Adding O_DIRECT support to ZFS to bypass the ARC for writes/reads.
O_DIRECT support in ZFS will always ensure there is coherency between
buffered and O_DIRECT IO requests. This ensures that all IO requests,
whether buffered or direct, will see the same file contents at all
times. Just as in other FS's , O_DIRECT does not imply O_SYNC. While
data is written directly to VDEV disks, metadata will not be synced
until the associated TXG is synced.
For both O_DIRECT read and write request the offset and request sizes,
at a minimum, must be PAGE_SIZE aligned. In the event they are not,
then EINVAL is returned unless the direct property is set to always (see
below).
For O_DIRECT writes:
The request also must be block aligned (recordsize) or the write
request will take the normal (buffered) write path. In the event that
request is block aligned and a cached copy of the buffer in the ARC,
then it will be discarded from the ARC forcing all further reads to
retrieve the data from disk.
For O_DIRECT reads:
The only alignment restrictions are PAGE_SIZE alignment. In the event
that the requested data is in buffered (in the ARC) it will just be
copied from the ARC into the user buffer.
For both O_DIRECT writes and reads the O_DIRECT flag will be ignored in
the event that file contents are mmap'ed. In this case, all requests
that are at least PAGE_SIZE aligned will just fall back to the buffered
paths. If the request however is not PAGE_SIZE aligned, EINVAL will
be returned as always regardless if the file's contents are mmap'ed.
Since O_DIRECT writes go through the normal ZIO pipeline, the
following operations are supported just as with normal buffered writes:
Checksum
Compression
Encryption
Erasure Coding
There is one caveat for the data integrity of O_DIRECT writes that is
distinct for each of the OS's supported by ZFS.
FreeBSD - FreeBSD is able to place user pages under write protection so
any data in the user buffers and written directly down to the
VDEV disks is guaranteed to not change. There is no concern
with data integrity and O_DIRECT writes.
Linux - Linux is not able to place anonymous user pages under write
protection. Because of this, if the user decides to manipulate
the page contents while the write operation is occurring, data
integrity can not be guaranteed. However, there is a module
parameter `zfs_vdev_direct_write_verify` that controls the
if a O_DIRECT writes that can occur to a top-level VDEV before
a checksum verify is run before the contents of the I/O buffer
are committed to disk. In the event of a checksum verification
failure the write will return EIO. The number of O_DIRECT write
checksum verification errors can be observed by doing
`zpool status -d`, which will list all verification errors that
have occurred on a top-level VDEV. Along with `zpool status`, a
ZED event will be issues as `dio_verify` when a checksum
verification error occurs.
ZVOLs and dedup is not currently supported with Direct I/O.
A new dataset property `direct` has been added with the following 3
allowable values:
disabled - Accepts O_DIRECT flag, but silently ignores it and treats
the request as a buffered IO request.
standard - Follows the alignment restrictions outlined above for
write/read IO requests when the O_DIRECT flag is used.
always - Treats every write/read IO request as though it passed
O_DIRECT and will do O_DIRECT if the alignment restrictions
are met otherwise will redirect through the ARC. This
property will not allow a request to fail.
There is also a module parameter zfs_dio_enabled that can be used to
force all reads and writes through the ARC. By setting this module
parameter to 0, it mimics as if the direct dataset property is set to
disabled.
Reviewed-by: Brian Behlendorf <behlendorf@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Atkinson <batkinson@lanl.gov>
Co-authored-by: Mark Maybee <mark.maybee@delphix.com>
Co-authored-by: Matt Macy <mmacy@FreeBSD.org>
Co-authored-by: Brian Behlendorf <behlendorf@llnl.gov>
Closes#10018
zpool upgraded with 'feature@project_quota' needs re-layout of SA's
to fix the SA_ZPL_PROJID at SA_PROJID_OFFSET (128). Its necessary for
the correct accounting of object usage against its projid.
Old object (created before upgrade) when gets a projid assigned, its
SA gets re-layout via sa_add_projid(). If object has xattr dir, SA
of xattr dir also gets re-layout. But SA re-layout of xattr objects
inside a xattr dir is not done.
Fix zfs_setattr_dir() to re-layout SA's on xattr objects, when setting
projid on old xattr object (created before upgrade).
