This changes taskq_thread_should_stop() to limit maximum exit rate
for idle threads to one per 5 seconds. I believe the previous one
was broken, not allowing any thread exits for tasks arriving more
than one at a time and so completing while others are running.
Also while there:
- Remove taskq_thread_spawn() calls on task allocation errors.
- Remove extra taskq_thread_should_stop() call.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Rich Ercolani <rincebrain@gmail.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#15873
... by checking that previous block is fully written and flushed.
It allows to skip commit delays since we can give up on aggregation
in that case. This removes zil_min_commit_timeout parameter, since
for single-threaded workloads it is not needed at all, while on very
fast devices even some multi-threaded workloads may get detected as
single-threaded and still bypass the wait. To give multi-threaded
workloads more aggregation chances increase zfs_commit_timeout_pct
from 5 to 10%, as they should suffer less from additional latency.
Also single-threaded workloads detection allows in perspective better
prediction of the next block size.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Prakash Surya <prakash.surya@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#15381
Currently, zvol uses a single taskq, resulting in throughput bottleneck
under heavy load due to lock contention on the single taskq. This patch
addresses the performance bottleneck under heavy load conditions by
utilizing multiple taskqs, thus mitigating lock contention. The number
of taskqs scale dynamically based on the available CPUs in the system,
as illustrated below:
taskq total
cpus taskqs threads threads
------- ------- ------- -------
1 1 32 32
2 1 32 32
4 1 32 32
8 2 16 32
16 3 11 33
32 5 7 35
64 8 8 64
128 11 12 132
256 16 16 256
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#15992
We don't want to change to brand-new code in the middle of a stable
series, but we want it available to test for people running into page
splitting issues.
This commits make zfs_vdev_disk_classic=1 the default, and updates the
documentation to better explain what's going on.
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Sponsored-by: Klara, Inc.
Sponsored-by: Wasabi Technology, Inc.
This makes the submission method selectable at module load time via the
`zfs_vdev_disk_classic` parameter, allowing this change to be backported
to 2.2 safely, and disabled in favour of the "classic" submission method
if new problems come up.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Sponsored-by: Klara, Inc.
Sponsored-by: Wasabi Technology, Inc.
Closes#15533Closes#15588
(cherry picked from commit df2169d141)
This commit tackles a number of issues in the way BIOs (`struct bio`)
are constructed for submission to the Linux block layer.
The kernel has a hard upper limit on the number of pages/segments that
can be added to a BIO, as well as a separate limit for each device
(related to its queue depth and other scheduling characteristics).
ZFS counts the number of memory pages in the request ABD
(`abd_nr_pages_off()`, and then uses that as the number of segments to
put into the BIO, up to the hard upper limit. If it requires more than
the limit, it will create multiple BIOs.
Leaving aside the fact that page count method is wrong (see below), not
limiting to the device segment max means that the device driver will
need to split the BIO in half. This is alone is not necessarily a
problem, but it interacts with another issue to cause a much larger
problem.
The kernel function to add a segment to a BIO (`bio_add_page()`) takes a
`struct page` pointer, and offset+len within it. `struct page` can
represent a run of contiguous memory pages (known as a "compound page").
In can be of arbitrary length.
The ZFS functions that count ABD pages and load them into the BIO
(`abd_nr_pages_off()`, `bio_map()` and `abd_bio_map_off()`) will never
consider a page to be more than `PAGE_SIZE` (4K), even if the `struct
page` is for multiple pages. In this case, it will load the same `struct
page` into the BIO multiple times, with the offset adjusted each time.
With a sufficiently large ABD, this can easily lead to the BIO being
entirely filled much earlier than it could have been. This is also
further contributes to the problem caused by the incorrect segment limit
calculation, as its much easier to go past the device limit, and so
require a split.
Again, this is not a problem on its own.
The logic for "never submit more than `PAGE_SIZE`" is actually a little
more subtle. It will actually never submit a buffer that crosses a 4K
page boundary.
In practice, this is fine, as most ABDs are scattered, that is a list of
complete 4K pages, and so are loaded in as such.
