The current codebase does not support raw sending buffers with block
size > 128kB when large_blocks is not active. This can happen in the
codepath dsl_dataset_sync()->dmu_objset_sync()->zio_nowait() which
calls back dmu_objset_write_done()->dsl_dataset_block_born(). If
dsl_dataset_sync() completes its run before dsl_dataset_block_born() is
called, we will end up not activating some of the necessary flags, while
having blocks based on those flags written in the filesystem. A
subsequent send will then panic.
Fix this by directly deciding in dmu_objset_sync() whether these flags
need to be activated later by dsl_dataset_sync(). Instead of panicking
due to a NULL pointer dereference in dmu_dump_write() in case of a send,
print out an error message. Also during scrub verify there are no
contradicting filesystem flags.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#12275Closes#12438
bcopy() has a confusing argument order and is actually a move, not a
copy; they're all deprecated since POSIX.1-2001 and removed in -2008,
and we shim them out to mem*() on Linux anyway
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12996
Evaluated every variable that lives in .data (and globals in .rodata)
in the kernel modules, and constified/eliminated/localised them
appropriately. This means that all read-only data is now actually
read-only data, and, if possible, at file scope. A lot of previously-
global-symbols became inlinable (and inlined!) constants. Probably
not in a big Wowee Performance Moment, but hey.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12899
Special allocation class or dedup vdevs may have roughly the same
performance as L2ARC vdevs. Introduce a new tunable to exclude those
buffers from being cacheable on L2ARC.
Reviewed-by: Don Brady <don.brady@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#11761Closes#12285
The number of sublists in a multilist is relatively small. We dont need
64 bits to calculate an index. 32 bits is sufficient and makes the
code more efficient.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12288
ZFS loves using %llu for uint64_t, but that requires a cast to not
be noisy - which is even done in many, though not all, places.
Also a couple places used %u for uint64_t, which were promoted
to %llu.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12233
This commit partially reverts changes to multilists in PR 7968
(multi-threaded spa-sync()) and adds some cache line alignments to
separate read-only multilists and heavily modified refcount's to different
cache lines.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-by: iXsystems, Inc.
Closes#12158
Follow up for commit 624222a, value asserted <= SPA_OLD_MAXBLOCKSIZE
instead of SPA_MAXBLOCKSIZE as it should be after the previous change.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#11501
Build error on illumos with gcc 10 did reveal:
In function 'dmu_objset_refresh_ownership':
../../common/fs/zfs/dmu_objset.c:857:25: error: implicit conversion
from 'boolean_t' to 'ds_hold_flags_t' {aka 'enum ds_hold_flags'}
[-Werror=enum-conversion]
857 | dsl_dataset_disown(ds, decrypt, tag);
| ^~~~~~~
cc1: all warnings being treated as errors
libzfs_input_check.c: In function 'zfs_ioc_input_tests':
libzfs_input_check.c:754:28: error: implicit conversion from
'enum dmu_objset_type' to 'enum lzc_dataset_type'
[-Werror=enum-conversion]
754 | err = lzc_create(dataset, DMU_OST_ZFS, NULL, NULL, 0);
| ^~~~~~~~~~~
cc1: all warnings being treated as errors
The same issue is present in openzfs, and also the same issue about
ds_hold_flags_t, which currently defines exactly one valid value.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Toomas Soome <tsoome@me.com>
Closes#11406
After porting the fix for https://github.com/openzfs/zfs/issues/5295
over to illumos, we started hitting an assertion failure when running
the testsuite:
assertion failed: rc->rc_count == number, file: .../refcount.c
and the unexpected hold has this stack:
dsl_dataset_long_hold+0x59 dmu_objset_upgrade+0x73
dmu_objset_id_quota_upgrade+0x15 dmu_objset_own+0x14f
The simplest reproducer for this in illumos is
zpool create -f -O version=1 testpool c3t0d0; zpool destroy testpool
which is run as part of the zpool_create_tempname test, but I can't get
this to trigger on FreeBSD. This appears to be because of the call to
txg_wait_synced() in dmu_objset_upgrade_stop() (which was missing in
illumos), slows down dmu_objset_disown() enough to avoid the condition.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andy Fiddaman <andy@omnios.org>
Closes#11368
The performance of `zfs receive` can be bottlenecked on the CPU consumed
by the `receive_writer` thread, especially when receiving streams with
small compressed block sizes. Much of the CPU is spent creating and
destroying dbuf's and arc buf's, one for each `WRITE` record in the send
stream.
This commit introduces the concept of "lightweight writes", which allows
`zfs receive` to write to the DMU by providing an ABD, and instantiating
only a new type of `dbuf_dirty_record_t`. The dbuf and arc buf for this
"dirty leaf block" are not instantiated.
Because there is no dbuf with the dirty data, this mechanism doesn't
support reading from "lightweight-dirty" blocks (they would see the
on-disk state rather than the dirty data). Since the dedup-receive code
has been removed, `zfs receive` is write-only, so this works fine.
Because there are no arc bufs for the received data, the received data
is no longer cached in the ARC.
Testing a receive of a stream with average compressed block size of 4KB,
this commit improves performance by 50%, while also reducing CPU usage
by 50% of a CPU. On a per-block basis, CPU consumed by receive_writer()
and dbuf_evict() is now 1/7th (14%) of what it was.
Baseline: 450MB/s, CPU in receive_writer() 40% + dbuf_evict() 35%
New: 670MB/s, CPU in receive_writer() 17% + dbuf_evict() 0%
The code is also restructured in a few ways:
Added a `dr_dnode` field to the dbuf_dirty_record_t. This simplifies
some existing code that no longer needs `DB_DNODE_ENTER()` and related
routines. The new field is needed by the lightweight-type dirty record.
To ensure that the `dr_dnode` field remains valid until the dirty record
is freed, we have to ensure that the `dnode_move()` doesn't relocate the
dnode_t. To do this we keep a hold on the dnode until it's zio's have
completed. This is already done by the user-accounting code
(`userquota_updates_task()`), this commit extends that so that it always
keeps the dnode hold until zio completion (see `dnode_rele_task()`).
`dn_dirty_txg` was previously zeroed when the dnode was synced. This
was not necessary, since its meaning can be "when was this dnode last
dirtied". This change simplifies the new `dnode_rele_task()` code.
Removed some dead code related to `DRR_WRITE_BYREF` (dedup receive).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: George Wilson <gwilson@delphix.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#11105
For encrypted receives, where user accounting is initially disabled on
creation, both 'zfs userspace' and 'zfs groupspace' fails with
EOPNOTSUPP: this is because dmu_objset_id_quota_upgrade_cb() forgets to
set OBJSET_FLAG_USERACCOUNTING_COMPLETE on the objset flags after a
successful dmu_objset_space_upgrade().
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#9501Closes#9596
In C, const indicates to the reader that mutation will not occur.