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jitendra Patidar <jitendra.patidar@nutanix.com>
Closes#16355Closes#16356
Since the change to folios it has just been a wrapper anyway. Linux has
removed their wrapper, so we add one.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <robn@despairlabs.com>
Sponsored-by: https://despairlabs.com/sponsor/Closes#16400
1) Make mmap flushes synchronous. Linux may skip flushing dirty pages
already in writeback unless data-integrity sync is requested.
2) Change zfs_putpage to use TXG_WAIT. Otherwise dirty pages may be
skipped due to DMU pushing back on TX assign.
3) Add missing mmap flush when doing block cloning.
4) While here, pass errors from putpage to writepage/writepages.
This change fixes corruption edge cases, but unfortunately adds
synchronous ZIL flushes for dirty mmap pages to llseek and bclone
operations. It may be possible to avoid these sync writes later
but would need more tricky refactoring of the writeback code.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Robert Evans <evansr@google.com>
Closes#15933Closes#16019
On Linux the ioctl_ficlonerange() and ioctl_ficlone() system calls
are expected to either fully clone the specified range or return an
error. The range may be for an entire file. While internally ZFS
supports cloning partial ranges there's no way to return the length
cloned to the caller so we need to make this all or nothing.
As part of this change support for the REMAP_FILE_CAN_SHORTEN flag
has been added. When REMAP_FILE_CAN_SHORTEN is set zfs_clone_range()
will return a shortened range when encountering pending dirty records.
When it's clear zfs_clone_range() will block and wait for the records
to be written out allowing the blocks to be cloned.
Furthermore, the file range lock is held over the region being cloned
to prevent it from being modified while cloning. This doesn't quite
provide an atomic semantics since if an error is encountered only a
portion of the range may be cloned. This will be converted to an
error if REMAP_FILE_CAN_SHORTEN was not provided and returned to the
caller. However, the destination file range is left in an undefined
state.
A test case has been added which exercises this functionality by
verifying that `cp --reflink=never|auto|always` works correctly.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#15728Closes#15842
In db4fc559c I messed up and changed this bit of code to set the inode
atime to an uninitialised value, when actually it was just supposed to
loading the atime from the inode to be stored in the SA. This changes it
to what it should have been.
Ensure times change by the right amount Previously, we only checked
if the times changed at all, which missed a bug where the atime was
being set to an undefined value.
Now ensure the times change by two seconds (or thereabouts), ensuring
we catch cases where we set the time to something bonkers
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <robn@despairlabs.com>
Sponsored-by: https://despairlabs.com/sponsor/Closes#15762Closes#15773
We need to wait until after having done a zfs_enter() to load some
fields from the zfsvfs structure. Otherwise a use-after-free is
possible in the face of a concurrent rollback.
Other functions in this file are careful to avoid this bug, I believe
this is the only instance.
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#15752
6.6 made i_ctime inaccessible; 6.7 has done the same for i_atime and
i_mtime. This extends the method used for ctime in b37f29341 to atime
and mtime as well.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <robn@despairlabs.com>
Sponsored-by: https://github.com/sponsors/robnCloses#15681
Copy the disable parameter that FreeBSD implemented, and extend it to
work on Linux as well, until we're sure this is stable.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#15529
Private read/write mapping can't be used to modify the mapped files, so
they will remain be immutable. Private read/write mappings are usually
used to load the data segment of executable files, rejecting them will
rendering immutable executable files to stop working.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: WHR <msl0000023508@gmail.com>
Closes#15344
ZVOL:
- Mark all ZVOL ZIL transactions as sync. Since ZVOLs have only
one object, it makes no sense to maintain async queue and on each
commit merge it into sync. Single sync queue is just cheaper, while
it changes nothing until actual commit request arrives.
- Remove zsd_sync_cnt and the zil_async_to_sync() calls since we
are no longer switching between sync and async queues.
ZFS:
- Mark write transactions as sync based only on number of sync
opens (z_sync_cnt). We can not randomly jump between sync and
async unless we want data corruptions due to writes reordering.
- When file first opened with O_SYNC (z_sync_cnt incremented to 1)
call zil_async_to_sync() for it to preserve correct ordering between
past and future writes.