Linear ABDs are typically allocated from slabs, and for small sizes they
are frequently not aligned to page boundaries. For example, a 12K
allocation can span four pages, eg:
-- 4K -- -- 4K -- -- 4K -- -- 4K --
| | | | |
:## ######## ######## ######: [1K, 4K, 4K, 3K]
Such an allocation would be loaded into a BIO as you see:
[1K, 4K, 4K, 3K]
This tends not to be a problem in practice, because even if the BIO were
filled and needed to be split, each half would still have either a start
or end aligned to the logical block size of the device (assuming 4K at
least).
---
In ideal circumstances, these shortcomings don't cause any particular
problems. Its when they start to interact with other ZFS features that
things get interesting.
Aggregation will create a "gang" ABD, which is simply a list of other
ABDs. Iterating over a gang ABD is just iterating over each ABD within
it in turn.
Because the segments are simply loaded in order, we can end up with
uneven segments either side of the "gap" between the two ABDs. For
example, two 12K ABDs might be aggregated and then loaded as:
[1K, 4K, 4K, 3K, 2K, 4K, 4K, 2K]
Should a split occur, each individual BIO can end up either having an
start or end offset that is not aligned to the logical block size, which
some drivers (eg SCSI) will reject. However, this tends not to happen
because the default aggregation limit usually keeps the BIO small enough
to not require more than one split, and most pages are actually full 4K
pages, so hitting an uneven gap is very rare anyway.
If the pool is under particular memory pressure, then an IO can be
broken down into a "gang block", a 512-byte block composed of a header
and up to three block pointers. Each points to a fragment of the
original write, or in turn, another gang block, breaking the original
data up over and over until space can be found in the pool for each of
them.
Each gang header is a separate 512-byte memory allocation from a slab,
that needs to be written down to disk. When the gang header is added to
the BIO, its a single 512-byte segment.
Pulling all this together, consider a large aggregated write of gang
blocks. This results a BIO containing lots of 512-byte segments. Given
our tendency to overfill the BIO, a split is likely, and most possible
split points will yield a pair of BIOs that are misaligned. Drivers that
care, like the SCSI driver, will reject them.
---
This commit is a substantial refactor and rewrite of much of `vdev_disk`
to sort all this out.
`vdev_bio_max_segs()` now returns the ideal maximum size for the device,
if available. There's also a tuneable `zfs_vdev_disk_max_segs` to
override this, to assist with testing.
We scan the ABD up front to count the number of pages within it, and to
confirm that if we submitted all those pages to one or more BIOs, it
could be split at any point with creating a misaligned BIO. If the
pages in the BIO are not usable (as in any of the above situations), the
ABD is linearised, and then checked again. This is the same technique
used in `vdev_geom` on FreeBSD, adjusted for Linux's variable page size
and allocator quirks.
`vbio_t` is a cleanup and enhancement of the old `dio_request_t`. The
idea is simply that it can hold all the state needed to create, submit
and return multiple BIOs, including all the refcounts, the ABD copy if
it was needed, and so on. Apart from what I hope is a clearer interface,
the major difference is that because we know how many BIOs we'll need up
front, we don't need the old overflow logic that would grow the BIO
array, throw away all the old work and restart. We can get it right from
the start.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Sponsored-by: Klara, Inc.
Sponsored-by: Wasabi Technology, Inc.
Closes#15533Closes#15588
(cherry picked from commit 06a196020e)
Because "filesystem" and "volume" are just too long!
Sponsored-by: https://despairlabs.com/sponsor/
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <robn@despairlabs.com>
Closes#15864
(cherry picked from commit a5a725440b)
When very large pools are present, it can be laborious to find
reasons for why a pool is degraded and/or where an unhealthy vdev
is. This option filters out vdevs that are ONLINE and with no errors
to make it easier to see where the issues are. Root and parents of
unhealthy vdevs will always be printed.
Testing:
ZFS errors and drive failures for multiple vdevs were simulated with
zinject.
