The checksum histograms were intended to be used with ATA and parallel
SCSI, which are obsolete. With modern storage hardware, they will
almost always look like white noise; all bits will be wrong. They only
serve to bloat the event. That's a particular problem on FreeBSD, where
events must fit into a 1016 byte buffer.
This fixes issue #14717 for RAIDZ pools, but not for mirror pools.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Rich Ercolani <rincebrain@gmail.com>
Signed-off-by: Alan Somers <asomers@gmail.com>
Sponsored-by: Axcient
Closes#15052
Since spa_min_alloc may not be a power of 2, unlike ashifts, in the
case of DRAID, we should not select the minimal value among several
vdevs. Rounding to a multiple of it is unlikely to work for other
vdevs. Instead, using the greatest common divisor produces smaller
yet more reasonable results.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#15067
Ashift can be set for a vdev only during its creation, and the
top-level vdev does not change when a vdev is attached or replaced.
The ashift property should not be used during attachment, as it
does not allow attaching/replacing a vdev if the pool's ashift
property is increased after the existing vdev was created. Instead,
we should be able to attach the vdev if the attached vdev can
satisfy the ashift requirement with its parent.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#15061
The disk_check_media_change() function was added which replaces
bdev_check_media_change. This change was introduced in 6.5rc1
444aa2c58cb3b6cfe3b7cc7db6c294d73393a894 and the new function takes a
gendisk* as its argument, no longer a block_device*. Thus, bdev->bd_disk
is now used to pass the expected data.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#15060
This change was introduced in Linux commit
7ba150834b840f6f5cdd07ca69a4ccf39df59a66
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#15059
Make the version here match that elsewhere in the kernel and system
headers.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#15058
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
As it turns out having autotrim default to 'on' on FreeBSD never really
worked due to mess with defines where userland and kernel module were
getting different default values (userland was defaulting to 'off',
module was thinking it's 'on').
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Yuri Pankov <yuripv@FreeBSD.org>
Closes#15079
- Pack struct zio_prop by 4 bytes from 84 to 80.
- Skip new child ZIO locking while linking to parent. The newly
allocated ZIO is not externally visible yet, so nobody should care.
- Skip io_bp_copy writes when not used (write && non-debug).
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14985
Scan process may skip blocks based on their birth time, DVA, etc.
Traditionally those blocks were accounted as issued, that caused
reporting of hugely over-inflated numbers, having nothing to do
with actual disk I/O. This change utilizes never used field in
struct dsl_scan_phys to account such skipped bytes, allowing to
report how much data were actually scrubbed/resilvered and what
is the actual I/O speed. While formally it is an on-disk format
change, it should be compatible both ways, so should not need a
feature flag.
This should partially address the same issue as c85ac731a0, but
from a different perspective, complementing it.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Akash B <akash-b@hpe.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#15007
Consistently get the proper default value for autotrim.
Currently, only the kernel module is built with IN_FREEBSD_BASE,
and libzfs get the wrong default value, leading to confusion and
incorrect output when autotrim value was not set explicitly.
Reviewed-by: Warner Losh <imp@bsdimp.com>
Signed-off-by: Yuri Pankov <yuripv@FreeBSD.org>
Closes#15016
Switch FIFO queues (SYNC/TRIM) and active queue of vdev queue from
time-sorted AVL-trees to simple lists. AVL-trees are too expensive
for such a simple task. To change I/O priority without searching
through the trees, add io_queue_state field to struct zio.
To not check number of queued I/Os for each priority add vq_cqueued
bitmap to struct vdev_queue. Update it when adding/removing I/Os.
Make vq_cactive a separate array instead of struct vdev_queue_class
member. Together those allow to avoid lots of cache misses when
looking for work in vdev_queue_class_to_issue().
Introduce deadline of ~0.5s for LBA-sorted queues. Before this I
saw some I/Os waiting in a queue for up to 8 seconds and possibly
more due to starvation. With this change I no longer see it. I
had to slightly more complicate the comparison function, but since
it uses all the same cache lines the difference is minimal. For a
sequential I/Os the new code in vdev_queue_io_to_issue() actually
often uses more simple avl_first(), falling back to avl_find() and
avl_nearest() only when needed.
Arrange members in struct zio to access only one cache line when
searching through vdev queues. While there, remove io_alloc_node,
reusing the io_queue_node instead. Those two are never used same
time.
Remove zfs_vdev_aggregate_trim parameter. It was disabled for 4
years since implemented, while still wasted time maintaining the
offset-sorted tree of TRIM requests. Just remove the tree.
Remove locking from txg_all_lists_empty(). It is racy by design,
while 2 pair of locks/unlocks take noticeable time under the vdev
queue lock.
With these changes in my tests with volblocksize=4KB I measure vdev
queue lock spin time reduction by 50% on read and 75% on write.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14925
It's been observed that in certain workloads (zvol-related being a
big one), ZFS will end up spending a large amount of time spinning
up taskqs only to tear them down again almost immediately, then
spin them up again...
I noticed this when I looked at what my mostly-idle system was doing
and wondered how on earth taskq creation/destroy was a bunch of time...
So I added a configurable delay to avoid it tearing down tasks the
first time it notices them idle, and the total number of threads at
steady state went up, but the amount of time being burned just
tearing down/turning up new ones almost vanished.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#14938
Those callbacks were introduced many years ago as part of a bigger
patch to smoothen the write throttling within a txg. They allow to
account completion of individual physical writes within a logical
one, improving cases when some of physical writes complete much
sooner than others, gradually opening the write throttle.
Few years after that ZFS got allocation throttling, working on a
level of logical writes and limiting number of writes queued to
vdevs at any point, and so limiting latency distribution between
the physical writes and especially writes of multiple copies.
The addition of scheduling deadline I proposed in #14925 should
further reduce the latency distribution. Grown memory sizes over
the past 10 years should also reduce importance of the smoothing.
While the use of physdone callback may still in theory provide
some smoother throttling, there are cases where we simply can not
afford it. Since dirty data accounting is protected by pool-wide
lock, in case of 6-wide RAIDZ, for example, it requires us to take
it 8 times per logical block write, creating huge lock contention.
My tests of this patch show radical reduction of the lock spinning
time on workloads when smaller blocks are written to RAIDZ pools,
when each of the disks receives 8-16KB chunks, but the total rate
reaching 100K+ blocks per second. Same time attempts to measure
any write time fluctuations didn't show anything noticeable.
