The order in fs/Makefile doesn't matter,
the order in fs/Kconfig is preserved (ext2 is included as the first
thing in the first if BUILD block, and only once), but I don't think it
matters much either, realistically
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13316
When doing a manual TRIM on a zpool, the metaslab being TRIMmed is
potentially re-enabled before all queued TRIM zios for that metaslab
have completed. Since TRIM zios have the lowest priority, it is
possible to get into a situation where allocations occur from the
just re-enabled metaslab and cut ahead of queued TRIMs to the same
metaslab. If the ranges overlap, this will cause corruption.
We were able to trigger this pretty consistently with a small single
top-level vdev zpool (i.e. small number of metaslabs) with heavy
parallel write activity while performing a manual TRIM against a
somewhat 'slow' device (so TRIMs took a bit of time to complete).
With the patch, we've not been able to recreate it since. It was on
illumos, but inspection of the OpenZFS trim code looks like the
relevant pieces are largely unchanged and so it appears it would be
vulnerable to the same issue.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jason King <jking@racktopsystems.com>
Illumos-issue: https://www.illumos.org/issues/15939Closes#15395
Over its history this the dirty dnode test has been changed between
checking for a dnodes being on `os_dirty_dnodes` (`dn_dirty_link`) and
`dn_dirty_record`.
de198f2d9 Fix lseek(SEEK_DATA/SEEK_HOLE) mmap consistency
2531ce372 Revert "Report holes when there are only metadata changes"
ec4f9b8f3 Report holes when there are only metadata changes
454365bba Fix dirty check in dmu_offset_next()
66aca2473 SEEK_HOLE should not block on txg_wait_synced()
Also illumos/illumos-gate@c543ec060dillumos/illumos-gate@2bcf0248e9
It turns out both are actually required.
In the case of appending data to a newly created file, the dnode proper
is dirtied (at least to change the blocksize) and dirty records are
added. Thus, a single logical operation is represented by separate
dirty indicators, and must not be separated.
The incorrect dirty check becomes a problem when the first block of a
file is being appended to while another process is calling lseek to skip
holes. There is a small window where the dnode part is undirtied while
there are still dirty records. In this case, `lseek(fd, 0, SEEK_DATA)`
would not know that the file is dirty, and would go to
`dnode_next_offset()`. Since the object has no data blocks yet, it
returns `ESRCH`, indicating no data found, which results in `ENXIO`
being returned to `lseek()`'s caller.
Since coreutils 9.2, `cp` performs sparse copies by default, that is, it
uses `SEEK_DATA` and `SEEK_HOLE` against the source file and attempts to
replicate the holes in the target. When it hits the bug, its initial
search for data fails, and it goes on to call `fallocate()` to create a
hole over the entire destination file.
This has come up more recently as users upgrade their systems, getting
OpenZFS 2.2 as well as a newer coreutils. However, this problem has been
reproduced against 2.1, as well as on FreeBSD 13 and 14.
This change simply updates the dirty check to check both types of dirty.
If there's anything dirty at all, we immediately go to the "wait for
sync" stage, It doesn't really matter after that; both changes are on
disk, so the dirty fields should be correct.
Sponsored-by: Klara, Inc.
Sponsored-by: Wasabi Technology, Inc.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Rich Ercolani <rincebrain@gmail.com>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Closes#15571Closes#15526
The Linux 5.16.14 kernel's coccicheck caught this. The semantic
patch that caught it was:
./scripts/coccinelle/misc/flexible_array.cocci
However, unlike the cases where the GNU zero length array extension had
been used, coccicheck would not suggest patches for the older style
single member arrays. That was good because blindly changing them would
break size calculations in most cases.
Therefore, this required care to make sure that we did not break size
calculations. In the case of `indirect_split_t`, we use
`offsetof(indirect_split_t, is_child[is->is_children])` to calculate
size. This might be subtly wrong according to an old mailing list
thread:
https://inbox.sourceware.org/gcc-prs/20021226123454.27019.qmail@sources.redhat.com/T/
That is because the C99 specification should consider the flexible array
members to start at the end of a structure, but compilers prefer to put
padding at the end. A suggestion was made to allow compilers to allocate
padding after the VLA like compilers already did:
http://std.dkuug.dk/JTC1/SC22/WG14/www/docs/n983.htm
However, upon thinking about it, whether or not we allocate end of
structure padding does not matter, so using offsetof() to calculate the
size of the structure is fine, so long as we do not mix it with sizeof()
on structures with no array members.
In the case that we mix them and padding causes offsetof(struct_t,
vla_member[0]) to differ from sizeof(struct_t), we would be doing unsafe
operations if we underallocate via `offsetof()` and then overcopy via
sizeof().
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14372
Update the META file to reflect compatibility with the 6.5
kernel.
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
The statechange-slot_off.sh zedlet which was added in #15200
needed to be installed so it's included by the packages.
Additional testing has also shown that multiple retries are
often needed for the script to operate reliably.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#15210
If ZED_POWER_OFF_ENCLOUSRE_SLOT_ON_FAULT is enabled in zed.rc, then
power off the drive's slot in the enclosure if it becomes FAULTED.
This can help silence misbehaving drives. This assumes your drive
enclosure fully supports slot power control via sysfs.
Reviewed-by: @AllKind
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#15200
When register_sysctl_table() is unavailable we fail to properly
unregister sysctl entries under "kernel/spl".
This leads to errors like the following when spl is unloaded/reloaded,
making impossible to properly reload the spl module:
[ 746.995704] sysctl duplicate entry: /kernel/spl/kmem/slab_kvmem_total
Fix by cleaning up all the sub-entries inside "kernel/spl" when the
spl module is unloaded.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Andrea Righi <andrea.righi@canonical.com>
Closes#15239
If we fail to create a proc entry in spl_proc_init() we may end up
calling unregister_sysctl_table() twice: one in the failure path of
spl_proc_init() and another time during spl_proc_fini().
Avoid the double call to unregister_sysctl_table() and while at it
refactor the code a bit to reduce code duplication.
This was accidentally introduced when the spl code was
updated for Linux 6.5 compatibility.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ameer Hamza <ahamza@ixsystems.com>
Signed-off-by: Andrea Righi <andrea.righi@canonical.com>
Closes#15234Closes#15235
Using the filemap_splice_read function for the splice_read handler was
leading to occasional data corruption under certain circumstances. Favor
using copy_splice_read instead, which does not demonstrate the same
erroneous behavior under the tested failure cases.
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#15164
The generic_file_splice_read function was removed in Linux 6.5 in favor
of filemap_splice_read. Add an autoconf test for filemap_splice_read and
use it if it is found as the handler for .splice_read in the
file_operations struct. Additionally, ITER_PIPE was removed in 6.5. This
change removes the ITER_* macros that OpenZFS doesn't use from being
tested in config/kernel-vfs-iov_iter.m4. The removal of ITER_PIPE was
causing the test to fail, which also affected the code responsible for
setting the .splice_read handler, above. That behavior caused run-time
panics on Linux 6.5.
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#15155
Additionally, the .child element of ctl_table has been removed in 6.5.
