When growing the size of a (VMEM or KVMEM) kmem cache, spl_cache_grow()
always does taskq_dispatch(spl_cache_grow_work), and then waits for the
KMC_BIT_GROWING to be cleared by the taskq thread.
The taskq thread (spl_cache_grow_work()) does:
1. allocate new slab and add to list
2. wake_up_all(skc_waitq)
3. clear_bit(KMC_BIT_GROWING)
Therefore, the waiting thread can wake up before GROWING has been
cleared. It will see that the growing has not yet completed, and go
back to sleep until it hits the 100ms timeout.
This can have an extreme performance impact on workloads that alloc/free
more than fits in the (statically-sized) magazines. These workloads
allocate and free slabs with high frequency.
The problem can be observed with `funclatency spl_cache_grow`, which on
some workloads shows that 99.5% of the time it takes <64us to allocate
slabs, but we spend ~70% of our time in outliers, waiting for the 100ms
timeout.
The fix is to do `clear_bit(KMC_BIT_GROWING)` before
`wake_up_all(skc_waitq)`.
A future investigation should evaluate if we still actually need to
taskq_dispatch() at all, and if so on which kernel versions.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Wilson <gwilson@delphix.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#9989
If a device is participating in an active resilver, then it will have a
non-empty DTL. Operations like vdev_{open,reopen,probe}() can cause the
resilver to be restarted (or deferred to be restarted later), which is
unnecessary if the DTL is still covered by the current scan range. This
is similar to the logic in vdev_dtl_should_excise() where the DTL can
only be excised if it's max txg is in the resilvered range.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Gallagher <john.gallagher@delphix.com>
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Signed-off-by: John Poduska <jpoduska@datto.com>
Issue #840Closes#9155Closes#9378Closes#9551Closes#9588
When qat_compress() fails to allocate the required contiguous memory
it mistakenly returns success. This prevents the fallback software
compression from taking over and (un)compressing the block.
Resolve the issue by correctly setting the local 'status' variable
on all exit paths. Furthermore, initialize it to CPA_STATUS_FAIL
to ensure qat_compress() always fails safe to guard against any
similar bugs in the future.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9784Closes#9788
- Skip invalid DVAs when importing pools in readonly mode
(in addition to when the config is untrusted).
- Upon encountering a DVA with a null VDEV, fail gracefully
instead of panicking with a NULL pointer dereference.
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Steve Mokris <smokris@softpixel.com>
Closes#9022
Any running 'zpool initialize' or TRIM must be cancelled prior
to the vdev_metaslab_fini() call in spa_vdev_remove_log() which
will unload the metaslabs and set ms->ms_group == NULL.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8602Closes#9751
This change leverage module_param_call() to run arc_tuning_update()
immediately after the ARC tunable has been updated as suggested in
cffa837 code review.
A simple test case is added to the ZFS Test Suite to prevent future
regressions in functionality.
This is a backport of #9489 provided from:
https://github.com/zfsonlinux/zfs/pull/9776#issuecomment-569418370
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Move the 'nvh = (void *)buf' assignment after the 'buf == NULL'
check to resolve the warning. Interestingly, cppcheck 1.88
correctly determines that the existing code is safe, while
cppcheck 1.86 reports the warning.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9732
Suppress autoVariables warnings in the lua interpreter. The usage
here while unconventional in intentional and the same as upstream.
[module/lua/ldebug.c:327]: (error) Address of local auto-variable
assigned to a function parameter.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9732
The dnp argument can only be set to NULL when the DNODE_DRY_RUN flag
is set. In which case, an early return path will be executed and a
NULL pointer dereference at the given location is impossible. Add
an additional ASSERT to silence the cppcheck warning and document
that dbp must never be NULL at the point in the function.
[module/zfs/dnode.c:1566]: (warning) Possible null pointer deref: dnp
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9732
As of cppcheck 1.82 surpress the warning regarding shifting too many
bits for __divdi3() implemention. The algorithm used here is correct.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9732
As of cppcheck 1.82 warnings are issued when using the list_for_each_*
functions with an uninitialized variable. Functionally, this is fine
but to resolve the warning initialize these variables.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9732
Resolve the following uninitialized variable warnings. In practice
these were unreachable due to the goto. Replacing the goto with a
return resolves the warning and yields more readable code.
