git@dehacked.net>
Closes#6672
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Elling <Richard.Elling@RichardElling.com>
Closes#652Closes#651
Rename it as mmp_random_leaf() since it is defined in mmp.c.
The earlier implementation could end up spinning forever if a pool had a
vdev marked writeable, none of whose children were writeable. It also
did not guarantee that if a writeable leaf vdev existed, it would be
found.
Reimplement to recursively walk the device tree to select the leaf. It
searches the entire tree, so that a return value of (NULL) indicates
there were no usable leaves in the pool; all were either not writeable
or had pending mmp writes.
It still chooses the starting child randomly at each level of the tree,
so if the pool's devices are healthy, the mmp writes go to random leaves
with an even distribution. This was verified by testing using
zfs_multihost_history enabled.
Reviewed by: Thomas Caputi <tcaputi@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#6631Closes#6665
Increase the default arc_c_min value to which whichever is larger,
either 32M or 1/32 of total system memory. This is advantageous for
systems with more than 1G of memory where performance issues may
occur when the ARC is allowed to collapse below a minimum size.
At the same time we want to use the bare minimum value which is
still functional so the filesystem can be used in very low memory
environments.
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6659
This symbol is needed by Lustre for the same reason it was needed
by the ZPL. It should have been exported when the original patch
was merged.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Alex Zhuravlev <bzzz@whamcloud.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6660
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Feng Sun <loyou85@gmail.com>
Closes#6658
ZFS buildbot STYLE builder was moved to Ubuntu 17.04
which has a newer version of cppcheck. Handle the
new cppcheck errors.
uu_* functions removed in this commit were unused
and effectively dead code. They are now retired.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#6653
generic_start_io_acct/generic_end_io_acct in the master
branch of the linux kernel requires that the request_queue
be provided.
Move the logic from freemem in the spl to arc_free_memory
in arc.c. Do this so we can take advantage of global_page_state
interface checks in zfs.
Upstream kernel replaced struct block_device with
struct gendisk in struct bio. Determine if the
function bio_set_dev exists during configure
and have zfs use that if it exists.
bio_set_dev https://github.com/torvalds/linux/commit/74d4699
global_node_page_state https://github.com/torvalds/linux/commit/75ef718
io acct https://github.com/torvalds/linux/commit/d62e26b
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#6635
Changing any metadata, should modify the ctime.
Reviewed-by: Chunwei Chen <tuxoko@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: gaurkuma <gauravk.18@gmail.com>
Closes#3644Closes#6586
On pool import when the old cache file is removed
the ereport.fs.zfs.config_cache_write event is generated.
Because zpool export always removes cache file it happens
every export - import sequence.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Arkadiusz Bubała <arkadiusz.bubala@open-e.com>
Closes#6617
The portion of the zvol_replay_write() handler responsible for
replaying indirect log records for some reason never existed.
As a result indirect log records were not being correctly replayed.
This went largely unnoticed since the majority of zvol log records
were of the type WR_COPIED or WR_NEED_COPY prior to OpenZFS 7578.
This patch updates zvol_replay_write() to correctly handle these
log records and adds a new test case which verifies volume replay
to prevent any regression. The existing test case which verified
replay on filesystem was renamed slog_replay_fs.ksh for clarity.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6603Closes#6615
This reverts commit 65dcb0f67a until
a comprehensive fix is finalized. The stricter interior dnode
detection in 4c5b89f59e and the new
test case added by this patch revealed a issue with resizing
dnodes when receiving an incremental backup stream.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #6576
Refactor dmu_object_alloc_dnsize() and dnode_hold_impl() to simplify the
code, fix errors introduced by commit dbeb879 (PR #6117) interacting
badly with large dnodes, and improve performance.
* When allocating a new dnode in dmu_object_alloc_dnsize(), update the
percpu object ID for the core's metadnode chunk immediately. This
eliminates most lock contention when taking the hold and creating the
dnode.
* Correct detection of the chunk boundary to work properly with large
dnodes.
* Separate the dmu_hold_impl() code for the FREE case from the code for
the ALLOCATED case to make it easier to read.
* Fully populate the dnode handle array immediately after reading a
block of the metadnode from disk. Subsequently the dnode handle array
provides enough information to determine which dnode slots are in use
and which are free.
* Add several kstats to allow the behavior of the code to be examined.
* Verify dnode packing in large_dnode_008_pos.ksh. Since the test is
purely creates, it should leave very few holes in the metadnode.
* Add test large_dnode_009_pos.ksh, which performs concurrent creates
and deletes, to complement existing test which does only creates.