Sample vdev listings with '-e' option
- All vdevs healthy
NAME STATE READ WRITE CKSUM
iron5 ONLINE 0 0 0
- ZFS errors
NAME STATE READ WRITE CKSUM
iron5 ONLINE 0 0 0
raidz2-5 ONLINE 1 0 0
L23 ONLINE 1 0 0
L24 ONLINE 1 0 0
L37 ONLINE 1 0 0
- Vdev faulted
NAME STATE READ WRITE CKSUM
iron5 DEGRADED 0 0 0
raidz2-6 DEGRADED 0 0 0
L67 FAULTED 0 0 0 too many errors
- Vdev faults and data errors
NAME STATE READ WRITE CKSUM
iron5 DEGRADED 0 0 0
raidz2-1 DEGRADED 0 0 0
L2 FAULTED 0 0 0 too many errors
raidz2-5 ONLINE 1 0 0
L23 ONLINE 1 0 0
L24 ONLINE 1 0 0
L37 ONLINE 1 0 0
raidz2-6 DEGRADED 0 0 0
L67 FAULTED 0 0 0 too many errors
- Vdev missing
NAME STATE READ WRITE CKSUM
iron5 DEGRADED 0 0 0
raidz2-6 DEGRADED 0 0 0
L67 UNAVAIL 3 1 0
- Slow devices when -s provided with -e
NAME STATE READ WRITE CKSUM SLOW
iron5 DEGRADED 0 0 0 -
raidz2-5 DEGRADED 0 0 0 -
L10 FAULTED 0 0 0 0 external device fault
L51 ONLINE 0 0 0 14
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Cameron Harr <harr1@llnl.gov>
Closes#15769
On Linux the ioctl_ficlonerange() and ioctl_ficlone() system calls
are expected to either fully clone the specified range or return an
error. The range may be for an entire file. While internally ZFS
supports cloning partial ranges there's no way to return the length
cloned to the caller so we need to make this all or nothing.
As part of this change support for the REMAP_FILE_CAN_SHORTEN flag
has been added. When REMAP_FILE_CAN_SHORTEN is set zfs_clone_range()
will return a shortened range when encountering pending dirty records.
When it's clear zfs_clone_range() will block and wait for the records
to be written out allowing the blocks to be cloned.
Furthermore, the file range lock is held over the region being cloned
to prevent it from being modified while cloning. This doesn't quite
provide an atomic semantics since if an error is encountered only a
portion of the range may be cloned. This will be converted to an
error if REMAP_FILE_CAN_SHORTEN was not provided and returned to the
caller. However, the destination file range is left in an undefined
state.
A test case has been added which exercises this functionality by
verifying that `cp --reflink=never|auto|always` works correctly.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#15728Closes#15842
Add `zpool` flags to control the slot power to drives. This assumes
your SAS or NVMe enclosure supports slot power control via sysfs.
The new `--power` flag is added to `zpool offline|online|clear`:
zpool offline --power <pool> <device> Turn off device slot power
zpool online --power <pool> <device> Turn on device slot power
zpool clear --power <pool> [device] Turn on device slot power
If the ZPOOL_AUTO_POWER_ON_SLOT env var is set, then the '--power'
option is automatically implied for `zpool online` and `zpool clear`
and does not need to be passed.
zpool status also gets a --power option to print the slot power status.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mart Frauenlob <AllKind@fastest.cc>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#15662
zpool-iostat.8: Updated time(2) -> time(1) to align to manual page
zpool-list.8: Updated time(2) -> time(1) to align to manual page
zpool-status.8: Updated time(2) -> time(1) to align to manual page
zpool-wait.8: Update time(2) -> time(1) to align to manual page
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Christopher Davidson <christopher.davidson@gmail.com>
Closes#15823
When two datasets share the same master encryption key, it is safe
to clone encrypted blocks. Currently only snapshots and clones
of a dataset share with it the same encryption key.
Added a test for:
- Clone from encrypted sibling to encrypted sibling with
non encrypted parent
- Clone from encrypted parent to inherited encrypted child
- Clone from child to sibling with encrypted parent
- Clone from snapshot to the original datasets
- Clone from foreign snapshot to a foreign dataset
- Cloning from non-encrypted to encrypted datasets
- Cloning from encrypted to non-encrypted datasets
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Original-patch-by: Pawel Jakub Dawidek <pawel@dawidek.net>
Signed-off-by: Kay Pedersen <mail@mkwg.de>
Closes#15544
It is unused for 3 years since #10576.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#15507
We are finding that as customers get larger and faster machines
(hundreds of cores, large NVMe-backed pools) they keep hitting
relatively low performance ceilings. Our profiling work almost always
finds that they're running into bottlenecks on the SPA IO taskqs.
