As of the 5.17 kernel the GENHD_FL_EXT_DEVT flag has been removed
and the GENHD_FL_NO_PART_SCAN flag renamed GENHD_FL_NO_PART. Update
zvol_alloc() to set GENHD_FL_NO_PART for the newer kernels which
is sufficient. The behavior for prior kernels remains unchanged.
1ebe2e5f ("block: remove GENHD_FL_EXT_DEVT")
46e7eac6 ("block: rename GENHD_FL_NO_PART_SCAN to GENHD_FL_NO_PART")
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13294Closes#13297
FreeBSD's memory management system uses its own error numbers and gets
confused when these VOPs return EIO.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reported-by: Peter Holm <pho@FreeBSD.org>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#13311
For legacy reasons, a couple of VOPs have to return error numbers that
don't come from the usual errno namespace. To handle the cases where
ZFS_ENTER or ZFS_VERIFY_ZP fail, we need to be able to override the
default error return value of EIO. Extend the macros to permit this.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#13311
->readpages was removed and replaced by ->readahead. Define
zpl_readahead for kernels that don't have ->readpages.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Riccardo Schirone <rschirone91@gmail.com>
Closes#13278
NDF_ONLY_PNBUF has been removed from FreeBSD in favor of NDFREE_PNBUF.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#13277
Bypass check of ZFS aces if the ACL is trivial. When an ACL is
trivial its permissions are represented by the mode without any
loss of information. In this case, it is safe to convert the
access request into equivalent mode and then pass desired mask
and inode to generic_permission(). This has the added benefit
of also checking whether entries in a POSIX ACL on the file grant
the desired access.
This commit also skips the ACL check on looking up the xattr dir
since such restrictions don't exist in Linux kernel and it makes
xattr lookup behavior inconsistent between SA and file-based
xattrs. We also don't want to perform a POSIX ACL check while
looking up the POSIX ACL if for some reason it is located in
the xattr dir rather than an SA.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Andrew Walker <awalker@ixsystems.com>
Closes#13237
The argument type of rw_destroy is (krwlock_t *) while currently
krwlock_t is passed in zfs_ctldir.c. This error is hidden because
rw_destroy is defined as ((void) 0) in linux. But anyway, this
mismatch should be fixed.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ping Huang <huangping@smartx.com>
Closes#13272
When HAVE_BLKDEV_GET_ERESTARTSYS is defined, compiler will complain
"defined but not used" warning for zvol_open_timeout_ms.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ping Huang <huangping@smartx.com>
Closes#13270
blkdev.h includes genhd.h since dawn of upstream git, so this is
globally safe
Upstream-commit: 322cbb50de711814c42fb088f6d31901502c711a ("block:
remove genhd.h")
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13251
bio_alloc(gfp_t gfp_mask, unsigned short nr_iovecs)
became
bio_alloc(struct block_device *bdev, unsigned short nr_vecs,
unsigned int opf, gfp_t gfp_mask)
passing NULL/0 continues previous behaviour
Upstream-commit: 07888c665b405b1cd3577ddebfeb74f4717a84c4 ("block:
pass a block_device and opf to bio_alloc")
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13251
Parts of the Linux kernel build system struggle with _Noreturn. This
results in the following warnings when building on RHEL 8.5, and likely
other environments. Switch to using the __attribute__((noreturn)).
warning: objtool: dbuf_free_range()+0x2b8:
return with modified stack frame
warning: objtool: dbuf_free_range()+0x0:
stack state mismatch: cfa1=7+40 cfa2=7+8
...
WARNING: EXPORT symbol "arc_buf_size" [zfs.ko] version generation
failed, symbol will not be versioned.
WARNING: EXPORT symbol "spa_open" [zfs.ko] version generation
failed, symbol will not be versioned.
...
Additionally, __thread_exit() has been renamed spl_thread_exit() and
made a static inline function. This was needed because the kernel
will generate a warning for symbols which are __attribute__((noreturn))
and then exported with EXPORT_SYMBOL.