It can also serve as a hint about ownership.
Add const in a few places where it makes sense.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#10997
This PR adds two new compression types, based on ZStandard:
- zstd: A basic ZStandard compression algorithm Available compression.
Levels for zstd are zstd-1 through zstd-19, where the compression
increases with every level, but speed decreases.
- zstd-fast: A faster version of the ZStandard compression algorithm
zstd-fast is basically a "negative" level of zstd. The compression
decreases with every level, but speed increases.
Available compression levels for zstd-fast:
- zstd-fast-1 through zstd-fast-10
- zstd-fast-20 through zstd-fast-100 (in increments of 10)
- zstd-fast-500 and zstd-fast-1000
For more information check the man page.
Implementation details:
Rather than treat each level of zstd as a different algorithm (as was
done historically with gzip), the block pointer `enum zio_compress`
value is simply zstd for all levels, including zstd-fast, since they all
use the same decompression function.
The compress= property (a 64bit unsigned integer) uses the lower 7 bits
to store the compression algorithm (matching the number of bits used in
a block pointer, as the 8th bit was borrowed for embedded block
pointers). The upper bits are used to store the compression level.
It is necessary to be able to determine what compression level was used
when later reading a block back, so the concept used in LZ4, where the
first 32bits of the on-disk value are the size of the compressed data
(since the allocation is rounded up to the nearest ashift), was
extended, and we store the version of ZSTD and the level as well as the
compressed size. This value is returned when decompressing a block, so
that if the block needs to be recompressed (L2ARC, nop-write, etc), that
the same parameters will be used to result in the matching checksum.
All of the internal ZFS code ( `arc_buf_hdr_t`, `objset_t`,
`zio_prop_t`, etc.) uses the separated _compress and _complevel
variables. Only the properties ZAP contains the combined/bit-shifted
value. The combined value is split when the compression_changed_cb()
callback is called, and sets both objset members (os_compress and
os_complevel).
The userspace tools all use the combined/bit-shifted value.
Additional notes:
zdb can now also decode the ZSTD compression header (flag -Z) and
inspect the size, version and compression level saved in that header.
For each record, if it is ZSTD compressed, the parameters of the decoded
compression header get printed.
ZSTD is included with all current tests and new tests are added
as-needed.
Per-dataset feature flags now get activated when the property is set.
If a compression algorithm requires a feature flag, zfs activates the
feature when the property is set, rather than waiting for the first
block to be born. This is currently only used by zstd but can be
extended as needed.
Portions-Sponsored-By: The FreeBSD Foundation
Co-authored-by: Allan Jude <allanjude@freebsd.org>
Co-authored-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Co-authored-by: Kjeld Schouten-Lebbing <kjeld@schouten-lebbing.nl>
Co-authored-by: Michael Niewöhner <foss@mniewoehner.de>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Allan Jude <allanjude@freebsd.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Kjeld Schouten-Lebbing <kjeld@schouten-lebbing.nl>
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Closes#6247Closes#9024Closes#10277Closes#10278
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Closes#10636
The filesystem_limit and snapshot_limit properties limit the number of
filesystems or snapshots that can be created below this dataset.
According to the manpage, "The limit is not enforced if the user is
allowed to change the limit." Two types of users are allowed to change
the limit:
1. Those that have been delegated the `filesystem_limit` or
`snapshot_limit` permission, e.g. with
`zfs allow USER filesystem_limit DATASET`. This works properly.
2. A user with elevated system privileges (e.g. root). This does not
work - the root user will incorrectly get an error when trying to create
a snapshot/filesystem, if it exceeds the `_limit` property.
The problem is that `priv_policy_ns()` does not work if the `cred_t` is
not that of the current process. This happens when
`dsl_enforce_ds_ss_limits()` is called in syncing context (as part of a
sync task's check func) to determine the permissions of the
corresponding user process.
This commit fixes the issue by passing the `task_struct` (typedef'ed as
a `proc_t`) to syncing context, and then using `has_capability()` to
determine if that process is privileged. Note that we still need to
pass the `cred_t` to syncing context so that we can check if the user
was delegated this permission with `zfs allow`.
This problem only impacts Linux. Wrappers are added to FreeBSD but it
continues to use `priv_check_cred()`, which works on arbitrary `cred_t`.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#8226Closes#10545
Mark functions used only in the same translation unit as static. This
only includes functions that do not have a prototype in a header file
either.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Closes#10470
Background:
By increasing the recordsize property above the default of 128KB, a
filesystem may have "large" blocks. By default, a send stream of such a
filesystem does not contain large WRITE records, instead it decreases
objects' block sizes to 128KB and splits the large blocks into 128KB
blocks, allowing the large-block filesystem to be received by a system
that does not support the `large_blocks` feature. A send stream
generated by `zfs send -L` (or `--large-block`) preserves the large
block size on the receiving system, by using large WRITE records.
When receiving an incremental send stream for a filesystem with large
blocks, if the send stream's -L flag was toggled, a bug is encountered
in which the file's contents are incorrectly zeroed out. The contents
of any blocks that were not modified by this send stream will be lost.
"Toggled" means that the previous send used `-L`, but this incremental
does not use `-L` (-L to no-L); or that the previous send did not use
`-L`, but this incremental does use `-L` (no-L to -L).
Changes:
This commit addresses the problem with several changes to the semantics
of zfs send/receive:
1. "-L to no-L" incrementals are rejected. If the previous send used
`-L`, but this incremental does not use `-L`, the `zfs receive` will
fail with this error message:
incremental send stream requires -L (--large-block), to match
previous receive.
2. "no-L to -L" incrementals are handled correctly, preserving the
smaller (128KB) block size of any already-received files that used large
blocks on the sending system but were split by `zfs send` without the
`-L` flag.
3. A new send stream format flag is added, `SWITCH_TO_LARGE_BLOCKS`.
This feature indicates that we can correctly handle "no-L to -L"
incrementals. This flag is currently not set on any send streams. In
the future, we intend for incremental send streams of snapshots that
have large blocks to use `-L` by default, and these streams will also
have the `SWITCH_TO_LARGE_BLOCKS` feature set. This ensures that streams
from the default use of `zfs send` won't encounter the bug mentioned
above, because they can't be received by software with the bug.
Implementation notes:
To facilitate accessing the ZPL's generation number,
`zfs_space_delta_cb()` has been renamed to `zpl_get_file_info()` and
restructured to fill in a struct with ZPL-specific info including owner
and generation.
In the "no-L to -L" case, if this is a compressed send stream (from
`zfs send -cL`), large WRITE records that are being written to small
(128KB) blocksize files need to be decompressed so that they can be
written split up into multiple blocks. The zio pipeline will recompress
each smaller block individually.
A new test case, `send-L_toggle`, is added, which tests the "no-L to -L"
case and verifies that we get an error for the "-L to no-L" case.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#6224Closes#10383
The strcpy() and sprintf() functions are deprecated on some platforms.