Unfortunately there's often little we can advise at that point, because
there's very few ways to change behaviour without patching.
This commit adds two load-time parameters `zio_taskq_read` and
`zio_taskq_write` that can configure the READ and WRITE IO taskqs
directly.
This achieves two goals: it gives operators (and those that support
them) a way to tune things without requiring a custom build of OpenZFS,
which is often not possible, and it lets us easily try different config
variations in a variety of environments to inform the development of
better defaults for these kind of systems.
Because tuning the IO taskqs really requires a fairly deep understanding
of how IO in ZFS works, and generally isn't needed without a pretty
serious workload and an ability to identify bottlenecks, only minimal
documentation is provided. Its expected that anyone using this is going
to have the source code there as well.
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Sponsored-by: Klara, Inc.
Sponsored-by: Wasabi Technology, Inc.
Same idea as the dedup stats, but for block cloning.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Kay Pedersen <mail@mkwg.de>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <robn@despairlabs.com>
Closes#15541
Copy the disable parameter that FreeBSD implemented, and extend it to
work on Linux as well, until we're sure this is stable.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#15529
This commit updates zpool-features.7 man page to add newly added
zpool features to grub2 compatibility list.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Umer Saleem <usaleem@ixsystems.com>
Closes#15505
This reverts commit aefb6a2bd6.
aefb6a2bd temporally disabled blk-mq until we could fix a fix for
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#15439
Have libzfs call a special `zfs_prepare_disk` script before a disk is
included into the pool. The user can edit this script to add things
like a disk firmware update or a disk health check. Use of the script
is totally optional. See the zfs_prepare_disk manpage for full details.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#15243
For synchronous write workloads with large IO sizes, a pool configured
with a slog performs worse than one with an embedded zil:
sequential_writes 1m sync ios, 16 threads
Write IOPS: 1292 438 -66.10%
Write Bandwidth: 1323570 448910 -66.08%
Write Latency: 12128400 36330970 3.0x
sequential_writes 1m sync ios, 32 threads
Write IOPS: 1293 430 -66.74%
Write Bandwidth: 1324184 441188 -66.68%
Write Latency: 24486278 74028536 3.0x
The reason is the `zil_slog_bulk` variable. In `zil_lwb_write_open`,
if a zil block is greater than 768K, the priority of the write is
downgraded from sync to async. Increasing the value allows greater
throughput. To select a value for this PR, I ran an fio workload with
the following values for `zil_slog_bulk`:
zil_slog_bulk KiB/s
1048576 422132
2097152 478935
4194304 533645
8388608 623031
12582912 827158
16777216 1038359
25165824 1142210
33554432 1211472
50331648 1292847
67108864 1308506
100663296 1306821
134217728 1304998
At 64M, the results with a slog are now improved to parity with an
embedded zil:
sequential_writes 1m sync ios, 16 threads
Write IOPS: 438 1288 2.9x
Write Bandwidth: 448910 1319062 2.9x
Write Latency: 36330970 12163408 -66.52%
sequential_writes 1m sync ios, 32 threads
Write IOPS: 430 1290 3.0x
Write Bandwidth: 441188 1321693 3.0x
Write Latency: 74028536 24519698 -66.88%
None of the other tests in the performance suite (run with a zil or
slog) had a significant change, including the random_write_zil tests,
which use multiple datasets.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: John Wren Kennedy <john.kennedy@delphix.com>
Closes#14378
There was a report of zvol data loss (#15351) after enabling blk-mq on a
zvol backed with 16k physical block sized disks. Out of an abundance of
caution, do not allow the user to enable blk-mq until we can look into
the issue.