[module/icp/algs/modes/ccm.c:892]: (error) Uninitialized variable: ccm_param
[module/icp/algs/modes/ccm.c:893]: (error) Uninitialized variable: ccm_param
[module/icp/algs/modes/gcm.c:564]: (error) Uninitialized variable: gcm_param
[module/icp/algs/modes/gcm.c:565]: (error) Uninitialized variable: gcm_param
[module/icp/algs/modes/gcm.c:599]: (error) Uninitialized variable: gmac_param
[module/icp/algs/modes/gcm.c:600]: (error) Uninitialized variable: gmac_param
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9732
Apply umask to `mode` which will eventually be applied to inode.
This is needed since VFS doesn't apply umask for O_TMPFILE files.
(Note that zpl_init_acl() applies `ip->i_mode &= ~current_umask();`
only when POSIX ACL is used.)
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@gmail.com>
Closes#8997Closes#8998
Currently, 'zfs list' and 'zfs get' commands can be slow when
working with snapshots that have a ds_props_obj. This is
because the code that discovers all of the properties for these
snapshots needs to read this object for each snapshot, which
almost always ends up causing an extra random synchronous read
for each snapshot. This performance penalty exists even if the
properties on that snapshot have been unset because the object
is normally only freed when the snapshot is freed, even though
it is only created when it is needed.
This patch allows the user to regain 'zfs list' performance on
these snapshots by destroying the ds_props_obj when it no longer
has any entries left. In practice on a production machine, this
optimization seems to make 'zfs list' about 55% faster.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Paul Zuchowski <pzuchowski@datto.com>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#9704
After spa_vdev_remove_aux() is called, the config nvlist is no longer
valid, as it's been replaced by the new one (with the specified device
removed). Therefore any pointers into the nvlist are no longer valid.
So we can't save the result of
`fnvlist_lookup_string(nv, ZPOOL_CONFIG_PATH)` (in vd_path) across the
call to spa_vdev_remove_aux().
Instead, use spa_strdup() to save a copy of the string before calling
spa_vdev_remove_aux.
Found by AddressSanitizer:
ERROR: AddressSanitizer: heap-use-after-free on address ...
READ of size 34 at 0x608000a1fcd0 thread T686
#0 0x7fe88b0c166d (/usr/lib/x86_64-linux-gnu/libasan.so.4+0x5166d)
#1 0x7fe88a5acd6e in spa_strdup spa_misc.c:1447
#2 0x7fe88a688034 in spa_vdev_remove vdev_removal.c:2259
#3 0x55ffbc7748f8 in ztest_vdev_aux_add_remove ztest.c:3229
#4 0x55ffbc769fba in ztest_execute ztest.c:6714
#5 0x55ffbc779a90 in ztest_thread ztest.c:6761
#6 0x7fe889cbc6da in start_thread
#7 0x7fe8899e588e in __clone
0x608000a1fcd0 is located 48 bytes inside of 88-byte region
freed by thread T686 here:
#0 0x7fe88b14e7b8 in __interceptor_free
#1 0x7fe88ae541c5 in nvlist_free nvpair.c:874
#2 0x7fe88ae543ba in nvpair_free nvpair.c:844
#3 0x7fe88ae57400 in nvlist_remove_nvpair nvpair.c:978
#4 0x7fe88a683c81 in spa_vdev_remove_aux vdev_removal.c:185
#5 0x7fe88a68857c in spa_vdev_remove vdev_removal.c:2221
#6 0x55ffbc7748f8 in ztest_vdev_aux_add_remove ztest.c:3229
#7 0x55ffbc769fba in ztest_execute ztest.c:6714
#8 0x55ffbc779a90 in ztest_thread ztest.c:6761
#9 0x7fe889cbc6da in start_thread
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#9706
This interferes with zdb_read_block trying all the decompression
algorithms when the 'd' flag is specified, as some are
expected to fail. Also control the output when guessing
algorithms, try the more common compression types first, allow
specifying lsize/psize, and fix an uninitialized variable.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Zuchowski <pzuchowski@datto.com>
Closes#9612Closes#9630
This change allows us to align the code dump logic across platforms.
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Don Brady <don.brady@delphix.com>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9691
Update the vdev_disk_open() retry logic to use a specified number
of milliseconds to be more robust. Additionally, on failure log
both the time waited and requested timeout to the internal log.
The default maximum allowed open retry time has been increased
from 500ms to 1000ms.