- Drop zfs_fsyncer_key logic. Looks like it was an optimization
for workloads heavily intermixing async writes with tons of fsyncs.
But first it was broken 8 years ago due to Linux tsd implementation
not allowing data storage between syscalls, and second, I doubt it
is safe to switch from async to sync so often and without calling
zil_async_to_sync().
- Rename sync argument of *_log_write() into commit, now only
signalling caller's intent to call zil_commit() soon after. It
allows WR_COPIED optimizations without extra other meanings.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Wilson <george.wilson@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#15366
In commit 0d72b92883c651a11059d93335f33d65c6eb653b, a new u32 argument
for the request_mask was added to generic_fillattr. This is the same
request_mask for statx that's present in the most recent API implemented
by zpl_getattr_impl. This commit conditionally adds it to the
zpl_generic_fillattr(...) macro, as well as the zfs_getattr_fast(...)
implementation, when configure determines it's present in the kernel's
generic_fillattr(...).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#15263
In Linux commit 13bc24457850583a2e7203ded05b7209ab4bc5ef, direct access
to the i_ctime member of struct inode was removed. The new approach is
to use accessor methods that exclusively handle passing the timestamp
around by value. This change adds new tests for each of these functions
and introduces zpl_* equivalents in include/os/linux/zfs/sys/zpl.h. In
where the inode_get/set_ctime*() functions exist, these zpl_* calls will
be mapped to the new functions. On older kernels, these macros just wrap
direct-access calls. The code that operated on an address of ip->i_ctime
to call ZFS_TIME_DECODE() now will take a local copy using
zpl_inode_get_ctime(), and then pass the address of the local copy when
performing the ZFS_TIME_DECODE() call, in all cases, rather than
directly accessing the member.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#15263Closes#15257
- Split dmu_prefetch_dnode() from dmu_prefetch() into a separate
function. It is quite inconvenient to read the code where len = 0
means dnode prefetch instead indirect/data prefetch. One function
doing both has no benefits, since the code paths are independent.
- Improve dmu_prefetch() handling of long block ranges. Instead
of limiting L0 data length to prefetch for to dmu_prefetch_max,
make dmu_prefetch_max limit the actual amount of prefetch at the
specified level, and, if there is more, prefetch all the rest at
higher indirection level. It should improve random access times
within the prefetched range of any length, reducing importance of
specific dmu_prefetch_max value.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#15076
Multiple changes to the blkdev API were introduced in Linux 6.5. This
includes passing (void* holder) to blkdev_put, adding a new
blk_holder_ops* arg to blkdev_get_by_path, adding a new blk_mode_t type
that replaces uses of fmode_t, and removing an argument from the release
handler on block_device_operations that we weren't using. The open
function definition has also changed to take gendisk* and blk_mode_t, so
update it accordingly, too.
Implement local wrappers for blkdev_get_by_path() and
vdev_blkdev_put() so that the in-line calls are cleaner, and place the
conditionally-compiled implementation details inside of both of these
local wrappers. Both calls are exclusively used within vdev_disk.c, at
this time.
Add blk_mode_is_open_write() to test FMODE_WRITE / BLK_OPEN_WRITE
The wrapper function is now used for testing using the appropriate
method for the kernel, whether the open mode is writable or not.
Emphasize fmode_t arg in zvol_release is not used
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#15099
Linux kernel 6.3 changed a bunch of APIs to use the dedicated idmap
type for mounts (struct mnt_idmap), we need to detect these changes
and make zfs work with the new APIs.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Youzhong Yang <yyang@mathworks.com>
Closes#14682
Clang's static analyzer points out that if we fail to find an extended
attribute directory, but somehow find it when calculating delete_now and
delete_now is true, we will have a NULL pointer dereference when we try
to unlink the extended attribute directory.
I am not sure if this is possible, but if it is, I do not see a sane way
of handling this other than rolling back the transaction and retrying.
For now, let us do an VERIFY_IMPLY(). If this trips, it will stop the
transaction from committing, which will prevent an attribute directory
leak.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14575
After 89cd2197b9 was merged, Clang's
static analyzer began complaining about a dead assignment in
`zfs_fillpage()`. Upon inspection, I noticed that the dead assignment
was because we are not using the calculated io_len that we should use to
avoid asking the DMU to read past the end of a file. This should result
in `dmu_buf_hold_array_by_dnode()` calling `zfs_panic_recover()`.
