This patch addresses multiple 'zpool import' block device
indentification problems which are most likely to occur on a
system configured to use blkid, by_vdev paths, multipath and
failover. The symptom most commonly observed is the import
uses different path names to import the pool than would
normally be expected.
* When using blkid to identify vdevs the listed devices may
be added to the cache in any order. In order to apply the
preferred search order heuristic a zfs_path_order() function
was added to calculate the order given full path names.
* Since it's possible to have multiple block devices with
different vdev guids which refer to the same ZPOOL_CONFIG_PATH
the slice cache must be indexed by guid and name. By avoiding
collisions the preferred ordering can be maintaining even
when multiple block devices claim the same ZPOOL_CONFIG_PATH.
The preferred sorting by partition was never benefitial for
a Linux system and was removed as part of this change.
* When adding entries to the blkid cache avl_find/avl_insert
are used instead of avl_add because collisions are possible
and must be handled gracefully.
* For pools using multipath devices there are, at a minimum,
three devices where a vdev label may be read. They are the
dm-* device and each underlying /dev/sd* device. Due to the
way the block cache is implemented each of these devices may
have a different cached copy of the vdev label. This can
result in "ghost pools" which appear to persist even after
a 'zpool labelclear' has been done to the dm-* device. In
order to prevent this the vdev label is read with O_DIRECT
in order to bypass any caching to get the on-disk version.
* When opening a block device verify that vdev guid read from
the disk matches the expected vdev guid. This allows for bad
labels to be filtered out.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#5359
Sometimes it is desirable to specifically disable one or several
features directly on the 'zpool create' command line.
$ zpool create -o feature@<feature>=disabled ...
Original-patch-by: Turbo Fredriksson <turbo@bayour.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#3460Closes#5142Closes#5324
Previously when a drive faulted, the statechange-led.sh script would lookup
the drive's LED sysfs entry in /sys/block/sd*/device/enclosure_device, and
turn it on. During testing we noticed that if you pulled out a drive, or if
the drive was so badly broken that it no longer appeared to Linux, that the
/sys/block/sd* path would be removed, and the script could not lookup the
LED entry.
To fix this, this patch looks up the disks's more persistent
"/sys/class/enclosure/X:X:X:X/Slot N" LED sysfs path at pool import. It then
passes that path to the statechange-led script to use, rather than having the
script look it up on the fly. This allows the script to turn on/off the slot
LEDs even when the drive is missing.
Closes#5309Closes#2375
1. Enable multipath autoreplace support for FMA.
This extends FMA autoreplace to work with multipath disks. This
requires libdevmapper to be installed at build time.
2. Turn on/off fault LEDs when VDEVs become degraded/faulted/online
Set ZED_USE_ENCLOSURE_LEDS=1 in zed.rc to have ZED turn on/off the enclosure
LED for a drive when a drive becomes FAULTED/DEGRADED. Your enclosure must
be supported by the Linux SES driver for this to work. The enclosure LED
scripts work for multipath devices as well. The scripts will clear the LED
when the fault is cleared.
3. Rate limit ZIO delay and checksum events so as not to flood ZED
ZIO delay and checksum events are rate limited to 5/sec in the zfs module.
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed by: Don Brady <don.brady@intel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#2449Closes#3017Closes#5159
coverity scan CID:147654,type: Copy into fixed size buffer
- string operation may write past the end of the fixed-size
destination buffer
coverity scan CID:147690,type: Uninitialized scalar variable
- call zfs_prop_get first in case we use sourcetype and
share_sourcetype without initialization
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: GeLiXin <ge.lixin@zte.com.cn>
Closes#5253
When the exception branch exits, the buf is leaked.
Reviewed by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: luozhengzheng <luo.zhengzheng@zte.com.cn>
Closes#5262
The following new test cases need to have execute permissions set:
userquota/groupspace_003_pos.ksh
userquota/userquota_013_pos.ksh
userquota/userspace_003_pos.ksh
upgrade/upgrade_userobj_001_pos.ksh
upgrade/setup.ksh
upgrade/cleanup.ksh
The following source files accidentally were marked executable:
lib/libzpool/kernel.c
lib/libshare/nfs.c
lib/libzfs/libzfs_dataset.c
lib/libzfs/libzfs_util.c
tests/zfs-tests/cmd/rm_lnkcnt_zero_file/rm_lnkcnt_zero_file.c
tests/zfs-tests/cmd/dir_rd_update/dir_rd_update.c
cmd/zed/zed_exec.c
module/icp/core/kcf_sched.c
module/zfs/dsl_pool.c
module/zfs/arc.c
module/nvpair/nvpair.c
man/man5/zfs-module-parameters.5
Reviewed-by: GeLiXin <ge.lixin@zte.com.cn>
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Reviewed-by: Jinshan Xiong <jinshan.xiong@intel.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#5241
Fixes ABI issues with fletcher4 code, adds support for
incremental updates, and adds ztest method for testing.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Chunwei Chen <david.chen@osnexus.com>
Signed-off-by: Gvozden Neskovic <neskovic@gmail.com>
Closes#5164
The variable snapprops_nvlist was never initialized, so properties
were not applied to the received snapshot.
Additionally, add zfs_receive_013_pos.ksh script to ZFS test suite to exercise
'zfs receive' functionality for user properties.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#4338
This patch tracks dnode usage for each user/group in the
DMU_USER/GROUPUSED_OBJECT ZAPs. ZAP entries dedicated to dnode
accounting have the key prefixed with "obj-" followed by the UID/GID
in string format (as done for the block accounting).
A new SPA feature has been added for dnode accounting as well as
a new ZPL version. The SPA feature must be enabled in the pool
before upgrading the zfs filesystem. During the zfs version upgrade,
a "quotacheck" will be executed by marking all dnode as dirty.
ZoL-bug-id: https://github.com/zfsonlinux/zfs/issues/3500
Signed-off-by: Jinshan Xiong <jinshan.xiong@intel.com>
Signed-off-by: Johann Lombardi <johann.lombardi@intel.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: Saso Kiselkov <saso.kiselkov@nexenta.com>
Reviewed by: Richard Lowe <richlowe@richlowe.net>
Approved by: Garrett D'Amore <garrett@damore.org>
Ported by: Tony Hutter <hutter2@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/4185
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/45818ee
Porting Notes:
This code is ported on top of the Illumos Crypto Framework code:
b5e030c8db
The list of porting changes includes:
- Copied module/icp/include/sha2/sha2.h directly from illumos
- Removed from module/icp/algs/sha2/sha2.c:
#pragma inline(SHA256Init, SHA384Init, SHA512Init)
- Added 'ctx' to lib/libzfs/libzfs_sendrecv.c:zio_checksum_SHA256() since
it now takes in an extra parameter.
- Added CTASSERT() to assert.h from for module/zfs/edonr_zfs.c
- Added skein & edonr to libicp/Makefile.am
- Added sha512.S. It was generated from sha512-x86_64.pl in Illumos.
- Updated ztest.c with new fletcher_4_*() args; used NULL for new CTX argument.
- In icp/algs/edonr/edonr_byteorder.h, Removed the #if defined(__linux) section
to not #include the non-existant endian.h.
- In skein_test.c, renane NULL to 0 in "no test vector" array entries to get
around a compiler warning.
- Fixup test files:
- Rename <sys/varargs.h> -> <varargs.h>, <strings.h> -> <string.h>,
- Remove <note.h> and define NOTE() as NOP.
- Define u_longlong_t
- Rename "#!/usr/bin/ksh" -> "#!/bin/ksh -p"
- Rename NULL to 0 in "no test vector" array entries to get around a
compiler warning.
- Remove "for isa in $($ISAINFO); do" stuff
- Add/update Makefiles
- Add some userspace headers like stdio.h/stdlib.h in places of
sys/types.h.
- EXPORT_SYMBOL *_Init/*_Update/*_Final... routines in ICP modules.
- Update scripts/zfs2zol-patch.sed
- include <sys/sha2.h> in sha2_impl.h
- Add sha2.h to include/sys/Makefile.am
- Add skein and edonr dirs to icp Makefile
- Add new checksums to zpool_get.cfg
- Move checksum switch block from zfs_secpolicy_setprop() to
zfs_check_settable()
- Fix -Wuninitialized error in edonr_byteorder.h on PPC
- Fix stack frame size errors on ARM32
- Don't unroll loops in Skein on 32-bit to save stack space
- Add memory barriers in sha2.c on 32-bit to save stack space
- Add filetest_001_pos.ksh checksum sanity test
- Add option to write psudorandom data in file_write utility
All users of fletcher4 methods must call `fletcher_4_init()/_fini()`
There's no benchmarking overhead when called from user-space.
Signed-off-by: Gvozden Neskovic <neskovic@gmail.com>
The error message in zpool_vdev_remove() said top-level devices
could be removed, but that has never been true.
Reported-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Laager <rlaager@wiktel.com>
Closes#4506Closes#5213
Authored by: Alex Deiter <alex.deiter@gmail.com>
Reviewed by: Alex Aizman alex.aizman@nexenta.com
Reviewed by: Alek Pinchuk alek.pinchuk@nexenta.com
Reviewed by: Roman Strashkin roman.strashkin@nexenta.com
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Garrett D'Amore <garrett@damore.org>
Ported-by: kernelOfTruth <kerneloftruth@gmail.com>
OpenZFS-issue: https://www.illumos.org/issues/6111
OpenZFS-commit: https://github.com/illumos/illumos-gate/commit/4a20c933Closes#5110
Porting notes:
There were changes from upstream due to the following commits:
- zfs send -p send properties only for snapshots that are actually sent
057485504e
- Produce a full snapshot list for zfs send -p
e890dd85a7
- Implement zfs_ioc_recv_new() for OpenZFS 2605
43e52eddb1
- OpenZFS 6314 - buffer overflow in dsl_dataset_name
ZFS_MAXNAMELEN was changed to the now used ZFS_MAX_DATASET_NAME_LEN since
eca7b76001
Fix misleading error message:
"The /dev/zfs device is missing and must be created.", if /etc/mtab is missing.
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Eric Desrochers <eric.desrochers@canonical.com>
Closes#4680Closes#5029
This first phase brings over the ZFS SLM module, zfs_mod.c, to handle
auto operations in response to disk events. Disk event monitoring is
provided from libudev and generates the expected payload schema for
zfs_mod. This work leverages the recently added devid and phys_path
strings in the vdev label.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@intel.com>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#4673
Always free mnpt memory on failure in the zfs_unmount() function.
In the zfs_unshare_proto() function mountpoint is a const and
should not be assigned.
Signed-off-by: cao.xuewen <cao.xuewen@zte.com.cn>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#5054
perf: 2.75x faster ddt_entry_compare()
First 256bits of ddt_key_t is a block checksum, which are expected
to be close to random data. Hence, on average, comparison only needs to
look at first few bytes of the keys. To reduce number of conditional
jump instructions, the result is computed as: sign(memcmp(k1, k2)).