While we could continue to use _Noreturn in user space I've also
switched it to __attribute__((noreturn)) purely for consistency
throughout the code base.
Reviewed-by: Ryan Moeller <freqlabs@FreeBSD.org>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13238
This PR changes ZFS ACL checks to evaluate
fsuid / fsgid rather than euid / egid to avoid
accidentally granting elevated permissions to
NFS clients.
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Andrew Walker <awalker@ixsystems.com>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#13221
At shutdown time, we drain all of the zevents and set the
ZEVENT_SHUTDOWN flag. On FreeBSD, we may end up calling
zfs_zevent_destroy() after the zevent_lock has been destroyed while
the sysevent thread is winding down; we observe ESHUTDOWN, then back
out.
Events have already been drained, so just inline the kmem_free call in
sysevent_worker() to avoid the race, and document the assumption that
zfs_zevent_destroy doesn't do anything else useful at that point.
This fixes a panic that can occur at module unload time.
Reviewed-by: Ryan Moeller <freqlabs@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Kyle Evans <kevans@FreeBSD.org>
Closes#13220
bcopy() has a confusing argument order and is actually a move, not a
copy; they're all deprecated since POSIX.1-2001 and removed in -2008,
and we shim them out to mem*() on Linux anyway
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12996
On some architectures ZERO_PAGE is unavailable because it references
a GPL exported symbol of empty_zero_page. Originally e08b993 removed
the call to PAGE_ZERO(0) for assignment to the abd_zero_page. However,
a simple check can be done to avoid a kernel allocation and free for
the abd_zero_page if ZERO_PAGE is available.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Brian Atkinson <batkinson@lanl.gov>
Closes#13199
ZFS allows to update and retrieve additional file level attributes for
FreeBSD. This commit allows additional file level attributes to be
updated and retrieved for Linux. These include the flags stored in the
upper half of z_pflags only.
Two new IOCTLs have been added for this purpose. ZFS_IOC_GETDOSFLAGS
can be used to retrieve the attributes, while ZFS_IOC_SETDOSFLAGS can
be used to update the attributes.
Attributes that are allowed to be updated include ZFS_IMMUTABLE,
ZFS_APPENDONLY, ZFS_NOUNLINK, ZFS_ARCHIVE, ZFS_NODUMP, ZFS_SYSTEM,
ZFS_HIDDEN, ZFS_READONLY, ZFS_REPARSE, ZFS_OFFLINE and ZFS_SPARSE.
Flags can be or'd together while calling ZFS_IOC_SETDOSFLAGS.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Umer Saleem <usaleem@ixsystems.com>
Closes#13118
As such, there are no specific synchronous semantics defined for
the xattrs. But for xattr=on, it does log to ZIL and zil_commit() is
done, if sync=always is set on dataset. This provides sync semantics
for xattr=on with sync=always set on dataset.
For the xattr=sa implementation, it doesn't log to ZIL, so, even with
sync=always, xattrs are not guaranteed to be synced before xattr call
returns to caller. So, xattr can be lost if system crash happens, before
txg carrying xattr transaction is synced.
This change adds xattr=sa logging to ZIL on xattr create/remove/update
and xattrs are synced to ZIL (zil_commit() done) for sync=always.
This makes xattr=sa behavior similar to xattr=on.
Implementation notes:
The actual logging is fairly straight-forward and does not warrant
additional explanation.
However, it has been 14 years since we last added new TX types
to the ZIL [1], hence this is the first time we do it after the
introduction of zpool features. Therefore, here is an overview of the
feature activation and deactivation workflow:
1. The feature must be enabled. Otherwise, we don't log the new
record type. This ensures compatibility with older software.
2. The feature is activated per-dataset, since the ZIL is per-dataset.
3. If the feature is enabled and dataset is not for zvol, any append to
the ZIL chain will activate the feature for the dataset. Likewise
for starting a new ZIL chain.
