The const keyword was added to the 'struct xattr_handler' in the
generic Linux super_block structure. To handle this we define an
appropriate xattr_handler_t typedef which can be used. This was
the preferred solution because it keeps the code clean and readable.
ZFS even under Solaris does not strictly require libshare to be
available. The current implementation attempts to dlopen() the
library to access the needed symbols. If this fails libshare
support is simply disabled.
This means that on Linux we only need the most minimal libshare
implementation. In fact just enough to prevent the build from
failing. Longer term we can decide if we want to implement a
libshare library like Solaris. At best this would be an abstraction
layer between ZFS and NFS/SMB. Alternately, we can drop libshare
entirely and directly integrate ZFS with Linux's NFS/SMB.
Finally the bare bones user-libshare.m4 test was dropped. If we
do decide to implement libshare at some point it will surely be
as part of this package so the check is not needed.
If libselinux is detected on your system at configure time link
against it. This allows us to use a library call to detect if
selinux is enabled and if it is to pass the mount option:
"context=\"system_u:object_r:file_t:s0"
For now this is required because none of the existing selinux
policies are aware of the zfs filesystem type. Because of this
they do not properly enable xattr based labeling even though
zfs supports all of the required hooks.
Until distro's add zfs as a known xattr friendly fs type we
must use mntpoint labeling. Alternately, end users could modify
their existing selinux policy with a little guidance.
It turns out that 'zpool events' over 1024 bytes in size where being
silently dropped. This was discovered while writing the zfault.sh
tests to validate common failure modes.
This could occur because the zfs interface for passing an arbitrary
size nvlist_t over an ioctl() is to provide a buffer for the packed
nvlist which is usually big enough. In this case 1024 byte is the
default. If the kernel determines the buffer is to small it returns
ENOMEM and the minimum required size of the nvlist_t. This was
working properly but in the case of 'zpool events' the event stream
was advanced dispite the error. Thus the retry with the bigger
buffer would succeed but it would skip over the previous event.
The fix is to pass this size to zfs_zevent_next() and determine
before removing the event from the list if it will fit. This was
preferable to checking after the event was returned because this
avoids the need to rewind the stream.
While there is no right maximum timeout for a disk IO we can start
laying the ground work to measure how long they do take in practice.
This change simply measures the IO time and if it exceeds 30s an
event is posted for 'zpool events'.
This value was carefully selected because for sd devices it implies
that at least one timeout (SD_TIMEOUT) has occured. Unfortunately,
even with FAILFAST set we may retry and request and not get an
error. This behavior is strongly dependant on the device driver
and how it is hooked in to the scsi error handling stack. However
by setting the limit at 30s we can log the event even if no error
was returned.
Slightly longer term we can start recording these delays perhaps
as a simple power-of-two histrogram. This histogram can then be
reported as part of the 'zpool status' command when given an command
line option.
None of this code changes the internal behavior of ZFS. Currently
it is simply for reporting excessively long delays.
ZFS works best when it is notified as soon as possible when a device
failure occurs. This allows it to immediately start any recovery
actions which may be needed. In theory Linux supports a flag which
can be set on bio's called FAILFAST which provides this quick
notification by disabling the retry logic in the lower scsi layers.
That's the theory at least. In practice is turns out that while the
flag exists you oddly have to set it with the BIO_RW_AHEAD flag.
And even when it's set it you may get retries in the low level
drivers decides that's the right behavior, or if you don't get the
right error codes reported to the scsi midlayer.
Unfortunately, without additional kernels patchs there's not much
which can be done to improve this. Basically, this just means that
it may take 2-3 minutes before a ZFS is notified properly that a
device has failed. This can be improved and I suspect I'll be
submitting patches upstream to handle this.
By default the Solaris code does not log speculative or soft io errors
in either 'zpool status' or post an event. Under Linux we don't want
to change the expected behavior of 'zpool status' so these io errors
are still suppressed there.
However, since we do need to know about these events for Linux FMA and
the 'zpool events' interface is new we do post the events. With the
addition of the zio_flags field the posted events now contain enough
information that a user space consumer can identify and discard these
events if it sees fit.
One of the neat tricks an autoconf style project is capable of
is allow configurion/building in a directory other than the
source directory. The major advantage to this is that you can
build the project various different ways while making changes
in a single source tree.
For example, this project is designed to work on various different
Linux distributions each of which work slightly differently. This
means that changes need to verified on each of those supported
distributions perferably before the change is committed to the
public git repo.
Using nfs and custom build directories makes this much easier.
I now have a single source tree in nfs mounted on several different
systems each running a supported distribution. When I make a
change to the source base I suspect may break things I can
concurrently build from the same source on all the systems each
in their own subdirectory.
wget -c http://github.com/downloads/behlendorf/zfs/zfs-x.y.z.tar.gz
tar -xzf zfs-x.y.z.tar.gz
cd zfs-x-y-z
------------------------- run concurrently ----------------------
<ubuntu system> <fedora system> <debian system> <rhel6 system>
mkdir ubuntu mkdir fedora mkdir debian mkdir rhel6
cd ubuntu cd fedora cd debian cd rhel6
../configure ../configure ../configure ../configure
make make make make
make check make check make check make check
This change also moves many of the include headers from individual
incude/sys directories under the modules directory in to a single
top level include directory. This has the advantage of making
the build rules cleaner and logically it makes a bit more sense.