While there, remove also io_child_count/io_parent_count counters.
They are used only for couple assertions that can be avoided.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14948
With large number of tracked references list searches under the lock
become too expensive, creating enormous lock contention.
On my tests with ZFS_DEBUG enabled this increases write throughput
with 32KB blocks from ~1.2GB/s to ~7.5GB/s.
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14970
It was a vdev level read cache, designed to aggregate many small
reads by speculatively issuing bigger reads instead and caching
the result. But since it has almost no idea about what is going
on with exception of ZIO_FLAG_DONT_CACHE flag set by higher layers,
it was found to make more harm than good, for which reason it was
disabled for the past 12 years. These days we have much better
instruments to enlarge the I/Os, such as speculative and prescient
prefetches, I/O scheduler, I/O aggregation etc.
Besides just the dead code removal this removes one extra mutex
lock/unlock per write inside vdev_cache_write(), not otherwise
disabled and trying to do some work.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14953
There's no particular reason this function should be kernel-only, and I
want to use it (indirectly) from zdb. I've moved it to zfs_znode.c
because libzpool does not compile in zfs_vfsops.c, and this at least
matches the header its imported from.
Sponsored-By: Klara, Inc.
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: WHR <msl0000023508@gmail.com>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Closes#14642
There are two places where we need to add/remove several references
with semantics of zfs_refcount_(add|remove). But when debug/tracing
is disabled, it is a crime to run multiple atomic_inc() in a loop,
especially under congested pool-wide allocator lock.
Introduced new functions implement the same semantics as the loop,
but without overhead in production builds.
Reviewed-by: Rich Ercolani <rincebrain@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14934
This implements a binary search algorithm for B-Trees that reduces
branching to the absolute minimum necessary for a binary search
algorithm. It also enables the compiler to inline the comparator to
ensure that the only slowdown when doing binary search is from waiting
for memory accesses. Additionally, it instructs the compiler to unroll
the loop, which gives an additional 40% improve with Clang and 8%
improvement with GCC.
Consumers must opt into using the faster algorithm. At present, only
B-Trees used inside kernel code have been modified to use the faster
algorithm.
Micro-benchmarks suggest that this can improve binary search performance
by up to 3.5 times when compiling with Clang 16 and up to 1.9 times when
compiling with GCC 12.2.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14866
In addition to a number of actual log bytes written, account also a
total written bytes including padding and total allocated bytes (bytes
<= write <= alloc). It should allow to monitor zil traffic and space
efficiency.
Add dtrace probe for zil block size selection.
Make zilstat report more information and fit it into less width.
Reviewed-by: Ameer Hamza <ahamza@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14863
Before this change ZIL copied all log data while holding the lock.
It caused huge lock contention on workloads with many big parallel
writes. This change splits the process into two parts: first,
zil_lwb_assign() estimates the log space needed for all transactions,
and zil_lwb_write_close() allocates blocks and zios while holding the
lock, then, after the lock in dropped, zil_lwb_commit() copies the
data, and zil_lwb_write_issue() issues the I/Os.
Also while there slightly reduce scope of zl_lock.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Prakash Surya <prakash.surya@delphix.com>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14841
Added a flag '-e' in zpool scrub to scrub only blocks in error log. A
user can pause, resume and cancel the error scrub by passing additional
command line arguments -p -s just like a regular scrub. This involves
adding a new flag, creating new libzfs interfaces, a new ioctl, and the
actual iteration and read-issuing logic. Error scrubbing is executed in
multiple txg to make sure pool performance is not affected.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Co-authored-by: TulsiJain tulsi.jain@delphix.com
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#8995Closes#12355
zpool initialize functions well for touching every free byte...once.
But if we want to do it again, we're currently out of luck.
So let's add zpool initialize -u to clear it.
Co-authored-by: Rich Ercolani <rincebrain@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12451Closes#14873
The dmu_buf_is_dirty() call doesn't make sense here for two reasons:
1. txg is 0 for unassigned tx, so it was a no-op.
2. It is equivalent of checking if we have dirty records and we are doing
this few lines earlier.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Pawel Jakub Dawidek <pawel@dawidek.net>
Closes#14825
I don't know an easy way to shrink down dbuf size, so just deny block cloning
into dbufs that don't match our BP's size.
This fixes the following situation:
1. Create a small file, eg. 1kB of random bytes. Its dbuf will be 1kB.
2. Create a larger file, eg. 2kB of random bytes. Its dbuf will be 2kB.
3. Truncate the large file to 0. Its dbuf will remain 2kB.
4. Clone the small file into the large file. Small file's BP lsize is
1kB, but the large file's dbuf is 2kB.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Pawel Jakub Dawidek <pawel@dawidek.net>
Closes#14825
Reimplement some of the block cloning vs dbuf logic, mostly to fix
situation where we clone a block and in the same transaction group
we want to partially overwrite the clone.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Pawel Jakub Dawidek <pawel@dawidek.net>
Closes#14825
Provides an interface which callers can use to declare a write when
the exact starting offset in not yet known. Since the full range
being updated is not available only the first L0 block at the
provided offset will be prefetched.
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#14819
In case check_filesystem() does not error out and does not report
an error, remove that error block from error lists and logs
without requiring a scrub. This can happen when the original file and
all snapshots/clones referencing it have been removed.
Otherwise zpool status will still report that "Permanent errors have
been detected..." without actually reporting any of them.
To implement this change the functions introduced in corrective
receive were modified to take into account the head_errlog feature.
Before this change:
=============================
pool: test
state: ONLINE
status: One or more devices has experienced an error resulting in data
corruption. Applications may be affected.
action: Restore the file in question if possible. Otherwise restore the
entire pool from backup.
see: https://openzfs.github.io/openzfs-docs/msg/ZFS-8000-8A
config:
NAME STATE READ WRITE CKSUM
test ONLINE 0 0 0
/home/user/vdev_a ONLINE 0 0 2
errors: Permanent errors have been detected in the following files:
=============================
After this change:
=============================
pool: test
state: ONLINE
status: One or more devices has experienced an unrecoverable error. An
attempt was made to correct the error. Applications are
unaffected.
action: Determine if the device needs to be replaced, and clear the
errors
using 'zpool clear' or replace the device with 'zpool replace'.
see: https://openzfs.github.io/openzfs-docs/msg/ZFS-8000-9P
config:
NAME STATE READ WRITE CKSUM
test ONLINE 0 0 0
/home/user/vdev_a ONLINE 0 0 2
errors: No known data errors
=============================
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#14813
If a block pointer is corrupted (but the block containing it checksums
correctly, e.g. due to a bug that overwrites random memory), we can
often detect it before the block is read, with the `zfs_blkptr_verify()`
function, which is used in `arc_read()`, `zio_free()`, etc.