4. A dataset that doesn't have a ZIL chain has the feature deactivated.
We ensure (3) by activating on the first zil_commit() after the feature
was enabled. Since activating the features requires waiting for txg
sync, the first zil_commit() after enabling the feature will be slower
than usual. The downside is that this is really a conservative
approximation: even if we never append a 'TX_SETSAXATTR' to the ZIL
chain, we pay the penalty for feature activation. The upside is that the
user is in control of when we pay the penalty, i.e., upon enabling the
feature.
We ensure (4) by hooking into zil_sync(), where ZIL destroy actually
happens.
One more piece on feature activation, since it's spread across
multiple functions:
zil_commit()
zil_process_commit_list()
if lwb == NULL // first zil_commit since zil_open
zil_create()
if no log block pointer in ZIL header:
if feature enabled and not active:
// CASE 1
enable, COALESCE txg wait with dmu_tx that allocated the
log block
else // log block was allocated earlier than this zil_open
if feature enabled and not active:
// CASE 2
enable, EXPLICIT txg wait
else // already have an in-DRAM LWB
if feature enabled and not active:
// this happens when we enable the feature after zil_create
// CASE 3
enable, EXPLICIT txg wait
[1] da6c28aaf6
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Christian Schwarz <christian.schwarz@nutanix.com>
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Reviewed-by: Ryan Moeller <freqlabs@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jitendra Patidar <jitendra.patidar@nutanix.com>
Closes#8768Closes#9078
The default behavior where the serious ZFS errors cause FS thread to
stuck is very bad for some production scenario.
In some production scenarios (Linux), it is recommended to make real
kernel PANIC, where system can be rebooted by watchdog or kernel itself.
This patch enables coherent handling of spl_panic_halt parameter.
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Authored-by: Wojciech Nizinski <w.nizinski@grinn-global.com>
Signed-off-by: szubersk <szuberskidamian@gmail.com>
Closes#12120Closes#13109
ZFS on Linux originally implemented xattr namespaces in a way that is
incompatible with other operating systems. On illumos, xattrs do not
have namespaces. Every xattr name is visible. FreeBSD has two
universally defined namespaces: EXTATTR_NAMESPACE_USER and
EXTATTR_NAMESPACE_SYSTEM. The system namespace is used for protected
FreeBSD-specific attributes such as MAC labels and pnfs state. These
attributes have the namespace string "freebsd:system:" prefixed to the
name in the encoding scheme used by ZFS. The user namespace is used
for general purpose user attributes and obeys normal access control
mechanisms. These attributes have no namespace string prefixed, so
xattrs written on illumos are accessible in the user namespace on
FreeBSD, and xattrs written to the user namespace on FreeBSD are
accessible by the same name on illumos.
Linux has several xattr namespaces. On Linux, ZFS encodes the
namespace in the xattr name for every namespace, including the user
namespace. As a consequence, an xattr in the user namespace with the
name "foo" is stored by ZFS with the name "user.foo" and therefore
appears on FreeBSD and illumos to have the name "user.foo" rather than
"foo". Conversely, none of the xattrs written on FreeBSD or illumos
are accessible on Linux unless the name happens to be prefixed with one
of the Linux xattr namespaces, in which case the namespace is stripped
from the name. This makes xattrs entirely incompatible between Linux
and other platforms.
We want to make the encoding of user namespace xattrs compatible across
platforms. A critical requirement of this compatibility is for xattrs
from existing pools from FreeBSD and illumos to be accessible by the
same names in the user namespace on Linux. It is also necessary that
existing pools with xattrs written by Linux retain access to those
xattrs by the same names on Linux. Making user namespace xattrs from
Linux accessible by the correct names on other platforms is important.
The handling of other namespaces is not required to be consistent.