Note that blk-mq was not enabled by default on zvols. It was always
opt-in via the zvol_use_blk_mq module parameter.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Addresses: #15351Closes#15378
Benchmarks show that at certain write sizes range lock/unlock take
not so much time as extra memory copy. The exact threshold is not
obvious due to other overheads, but it is definitely lower than
~63KB used before. Make it configurable, defaulting at 7.5KB,
that is 8KB of nearest malloc() size minus itx and lr structs.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#15353
Here I'm trying to succinctly introduce the concept, the basics of its
construction, how its different to dedup, how to use it, and where its
limitations lie, in four paragraphs and with enough searchable terms to
help the reader find more information both within OpenZFS and elsewhere.
Phew.
Sponsored-By: Klara, Inc.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Closes#15362
Before this change ZFS created threads for 50% of CPUs for each top-
level vdev. Plus it created the same number of threads for embedded
log groups (that have only one metaslab and don't need any preload).
As result, on system with 80 CPUs and pool of 60 vdevs this resulted
in 4800 metaslab preload threads, that is absolutely insane.
This patch changes the preload threads to 50% of CPUs in one taskq
per pool, so on the mentioned system it will be only 40 threads.
Among other things this fixes zdb on the mentioned system and pool
on FreeBSD, that failed to create so many threads in one process.
Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#15319
This commit adds '-u' flag for zfs set operation. With this flag,
mountpoint, sharenfs and sharesmb properties can be updated
without actually mounting or sharing the dataset.
Previously, if dataset was unmounted, and mountpoint property was
updated, dataset was not mounted after the update. This behavior
is changed in #15240. We mount the dataset whenever mountpoint
property is updated, regardless if it's mounted or not.
To provide the user with option to keep the dataset unmounted and
still update the mountpoint without mounting the dataset, '-u'
flag can be used.
If any of mountpoint, sharenfs or sharesmb properties are updated
with '-u' flag, the property is set to desired value but the
operation to (re/un)mount and/or (re/un)share the dataset is not
performed and dataset remains as it was before.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Umer Saleem <usaleem@ixsystems.com>
Closes#15322
Try to clarify wording to reduce zpool add incidents.
Add an attach example.
Reviewed-by: Rich Ercolani <Rincebrain@gmail.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#15179
- Distribute zfs-[un]jail.8 on FreeBSD and zfs-[un]zone.8 on Linux
- zfsprops.7: mirror zoned/jailed, only available on respective platforms
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#15161
POSIX timers target the process, not the thread (as does SIGINFO),
so we need to block it in the main thread which will die if interrupted.
Ref: https://101010.pl/@ed1conf@bsd.network/110731819189629373
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#15113
metaslab_force_ganging isn't enough to actually force ganging, because
it still only forces 3% of the time. This adds
metaslab_force_ganging_pct so we can configure how often to force
ganging.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Sponsored-by: Klara, Inc.
Sponsored-by: Wasabi Technology, Inc.
Closes#15088
- Reduce maximum prefetch distance for 32bit platforms to 8MB as it
was previously. Those systems didn't grow much probably, so better
stay conservative there.
- Retire array_rd_sz tunable, blocking prefetch for large requests.
We should not penalize applications trying to be more efficient. The
speculative prefetcher by itself has reasonable distance limits, and
1MB is not much at all these days.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#15072
With anything but fletcher-4, even a tiny change in the input will cause
the checksum value to change completely. So knowing the actual and
expected checksums doesn't provide much more information than "they
don't match". The harm in sending them is simply that they bloat the
event. In particular, on FreeBSD the event must fit into a 1016 byte
buffer.
Fixes#14717 for mirrored pools.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Rich Ercolani <rincebrain@gmail.com>
Signed-off-by: Alan Somers <asomers@gmail.com>
Sponsored-by: Axcient
Closes#14717Closes#15052
The checksum histograms were intended to be used with ATA and parallel
SCSI, which are obsolete. With modern storage hardware, they will
almost always look like white noise; all bits will be wrong. They only
serve to bloat the event. That's a particular problem on FreeBSD, where
events must fit into a 1016 byte buffer.
This fixes issue #14717 for RAIDZ pools, but not for mirror pools.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Rich Ercolani <rincebrain@gmail.com>
Signed-off-by: Alan Somers <asomers@gmail.com>
Sponsored-by: Axcient
Closes#15052
The DDT is really inefficient on 4k and up vdevs, because it always
allocates 4k blocks, and while compression could save us somewhat
at ashift 9, that stops being true.