However, such corruption is not typically recoverable. To recover from
it we would need to detect the memory error before the block pointer is
written to disk.
This PR verifies BP's that are contained in indirect blocks and dnodes
before they are written to disk, in `dbuf_write_ready()`. This way,
we'll get a panic before the on-disk data is corrupted. This will help
us to diagnose what's causing the corruption, as well as being much
easier to recover from.
To minimize performance impact, only checks that can be done without
holding the spa_config_lock are performed.
Additionally, when corruption is detected, the raw words of the block
pointer are logged. (Note that `dprintf_bp()` is a no-op by default,
but if enabled it is not safe to use with invalid block pointers.)
Reviewed-by: Rich Ercolani <rincebrain@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Paul Zuchowski <pzuchowski@datto.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#14817
Clang specific pragmas need to be wrapped to prevent a build
warning when compiling with gcc.
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#14814
FreeBSD/powerpc64 is all ELFv2 since FreeBSD 13, even big endian. The
existing sha256 and sha512 asm code assumes that BE is all ELFv1, and LE
is ELFv2. Minor changes to add ELFv2 in the BE side gets this working
correctly on FreeBSD with latest OpenZFS import.
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Justin Hibbits <chmeeedalf@gmail.com>
Closes#14779
This reverts commit 4c856fb333 to
resolve a newly introduced deadlock which in practice in more
disruptive that the issue this commit intended to address.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #14775Closes#14790
Add loongarch64 definitions & lua module setjmp asm
LoongArch is a new RISC ISA, which is a bit like MIPS or RISC-V.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Han Gao <gaohan@uniontech.com>
Signed-off-by: WANG Xuerui <xen0n@gentoo.org>
Closes#13422
Usage:
zpool set org.freebsd:comment="this is my pool" poolname
Tests are based on zfs_set's user property tests.
Also stop truncating property values at MAXNAMELEN, use ZFS_MAXPROPLEN.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Mateusz Piotrowski <mateusz.piotrowski@klarasystems.com>
Sponsored-by: Beckhoff Automation GmbH & Co. KG.
Sponsored-by: Klara Inc.
Closes#11680
Clang points out that there is a comparison against -1, but we cannot
fix it because that is from the kernel headers, which we must support.
We can workaround this by using a pragma.
Sponsored-By: Wasabi Technology, Inc.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Youzhong Yang <yyang@mathworks.com>
Signed-off-by: Richard Yao <richard.yao@klarasystems.com>
Closes#14738
And add it to the AVZ, this is not backwards compatible with older pools
due to an assertion in spa_sync() that verifies the number of ZAPs of
all vdevs matches the number of ZAPs in the AVZ.
Granted, the assertion only applies to #DEBUG builds - still, a feature
flag is introduced to avoid the assertion, com.klarasystems:vdev_zaps_v2
Notably, this allows to get/set properties on the root vdev:
% zpool set user:prop=value <pool> root-0
Before this commit, it was already possible to get/set properties on
top-level vdevs with the syntax <type>-<vdev_id> (e.g. mirror-0):
% zpool set user:prop=value <pool> mirror-0
This syntax also applies to the root vdev as it is is of type 'root'
with a vdev_id of 0, root-0. The keyword 'root' as an alias for
'root-0'.
The following tests have been added:
- zpool get all properties from root vdev
- zpool set a property on root vdev
- verify root vdev ZAP is created
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Wing <rob.wing@klarasystems.com>
Sponsored-by: Seagate Technology
Submitted-by: Klara, Inc.
Closes#14405
At our site we have seen cases when multi-modifier protection is enabled
(multihost=on) on our pool and the pool gets suspended due to a single
disk that is failing and responding very slowly. Our pools have 90 disks
in them and we expect disks to fail. The current version of MMP requires
that we wait for other writers before moving on. When a disk is
responding very slowly, we observed that waiting here was bad enough to
cause the pool to suspend. This change allows the MMP thread to bypass
waiting for other threads and reduces the chances the pool gets
suspended.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Herb Wartens <hawartens@gmail.com>
Closes#14659
Spare vdev should detach from the pool when a disk is reinserted.
However, spare detachment depends on the completion of resilvering,
and if resilver does not schedule, the spare vdev keeps attached to
the pool until the next resilvering. When a zfs pool contains
several disks (25+ mirror), resilvering does not always happen when
a disk is reinserted. In this patch, spare vdev is manually detached
from the pool when resilvering does not occur and it has been tested
on both Linux and FreeBSD.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#14722
Add a new union member of flexible array to dnode_phys_t and use
it in the macro so we can silence the memcpy() fortify error.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Youzhong Yang <yyang@mathworks.com>
Closes#14737
Linux kernel 6.3 changed a bunch of APIs to use the dedicated idmap
type for mounts (struct mnt_idmap), we need to detect these changes
and make zfs work with the new APIs.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Youzhong Yang <yyang@mathworks.com>
Closes#14682
Just like x86, aarch64 needs to use the fpu_kern(9) API around FPU
usage, otherwise we panic promptly at boot as soon as ZFS attempts to
do checksum benchmarking.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Signed-off-by: Kyle Evans <kevans@FreeBSD.org>
Closes#14715
f6a0dac84 modified the zfs_iter_* functions to take a new "flags"
parameter, and introduced a variety of flags to ask the kernel to limit
the results in various ways, reducing the amount of work the caller
needed to do to filter out things they didn't need.
Unfortunately this change broke the ABI for existing clients (read:
older versions of the `zfs` program), and was reverted 399b98198.
dc95911d2 reintroduced the original patch, with the understanding that a
backwards-compatible fix would be made before the 2.2 release branch was
tagged. This commit is that fix.