This change adds a new test for the pre-6.5 register_sysctl_table()
function, and uses the old code in that case. If it isn't found, then
the parentage entries in the tables are removed, and the register_sysctl
call is provided the paths of "kernel/spl", "kernel/spl/kmem", and
"kernel/spl/kstat" directly, to populate each subdirectory over three
calls, as is the new API.
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#15138
This reverts commit b35374fd64 as there
are error messages when loading the SPL module. Errors seemed to be tied
to duplicate a duplicate entry.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Brian Atkinson <batkinson@lanl.gov>
Closes#15134
An iov_iter_type() function to access the "type" member of the struct
iov_iter was added at one point. Move the conditional logic to decide
which method to use for accessing it into a macro and simplify the
zpl_uio_init code.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#15100
The iov_iter->iov member is now iov_iter->__iov and must be accessed via
the accessor function iter_iov(). Create a wrapper that is conditionally
compiled to use the access method appropriate for the target kernel
version.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#15100
Multiple changes to the blkdev API were introduced in Linux 6.5. This
includes passing (void* holder) to blkdev_put, adding a new
blk_holder_ops* arg to blkdev_get_by_path, adding a new blk_mode_t type
that replaces uses of fmode_t, and removing an argument from the release
handler on block_device_operations that we weren't using. The open
function definition has also changed to take gendisk* and blk_mode_t, so
update it accordingly, too.
Implement local wrappers for blkdev_get_by_path() and
vdev_blkdev_put() so that the in-line calls are cleaner, and place the
conditionally-compiled implementation details inside of both of these
local wrappers. Both calls are exclusively used within vdev_disk.c, at
this time.
Add blk_mode_is_open_write() to test FMODE_WRITE / BLK_OPEN_WRITE
The wrapper function is now used for testing using the appropriate
method for the kernel, whether the open mode is writable or not.
Emphasize fmode_t arg in zvol_release is not used
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#15099
When disk_check_media_change() exists, then define
zfs_check_media_change() to simply call disk_check_media_change() on
the bd_disk member of its argument. Since disk_check_media_change()
is newer than when revalidate_disk was present in bops, we should
be able to safely do this via a macro, instead of recreating a new
implementation of the inline function that forces revalidation.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#15101
Additionally, the .child element of ctl_table has been removed in 6.5.
This change adds a new test for the pre-6.5 register_sysctl_table()
function, and uses the old code in that case. If it isn't found, then
the parentage entries in the tables are removed, and the register_sysctl
call is provided the paths of "kernel/spl", "kernel/spl/kmem", and
"kernel/spl/kstat" directly, to populate each subdirectory over three
calls, as is the new API.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#15098
The disk_check_media_change() function was added which replaces
bdev_check_media_change. This change was introduced in 6.5rc1
444aa2c58cb3b6cfe3b7cc7db6c294d73393a894 and the new function takes a
gendisk* as its argument, no longer a block_device*. Thus, bdev->bd_disk
is now used to pass the expected data.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#15060
This change was introduced in Linux commit
7ba150834b840f6f5cdd07ca69a4ccf39df59a66
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#15059
When a kmem cache is exhausted and needs to be expanded a new
slab is allocated. KM_SLEEP callers can block and wait for the
allocation, but KM_NOSLEEP callers were incorrectly allowed to
block as well.
Resolve this by attempting an emergency allocation as a best
effort. This may fail but that's fine since any KM_NOSLEEP
consumer is required to handle an allocation failure.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Adam Moss <c@yotes.com>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Unfortunately, even after e79b6807, I still, much more rarely,
tripped asserts when playing with many ctldir mounts at once.
Since this appears to happen if we dispatched twice too fast, just
ignore it. We don't actually need to do anything if someone already
started doing it for us.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#14462
On Linux, sometimes, when ZFS goes to unmount an automounted snap,
it fails a VERIFY check on debug builds, because taskq_cancel_id
returned ENOENT after not finding the taskq it was trying to cancel.
This presumably happens when it already died for some reason; in this
case, we don't really mind it already being dead, since we're just
going to dispatch a new task to unmount it right after.
So we just ignore it if we get back ENOENT trying to cancel here,
retry a couple times if we get back the only other possible condition
(EBUSY), and log to dbgmsg if we got anything but ENOENT or success.
(We also add some locking around taskqid, to avoid one or two cases
of two instances of trying to cancel something at once.)
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#11632Closes#12670
Update the META file to reflect compatibility with the 6.4 kernel.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Lahfa <ryan@lahfa.xyz>
Closes#15125
For large JBODs the log message "zfs_iter_vdev: no match" can
account for the bulk of the log messages (over 70%). Since this
message is purely informational and not that useful we remove it.
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#15086Closes#15094
We would see zed assert on one of our systems if we powered off a
slot. Further examination showed zfs_retire_recv() was reporting
a GUID of 0, which in turn would return a NULL nvlist. Add
in a check for a zero GUID.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#15084
Unlike regular receive, raw receive require destination to have the
same block structure as the source. In case of dnode reclaim this
triggers two special cases, requiring special handling:
- If dn_nlevels == 1, we can change the ibs, but dnode_set_blksz()
should not dirty the data buffer if block size does not change, or
durign receive dbuf_dirty_lightweight() will trigger assertion.
- If dn_nlevels > 1, we just can't change the ibs, dnode_set_blksz()
would fail and receive_object would trigger assertion, so we should
destroy and recreate the dnode from scratch.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#15039
The previous code was checking zfs_is_namespace_prop() only for the
last property on the list. If one was not "namespace", then remount
wasn't called. To fix that move zfs_is_namespace_prop() inside the
loop and remount if at least one of properties was "namespace".
Reviewed-by: Umer Saleem <usaleem@ixsystems.com>
Reviewed-by: Ameer Hamza <ahamza@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#15000
With the latest L2ARC fixes, 2 seconds is too long to wait for
quiescence of arcstats like l2_size. Shorten this interval to avoid
having the persistent L2ARC tests in ZTS prematurely terminated.
Signed-off-by: George Amanakis <gamanakis@gmail.com>
If this is not done, and the pool has an ashift other than the default
(at the moment 9) then the following happens:
1) vdev_alloc() assigns the ashift of the pool to L2ARC device, but
upon export it is not stored anywhere
2) at the first import, vdev_open() sees an vdev_ashift() of 0 and
assigns the logical_ashift, which is 9
3) reading the contents of L2ARC, including the header fails
4) L2ARC buffers are not restored in ARC.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#14313Closes#14963
While commit bcd5321 adjusts the write size based on the size of the log
block, this happens after comparing the unadjusted write size to the
evicted (target) size.
In this case l2ad_hand will exceed l2ad_evict and violate an assertion
at the end of l2arc_write_buffers().
Fix this by adding the max log block size to the allocated size of the
buffer to be committed before comparing the result to the target
size.