Care is needed to ensure correct size is used. If some platforms
miss snprintf, we can add a #define to sprintf, likewise strlcpy().
The biggest change is adding a size parameter to zfs_id_to_fuidstr().
The various *_impl_get() functions are only used on linux and have
not yet been updated.
Reviewed by: Sean Eric Fagan <sef@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Closes#10400
The normal lock order is that the dp_config_rwlock must be held before
the ds_opening_lock. For example, dmu_objset_hold() does this.
However, dmu_objset_open_impl() is called with the ds_opening_lock held,
and if the dp_config_rwlock is not already held, it will attempt to
acquire it. This may lead to deadlock, since the lock order is
reversed.
Looking at all the callers of dmu_objset_open_impl() (which is
principally the callers of dmu_objset_from_ds()), almost all callers
already have the dp_config_rwlock. However, there are a few places in
the send and receive code paths that do not. For example:
dsl_crypto_populate_key_nvlist, send_cb, dmu_recv_stream,
receive_write_byref, redact_traverse_thread.
This commit resolves the problem by requiring all callers ot
dmu_objset_from_ds() to hold the dp_config_rwlock. In most cases, the
code has been restructured such that we call dmu_objset_from_ds()
earlier on in the send and receive processes, when we already have the
dp_config_rwlock, and save the objset_t until we need it in the middle
of the send or receive (similar to what we already do with the
dsl_dataset_t). Thus we do not need to acquire the dp_config_rwlock in
many new places.
I also cleaned up code in dmu_redact_snap() and send_traverse_thread().
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Paul Zuchowski <pzuchowski@datto.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#9662Closes#10115
When "zfs destroy" is run, it completes quickly, and in the background
we locate the blocks to free and free them. This background activity
can be observed with `zpool get freeing` and `zpool wait -t free ...`.
This background activity is processed by a single thread (the spa_sync
thread) which calls zio_free() on each of the blocks to free. With even
modest storage performance, the CPU consumption of zio_free() can be the
performance bottleneck.
Performance of zio_free() can be improved by not actually creating a
zio_t in the common case (non-dedup, non-gang), instead calling
metaslab_free() directly. This avoids the CPU cost of allocating the
zio_t, and more importantly the cost of adding and later removing this
zio_t from the parent zio's child list.
The result is that performance of background freeing more than doubles,
from 0.6 million blocks per second to 1.3 million blocks per second.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Wilson <gwilson@delphix.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#10034
Additionally pull in state machine comments about
upcoming async cow work.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Ahrens <matt@delphix.com>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9902
When we finish a zfs receive, dmu_recv_end_sync() calls
zvol_create_minors(async=TRUE). This kicks off some other threads that
create the minor device nodes (in /dev/zvol/poolname/...). These async
threads call zvol_prefetch_minors_impl() and zvol_create_minor(), which
both call dmu_objset_own(), which puts a "long hold" on the dataset.
Since the zvol minor node creation is asynchronous, this can happen
after the `ZFS_IOC_RECV[_NEW]` ioctl and `zfs receive` process have
completed.
After the first receive ioctl has completed, userland may attempt to do
another receive into the same dataset (e.g. the next incremental
stream). This second receive and the asynchronous minor node creation
can interfere with one another in several different ways, because they
both require exclusive access to the dataset:
1. When the second receive is finishing up, dmu_recv_end_check() does
dsl_dataset_handoff_check(), which can fail with EBUSY if the async
minor node creation already has a "long hold" on this dataset. This
causes the 2nd receive to fail.
2. The async udev rule can fail if zvol_id and/or systemd-udevd try to
open the device while the the second receive's async attempt at minor
node creation owns the dataset (via zvol_prefetch_minors_impl). This
causes the minor node (/dev/zd*) to exist, but the udev-generated
/dev/zvol/... to not exist.
3. The async minor node creation can silently fail with EBUSY if the
first receive's zvol_create_minor() trys to own the dataset while the
second receive's zvol_prefetch_minors_impl already owns the dataset.
To address these problems, this change synchronously creates the minor
node. To avoid the lock ordering problems that the asynchrony was
introduced to fix (see #3681), we create the minor nodes from open
context, with no locks held, rather than from syncing contex as was
originally done.
Implementation notes:
We generally do not need to traverse children or prefetch anything (e.g.
when running the recv, snapshot, create, or clone subcommands of zfs).
We only need recursion when importing/opening a pool and when loading
encryption keys. The existing recursive, asynchronous, prefetching code
is preserved for use in these cases.
Channel programs may need to create zvol minor nodes, when creating a
snapshot of a zvol with the snapdev property set. We figure out what
snapshots are created when running the LUA program in syncing context.
In this case we need to remember what snapshots were created, and then
try to create their minor nodes from open context, after the LUA code
has completed.
There are additional zvol use cases that asynchronously own the dataset,
which can cause similar problems. E.g. changing the volmode or snapdev
properties. These are less problematic because they are not recursive
and don't touch datasets that are not involved in the operation, there
is still potential for interference with subsequent operations. In the
future, these cases should be similarly converted to create the zvol
minor node synchronously from open context.
The async tasks of removing and renaming minors do not own the objset,
so they do not have this problem. However, it may make sense to also
convert these operations to happen synchronously from open context, in
the future.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Prakash Surya <prakash.surya@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
External-issue: DLPX-65948
Closes#7863Closes#9885
In the FreeBSD kernel the strdup signature is:
```
char *strdup(const char *__restrict, struct malloc_type *);
```
It's unfortunate that the developers have chosen to change
the signature of libc functions - but it's what I have to
deal with.
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9433
This patch implements a new tree structure for ZFS, and uses it to
store range trees more efficiently.
The new structure is approximately a B-tree, though there are some
small differences from the usual characterizations. The tree has core
nodes and leaf nodes; each contain data elements, which the elements
in the core nodes acting as separators between its children. The
difference between core and leaf nodes is that the core nodes have an
array of children, while leaf nodes don't. Every node in the tree may
be only partially full; in most cases, they are all at least 50% full
(in terms of element count) except for the root node, which can be
less full. Underfull nodes will steal from their neighbors or merge to
remain full enough, while overfull nodes will split in two. The data
elements are contained in tree-controlled buffers; they are copied
into these on insertion, and overwritten on deletion. This means that
the elements are not independently allocated, which reduces overhead,
but also means they can't be shared between trees (and also that
pointers to them are only valid until a side-effectful tree operation
occurs). The overhead varies based on how dense the tree is, but is
usually on the order of about 50% of the element size; the per-node
overheads are very small, and so don't make a significant difference.
The trees can accept arbitrary records; they accept a size and a
comparator to allow them to be used for a variety of purposes.
The new trees replace the AVL trees used in the range trees today.