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9680
Conflicts:
In case L2ARC read failed, l2arc_read_done() creates _different_ ZIO
to read data from the original storage device. Unfortunately pointer
to the failed ZIO remains in hdr->b_l1hdr.b_acb->acb_zio_head, and if
some other read try to bump the ZIO priority, it will crash.
The problem is reproducible by corrupting L2ARC content and reading
some data with prefetch if l2arc_noprefetch tunable is changed to 0.
With the default setting the issue is probably not reproducible now.
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#9648
There may be circumstances where it's desirable that all blocks
in a specified dataset be stored on the special device. Relax
the artificial 128K limit and allow the special_small_blocks
property to be set up to 1M. When blocks >1MB have been enabled
via the zfs_max_recordsize module option, this limit is increased
accordingly.
Reviewed-by: Don Brady <don.brady@delphix.com>
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9131Closes#9355
Remove the specific gitignore rules for module left-overs and add a
generic one in modules/.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Closes#9656
As described in commit f81d5ef6 the zfs_vdev_elevator module
option is being removed. Users who require this functionality
should update their systems to set the disk scheduler using a
udev rule.
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #8664Closes#9417Closes#9609
The changes in commit 41e1aa2a / PR #9583 introduced a regression on
tmpfile_001_pos: fsetxattr() on a O_TMPFILE file descriptor started
to fail with errno ENODATA:
openat(AT_FDCWD, "/test", O_RDWR|O_TMPFILE, 0666) = 3
<...>
fsetxattr(3, "user.test", <...>, 64, 0) = -1 ENODATA
The originally proposed change on PR #9583 is not susceptible to it,
so just move the code/if-checks around back in that way, to fix it.
Reviewed-by: Pavel Snajdr <snajpa@snajpa.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Original-patch-by: Heitor Alves de Siqueira <halves@canonical.com>
Signed-off-by: Mauricio Faria de Oliveira <mfo@canonical.com>
Closes#9602
If zp->z_unlinked is set, we're working with a znode that has been
marked for deletion. If that's the case, we can skip the "goto again"
loop and return ENOENT, as the znode should not be discovered.
Reviewed-by: Richard Yao <ryao@gentoo.org>
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Heitor Alves de Siqueira <halves@canonical.com>
Closes#9583
blkg_tryget() as shipped in EL8 kernels does not seem to handle NULL
@blkg as input; this is different from its mainline counterpart where
NULL is accepted. To prevent dereferencing a NULL pointer when dealing
with block devices which do not set a root_blkg on the request queue
perform the NULL check in vdev_bio_associate_blkg().
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#9546Closes#9577
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Ahrens <matt@delphix.com>
Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Closes#9034
Before my ZIL space optimization few years ago 128KB writes were logged
as two 64KB+ records in two 128KB log blocks. After that change it
became ~127KB+/1KB+ in two 128KB log blocks to free space in the second
block for another record. Unfortunately in case of 128KB only writes,
when space in the second block remained unused, that change increased
write latency by unbalancing checksum computation and write times
between parallel threads. It also didn't help with SLOG space
efficiency in that case.
This change introduces new 68KB log block size, used for both writes
below 67KB and 128KB-sharp writes. Writes of 68-127KB are still using
one 128KB block to not increase processing overhead. Writes above
131KB are still using full 128KB blocks, since possible saving there
is small. Mixed loads will likely also fall back to previous 128KB,
since code uses maximum of the last 16 requested block sizes.
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#9409
Address two prototype related warnings emitted by clang.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9535
Currently, when you call 'zfs change-key' on an encrypted dataset
that has an unencrypted child, the code will trigger a VERIFY.
This VERIFY is leftover from before we allowed unencrypted
datasets to exist underneath encrypted ones. This patch fixes the
issue by simply replacing the VERIFY with an early return when
recursing through datasets.
Reviewed by: Jason King <jason.brian.king@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#9524
Currently, for certain sizes and classes of allocations we use
SPL caches that are backed by caches in the Linux Slab allocator
to reduce fragmentation and increase utilization of memory. The
way things are implemented for these caches as of now though is
that we don't keep any statistics of the allocations that we
make from these caches.
This patch enables the tracking of allocated objects in those
SPL caches by making the trade-off of grabbing the cache lock
at every object allocation and free to update the respective
counter.
Additionally, this patch makes those caches visible in the
/proc/spl/kmem/slab special file.