Sign of an integer 'a' can be obtained as: `(0 < a) - (a < 0)` := {-1, 0, 1} ,
which is computed efficiently. Synthetic performance evaluation of
original and new algorithm over 1G random keys on 2.6GHz Intel(R) Xeon(R)
CPU E5-2660 v3:
old 6.85789 s
new 2.49089 s
perf: 2.8x faster vdev_queue_offset_compare() and vdev_queue_timestamp_compare()
Compute the result directly instead of using conditionals
perf: zfs_range_compare()
Speedup between 1.1x - 2.5x, depending on compiler version and
optimization level.
perf: spa_error_entry_compare()
`bcmp()` is not suitable for comparator use. Use `memcmp()` instead.
perf: 2.8x faster metaslab_compare() and metaslab_rangesize_compare()
perf: 2.8x faster zil_bp_compare()
perf: 2.8x faster mze_compare()
perf: faster dbuf_compare()
perf: faster compares in spa_misc
perf: 2.8x faster layout_hash_compare()
perf: 2.8x faster space_reftree_compare()
perf: libzfs: faster avl tree comparators
perf: guid_compare()
perf: dsl_deadlist_compare()
perf: perm_set_compare()
perf: 2x faster range_tree_seg_compare()
perf: faster unique_compare()
perf: faster vdev_cache _compare()
perf: faster vdev_uberblock_compare()
perf: faster fuid _compare()
perf: faster zfs_znode_hold_compare()
Signed-off-by: Gvozden Neskovic <neskovic@gmail.com>
Signed-off-by: Richard Elling <richard.elling@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#5033
This fix resolves warnings reported during compiling with different gcc
optimization levels in debug mode,
Test tools:
gcc version 4.4.7 20120313 (Red Hat 4.4.7-16) (GCC)
Linux version: 2.6.32-573.18.1.el6.x86_64, Red Hat Enterprise Linux Server release 6.1 (Santiago)
List of warnings:
CFLAGS=-O1 ./configure --enable-debug ;make
../../module/icp/core/kcf_sched.c: In function ‘kcf_aop_done’:
../../module/icp/core/kcf_sched.c:499: error: ‘fg’ may be used uninitialized in this function
../../module/icp/core/kcf_sched.c:499: note: ‘fg’ was declared here
CFLAGS=-Os ./configure --enable-debug ; make
libzfs_dataset.c: In function ‘zfs_prop_set_list’:
libzfs_dataset.c:1575: error: ‘nvl_len’ may be used uninitialized in this function
Signed-off-by: GeLiXin <ge.lixin@zte.com.cn>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#5022
If the loop index i comes to (ZFS_GET_NCOLS - 1), the cbp->cb_columns[i + 1]
actually read the data of cbp->cb_colwidths[0], which means the array
subscript is above array bounds.
Luckily the cbp->cb_colwidths[0] is always 0 and it seems we haven't
looped enough times to exceed the array bounds so far, but it's really
a secluded risk someday.
Signed-off-by: GeLiXin <ge.lixin@zte.com.cn>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#5003
- Benchmark memory block is increased to 128kiB to reflect real block sizes more
accurately. Measurements include all three stages needed for checksum generation,
i.e. `init()/compute()/fini()`. The inner loop is repeated multiple times to offset
overhead of time function.
- Fastest implementation selects native and byteswap methods independently in
benchmark. To support this new function pointers `init_byteswap()/fini_byteswap()`
are introduced.
- Implementation mutex lock is replaced by atomic variable.
- To save time, benchmark is not executed in userspace. Instead, highest supported
implementation is used for fastest. Default userspace selector is still 'cycle'.
- `fletcher_4_native/byteswap()` methods use incremental methods to finish
calculation if data size is not multiple of vector stride (currently 64B).
- Added `fletcher_4_native_varsize()` special purpose method for use when buffer size
is not known in advance. The method does not enforce 4B alignment on buffer size, and
will ignore last (size % 4) bytes of the data buffer.
- Benchmark `kstat` is changed to match the one of vdev_raidz. It now shows
throughput for all supported implementations (in B/s), native and byteswap,
as well as the code [fastest] is running.
Example of `fletcher_4_bench` running on `Intel(R) Xeon(R) CPU E5-2660 v3 @ 2.60GHz`:
implementation native byteswap
scalar 4768120823 3426105750
sse2 7947841777 4318964249
ssse3 7951922722 6112191941
avx2 13269714358 11043200912
fastest avx2 avx2
Example of `fletcher_4_bench` running on `Intel(R) Xeon Phi(TM) CPU 7210 @ 1.30GHz`:
implementation native byteswap
scalar 1291115967 1031555336
sse2 2539571138 1280970926
ssse3 2537778746 1080016762
avx2 4950749767 1078493449
avx512f 9581379998 4010029046
fastest avx512f avx512f
Signed-off-by: Gvozden Neskovic <neskovic@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4952
The indefinite article before nvlist should be "an", not "a".
We have 27 "an nvlist" and 7 "a nvlist" in our comment, they should
stay the same as we are such a strict filesystem.
Signed-off-by: GeLiXin <ge.lixin@zte.com.cn>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4941
This fix resolves warnings reported during compiling of user-space
libraries with different gcc optimization levels.
Tested with gcc versions: 4.9.2 (Debian), and 6.1.1 (Fedora).
The patch enables use of following opt levels: O0, O1, O2, O3, Og, Os, Ofast.
List of warnings:
[GCC 4.9.2 -Os]
libzfs_sendrecv.c:3726:26: error: 'clp' may be used uninitialized in this function [-Werror=maybe-uninitialized]
[GCC 4.9.2 -Og]
fs_fletcher.c:323:26: error: 'idx' may be used uninitialized in this function [-Werror=maybe-uninitialized]
dsl_dataset.c:1290:12: error: 'atp' may be used uninitialized in this function [-Werror=maybe-uninitialized]
[GCC 4.9.2 -Ofast]
u8_textprep.c:1310:9: error: 'tc[3ul]' may be used uninitialized in this function [-Werror=maybe-uninitialized]
u8_textprep.c:177:23: error: 'u8t[0ul]' may be used uninitialized in this function [-Werror=maybe-uninitialized]
dsl_dataset.c:2089:37: error: ‘hds’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
dsl_dataset.c:3216:2: error: ‘ds’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
dsl_dataset.c:1591:2: error: ‘ds’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
dsl_dataset.c:3341:2: error: ‘ds’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
vdev_raidz.c:1153:8: error: 'dcount[2]' may be used uninitialized in this function [-Werror=maybe-uninitialized]
vdev_raidz.c:1167:17: error: 'dst[2]' may be used uninitialized in this function [-Werror=maybe-uninitialized]
kernel.c:1005:2: error: ‘resid’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
libzfs_dataset.c:2826:8: error: ‘val’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
libzfs_dataset.c:3056:35: error: ‘val’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
libzfs_dataset.c:1584:13: error: ‘val’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
libzfs_dataset.c:3056:35: error: ‘val’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
libzfs_dataset.c:1792:66: error: ‘val’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
libzfs_dataset.c:3986:35: error: ‘val’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
[GCC 6.1.1]
Resolved in PR #4907
Signed-off-by: Gvozden Neskovic <neskovic@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4937
zfs_get_name() expects a parameter of type zfs_handle_t *zhp , but
gets an invalid parameter type of zfs_handle_t **zhp actually in
libzfs_dataset_cmp(), which may trigger a coredump if called.
libzfs_dataset_cmp() working normally so far, just because all the
callers only give datasets of type ZFS_TYPE_FILESYSTEM to it, we
compared their mountpoint and return, luckily.
Signed-off-by: GeLiXin <ge.lixin@zte.com.cn>
Signed-off-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4919
Config of a hot spare or l2cache device will leak memory in function
add_config(). At the start of this function, when dealing with a
config which belongs to a hot spare not currently in use or a l2cache
device the config should be freed.
Signed-off-by: liaoyuxiangqin <guo.yong33@zte.com.cn>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4910
In zpool_find_import_scan: Reads an uninitialized pointer or
its target Coverity #150966
Found by static analysis with CoverityScan 0.8.5
Signed-off-by: Gvozden Neskovic <neskovic@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4897
The switch statement in function zfs_standard_error_fmt for the
ENOSPC and EDQUOT cases returns immediately and unlike all other
cases in the switch this does not perform the va_end call.
Perform a break which ends up calling va_end rather than returning
immediately.
Found by static analysis with CoverityScan 0.8.5
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4900
Commit 519129f added support to multi-thread 'zpool import' for
the case where block devices are scanned for under /dev/. This
commit generalizes that logic and applies it to the case where
device names are acquired from libblkid.
The zpool_find_import_scan() and zpool_find_import_blkid()
functions create an AVL tree containing each device name. Each
entry in this tree is dispatched to a taskq where the function
zpool_open_func() validates the device by opening it and reading
the label. This may result in additional entries being added
to the tree and those device paths being verified.
This is largely how the upstream OpenZFS code behaves but due to
significant differences the non-Linux code has been dropped for
readability. Additionally, this code makes use of taskqs and
kmutexs which are normally not available to the command line tools.
Special care has been taken to allow their use in the import
functions.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#4794
Reviewed by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Yuri Pankov <yuri.pankov@nexenta.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Calling dsl_dataset_name on a dataset with a 256 byte buffer is asking
for trouble. We should check every dataset on import, using a 1024 byte
buffer and checking each time to see if the dataset's new name is longer
than 256 bytes.
OpenZFS-issue: https://www.illumos.org/issues/6876
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/ca8674e
Adds ZFS_IOC_RECV_NEW for resumable streams and preserves the legacy
ZFS_IOC_RECV user/kernel interface. The new interface supports all
stream options but is currently only used for resumable streams.
This way updated user space utilities will interoperate with older
kernel modules.
ZFS_IOC_RECV_NEW is modeled after the existing ZFS_IOC_SEND_NEW
handler. Non-Linux OpenZFS platforms have opted to change the
legacy interface in an incompatible fashion instead of adding a
new ioctl.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Authored by: Dan McDonald <danmcd@omniti.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Approved by: Gordon Ross <gordon.ross@nexenta.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/4986
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/5878fad
2605 want to resume interrupted zfs send
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed by: Xin Li <delphij@freebsd.org>
Reviewed by: Arne Jansen <sensille@gmx.net>
Approved by: Dan McDonald <danmcd@omniti.com>
Ported-by: kernelOfTruth <kerneloftruth@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/2605
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/9c3fd12
6980 6902 causes zfs send to break due to 32-bit/64-bit struct mismatch
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Ported by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/6980
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/ea4a67f
Porting notes:
- All rsend and snapshop tests enabled and updated for Linux.