This introduces zfs_iter_*_v2 functions that have the new flags
argument, and reverts the existing functions to not have the flags
parameter, as they were before. The old functions are now reimplemented
in terms of the new, with flags set to 0.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Wilson <george.wilson@delphix.com>
Original-patch-by: George Wilson <george.wilson@delphix.com>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Sponsored-by: Klara, Inc.
Closes#14597
Add missing machine/md_var.h to spl/sys/simd_aarch64.h and
spl/sys/simd_arm.h
In spl/sys/simd_x86.h, PCB_FPUNOSAVE exists only on amd64, use PCB_NPXNOSAVE
on i386
In FreeBSD sys/elf_common.h redefines AT_UID and AT_GID on FreeBSD, we need
a hack in vnode.h similar to Linux. sys/simd.h needs to be included early.
In zfs_freebsd_copy_file_range() we pass a (size_t *)lenp to
zfs_clone_range() that expects a (uint64_t *)
Allow compiling armv6 world by limiting ARM macros in sha256_impl.c and
sha512_impl.c to __ARM_ARCH > 6
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Pawel Jakub Dawidek <pawel@dawidek.net>
Reviewed-by: Signed-off-by: WHR <msl0000023508@gmail.com>
Signed-off-by: Martin Matuska <mm@FreeBSD.org>
Closes#14674
Running `zfs list -o avail rpool` resulted in a core dump.
This commit will fix this.
Run the needed overhead only, when `use_color()` is true.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Wilson <gwilson@delphix.com>
Signed-off-by: Tino Reichardt <milky-zfs@mcmilk.de>
Closes#14712
Modify bio_set_flush() so if kernel version is >= 4.10, flags
REQ_PREFLUSH and REQ_OP_WRITE are set together.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Youzhong Yang <yyang@mathworks.com>
Closes#14695
Address the following bugs in persistent error log:
1) Check nested clones, eg "fs->snap->clone->snap2->clone2".
2) When deleting files containing error blocks in those clones (from
"clone" the example above), do not break the check chain.
3) When deleting files in the originating fs before syncing the errlog
to disk, do not break the check chain. This happens because at the
time of introducing the error block in the error list, we do not have
its birth txg and the head filesystem. If the original file is
deleted before the error list is synced to the error log (which is
when we actually lookup the birth txg and the head filesystem), then
we do not have access to this info anymore and break the check chain.
The most prominent change is related to achieving (3). We expand the
spa_error_entry_t structure to accommodate the newly introduced
zbookmark_err_phys_t structure (containing the birth txg of the error
block).Due to compatibility reasons we cannot remove the
zbookmark_phys_t structure and we also need to place the new structure
after se_avl, so it is not accounted for in avl_find(). Then we modify
spa_log_error() to also provide the birth txg of the error block. With
these changes in place we simplify the previously introduced function
get_head_and_birth_txg() (now named get_head_ds()).
We chose not to follow the same approach for the head filesystem (thus
completely removing get_head_ds()) to avoid introducing new lock
contentions.
The stack sizes of nested functions (as measured by checkstack.pl in the
linux kernel) are:
check_filesystem [zfs]: 272 (was 912)
check_clones [zfs]: 64
We also introduced two new tests covering the above changes.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#14633
Current autotrim causes short-lived txg through:
1. calling txg_wait_synced() in metaslab_enable()
2. calling txg_wait_open() with should_quiesce = true
This patch addresses all the issues mentioned above.
A new cv, vdev_autotrim_kick_cv is added to kick autotrim activity.
It will be signaled once a txg is synced so that it does not change
the original autotrim pace. Also because it is a cv, the wait is
interruptible which speeds up the vdev_autotrim_stop_wait() call.
Finally, combining big zfs_txg_timeout, txg_wait_open() also causes
delay when exporting a pool.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: jxdking <lostking2008@hotmail.com>
Issue #8993Closes#12194
Linux 6.3+, and backports from it (6.2.8+), changed the
signatures on bdev_io_{start,end}_acct. Add a case for it.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#14658Closes#14668
This is probably the uncontroversial part of #13631, which fixes
a real problem people are having.
There's still things to improve in our code after this is merged,
but it should stop the breakage that people have reported, where
we lie about a type always being aligned and then pass in stack
objects with no alignment requirement and hope for the best.
Of course, our SIMD code was written with unaligned accesses, so it
doesn't care if we drop this...but some auto-vectorized code that
gcc emits sure does, since we told it it can assume they're aligned.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#14649
There is a window in the slog removal code where a panic loop could
ensue if the system crashes during that operation. The original design
of slog removal did not persisted any state because the removal happened
synchronously. This was changed by a later commit which persisted the
vdev_removing flag and exposed this bug. If a slog removal is in
progress and happens to crash after persisting the vdev_removing flag to
the label but before the vdev is removed from the spa config, then the
pool will continue to panic on import. Here's a sample of the panic:
[ 134.387411] VERIFY0(0 == dmu_buf_hold_array(os, object, offset, size,
FALSE, FTAG, &numbufs, &dbp)) failed (0 == 22)
[ 134.393865] PANIC at dmu.c:1135:dmu_write()
[ 134.396035] Kernel panic - not syncing: VERIFY0(0 ==
dmu_buf_hold_array(os, object, offset, size, FALSE, FTAG, &numbufs,
&dbp)) failed (0 == 22)
[ 134.397857] CPU: 2 PID: 5914 Comm: txg_sync Kdump: loaded Tainted:
P OE 5.4.0-1100-dx2023020205-b3751f8c2-azure #106
[ 134.407938] Hardware name: Microsoft Corporation Virtual
Machine/Virtual Machine, BIOS 090008 12/07/2018
[ 134.407938] Call Trace:
[ 134.407938] dump_stack+0x57/0x6d
[ 134.407938] panic+0xfb/0x2d7
[ 134.407938] spl_panic+0xcf/0x102 [spl]
[ 134.407938] ? traverse_impl+0x1ca/0x420 [zfs]
[ 134.407938] ? dmu_object_alloc_impl+0x3b4/0x3c0 [zfs]
[ 134.407938] ? dnode_hold+0x1b/0x20 [zfs]
[ 134.407938] dmu_write+0xc3/0xd0 [zfs]
[ 134.407938] ? space_map_alloc+0x55/0x80 [zfs]
[ 134.407938] metaslab_sync+0x61a/0x830 [zfs]
[ 134.407938] ? queued_spin_unlock+0x9/0x10 [zfs]
[ 134.407938] vdev_sync+0x72/0x190 [zfs]
[ 134.407938] spa_sync_iterate_to_convergence+0x160/0x250 [zfs]
[ 134.407938] spa_sync+0x2f7/0x670 [zfs]
[ 134.407938] txg_sync_thread+0x22d/0x2d0 [zfs]
[ 134.407938] ? txg_dispatch_callbacks+0xf0/0xf0 [zfs]
[ 134.407938] thread_generic_wrapper+0x83/0xa0 [spl]
[ 134.407938] kthread+0x104/0x140
[ 134.407938] ? kasan_check_write.constprop.0+0x10/0x10 [spl]
[ 134.407938] ? kthread_park+0x90/0x90
[ 134.457802] ret_from_fork+0x1f/0x40
This change no longer persists the vdev_removing flag when removing slog
devices and also cleans up some code that was added which is not used.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: George Wilson <gwilson@delphix.com>
Closes#14652
Undirty the dbuf and destroy its buffer when cloning into it.
