ZFS works best when it is notified as soon as possible when a device
failure occurs. This allows it to immediately start any recovery
actions which may be needed. In theory Linux supports a flag which
can be set on bio's called FAILFAST which provides this quick
notification by disabling the retry logic in the lower scsi layers.
That's the theory at least. In practice is turns out that while the
flag exists you oddly have to set it with the BIO_RW_AHEAD flag.
And even when it's set it you may get retries in the low level
drivers decides that's the right behavior, or if you don't get the
right error codes reported to the scsi midlayer.
Unfortunately, without additional kernels patchs there's not much
which can be done to improve this. Basically, this just means that
it may take 2-3 minutes before a ZFS is notified properly that a
device has failed. This can be improved and I suspect I'll be
submitting patches upstream to handle this.
By default the Solaris code does not log speculative or soft io errors
in either 'zpool status' or post an event. Under Linux we don't want
to change the expected behavior of 'zpool status' so these io errors
are still suppressed there.
However, since we do need to know about these events for Linux FMA and
the 'zpool events' interface is new we do post the events. With the
addition of the zio_flags field the posted events now contain enough
information that a user space consumer can identify and discard these
events if it sees fit.
All the upper layers of zfs expect zio->io_error to be positive. I was
careful but I missed one instance in vdev_disk_physio_completion() which
could return a negative error. To ensure all cases are always caught I
had additionally added an ASSERT() to check this before zio_interpret().
Finally, as a debugging aid when zfs is build with --enable-debug all
errors from the backing block devices will be reported to the console
with an error message like this:
ZFS: zio error=5 type=1 offset=4217856 size=8192 flags=60440
Observed during failure mode testing, dsl_scan_setup_sync() allocates
73920 bytes. This is way over the limit of what is wise to do with a
kmem_alloc() and it should probably be moved to a slab. For now I'm
just flagging it with KM_NODEBUG to quiet the error until this can be
revisited.
This commit fixes a bug in vdev_disk_open() in which the whole_disk property
was getting set to 0 for disk devices, even when it was stored as a 1 when the
zpool was created. The whole_disk property lets us detect when the partition
suffix should be stripped from the device name in CLI output. It is also used
to determine how writeback cache should be set for a device.
When an existing zpool is imported its configuration is read from the vdev
label by user space in zpool_read_label(). The whole_disk property is saved in
the nvlist which gets passed into the kernel, where it in turn gets saved in
the vdev struct in vdev_alloc(). Therefore, this value is available in
vdev_disk_open() and should not be overridden by checking the provided device
path, since that path will likely point to a partition and the check will
return the wrong result.
We also add an ASSERT that the whole_disk property is set. We are not aware of
any cases where vdev_disk_open() should be called with a config that doesn't
have this property set. The ASSERT is there so that when debugging is enabled
we can identify any legitimate cases that we are missing. If we never hit the
ASSERT, we can at some point remove it along with the conditional whole_disk
check.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
This callback is needed for properly accounting the per-uid and per-gid
space usage. Even if we don't have the ZPL, we still need this callback
in order to have proper on-disk ZPL compatibility and to be able to use
Lustre quotas.
Fortunately, the callback doesn't have any ZPL/VFS dependencies so we
can just move it out of #ifdef HAVE_ZPL.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Required for the DB_DNODE_ENTER()/DB_DNODE_EXIT() helpers.
Signed-off-by: Ricardo M. Correia <ricardo.correia@oracle.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
In my machine, dnode_hold_impl() allocates 9992 bytes in DEBUG mode and it
causes a large stream of stack traces in the logs. Instead, use KM_NODEBUG
to quiet down this known large alloc.
Signed-off-by: Ricardo M. Correia <ricardo.correia@oracle.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
One of the neat tricks an autoconf style project is capable of
is allow configurion/building in a directory other than the
source directory. The major advantage to this is that you can
build the project various different ways while making changes
in a single source tree.
For example, this project is designed to work on various different
Linux distributions each of which work slightly differently. This
means that changes need to verified on each of those supported
distributions perferably before the change is committed to the
public git repo.
Using nfs and custom build directories makes this much easier.
I now have a single source tree in nfs mounted on several different
systems each running a supported distribution. When I make a
change to the source base I suspect may break things I can
concurrently build from the same source on all the systems each
in their own subdirectory.
wget -c http://github.com/downloads/behlendorf/zfs/zfs-x.y.z.tar.gz
tar -xzf zfs-x.y.z.tar.gz
cd zfs-x-y-z
------------------------- run concurrently ----------------------
<ubuntu system> <fedora system> <debian system> <rhel6 system>
mkdir ubuntu mkdir fedora mkdir debian mkdir rhel6
cd ubuntu cd fedora cd debian cd rhel6
../configure ../configure ../configure ../configure
make make make make
make check make check make check make check
This change also moves many of the include headers from individual
incude/sys directories under the modules directory in to a single
top level include directory. This has the advantage of making
the build rules cleaner and logically it makes a bit more sense.