- Fix misuse of input argument in traverse_visitbp().
- Fix ISO C90 warnings and errors.
- Fix gcc 'missing braces around initializer' in
'struct send_thread_arg to_arg =' warning.
- Replace 4 argument fletcher_4_native() with 3 argument version,
this change was made in OpenZFS 4185 which has not been ported.
- Part of the sections for 'zfs receive' and 'zfs send' was
rewritten and reordered to approximate upstream.
- Fix mktree xattr creation, 'user.' prefix required.
- Minor fixes to newly enabled test cases
- Long holds for volumes allowed during receive for minor registration.
Justification
-------------
This feature adds support for variable length dnodes. Our motivation is
to eliminate the overhead associated with using spill blocks. Spill
blocks are used to store system attribute data (i.e. file metadata) that
does not fit in the dnode's bonus buffer. By allowing a larger bonus
buffer area the use of a spill block can be avoided. Spill blocks
potentially incur an additional read I/O for every dnode in a dnode
block. As a worst case example, reading 32 dnodes from a 16k dnode block
and all of the spill blocks could issue 33 separate reads. Now suppose
those dnodes have size 1024 and therefore don't need spill blocks. Then
the worst case number of blocks read is reduced to from 33 to two--one
per dnode block. In practice spill blocks may tend to be co-located on
disk with the dnode blocks so the reduction in I/O would not be this
drastic. In a badly fragmented pool, however, the improvement could be
significant.
ZFS-on-Linux systems that make heavy use of extended attributes would
benefit from this feature. In particular, ZFS-on-Linux supports the
xattr=sa dataset property which allows file extended attribute data
to be stored in the dnode bonus buffer as an alternative to the
traditional directory-based format. Workloads such as SELinux and the
Lustre distributed filesystem often store enough xattr data to force
spill bocks when xattr=sa is in effect. Large dnodes may therefore
provide a performance benefit to such systems.
Other use cases that may benefit from this feature include files with
large ACLs and symbolic links with long target names. Furthermore,
this feature may be desirable on other platforms in case future
applications or features are developed that could make use of a
larger bonus buffer area.
Implementation
--------------
The size of a dnode may be a multiple of 512 bytes up to the size of
a dnode block (currently 16384 bytes). A dn_extra_slots field was
added to the current on-disk dnode_phys_t structure to describe the
size of the physical dnode on disk. The 8 bits for this field were
taken from the zero filled dn_pad2 field. The field represents how
many "extra" dnode_phys_t slots a dnode consumes in its dnode block.
This convention results in a value of 0 for 512 byte dnodes which
preserves on-disk format compatibility with older software.
Similarly, the in-memory dnode_t structure has a new dn_num_slots field
to represent the total number of dnode_phys_t slots consumed on disk.
Thus dn->dn_num_slots is 1 greater than the corresponding
dnp->dn_extra_slots. This difference in convention was adopted
because, unlike on-disk structures, backward compatibility is not a
concern for in-memory objects, so we used a more natural way to
represent size for a dnode_t.
The default size for newly created dnodes is determined by the value of
a new "dnodesize" dataset property. By default the property is set to
"legacy" which is compatible with older software. Setting the property
to "auto" will allow the filesystem to choose the most suitable dnode
size. Currently this just sets the default dnode size to 1k, but future
code improvements could dynamically choose a size based on observed
workload patterns. Dnodes of varying sizes can coexist within the same
dataset and even within the same dnode block. For example, to enable
automatically-sized dnodes, run
# zfs set dnodesize=auto tank/fish
The user can also specify literal values for the dnodesize property.
These are currently limited to powers of two from 1k to 16k. The
power-of-2 limitation is only for simplicity of the user interface.
Internally the implementation can handle any multiple of 512 up to 16k,
and consumers of the DMU API can specify any legal dnode value.
The size of a new dnode is determined at object allocation time and
stored as a new field in the znode in-memory structure. New DMU
interfaces are added to allow the consumer to specify the dnode size
that a newly allocated object should use. Existing interfaces are
unchanged to avoid having to update every call site and to preserve
compatibility with external consumers such as Lustre. The new
interfaces names are given below. The versions of these functions that
don't take a dnodesize parameter now just call the _dnsize() versions
with a dnodesize of 0, which means use the legacy dnode size.
New DMU interfaces:
dmu_object_alloc_dnsize()
dmu_object_claim_dnsize()
dmu_object_reclaim_dnsize()
New ZAP interfaces:
zap_create_dnsize()
zap_create_norm_dnsize()
zap_create_flags_dnsize()
zap_create_claim_norm_dnsize()
zap_create_link_dnsize()
The constant DN_MAX_BONUSLEN is renamed to DN_OLD_MAX_BONUSLEN. The
spa_maxdnodesize() function should be used to determine the maximum
bonus length for a pool.
These are a few noteworthy changes to key functions:
* The prototype for dnode_hold_impl() now takes a "slots" parameter.
When the DNODE_MUST_BE_FREE flag is set, this parameter is used to
ensure the hole at the specified object offset is large enough to
hold the dnode being created. The slots parameter is also used
to ensure a dnode does not span multiple dnode blocks. In both of
these cases, if a failure occurs, ENOSPC is returned. Keep in mind,
these failure cases are only possible when using DNODE_MUST_BE_FREE.
If the DNODE_MUST_BE_ALLOCATED flag is set, "slots" must be 0.
dnode_hold_impl() will check if the requested dnode is already
consumed as an extra dnode slot by an large dnode, in which case
it returns ENOENT.
* The function dmu_object_alloc() advances to the next dnode block
if dnode_hold_impl() returns an error for a requested object.
This is because the beginning of the next dnode block is the only
location it can safely assume to either be a hole or a valid
starting point for a dnode.
* dnode_next_offset_level() and other functions that iterate
through dnode blocks may no longer use a simple array indexing
scheme. These now use the current dnode's dn_num_slots field to
advance to the next dnode in the block. This is to ensure we
properly skip the current dnode's bonus area and don't interpret it
as a valid dnode.
zdb
---
The zdb command was updated to display a dnode's size under the
"dnsize" column when the object is dumped.
For ZIL create log records, zdb will now display the slot count for
the object.
ztest
-----
Ztest chooses a random dnodesize for every newly created object. The
random distribution is more heavily weighted toward small dnodes to
better simulate real-world datasets.
Unused bonus buffer space is filled with non-zero values computed from
the object number, dataset id, offset, and generation number. This
helps ensure that the dnode traversal code properly skips the interior
regions of large dnodes, and that these interior regions are not
overwritten by data belonging to other dnodes. A new test visits each
object in a dataset. It verifies that the actual dnode size matches what
was stored in the ztest block tag when it was created. It also verifies
that the unused bonus buffer space is filled with the expected data
patterns.
ZFS Test Suite
--------------
Added six new large dnode-specific tests, and integrated the dnodesize
property into existing tests for zfs allow and send/recv.
Send/Receive
------------
ZFS send streams for datasets containing large dnodes cannot be received
on pools that don't support the large_dnode feature. A send stream with
large dnodes sets a DMU_BACKUP_FEATURE_LARGE_DNODE flag which will be
unrecognized by an incompatible receiving pool so that the zfs receive
will fail gracefully.
While not implemented here, it may be possible to generate a
backward-compatible send stream from a dataset containing large
dnodes. The implementation may be tricky, however, because the send
object record for a large dnode would need to be resized to a 512
byte dnode, possibly kicking in a spill block in the process. This
means we would need to construct a new SA layout and possibly
register it in the SA layout object. The SA layout is normally just
sent as an ordinary object record. But if we are constructing new
layouts while generating the send stream we'd have to build the SA
layout object dynamically and send it at the end of the stream.
For sending and receiving between pools that do support large dnodes,
the drr_object send record type is extended with a new field to store
the dnode slot count. This field was repurposed from unused padding
in the structure.
ZIL Replay
----------
The dnode slot count is stored in the uppermost 8 bits of the lr_foid
field. The bits were unused as the object id is currently capped at
48 bits.
Resizing Dnodes
---------------
It should be possible to resize a dnode when it is dirtied if the
current dnodesize dataset property differs from the dnode's size, but
this functionality is not currently implemented. Clearly a dnode can
only grow if there are sufficient contiguous unused slots in the
dnode block, but it should always be possible to shrink a dnode.
Growing dnodes may be useful to reduce fragmentation in a pool with
many spill blocks in use. Shrinking dnodes may be useful to allow
sending a dataset to a pool that doesn't support the large_dnode
feature.
Feature Reference Counting
--------------------------
The reference count for the large_dnode pool feature tracks the
number of datasets that have ever contained a dnode of size larger
than 512 bytes. The first time a large dnode is created in a dataset
the dataset is converted to an extensible dataset. This is a one-way
operation and the only way to decrement the feature count is to
destroy the dataset, even if the dataset no longer contains any large
dnodes. The complexity of reference counting on a per-dnode basis was
too high, so we chose to track it on a per-dataset basis similarly to
the large_block feature.
Signed-off-by: Ned Bass <bass6@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#3542
The libzfs_graph.c source file should have been removed in 330d06f,
it is entirely unused.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4766
ZFS allows for specific permissions to be delegated to normal users
with the `zfs allow` and `zfs unallow` commands. In addition, non-
privileged users should be able to run all of the following commands:
* zpool [list | iostat | status | get]
* zfs [list | get]
Historically this functionality was not available on Linux. In order
to add it the secpolicy_* functions needed to be implemented and mapped
to the equivalent Linux capability. Only then could the permissions on
the `/dev/zfs` be relaxed and the internal ZFS permission checks used.
Even with this change some limitations remain. Under Linux only the
root user is allowed to modify the namespace (unless it's a private
namespace). This means the mount, mountpoint, canmount, unmount,
and remount delegations cannot be supported with the existing code. It
may be possible to add this functionality in the future.
This functionality was validated with the cli_user and delegation test
cases from the ZFS Test Suite. These tests exhaustively verify each
of the supported permissions which can be delegated and ensures only
an authorized user can perform it.
Two minor bug fixes were required for test-running.py. First, the
Timer() object cannot be safely created in a `try:` block when there
is an unconditional `finally` block which references it. Second,
when running as a normal user also check for scripts using the
both the .ksh and .sh suffixes.
Finally, existing users who are simulating delegations by setting
group permissions on the /dev/zfs device should revert that
customization when updating to a version with this change.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#362Closes#434Closes#4100Closes#4394Closes#4410Closes#4487
Add argument format to print_one_column(), and use it to call
zfs_nicenum_format with, instead of just zfs_nicenum. Don't print "%"
for fragmentation or capacity percent values.
The calls to print_one_colum is made with ZFS_NICENUM_RAW if
cb->cb_literal (zpool list called with -p), and ZFS_NICENUM_1024 if not.