As a side note, enabling the specific counter for those caches
enables SDB to create a more user-friendly interface than
/proc/spl/kmem/slab that can also cross-reference data from
slabinfo. Here is for example the output of one of those
caches in SDB that outputs the name of the underlying Linux
cache, the memory of SPL objects allocated in that cache,
and the percentage of those objects compared to all the
objects in it:
```
> spl_kmem_caches | filter obj.skc_name == "zio_buf_512" | pp
name ... source total_memory util
----------- ... ----------------- ------------ ----
zio_buf_512 ... kmalloc-512[SLUB] 16.9MB 8
```
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Closes#9474
When "feature@allocation_classes" is not enabled on the pool no vdev
with "special" or "dedup" allocation type should be allowed to exist in
the vdev tree.
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#9427Closes#9429
If stdin if empty - don't run xargs command,
otherwise we can get `cp: missing file operand`
error.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Melikov <mail@gmelikov.ru>
Closes#9418
Commit 093bb64 resolved an automount failures for chroot'd processes
but inadvertently broke automounting for root filesystems where the
vfs_mntpoint is NULL. Resolve the issue by checking for NULL in order
to generate the correct path.
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9381Closes#9384
A rangelock KPI already exists on FreeBSD. Add a zfs_ prefix as
per our convention to prevent any conflict with existing symbols.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9402
Restore the SIMD optimization for 4.19.38 LTS, 4.14.120 LTS,
and 5.0 and newer kernels.
This commit squashes the following commits from master in to
a single commit which can be applied to 0.8.2.
10fa2545 - Linux 4.14, 4.19, 5.0+ compat: SIMD save/restore
b88ca2ac - Enable SIMD for encryption
095b5412 - Fix CONFIG_X86_DEBUG_FPU build failure
e5db3134 - Linux 5.0 compat: SIMD compatibility
Reviewed-by: Fabian Grünbichler <f.gruenbichler@proxmox.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
TEST_ZIMPORT_SKIP="yes"
Originally the zfs_vdev_elevator module option was added as a
convenience so the requested elevator would be automatically set
on the underlying block devices. At the time this was simple
because the kernel provided an API function which did exactly this.
This API was then removed in the Linux 4.12 kernel which prompted
us to add compatibly code to set the elevator via a usermodehelper.
While well intentioned this introduced a bug which could cause a
system hang, that issue was subsequently fixed by commit 2a0d4188.
In order to avoid future bugs in this area, and to simplify the code,
this functionality is being deprecated. A console warning has been
added to notify any existing consumers and the documentation updated
accordingly. This option will remain for the lifetime of the 0.8.x
series for compatibility but if planned to be phased out of master.
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #8664Closes#9317
Trying to 'zfs diff' a snapshot with large dnodes will incorrectly try
to access its interior slots when dnodesize > sizeof(dnode_phys_t).
This is normally not an issue because the interior slots are
zero-filled, which report_dnode() handles calling
report_free_dnode_range(). However this is not the case for encrypted
large dnodes or filesystem using many SA based xattrs where the extra
data past the legacy dnode size boundary is interpreted as a
dnode_phys_t.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#7678Closes#8931Closes#9343
This commit fixes a NULL pointer dereference triggered in
spa_vdev_remove_top_check() by trying to "zpool remove" an indirect
vdev.
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#9327
Currently, spa_keystore_change_key_sync_impl() does not recurse
into clones when updating encryption roots for either a call to
'zfs promote' or 'zfs change-key'. This can cause children of
these clones to end up in a state where they point to the wrong
dataset as the encryption root. It can also trigger ASSERTs in
some cases where the code checks reference counts on wrapping
keys. This patch fixes this issue by ensuring that this function
properly recurses into clones during processing.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alek Pinchuk <apinchuk@datto.com>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#9267Closes#9294
Currently, the DSL scan code figures out when it should suspend
processing and allow a txg to continue by calling the function
dsl_scan_check_suspend(). Unfortunately, this function only
allows the scan to suspend at a level 0 block. In the event that
the system is scanning a bunch of empty snapshots or a resilver
is running with a high enough scn_cur_min_txg, the scan will
stop processing each dataset at the root level, deciding it
has nothing left to do. This means that the check_suspend
function is never called and the txg remains stuck until a
dataset is found that has data to scan.