So let's change the default to 32 KiB, which seems like a reasonable
compromise between improved space savings and inflated write sizes
for DDT updates.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#14654
Scan process may skip blocks based on their birth time, DVA, etc.
Traditionally those blocks were accounted as issued, that caused
reporting of hugely over-inflated numbers, having nothing to do
with actual disk I/O. This change utilizes never used field in
struct dsl_scan_phys to account such skipped bytes, allowing to
report how much data were actually scrubbed/resilvered and what
is the actual I/O speed. While formally it is an on-disk format
change, it should be compatible both ways, so should not need a
feature flag.
This should partially address the same issue as c85ac731a0, but
from a different perspective, complementing it.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Akash B <akash-b@hpe.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#15007
Switch FIFO queues (SYNC/TRIM) and active queue of vdev queue from
time-sorted AVL-trees to simple lists. AVL-trees are too expensive
for such a simple task. To change I/O priority without searching
through the trees, add io_queue_state field to struct zio.
To not check number of queued I/Os for each priority add vq_cqueued
bitmap to struct vdev_queue. Update it when adding/removing I/Os.
Make vq_cactive a separate array instead of struct vdev_queue_class
member. Together those allow to avoid lots of cache misses when
looking for work in vdev_queue_class_to_issue().
Introduce deadline of ~0.5s for LBA-sorted queues. Before this I
saw some I/Os waiting in a queue for up to 8 seconds and possibly
more due to starvation. With this change I no longer see it. I
had to slightly more complicate the comparison function, but since
it uses all the same cache lines the difference is minimal. For a
sequential I/Os the new code in vdev_queue_io_to_issue() actually
often uses more simple avl_first(), falling back to avl_find() and
avl_nearest() only when needed.
Arrange members in struct zio to access only one cache line when
searching through vdev queues. While there, remove io_alloc_node,
reusing the io_queue_node instead. Those two are never used same
time.
Remove zfs_vdev_aggregate_trim parameter. It was disabled for 4
years since implemented, while still wasted time maintaining the
offset-sorted tree of TRIM requests. Just remove the tree.
Remove locking from txg_all_lists_empty(). It is racy by design,
while 2 pair of locks/unlocks take noticeable time under the vdev
queue lock.
With these changes in my tests with volblocksize=4KB I measure vdev
queue lock spin time reduction by 50% on read and 75% on write.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14925
It's been observed that in certain workloads (zvol-related being a
big one), ZFS will end up spending a large amount of time spinning
up taskqs only to tear them down again almost immediately, then
spin them up again...
I noticed this when I looked at what my mostly-idle system was doing
and wondered how on earth taskq creation/destroy was a bunch of time...
So I added a configurable delay to avoid it tearing down tasks the
first time it notices them idle, and the total number of threads at
steady state went up, but the amount of time being burned just
tearing down/turning up new ones almost vanished.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#14938
It was a vdev level read cache, designed to aggregate many small
reads by speculatively issuing bigger reads instead and caching
the result. But since it has almost no idea about what is going
on with exception of ZIO_FLAG_DONT_CACHE flag set by higher layers,
it was found to make more harm than good, for which reason it was
disabled for the past 12 years. These days we have much better
instruments to enlarge the I/Os, such as speculative and prescient
prefetches, I/O scheduler, I/O aggregation etc.
Besides just the dead code removal this removes one extra mutex
lock/unlock per write inside vdev_cache_write(), not otherwise
disabled and trying to do some work.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14953
This is more-or-less like `zfs send`, but specifying the snapshot by its
objset id for situations where it can't be referenced any other way.
Sponsored-By: Klara, Inc.
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: WHR <msl0000023508@gmail.com>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Closes#14642
Make the section heading more generic (the section relates to ZFS files
as well as ZFS volumes).