Also zpool_get_prop is modified to don't add "%" or "x" if literal.
Signed-off-by: Christer Ekholm <che@chrekh.se>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov
Closes#4657
3993 zpool(1M) and zfs(1M) should support -p for "list" and "get"
4700 "zpool get" doesn't support -H or -o options
Reviewed by: Dan McDonald <danmcd@omniti.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Ported by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/3993
OpenZFS-issue: https://www.illumos.org/issues/4700
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/c58b352
Porting notes:
I removed ZoL's zpool_get_prop_literal() in favor of
zpool_get_prop(..., boolean_t literal) since that's what OpenZFS
uses. The functionality is the same.
Authored by: Chris Williamson <chris.williamson@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Ported-by: Denys Rtveliashvili <denys@rtveliashvili.name>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
lzc_destroy_snaps() returns an nvlist in errlist.
zfs_destroy_snaps_nvl() should nvlist_free() it before returning.
OpenZFS-issue: https://www.illumos.org/issues/6873
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/ee06391Closes#4614
Authored by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Ported-by: Denys Rtveliashvili <denys@rtveliashvili.name>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Incorrect endianness swap for drr_spill.drr_length in libzfs_sendrecv.c
Instead of drr_write.drr_length, we should be assigning the result of
the byteswap to drr_spill.drr_length.
OpenZFS-issue: https ://www.illumos.org/issues/6879
OpenZFS-commit: https ://github.com/openzfs/openzfs/commit/74c8720
Closes#4613
6659 nvlist_free(NULL) is a no-op
Reviewed by: Toomas Soome <tsoome@me.com>
Reviewed by: Marcel Telka <marcel@telka.sk>
Approved by: Robert Mustacchi <rm@joyent.com>
References:
https://www.illumos.org/issues/6659https://github.com/illumos/illumos-gate/commit/aab83bb
Ported-by: David Quigley <dpquigl@davequigley.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4566
When importing a pool using the blkid cache only the device
node path was added to the list of known paths for a device.
This results in 'zpool import' always using the sdX names
in preference to the 'path' name stored in the label.
To fix the issue the blkid import path has been updated to
add both the 'path', 'devid', and 'devname' names from the
label to the known paths. A sanity check is done to ensure
these paths do refer to the same device identified by blkid.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#4523Closes#3043
When ZFS partitions a block device it must wait for udev to create
both a device node and all the device symlinks. This process takes
a variable length of time and depends on factors such how many links
must be created, the complexity of the rules, etc. Complicating
the situation further it is not uncommon for udev to create and
then remove a link multiple times while processing the udev rules.
Given the above, the existing scheme of waiting for an expected
partition to appear by name isn't 100% reliable. At this point
udev may still remove and recreate think link resulting in the
kernel modules being unable to open the device.
In order to address this the zpool_label_disk_wait() function
has been updated to use libudev. Until the registered system
device acknowledges that it in fully initialized the function
will wait. Once fully initialized all device links are checked
and allowed to settle for 50ms. This makes it far more likely
that all the device nodes will exist when the kernel modules
need to open them.
For systems without libudev an alternate zpool_label_disk_wait()
was updated to include a settle time. In addition, the kernel
modules were updated to include retry logic for this ENOENT case.
Due to the improved checks in the utilities it is unlikely this
logic will be invoked. However, if the rare event it is needed
it will prevent a failure.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Richard Laager <rlaager@wiktel.com>
Closes#4523Closes#3708Closes#4077Closes#4144Closes#4214Closes#4517
When partitioning a device a name may be specified for each partition.
Internally zfs doesn't use this partition name for anything so it
has always just been set to "zfs".
However this isn't optimal because udev will create symlinks using
this name in /dev/disk/by-partlabel/. If the name isn't unique
then all the links cannot be created.
Therefore a random 64-bit value has been added to the partition
label, i.e "zfs-1234567890abcdef". Additional information could
be encoded here but since partitions may be reused that might
result in confusion and it was decided against.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Richard Laager <rlaager@wiktel.com>
Closes#4517
Current zpool import code skips directory entries which have prefixes
similar to some system files on linux such as "fd", "core" etc. However,
this means one cannot have one's zpools hosted inside files which are named
e.g. core-1 or lp. Furthermore, apart from the string checks there is already
which makes the zpool_open_func work only with regular files and block devices.
To fix this problem remove most of the checks since they are redundant but
leave the checks for the 'hpet' and 'watchdog' names. Furthermore, change
the checks to strcmp which albeit less safe than strncmp allows to have
devices whose names are prefixed by 'hpet' or 'watchdog'.
Signed-off-by: Nikolay Borisov <kernel@kyup.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4438
Also enable lazytime in mount.zfs
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #4482
This is foundational work for ZED.
Updates a leaf vdev's persistent device strings on Linux platform
* only applies for a dedicated leaf vdev (aka whole disk)
* updated during pool create|add|attach|import
* used for matching device matching during auto-{online,expand,replace}
* stored in a leaf disk config label (i.e. alongside 'path' NVP)
* can opt-out using env var ZFS_VDEV_DEVID_OPT_OUT=YES
Some examples:
path: '/dev/sdb1'
devid: 'scsi-350000394a8ca4fbc-part1'
phys_path: 'pci-0000:04:00.0-sas-0x50000394a8ca4fbf-lun-0'
path: '/dev/mapper/mpatha'
devid: 'dm-uuid-mpath-35000c5006304de3f'
Signed-off-by: Don Brady <don.brady@intel.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2856Closes#3978Closes#4416
This issue was caused by calling `thread_init()` and `thread_fini()`
multiple times resulting in `kthread_key` being invalid. To resolve
the issue the explicit calls to `thread_init()` and `thread_fini()`
required by the `zpool` command have been moved in to the command.
Consumers such as `zdb` and `zhack` perform the same initialized
through `kernel_init()` and `kernel_fini()`.
Resolving this issue allows multiple additional test cases to
be enabled.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Signed-off-by: Chunwei Chen <tuxoko@gmail.com>
Signed-off-by: Tim Chase <tim@chase2k.com>
Closes#4331
I noticed during code review of zfsonlinux/zfs#4385 that the author of a
commit had peppered the various Makefile.am files with `$(TIRPC_LIBS)`
when putting it into `lib/libspl/Makefile.am` should have sufficed. Upon
further examination, it seems that he had copied what we do with
`$(ZLIB)`. We also have a bit of that with `-ldl` too. Unfortunately,
what we do is wrong, so lets fix it to set a good example for future
contributors.
In addition, we have multiple `-lz` and `-luuid` passed to the compiler
because each `AC_CHECK_LIB` adds it to `$LIBS`. That is somewhat
annoying to see, so we switch to `AC_SEARCH_LIBS` to avoid it. This is
consistent with the recommendation to use `AC_SEARCH_LIBS` over
`AC_CHECK_LIB` by autotools upstream:
https://www.gnu.org/software/autoconf/manual/autoconf-2.66/html_node/Libraries.html
In an ideal world, this would translate into improvements in ELF's
`DT_NEEDED` entries, but that is not the case because of a couple of
bugs in libtool.
The first bug causes libtool to overlink by using static link
dependencies for dynamic linking:
https://wiki.mageia.org/en/Overlinking_issues_in_packaging#libtool_issues
The workaround for this should be to pass `-Wl,--as-needed` in
`LDFLAGS`. That leads us to the second bug, where libtool passes
`LDFLAGS` after the libraries are specified and `ld` will only honor
`--as-needed` on libraries specified before it:
https://sigquit.wordpress.com/2011/02/16/why-asneeded-doesnt-work-as-expected-for-your-libraries-on-your-autotools-project/
There are a few possible workarounds for the second bug. One is to
either patch the compiler spec file to specify `-Wl,--as-needed` or pass
`-Wl,--as-needed` via `CC` like `CC='gcc -Wl,--as-needed'` so that it is
specified early. Another is to patch ltmain.sh like Gentoo does:
https://gitweb.gentoo.org/repo/gentoo.git/tree/eclass/ELT-patches/as-needed
Without one of those workarounds, this cleanup provides no benefit in
terms of `DT_NEEDED` entry generation. It should still be an improvement
because it nicely simplifies the code while encouraging good habits when
patching autotools scripts.
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4426
Add the ZFS Test Suite and test-runner framework from illumos.
This is a continuation of the work done by Turbo Fredriksson to
port the ZFS Test Suite to Linux. While this work was originally
conceived as a stand alone project integrating it directly with
the ZoL source tree has several advantages:
* Allows the ZFS Test Suite to be packaged in zfs-test package.
* Facilitates easy integration with the CI testing.
* Users can locally run the ZFS Test Suite to validate ZFS.
This testing should ONLY be done on a dedicated test system
because the ZFS Test Suite in its current form is destructive.
* Allows the ZFS Test Suite to be run directly in the ZoL source
tree enabled developers to iterate quickly during development.
* Developers can easily add/modify tests in the framework as
features are added or functionality is changed. The tests
will then always be in sync with the implementation.
Full documentation for how to run the ZFS Test Suite is available
in the tests/README.md file.
Warning: This test suite is designed to be run on a dedicated test
system. It will make modifications to the system including, but
not limited to, the following.
* Adding new users
* Adding new groups
* Modifying the following /proc files:
* /proc/sys/kernel/core_pattern
* /proc/sys/kernel/core_uses_pid
* Creating directories under /
Notes:
* Not all of the test cases are expected to pass and by default
these test cases are disabled. The failures are primarily due
to assumption made for illumos which are invalid under Linux.
* When updating these test cases it should be done in as generic
a way as possible so the patch can be submitted back upstream.
Most existing library functions have been updated to be Linux
aware, and the following functions and variables have been added.
* Functions:
* is_linux - Used to wrap a Linux specific section.
* block_device_wait - Waits for block devices to be added to /dev/.
* Variables: Linux Illumos
* ZVOL_DEVDIR "/dev/zvol" "/dev/zvol/dsk"
* ZVOL_RDEVDIR "/dev/zvol" "/dev/zvol/rdsk"
* DEV_DSKDIR "/dev" "/dev/dsk"
* DEV_RDSKDIR "/dev" "/dev/rdsk"
* NEWFS_DEFAULT_FS "ext2" "ufs"
* Many of the disabled test cases fail because 'zfs/zpool destroy'
returns EBUSY. This is largely causes by the asynchronous nature
of device handling on Linux and is expected, the impacted test
cases will need to be updated to handle this.
* There are several test cases which have been disabled because
they can trigger a deadlock. A primary example of this is to
recursively create zpools within zpools. These tests have been
disabled until the root issue can be addressed.
* Illumos specific utilities such as (mkfile) should be added to
the tests/zfs-tests/cmd/ directory. Custom programs required by
the test scripts can also be added here.