This topic branch contains all the changes needed to integrate the user
side zfs tools with Linux style devices. Primarily this includes fixing
up the Solaris libefi library to be Linux friendly, and integrating with
the libblkid library which is provided by e2fsprogs.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
The upstream ZFS code has correctly moved to a faster native sha2
implementation. Unfortunately, under Linux that's going to be a little
problematic so we revert the code to the more portable version contained
in earlier ZFS releases. Using the native sha2 implementation in Linux
is possible but the API is slightly different in kernel version user
space depending on which libraries are used. Ideally, we need a fast
implementation of SHA256 which builds as part of ZFS this shouldn't be
that hard to do but it will take some effort.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
This branch contains the majority of the changes required to cleanly
intergrate with Linux style special devices (/dev/zfs). Mainly this
means dropping all the Solaris style callbacks and replacing them
with the Linux equivilants.
This patch also adds the onexit infrastructure needed to track
some minimal state between ioctls. Under Linux it would be easy
to do this simply using the file->private_data. But under Solaris
they apparent need to pass the file descriptor as part of the ioctl
data and then perform a lookup in the kernel. Once again to keep
code change to a minimum I've implemented the Solaris solution.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
The ZFS update to onnv_141 brought with it support for a
security label attribute called mlslabel. This feature
depends on zones to work correctly and thus I am disabling
it under Linux. Equivilant functionality could be added
at some point in the future.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
This topic branch leverages the Solaris style FMA call points
in ZFS to create a user space visible event notification system
under Linux. This new system is called zevent and it unifies
all previous Solaris style ereports and sysevent notifications.
Under this Linux specific scheme when a sysevent or ereport event
occurs an nvlist describing the event is created which looks almost
exactly like a Solaris ereport. These events are queued up in the
kernel when they occur and conditionally logged to the console.
It is then up to a user space application to consume the events
and do whatever it likes with them.
To make this possible the existing /dev/zfs ABI has been extended
with two new ioctls which behave as follows.
* ZFS_IOC_EVENTS_NEXT
Get the next pending event. The kernel will keep track of the last
event consumed by the file descriptor and provide the next one if
available. If no new events are available the ioctl() will block
waiting for the next event. This ioctl may also be called in a
non-blocking mode by setting zc.zc_guid = ZEVENT_NONBLOCK. In the
non-blocking case if no events are available ENOENT will be returned.
It is possible that ESHUTDOWN will be returned if the ioctl() is
called while module unloading is in progress. And finally ENOMEM
may occur if the provided nvlist buffer is not large enough to
contain the entire event.
* ZFS_IOC_EVENTS_CLEAR
Clear are events queued by the kernel. The kernel will keep a fairly
large number of recent events queued, use this ioctl to clear the
in kernel list. This will effect all user space processes consuming
events.
The zpool command has been extended to use this events ABI with the
'events' subcommand. You may run 'zpool events -v' to output a
verbose log of all recent events. This is very similar to the
Solaris 'fmdump -ev' command with the key difference being it also
includes what would be considered sysevents under Solaris. You
may also run in follow mode with the '-f' option. To clear the
in kernel event queue use the '-c' option.
$ sudo cmd/zpool/zpool events -fv
TIME CLASS
May 13 2010 16:31:15.777711000 ereport.fs.zfs.config.sync
class = "ereport.fs.zfs.config.sync"
ena = 0x40982b7897700001
detector = (embedded nvlist)
version = 0x0
scheme = "zfs"
pool = 0xed976600de75dfa6
(end detector)
time = 0x4bec8bc3 0x2e5aed98
pool = "zpios"
pool_guid = 0xed976600de75dfa6
pool_context = 0x0
While the 'zpool events' command is handy for interactive debugging
it is not expected to be the primary consumer of zevents. This ABI
was primarily added to facilitate the addition of a user space
monitoring daemon. This daemon would consume all events posted by
the kernel and based on the type of event perform an action. For
most events simply forwarding them on to syslog is likely enough.
But this interface also cleanly allows for more sophisticated
actions to be taken such as generating an email for a failed drive.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Add autoconf style build infrastructure to the ZFS tree. This
includes autogen.sh, configure.ac, m4 macros, some scripts/*,
and makefiles for all the core ZFS components.
Due to limited stack space recursive functions are frowned upon in
the Linux kernel. However, they often are the most elegant solution
to a problem. The following code preserves the recursive function
traverse_visitbp() but moves the local variables AND function
arguments to the heap to minimize the stack frame size. Enough
space is initially allocated on the stack for 20 levels of recursion.
This change does ugly-up-the-code but it reduces the worst case
usage from roughly 4160 bytes to 960 bytes on x86_64 archs.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Implement zio_execute() as a wrapper around the static function
__zio_execute() so that we can force __zio_execute() to be inlined.
This reduces stack overhead which is important because __zio_execute()
is called recursively in several zio code paths. zio_execute() itself
cannot be inlined because it is externally visible.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Eliminated local variables pointing to members of the zio struct.
