When building (s)rpm files through the Makefile, a directory structure
is created in /tmp to hold the various files.
In case the user running the command has overridden some of the RPM path
settings through their user profile (for example in `~/.rpmmacros`),
these paths do not line up with the configuration, and the build fails.
Make sure all paths used are properly defined.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ralf Ertzinger <ralf@skytale.net>
Closes#15756
The zfs-initramfs package has never worked as no RPM-based distribution
uses initramfs-tools, which is listed as a dependency of zfs-initramfs.
This would not ordinarily be a problem, as it is only enabled when
/usr/share/initramfs-tools is present, which should not normally be the
case on RPM-based distributions. However, other packages may install
unused files there even if initramfs-tools is not used, so remove this
auto-detection for the rpm-utils target.
This does not fully remove the logic for the zfs-initramfs package. This
splits it out into a separate rpm-utils-initramfs target so that the
Debian builds can still use it.
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Harald van Dijk <harald@gigawatt.nl>
Closes#10898
When building srpm using make -j, each of the recursive makes invoked to
build srpm-{dkms,kmod,utils} will build the dist target. This is both
unnecessary, and also has a very good chance of breaking when they race
trying to build gitrev.
Fix this by make dist a prerequisite of srpm-{dkms,kmod,utils} instead
of srpm-common, so that it will be done once before invoking the
recursive makes.
Also, gitrev is not really required for make dist, so instead of adding
it to BUILT_SOURCES, just add it as a prerequisite of the all target.
Mark the individual package targets as PHONY.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Closes#10564
Build products from an out of tree build should be written
relative to the build directory. Sources should be referred
to by their locations in the source directory.
This is accomplished by adding the 'src' and 'obj' variables
for the module Makefile.am, using relative paths to reference
source files, and by setting VPATH when source files are not
co-located with the Makefile. This enables the following:
$ mkdir build
$ cd build
$ ../configure \
--with-spl=$HOME/src/git/spl/ \
--with-spl-obj=$HOME/src/git/spl/build
$ make -s
This change also has the advantage of resolving the following
warning which is generated by modern versions of automake.
Makefile.am:00: warning: source file 'xxx' is in a subdirectory,
Makefile.am:00: but option 'subdir-objects' is disabled
Signed-off-by: Turbo Fredriksson <turbo@bayour.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1082
Set LANG=C before calling 'rpmbuild' to avoid rpmbuild failing on
the translated date string in the changelog.
Signed-off-by: Turbo Fredriksson <turbo@bayour.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes: zfsonlinux/spl#306
Refresh the existing RPM packaging to conform to the 'Fedora
Packaging Guidelines'. This includes adopting the kmods2
packaging standard which is used fod kmods distributed by
rpmfusion for Fedora/RHEL.
http://fedoraproject.org/wiki/Packaging:Guidelineshttp://rpmfusion.org/Packaging/KernelModules/Kmods2
While the spec files have been entirely rewritten from a
user perspective the only major changes are:
* The Fedora packages now have a build dependency on the
rpmfusion repositories. The generic kmod packages also
have a new dependency on kmodtool-1.22 but it is bundled
with the source rpm so no additional packages are needed.
* The kernel binary module packages have been renamed from
zfs-modules-* to kmod-zfs-* as specificed by kmods2.
* The is now a common kmod-zfs-devel-* package in addition
to the per-kernel devel packages. The common package
contains the development headers while the per-kernel
package contains kernel specific build products.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1341
This commit adds support for building a zfs-modules-dkms sub package
built around Dynamic Kernel Module Support. This is to allow building
packages using the DKMS infrastructure which is intended to ease the
burden of kernel version changes, upgrades, etc.
By default zfs-modules-dkms-* sub package will be built as part of
the 'make rpm' target. Alternately, you can build only the DKMS
module package using the 'make rpm-dkms' target.
Examples:
# To build packaged binaries as well as a dkms packages
$ ./configure && make rpm
# To build only the packaged binary utilities and dkms packages
$ ./configure && make rpm-utils rpm-dkms
Note: Only the RHEL 5/6, CHAOS 5, and Fedora distributions are
supported for building the dkms sub package.
Signed-off-by: Prakash Surya <surya1@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #535
Currently, when configure --with-config is used, selective compilation
is only effective for the simple "make" case. Package builders (e.g.
make rpm) still build everything (utils and modules). This patch fixes
that.
Signed-off-by: Prakash Surya <surya1@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #851
Allow rigorous (and expensive) tx validation to be enabled/disabled
indepentantly from the standard zfs debugging. When enabled these
checks ensure that all txs are constructed properly and that a dbuf
is never dirtied without taking the correct tx hold.
This checking is particularly helpful when adding new dmu consumers
like Lustre. However, for established consumers such as the zpl
with no known outstanding tx construction problems this is just
overhead.
--enable-debug-dmu-tx - Enable/disable validation of each tx as
--disable-debug-dmu-tx it is constructed. By default validation
is disabled due to performance concerns.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Allow a source rpm to be rebuilt with debugging enabled. This
avoids the need to have to manually modify the spec file. By
default debugging is still largely disabled. To enable specific
debugging features use the following options with rpmbuild.
'--with debug' - Enables ASSERTs
# For example:
$ rpmbuild --rebuild --with debug zfs-modules-0.6.0-rc6.src.rpm
Additionally, ZFS_CONFIG has been added to zfs_config.h for
packages which build against these headers. This is critical
to ensure both zfs and the dependant package are using the same
prototype and structure definitions.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Add autoconf style build infrastructure to the ZFS tree. This
includes autogen.sh, configure.ac, m4 macros, some scripts/*,
and makefiles for all the core ZFS components.