* SELinux should be either is permissive mode or disabled when
running the tests. The test cases should be updated to conform
to a standard policy.
* Redundant test functionality has been removed (zfault.sh).
* Existing test scripts (zconfig.sh) should be migrated to use
the framework for consistency and ease of testing.
* The DISKS environment variable currently only supports loopback
devices because of how the ZFS Test Suite expects partitions to
be named (p1, p2, etc). Support must be added to generate the
correct partition name based on the device location and name.
* The ZFS Test Suite is part of the illumos code base at:
https://github.com/illumos/illumos-gate/tree/master/usr/src/test
Original-patch-by: Turbo Fredriksson <turbo@bayour.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#6Closes#1534
Added by-partlabel and by-partuuid to the default device search
path. Made made device names in by-label more preferable.
Signed-off-by: Thijs Cramer <thijs.cramer@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#3892
Historically libblkid support was detected as part of configure
and optionally enabled. This was done because at the time support
for detecting ZFS pool vdevs had just be added to libblkid and
those updated packages were not yet part of many distributions.
This is no longer the case and any reasonably current distribution
will ship a version of libblkid which can detect ZFS pool vdevs.
This patch makes libblkid mandatory at build time and libblkid
the preferred method of scanning for ZFS pools. For distributions
which include a modern version of libblkid there is no change in
behavior. Explicitly scanning the default search paths is still
supported and can be enabled with the '-s' command line option.
Additionally making libblkid mandatory means that the 'zpool create'
command can reliably detect if a specified device has an existing
non-ZFS filesystem (ext4, xfs) and print a warning.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2448
print_vdev_stats() subtracts the old bandwidth/ops stats from the new stats
to calculate the bandwidth/ops numbers in "zpool iostat". However when the
TXG numbers change between stats, zpool_refresh_stats() will incorrectly assign
a NULL to the old stats. This causes print_vdev_stats() to use zeroes for
the old bandwidth/ops numbers, resulting in an inaccurate calculation.
This fix allows the calculation to happen even when TXGs change.
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4387
The following options have been added to the zpool add, iostat,
list, status, and split subcommands. The default behavior was
not modified, from zfs(8).
-g Display vdev GUIDs instead of the normal short
device names. These GUIDs can be used in-place of
device names for the zpool detach/off‐
line/remove/replace commands.
-L Display real paths for vdevs resolving all symbolic
links. This can be used to lookup the current block
device name regardless of the /dev/disk/ path used
to open it.
-p Display full paths for vdevs instead of only the
last component of the path. This can be used in
conjunction with the -L flag.
This behavior may also be enabled using the following environment
variables.
ZPOOL_VDEV_NAME_GUID
ZPOOL_VDEV_NAME_FOLLOW_LINKS
ZPOOL_VDEV_NAME_PATH
This change is based on worked originally started by Richard Yao
to add a -g option. Then extended by @ilovezfs to add a -L option
for openzfsonosx. Those changes have been merged, re-factored,
a -p option added and extended to all relevant zpool subcommands.
Original-patch-by: Richard Yao <ryao@gentoo.org>
Extended-by: ilovezfs <ilovezfs@icloud.com>
Extended-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: ilovezfs <ilovezfs@icloud.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2011Closes#4341
When extracting tokens from the string strtok(2) is allowed to modify
the passed buffer. Therefore the zfs_strcmp_pathname() function must
make a copy of the passed string before passing it to strtok(3).
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@intel.com>
Closes#4312
1778 Assertion failed: rn->rn_nozpool == B_FALSE
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <george@delphix.com>
Reviewed by: Richard Elling <richard.elling@richardelling.com>
Approved by: Gordon Ross <gordon.ross@nexenta.com>
References:
https://www.illumos.org/issues/1778https://github.com/illumos/illumos-gate/commit/bd0f709
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
5518 Memory leaks in libzfs import implementation
Reviewed by: Dan Fields <dan.fields@nexenta.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Serghei Samsi <sscdvp@gmail.com>
Approved by: Dan McDonald <danmcd@omniti.com>
References:
https://www.illumos.org/issues/5518https://github.com/illumos/illumos-gate/commit/078266a
Porting notes:
- One hunk of this change was already applied independently in
commit 4def05f.
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
6815179 zpool import with a large number of LUNs is too slow
6844191 zpool import, scanning of disks should be multi-threaded
References:
https://github.com/illumos/illumos-gate/commit/4f67d75
Porting notes:
- This change was originally never ported to Linux due to it
dependence on the thread pool interface. This patch solves
that issue by switching the code to use the existing taskq
implementation which provides the same basic functionality.
However, in order for this to work properly thread_init()
and thread_fini() must be called around to taskq consumer
to perform the needed thread initialization.
- The check_one_slice, nozpool_all_slices, and check_slices
functions have been disabled for Linux. They are difficult,
but possible, to implement for Linux due to how partitions
are get names. Since this is only an optimization this code
can be added at a latter date.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
4953 zfs rename <snapshot> need not involve libshare
4954 "zfs create" need not involve libshare if we are not sharing
4955 libshare's get_zfs_dataset need not sort the datasets
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Sebastien Roy <sebastien.roy@delphix.com>
Reviewed by: Dan McDonald <danmcd@omniti.com>
Reviewed by: Gordon Ross <gordon.ross@nexenta.com>
Approved by: Garrett D'Amore <garrett@damore.org>
References:
https://www.illumos.org/issues/4953https://www.illumos.org/issues/4954https://www.illumos.org/issues/4955https://github.com/illumos/illumos-gate/commit/33cde0d
Porting notes:
- Dropped qsort libshare_zfs.c hunk, no equivalent ZoL code.
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4219
6298 zfs_create_008_neg and zpool_create_023_neg need to be updated
for large block support
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
References:
https://www.illumos.org/issues/6298https://github.com/illumos/illumos-gate/commit/e9316f7
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4217
3557 dumpvp_size is not updated correctly when a dump zvol's size is changed
3558 setting the volsize on a dump device does not return back ENOSPC
3559 setting a volsize larger than the space available sometimes succeeds
3560 dumpadm should be able to remove a dump device
Reviewed by: Adam Leventhal <ahl@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Christopher Siden <christopher.siden@delphix.com>
Approved by: Albert Lee <trisk@nexenta.com>
References:
https://www.illumos.org/issues/3559https://github.com/illumos/illumos-gate/commit/c61ea56
Porting notes:
- Internal zvol.c changes not applied due to implementation differences.
The external interface and behavior was already consistent with the
latest upstream code.
- Retired 2.6.28 HAVE_CHECK_DISK_SIZE_CHANGE configure check. All
supported kernels (2.6.32 and newer) provide this interface.
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4217
6280 libzfs: unshare_one() could fail with EZFS_SHARENFSFAILED
Reviewed by: Toomas Soome <tsoome@me.com>
Reviewed by: Dan McDonald <danmcd@omniti.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Approved by: Gordon Ross <gwr@nexenta.com>
References:
https://www.illumos.org/issues/6280https://github.com/illumos/illumos-gate/commit/d1672ef
Ported-by: kernelOfTruth kerneloftruth@gmail.com
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
6358 A faulted pool with only unavailable vdevs triggers assertion
failure in libzfs
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Andrew Stormont <andyjstormont@gmail.com>
Reviewed by: Serban Maduta <serban.maduta@gmail.com>
Approved by: Dan McDonald <danmcd@omniti.com>
References:
https://illumos.org/issues/6358https://github.com/illumos/illumos-gate/commit/b289d04
Ported-by: kernelOfTruth kerneloftruth@gmail.com
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
5745 zfs set allows only one dataset property to be set at a time
Reviewed by: Christopher Siden <christopher.siden@delphix.com>
Reviewed by: George Wilson <george@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Bayard Bell <buffer.g.overflow@gmail.com>
Reviewed by: Richard PALO <richard@NetBSD.org>
Reviewed by: Steven Hartland <killing@multiplay.co.uk>
Approved by: Rich Lowe <richlowe@richlowe.net>
References:
https://www.illumos.org/issues/5745https://github.com/illumos/illumos-gate/commit/3092556
Porting notes:
- Fix the missing braces around initializer, zfs_cmd_t zc = {"\0"};
- Remove extra format argument in zfs_do_set()
- Declare at the top:
- zfs_prop_t prop;
- nvpair_t *elem;
- nvpair_t *next;
- int i;
- Additionally initialize:
- int added_resv = 0;
- zfs_prop_t prop = 0;
- Assign 0 install of NULL for uint64_t types.
- zc->zc_nvlist_conf = '\0';
- zc->zc_nvlist_src = '\0';
- zc->zc_nvlist_dst = '\0';
Ported-by: kernelOfTruth kerneloftruth@gmail.com
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#3574
As of gcc 5.1.1 20150618 (Red Hat 5.1.1-4) the -Werror=maybe-uninitialized
check detects that 'snapname' in recv_incremental_replication() may not be
initialized. Explicitly initialize the variable to resolved the warning.
libzfs_sendrecv.c: In function ‘recv_incremental_replication’:
libzfs_sendrecv.c:2019:2: error: ‘snapname’ may be used uninitialized in
(void) snprintf(buf, sizeof (buf), "%s@%s", fsname, snapname);
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
EDOM may occur if a user tries to set `recordsize` too large without
use "zfs set". This can be demonstrated with:
> zpool create testpool -O recordsize=32M /dev/...
Signed-off-by: DHE <git@dehacked.net>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#3911
ZFS incorrectly uses directory-based extended attributes even when
xattr=sa is specified as a dataset property or mount option. Support to
honor temporary mount options including "xattr" was added in commit
0282c4137e. There are two issues with the
mount option handling:
* Libzfs has historically included "xattr" in its list of default mount
options. This overrides the dataset property, so the dataset is always
configured to use directory-based xattrs even when the xattr dataset
property is set to off or sa. Address this by removing "xattr" from
the set of default mount options in libzfs.
* There was no way to enable system attribute-based extended attributes
using temporary mount options. Add the mount options "saxattr" and
"dirxattr" which enable the xattr behavior their names suggest. This
approach has the advantages of mirroring the valid xattr dataset
property values and following existing conventions for mount option
names.
Signed-off-by: Ned Bass <bass6@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#3787
Add the required kernel side infrastructure to parse arbitrary
mount options. This enables us to support temporary mount
options in largely the same way it is handled on other platforms.
See the 'Temporary Mount Point Properties' section of zfs(8)
for complete details.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#985Closes#3351
Since ZoL allows large blocks to be used by volumes, unlike upstream
illumos, the feature flag must be checked prior to volume creation.
This is critical because unlike filesystems, volumes will create a
object which uses large blocks as part of the create. Therefore, it
cannot be safely checked in zfs_check_settable() after the dataset
can been created.