Just refer to the struct members directly. This saved about 32 bytes per
call, but this function can be called recurisvely up to 19 levels deep,
so we potentially save up to 608 bytes.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Certain function must never be automatically inlined by gcc because
they are stack heavy or called recursively. This patch flags all
such functions I've found as 'noinline' to prevent gcc from making
the optimization.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reduce kernel stack usage by lzjb_compress() by moving uint16 array
off the stack and on to the heap. The exact performance implications
of this I have not measured but we absolutely need to keep stack
usage to a minimum. If/when this becomes and issue we optimize.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Decrease stack usage for various call paths by forcing certain
functions to be inlined. By inlining the functions the overhead
of a new stack frame is removed at the cost of increased code size.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
To reduce stack overhead this topic branch moves the 128 byte
blkptr_t data strucutre in dsl_scan_visitbp() to the heap.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reduce stack usage in dsl_deleg_get, gcc flagged it as consuming a
whopping 1040 bytes or potentially 1/4 of a 4K stack. This patch
moves all the large structures and buffer off the stack and on to
the heap. This includes 2 zap_cursor_t structs each 52 bytes in
size, 2 zap_attribute_t structs each 280 bytes in size, and 1
256 byte char array. The total saves on the stack is 880 bytes
after you account for the 5 new pointers added.
Also the source buffer length has been increased from MAXNAMELEN
to MAXNAMELEN+strlen(MOS_DIR_NAME)+1 as described by the comment in
dsl_dir_name(). A buffer overrun may have been possible with the
slightly smaller buffer.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Move dsl_dataset_t local variable from the stack to the heap.
This reduces the stack usage of this function from 2048 bytes
to 176 bytes for x84_64 arches.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reduce stack usage by 276 bytes by moving the snaparg struct from the
stack to the heap. We have limited stack space we must not waste.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
This commit preserves the recursive function dbuf_hold_impl() but moves
the local variables and function arguments to the heap to minimize
the stack frame size. Enough space is initially allocated on the
stack for 20 levels of recursion. This technique was based on commit
34229a2f2ac07363f64ddd63e014964fff2f0671 which reduced stack usage of
traverse_visitbp().
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
The dnode_move() functionality is only used in the kernel build.
As such we should be careful to wrap all of the related code
with '#ifdef _KERNEL' to avoid gcc warnings about unused code.
Interestingly this looks like an upstream bug as well. If for some
reason we are unable to get a zvols statistics, because perhaps the
zpool is hopelessly corrupt, we would trigger the VERIFY. This
commit adds the proper error handling just to propagate the error
back to user space. Now the user space tools still must handle this
properly but in the worst case the tool will crash or perhaps have
some missing output. That's far far better than crashing the host.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
The zio_taskq_dispatch() function may be called at interrupt time
and it is critical that we never sleep.
Additionally, wrap taskq_dispatch() in a while loop because it may
fail. This is non optimal but is OK for now.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Do not use zmod.h in userspace.
This has also been filed with the ZFS team. It makes the userspace
libzpool code use the zlib API, instead of the Solaris-only and
non-standard zmod.h. The zlib API is almost identical and is a de
facto standard, so this is a no-brainer.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
If your only going to allow one allocator to be used and it is defined
at compile time there is no point including the others in the build.
This patch could/should be refined for Linux to make the metaslab
configurable at run time. That might be a bit tricky however since
you would need to quiese all IO. Short of that making it configurable
as a module load option would be a reasonable compromise.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Remove all instances of list handling where the API is not used
and instead list data members are directly accessed. Doing this
sort of thing is bad for portability.
Additionally, ensure that list_link_init() is called on newly
created list nodes. This ensures the node is properly initialized
and does not rely on the assumption that zero'ing the list_node_t
via kmem_zalloc() is the same as proper initialization.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Move xiou stat structures from a header to the dmu.c source as is
done with all the other kstat interfaces. This information is local
to dmu.c registered the xuio kstat and should stay that way.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Replace non-fatal assertion with warning. This was being observed
during testing and it should not be fatal.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
In the linux kernel 'current' is defined to mean the current process
and can never be used as a local variable in a function. Simply
replace all usage of 'current' with 'curr' in this function.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
The upstream commit cb code had a few bugs:
1) The arguments of the list_move_tail() call in txg_dispatch_callbacks()
were reversed by mistake. This caused the commit callbacks to not be
called at all.
2) ztest had a bug in ztest_dmu_commit_callbacks() where "error" was not
initialized correctly. This seems to have caused the test to always take
the simulated error code path, which made ztest unable to detect whether
commit cbs were being called for transactions that successfuly complete.
3) ztest had another bug in ztest_dmu_commit_callbacks() where the commit
cb threshold was not being compared correctly.
4) The commit cb taskq was using 'max_ncpus * 2' as the maxalloc argument
of taskq_create(), which could have caused unnecessary delays in the txg
sync thread.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Fix non-c90 compliant code, for the most part these changes
simply deal with where a particular variable is declared.
Under c90 it must alway be done at the very start of a block.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