Add a fallback mechanism for listing and getting xattrs to treat xattrs
as being in the user namespace if they do not match a known prefix.
Do not allow setting or getting xattrs with a name that is prefixed
with one of the namespace names used by ZFS on supported platforms.
Allow choosing between legacy illumos and FreeBSD compatibility and
legacy Linux compatibility with a new tunable. This facilitates
replication and migration of pools between hosts with different
compatibility needs.
The tunable controls whether or not to prefix the namespace to the
name. If the xattr is already present with the alternate prefix,
remove it so only the new version persists. By default the platform's
existing convention is used.
Reviewed-by: Christian Schwarz <christian.schwarz@nutanix.com>
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11919
It's the only one actually used
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12901
Add hooks for when spa is created, exported, activated and
deactivated. Used by macOS to attach iokit, and lock
kext as busy (to stop unloads).
Userland, Linux, and, FreeBSD have empty stubs.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Closes#12801
Unfortunately macOS has obj-C keyword "fallthrough" in the OS headers.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Damian Szuberski <szuberskidamian@gmail.com>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Closes#13097
This allows reads/writes caused by accesses to mmap files to be
accounted correctly in the per-dataset kstats for both Linux and
FreeBSD.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <freqlabs@FreeBSD.org>
Signed-off-by: Matthias Blankertz <matthias@blankertz.org>
Closes#12994Closes#13044
To follow a change in illumos taskq
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Closes#12802
There's no need to make the platform ops dynamic dispatch.
This change replaces the dynamic dispatch with static calls to the
platform-specific functions.
To avoid name collisions, prefix all platform-specific functions
with `zvol_os_`.
I actually find `zvol_..._os` slightly nicer to read in the calling
code, but having it as a prefix is useful.
Advantage:
- easier jump-to-definition / grepping
- potential benefits to static analysis
- better legibility
Future work: also prefix remaining `static` functions in zvol_os.c.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Christian Schwarz <christian.schwarz@nutanix.com>
Closes#12965
69 CSTYLED BEGINs remain, appx. 30 of which can be removed if cstyle(1)
had a useful policy regarding
CALL(ARG1,
ARG2,
ARG3);
above 2 lines. As it stands, it spits out *both*
sysctl_os.c: 385: continuation line should be indented by 4 spaces
sysctl_os.c: 385: indent by spaces instead of tabs
which is very cool
Another >10 could be fixed by removing "ulong" &al. handling.
I don't foresee anyone actually using it intentionally
(does it even exist in modern headers? why did it in the first place?).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12993
First open locking changes were correctly applied to zvol_geom_open but
incorrectly applied to zvol_cdev_open, causing spa_namespace_lock to be
held indefinitely.
Make the first open locking in zvol_cdev_open match zvol_geom_open.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#13016
When using the two argument version of submit_bio() in kernel's prior
to 4.8 the first argument should be specified. It's used by block
dump to report the bio direction.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Finix Yan <yancw@info2soft.com>
Closes#13006
Linux 5.17 sees a rename from complete_and_exit()
to kthread complete_and_exit()
Upstream commit cead18552660702a4a46f58e65188fe5f36e9dfe
("exit: Rename complete_and_exit to kthread_complete_and_exit")
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12989
For us, I think it's always just FALLOC_FL_PUNCH_HOLE with a fake
mustache on.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Coleman Kane <ckane@colemankane.org>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12975
add_disk went from void to must-check int return.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Coleman Kane <ckane@colemankane.org>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12975
Raw receiving a snapshot back to the originating dataset is currently
impossible because of user accounting being present in the originating
dataset.
One solution would be resetting user accounting when raw receiving on
the receiving dataset. However, to recalculate it we would have to dirty
all dnodes, which may not be preferable on big datasets.
Instead, we rely on the os_phys flag
OBJSET_FLAG_USERACCOUNTING_COMPLETE to indicate that user accounting is
incomplete when raw receiving. Thus, on the next mount of the receiving
dataset the local mac protecting user accounting is zeroed out.