In addition this patch updates the relevant error messages to use
zfs_nicenum() to print the maximum blocksize.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#3591
Build products from an out of tree build should be written
relative to the build directory. Sources should be referred
to by their locations in the source directory.
This is accomplished by adding the 'src' and 'obj' variables
for the module Makefile.am, using relative paths to reference
source files, and by setting VPATH when source files are not
co-located with the Makefile. This enables the following:
$ mkdir build
$ cd build
$ ../configure \
--with-spl=$HOME/src/git/spl/ \
--with-spl-obj=$HOME/src/git/spl/build
$ make -s
This change also has the advantage of resolving the following
warning which is generated by modern versions of automake.
Makefile.am:00: warning: source file 'xxx' is in a subdirectory,
Makefile.am:00: but option 'subdir-objects' is disabled
Signed-off-by: Turbo Fredriksson <turbo@bayour.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1082
We fail to make partitions on xvd (Xen Virtual Block) devices. This also
causes debug builds of zpool create to return an error when given xen
virtual block devices. These devices should be given the same treatment
as vd (KVM Virtual Block) devices, so we adjust the relevant code paths.
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#3576
All fprintf() error messages are moved out of the libzfs_init()
library function where they never belonged in the first place. A
libzfs_error_init() function is added to provide useful error
messages for the most common causes of failure.
Additionally, in libzfs_run_process() the 'rc' variable was renamed
to 'error' for consistency with the rest of the code base.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chris Dunlap <cdunlap@llnl.gov>
Signed-off-by: Richard Yao <ryao@gentoo.org>
While module loading itself is synchronous the creation of the /dev/zfs
device is not. This is because /dev/zfs is typically created by a udev
rule after the module is registered and presented to user space through
sysfs. This small window between module loading and device creation
can result in spurious failures of libzfs_init().
This patch closes that race by extending libzfs_init() so it can detect
that the modules are loaded and only if required wait for the /dev/zfs
device to be created. This allows scripts to reliably use the following
shell construct without the need for additional error handling.
$ /sbin/modprobe zfs && /sbin/zpool import -a
To minimize the potential time waiting in libzfs_init() a strategy
similar to adaptive mutexes is employed. The function will busy-wait
for up to 10ms based on the expectation that the modules were just
loaded and therefore the /dev/zfs will be created imminently. If it
takes longer than this it will fall back to polling for up to 10 seconds.
This behavior can be customized to some degree by setting the following
new environment variables. This functionality is provided for backwards
compatibility with existing scripts which depend on the module auto-load
behavior. By default module auto-loading is now disabled.
* ZFS_MODULE_LOADING="YES|yes|ON|on" - Attempt to load modules.
* ZFS_MODULE_TIMEOUT="<seconds>" - Seconds to wait for /dev/zfs
The zfs-import-* systemd service files have been updated to call
'/sbin/modprobe zfs' so they no longer rely on the legacy auto-loading
behavior.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chris Dunlap <cdunlap@llnl.gov>
Signed-off-by: Richard Yao <ryao@gentoo.org>
Closes#2556
Prefixing an octal value with a leading zero is the standard way
to disambiguate it. This change only impacts the `zfs diff` output
and is therefore very limited in scope.
Signed-off-by: Hajo M<C3><B6>ller <dasjoe@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#3417
5027 zfs large block support
Reviewed by: Alek Pinchuk <pinchuk.alek@gmail.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Josef 'Jeff' Sipek <josef.sipek@nexenta.com>
Reviewed by: Richard Elling <richard.elling@richardelling.com>
Reviewed by: Saso Kiselkov <skiselkov.ml@gmail.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Dan McDonald <danmcd@omniti.com>
References:
https://www.illumos.org/issues/5027https://github.com/illumos/illumos-gate/commit/b515258
Porting Notes:
* Included in this patch is a tiny ISP2() cleanup in zio_init() from
Illumos 5255.
* Unlike the upstream Illumos commit this patch does not impose an
arbitrary 128K block size limit on volumes. Volumes, like filesystems,
are limited by the zfs_max_recordsize=1M module option.
* By default the maximum record size is limited to 1M by the module
option zfs_max_recordsize. This value may be safely increased up to
16M which is the largest block size supported by the on-disk format.
At the moment, 1M blocks clearly offer a significant performance
improvement but the benefits of going beyond this for the majority
of workloads are less clear.
* The illumos version of this patch increased DMU_MAX_ACCESS to 32M.
This was determined not to be large enough when using 16M blocks
because the zfs_make_xattrdir() function will fail (EFBIG) when
assigning a TX. This was immediately observed under Linux because
all newly created files must have a security xattr created and
that was failing. Therefore, we've set DMU_MAX_ACCESS to 64M.
* On 32-bit platforms a hard limit of 1M is set for blocks due
to the limited virtual address space. We should be able to relax
this one the ABD patches are merged.
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#354
The umem_alloc_aligned() function should not assume that a 'void *'
type is 64-bit. It will not be on 32-bit platforms. Rather than
complicating the ASSERT to handle this it is simply removed.
Additionally, the '%lu' format specifier should not be assumed to
imply a 64-bit value. Fix this by using the 'llu' format specifier
which will always be atleast 64-bit and explicitly casing the
variable to an u_longlong_t. This issue is handled the same way
in many other parts of the code.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
3897 zfs filesystem and snapshot limits
Author: Jerry Jelinek <jerry.jelinek@joyent.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Approved by: Christopher Siden <christopher.siden@delphix.com>
References:
https://www.illumos.org/issues/3897https://github.com/illumos/illumos-gate/commit/a2afb61
Porting Notes:
dsl_dataset_snapshot_check(): reduce stack usage using kmem_alloc().
Ported-by: Chris Dunlop <chris@onthe.net.au>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
As of this commit, volumes do not possess the version property in
any existing OpenZFS implementation. The zpool upgrade code, however,
uses zfs_prop_get_int() to fetch the version property of all children in
a pool. The semantics of the function, however, demand that it only be
used for known valid properties so it returns a garbage value for volumes.
This patch causes the version of a volume to appear to callers using
the zfs_prop_get_int() API to be that of the default ZPL version for
the implementation. In the future, should volumes gain the property,
its actual value will be used.
Signed-off-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Fixes#3313
Make the 'zpool import' command honor the overlay property to allow
filesystems to be mounted on a non-empty directory. As it stands now
this property is only checked by the 'zfs mount' command. Move the
check into 'zfs_mount()` in libzpool so the property is honored for all
callers.
Signed-off-by: Ned Bass <bass6@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#3227
When using 'zpool import' to scan for available pools prefer vdev names
which reference vdevs with more valid labels. There should be two labels
at the start of the device and two labels at the end of the device. If
labels are missing then the device has been damaged or is in some other
way incomplete. Preferring names with fully intact labels helps weed out
bad paths and improves the likelihood of being able to import the pool.
This behavior only applies when scanning /dev/ for valid pools. If a
cache file exists the pools described by the cache file will be used.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chris Dunlap <cdunlap@llnl.gov>
Closes#3145Closes#2844Closes#3107
I noticed when reviewing documentation that it is possible for user
space to use fctnl(fd, F_SETPIPE_SZ, (unsigned long) size) to change
the kernel pipe buffer size on Linux to increase the pipe size up to
the value specified in /proc/sys/fs/pipe-max-size. There are users using
mbuffer to improve zfs recv performance when piping over the network, so
it seems advantageous to integrate such functionality directly into the
zfs recv tool. This avoids the addition of two buffers and two copies
(one for the buffer mbuffer adds and another for the additional pipe),
so it should be more efficient.
This could have been made configurable and/or this could have changed
the value back to the original after we were done with the file
descriptor, but I do not see a strong case for doing either, so I
went with a simple implementation.
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #1161
The function zfs_nicenum that converts number to human-readable output
uses a index to a string of letters. This patch limits the index to
the length of the string.
Signed-off-by: Christer Ekholm <che@chrekh.se>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#3122
In order to accelerate zfs receive operations in the face of many
property-containing snapshots, commit 0574855 changed the header nvlist
("fss") of a send stream to exclude snapshots which aren't part of the
stream. This, however, would cause zfs receive -F to erroneously remove
snapshots; it would remove any snapshot which wasn't listed in the header
nvlist.
This patch restores the full list of snapshots in fss[<id>[snaps]] but
still suppresses the properties of non-sent snapshots and also removes a
consistency check in which an error is raised if a listed snapshot does
not have any properties in fss[<id>[snapprops]].
The 0574855 commit also introduced a bug in which zfs send -p of a
complete stream (zfs send -p pool/fs@snap) would exclude the snapshot
properties in fss[<id>[snapprops]]. This patch detects the last snapshot
in a series when no "from" snapshot has been specified and includes its
properties.
Signed-off-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2907
If spl_hostid is set via module parameter, it's likely different from
gethostid(). Therefore, the userspace tool should read it first before
falling back to gethostid().
Signed-off-by: Chunwei Chen <tuxoko@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#3034
When importing pools with zpool import -aN there is inconsistent
behavior between '-d /dev/disk/by-id' (or another path) and
'-c /etc/zfs/zpool.cache'.
The difference in behavior is caused by zpool_find_import_cached()
returning an empty nvlist_t when there are no pools to import but
zpool_find_import_impl() returns NULL for the same situation. The
behavior of zpool_find_import_cached() is arguably more correct
because it allows returning NULL to be used for an error case and
not an empty set.
This change resolves the issue by updating get_configs() such that
it returns an empty set instead of NULL when no config is found.
The updated behavior will now always return 0 for this case.
$ zpool import -aN; echo $?
no pools available to import
0
$ zpool import -aN -d /var/tmp/; echo $?
no pools available to import
0
$ zpool import -aN -c /etc/zfs/zpool.cache; echo $?
no pools available to import
0
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2080
... as opposed to sending properties of all snapshots of the relevant
filesystem. The previous behavior results in properties being set on
all snapshots on the receiving side, which is quite slow.
Behavior of zfs send -R is not changed.
References:
http://thread.gmane.org/gmane.comp.file-systems.openzfs.devel/346
Ported-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #2729
Issue #2210
FreeBSD PR kern/172259: Fixes zfs receive errors caused by snapshot
replication being processed in a random order instead of creation
order.
Eliminates needless filesystem renames caused by removed parent
snapshots which subsequently causes many more errors.
PR: kern/172259
Submitted by: Steven Hartland
Reviewed by: pjd (mentor)
Approved by: pjd (mentor)
MFC after: 2 weeks
References:
https://github.com/freebsd/freebsd/commit/4995789
Porting notes:
Minor whitespace fixes were made to conform with style requirements:
lib/libzfs/libzfs_sendrecv.c: 2269: indent by spaces instead of tabs
lib/libzfs/libzfs_sendrecv.c: 2270: indent by spaces instead of tabs
Ported-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #2729
Creating virtual machines that have their rootfs on ZFS on hosts that
have their rootfs on ZFS causes SPA namespace collisions when the
standard name rpool is used. The solution is either to give each guest
pool a name unique to the host, which is not always desireable, or boot
a VM environment containing an ISO image to install it, which is
cumbersome.