With the above fixes, there is very little contention in a test of about
200,000 racing dnode allocations produced by tests 'large_dnode_008_pos'
and 'large_dnode_009_pos'.
name type data
dnode_hold_dbuf_hold 4 0
dnode_hold_dbuf_read 4 0
dnode_hold_alloc_hits 4 3804690
dnode_hold_alloc_misses 4 216
dnode_hold_alloc_interior 4 3
dnode_hold_alloc_lock_retry 4 0
dnode_hold_alloc_lock_misses 4 0
dnode_hold_alloc_type_none 4 0
dnode_hold_free_hits 4 203105
dnode_hold_free_misses 4 4
dnode_hold_free_lock_misses 4 0
dnode_hold_free_lock_retry 4 0
dnode_hold_free_overflow 4 0
dnode_hold_free_refcount 4 57
dnode_hold_free_txg 4 0
dnode_allocate 4 203154
dnode_reallocate 4 0
dnode_buf_evict 4 23918
dnode_alloc_next_chunk 4 4887
dnode_alloc_race 4 0
dnode_alloc_next_block 4 18
The performance is slightly improved for concurrent creates with
16+ threads, and unchanged for low thread counts.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#5396Closes#6522Closes#6414Closes#6564
When receiving an incremental backup stream, call
dmu_object_reclaim_dnsize() if an object's dnode size differs between
the incremental source and target. Otherwise it may appear that a
dnode which has shrunk is still occupying slots which are in fact
free. This will cause a failure to receive new objects that should
occupy the now-free slots.
Add a test case to verify that an incremental stream containing
objects with changed dnode sizes can be received without error. This
test case fails without this change.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ned Bass <bass6@llnl.gov>
Closes#6366Closes#6576
Add a helper function to trim the tailing new line. While we're
here use this new hook to immediately apply the new scheduler.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#3356Closes#6573
Add a small wrapper around libzfs_core`lzc_send_space() to libzfs so
that every legacy ZFS_IOC_SEND consumer, along with their userland
counterpart estimate_ioctl(), can leverage ZFS_IOC_SEND_SPACE to
request send space estimation.
The legacy functionality in zfs_ioc_send() is left untouched for
compatibility purposes.
Reviewed by: Thomas Caputi <tcaputi@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#6029
Authored by: Richard Lowe <richlowe@richlowe.net>
Reviewed by: Josef 'Jeff' Sipek <jeffpc@josefsipek.net>
Reviewed by: Igor Kozhukhov <ikozhukhov@gmail.com>
Reviewed by: Andy Stormont <andyjstormont@gmail.com>
Approved by: Dan McDonald <danmcd@omniti.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/2976
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/5c5f137Closes#6582
Authored by: Eli Rosenthal <eli.rosenthal@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Igor Kozhukhov <ikozhukhov@gmail.com>
Approved by: Gordon Ross <gordon.ross@nexenta.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/7028
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/86f617eCloses#6583
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Sebastien Roy <sebastien.roy@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Robert Mustacchi <rm@joyent.com>
Approved by: Dan McDonald <danmcd@omniti.com>
Reviewed-by: Don Brady <dev.fs.zfs@gmail.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/7261
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/48dd5e6Closes#6579
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Prashanth Sreenivasa <pks@delphix.com>
Reviewed by: Robert Mustacchi <rm@joyent.com>
Approved by: Dan McDonald <danmcd@joyent.com>
Reviewed-by: Don Brady <dev.fs.zfs@gmail.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/8375
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/843c211Closes#6578
Fix a few nits in the comments from large dnodes. Also import
some of the commit message as a comment in the code, making
it more accessible.
Reviewed-by: @rottegift
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Wilson <george.wilson@delphix.com>
Signed-off-by: Matt Ahrens <mahrens@delphix.com>
Closes#6551
vm_node_stat must be used instead of vm_zone_stat. Unfortunately the
old code still compiles potentially leading to silent failure of
arc_evictable_memory()
AKAMAI: CR 3816601: Regression in zfs dropcache test
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Chunwei Chen <tuxoko@gmail.com>
Signed-off-by: Debabrata Banerjee <dbanerje@akamai.com>
Closes#6528
Remove harmless duplicate multilist_link_init() introduced by
commit d3c2ae1.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Signed-off-by: Chris Dunlop <chris@onthe.net.au>
Closes#6552
This patch fixes several issues discovered after
the encryption patch was merged:
* Fixed a bug where encrypted datasets could attempt
to receive embedded data records.
* Fixed a bug where dirty records created by the recv
code wasn't properly setting the dr_raw flag.
* Fixed a typo where a dmu_tx_commit() was changed to
dmu_tx_abort()
* Fixed a few error handling bugs unrelated to the
encryption patch in dmu_recv_stream()
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#6512Closes#6524Closes#6545
Use fnvlist on user input would allow user to easily panic zfs.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Alek Pinchuk <apinchuk@datto.com>
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Closes#6529
vdev_queue:
- Track the last position of each vdev, including the io size,
in order to detect linear access of the following zio.