This issue predates 89cd2197b9, but its
simplification of zfs_fillpage() eliminated the only use of the
assignment to io_len, which made Clang's static analyzer complain about
the issue.
Also, as a precaution, we add an assertion that io_offset < i_size. If
this ever fails, bad things will happen. Otherwise, we are blindly
trusting the kernel not to give us invalid offsets. We continue to
blindly trust it on non-debug kernels.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14534
When a page is faulted in for memory mapped I/O the page lock
may be dropped before it has been read and marked up to date.
If a buffered read encounters such a page in mappedread() it
must wait until the page has been updated. Failure to do so
will result in a panic on debug builds and incorrect data on
production builds.
The critical part of this change is in mappedread() where pages
which are not up to date are now handled. Additionally, it
includes the following simplifications.
- zfs_getpage() and zfs_fillpage() could be passed an array of
pages. This could be more efficient if it was used but in
practice only a single page was ever provided. These
interfaces were simplified to acknowledge that.
- update_pages() was modified to correctly set the PG_error bit
on a page when it cannot be read by dmu_read().
- Setting PG_error and PG_uptodate was moved to zfs_fillpage()
from zpl_readpage_common(). This is consistent with the
handling in update_pages() and mappedread().
- Minor additional refactoring to comments and variable
declarations to improve readability.
- Add a test case to exercise concurrent buffered, direct,
and mmap IO to the same file.
- Reduce the mmap_sync test case default run time.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13608Closes#14498
As of the 4.13 kernel filemap_range_has_page() can be used to
check if there is a page mapped in a given file range. When
available this interface should be used which eliminates the
need for the zp->z_is_mapped boolean.
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#14493
I recently gained the ability to run Clang's static analyzer on the
linux kernel modules via a few hacks. This extended coverage to code
that was previously missed since Clang's static analyzer only looked at
code that we built in userspace. Running it against the Linux kernel
modules built from my local branch produced a total of 72 reports
against my local branch. Of those, 50 were reports of logic errors and
22 were reports of dead code. Since we already had cleaned up all of
the previous dead code reports, I felt it would be a good next step to
clean up these dead code reports. Clang did a further breakdown of the
dead code reports into:
Dead assignment 15
Dead increment 2
Dead nested assignment 5
The benefit of cleaning these up, especially in the case of dead nested
assignment, is that they can expose places where our error handling is
incorrect. A number of them were fairly straight forward. However
several were not:
In vdev_disk_physio_completion(), not only were we not using the return
value from the static function vdev_disk_dio_put(), but nothing used it,
so I changed it to return void and removed the existing (void) cast in
the other area where we call it in addition to no longer storing it to a
stack value.
In FSE_createDTable(), the function is dead code. Its helper function
FSE_freeDTable() is also dead code, as are the CPP definitions in
`module/zstd/include/zstd_compat_wrapper.h`. We just delete it all.
In zfs_zevent_wait(), we have an optimization opportunity. cv_wait_sig()
returns 0 if there are waiting signals and 1 if there are none. The
Linux SPL version literally returns `signal_pending(current) ? 0 : 1)`
and FreeBSD implements the same semantics, we can just do
`!cv_wait_sig()` in place of `signal_pending(current)` to avoid
unnecessarily calling it again.
zfs_setattr() on FreeBSD version did not have error handling issue
because the code was removed entirely from FreeBSD version. The error is
from updating the attribute directory's files. After some thought, I
decided to propapage errors on it to userspace.
In zfs_secpolicy_tmp_snapshot(), we ignore a lack of permission from the
first check in favor of checking three other permissions. I assume this
is intentional.