The flag is then cleared when user accounting of the raw received
snapshot is calculated.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#12981Closes#10523Closes#11221Closes#11294Closes#12594
Issue #11300
Evaluated every variable that lives in .data (and globals in .rodata)
in the kernel modules, and constified/eliminated/localised them
appropriately. This means that all read-only data is now actually
read-only data, and, if possible, at file scope. A lot of previously-
global-symbols became inlinable (and inlined!) constants. Probably
not in a big Wowee Performance Moment, but hey.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12899
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#12934
These are the changes for FreeBSD corresponding to the changes made for
Linux in #12863, see that PR for details.
Changes from #12863 are applied for zvol_geom_open and zvol_cdev_open
on FreeBSD. This also adds a check for the zvol dying which we had
in zvol_geom_open but was missing in zvol_cdev_open. The check causes
the open to fail early with ENXIO when we are in the middle of changing
volmode.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#12934
Fix from https://github.com/openzfs/zfs/pull/12844#discussion_r774179413
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12905
sc.nr_to_scan is an input to super_cache_clean (via
shrinker->scan_objects), used to set the number of objects to scan
in the various caches. However super_cache_scan also modifies
sc.nr_to_scan, so when used in a loop we need to reset
sc.nr_to_scan back to our desired nr_to_scan for the next
iteration.
Issue discovered and solution suggested by
Tenzin Lhakhang @tlhakhan.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chris Dunlop <chris@onthe.net.au>
Issue #12433Closes#12908
When performing I/O on FreeBSD using a file based vdev ensure all
errors encountered when reading/writing are propagated through the
zio pipeline.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12904
Provide access to file generation number on Linux.
Add test coverage.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#12856
When restructuring the zvol_open() logic for the Linux 5.13 kernel
a lock inversion was accidentally introduced. In the updated code
the spa_namespace_lock is now taken before the zv_suspend_lock
allowing the following scenario to occur:
down_read <=== waiting for zv_suspend_lock
zvol_open <=== holds spa_namespace_lock
__blkdev_get
blkdev_get_by_dev
blkdev_open
...
mutex_lock <== waiting for spa_namespace_lock
spa_open_common
spa_open
dsl_pool_hold
dmu_objset_hold_flags
dmu_objset_hold
dsl_prop_get
dsl_prop_get_integer
zvol_create_minor
dmu_recv_end
zfs_ioc_recv_impl <=== holds zv_suspend_lock via zvol_suspend()
zfs_ioc_recv
...
This commit resolves the issue by moving the acquisition of the
spa_namespace_lock back to after the zv_suspend_lock which restores
the original ordering.
Additionally, as part of this change the error exit paths were
simplified where possible.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Rich Ercolani <rincebrain@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12863
A recent commit to FreeBSD changed the type of
vop_readdir_args.a_cookies to a uint64_t**. There is no functional
impact to ZFS because ZFS only uses 32-bit cookies, which will be
zero-extended to 64-bits by the existing code.
b214fcceac
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Alan Somers <asomers@gmail.com>
Closes#12874
va_seq was actually a thin veil over va_gen, so z_gen is a more
appropriate value than z_seq to populate the field with.
Drop the unnecessary compat obfuscation and provide the correct
file generation number.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <freqlabs@freebsd.org>
Closes#12851
When rolling back a dataset, ZFS has to purge file data resident in the
system page cache. To do this, it loops over all vnodes for the
mountpoint and calls vn_pages_remove() to purge pages associated with
the vnode's VM object. Each page is thus exclusively busied while the
dataset's teardown write lock is held.
When handling a page fault on a mapped ZFS file, FreeBSD's page fault
handler busies newly allocated pages and then uses VOP_GETPAGES to fill
them. The ZFS getpages VOP acquires the teardown read lock with vnode
pages already busied. This represents a lock order reversal which can
lead to deadlock.