Currently, the range_seg_t structure contains three 8 byte integers
of payload and two 24 byte avl_tree_node_ts to handle its storage in
both an offset-sorted tree and a size-sorted tree (total size: 64
bytes). In the new model, the range seg structures are usually two 4
byte integers, but a separate one needs to exist for the size-sorted
and offset-sorted tree. Between the raw size, the 50% overhead, and
the double storage, the new btrees are expected to use 8*1.5*2 = 24
bytes per record, or 33.3% as much memory as the AVL trees (this is
for the purposes of storing metaslab range trees; for other purposes,
like scrubs, they use ~50% as much memory).
We reduced the size of the payload in the range segments by teaching
range trees about starting offsets and shifts; since metaslabs have a
fixed starting offset, and they all operate in terms of disk sectors,
we can store the ranges using 4-byte integers as long as the size of
the metaslab divided by the sector size is less than 2^32. For 512-byte
sectors, this is a 2^41 (or 2TB) metaslab, which with the default
settings corresponds to a 256PB disk. 4k sector disks can handle
metaslabs up to 2^46 bytes, or 2^63 byte disks. Since we do not
anticipate disks of this size in the near future, there should be
almost no cases where metaslabs need 64-byte integers to store their
ranges. We do still have the capability to store 64-byte integer ranges
to account for cases where we are storing per-vdev (or per-dnode) trees,
which could reasonably go above the limits discussed. We also do not
store fill information in the compact version of the node, since it
is only used for sorted scrub.
We also optimized the metaslab loading process in various other ways
to offset some inefficiencies in the btree model. While individual
operations (find, insert, remove_from) are faster for the btree than
they are for the avl tree, remove usually requires a find operation,
while in the AVL tree model the element itself suffices. Some clever
changes actually caused an overall speedup in metaslab loading; we use
approximately 40% less cpu to load metaslabs in our tests on Illumos.
Another memory and performance optimization was achieved by changing
what is stored in the size-sorted trees. When a disk is heavily
fragmented, the df algorithm used by default in ZFS will almost always
find a number of small regions in its initial cursor-based search; it
will usually only fall back to the size-sorted tree to find larger
regions. If we increase the size of the cursor-based search slightly,
and don't store segments that are smaller than a tunable size floor
in the size-sorted tree, we can further cut memory usage down to
below 20% of what the AVL trees store. This also results in further
reductions in CPU time spent loading metaslabs.
The 16KiB size floor was chosen because it results in substantial memory
usage reduction while not usually resulting in situations where we can't
find an appropriate chunk with the cursor and are forced to use an
oversized chunk from the size-sorted tree. In addition, even if we do
have to use an oversized chunk from the size-sorted tree, the chunk
would be too small to use for ZIL allocations, so it isn't as big of a
loss as it might otherwise be. And often, more small allocations will
follow the initial one, and the cursor search will now find the
remainder of the chunk we didn't use all of and use it for subsequent
allocations. Practical testing has shown little or no change in
fragmentation as a result of this change.
If the size-sorted tree becomes empty while the offset sorted one still
has entries, it will load all the entries from the offset sorted tree
and disregard the size floor until it is unloaded again. This operation
occurs rarely with the default setting, only on incredibly thoroughly
fragmented pools.
There are some other small changes to zdb to teach it to handle btrees,
but nothing major.
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed by: Sebastien Roy seb@delphix.com
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#9181
Refactor the zvol in to platform dependent and independent bits.
Reviewed-by: Allan Jude <allanjude@freebsd.org>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9295
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Closes#9240
Even though the bug's writeup (Github issue #9136) is very detailed,
we still don't know exactly how we got to that state, thus I wasn't
able to reproduce the bug. That said, we can make an educated guess
combining the information on filled issue with the code.
From the fact that `dp_dirty_total` was 0 (which is less than
`zfs_dirty_data_max`) we know that there was one thread that set it to
0 and then signaled one of the waiters of `dp_spaceavail_cv` [see
`dsl_pool_dirty_delta()` which is also the only place that
`dp_dirty_total` is changed]. Thus, the only logical explaination
then for the bug being hit is that the waiter that just got awaken
didn't go through `dsl_pool_dirty_data()`. Given that this function
is only called by `dsl_pool_dirty_space()` or `dsl_pool_undirty_space()`
I can only think of two possible ways of the above scenario happening:
[1] The waiter didn't call into any of the two functions - which I
find highly unlikely (i.e. why wait on `dp_spaceavail_cv` to begin
with?).
[2] The waiter did call in one of the above function but it passed 0 as
the space/delta to be dirtied (or undirtied) and then the callee
returned immediately (e.g both `dsl_pool_dirty_space()` and
`dsl_pool_undirty_space()` return immediately when space is 0).
In any case and no matter how we got there, the easy fix would be to
just broadcast to all waiters whenever `dp_dirty_total` hits 0. That
said and given that we've never hit this before, it would make sense
to think more on why the above situation occured.
Attempting to mimic what Prakash was doing in the issue filed, I
created a dataset with `sync=always` and started doing contiguous
writes in a file within that dataset. I observed with DTrace that even
though we update the pool's dirty data accounting when we would dirty
stuff, the accounting wouldn't be decremented incrementally as we were
done with the ZIOs of those writes (the reason being that
`dbuf_write_physdone()` isn't be called as we go through the override
code paths, and thus `dsl_pool_undirty_space()` is never called). As a
result we'd have to wait until we get to `dsl_pool_sync()` where we
zero out all dirty data accounting for the pool and the current TXG's
metadata.
In addition, as Matt noted and I later verified, the same issue would
arise when using dedup.
In both cases (sync & dedup) we shouldn't have to wait until
`dsl_pool_sync()` zeros out the accounting data. According to the
comment in that part of the code, the reasons why we do the zeroing,
have nothing to do with what we observe:
````
/*
* We have written all of the accounted dirty data, so our
* dp_space_towrite should now be zero. However, some seldom-used
* code paths do not adhere to this (e.g. dbuf_undirty(), also
* rounding error in dbuf_write_physdone).
* Shore up the accounting of any dirtied space now.
*/
dsl_pool_undirty_space(dp, dp->dp_dirty_pertxg[txg & TXG_MASK], txg);
````
Ideally what we want to do is to undirty in the accounting exactly what
we dirty (I use the word ideally as we can still have rounding errors).
This would make the behavior of the system more clear and predictable.
Another interesting issue that I observed with DTrace was that we
wouldn't update any of the pool's dirty data accounting whenever we
would dirty and/or undirty MOS data. In addition, every time we would
change the size of a dbuf through `dbuf_new_size()` we wouldn't update
the accounted space dirtied in the appropriate dirty record, so when
ZIOs are done we would undirty less that we dirtied from the pool's
accounting point of view.
For the first two issues observed (sync & dedup) this patch ensures
that we still update the pool's accounting when we undirty data,
regardless of the write being physical or not.