Coverity ID: CID-1535375
Reported-by: Richard Yao
Reported-by: Benjamin Coddington
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Pawel Jakub Dawidek <pawel@dawidek.net>
Closes#14655
Commit 11913870 (#14567) added cmn_err_once() by #define'ing a
compound statement but failed to consider usage in a single
statement brace-less if else.
Fix the problem by using the common "do {} while (0)" construct.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Attila Fülöp <attila@fueloep.org>
Closes#14629
Commit 5401472 adds a check to call enable_kernel_spe and
disable_kernel_spe only if CONFIG_SPE is defined. Refactor this check
in a way similar to what CONFIG_ALTIVEC and CONFIG_VSX are checked, in
order to remove redundant kfpu_begin() and kfpu_end() implementations.
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: WHR <msl0000023508@gmail.com>
Closes#14623
This commit removes the edonr_byteorder.h file and all unused
variants of Edon-R.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tino Reichardt <milky-zfs@mcmilk.de>
Closes#13618
Coverity reported possible out-of-bounds reads from doing `((char
*)(nvp) + sizeof (nvpair_t))` to get the nvpair name string. These were
initially marked as false positives, but since we are now using C99
flexible array members elsewhere, we could use them here too as cleanup
to make the code easier to understand.
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reported-by: Coverity (CID-977165)
Reported-by: Coverity (CID-1524109)
Reported-by: Coverity (CID-1524642)
Closes#14612
After addressing coverity complaints involving `nvpair_name()`, the
compiler started complaining about dropping const. This lead to a rabbit
hole where not only `nvpair_name()` needed to be constified, but also
`nvpair_value_string()`, `fnvpair_value_string()` and a few other static
functions, plus variable pointers throughout the code. The result became
a fairly big change, so it has been split out into its own patch.
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14612
Clang's static analyzer complains that nvs_xdr() and nvs_native()
functions return pointers to stack memory. That is technically true, but
the pointers are stored in stack memory from the caller's stack frame,
are not read by the caller and are deallocated when the caller returns,
so this is harmless. We set the pointers to NULL to silence the
warnings.
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14612
The commit replaces all findings of the link:
http://www.opensolaris.org/os/licensing with this one:
https://opensource.org/licenses/CDDL-1.0
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: WHR <msl0000023508@gmail.com>
Signed-off-by: Tino Reichardt <milky-zfs@mcmilk.de>
Closes#14625
Currently calls to kfpu_begin() and kfpu_end() are split between
the init() and fini() functions of the particular SIMD
implementation. This was done in #14247 as an optimization measure
for the ABD adapter. Unfortunately the split complicates FPU
handling on platforms that use a local FPU state buffer, like
Windows and macOS.
To ease porting, we introduce a boolean struct member in
fletcher_4_ops_t, indicating use of the FPU, and move the FPU state
handling from the SIMD implementations to the call sites.
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Signed-off-by: Attila Fülöp <attila@fueloep.org>
Closes#14600
Block Cloning allows to manually clone a file (or a subset of its
blocks) into another (or the same) file by just creating additional
references to the data blocks without copying the data itself.
Those references are kept in the Block Reference Tables (BRTs).
The whole design of block cloning is documented in module/zfs/brt.c.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Christian Schwarz <christian.schwarz@nutanix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Rich Ercolani <rincebrain@gmail.com>
Signed-off-by: Pawel Jakub Dawidek <pawel@dawidek.net>
Closes#13392
Linux since 4.7 makes interface 'cpu_has_feature' to use jump labels on
powerpc if CONFIG_JUMP_LABEL_FEATURE_CHECKS is enabled, in this case
however the inline function references GPL-only symbol
'cpu_feature_keys'.
ZFS currently uses 'cpu_has_feature' either directly or indirectly from
several places; while it is unknown how this issue didn't break ZFS on
64-bit little-endian powerpc, it is known to break ZFS with many Linux
versions on both 32-bit and 64-bit big-endian powerpc.
Until this issue is fixed in Linux, we have to workaround it by
overriding affected inline functions without depending on
'cpu_feature_keys'.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: WHR <msl0000023508@gmail.com>
Closes#14590
Clang's static analyzer pointed out that if we can pass a -1 array index
to copyname[copies] if there are no valid DVAs. This is an absurd
situation, but it suggests that we are missing an assertion, so we add
it.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14575
Traditionally ARC adaptation was limited to MRU/MFU distribution. But
for years people with metadata-centric workload demanded mechanisms to
also manage data/metadata distribution, that in original ZFS was just
a FIFO. As result ZFS effectively got separate states for data and
metadata, minimum and maximum metadata limits etc, but it all required
manual tuning, was not adaptive and in its heart remained a bad FIFO.
This change removes most of existing eviction logic, rewriting it from
scratch. This makes MRU/MFU adaptation individual for data and meta-
data, same as the distribution between data and metadata themselves.
Since most of required states separation was already done, it only
required to make arcs_size state field specific per data/metadata.