26b42f3f9d introduced `zpool import -t
...` to simplify situations where a host must access a guest's pool when
there is a SPA namespace conflict. We build upon that to introduce
`zpool import -t tname ...`. That allows us to create a pool whose
in-core name is tname, but whose on-disk name is the normal name
specified.
This simplifies the creation of machine images that use a rootfs on ZFS.
That benefits not only real world deployments, but also ZFSOnLinux
development by decreasing the time needed to perform rootfs on ZFS
experiments.
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #2417
5116 zpool history -i goes into infinite loop
Reviewed by: Christopher Siden <christopher.siden@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Richard Elling <richard.elling@gmail.com>
Reviewed by: Boris Protopopov <boris.protopopov@me.com>
Approved by: Dan McDonald <danmcd@omniti.com>
References:
https://www.illumos.org/issues/5116https://github.com/illumos/illumos-gate/commit/3339867
Ported by: Turbo Fredriksson <turbo@bayour.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2715
The 'zpool list -v' command displays lots of info but excludes the
capacity of each disk. This should be added.
5147 zpool list -v should show individual disk capacity
Reviewed by: Adam Leventhal <adam.leventhal@delphix.com>
Reviewed by: Christopher Siden <christopher.siden@delphix.com>
Reviewed by: Matthew Ahrens <matthew.ahrens@delphix.com>
Reviewed by: Richard Elling <richard.elling@gmail.com>
Approved by: Dan McDonald <danmcd@omniti.com>
References:
https://www.illumos.org/issues/5147https://github.com/illumos/illumos-gate/commit/7a09f97
Ported by: Turbo Fredriksson <turbo@bayour.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2688
When com.delphix:spacemap_histogram is disabled, the value of
fragmentation was printing as 18446744073709551615 (UINT64_MAX),
when it should print as '-'.
The issue was caused by a small mistake during the merge of
"4980 metaslabs should have a fragmentation metric."
upstream: https://github.com/illumos/illumos-gate/commit/2e4c998
ZoL: https://github.com/zfsonlinux/zfs/commit/f3a7f66
The problem is in zpool_get_prop_literal, where the handling of the
pool property ZPOOL_PROP_FRAGMENTATION was added to wrong the
section. In particular, ZPOOL_PROP_FRAGMENTATION should not be in
the section where zpool_get_state(zhp) == POOL_STATE_UNAVAIL, but
lower down after it's already been determined that the pool is in
fact available, which is where upstream illumos correctly has had
it.
Thanks to lundman for helping to track down this bug.
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Signed-off-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2664
Providing a pkg-config file makes is easy for 3rd party applications
to link against the libzfs libraries. It also allows the libzfs
developers to modify the list of required libraries and cflags
without breaking existing applications.
The following example illustrates how pkg-config can be used:
cc `pkg-config --cflags --libs libzfs` -o myapp myapp.c
/*
* myapp.c
*/
void main()
{
libzfs_handle_t *hdl;
hdl = libzfs_init();
if (hdl)
libzfs_fini(hdl);
}
Signed-off-by: Turbo Fredriksson <turbo@bayour.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes: #585
4976 zfs should only avoid writing to a failing non-redundant top-level vdev
4978 ztest fails in get_metaslab_refcount()
4979 extend free space histogram to device and pool
4980 metaslabs should have a fragmentation metric
4981 remove fragmented ops vector from block allocator
4982 space_map object should proactively upgrade when feature is enabled
4983 need to collect metaslab information via mdb
4984 device selection should use fragmentation metric
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Adam Leventhal <adam.leventhal@delphix.com>
Reviewed by: Christopher Siden <christopher.siden@delphix.com>
Approved by: Garrett D'Amore <garrett@damore.org>
References:
https://www.illumos.org/issues/4976https://www.illumos.org/issues/4978https://www.illumos.org/issues/4979https://www.illumos.org/issues/4980https://www.illumos.org/issues/4981https://www.illumos.org/issues/4982https://www.illumos.org/issues/4983https://www.illumos.org/issues/4984https://github.com/illumos/illumos-gate/commit/2e4c998
Notes:
The "zdb -M" option has been re-tasked to display the new metaslab
fragmentation metric and the new "zdb -I" option is used to control
the maximum number of in-flight I/Os.
The new fragmentation metric is derived from the space map histogram
which has been rolled up to the vdev and pool level and is presented
to the user via "zpool list".
Add a number of module parameters related to the new metaslab weighting
logic.
Ported by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2595
4914 zfs on-disk bookmark structure should be named *_phys_t
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Christopher Siden <christopher.siden@delphix.com>
Reviewed by: Richard Lowe <richlowe@richlowe.net>
Reviewed by: Saso Kiselkov <skiselkov.ml@gmail.com>
Approved by: Robert Mustacchi <rm@joyent.com>
References:
https://www.illumos.org/issues/4914https://github.com/illumos/illumos-gate/commit/7802d7b
Porting notes:
There were a number of zfsonlinux-specific uses of zbookmark_t which
needed to be updated. This should reduce the likelihood of further
problems like issue #2094 from occurring.
Ported by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2558
4390 i/o errors when deleting filesystem/zvol can lead to space map corruption
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Christopher Siden <christopher.siden@delphix.com>
Reviewed by: Adam Leventhal <ahl@delphix.com>
Reviewed by: Dan McDonald <danmcd@omniti.com>
Reviewed by: Saso Kiselkov <saso.kiselkov@nexenta.com>
Approved by: Dan McDonald <danmcd@omniti.com>
References:
https://www.illumos.org/issues/4390https://github.com/illumos/illumos-gate/commit/7fd05ac
Porting notes:
Previous stack-reduction efforts in traverse_visitb() caused a fair
number of un-mergable pieces of code. This patch should reduce its
stack footprint a bit more.
The new local bptree_entry_phys_t in bptree_add() is dynamically-allocated
using kmem_zalloc() for the purpose of stack reduction.
The new global zfs_free_leak_on_eio has been defined as an integer
rather than a boolean_t as was the case with the related zfs_recover
global. Also, zfs_free_leak_on_eio's definition has been inserted into
zfs_debug.c for consistency with the existing definition of zfs_recover.
Illumos placed it in spa_misc.c.
Ported by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2545
4757 ZFS embedded-data block pointers ("zero block compression")
4913 zfs release should not be subject to space checks
Reviewed by: Adam Leventhal <ahl@delphix.com>
Reviewed by: Max Grossman <max.grossman@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Christopher Siden <christopher.siden@delphix.com>
Reviewed by: Dan McDonald <danmcd@omniti.com>
Approved by: Dan McDonald <danmcd@omniti.com>
References:
https://www.illumos.org/issues/4757https://www.illumos.org/issues/4913https://github.com/illumos/illumos-gate/commit/5d7b4d4
Porting notes:
For compatibility with the fastpath code the zio_done() function
needed to be updated. Because embedded-data block pointers do
not require DVAs to be allocated the associated vdevs will not
be marked and therefore should not be unmarked.
Ported by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2544
4171 clean up spa_feature_*() interfaces
4172 implement extensible_dataset feature for use by other zpool features
Reviewed by: Max Grossman <max.grossman@delphix.com>
Reviewed by: Christopher Siden <christopher.siden@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Jerry Jelinek <jerry.jelinek@joyent.com>
Approved by: Garrett D'Amore <garrett@damore.org>a
References:
https://www.illumos.org/issues/4171https://www.illumos.org/issues/4172https://github.com/illumos/illumos-gate/commit/2acef22
Ported-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2528
Updates 962d524212.
The referenced fix to get_numeric_property() caused numeric property
lookups to consider the type of the parent (head) dataset when checking
validity but there are some cases in the caller expects to see the
property's default value even when the lookup is invalid.
One case in which this is true is change_one() which is part of the
renaming infrastructure. It may look up "zoned" on a snapshot of a volume
which is not valid but it expects to see the default value of false.
There may be other, yet unidentified cases in which zfs_prop_get_int()
is used on technically invalid properties but which expect the property's
default value to be returned.
Signed-off-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Turbo Fredriksson <turbo@bayour.com>
Closes#2320
When adding or replacing a vdev with a different sector size the
error message should be more useful. In addition to describing
the problem provide a hint that the '-o ashift' option can be
used to override the optimal default value.
Since using a non-optimal value may incur a significant performance
penalty we should issue this error. But there a numerous reasons
why a administrator may wish to do this anyway.
Signed-off-by: Niklas Edmundsson <ZNikke@github>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2421
Clang's static analyzer reported a memory leak in zpool_clear_label().
Upon review, it turns out to be right. This should be a very short lived
leak because no daemons use this functionality, but that does not
preclude the possibility of third party daemons that do use it. Lets fix
it to be a good Samaritan.
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Ned Bass <bass6@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #2330
When fetching property values of snapshots, a check against the head
dataset type must be performed. Previously, this additional check was
performed only when fetching "version", "normalize", "utf8only" or "case".
This caused the ZPL properties "acltype", "exec", "devices", "nbmand",
"setuid" and "xattr" to be erroneously displayed with meaningless values
for snapshots of volumes. It also did not allow for the display of
"volsize" of a snapshot of a volume.
This patch adds the headcheck flag paramater to zfs_prop_valid_for_type()
and zprop_valid_for_type() to indicate the check is being done
against a head dataset's type in order that properties valid only for
snapshots are handled correctly. This allows the the head check in
get_numeric_property() to be performed when fetching a property for
a snapshot.
Signed-off-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2265
zfs_is_mountable() fills in the mountpoint buffer, so, as in
upstream, it needs to have been called before the mountpoint
buffer can be used in error messages.
In particular,
return (zfs_error_fmt(hdl, EZFS_MOUNTFAILED,
dgettext(TEXT_DOMAIN, "cannot mount '%s'"),
mountpoint));
should not come before the call to zfs_is_mountable().
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: ilovezfs <ilovezfs@icloud.com>
Closes#2284
Neither atime nor relatime should be considered to be "temporary mount
point properties". Their semantics are enforced completely within ZFS
and also they're (correctly) not documented as being temporary mount
point properties.
Signed-off-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2257
This is a continuation of fb5c53ea65:
When /etc/mtab is updated on Linux it's done atomically with
rename(2). A new mtab is written, the existing mtab is unlinked,
and the new mtab is renamed to /etc/mtab. This means that we
must close the old file and open the new file to get the updated
contents. Using rewind(3) will just move the file pointer back
to the start of the file, freopen(3) will close and open the file.
In this commit, a few more rewind(3) calls were replaced with freopen(3)
to allow updated mtab entries to be picked up immediately.