Also reset the l2arc_trim_ahead ZFS module variable when the adjusted
write size exceeds the size of the L2ARC device.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#14936Closes#14954
l2arc_write_size() should return the write size after adjusting for trim
and overhead of the L2ARC log blocks. Also take into account the
allocated size of log blocks when deciding when to stop writing buffers
to L2ARC.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#14939
l2arc_evict() performs the adjustment of the size of buffers to be
written on L2ARC unnecessarily. l2arc_write_size() is called right
before l2arc_evict() and performs those adjustments.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#14828
482da24e2 missed arc_buf_destroy() calls on log parse errors, possibly
leaking up to 128KB of memory per dataset during ZIL replay.
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Given:
/sbin/zfs list filling/a-zvol<TAB> -o space,refratio
The rest of the cmdline gets vored by:
/sbin/zfs list filling/a-zvolcannot open 'filling/a-zvol':
operation not applicable to datasets of this type
With -x (fragment):
+ COMPREPLY=($(compgen -W "$(__zfs_match_snapshot)" -- "$cur"))
+++ __zfs_match_snapshot
+++ local base_dataset=filling/dziadtop-nowe-duchy
+++ [[ filling/dziadtop-nowe-duchy != filling/dziadtop-nowe-duchy ]]
+++ [[ filling/dziadtop-nowe-duchy != '' ]]
+++ __zfs_list_datasets filling/dziadtop-nowe-duchy
+++ /sbin/zfs list -H -o name -s name -t filesystem
-r filling/dziadtop-nowe-duchy
+++ tail -n +2
cannot open 'filling/dziadtop-nowe-duchy':
operation not applicable to datasets of this type
+++ echo filling/dziadtop-nowe-duchy
+++ echo filling/dziadtop-nowe-duchy@
++ compgen -W 'filling/dziadtop-nowe-duchy
This properly completes with:
$ /sbin/zfs list filling/a-zvol<TAB> -o space,refratio
filling/a-zvol filling/a-zvol@
$ /sbin/zfs list filling/a-zvol<cursor> -o space,refratio
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Backport-of: 5ece420f03Closes#12820
Two problems led to unexpected behaviour of the scriptlets:
1) Newer DKMS versions change the formatting of "dkms status":
(old) zfs, 2.1.2, 5.14.10-300.fc35.x86_64, x86_64: installed
(new) zfs/2.1.2, 5.14.10-300.fc35.x86_64, x86_64: installed
Which broke a conditional determining whether to uninstall.
2) zfs_config.h not packaged properly, but was attempted to be read
in the %preun scriptlet:
CONFIG_H="/var/lib/dkms/zfs/2.1.2/*/*/zfs_config.h"
Which broke the uninstallation of the module, which left behind a
dangling symlink, which broke DKMS entirely with this error:
Error! Could not locate dkms.conf file.
File: /var/lib/dkms/zfs/2.1.1/source/dkms.conf does not exist.
This change attempts to simplify life by:
* Avoiding parsing anything (less prone to future breakage)
* Uses %posttrans instead of %post for module installation, because
%post happens before %preun, while %posttrans happens afterwards
* Unconditionally reinstall module on upgrade, which is less
efficient but the trade-off is that it's more reliable
Alternative approaches could involve fixing the existing parsing bugs
or improving the logic, but this comes at the cost of complexity and
possible future bugs.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jeremy Visser <jeremyvisser@google.com>
Closes#10463Closes#13182
- Clang 15 doesn't support `-fno-ipa-sra` anymore. Do a separate
check for `-fno-ipa-sra` support by $KERNEL_CC.
- Don't enable `-mgeneral-regs-only` for certain module files.
Fix#13260
- Scope `GCC diagnostic ignored` statements to GCC only. Clang
doesn't need them to compile the code.
Porting notes:
- Moved the stanzas removing -mgeneral-regs-only to Makefile.in
since they wouldn't readily work in Kbuild.in and that did.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: szubersk <szuberskidamian@gmail.com>
Closes#13260Closes#14150Closes#14624
Ported-by: Rich Ercolani <rincebrain@gmail.com
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Update the META file to reflect compatibility with the 6.3 kernel.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Add a new union member of flexible array to dnode_phys_t and use
it in the macro so we can silence the memcpy() fortify error.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Youzhong Yang <yyang@mathworks.com>
Closes#14737
Linux kernel 6.3 changed a bunch of APIs to use the dedicated idmap
type for mounts (struct mnt_idmap), we need to detect these changes
and make zfs work with the new APIs.
NOTE: This backport only includes the configure checks to detect
the 6.3 idmap API changes. It does not include support for idmap.
When provided the idmap variable is ignored in most case in the
same way the user_ns argument was ignored. This change is solely
to provide compatibility with the new interfaces.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Youzhong Yang <yyang@mathworks.com>
Closes#14682
The type def of writepage_t in kernel 6.3 is changed to take
struct folio* as the first argument. We need to detect this
change and pass correct function to write_cache_pages().
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Youzhong Yang <yyang@mathworks.com>
Closes#14699
Linux since 4.7 makes interface 'cpu_has_feature' to use jump labels on
powerpc if CONFIG_JUMP_LABEL_FEATURE_CHECKS is enabled, in this case
however the inline function references GPL-only symbol
'cpu_feature_keys'.
ZFS currently uses 'cpu_has_feature' either directly or indirectly from
several places; while it is unknown how this issue didn't break ZFS on
64-bit little-endian powerpc, it is known to break ZFS with many Linux
versions on both 32-bit and 64-bit big-endian powerpc.
Until this issue is fixed in Linux, we have to workaround it by
overriding affected inline functions without depending on
'cpu_feature_keys'.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: WHR <msl0000023508@gmail.com>
Closes#14590
As of the 4.13 kernel filemap_range_has_page() can be used to
check if there is a page mapped in a given file range. When
available this interface should be used which eliminates the
need for the zp->z_is_mapped boolean.
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#14493
Page writebacks with WB_SYNC_NONE can take several seconds to complete
since they wait for the transaction group to close before being
committed. This is usually not a problem since the caller does not
need to wait. However, if we're simultaneously doing a writeback
with WB_SYNC_ALL (e.g via msync), the latter can block for several
seconds (up to zfs_txg_timeout) due to the active WB_SYNC_NONE
writeback since it needs to wait for the transaction to complete
and the PG_writeback bit to be cleared.
This commit deals with 2 cases:
- No page writeback is active. A WB_SYNC_ALL page writeback starts
and even completes. But when it's about to check if the PG_writeback
bit has been cleared, another writeback with WB_SYNC_NONE starts.
The sync page writeback ends up waiting for the non-sync page
writeback to complete.
- A page writeback with WB_SYNC_NONE is already active when a
WB_SYNC_ALL writeback starts. The WB_SYNC_ALL writeback ends up
waiting for the WB_SYNC_NONE writeback.
The fix works by carefully keeping track of active sync/non-sync
writebacks and committing when beneficial.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Shaan Nobee <sniper111@gmail.com>
Closes#12662Closes#12790
There seems to be no reason for ZIL blocks to be limited by 128KB
other than replay code is written in such a way. This change does
not increase the limit yet, just removes the artificial limitation.
Avoided extra memcpy() may save us a second during replay.