For changes in the MOS, we first ensure to zero out the pool's dirty
data accounting in `dsl_pool_sync()` after we synced the MOS. Then we
can go ahead and enable the update of the pool's dirty data accounting
wheneve we change MOS data.
Another fix is that we now update the accounting explicitly for
counting errors in `dbuf_write_done()`.
Finally, `dbuf_new_size()` updates the accounted space of the
appropriate dirty record correctly now.
The problem is that we still don't know how the bug came up in the
issue filled. That said the issues fixed seem to be very relevant, so
instead of going with the broadcasting solution right away,
I decided to leave this patch as is.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Prakash Surya <prakash.surya@delphix.com>
Signed-off-by: Serapheim Dimitropoulos <serapheim@delphix.com>
External-issue: DLPX-47285
Closes#9137
= Motivation
At Delphix we've seen a lot of customer systems where fragmentation
is over 75% and random writes take a performance hit because a lot
of time is spend on I/Os that update on-disk space accounting metadata.
Specifically, we seen cases where 20% to 40% of sync time is spend
after sync pass 1 and ~30% of the I/Os on the system is spent updating
spacemaps.
The problem is that these pools have existed long enough that we've
touched almost every metaslab at least once, and random writes
scatter frees across all metaslabs every TXG, thus appending to
their spacemaps and resulting in many I/Os. To give an example,
assuming that every VDEV has 200 metaslabs and our writes fit within
a single spacemap block (generally 4K) we have 200 I/Os. Then if we
assume 2 levels of indirection, we need 400 additional I/Os and
since we are talking about metadata for which we keep 2 extra copies
for redundancy we need to triple that number, leading to a total of
1800 I/Os per VDEV every TXG.
We could try and decrease the number of metaslabs so we have less
I/Os per TXG but then each metaslab would cover a wider range on
disk and thus would take more time to be loaded in memory from disk.
In addition, after it's loaded, it's range tree would consume more
memory.
Another idea would be to just increase the spacemap block size
which would allow us to fit more entries within an I/O block
resulting in fewer I/Os per metaslab and a speedup in loading time.
The problem is still that we don't deal with the number of I/Os
going up as the number of metaslabs is increasing and the fact
is that we generally write a lot to a few metaslabs and a little
to the rest of them. Thus, just increasing the block size would
actually waste bandwidth because we won't be utilizing our bigger
block size.
= About this patch
This patch introduces the Log Spacemap project which provides the
solution to the above problem while taking into account all the
aforementioned tradeoffs. The details on how it achieves that can
be found in the references sections below and in the code (see
Big Theory Statement in spa_log_spacemap.c).
Even though the change is fairly constraint within the metaslab
and lower-level SPA codepaths, there is a side-change that is
user-facing. The change is that VDEV IDs from VDEV holes will no
longer be reused. To give some background and reasoning for this,
when a log device is removed and its VDEV structure was replaced
with a hole (or was compacted; if at the end of the vdev array),
its vdev_id could be reused by devices added after that. Now
with the pool-wide space maps recording the vdev ID, this behavior
can cause problems (e.g. is this entry referring to a segment in
the new vdev or the removed log?). Thus, to simplify things the
ID reuse behavior is gone and now vdev IDs for top-level vdevs
are truly unique within a pool.
= Testing
The illumos implementation of this feature has been used internally
for a year and has been in production for ~6 months. For this patch
specifically there don't seem to be any regressions introduced to
ZTS and I have been running zloop for a week without any related
problems.
= Performance Analysis (Linux Specific)
All performance results and analysis for illumos can be found in
the links of the references. Redoing the same experiments in Linux
gave similar results. Below are the specifics of the Linux run.
After the pool reached stable state the percentage of the time
spent in pass 1 per TXG was 64% on average for the stock bits
while the log spacemap bits stayed at 95% during the experiment
(graph: sdimitro.github.io/img/linux-lsm/PercOfSyncInPassOne.png).
Sync times per TXG were 37.6 seconds on average for the stock
bits and 22.7 seconds for the log spacemap bits (related graph:
sdimitro.github.io/img/linux-lsm/SyncTimePerTXG.png). As a result
the log spacemap bits were able to push more TXGs, which is also
the reason why all graphs quantified per TXG have more entries for
the log spacemap bits.
Another interesting aspect in terms of txg syncs is that the stock
bits had 22% of their TXGs reach sync pass 7, 55% reach sync pass 8,
and 20% reach 9. The log space map bits reached sync pass 4 in 79%
of their TXGs, sync pass 7 in 19%, and sync pass 8 at 1%. This
emphasizes the fact that not only we spend less time on metadata
but we also iterate less times to convergence in spa_sync() dirtying
objects.
[related graphs:
stock- sdimitro.github.io/img/linux-lsm/NumberOfPassesPerTXGStock.png
lsm- sdimitro.github.io/img/linux-lsm/NumberOfPassesPerTXGLSM.png]
Finally, the improvement in IOPs that the userland gains from the
change is approximately 40%. There is a consistent win in IOPS as
you can see from the graphs below but the absolute amount of
improvement that the log spacemap gives varies within each minute
interval.
sdimitro.github.io/img/linux-lsm/StockVsLog3Days.png
sdimitro.github.io/img/linux-lsm/StockVsLog10Hours.png
= Porting to Other Platforms
For people that want to port this commit to other platforms below
is a list of ZoL commits that this patch depends on:
Make zdb results for checkpoint tests consistent
db587941c5
Update vdev_is_spacemap_addressable() for new spacemap encoding
419ba59145
Simplify spa_sync by breaking it up to smaller functions
8dc2197b7b
Factor metaslab_load_wait() in metaslab_load()
b194fab0fb
Rename range_tree_verify to range_tree_verify_not_present
df72b8bebe
Change target size of metaslabs from 256GB to 16GB
c853f382db
zdb -L should skip leak detection altogether
21e7cf5da8
vs_alloc can underflow in L2ARC vdevs
7558997d2f
Simplify log vdev removal code
6c926f426a
Get rid of space_map_update() for ms_synced_length
425d3237ee
Introduce auxiliary metaslab histograms
928e8ad47d
Error path in metaslab_load_impl() forgets to drop ms_sync_lock
8eef997679
= References
Background, Motivation, and Internals of the Feature
- OpenZFS 2017 Presentation:
youtu.be/jj2IxRkl5bQ
- Slides:
slideshare.net/SerapheimNikolaosDim/zfs-log-spacemaps-project
Flushing Algorithm Internals & Performance Results
(Illumos Specific)
- Blogpost:
sdimitro.github.io/post/zfs-lsm-flushing/
- OpenZFS 2018 Presentation:
youtu.be/x6D2dHRjkxw
- Slides:
slideshare.net/SerapheimNikolaosDim/zfs-log-spacemap-flushing-algorithm
Upstream Delphix Issues:
DLPX-51539, DLPX-59659, DLPX-57783, DLPX-61438, DLPX-41227, DLPX-59320
DLPX-63385
Reviewed-by: Sean Eric Fagan <sef@ixsystems.com>
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Closes#8442
DMU sync code calls taskq_dispatch() for each sublist of os_dirty_dnodes
and os_synced_dnodes. Since the number of sublists by default is equal
to number of CPUs, it will dispatch equal, potentially large, number of
tasks, waking up many CPUs to handle them, even if only one or few of
sublists actually have any work to do.