To break the deadlock, observe that zfs_rezget() need only purge those
pages marked valid, and that pages busied by the page fault handler are,
by definition, invalid. Furthermore, ZFS pages always transition from
invalid to valid with the teardown lock held, and ZFS never creates
partially valid pages. Thus, zfs_rezget() can use the new
vn_pages_remove_valid() to skip over pages busied by the fault handler.
PR: 258208
Tested by: pho
Reviewed by: avg, sef, kib
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D32931
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#12828
The definition of struct blkcg_gq was moved into blk-cgroup.h, which is
a header that's been in Linux since 2015. This is used by
vdev_blkg_tryget() in module/os/linux/zfs/vdev_disk.c. Since the kernel
for CentOS 7 and similar-generation releases doesn't have this header,
its inclusion is guarded by a configure test.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#12819
This change adds a confiugre check to determine if bio_set_dev is a
helper macro or not. If not, then the attempt to override its internal
call to bio_associate_blkg(), with a macro definition to our own
version, is no longer possible, as the compiler won't use it when
compiling the new inline function replacement implemented in the header.
This change also creates a new vdev_bio_set_dev() function that performs
the same work, and also performs the work implemented in
vdev_bio_associate_blkg(), as it is the only thing calling that function
in our code. Our custom vdev_bio_associate_blkg() is now only compiled
if the bio_set_dev() is a macro in the Linux headers.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#12819
The iov_iter->type member was renamed iov_iter->iter_type. However,
while looking into this, realized that in 2018 a iov_iter_type(*iov)
accessor function was introduced. So if that is present, use it,
otherwise fall back to trying the existing behavior of directly
accessing type from iov_iter.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#12819
The return type for the submit_bio member of struct
block_device_operations was changed to no longer return a value.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#12819
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#12728
Due to a possible lock inversion the zvol open call path on Linux
needs to be able to retry in the case where the spa_namespace_lock
cannot be acquired.
For Linux 5.12 an older kernel this was accomplished by returning
-ERESTARTSYS from zvol_open() to request that blkdev_get() drop
the bdev->bd_mutex lock, reaquire it, then call the open callback
again. However, as of the 5.13 kernel this behavior was removed.
Therefore, for 5.12 and older kernels we preserved the existing
retry logic, but for 5.13 and newer kernels we retry internally in
zvol_open(). This should always succeed except in the case where
a pool's vdev are layed on zvols, in which case it may fail. To
handle this case vdev_disk_open() has been updated to retry when
opening a device when -ERESTARTSYS is returned.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #12301Closes#12759
Add properties, similar to pool properties, to each vdev.
This makes use of the existing per-vdev ZAP that was added as
part of device evacuation/removal.
A large number of read-only properties are exposed,
many of the members of struct vdev_t, that provide useful
statistics.
Adds support for read-only "removing" vdev property.
Adds the "allocating" property that defaults to "on" and
can be set to "off" to prevent future allocations from that
top-level vdev.
Supports user-defined vdev properties.
Includes support for properties.vdev in SYSFS.
Co-authored-by: Allan Jude <allan@klarasystems.com>
Co-authored-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Closes#11711
Instead, linux/pagemap.h offers a number of folio-specific functions to
be called instead. In this case, module/os/linux/zfs/zfs_vnops_os.c
wants to call wait_on_page_bit(pp, PG_writeback). This gets replaced
with folio_wait_bit(folio_page(pp), PG_writeback). This change modifies
the code to conditionally compile that if configure identifies th
presence of the folio_wait_bit() function.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#12800
- To avoid a use-after-free, zfsvfs->z_log needs to be loaded after the
teardown lock is acquired with ZFS_ENTER().
- Avoid leaking vnode locks in zfs_rename_relock() and zfs_rename_()
when the ZFS_ENTER() macros forces an early return.