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
At least for RAIDZ zio_shrink() does not reduce zio size, but reduced
wsz in that case likely results in writing uninitialized memory.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14853
We only need to know if ZIO has any parent there. We do not care if
it has more than one, but use of zio_unique_parent() == NULL asserts
that.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14823
- There is no reason to assert that added gang is not empty. It
may be weird to add an empty gang, but it is legal.
- When moving chain list from the added gang clear its size, or it
will trigger assertion in abd_verify() when that gang is freed.
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14816
TX_COMMIT has no on-disk representation and does not produce any more
dirty data. It should not wait for anything, and even just skipping
the checks if not waiting gives improvement noticeable in profiler.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Prakash Surya <prakash.surya@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14798
Gang ABDs without childred are legal, and they do have zero size.
For other ABD types zero size doesn't have much sense and likely
not working correctly now.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14795
In the case of a regular compilation, the compiler
raises a warning for a dsl_deadlist_merge function, that
the stack size is to large. In debug build this can
generate an error.
Move large structures to heap.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Mariusz Zaborski <mariusz.zaborski@klarasystems.com>
Sponsored-by: Klara, Inc.
Sponsored-by: Wasabi Technology, Inc.
Closes#14524
A NULL pointer will occur when doing a 'zfs send -S' on a dataset that
is still being received. The problem is that the new 'send' will
rightfully fail to own the datasets (i.e. dsl_dataset_own_force() will
fail), but then dmu_send() will still do the dsl_dataset_disown().
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Luís Henriques <henrix@camandro.org>
Closes#14903Closes#14890
CLOCK_MONOTONIC_RAW is only a thing on Linux and macOS. I'm not
actually sure why the previous hardcoding of a constant didn't
error out, but when we removed it, it sure does now.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Rich Ercolani <rincebrain@gmail.com>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12995
It became illegal to not have them as of
5f6df177758b9dff88e4b6069aeb2359e8b0c493 ("vfs: validate that vop
vectors provide all or none fplookup vops") upstream.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#14788
Under certain loads, the following panic is hit:
panic: page fault
KDB: stack backtrace:
#0 0xffffffff805db025 at kdb_backtrace+0x65
#1 0xffffffff8058e86f at vpanic+0x17f
#2 0xffffffff8058e6e3 at panic+0x43
#3 0xffffffff808adc15 at trap_fatal+0x385
#4 0xffffffff808adc6f at trap_pfault+0x4f
#5 0xffffffff80886da8 at calltrap+0x8
#6 0xffffffff80669186 at vgonel+0x186
#7 0xffffffff80669841 at vgone+0x31
#8 0xffffffff8065806d at vfs_hash_insert+0x26d
#9 0xffffffff81a39069 at sfs_vgetx+0x149
#10 0xffffffff81a39c54 at zfsctl_snapdir_lookup+0x1e4
#11 0xffffffff8065a28c at lookup+0x45c
#12 0xffffffff806594b9 at namei+0x259
#13 0xffffffff80676a33 at kern_statat+0xf3
#14 0xffffffff8067712f at sys_fstatat+0x2f
#15 0xffffffff808ae50c at amd64_syscall+0x10c
#16 0xffffffff808876bb at fast_syscall_common+0xf8
The page fault occurs because vgonel() will call VOP_CLOSE() for active
vnodes. For this reason, define vop_close for zfsctl_ops_snapshot. While
here, define vop_open for consistency.
After adding the necessary vop, the bug progresses to the following
panic:
panic: VERIFY3(vrecycle(vp) == 1) failed (0 == 1)
cpuid = 17
KDB: stack backtrace:
#0 0xffffffff805e29c5 at kdb_backtrace+0x65
#1 0xffffffff8059620f at vpanic+0x17f
#2 0xffffffff81a27f4a at spl_panic+0x3a
#3 0xffffffff81a3a4d0 at zfsctl_snapshot_inactive+0x40
#4 0xffffffff8066fdee at vinactivef+0xde
#5 0xffffffff80670b8a at vgonel+0x1ea
#6 0xffffffff806711e1 at vgone+0x31
#7 0xffffffff8065fa0d at vfs_hash_insert+0x26d
#8 0xffffffff81a39069 at sfs_vgetx+0x149
#9 0xffffffff81a39c54 at zfsctl_snapdir_lookup+0x1e4
#10 0xffffffff80661c2c at lookup+0x45c
#11 0xffffffff80660e59 at namei+0x259
#12 0xffffffff8067e3d3 at kern_statat+0xf3
#13 0xffffffff8067eacf at sys_fstatat+0x2f
#14 0xffffffff808b5ecc at amd64_syscall+0x10c
#15 0xffffffff8088f07b at fast_syscall_common+0xf8
This is caused by a race condition that can occur when allocating a new
vnode and adding that vnode to the vfs hash. If the newly created vnode
loses the race when being inserted into the vfs hash, it will not be
recycled as its usecount is greater than zero, hitting the above
assertion.
Fix this by dropping the assertion.
FreeBSD-issue: https://bugs.freebsd.org/bugzilla/show_bug.cgi?id=252700
Reviewed-by: Andriy Gapon <avg@FreeBSD.org>
Reviewed-by: Mateusz Guzik <mjguzik@gmail.com>
Reviewed-by: Alek Pinchuk <apinchuk@axcient.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Rob Wing <rob.wing@klarasystems.com>
Co-authored-by: Rob Wing <rob.wing@klarasystems.com>
Submitted-by: Klara, Inc.
Sponsored-by: rsync.net
Closes#14501
Noticed while attempting to change FreeBSD's boolean_t into an actual
bool: in include/sys/zfs_ioctl_impl.h, zfs_vfs_held() is declared to
return a boolean_t, but in module/os/freebsd/zfs/zfs_ioctl_os.c it is
defined to return an int. Make the definition match the declaration.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Dimitry Andric <dimitry@andric.com>
Closes#14776
When the special_small_blocks property is being set during a pool
create it enforces a limit of 128KiB even if the pool's record size
is larger.
If the recordsize property is being set during a pool create, then
use that value instead of the default SPA_OLD_MAXBLOCKSIZE value.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <dev.fs.zfs@gmail.com>
Closes#13815Closes#14811
The zpool_resilver_concurrent test case requires the ZED which is not used
on FreeBSD. Add this test to the known list of skipped tested for FreeBSD.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#14904
The auto_replace_001_pos test case does not reliably pass on
Fedora 37 and newer. Until the test case can be updated to make
it reliable add it to the list of "maybe" exceptions on Linux.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #14851Closes#14852
Add snapshot_002_pos to the known list of occasional failures
for FreeBSD until it can be made entirely reliable.
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #14831Closes#14832
We use block_device_wait to wait for the zvol block device to
actually appear, and we log the result of the dd calls by using
an intermediate file.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: John Wren Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#14767
When a vdev is degraded or faulted, we refuse to expand it when doing
online -e. However, we also don't actually cause the online command
to fail, even though the disk didn't expand. This is confusing and
misleading, and can result in violated expectations.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes 14145
The kmem allocation in zfs_prune_aliases() will trigger a large
allocation warning on systems with 64K pages. Resolve this by
switching to vmem_alloc() which internally uses kvmalloc() so the
right allocator will be used based on the allocation size.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8491Closes#14694
zpool initialize functions well for touching every free byte...once.