In zfs_create_fs(), the return value of zap_update() was not checked
despite setting an important version number. I see no backward
compatibility reason to permit failures, so we add an assertion to catch
failures. Interestingly, Linux is still using ASSERT(error == 0) from
OpenSolaris while FreeBSD has switched to the improved ASSERT0(error)
from illumos, although illumos has yet to adopt it here. ASSERT(error ==
0) was used on Linux while ASSERT0(error) was used on FreeBSD since the
entire file needs conversion and that should be the subject of
another patch.
dnode_move()'s issue was caused by us not having implemented
POINTER_IS_VALID() on Linux. We have a stub in
`include/os/linux/spl/sys/kmem_cache.h` for it, when it really should be
in `include/os/linux/spl/sys/kmem.h` to be consistent with
Illumos/OpenSolaris. FreeBSD put both `POINTER_IS_VALID()` and
`POINTER_INVALIDATE()` in `include/os/freebsd/spl/sys/kmem.h`, so we
copy what it did.
Whenever a report was in platform-specific code, I checked the FreeBSD
version to see if it also applied to FreeBSD, but it was only relevant a
few times.
Lastly, the patch that enabled Clang's static analyzer to be run on the
Linux kernel modules needs more work before it can be put into a PR. I
plan to do that in the future as part of the on-going static analysis
work that I am doing.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14380
zfs_zaccess_trivial() calls the generic_permission() to read
xattr attributes. This causes deadlock if called from
zpl_xattr_set_dir() context as xattr and the dent locks are
already held in this scenario. This commit skips the permissions
checks for extended attributes since the Linux VFS stack already
checks it before passing us the control.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Youzhong Yang <yyang@mathworks.com>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#14220
There was the series from me a year ago which fixed most of the
callback vs implementation prototype mismatches. It was based on
running the CFI-enabled kernel (in permissive mode -- warning
instead of panic) and performing a full ZTS cycle, and then fixing
all of the problems caught by CFI.
Now, Clang 16-dev has new warning flag, -Wcast-function-type-strict,
which detect such mismatches at compile-time. It allows to find the
remaining issues missed by the first series.
There are only two of them left: one for the
secpolicy_vnode_setattr() callback and one for taskq_dispatch().
The fix is easy, since they are not used anywhere else.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Closes#14207
Linux 5.17 commit torvalds/linux@5dfbfe71e enables "the idmapping
infrastructure to support idmapped mounts of filesystems mounted
with an idmapping". Update the OpenZFS accordingly to improve the
idmapped mount support.
This pull request contains the following changes:
- xattr setter functions are fixed to take mnt_ns argument. Without
this, cp -p would fail for an idmapped mount in a user namespace.
- idmap_util is enhanced/fixed for its use in a user ns context.
- One test case added to test idmapped mount in a user ns.
Reviewed-by: Christian Brauner <christian@brauner.io>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Youzhong Yang <yyang@mathworks.com>
Closes#14097
Implement support for Linux's RENAME_* flags (for renameat2). Aside from
being quite useful for userspace (providing race-free ways to exchange
paths and implement mv --no-clobber), they are used by overlayfs and are
thus required in order to use overlayfs-on-ZFS.
In order for us to represent the new renameat2(2) flags in the ZIL, we
create two new transaction types for the two flags which need
transactional-level support (RENAME_EXCHANGE and RENAME_WHITEOUT).
RENAME_NOREPLACE does not need any ZIL support because we know that if
the operation succeeded before creating the ZIL entry, there was no file
to be clobbered and thus it can be treated as a regular TX_RENAME.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Pavel Snajdr <snajpa@snajpa.net>
Signed-off-by: Aleksa Sarai <cyphar@cyphar.com>
Closes#12209Closes#14070
This is in preparation for RENAME_EXCHANGE and RENAME_WHITEOUT support
for ZoL, but the changes here allow for far nicer fallbacks than the
previous implementation (the source and target are re-linked in case of
the final link failing).
In addition, a small cleanup was done for the "target exists but is a
different type" codepath so that it's more understandable.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Aleksa Sarai <cyphar@cyphar.com>
Closes#12209Closes#14070
Adds support for idmapped mounts. Supported as of Linux 5.12 this
functionality allows user and group IDs to be remapped without changing
their state on disk. This can be useful for portable home directories
and a variety of container related use cases.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Youzhong Yang <yyang@mathworks.com>
Closes#12923Closes#13671
Replace ZFS_ENTER and ZFS_VERIFY_ZP, which have hidden returns, with
functions that return error code. The reason we want to do this is
because hidden returns are not obvious and had caused some missing fail
path unwinding.