- Remove duplicate `vq_lastoffset`
vdev_mirror:
- Correctly calculate the zio offset (signedness issue)
- Deprecate `vdev_queue_register_lastoffset()`
- Add `VDEV_LABEL_START_SIZE` to zio offset of leaf vdevs
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Gvozden Neskovic <neskovic@gmail.com>
Closes#6461
Since OpenZFS 7578 (1b7c1e5) if we have a ZVOL with logbias=throughput
we will force WR_INDIRECT itxs in zvol_log_write() setting itx->itx_lr
offset and length to the offset and length of the BIO from
zvol_write()->zvol_log_write(): these offset and length are later used
to take a range lock in zillog->zl_get_data function: zvol_get_data().
Now suppose we have a ZVOL with blocksize=8K and push 4K writes to
offset 0: we will only be range-locking 0-4096. This means the
ASSERTion we make in dbuf_unoverride() is no longer valid because now
dmu_sync() is called from zilog's get_data functions holding a partial
lock on the dbuf.
Fix this by taking a range lock on the whole block in zvol_get_data().
Reviewed-by: Chunwei Chen <tuxoko@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#6238Closes#6315Closes#6356Closes#6477
It's not enough to preserve/restore MS_RDONLY on the superblock flags
to avoid remounting a snapshot read-write: be explicit about our
intentions to the VFS layer so the readonly bit is updated correctly
in do_remount_sb().
Reviewed-by: Chunwei Chen <tuxoko@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#6510Closes#6515
* Removed zpios kmod, utility, headers and man page.
* Removed unused scripts zpios-profile/*, zpios-test/*,
zpool-config/*, smb.sh, zpios-sanity.sh, zpios-survey.sh,
zpios.sh, and zpool-create.sh.
* Removed zfs-script-config.sh.in. When building 'make' generates
a common.sh with in-tree path information from the common.sh.in
template. This file and sourced by the test scripts and used
for in-tree testing, it is not included in the packages. When
building packages 'make install' uses the same template to
create a new common.sh which is appropriate for the packaging.
* Removed unused functions/variables from scripts/common.sh.in.
Only minimal path information and configuration environment
variables remain.
* Removed unused scripts from scripts/ directory.
* Remaining shell scripts in the scripts directory updated to
cleanly pass shellcheck and added to checked scripts.
* Renamed tests/test-runner/cmd/ to tests/test-runner/bin/ to
match install location name.
* Removed last traces of the --enable-debug-dmu-tx configure
options which was retired some time ago.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6509
Added a 'corrupt' error option that will flip a bit in the data
after a read operation. This is useful for generating checksum
errors at the device layer (in a mirror config for example). It
is also used to validate the diagnosis of checksum errors from
the zfs diagnosis engine.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@intel.com>
Closes#6345
This change incorporates three major pieces:
The first change is a keystore that manages wrapping
and encryption keys for encrypted datasets. These
commands mostly involve manipulating the new
DSL Crypto Key ZAP Objects that live in the MOS. Each
encrypted dataset has its own DSL Crypto Key that is
protected with a user's key. This level of indirection
allows users to change their keys without re-encrypting
their entire datasets. The change implements the new
subcommands "zfs load-key", "zfs unload-key" and
"zfs change-key" which allow the user to manage their
encryption keys and settings. In addition, several new
flags and properties have been added to allow dataset
creation and to make mounting and unmounting more
convenient.
The second piece of this patch provides the ability to
encrypt, decyrpt, and authenticate protected datasets.
Each object set maintains a Merkel tree of Message
Authentication Codes that protect the lower layers,
similarly to how checksums are maintained. This part
impacts the zio layer, which handles the actual
encryption and generation of MACs, as well as the ARC
and DMU, which need to be able to handle encrypted
buffers and protected data.
The last addition is the ability to do raw, encrypted
sends and receives. The idea here is to send raw
encrypted and compressed data and receive it exactly
as is on a backup system. This means that the dataset
on the receiving system is protected using the same
user key that is in use on the sending side. By doing
so, datasets can be efficiently backed up to an
untrusted system without fear of data being
compromised.
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#494Closes#5769
When doing read on a file open with O_SYNC, it will trigger zil_commit.
However for snapshot, there's no zil, so we shouldn't be doing that.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Closes#6478Closes#6494
The pool name can be 256 chars long. Today, in /proc/spl/kstat/zfs/
the name is limited to < 32 characters. This change is to allows
bigger pool names.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: gaurkuma <gauravk.18@gmail.com>
Closes#6481
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: gaurkuma <gauravk.18@gmail.com>
Closes#641