But if we want to do it again, we're currently out of luck.
So let's add zpool initialize -u to clear it.
Co-authored-by: Rich Ercolani <rincebrain@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12451Closes#14873
Before allowing the ZED to mark a vdev as REMOVED due to a
hotplug event confirm that it is non-responsive with probe.
Any device which can be successfully probed should be left
ONLINE to prevent a healthy pool from being incorrectly
SUSPENDED. This may occur for at least the following two
scenarios.
1) Drive expansion (zpool online -e) in VMware environments.
If, during the partition resize operation, a partition is
removed and re-created then udev will send a removed event.
2) Re-scanning the namespaces of an NVMe device (nvme ns-rescan)
may result in a udev remove and add event being delivered.
Finally, update the ZED to only kick in a spare when the
removal was successful.
Reviewed-by: Ameer Hamza <ahamza@ixsystems.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #14859Closes#14861
For draid vdevs it was possible to initiate both the
sequential and healing resilver at same time.
This fixes the following two scenarios.
1) There's a window where a sequential rebuild can
be started via ZED even if a healing resilver has been
scheduled.
- This is fixed by adding additional check in
spa_vdev_attach() for any scheduled resilver and return
appropriate error code when a resilver is already in
progress.
2) It was possible for zpool clear to start a healing
resilver when it wasn't needed at all. This occurs because
during a vdev_open() the device is presumed to be healthy not
until the device is validated by vdev_validate() and it's set
unavailable. However, by this point an async resilver will
have already been requested if the DTL isn't empty.
- This is fixed by cancelling the SPA_ASYNC_RESILVER
request immediately at the end of vdev_reopen() when a resilver
is unneeded.
Finally, added a testcase in ZTS for verification.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Dipak Ghosh <dipak.ghosh@hpe.com>
Signed-off-by: Akash B <akash-b@hpe.com>
Closes#14881Closes#14892
When using zdb to output the value of an xattr only interpret it
as printable characters if the entire byte array is printable.
Additionally, if the --parseable option is set always output the
buffer contents as octal for easy parsing.
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#14830
Provides an interface which callers can use to declare a write when
the exact starting offset in not yet known. Since the full range
being updated is not available only the first L0 block at the
provided offset will be prefetched.
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#14819
The pam ZTS tests were reporting a buffer overflow on F38, possibly
due to F38 now setting _FORTIFY_SOURCE=3 by default. gdb and
valgrind narrowed this down to a snprintf() buffer overflow in
zfs_key_config_modify_session_counter(). I'm not clear why this
particular snprintf() was being flagged as an overflow, but when
I replaced it with an asprintf(), the test passed reliably.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#14802Closes#14842
If we receive a DRR_FREEOBJECTS as the first entry in an object range,
this might end up producing a hole if the freed objects were the
only existing objects in the block.
If the txg starts syncing before we've processed any following
DRR_OBJECT records, this leads to a possible race where the backing
arc_buf_t gets its psize set to 0 in the arc_write_ready() callback
while still being referenced from a dirty record in the open txg.
To prevent this, we insert a txg_wait_synced call if the first
record in the range was a DRR_FREEOBJECTS that actually
resulted in one or more freed objects.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: David Hedberg <david.hedberg@findity.com>
Sponsored by: Findity AB
Closes#11893Closes#14358
spa_import() relies on a pool config fetched by spa_try_import() for
spare/cache devices. Import flags are not passed to spa_tryimport(),
which makes it return early due to a missing log device and missing
retrieving the cache device and spare eventually. Passing
ZFS_IMPORT_MISSING_LOG to spa_tryimport() makes it fetch the correct
configuration regardless of the missing log device.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#14794
At our site we have seen cases when multi-modifier protection is enabled
(multihost=on) on our pool and the pool gets suspended due to a single
disk that is failing and responding very slowly. Our pools have 90 disks
in them and we expect disks to fail. The current version of MMP requires
that we wait for other writers before moving on. When a disk is
responding very slowly, we observed that waiting here was bad enough to
cause the pool to suspend. This change allows the MMP thread to bypass
waiting for other threads and reduces the chances the pool gets
suspended.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Herb Wartens <hawartens@gmail.com>
Closes#14659
When testing distributed rebuild performance with more capable
hardware it was observed than increasing the zfs_rebuild_vdev_limit
to 64M reduced the rebuild time by 17%. Beyond 64MB there was
some improvement (~2%) but it was not significant when weighed
against the increased memory usage. Memory usage is capped at 1/4
of arc_c_max.
Additionally, vr_bytes_inflight_max has been moved so it's updated
per-metaslab to allow the size to be adjust while a rebuild is
running.
Reviewed-by: Akash B <akash-b@hpe.com>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#14428
For HDD based pools the default zfs_scan_vdev_limit of 4M
per-vdev can significantly limit the maximum scrub performance.
Increasing the default to 16M can double the scrub speed from
80 MB/s per disk to 160 MB/s per disk.
This does increase the memory footprint during scrub/resilver
but given the performance win this is a reasonable trade off.
Memory usage is capped at 1/4 of arc_c_max. Note that number
of outstanding I/Os has not changed and is still limited by
zfs_vdev_scrub_max_active.
Reviewed-by: Akash B <akash-b@hpe.com>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#14428
When resilvering the estimated time remaining is calculated using
the average issue rate over the current pass. Where the current
pass starts when a scan was started, or restarted, if the pool
was exported/imported.
For dRAID pools in particular this can result in wildly optimistic
estimates since the issue rate will be very high while scanning
when non-degraded regions of the pool are scanned. Once repair
I/O starts being issued performance drops to a realistic number
but the estimated performance is still significantly skewed.
To address this we redefine a pass such that it starts after a
scanning phase completes so the issue rate is more reflective of
recent performance. Additionally, the zfs_scan_report_txgs
module option can be set to reset the pass statistics more often.
Reviewed-by: Akash B <akash-b@hpe.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#14410
Spare vdev should detach from the pool when a disk is reinserted.
However, spare detachment depends on the completion of resilvering,
and if resilver does not schedule, the spare vdev keeps attached to
the pool until the next resilvering. When a zfs pool contains
several disks (25+ mirror), resilvering does not always happen when
a disk is reinserted. In this patch, spare vdev is manually detached
from the pool when resilvering does not occur and it has been tested
on both Linux and FreeBSD.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#14722
After 89cd2197b9 was merged, Clang's
static analyzer began complaining about a dead assignment in
`zfs_fillpage()`. Upon inspection, I noticed that the dead assignment
was because we are not using the calculated io_len that we should use to
avoid asking the DMU to read past the end of a file. This should result
in `dmu_buf_hold_array_by_dnode()` calling `zfs_panic_recover()`.
This issue predates 89cd2197b9, but its
simplification of zfs_fillpage() eliminated the only use of the
assignment to io_len, which made Clang's static analyzer complain about
the issue.