Swapping to a ZFS volume is prone to deadlock. Remove the related
instruction, direct readers to OpenZFS FAQ. Related, but not linked
from within the manual page:
<https://openzfs.github.io/openzfs-docs/Project%20and%20Community/FAQ.html#using-a-zvol-for-a-swap-device-on-linux>
(Using a zvol for a swap device on Linux).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Graham Perrin <grahamperrin@freebsd.org>
Issue #7734Closes#14756
GRUB2 is compatible with all "read-only compatible" features,
so it is safe to add new features of this type to the grub2
compatibility list. We generally want to include all compatible
features, to minimize the differences between grub2-compatible
pools and no-compatibility pools.
Adding new properties `livelist` and `zpool_checkpoint` accordingly.
Also adding them to the man page which references this file as an
example, for consistency.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Colm Buckley <colm@tuatha.org>
Closes#14893
Added a flag '-e' in zpool scrub to scrub only blocks in error log. A
user can pause, resume and cancel the error scrub by passing additional
command line arguments -p -s just like a regular scrub. This involves
adding a new flag, creating new libzfs interfaces, a new ioctl, and the
actual iteration and read-issuing logic. Error scrubbing is executed in
multiple txg to make sure pool performance is not affected.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Co-authored-by: TulsiJain tulsi.jain@delphix.com
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#8995Closes#12355
zpool initialize functions well for touching every free byte...once.
But if we want to do it again, we're currently out of luck.
So let's add zpool initialize -u to clear it.
Co-authored-by: Rich Ercolani <rincebrain@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12451Closes#14873
In case check_filesystem() does not error out and does not report
an error, remove that error block from error lists and logs
without requiring a scrub. This can happen when the original file and
all snapshots/clones referencing it have been removed.
Otherwise zpool status will still report that "Permanent errors have
been detected..." without actually reporting any of them.
To implement this change the functions introduced in corrective
receive were modified to take into account the head_errlog feature.
Before this change:
=============================
pool: test
state: ONLINE
status: One or more devices has experienced an error resulting in data
corruption. Applications may be affected.
action: Restore the file in question if possible. Otherwise restore the
entire pool from backup.
see: https://openzfs.github.io/openzfs-docs/msg/ZFS-8000-8A
config:
NAME STATE READ WRITE CKSUM
test ONLINE 0 0 0
/home/user/vdev_a ONLINE 0 0 2
errors: Permanent errors have been detected in the following files:
=============================
After this change:
=============================
pool: test
state: ONLINE
status: One or more devices has experienced an unrecoverable error. An
attempt was made to correct the error. Applications are
unaffected.
action: Determine if the device needs to be replaced, and clear the
errors
using 'zpool clear' or replace the device with 'zpool replace'.
see: https://openzfs.github.io/openzfs-docs/msg/ZFS-8000-9P
config:
NAME STATE READ WRITE CKSUM
test ONLINE 0 0 0
/home/user/vdev_a ONLINE 0 0 2
errors: No known data errors
=============================
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#14813
For the head_errlog feature use dsl_dataset_hold_obj_flags() instead of
dsl_dataset_hold_obj() in order to enable access to the encryption keys
(if loaded). This enables reporting of errors in encrypted filesystems
which are not mounted but have their keys loaded.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#14837
This commit expands on the zhack label repair command in d04b5c9 by
adding the -u option to undetach a device by regenerating uberblocks,
in addition to the existing functionality of fixing checksums, now
represented by -c. Previous behavior is retained in the case of no
options.
The changes are heavily inspired by Jeff Bonwick's labelfix
utility, as archived at:
https://gist.github.com/jjwhitney/baaa63144da89726e482
Additionally, it is now capable of properly determining the size of
block devices and other media, as well as handling sizes which are
not divisible by 2^18. This should make it viable for use on physical
devices and partitions, in addition to files.
These changes should make it possible to import zpools that have had
their uberblocks erased, such as in the case of pools rendered
inaccessible by erroneous detach commands.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: buzzingwires <buzzingwires@outlook.com>
Closes#14773
Usage:
zpool set org.freebsd:comment="this is my pool" poolname
Tests are based on zfs_set's user property tests.
Also stop truncating property values at MAXNAMELEN, use ZFS_MAXPROPLEN.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Mateusz Piotrowski <mateusz.piotrowski@klarasystems.com>
Sponsored-by: Beckhoff Automation GmbH & Co. KG.
Sponsored-by: Klara Inc.
Closes#11680