This patch changes the common, linux, and freebsd parts. Also fixes
fail path unwinding in zfs_fsync, zpl_fsync, zpl_xattr_{list,get,set}, and
zfs_lookup().
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Chunwei Chen <david.chen@nutanix.com>
Closes#13831
Page writebacks with WB_SYNC_NONE can take several seconds to complete
since they wait for the transaction group to close before being
committed. This is usually not a problem since the caller does not
need to wait. However, if we're simultaneously doing a writeback
with WB_SYNC_ALL (e.g via msync), the latter can block for several
seconds (up to zfs_txg_timeout) due to the active WB_SYNC_NONE
writeback since it needs to wait for the transaction to complete
and the PG_writeback bit to be cleared.
This commit deals with 2 cases:
- No page writeback is active. A WB_SYNC_ALL page writeback starts
and even completes. But when it's about to check if the PG_writeback
bit has been cleared, another writeback with WB_SYNC_NONE starts.
The sync page writeback ends up waiting for the non-sync page
writeback to complete.
- A page writeback with WB_SYNC_NONE is already active when a
WB_SYNC_ALL writeback starts. The WB_SYNC_ALL writeback ends up
waiting for the WB_SYNC_NONE writeback.
The fix works by carefully keeping track of active sync/non-sync
writebacks and committing when beneficial.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Shaan Nobee <sniper111@gmail.com>
Closes#12662Closes#12790
Bypass check of ZFS aces if the ACL is trivial. When an ACL is
trivial its permissions are represented by the mode without any
loss of information. In this case, it is safe to convert the
access request into equivalent mode and then pass desired mask
and inode to generic_permission(). This has the added benefit
of also checking whether entries in a POSIX ACL on the file grant
the desired access.
This commit also skips the ACL check on looking up the xattr dir
since such restrictions don't exist in Linux kernel and it makes
xattr lookup behavior inconsistent between SA and file-based
xattrs. We also don't want to perform a POSIX ACL check while
looking up the POSIX ACL if for some reason it is located in
the xattr dir rather than an SA.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Andrew Walker <awalker@ixsystems.com>
Closes#13237
This allows reads/writes caused by accesses to mmap files to be
accounted correctly in the per-dataset kstats for both Linux and
FreeBSD.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <freqlabs@FreeBSD.org>
Signed-off-by: Matthias Blankertz <matthias@blankertz.org>
Closes#12994Closes#13044
69 CSTYLED BEGINs remain, appx. 30 of which can be removed if cstyle(1)
had a useful policy regarding
CALL(ARG1,
ARG2,
ARG3);
above 2 lines. As it stands, it spits out *both*
sysctl_os.c: 385: continuation line should be indented by 4 spaces
sysctl_os.c: 385: indent by spaces instead of tabs
which is very cool
Another >10 could be fixed by removing "ulong" &al. handling.
I don't foresee anyone actually using it intentionally
(does it even exist in modern headers? why did it in the first place?).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12993
Evaluated every variable that lives in .data (and globals in .rodata)
in the kernel modules, and constified/eliminated/localised them
appropriately. This means that all read-only data is now actually
read-only data, and, if possible, at file scope. A lot of previously-
global-symbols became inlinable (and inlined!) constants. Probably
not in a big Wowee Performance Moment, but hey.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12899
Instead, linux/pagemap.h offers a number of folio-specific functions to
be called instead. In this case, module/os/linux/zfs/zfs_vnops_os.c
wants to call wait_on_page_bit(pp, PG_writeback). This gets replaced
with folio_wait_bit(folio_page(pp), PG_writeback). This change modifies
the code to conditionally compile that if configure identifies th
presence of the folio_wait_bit() function.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#12800
* zio: avoid callback typecasting
* zil: avoid zil_itxg_clean() callback typecasting
* zpl: decouple zpl_readpage() into two separate callbacks
* nvpair: explicitly declare callbacks for xdr_array()
* linux/zfs_nvops: don't use external iput() as a callback
* zcp_synctask: don't use fnvlist_free() as a callback
* zvol: don't use ops->zv_free() as a callback for taskq_dispatch()
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Closes#12260
Reviewed-by: Adam Moss <c@yotes.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11972
Quoting <linux/exportfs.h>:
> encode_fh() should return the fileid_type on success and on error
> returns 255 (if the space needed to encode fh is greater than
> @max_len*4 bytes). On error @max_len contains the minimum size (in 4
> byte unit) needed to encode the file handle.