Also, as a precaution, we add an assertion that io_offset < i_size. If
this ever fails, bad things will happen. Otherwise, we are blindly
trusting the kernel not to give us invalid offsets. We continue to
blindly trust it on non-debug kernels.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14534
When a page is faulted in for memory mapped I/O the page lock
may be dropped before it has been read and marked up to date.
If a buffered read encounters such a page in mappedread() it
must wait until the page has been updated. Failure to do so
will result in a panic on debug builds and incorrect data on
production builds.
The critical part of this change is in mappedread() where pages
which are not up to date are now handled. Additionally, it
includes the following simplifications.
- zfs_getpage() and zfs_fillpage() could be passed an array of
pages. This could be more efficient if it was used but in
practice only a single page was ever provided. These
interfaces were simplified to acknowledge that.
- update_pages() was modified to correctly set the PG_error bit
on a page when it cannot be read by dmu_read().
- Setting PG_error and PG_uptodate was moved to zfs_fillpage()
from zpl_readpage_common(). This is consistent with the
handling in update_pages() and mappedread().
- Minor additional refactoring to comments and variable
declarations to improve readability.
- Add a test case to exercise concurrent buffered, direct,
and mmap IO to the same file.
- Reduce the mmap_sync test case default run time.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13608Closes#14498
This had always worked in my testing, but a user on hardware reported
this to happen 100%, and I reproduced it once with cold VM host caches.
dracut-zfs-generator runs as a systemd generator, i.e. at Some
Relatively Early Time; if root= is a fixed dataset, it tries to
"solve [necessities] statically at generation time".
If by that point zfs-import.target hasn't popped (because the import is
taking a non-negligible amount of time for whatever reason), it'll see
no children for the root datase, and as such generate no mounts.
This has never had any right to work. No-one caught this earlier because
it's just that much more convenient to have root=zfs:AUTO, which orders
itself properly.
To fix this, always run zfs-nonroot-necessities.service;
this additionally simplifies the implementation by:
* making BOOTFS from zfs-env-bootfs.service be the real, canonical,
root dataset name, not just "whatever the first bootfs is",
and only set it if we're ZFS-booting
* zfs-{rollback,snapshot}-bootfs.service can use this instead of
re-implementing it
* having zfs-env-bootfs.service also set BOOTFSFLAGS
* this means the sysroot.mount drop-in can be fixed text
* zfs-nonroot-necessities.service can also be constant and always
enabled, because it's conditioned on BOOTFS being set
There is no longer any code generated at run-time
(the sysroot.mount drop-in is an unavoidable gratuitous cp).
The flow of BOOTFS{,FLAGS} from zfs-env-bootfs.service to sysroot.mount
is not noted explicitly in dracut.zfs(7), because (a) at some point it's
just visual noise and (b) it's already ordered via d-p-m.s from z-i.t.
Backport-of: 3399a30ee0
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Deprecation of Python versions below 3.6 gives opportunity to unify the
build and install requirements for OpenZFS packages. The minimal
supported Python version is 3.6 as this is the most recent Python
package CentOS/RHEL 7 users can get.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Rich Ercolani <rincebrain@gmail.com>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: szubersk <szuberskidamian@gmail.com>
Closes#12925
Modify bio_set_flush() so if kernel version is >= 4.10, flags
REQ_PREFLUSH and REQ_OP_WRITE are set together.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Youzhong Yang <yyang@mathworks.com>
Closes#14695
Running `zfs list -o avail rpool` resulted in a core dump.
This commit will fix this.
Run the needed overhead only, when `use_color()` is true.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Wilson <gwilson@delphix.com>
Signed-off-by: Tino Reichardt <milky-zfs@mcmilk.de>
Closes#14712
Add a -K option to the test suite to log each test name to /dev/kmsg
(on Linux), so if there's a kernel warning we'll be able to match
it up to a particular test.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes #13227
- Kmemleak `clear` is invoked right before every test case run.
- Kmemleak `scan` is requested right after each test case is finished.
- Kmemleak instrumentation is not used for
setup/cleanup/pretest/posttest/failsafe stages to shorten the test
case execution time.
- Kmemleak periodic scan is disabled (`scan=0`) before the test suite
run to avoid interfering with the on-demand scan results.
- There are unavoidable potential false positives coming from kernel
areas other than OpenZFS module.
- The ZTS with kmemleak enabled duration is increased by ~50%.
Example run
```
Running Time: 07:12:13
Percent passed: 98.3%
unreferenced object 0xffff9da82aea5410 (size 80):
comm "kworker/u32:10", pid 942206, jiffies 4296749716 (age 2615.516s)
hex dump (first 32 bytes):
00 30 30 00 00 00 00 00 ff 8f 30 00 00 00 00 00 .00.......0.....
51 e6 77 05 a8 9d ff ff 00 00 00 00 00 00 00 00 Q.w.............
backtrace:
[<000000005cf1fea2>] alloc_extent_state+0x1d/0xb0 [btrfs]
[<0000000083f78ae5>] set_extent_bit+0x2ff/0x670 [btrfs]
[<00000000de29249e>] lock_extent_bits+0x6b/0xa0 [btrfs]
[<00000000b241f424>] lock_and_cleanup_extent_if_need+0xaf/0x1c0
[btrfs]
[<0000000093ca72b5>] btrfs_buffered_write+0x297/0x7d0 [btrfs]
[<000000002c2938c8>] btrfs_file_write_iter+0x127/0x390 [btrfs]
[<00000000b888f720>] do_iter_readv_writev+0x152/0x1b0
[<00000000320f0bcc>] do_iter_write+0x7c/0x1c0
[<000000000b5a8fe0>] lo_write_bvec+0x62/0x150 [loop]
[<000000009aa03c73>] loop_process_work+0x250/0xbd0 [loop]
[<00000000c7487d8a>] process_one_work+0x1f1/0x390
[<000000000b236831>] worker_thread+0x53/0x3e0
[<0000000023cb3e57>] kthread+0x127/0x150
[<000000002d48676a>] ret_from_fork+0x22/0x30
```
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: szubersk <szuberskidamian@gmail.com>
Closes#13084
Update the META file to reflect compatibility with the 6.2 kernel.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#14689
After commit 19d3961, progress reporting (-v) with replication flag
enabled does not report the progress on the console. This commit
fixes the issue by updating the logic to check for pa->progress
instead of pa_verbosity in send_progress_thread().
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#14448
This allows parsing of zfs send progress by checking the process
title.
Doing so requires some changes to the send code in libzfs_sendrecv.c;
primarily these changes move some of the accounting around, to allow
for the code to be verbose as normal, or set the process title. Unlike
BSD, setproctitle() isn't standard in Linux; thus, borrowed it from
libbsd with slight modifications.
Authored-by: Sean Eric Fagan <sef@FreeBSD.org>
Co-authored-by: Ryan Moeller <ryan@iXsystems.com>
Co-authored-by: Ameer Hamza <ahamza@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#14376
Holding the zp->z_rangelock as a RL_READER over the range
0-UINT64_MAX is sufficient to prevent the dnode from being
re-dirtied by concurrent writers. To avoid potentially
looping multiple times for external caller which do not
take the rangelock holes are not reported after the first
sync. While not optimal this is always functionally correct.