This change adds check for empty sublists to avoid this.
Reviewed by: Sean Eric Fagan <sef@ixsystems.com>
Reviewed by: Matt Ahrens <matt@delphix.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#8909
The "zfs remap" command was disabled by
6e91a72fe3, because it has little utility
and introduced some tricky bugs. This commit removes the code for it,
the associated ZFS_IOC_REMAP ioctl, and tests.
Note that the ioctl and property will remain, but have no functionality.
This allows older software to fail gracefully if it attempts to use
these, and avoids a backwards incompatibility that would be introduced if
we renumbered the later ioctls/props.
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#8944
When encryption was first added to ZFS, we made a decision to
prevent users from creating unencrypted children of encrypted
datasets. The idea was to prevent users from inadvertently
leaving some of their data unencrypted. However, since the
release of 0.8.0, some legitimate reasons have been brought up
for this behavior to be allowed. This patch simply removes this
limitation from all code paths that had checks for it and updates
the tests accordingly.
Reviewed-by: Jason King <jason.king@joyent.com>
Reviewed-by: Sean Eric Fagan <sef@ixsystems.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#8737Closes#8870
Redacted send/receive allows users to send subsets of their data to
a target system. One possible use case for this feature is to not
transmit sensitive information to a data warehousing, test/dev, or
analytics environment. Another is to save space by not replicating
unimportant data within a given dataset, for example in backup tools
like zrepl.
Redacted send/receive is a three-stage process. First, a clone (or
clones) is made of the snapshot to be sent to the target. In this
clone (or clones), all unnecessary or unwanted data is removed or
modified. This clone is then snapshotted to create the "redaction
snapshot" (or snapshots). Second, the new zfs redact command is used
to create a redaction bookmark. The redaction bookmark stores the
list of blocks in a snapshot that were modified by the redaction
snapshot(s). Finally, the redaction bookmark is passed as a parameter
to zfs send. When sending to the snapshot that was redacted, the
redaction bookmark is used to filter out blocks that contain sensitive
or unwanted information, and those blocks are not included in the send
stream. When sending from the redaction bookmark, the blocks it
contains are considered as candidate blocks in addition to those
blocks in the destination snapshot that were modified since the
creation_txg of the redaction bookmark. This step is necessary to
allow the target to rehydrate data in the case where some blocks are
accidentally or unnecessarily modified in the redaction snapshot.
The changes to bookmarks to enable fast space estimation involve
adding deadlists to bookmarks. There is also logic to manage the
life cycles of these deadlists.
The new size estimation process operates in cases where previously
an accurate estimate could not be provided. In those cases, a send
is performed where no data blocks are read, reducing the runtime
significantly and providing a byte-accurate size estimate.
Reviewed-by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: Prashanth Sreenivasa <pks@delphix.com>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: George Wilson <george.wilson@delphix.com>
Reviewed-by: Chris Williamson <chris.williamson@delphix.com>
Reviewed-by: Pavel Zhakarov <pavel.zakharov@delphix.com>
Reviewed-by: Sebastien Roy <sebastien.roy@delphix.com>
Reviewed-by: Prakash Surya <prakash.surya@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#7958
Trying to mount a dataset from a readonly pool could inadvertently start
the user accounting upgrade task, leading to the following failure:
VERIFY3(tx->tx_threads == 2) failed (0 == 2)
PANIC at txg.c:680:txg_wait_synced()
Showing stack for process 2541
CPU: 2 PID: 2541 Comm: z_upgrade Tainted: P O 3.16.0-4-amd64 #1 Debian 3.16.51-3
Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
Call Trace:
[<0>] ? dump_stack+0x5d/0x78
[<0>] ? spl_panic+0xc9/0x110 [spl]
[<0>] ? dnode_next_offset+0x1d4/0x2c0 [zfs]
[<0>] ? dmu_object_next+0x77/0x130 [zfs]
[<0>] ? dnode_rele_and_unlock+0x4d/0x120 [zfs]
[<0>] ? txg_wait_synced+0x91/0x220 [zfs]
[<0>] ? dmu_objset_id_quota_upgrade_cb+0x10f/0x140 [zfs]
[<0>] ? dmu_objset_upgrade_task_cb+0xe3/0x170 [zfs]
[<0>] ? taskq_thread+0x2cc/0x5d0 [spl]
[<0>] ? wake_up_state+0x10/0x10
[<0>] ? taskq_thread_should_stop.part.3+0x70/0x70 [spl]
[<0>] ? kthread+0xbd/0xe0
[<0>] ? kthread_create_on_node+0x180/0x180
[<0>] ? ret_from_fork+0x58/0x90
[<0>] ? kthread_create_on_node+0x180/0x180
This patch updates both functions responsible for checking if we can
perform user accounting to verify the pool is not readonly.
Reviewed-by: Alek Pinchuk <apinchuk@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#8424
zfs create, receive and rename can bypass this hierarchy rule. Update
both userland and kernel module to prevent this issue and use pyzfs
unit tests to exercise the ioctls directly.
Note: this commit slightly changes zfs_ioc_create() ABI. This allow to
differentiate a generic error (EINVAL) from the specific case where we
tried to create a dataset below a ZVOL (ZFS_ERR_WRONG_PARENT).
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
The boolean featureflags in use thus far in ZFS are extremely useful,
but because they take advantage of the zap layer, more interesting data
than just a true/false value can be stored in a featureflag. In redacted
send/receive, this is used to store the list of redaction snapshots for
a redacted dataset.
This change adds the ability for ZFS to store types other than a boolean
in a featureflag. The only other implemented type is a uint64_t array.
It also modifies the interfaces around dataset features to accomodate
the new capabilities, and adds a few new functions to increase
encapsulation.
This functionality will be used by the Redacted Send/Receive feature.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#7981
This change moves the bottom half of dmu_send.c (where the receive
logic is kept) into a new file, dmu_recv.c, and does similarly
for receive-related changes in header files.
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#7982
Since native ZFS encryption was merged, we have been fighting
against a series of bugs that come down to the same problem: Key
mappings (which must be present during all I/O operations) are
created and destroyed based on dataset ownership, but I/Os can
have traditionally been allowed to "leak" into the next txg after
the dataset is disowned.