ZFS was not setting max_len in the case where the handle was too
small. As a result of this, the `t_name_to_handle_at.c' example in
name_to_handle_at(2) did not work on ZFS.
zfsctl_fid() will itself set max_len if called with a fid that is too
small, so if we give zfs_fid() that behavior as well, the fix is quite
easy: if the handle is too small, just use a zero-size fid instead of
the handle.
Tested by running t_name_to_handle_at on a normal file, a directory, a
.zfs directory, and a snapshot.
Thanks-to: Puck Meerburg <puck@puckipedia.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Alyssa Ross <hi@alyssa.is>
Closes#11995
Correct an assortment of typos throughout the code base.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Closes#11774
In Linux 5.12, the filesystem API was modified to support ipmapped
mounts by adding a "struct user_namespace *" parameter to a number
functions and VFS handlers. This change adds the needed autoconf
macros to detect the new interfaces and updates the code appropriately.
This change does not add support for idmapped mounts, instead it
preserves the existing behavior by passing the initial user namespace
where needed. A subsequent commit will be required to add support
for idmapped mounted.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#11712
zfs_znode_update_vfs is a more platform-agnostic name than
zfs_inode_update. Besides that, the function's prototype is moved to
include/sys/zfs_znode.h as the function is also used in common code.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ka Ho Ng <khng300@gmail.com>
Sponsored by: The FreeBSD Foundation
Closes#11580
There is a race condition in zfs_zrele_async when we are checking if
we would be the one to evict an inode. This can lead to a txg sync
deadlock.
Instead of calling into iput directly, we attempt to perform the atomic
decrement ourselves, unless that would set the i_count value to zero.
In that case, we dispatch a call to iput to run later, to prevent a
deadlock from occurring.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#11527Closes#11530
In FreeBSD the struct uio was just a typedef to uio_t. In order to
extend this struct, outside of the definition for the struct uio, the
struct uio has been embedded inside of a uio_t struct.
Also renamed all the uio_* interfaces to be zfs_uio_* to make it clear
this is a ZFS interface.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Brian Atkinson <batkinson@lanl.gov>
Closes#11438
As of the 5.10 kernel the generic splice compatibility code has been
removed. All filesystems are now responsible for registering a
->splice_read and ->splice_write callback to support this operation.
The good news is the VFS provided generic_file_splice_read() and
iter_file_splice_write() callbacks can be used provided the ->iter_read
and ->iter_write callback support pipes. However, this is currently
not the case and only iovecs and bvecs (not pipes) are ever attached
to the uio structure.
This commit changes that by allowing full iov_iter structures to be
attached to uios. Ever since the 4.9 kernel the iov_iter structure
has supported iovecs, kvecs, bvevs, and pipes so it's desirable to
pass the entire thing when possible. In conjunction with this the
uio helper functions (i.e uiomove(), uiocopy(), etc) have been
updated to understand the new UIO_ITER type.
Note that using the kernel provided uio_iter interfaces allowed the
existing Linux specific uio handling code to be simplified. When
there's no longer a need to support kernel's older than 4.9, then
it will be possible to remove the iovec and bvec members from the
uio structure and always use a uio_iter. Until then we need to
maintain all of the existing types for older kernels.
Some additional refactoring and cleanup was included in this change:
- Added checks to configure to detect available iov_iter interfaces.
Some are available all the way back to the 3.10 kernel and are used
when available. In particular, uio_prefaultpages() now always uses
iov_iter_fault_in_readable() which is available for all supported
kernels.
- The unused UIO_USERISPACE type has been removed. It is no longer
needed now that the uio_seg enum is platform specific.
- Moved zfs_uio.c from the zcommon.ko module to the Linux specific
platform code for the zfs.ko module. This gets it out of libzfs
where it was never needed and keeps this Linux specific code out
of the common sources.
- Removed unnecessary O_APPEND handling from zfs_iter_write(), this
is redundant and O_APPEND is already handled in zfs_write();
Reviewed-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11351