This change adds the missing rangelock calls on FreeBSD to
zvol_cdev_ioctl().
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#14512Closes#14641
Use a bold header row and colorize the AVAIL column based on
the used space percentage of volume.
We define these colors:
- when > 80%, use yellow
- when > 90%, use red
Reviewed-by: WHR <msl0000023508@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ethan Coe-Renner <coerenner1@llnl.gov>
Signed-off-by: Tino Reichardt <milky-zfs@mcmilk.de>
Closes#14621Closes#14350
Use a bold header and colorize the space suffixes in iostat
by order of magnitude like this:
- K is green
- M is yellow
- G is red
- T is lightblue
- P is magenta
- E is cyan
- 0 space is colored gray
Reviewed-by: WHR <msl0000023508@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ethan Coe-Renner <coerenner1@llnl.gov>
Signed-off-by: Tino Reichardt <milky-zfs@mcmilk.de>
Closes#14621Closes#14459
Linux 6.3+, and backports from it (6.2.8+), changed the
signatures on bdev_io_{start,end}_acct. Add a case for it.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#14658Closes#14668
zfsd fetches new pool configuration through ZFS_IOC_POOL_STATS but
it does not get updated nvlist configuration for spare vdev since
the configuration is read by spa_spares->sav_config. In this commit,
updating the vdev state for spare vdev that is consumed by zfsd on
spare disk hotplug.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#14653
This commit supports for spare vdev hotplug. The
spare vdev associated with all the pools will be
marked as "Removed" when the drive is physically
detached and will become "Available" when the
drive is reattached. Currently, the spare vdev
status does not change on the drive removal and
the same is the case with reattachment.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#14295
In order for zed to process the removal event correctly,
udev change event needs to be posted to sync the blkid
information. spa_create() and spa_config_update() posts
the event already through spa_write_cachefile(). Doing
the same for spa_vdev_attach() that handles the case
for vdev attachment and replacement.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#14172
ZED does not take any action for disk removal events if there is no
spare VDEV available. Added zpool_vdev_remove_wanted() in libzfs
and vdev_remove_wanted() in vdev.c to remove the VDEV through ZED
on removal event. This means that if you are running zed and
remove a disk, it will be propertly marked as REMOVED.
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Remove arc_reduce_target_size() call from arc_prune_task(). The idea
of arc_prune_task() is to remove external references on ARC metadata,
such as vnodes. Since arc_prune_async() is called only from ARC itself,
it makes no sense to create a parasitic loop between ARC eviction and
the pruning, treatening to drop ARC to its minimum. I can't guess why
it was added as part of FreeBSD to OpenZFS integration.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14639
Debugging reported NULL de-reference panic in dnode_hold_impl() I found
that for certain types of errors arc_read() may only return error code,
but not properly report it via done and pio arguments. Lack of done
calls may result in reference and/or memory leaks in higher level code.
Lack of error reporting via pio may result in unnoticed errors there.
For example, dbuf_read(), where dbuf_read_impl() ignores arc_read()
return, relies completely on the pio mechanism and missed the errors.
This patch makes arc_read() to always call done callback and always
propagate errors to parent zio, if either is provided.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
CpaDcRqResults have to be initialized with checksum=1 for adler32.
Otherwise when error CPA_DC_OVERFLOW occurred, the next compress
operation will continue on previously part-compressed data, and write
invalid checksum data. When zfs decompress the compressed data, a
invalid checksum will occurred and lead to #14463
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Weigang Li <weigang.li@intel.com>
Reviewed-by: Chengfei Zhu <chengfeix.zhu@intel.com>
Signed-off-by: naivekun <naivekun0817@gmail.com>
Closes#14632Closes#14463
`lseek(SEEK_DATA | SEEK_HOLE)` are only accurate when the on-disk blocks
reflect all writes, i.e. when there are no dirty data blocks. To ensure
this, if the target dnode is dirty, they wait for the open txg to be
synced, so we can call them "stabilizing operations". If they cause
txg_wait_synced often, it can be detrimental to performance.
Typically, a group of files are all modified, and then SEEK_DATA/HOLE
are performed on them. In this case, the first SEEK does a
txg_wait_synced(), and subsequent SEEKs don't need to wait, so
performance is good.
However, if a workload involves an interleaved metadata modification,
the subsequent SEEK may do a txg_wait_synced() unnecessarily. For
example, if we do a `read()` syscall to each file before we do its SEEK.
This applies even with `relatime=on`, when the `read()` is the first
read after the last write. The txg_wait_synced() is unnecessary because
the SEEK operations only care that the structure of the tree of indirect
and data blocks is up to date on disk. They don't care about metadata
like the contents of the bonus or spill blocks. (They also don't care
if an existing data block is modified, but this would be more involved
to filter out.)
This commit changes the behavior of SEEK_DATA/HOLE operations such that
they do not call txg_wait_synced() if there is only a pending change to
the bonus or spill block.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#13368
Issue #14594
Issue #14512
Issue #14009
Update the GitHub actions workflows using a subset of the changes
from the master branch, commit 620a977f22. Cherry-picking each
relevant commit would have resulted in a large number of conflicts
so this change only applies a minimal set of useful updates.
- Added build-dependencies.txt and checkstyle-dependencies.txt
- Added reclaim_disk_space.sh script
- Minor changes to build steps
- Reduced ztest run time
- checkbashisms, mandoc, and cppcheck were not included to
avoid additional backports
- Add exceptions for shellcheck
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
- GitHub workflows are run on Ubuntu 22.04
- Extract the `checkstyle` workflow dependencies to a separate file.
- Refresh the `build-dependencies.txt` list.
Notes: Partial check pick of 9e7fc5da38. This change does not
include the build-dependencies.txt or checkstyle-dependencies.txt
changes.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: szubersk <szuberskidamian@gmail.com>
Closes#14148
When using the zfs initramfs scripts on my system, I get various
errors at initramfs stage, such as:
cannot open '-o': name must begin with a letter
My zfs binaries are compiled with musl libc, which may be why
this happens. In any case, fix the argument order to make the
zpool binary happy, and to match its --help output.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Daniel Kolesa <daniel@octaforge.org>
Closes#14572
The default_bs and default_ibs tunables control the default block size
and indirect block size.
So far, default_bs and default_ibs were tunable only on FreeBSD, e.g.,
sysctl vfs.zfs.default_ibs
Remove the FreeBSD-specific sysctl code and expose default_bs and
default_ibs as tunables on both Linux and FreeBSD using
ZFS_MODULE_PARAM.
One of the use cases for changing the values of those tunables is to
lower the indirect block size, which may improve performance of large
directories (as discussed during the OpenZFS Leadership Meeting
on 2022-08-16).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Mateusz Piotrowski <mateusz.piotrowski@klarasystems.com>
Sponsored-by: Wasabi Technology, Inc.
Closes#14293
dc5c8006f6 was recently merged to prefetch
up to 128 deadlists. Unfortunately, a loop was missing an increment,
such that it will prefetch all deadlists. The performance properties of
that patch probably should be re-evaluated.