In the past we have attempted to solve this problem by trying to
ensure that datasets are disowned ater all I/O is finished by
calling txg_wait_synced(), but we have repeatedly found edge cases
that need to be squashed and code paths that might incur a high
number of txg syncs. This patch attempts to resolve this issue
differently, by adding a reference to the key mapping for each txg
it is dirtied in. By doing so, we can remove many of the
unnecessary calls to txg_wait_synced() we have added in the past
and ensure we don't need to deal with this problem in the future.
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#7949
Allocation Classes add the ability to have allocation classes in a
pool that are dedicated to serving specific block categories, such
as DDT data, metadata, and small file blocks. A pool can opt-in to
this feature by adding a 'special' or 'dedup' top-level VDEV.
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Alek Pinchuk <apinchuk@datto.com>
Reviewed-by: Håkan Johansson <f96hajo@chalmers.se>
Reviewed-by: Andreas Dilger <andreas.dilger@chamcloud.com>
Reviewed-by: DHE <git@dehacked.net>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: Gregor Kopka <gregor@kopka.net>
Reviewed-by: Kash Pande <kash@tripleback.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Don Brady <don.brady@delphix.com>
Closes#5182
This patch fixes a bug where attempting to receive a send stream
with embedded data into an encrypted dataset would not cleanup
that dataset when the error was reached. The check was moved into
dmu_recv_begin_check(), preventing this issue.
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#7650
This project's goal is to make read-heavy channel programs and zfs(1m)
administrative commands faster by caching all the metadata that they will
need in the dbuf layer. This will prevent the data from being evicted, so
that any future call to i.e. zfs get all won't have to go to disk (very
much). There are two parts:
The dbuf_metadata_cache. We identify what to put into the cache based on
the object type of each dbuf. Caching objset properties os
{version,normalization,utf8only,casesensitivity} in the objset_t. The reason
these needed to be cached is that although they are queried frequently,
they aren't stored in a dbuf type which we can easily recognize and cache in
the dbuf layer; instead, we have to explicitly store them. There's already
existing infrastructure for maintaining cached properties in the objset
setup code, so I simply used that.
Performance Testing:
- Disabled kmem_flags
- Tuned dbuf_cache_max_bytes very low (128K)
- Tuned zfs_arc_max very low (64M)
Created test pool with 400 filesystems, and 100 snapshots per filesystem.
Later on in testing, added 600 more filesystems (with no snapshots) to make
sure scaling didn't look different between snapshots and filesystems.
Results:
| Test | Time (trunk / diff) | I/Os (trunk / diff) |
+------------------------+---------------------+---------------------+
| zpool import | 0:05 / 0:06 | 12.9k / 12.9k |
| zfs get all (uncached) | 1:36 / 0:53 | 16.7k / 5.7k |
| zfs get all (cached) | 1:36 / 0:51 | 16.0k / 6.0k |
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Thomas Caputi <tcaputi@datto.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Richard Lowe <richlowe@richlowe.net>
Ported-by: Alek Pinchuk <apinchuk@datto.com>
Signed-off-by: Alek Pinchuk <apinchuk@datto.com>
OpenZFS-issue: https://illumos.org/issues/9337
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/7dec52fCloses#7668
Datasets that are deeply nested (~100 levels) are impractical. We just
put a limit of 50 levels to newly created datasets. Existing datasets
should work without a problem.
The problem can be seen by attempting to create a dataset using the -p
option with many levels:
panic[cpu0]/thread=ffffff01cd282c20: BAD TRAP: type=8 (#df Double fault) rp=ffffffff
fffffffffbc3aa60 unix:die+100 ()
fffffffffbc3ab70 unix:trap+157d ()
ffffff00083d7020 unix:_patch_xrstorq_rbx+196 ()
ffffff00083d7050 zfs:dbuf_rele+2e ()
...
ffffff00083d7080 zfs:dsl_dir_close+32 ()
ffffff00083d70b0 zfs:dsl_dir_evict+30 ()
ffffff00083d70d0 zfs:dbuf_evict_user+4a ()
ffffff00083d7100 zfs:dbuf_rele_and_unlock+87 ()
ffffff00083d7130 zfs:dbuf_rele+2e ()
... The block above repeats once per directory in the ...
... create -p command, working towards the root ...
ffffff00083db9f0 zfs:dsl_dataset_drop_ref+19 ()
ffffff00083dba20 zfs:dsl_dataset_rele+42 ()
ffffff00083dba70 zfs:dmu_objset_prefetch+e4 ()
ffffff00083dbaa0 zfs:findfunc+23 ()
ffffff00083dbb80 zfs:dmu_objset_find_spa+38c ()
ffffff00083dbbc0 zfs:dmu_objset_find+40 ()
ffffff00083dbc20 zfs:zfs_ioc_snapshot_list_next+4b ()
ffffff00083dbcc0 zfs:zfsdev_ioctl+347 ()
ffffff00083dbd00 genunix:cdev_ioctl+45 ()
ffffff00083dbd40 specfs:spec_ioctl+5a ()
ffffff00083dbdc0 genunix:fop_ioctl+7b ()
ffffff00083dbec0 genunix:ioctl+18e ()
ffffff00083dbf10 unix:brand_sys_sysenter+1c9 ()
Porting notes:
* Added zfs_max_dataset_nesting module option with documentation.
* Updated zfs_rename_014_neg.ksh for Linux.
* Increase the zfs.sh stack warning to 15K. Enough time has passed
that 16K can be reasonably assumed to be the default value. It
was increased in the 3.15 kernel released in June of 2014.
Authored by: Serapheim Dimitropoulos <serapheim.dimitro@delphix.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Reviewed by: Matt Ahrens <matt@delphix.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Garrett D'Amore <garrett@damore.org>
OpenZFS-issue: https://www.illumos.org/issues/9330
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/757a75aCloses#7681
Commit torvalds/linux@95582b0 changes the inode i_atime, i_mtime,
and i_ctime members form timespec's to timespec64's to make them
2038 safe. As part of this change the current_time() function was
also updated to return the timespec64 type.
Resolve this issue by introducing a new inode_timespec_t type which
is defined to match the timespec type used by the inode. It should
be used when working with inode timestamps to ensure matching types.
The timestruc_t type under Illumos was used in a similar fashion but
was specified to always be a timespec_t. Rather than incorrectly
define this type all timespec_t types have been replaced by the new
inode_timespec_t type.
Finally, the kernel and user space 'sys/time.h' headers were aligned
with each other. They define as appropriate for the context several
constants as macros and include static inline implementation of
gethrestime(), gethrestime_sec(), and gethrtime().
Reviewed-by: Chunwei Chen <tuxoko@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7643
Minimal changes required to integrate the SPL sources in to the
ZFS repository build infrastructure and packaging.
Build system and packaging:
* Renamed SPL_* autoconf m4 macros to ZFS_*.
* Removed redundant SPL_* autoconf m4 macros.
* Updated the RPM spec files to remove SPL package dependency.
* The zfs package obsoletes the spl package, and the zfs-kmod
package obsoletes the spl-kmod package.