Refactor the rename implementation so that ZFS_ENTER() can be used
safely. As a bonus, this lets us use the ZFS_VERIFY_ZP() macro instead
of open-coding its implementation.
Reported-by: Peter Holm <pho@FreeBSD.org>
Tested-by: Peter Holm <pho@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Sponsored-by: The FreeBSD Foundation
Closes#12717
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#12771
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Pawel Jakub Dawidek <pawel@dawidek.net>
Closes#12748
The submit_bio() prototype has changed again. The version is 5.16
still only expects a single argument but the return type has changed
to void. Since we never used the returned value before update the
configure check to detect both single arg versions.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12725
On Linux, sometimes, when ZFS goes to unmount an automounted snap,
it fails a VERIFY check on debug builds, because taskq_cancel_id
returned ENOENT after not finding the taskq it was trying to cancel.
This presumably happens when it already died for some reason; in this
case, we don't really mind it already being dead, since we're just
going to dispatch a new task to unmount it right after.
So we just ignore it if we get back ENOENT trying to cancel here,
retry a couple times if we get back the only other possible condition
(EBUSY), and log to dbgmsg if we got anything but ENOENT or success.
(We also add some locking around taskqid, to avoid one or two cases
of two instances of trying to cancel something at once.)
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#11632Closes#12670
We move the spinlock unlock before the thread creation. This should be
safe because the thread creation code doesn't actually manipulate any
taskq data structures; that's done by the thread once it's created.
We also remove the assertion that the maxthreads is the current threads
plus one; that assertion could fail if multiple hotplug events come in
quick succession, and the first new taskq thread hasn't had a chance to
start processing yet.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
eviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#12714
We have to hold the teardown lock while dereferencing zfsvfs->z_os and,
I believe, when committing to the ZIL.
Note that jumping to the "out" label, "error" is always non-zero.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#12704
The objset object is reallocated during certain dataset operations, such
as rollbacks, so the objset pointer must be loaded after acquiring the
teardown lock.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#12704
Make the main dmu_buf_hold_array() function non-static.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Pawel Jakub Dawidek <pawel@dawidek.net>
Closes#12628
While switching abd_zero_buf allocation KPI I've missed the fact
that kmem_zalloc() zeroed the allocation, while kmem_cache_alloc()
does not. Add explicit bzero() after it.
I don't think it should have caused real problems, but leaking one
memory page content all over the pool is not good.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#12569
When mounting a snapshot in the .zfs/snapshots control directory,
temporarily assume roots credentials to perform the VFS_MOUNT().
This allows regular users and users inside jails to access these
snapshots.
The regular usermount code is not helpful here, since it requires
that the user performing the mount own the mountpoint, which won't
be the case for .zfs/snapshot/<snapname>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Sponsored-By: Modirum MDPay
Sponsored-By: Klara Inc.
Closes#11312
As of the Linux 5.9 kernel a fallthrough macro has been added which
should be used to anotate all intentional fallthrough paths. Once
all of the kernel code paths have been updated to use fallthrough
the -Wimplicit-fallthrough option will because the default. To
avoid warnings in the OpenZFS code base when this happens apply
the fallthrough macro.
Additional reading: https://lwn.net/Articles/794944/
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12441
Kernel commits
332f606b32b6 ovl: enable RCU'd ->get_acl()
0cad6246621b vfs: add rcu argument to ->get_acl() callback
Added compatibility code to detect the new ->get_acl() interface
and correctly handle the case where the new rcu argument is set.
Reviewed-by: Coleman Kane <ckane@colemankane.org>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12548
We attempt to remove an existing SA xattr when setting a dir xattr, but
this only makes sense if the znode has been upgraded to the SA format.
Otherwise, we will hit an assert in zfs_sa_get_xattr.