This patch fixes the problem by allowing scans to suspend at
the root level of the objset. For backwards compatibility, we
use the bookmark <objsetid, 0, 0, 0> when we suspend here so
that older versions of the code will work as intended.
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#9300
Account for ZFS_MAX_DATASET_NAME_LEN in kstat data size. This value
is ignored in the Linux kstat code but resolves the issue for other
platforms.
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Igor Kozhukhov <igor@dilos.org>
Closes#9254Closes#9151
When running on larger memory systems, we can overflow the value of
maxinflight. This can result in maxinflight having a value of 0 causing
the system to hang.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Wilson <george.wilson@delphix.com>
Closes#9272
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Closes#9240
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Closes#9241
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Closes#9239
If a pool enables the SPACEMAP_HISTOGRAM feature shortly before being
exported, we can enter a situation that causes a kernel panic. Any metaslabs
that are loaded during the final dirty txg and haven't already been condensed
will cause metaslab_sync to proceed after the final dirty txg so that the
condense can be performed, which there are assertions to prevent. Because of
the nature of this issue, there are a number of ways we can enter this
state. Rather than try to prevent each of them one by one, potentially missing
some edge cases, we instead cut it off at the point of intersection; by
preventing metaslab_sync from proceeding if it would only do so to perform a
condense and we're past the final dirty txg, we preserve the utility of the
existing asserts while preventing this particular issue.
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#9185Closes#9186Closes#9231Closes#9253
For interrupt coalescing, cv_timedwait_hires() uses a 100us slack/delta
for calls to schedule_hrtimeout_range(). This 100us slack can be costly
for small writes.
This change improves small write performance by passing resolution `res`
parameter to schedule_hrtimeout_range() to be used as delta/slack. A new
tunable `spl_schedule_hrtimeout_slack_us` is added to preserve old
behavior when desired.
Performance observations on 8K recordsize filesystem:
- 8K random writes at 1-64 threads, up to 60% improvement for one thread
and smaller gains as thread count increases. At >64 threads, 2-5%
decrease in performance was observed.
- 8K sequential writes, similar 60% improvement for one thread and
leveling out around 64 threads. At >64 threads, 5-10% decrease in
performance was observed.
- 128K sequential write sees 1-5 for the 128K. No observed regression at
high thread count.
Testing done on Ubuntu 18.04 with 4.15 kernel, 8vCPUs and SSD storage on
VMware ESX.
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Signed-off-by: Tony Nguyen <tony.nguyen@delphix.com>
Closes#9217
There are two different deadlock scenarios, but they share a common
link, which is
thread 1 holding sa_lock and trying to get zap->zap_rwlock:
zap_lockdir_impl+0x858/0x16c0 [zfs]
zap_lockdir+0xd2/0x100 [zfs]
zap_lookup_norm+0x7f/0x100 [zfs]
zap_lookup+0x12/0x20 [zfs]
sa_setup+0x902/0x1380 [zfs]
zfsvfs_init+0x3d6/0xb20 [zfs]
zfsvfs_create+0x5dd/0x900 [zfs]
zfs_domount+0xa3/0xe20 [zfs]
and thread 2 trying to get sa_lock, either in sa_setup:
sa_setup+0x742/0x1380 [zfs]
zfsvfs_init+0x3d6/0xb20 [zfs]
zfsvfs_create+0x5dd/0x900 [zfs]
zfs_domount+0xa3/0xe20 [zfs]
or in sa_build_index:
sa_build_index+0x13d/0x790 [zfs]
sa_handle_get_from_db+0x368/0x500 [zfs]
zfs_znode_sa_init.isra.0+0x24b/0x330 [zfs]
zfs_znode_alloc+0x3da/0x1a40 [zfs]
zfs_zget+0x39a/0x6e0 [zfs]
zfs_root+0x101/0x160 [zfs]
zfs_domount+0x91f/0xea0 [zfs]
From there, there are different locking paths back to something
holding zap->zap_rwlock.
The deadlock scenarios involve multiple different ZFS filesystems
being mounted. sa_lock is common to these scenarios, and the sa
struct involved is private to a mount. Therefore, these must be
referring to different sa_lock instances and these deadlocks can't
occur in practice.
The fix, from Brian Behlendorf, is to remove sa_lock from lockdep
coverage by initializing it with MUTEX_NOLOCKDEP.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jeff Dike <jdike@akamai.com>
Closes#9110