Signed-off-by: John M. Layman <jml@frijid.net>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2215
Issue #1611
Several of the zfs utilities allow you to pass a vdev's guid rather
than the device name. However, the utilities are not consistent in
how they parse that guid. For example, 'zinject' expects the guid
to be passed as a hex value while 'zpool replace' wants it as a
decimal. The user is forced to just know what format to use.
This patch improve things by making the parsing more tolerant.
When strtol(3) is called using 0 for the base, rather than say
10 or 16, it will then accept hex, decimal, or octal input based
on the prefix. From the man page.
If base is zero or 16, the string may then include a "0x"
prefix, and the number will be read in base 16; otherwise,
a zero base is taken as 10 (decimal) unless the next character
is '0', in which case it is taken as 8 (octal).
NOTE: There may be additional conversions not caught be this patch.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chris Dunlap <cdunlap@llnl.gov>
Issue #2
zpool_events_next() can be called in blocking mode by specifying a
non-zero value for the "block" parameter. However, the design of
the ZFS Event Daemon (zed) requires additional functionality from
zpool_events_next(). Instead of adding additional arguments to the
function, it makes more sense to use flags that can be bitwise-or'd
together.
This commit replaces the zpool_events_next() int "block" parameter with
an unsigned bitwise "flags" parameter. It also defines ZEVENT_NONE
to specify the default behavior. Since non-blocking mode can be
specified with the existing ZEVENT_NONBLOCK flag, the default behavior
becomes blocking mode. This, in effect, inverts the previous use
of the "block" parameter. Existing callers of zpool_events_next()
have been modified to check for the ZEVENT_NONBLOCK flag.
Signed-off-by: Chris Dunlap <cdunlap@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #2
Due to the very poorly chosen argument name 'cleanup_fd' it was
completely unclear that this file descriptor is used to track the
current cursor location. When the file descriptor is created by
opening ZFS_DEV a private cursor is created in the kernel for the
returned file descriptor. Subsequent calls to zpool_events_next()
and zpool_events_seek() then require the file descriptor as an
argument to reposition the cursor. When the file descriptor is
closed the kernel state tracking the cursor is destroyed.
This patch contains no functional change, it just changes a
few variable names and clarifies the documentation.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chris Dunlap <cdunlap@llnl.gov>
Issue #2
The ZFS_IOC_EVENTS_SEEK ioctl was added to allow user space callers
to seek around the zevent file descriptor by EID. When a specific
EID is passed and it exists the cursor will be positioned there.
If the EID is no longer cached by the kernel ENOENT is returned.
The caller may also pass ZEVENT_SEEK_START or ZEVENT_SEEK_END to seek
to those respective locations.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chris Dunlap <cdunlap@llnl.gov>
Issue #2
Changing properties with "zfs inherit" should cause the datasets
to be remounted. This ensures that the modified property values
will be propagated in to the filesystem namespace where they can
be enforced. This change is modeled after an identical fix made
to zfs_prop_set().
Signed-off-by: Gunnar Beutner <gunnar@beutner.name>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2201
From time to time it may be necessary to inform the pool administrator
about an errata which impacts their pool. These errata will by shown
to the administrator through the 'zpool status' and 'zpool import'
output as appropriate. The errata must clearly describe the issue
detected, how the pool is impacted, and what action should be taken
to resolve the situation. Additional information for each errata will
be provided at http://zfsonlinux.org/msg/ZFS-8000-ER.
To accomplish the above this patch adds the required infrastructure to
allow the kernel modules to notify the utilities that an errata has
been detected. This is done through the ZPOOL_CONFIG_ERRATA uint64_t
which has been added to the pool configuration nvlist.
To add a new errata the following changes must be made:
* A new errata identifier must be assigned by adding a new enum value
to the zpool_errata_t type. New enums must be added to the end to
preserve the existing ordering.
* Code must be added to detect the issue. This does not strictly
need to be done at pool import time but doing so will make the
errata visible in 'zpool import' as well as 'zpool status'. Once
detected the spa->spa_errata member should be set to the new enum.
* If possible code should be added to clear the spa->spa_errata member
once the errata has been resolved.
* The show_import() and status_callback() functions must be updated
to include an informational message describing the errata. This
should include an action message describing what an administrator
should do to address the errata.
* The documentation at http://zfsonlinux.org/msg/ZFS-8000-ER must be
updated to describe the errata. This space can be used to provide
as much additional information as needed to fully describe the errata.
A link to this documentation will be automatically generated in the
output of 'zpool import' and 'zpool status'.
Original-idea-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Richard Yao <ryao@gentoo.or
Issue #2094
Add the "relatime" property. When set to "on", a file's atime will only
be updated if the existing atime at least a day old or if the existing
ctime or mtime has been updated since the last access. This behavior
is compatible with the Linux "relatime" mount option.
Signed-off-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2064Closes#1917
Under Linux its possible to mount the same filesystem multiple
times in the namespace. This can be done either with bind mounts
or simply with multiple mount points. Unfortunately, the mnttab
cache code is implemented using an AVL tree which does not support
duplicate entries. To avoid this issue this patch updates the
code to check for a duplicate entry before adding a new one.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Michael Martin <mgmartin.mgm@gmail.com>
Closes#2041
The vast majority of these changes are in Linux specific code.
They are the result of not having an automated style checker to
validate the code when it was originally written. Others were
caused when the common code was slightly adjusted for Linux.
This patch contains no functional changes. It only refreshes
the code to conform to style guide.
Everyone submitting patches for inclusion upstream should now
run 'make checkstyle' and resolve any warning prior to opening
a pull request. The automated builders have been updated to
fail a build if when 'make checkstyle' detects an issue.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1821
Early versions of ZFS coordinated the creation and destruction
of device minors from userspace. This was inherently racy and
in late 2009 these ioctl()s were removed leaving everything up
to the kernel. This significantly simplified the code.
However, we never picked up these changes in ZoL since we'd
already significantly adjusted this code for Linux. This patch
aims to rectify that by finally removing ZFC_IOC_*_MINOR ioctl()s
and moving all the functionality down in to the kernel. Since
this cleanup will change the kernel/user ABI it's being done
in the same tag as the previous libzfs_core ABI changes. This
will minimize, but not eliminate, the disruption to end users.
Once merged ZoL, Illumos, and FreeBSD will basically be back
in sync in regards to handling ZVOLs in the common code. While
each platform must have its own custom zvol.c implemenation the
interfaces provided are consistent.
NOTES:
1) This patch introduces one subtle change in behavior which
could not be easily avoided. Prior to this change callers
of 'zfs create -V ...' were guaranteed that upon exit the
/dev/zvol/ block device link would be created or an error
returned. That's no longer the case. The utilities will no
longer block waiting for the symlink to be created. Callers
are now responsible for blocking, this is why a 'udev_wait'
call was added to the 'label' function in scripts/common.sh.
2) The read-only behavior of a ZVOL now solely depends on if
the ZVOL_RDONLY bit is set in zv->zv_flags. The redundant
policy setting in the gendisk structure was removed. This
both simplifies the code and allows us to safely leverage
set_disk_ro() to issue a KOBJ_CHANGE uevent. See the
comment in the code for futher details on this.
3) Because __zvol_create_minor() and zvol_alloc() may now be
called in a sync task they must use KM_PUSHPAGE.
References:
illumos/illumos-gate@681d9761e8
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ned Bass <bass6@llnl.gov>
Signed-off-by: Tim Chase <tim@chase2k.com>
Closes#1969
Under Linux this restriction does not apply because we have access
to all the required devices.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1631
In the current snapshot automount implementation, it is possible for
multiple mounts to attempted concurrently. Only one of the mounts will
succeed and the other will fail. The failed mounts will cause an EREMOTE
to be propagated back to the application.
This commit works around the problem by adding a new exit status,
MOUNT_BUSY to the mount.zfs program which is used when the underlying
mount(2) call returns EBUSY. The zfs code detects this condition and
treats it as if the mount had succeeded.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1819
3996 want a libzfs_core API to rollback to latest snapshot
Reviewed by: Christopher Siden <christopher.siden@delphix.com>
Reviewed by: Adam Leventhal <ahl@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Andy Stormont <andyjstormont@gmail.com>
Approved by: Richard Lowe <richlowe@richlowe.net>
References:
https://www.illumos.org/issues/3996illumos/illumos-gate@a7027df17f
Ported-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #1775
3909 "zfs send -D" does not work
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Approved by: Christopher Siden <christopher.siden@delphix.com>
References:
https://www.illumos.org/issues/3909illumos/illumos-gate@36f7455d36
Ported-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #1775
3894 zfs should not allow snapshot of inconsistent dataset
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Approved by: Gordon Ross <gwr@nexenta.com>
References:
https://www.illumos.org/issues/3894illumos/illumos-gate@ca48f36f20
Ported-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #1775
3829 fix for 3740 changed behavior of zfs destroy/hold/release ioctl
Reviewed by: Matt Amdur <matt.amdur@delphix.com>
Reviewed by: Christopher Siden <christopher.siden@delphix.com>
Approved by: Richard Lowe <richlowe@richlowe.net>
References:
https://www.illumos.org/issues/3829illumos/illumos-gate@bb6e70758d
Ported-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #1775
3818 zpool status -x should report pools with removed l2arc devices
Reviewed by: Saso Kiselkov <skiselkov.ml@gmail.com>
Reviewed by: George Wilson <gwilson@zfsmail.com>
Approved by: Christopher Siden <christopher.siden@delphix.com>
References:
https://www.illumos.org/issues/3818illumos/illumos-gate@7f2416ef64
Ported-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #1775
3740 Poor ZFS send / receive performance due to snapshot
hold / release processing
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Approved by: Christopher Siden <christopher.siden@delphix.com>
References:
https://www.illumos.org/issues/3740illumos/illumos-gate@a7a845e4bf
Ported-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #1775
Porting notes:
1. 13fe019870 introduced a merge conflict
in dsl_dataset_user_release_tmp where some variables were moved
outside of the preprocessor directive.
2. dea9dfefdd747534b3846845629d2200f0616dad made the previous merge
conflict worse by switching KM_SLEEP to KM_PUSHPAGE. This is notable
because this commit refactors the code, adding a new KM_SLEEP
allocation. It is not clear to me whether this should be converted
to KM_PUSHPAGE.
3. We had a merge conflict in libzfs_sendrecv.c because of copyright
notices.
4. Several small C99 compatibility fixed were made.
3745 zpool create should treat -O mountpoint and -m the same
3811 zpool create -o altroot=/xyz -O mountpoint=/mnt ignores
the mountpoint option
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Approved by: Christopher Siden <christopher.siden@delphix.com>
References:
https://www.illumos.org/issues/3745https://www.illumos.org/issues/3811illumos/illumos-gate@8b71377531
Ported-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #1775