* The zfs-kmod-devel* packages were updated to add compatibility
symlinks under /usr/src/spl-x.y.z until all dependent packages
can be updated. They will be removed in a future release.
* Updated copy-builtin script for in-kernel builds.
* Updated DKMS package to include the spl.ko.
* Updated stale AUTHORS file to include all contributors.
* Updated stale COPYRIGHT and included the SPL as an exception.
* Renamed README.markdown to README.md
* Renamed OPENSOLARIS.LICENSE to LICENSE.
* Renamed DISCLAIMER to NOTICE.
Required code changes:
* Removed redundant HAVE_SPL macro.
* Removed _BOOT from nvpairs since it doesn't apply for Linux.
* Initial header cleanup (removal of empty headers, refactoring).
* Remove SPL repository clone/build from zimport.sh.
* Use of DEFINE_RATELIMIT_STATE and DEFINE_SPINLOCK removed due
to build issues when forcing C99 compilation.
* Replaced legacy ACCESS_ONCE with READ_ONCE.
* Include needed headers for `current` and `EXPORT_SYMBOL`.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
TEST_ZIMPORT_SKIP="yes"
Closes#7556
This commit introduces several changes:
* Update LICENSE and project information
* Give a good PEP8 talk to existing Python source code
* Add RPM/DEB packaging for pyzfs
* Fix some outstanding issues with the existing pyzfs code caused by
changes in the ABI since the last time the code was updated
* Integrate pyzfs Python unittest with the ZFS Test Suite
* Add missing libzfs_core functions: lzc_change_key,
lzc_channel_program, lzc_channel_program_nosync, lzc_load_key,
lzc_receive_one, lzc_receive_resumable, lzc_receive_with_cmdprops,
lzc_receive_with_header, lzc_reopen, lzc_send_resume, lzc_sync,
lzc_unload_key, lzc_remap
Note: this commit slightly changes zfs_ioc_unload_key() ABI. This allow
to differentiate the case where we tried to unload a key on a
non-existing dataset (ENOENT) from the situation where a dataset has
no key loaded: this is consistent with the "change" case where trying
to zfs_ioc_change_key() from a dataset with no key results in EACCES.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#7230
In the existing code, when doing a raw (encrypted) zfs receive,
we call arc_convert_to_raw() from open context. This creates a
race condition between arc_release()/arc_change_state() and
writing out the block from syncing context (arc_write_ready/done()).
This change makes it so that when we are doing a raw (encrypted)
zfs receive, we save the crypt parameters (salt, iv, mac) of dnode
blocks in the dbuf_dirty_record_t, and call arc_convert_to_raw()
from syncing context when writing out the block of dnodes.
Additionally, we can eliminate dr_raw and associated setters, and
instead know that dnode blocks are always raw when doing a zfs
receive (see the new field os_raw_receive).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#7424Closes#7429
OpenZFS 7614 - zfs device evacuation/removal
OpenZFS 9064 - remove_mirror should wait for device removal to complete
This project allows top-level vdevs to be removed from the storage pool
with "zpool remove", reducing the total amount of storage in the pool.
This operation copies all allocated regions of the device to be removed
onto other devices, recording the mapping from old to new location.
After the removal is complete, read and free operations to the removed
(now "indirect") vdev must be remapped and performed at the new location
on disk. The indirect mapping table is kept in memory whenever the pool
is loaded, so there is minimal performance overhead when doing operations
on the indirect vdev.
The size of the in-memory mapping table will be reduced when its entries
become "obsolete" because they are no longer used by any block pointers
in the pool. An entry becomes obsolete when all the blocks that use
it are freed. An entry can also become obsolete when all the snapshots
that reference it are deleted, and the block pointers that reference it
have been "remapped" in all filesystems/zvols (and clones). Whenever an
indirect block is written, all the block pointers in it will be "remapped"
to their new (concrete) locations if possible. This process can be
accelerated by using the "zfs remap" command to proactively rewrite all
indirect blocks that reference indirect (removed) vdevs.
Note that when a device is removed, we do not verify the checksum of
the data that is copied. This makes the process much faster, but if it
were used on redundant vdevs (i.e. mirror or raidz vdevs), it would be
possible to copy the wrong data, when we have the correct data on e.g.
the other side of the mirror.
At the moment, only mirrors and simple top-level vdevs can be removed
and no removal is allowed if any of the top-level vdevs are raidz.
Porting Notes:
* Avoid zero-sized kmem_alloc() in vdev_compact_children().
The device evacuation code adds a dependency that
vdev_compact_children() be able to properly empty the vdev_child
array by setting it to NULL and zeroing vdev_children. Under Linux,
kmem_alloc() and related functions return a sentinel pointer rather
than NULL for zero-sized allocations.
* Remove comment regarding "mpt" driver where zfs_remove_max_segment
is initialized to SPA_MAXBLOCKSIZE.
Change zfs_condense_indirect_commit_entry_delay_ticks to
zfs_condense_indirect_commit_entry_delay_ms for consistency with
most other tunables in which delays are specified in ms.
* ZTS changes:
Use set_tunable rather than mdb
Use zpool sync as appropriate
Use sync_pool instead of sync
Kill jobs during test_removal_with_operation to allow unmount/export
Don't add non-disk names such as "mirror" or "raidz" to $DISKS
Use $TEST_BASE_DIR instead of /tmp
Increase HZ from 100 to 1000 which is more common on Linux
removal_multiple_indirection.ksh
Reduce iterations in order to not time out on the code
coverage builders.
removal_resume_export:
Functionally, the test case is correct but there exists a race
where the kernel thread hasn't been fully started yet and is
not visible. Wait for up to 1 second for the removal thread
to be started before giving up on it. Also, increase the
amount of data copied in order that the removal not finish
before the export has a chance to fail.
* MMP compatibility, the concept of concrete versus non-concrete devices
has slightly changed the semantics of vdev_writeable(). Update
mmp_random_leaf_impl() accordingly.
* Updated dbuf_remap() to handle the org.zfsonlinux:large_dnode pool
feature which is not supported by OpenZFS.
* Added support for new vdev removal tracepoints.
* Test cases removal_with_zdb and removal_condense_export have been
intentionally disabled. When run manually they pass as intended,
but when running in the automated test environment they produce
unreliable results on the latest Fedora release.
They may work better once the upstream pool import refectoring is
merged into ZoL at which point they will be re-enabled.
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Alex Reece <alex@delphix.com>
Reviewed-by: George Wilson <george.wilson@delphix.com>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: Richard Laager <rlaager@wiktel.com>
Reviewed by: Tim Chase <tim@chase2k.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Garrett D'Amore <garrett@damore.org>
Ported-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Tim Chase <tim@chase2k.com>
OpenZFS-issue: https://www.illumos.org/issues/7614
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/f539f1ebCloses#6900