The adaptation logic is still based on previous concept of ghost hits,
just now it balances ARC capacity between 4 states: MRU data, MRU
metadata, MFU data and MFU metadata. To simplify arc_c changes instead
of arc_p measured in bytes, this code uses 3 variable arc_meta, arc_pd
and arc_pm, representing ARC balance between metadata and data, MRU and
MFU for data, and MRU and MFU for metadata respectively as 32-bit fixed
point fractions. Since we care about the math result only when need to
evict, this moves all the logic from arc_adapt() to arc_evict(), that
reduces per-block overhead, since per-block operations are limited to
stats collection, now moved from arc_adapt() to arc_access() and using
cheaper wmsums. This also allows to remove ugly ARC_HDR_DO_ADAPT flag
from many places.
This change also removes number of metadata specific tunables, part of
which were actually not functioning correctly, since not all metadata
are equal and some (like L2ARC headers) are not really evictable.
Instead it introduced single opaque knob zfs_arc_meta_balance, tuning
ARC's reaction on ghost hits, allowing administrator give more or less
preference to metadata without setting strict limits.
Some of old code parts like arc_evict_meta() are just removed, because
since introduction of ABD ARC they really make no sense: only headers
referenced by small number of buffers are not evictable, and they are
really not evictable no matter what this code do. Instead just call
arc_prune_async() if too much metadata appear not evictable.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14359
This fixes building ZFS for Linux 4.7+ powerpc* architecture, where
Linux was configured without CONFIG_ALTIVEC or CONFIG_VSX.
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: WHR <msl0000023508@gmail.com>
Closes#14591
The intent is that this is like ENOTSUP, but specifically for when
something can't be done because we have no support for the requested
crypto parameters; eg unlocking a dataset or receiving a stream
encrypted with a suite we don't support.
Its not intended to be recoverable without upgrading ZFS itself.
If the request could be made to work by enabling a feature or modifying
some other configuration item, then some other code should be used.
load-key: In the future we might have more crypto suites (ie new values
for the `encryption` property. Right now trying to load a key on such
a future crypto suite will look up suite parameters off the end of the
crypto table, resulting in misbehaviour and/or crashes (or, with debug
enabled, trip the assertion in `zio_crypt_key_unwrap`).
Instead, lets check the value we got from the dataset, and if we can't
handle it, abort early.
recv: When receiving a raw stream encrypted with an unknown crypto
suite, `zfs recv` would report a generic `invalid backup stream`
(EINVAL). While technically correct, its not super helpful, so lets
ship a more specific error code and message.
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Rob Norris <robn@despairlabs.com>
Closes#14577
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Attila Fülöp <attila@fueloep.org>
Closes#14567
This commit changes the BLAKE3 implementation handling and
also the calls to it from the ztest command.
Tested-by: Rich Ercolani <rincebrain@gmail.com>
Tested-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tino Reichardt <milky-zfs@mcmilk.de>
Closes#13741
The skeleton file module/icp/include/generic_impl.c can be used for
iterating over different implementations of algorithms.
It is used by SHA256, SHA512 and BLAKE3 currently.
The Solaris SHA2 implementation got replaced with a version which is
based on public domain code of cppcrypto v0.10.
These assembly files are taken from current openssl master:
- sha256-x86_64.S: x64, SSSE3, AVX, AVX2, SHA-NI (x86_64)
- sha512-x86_64.S: x64, AVX, AVX2 (x86_64)
- sha256-armv7.S: ARMv7, NEON, ARMv8-CE (arm)
- sha512-armv7.S: ARMv7, NEON (arm)
- sha256-armv8.S: ARMv7, NEON, ARMv8-CE (aarch64)
- sha512-armv8.S: ARMv7, ARMv8-CE (aarch64)
- sha256-ppc.S: Generic PPC64 LE/BE (ppc64)
- sha512-ppc.S: Generic PPC64 LE/BE (ppc64)
- sha256-p8.S: Power8 ISA Version 2.07 LE/BE (ppc64)
- sha512-p8.S: Power8 ISA Version 2.07 LE/BE (ppc64)
Tested-by: Rich Ercolani <rincebrain@gmail.com>
Tested-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tino Reichardt <milky-zfs@mcmilk.de>
Closes#13741
These are added:
- zfs_neon_available() for arm and aarch64
- zfs_sha256_available() for arm and aarch64
- zfs_sha512_available() for aarch64
- zfs_shani_available() for x86_64
Tested-by: Rich Ercolani <rincebrain@gmail.com>
Tested-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tino Reichardt <milky-zfs@mcmilk.de>
Co-Authored-By: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Closes#13741
These are added:
- zfs_neon_available() for arm and aarch64
- zfs_sha256_available() for arm and aarch64
- zfs_sha512_available() for aarch64
- zfs_shani_available() for x86_64
Changes:
- simd_powerpc.h: change license from CDDL to BSD
Tested-by: Rich Ercolani <rincebrain@gmail.com>
Tested-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tino Reichardt <milky-zfs@mcmilk.de>
Closes#13741
We had three sha2.h headers in different places.
The FreeBSD version, the Linux version and the generic solaris version.
The only assembly used for acceleration was some old x86-64 openssl
implementation for sha256 within the icp module.
For FreeBSD the whole SHA2 files of FreeBSD were copied into OpenZFS,
these files got removed also.
Tested-by: Rich Ercolani <rincebrain@gmail.com>
Tested-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tino Reichardt <milky-zfs@mcmilk.de>
Closes#13741
With some pathological access patterns it is possible to make ZFS
accumulate almost unlimited amount of speculative prefetch ZIOs.
Combined with linear ABD allocations in RAIDZ code, it appears to
be possible to exhaust system KVA, triggering kernel panic.
Address this by introducing a system-wide counter of active prefetch
requests and blocking prefetch distance doubling per stream hits if
the number of active requests is higher that ~6% of ARC size.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14516
openzfsonwindows/openzfs#206 found that it is possible to trip
`VERIFY(list_is_empty(&lwb->lwb_itxs))` when a `zil_commit()` is delayed
by the scheduler long enough for a parallel `zil_suspend()` operation to
exit `zil_commit_impl()`. This is a data race. To prevent this, we
introduce a `zilog->zl_suspend_lock` rwlock to ensure that all
outstanding `zil_commit()` operations finish before `zil_suspend()`
begins and that subsequent operations fallback to `txg_wait_synced()`
after `zil_suspend()` has begun.