Make sure this is an SA znode before attempting to remove the SA xattr.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#12514
This adds supports for hole-punching facilities in the FreeBSD kernel
starting from __FreeBSD_version 1400032.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Ka Ho Ng <khng@FreeBSD.org>
Sponsored-by: The FreeBSD Foundation
Closes#12458
Linux 4.11 added a new statx system call that allows us to expose crtime
as btime. We do this by caching crtime in the znode to match how atime,
ctime and mtime are cached in the inode.
statx also introduced a new way of reporting whether the immutable,
append and nodump bits have been set. It adds support for reporting
compression and encryption, but the semantics on other filesystems is
not just to report compression/encryption, but to allow it to be turned
on/off at the file level. We do not support that.
We could implement semantics where we refuse to allow user modification
of the bit, but we would need to do a dnode_hold() in zfs_znode_alloc()
to find out encryption/compression information. That would introduce
locking that will have a minor (although unmeasured) performance cost.
It also would be inferior to zdb, which reports far more detailed
information. We therefore omit reporting of encryption/compression
through statx in favor of recommending that users interested in such
information use zdb.
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Richard Yao <ryao@gentoo.org>
Closes#8507
When a header is allocated for full overwrite it is a waste of time
to allocate b_pabd/b_rabd for it, since arc_write() will free them
without ever being touched. If it is a read or a partial overwrite
then arc_read() and arc_hdr_decrypt() allocate them explicitly.
Reduced memory allocation in user threads also reduces ARC eviction
throttling there, proportionally increasing it in ZIO threads, that
is not good. To minimize or even avoid it introduce ARC allocation
reserve, allowing certain arc_get_data_abd() callers to allocate a
bit longer in situations where user threads will already throttle.
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12398
Before OpenZFS 2.0, trying to set the FreeBSD sysctl vfs.zfs.arc_max
to a disallowed value would return an error.
Since the switch, it instead only generates WARN_IF_TUNING_IGNORED
Keep the ability to set the sysctl's specifically to 0, even though
that is less than the minimum, because some tests depend on this.
Also lost, was the ability to set vfs.zfs.arc_max to a value less
than the default vfs.zfs.arc_min at boot time. Restore this as well.
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Closes#12161
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Martin Matuska <mm@FreeBSD.org>
Co-authored-by: Konstantin Belousov <kib@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
External-issue: https://reviews.freebsd.org/D31207Closes#12442
The /proc/diskstats accounting needs to be explicitly enabled
for block devices which do not use multi-queue.
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12440Closes#12066
CpaDcGeneratefooter function that obtain the checksum code
does not support the CPA_DC_STATELESS mode. So we get the
adler32 chencksum of the end of the zlib from dc_results.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Chengfei Zhu <chengfeix.zhu@intel.com>
Signed-off-by: hedong.zhang <h_d_zhang@163.com>
Closes#12343
We have a tunable which permits one to disable the use of unmapped I/O
for the buffer cache. Respect it in ZFS as well. This is useful for
KMSAN, which cannot easily maintain shadow state for unmapped pages.
No functional change intended, as unmapped I/O is permitted by default
and there's no real reason to disable it in practice except for
debugging.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#12446
It is wrong for arc_write_ready() to use zfs_abd_scatter_enabled to
decide whether to reallocate/copy the buffer, because the answer is
OS-specific and depends on the buffer size. Instead of that use
abd_size_alloc_linear(), moved into public header.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#12425
These were mostly used to annotate do {} while(0)s
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Issue #12201
This includes a simplification of mkbusy and format correctness in zhack
and ztest
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Issue #12201
Kernel 5.14 introduced a change where set_page_dirty of
struct address_space_operations is no longer implicitly set to
__set_page_dirty_buffers(), which ended up resulting in a NULL
pointer deref in the kernel when it is attempted to be called.
This change sets .set_page_dirty in the structure to
__set_page_dirty_nobuffers(), which was introduced with the
related patch set. The breaking change was introduce in commit
0af573780b0b13fceb7fabd49dc1b073cee9a507 to torvalds/linux.git.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#12427