This was caught by CodeQL's cpp/constant-comparison check in an
experimental branch where I am testing the security-and-extended
queries. It complained about the `i < 128` part of the loop condition
always evaluating to the same thing. The standard CodeQL configuration
we use missed this because it does not include that check.
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14573
by placing the most common use case (no special vdevs) first and avoid
allocating new variables.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#14494Closes#14563
With some pathological access patterns it is possible to make ZFS
accumulate almost unlimited amount of speculative prefetch ZIOs.
Combined with linear ABD allocations in RAIDZ code, it appears to
be possible to exhaust system KVA, triggering kernel panic.
Address this by introducing a system-wide counter of active prefetch
requests and blocking prefetch distance doubling per stream hits if
the number of active requests is higher that ~6% of ARC size.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14516
During snapshot deletion ZFS may issue several reads for each deadlist
to merge them into next snapshot's or pool's bpobj. Number of the dead
lists increases with number of snapshots. On HDD pools it may take
significant time during which sync thread is blocked.
This patch introduces prescient prefetch of required blocks for up to
128 deadlists ahead. Tests show reduction of time required to delete
dataset with 720 snapshots with randomly overwritten file on wide HDD
pool from 75-85 to 22-28 seconds.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Issue #14276Closes#14402
Despite all optimizations, tests on actual hardware show that FreeBSD
kernel can't sleep for less then ~2us. Similar tests on Linux show
~50us delay at least from nanosleep() (haven't tested inside kernel).
It means that on very fast log device ZIL may not be able to satisfy
zfs_commit_timeout_pct block commit timeout, increasing log latency
more than desired.
Handle that by introduction of zil_min_commit_timeout parameter,
specifying minimal timeout value where additional delays to aggregate
writes may be skipped. Also skip delays if the LWB is more than 7/8
full, that often happens if I/O sizes are constant and match one of
LWB sizes. Both things are applied only if there were no already
outstanding log blocks, that may indicate single-threaded workload,
that by definition can not benefit from the commit delays.
While there, add short time moving average to zl_last_lwb_latency to
make it more stable.
Tests of single-threaded 4KB writes to NVDIMM SLOG on FreeBSD show IOPS
increase by 9% instead of expected 5%. For zfs_commit_timeout_pct of
1 there IOPS increase by 5.5% instead of expected 1%.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Prakash Surya <prakash.surya@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14418
On FreeBSD this reduces this structure size from 64 to 56 bytes.
dnode_handle_t respectively reduces from 72 to 64 bytes. It sounds
like a waste to need 72 bytes to be able to relocate 808 bytes of
dnode_t, which relocation on FreeBSD is not even supported.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14317
Microzap on-disk format does not include a hash tree, expecting one to
be built in RAM during mzap_open(). The built tree is linked to DMU
user buffer, freed when original DMU buffer is dropped from cache. I've
found that workloads accessing many large directories and having active
eviction from DMU cache spend significant amount of time building and
then destroying the trees. I've also found that for each 64 byte mzap
element additional 64 byte tree element is allocated, that is a waste
of memory and CPU caches.
Improve memory efficiency of the hash tree by switching from AVL-tree
to B-tree. It allows to save 24 bytes per element just on pointers.
Save 32 bits on mze_hash by storing only upper 32 bits since lower 32
bits are always zero for microzaps. Save 16 bits on mze_chunkid, since
microzap can never have so many elements. Respectively with the 16 bits
there can be no more than 16 bits of collision differentiators. As
result, struct mzap_ent now drops from 48 (rounded to 64) to 8 bytes.
Tune B-trees for small data. Reduce BTREE_CORE_ELEMS from 128 to 126
to allow struct zfs_btree_core in case of 8 byte elements to pack into
2KB instead of 4KB. Aside of the microzaps it should also help 32bit
range trees. Allow custom B-tree leaf size to reduce memmove() time.
Split zap_name_alloc() into zap_name_alloc() and zap_name_init_str().
It allows to not waste time allocating/freeing memory when processing
multiple names in a loop during mzap_open().
Together on a pool with 10K directories of 1800 files each and DMU
cache limited to 128MB this reduces time of `find . -name zzz` by 41%
from 7.63s to 4.47s, and saves additional ~30% of CPU time on the DMU
cache reclamation.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14039
(cherry picked from commit 9dcdee7889)
Add config support for openEuler, so that it set the right sysconfig
dir for openEuler.
And DEFAULT_INIT_SCRIPT is no longer needed since commit "2a34db1bd
Base init scripts for SYSV systems".
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Xinliang Liu <xinliang.liu@linaro.org>
Closes#14241
Gentoo and Alpine always set the rc init scripts' shebang to
#!/sbin/openrc-run, whether or not openrc is installed.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Peter Levine <plevine457@gmail.com>
Closes#12683Closes#12692
OpenEuler uses the same package manager DNF as RHEL/Fedora. And
it is similar to RHEL/Fedora.
OpenEuler Linux is becoming the mainstream Linux distro in China.
So adding support for it makes sense for the users. For more
details about it see: https://www.openeuler.org/en/.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Damian Szuberski <szuberskidamian@gmail.com>
Signed-off-by: Xinliang Liu <xinliang.liu@linaro.org>
Closes#14222
Conflicts:
rpm/generic/zfs.spec.in
The zio returned from arc_write() in dmu_objset_sync() uses
zio_nowait(). However we may reach the end of dsl_dataset_sync()
which checks if we need to activate features in the filesystem
without knowing if that zio has even run through the ZIO pipeline yet.
In that case we will flag features to be activated in
dsl_dataset_block_born() but dsl_dataset_sync() has already
completed its run and those features will not actually be activated.
Mitigate this by moving the feature activation code in
dsl_dataset_sync_done(). Also add new ASSERTs in
dsl_scan_visitbp() checking if a block contradicts any filesystem
flags.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#13816
In initramfs, mount.zfs fails to mount a dataset with mountpoint=none,
but mount.zfs -o zfsutil works. Use -o zfsutil when mountpoint=none.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#14455
(cherry picked from commit eb823cbc76)
When mounting the root filesystem, vfs_t->mnt_vnodecovered is null
This will cause zfsctl_is_node() to dereference a null pointer when
mounting, or updating the mount flags, on the root filesystem, both
of which happen during the boot process.
Reported-by: Martin Matuska <mm@FreeBSD.org>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Closes#14218
Rather than doing a terrible credential swapping hack, we just
check that the thing being mounted is a snapshot, and the mountpoint
is the zfsctl directory, then we allow it.
If the mount attempt is from inside a jail, on an unjailed dataset
(mounted from the host, not by the jail), the ability to mount the
snapshot is controlled by a new per-jail parameter: zfs.mount_snapshot
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Sponsored-by: Modirum MDPay
Sponsored-by: Klara Inc.
Closes#13758
Linux 6.2 changes the second argument of the set_acl operation to be a
"struct dentry *" rather than a "struct inode *". The inode* parameter
is still available as dentry->d_inode, so adjust the call to the _impl
function call to dereference and pass that pointer to it.
Also document that the get_acl -> get_inode_acl member name change from
commit 884a693 was an API change also introduced in Linux 6.2.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#14415
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.