On `PREEMPT_RT` Linux kernels, the `rw_enter()` implementation suffers
from writer starvation. This means that a ZIL intensive system can delay
`zil_suspend()` indefinitely. This is a pre-existing problem that
affects everything that uses rw locks, so it needs to be addressed in
the SPL. However, builds against `PREEMPT_RT` Linux kernels are
currently broken due to a GPL symbol issue (#11097), so we can safely
disregard that issue for now.
Reported-by: Arun KV <arun.kv@datacore.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14514
A spurious mutex_exit() in a development branch caused weird issues
until I identified it. An assertion prior to mutex_exit() would have
caught it. Rather than adding assertions before invocations of
mutex_exit() in the code, let us simply add an assertion to
mutex_exit(). It is cheap and will likely improve developer
productivity.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Richard Yao <richard.yao@klarasystems.com>
Sponsored-By: Wasabi Technology, Inc.
Closes#14541
Commit 34ce4c4 made zfeature_active() non-static. This is not required.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#14546
Hole detection in the zio compression code allows us to
opportunistically skip compression on holes. We can go a step further
by not doing memory allocations on holes either.
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Richard Yao <richard.yao@klarasystems.com>
Sponsored-by: Wasabi Technology, Inc.
Closes#14500
In commit 0a5b942d4 the FreeBSD SECTION_STATIC macro was set to
".rodata". This assembler directive is supported by LLVM (as a
convenience alias for ".section .rodata") by not by GNU as.
This caused the FreeBSD builds that are done with gcc to fail.
Therefore, use ".section .rodata" instead, similar to the other
asm_linkage.h headers.
Reviewed-by: Mateusz Guzik <mjguzik@gmail.com>
Reviewed-by: Attila Fülöp <attila@fueloep.org>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Signed-off-by: Dimitry Andric <dimitry@andric.com>
Closes#14526
When a page is faulted in for memory mapped I/O the page lock
may be dropped before it has been read and marked up to date.
If a buffered read encounters such a page in mappedread() it
must wait until the page has been updated. Failure to do so
will result in a panic on debug builds and incorrect data on
production builds.
The critical part of this change is in mappedread() where pages
which are not up to date are now handled. Additionally, it
includes the following simplifications.
- zfs_getpage() and zfs_fillpage() could be passed an array of
pages. This could be more efficient if it was used but in
practice only a single page was ever provided. These
interfaces were simplified to acknowledge that.
- update_pages() was modified to correctly set the PG_error bit
on a page when it cannot be read by dmu_read().
- Setting PG_error and PG_uptodate was moved to zfs_fillpage()
from zpl_readpage_common(). This is consistent with the
handling in update_pages() and mappedread().
- Minor additional refactoring to comments and variable
declarations to improve readability.
- Add a test case to exercise concurrent buffered, direct,
and mmap IO to the same file.
- Reduce the mmap_sync test case default run time.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13608Closes#14498
Apply zero padding for checksums consistently. The SNPRINTF_BLKPTR
macro was not updated in commit ac7648179c which results in the
`cli_root/zdb/zdb_checksum.ksh` test case reliably failing.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Akash B <akash-b@hpe.com>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#14497
As of the 4.13 kernel filemap_range_has_page() can be used to
check if there is a page mapped in a given file range. When
available this interface should be used which eliminates the
need for the zp->z_is_mapped boolean.
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#14493
The zio returned from arc_write() in dmu_objset_sync() uses
zio_nowait(). However we may reach the end of dsl_dataset_sync()
which checks if we need to activate features in the filesystem
without knowing if that zio has even run through the ZIO pipeline yet.
In that case we will flag features to be activated in
dsl_dataset_block_born() but dsl_dataset_sync() has already
completed its run and those features will not actually be activated.
Mitigate this by moving the feature activation code in
dsl_dataset_sync_done(). Also add new ASSERTs in
dsl_scan_visitbp() checking if a block contradicts any filesystem
flags.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#13816
In https://github.com/openzfs/zfs/pull/14228 the FreeBSD
SECTION_STATIC was set to ".data" instead of ".rodata". This
commit just restores it back to .rodata.
Reviewed-by: Attila Fülöp <attila@fueloep.org>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Closes#14460
zfs_setproctitle_init() is stubbed out on FreeBSD.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Ameer Hamza <ahamza@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Rob Wing <rob.fx907@gmail.com>
Closes#14441
During snapshot deletion ZFS may issue several reads for each deadlist
to merge them into next snapshot's or pool's bpobj. Number of the dead
lists increases with number of snapshots. On HDD pools it may take
significant time during which sync thread is blocked.
This patch introduces prescient prefetch of required blocks for up to
128 deadlists ahead. Tests show reduction of time required to delete
dataset with 720 snapshots with randomly overwritten file on wide HDD
pool from 75-85 to 22-28 seconds.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Issue #14276Closes#14402
Linux 6.2 changes the second argument of the set_acl operation to be a
"struct dentry *" rather than a "struct inode *". The inode* parameter
is still available as dentry->d_inode, so adjust the call to the _impl
function call to dereference and pass that pointer to it.
Also document that the get_acl -> get_inode_acl member name change from
commit 884a693 was an API change also introduced in Linux 6.2.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#14415
The .align directive used to align storage locations is
ambiguous. On some platforms and assemblers it takes a byte count,
on others the argument is interpreted as a shift value. The current
usage expects the first interpretation.
Replace it with the unambiguous .balign directive which always
expects a byte count, regardless of platform and assembler.
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Attila Fülöp <attila@fueloep.org>
Closes#14422
Introduce four new vdev properties:
checksum_n
checksum_t
io_n
io_t
These properties can be used for configuring the thresholds of zed's
diagnosis engine and are interpeted as <N> events in T <seconds>.
When this property is set to a non-default value on a top-level vdev,
those thresholds will also apply to its leaf vdevs. This behavior can be
overridden by explicitly setting the property on the leaf vdev.
Note that, these properties do not persist across vdev replacement. For
this reason, it is advisable to set the property on the top-level vdev
instead of the leaf vdev.
