If libselinux is detected on your system at configure time link
against it. This allows us to use a library call to detect if
selinux is enabled and if it is to pass the mount option:
"context=\"system_u:object_r:file_t:s0"
For now this is required because none of the existing selinux
policies are aware of the zfs filesystem type. Because of this
they do not properly enable xattr based labeling even though
zfs supports all of the required hooks.
Until distro's add zfs as a known xattr friendly fs type we
must use mntpoint labeling. Alternately, end users could modify
their existing selinux policy with a little guidance.
For while now mkdirp has been built as part of libspl however
the protoype was never added to libgen.h. This went unnoticed
until enabling the mount support which uses mkdirp().
Specifically, this fixes the two following errors in zdb when a pool
is composed of block devices:
1) 'Value too large for defined data type' when running 'zdb <dataset>'.
2) 'character device required' when running 'zdb -l <block-device>'.
Signed-off-by: Ricardo M. Correia <ricardo.correia@oracle.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
This commit fixes a sign extension bug affecting l2arc devices. Extremely
large offsets may be passed down to the low level block device driver on
reads, generating errors similar to
attempt to access beyond end of device
sdbi1: rw=14, want=36028797014862705, limit=125026959
The unwanted sign extension occurrs because the function arc_read_nolock()
stores the offset as a daddr_t, a 32-bit signed int type in the Linux kernel.
This offset is then passed to zio_read_phys() as a uint64_t argument, causing
sign extension for values of 0x80000000 or greater. To avoid this, we store
the offset in a uint64_t.
This change also changes a few daddr_t struct members to uint64_t in the libspl
headers to avoid similar bugs cropping up in the future. We also add an ASSERT
to __vdev_disk_physio() to check for invalid offsets.
Closes#66
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
ZFS works best when it is notified as soon as possible when a device
failure occurs. This allows it to immediately start any recovery
actions which may be needed. In theory Linux supports a flag which
can be set on bio's called FAILFAST which provides this quick
notification by disabling the retry logic in the lower scsi layers.
That's the theory at least. In practice is turns out that while the
flag exists you oddly have to set it with the BIO_RW_AHEAD flag.
And even when it's set it you may get retries in the low level
drivers decides that's the right behavior, or if you don't get the
right error codes reported to the scsi midlayer.
Unfortunately, without additional kernels patchs there's not much
which can be done to improve this. Basically, this just means that
it may take 2-3 minutes before a ZFS is notified properly that a
device has failed. This can be improved and I suspect I'll be
submitting patches upstream to handle this.
The zfs package supports the option --with-config=srpm which
is used to bootstrap configure to allow the 'make srpm' target
to work. This has the advantage of allowing creation of source
rpms without having all your -devel packages installed. This
source package can then be feed back in to an automated build
farm which only installs the required packages listed by the
srpm. This ensures that all proper dependencies are expressed
by the source package, because if they are not you will get
configure/build failures.
The trouble here is that --with-config=srpm prevents the
architecture check from running resulting in TARGET_ASM_DIR
being set to the default asm-generic. The 'make dist' rule
then fails because there is no asm-generic/atomic.S file
because it is generated at build time. To handle this I
have added an empty file asm-generic/atomic.S simply as a
place holder for 'make dist'.
One of the neat tricks an autoconf style project is capable of
is allow configurion/building in a directory other than the
source directory. The major advantage to this is that you can
build the project various different ways while making changes
in a single source tree.
For example, this project is designed to work on various different
Linux distributions each of which work slightly differently. This
means that changes need to verified on each of those supported
distributions perferably before the change is committed to the
public git repo.
Using nfs and custom build directories makes this much easier.
I now have a single source tree in nfs mounted on several different
systems each running a supported distribution. When I make a
change to the source base I suspect may break things I can
concurrently build from the same source on all the systems each
in their own subdirectory.
wget -c http://github.com/downloads/behlendorf/zfs/zfs-x.y.z.tar.gz
tar -xzf zfs-x.y.z.tar.gz
cd zfs-x-y-z
------------------------- run concurrently ----------------------
<ubuntu system> <fedora system> <debian system> <rhel6 system>
mkdir ubuntu mkdir fedora mkdir debian mkdir rhel6
cd ubuntu cd fedora cd debian cd rhel6
../configure ../configure ../configure ../configure
make make make make
make check make check make check make check
This change also moves many of the include headers from individual
incude/sys directories under the modules directory in to a single
top level include directory. This has the advantage of making
the build rules cleaner and logically it makes a bit more sense.
Add the initial products from autogen.sh. These products will
be updated incrementally after this point as development occurs.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
All changes needed for the libspl layer. This includes modifications
to files directly copied from OpenSolaris and the addition of new
files needed to fill in the gaps.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