The default values for zed's diagnosis engine (10 events, 600 seconds)
remains unchanged.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Rob Wing <rob.wing@klarasystems.com>
Sponsored-by: Seagate Technology LLC
Closes#13805
This is only ever used with unsigned data, so the type itself should be
unsigned. Also, PVS Studio's 2016 FreeBSD kernel report correctly
identified the following assertion as always being true, so we can drop
it:
ASSERT3U(dd->dd_space_towrite[i & TXG_MASK], >=, 0);
The reason it was always true is because it would do casts to give us
unsigned comparisons. This could have been fixed by switching to
`ASSERT3S()`, but upon inspection, it turned out that this variable
never should have been allowed to be signed in the first place.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14408
In original code, zfs_znode_dmu_fini is called in zfs_rmnode without
zfs_znode_hold_enter. It seems to assume it's ok to do so when the znode
is unlinked. However this assumption is not correct, as zfs_zget can be
called by NFS through zpl_fh_to_dentry as pointed out by Christian in
https://github.com/openzfs/zfs/pull/12767, which could result in a
use-after-free bug.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Chunwei Chen <david.chen@nutanix.com>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#12767Closes#14364
Add new macro ASMABI used by Windows to change
calling API to "sysv_abi".
Reviewed-by: Attila Fülöp <attila@fueloep.org>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Closes#14228
This allows parsing of zfs send progress by checking the process
title.
Doing so requires some changes to the send code in libzfs_sendrecv.c;
primarily these changes move some of the accounting around, to allow
for the code to be verbose as normal, or set the process title. Unlike
BSD, setproctitle() isn't standard in Linux; thus, borrowed it from
libbsd with slight modifications.
Authored-by: Sean Eric Fagan <sef@FreeBSD.org>
Co-authored-by: Ryan Moeller <ryan@iXsystems.com>
Co-authored-by: Ameer Hamza <ahamza@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#14376
I recently gained the ability to run Clang's static analyzer on the
linux kernel modules via a few hacks. This extended coverage to code
that was previously missed since Clang's static analyzer only looked at
code that we built in userspace. Running it against the Linux kernel
modules built from my local branch produced a total of 72 reports
against my local branch. Of those, 50 were reports of logic errors and
22 were reports of dead code. Since we already had cleaned up all of
the previous dead code reports, I felt it would be a good next step to
clean up these dead code reports. Clang did a further breakdown of the
dead code reports into:
Dead assignment 15
Dead increment 2
Dead nested assignment 5
The benefit of cleaning these up, especially in the case of dead nested
assignment, is that they can expose places where our error handling is
incorrect. A number of them were fairly straight forward. However
several were not:
In vdev_disk_physio_completion(), not only were we not using the return
value from the static function vdev_disk_dio_put(), but nothing used it,
so I changed it to return void and removed the existing (void) cast in
the other area where we call it in addition to no longer storing it to a
stack value.
In FSE_createDTable(), the function is dead code. Its helper function
FSE_freeDTable() is also dead code, as are the CPP definitions in
`module/zstd/include/zstd_compat_wrapper.h`. We just delete it all.
In zfs_zevent_wait(), we have an optimization opportunity. cv_wait_sig()
returns 0 if there are waiting signals and 1 if there are none. The
Linux SPL version literally returns `signal_pending(current) ? 0 : 1)`
and FreeBSD implements the same semantics, we can just do
`!cv_wait_sig()` in place of `signal_pending(current)` to avoid
unnecessarily calling it again.
zfs_setattr() on FreeBSD version did not have error handling issue
because the code was removed entirely from FreeBSD version. The error is
from updating the attribute directory's files. After some thought, I
decided to propapage errors on it to userspace.
In zfs_secpolicy_tmp_snapshot(), we ignore a lack of permission from the
first check in favor of checking three other permissions. I assume this
is intentional.
In zfs_create_fs(), the return value of zap_update() was not checked
despite setting an important version number. I see no backward
compatibility reason to permit failures, so we add an assertion to catch
failures. Interestingly, Linux is still using ASSERT(error == 0) from
OpenSolaris while FreeBSD has switched to the improved ASSERT0(error)
from illumos, although illumos has yet to adopt it here. ASSERT(error ==
0) was used on Linux while ASSERT0(error) was used on FreeBSD since the
entire file needs conversion and that should be the subject of
another patch.
dnode_move()'s issue was caused by us not having implemented
POINTER_IS_VALID() on Linux. We have a stub in
`include/os/linux/spl/sys/kmem_cache.h` for it, when it really should be
in `include/os/linux/spl/sys/kmem.h` to be consistent with
Illumos/OpenSolaris. FreeBSD put both `POINTER_IS_VALID()` and
`POINTER_INVALIDATE()` in `include/os/freebsd/spl/sys/kmem.h`, so we
copy what it did.
Whenever a report was in platform-specific code, I checked the FreeBSD
version to see if it also applied to FreeBSD, but it was only relevant a
few times.
Lastly, the patch that enabled Clang's static analyzer to be run on the
Linux kernel modules needs more work before it can be put into a PR. I
plan to do that in the future as part of the on-going static analysis
work that I am doing.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14380
d_alias may need to be converted to du.d_alias
depending on the kernel version.
d_alias is currently in only one place in the code which
changes
"hlist_for_each_entry(dentry, &inode->i_dentry, d_alias)"
to
"hlist_for_each_entry(dentry, &inode->i_dentry, d_u.d_alias)"
as neccesary.
This effectively results in a double macro expansion
for code that uses the zfs headers but already has its
own macro for just d_alias (lustre in this case).
Remove the conditional code for hlist_for_each_entry
and have a macro for "d_alias -> du.d_alias" instead.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Gian-Carlo DeFazio <defazio1@llnl.gov>
Closes#14377
The Blocking Queue (bqueue) code is used by zfs send/receive to send
messages between the various threads. It uses a shared linked list,
which is locked whenever we enqueue or dequeue. For workloads which
process many blocks per second, the locking on the shared list can be
quite expensive.
This commit changes the bqueue logic to have 3 linked lists:
1. An enquing list, which is used only by the (single) enquing thread,
and thus needs no locks.
2. A shared list, with an associated lock.
3. A dequing list, which is used only by the (single) dequing thread,
and thus needs no locks.
The entire enquing list can be moved to the shared list in constant
time, and the entire shared list can be moved to the dequing list in
constant time. These operations only happen when the `fill_fraction` is
reached, or on an explicit flush request. Therefore, the lock only
needs to be acquired infrequently.
The API already allows for dequing to block until an explicit flush, so
callers don't need to be changed.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Wilson <george.wilson@delphix.com>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#14121
