If a pool was not cleanly exported passing the -f flag may be required
at 'zpool import' time. Since this test is simply validating that the
pool can be successfully imported in the absense of the cache file
always pass the -f to ensure it succeeds. This failure was observed
under RHEL6.1.
This change should have occured when we commited the new udev
rules for zvols. Basically, the test script is just out of date.
We need to update it to use the /dev/zvol/ device names, and
to expect the more common -partN suffixes.
I added a udev_trigger() call in zconfig_partition() and
zconfig_zvol_device_stat() to ensure that all the udev rules have
run before. This ensures the devices are available to subsequent
commands and closes a small race.
Finally, I was forced added a small 'sleep 1' to test 10. I
was observing occassional failures in my VM due to the device
still claiming to be busy. Delaying betwen the various methods
of adding/removing a vdev avoids the issue.
Closes#207
When adding this functionality originally the options to only
run specific tests (-t), or conversely skip specific tests (-s)
were omitted from the usage page. This commit adds the missing
documentation.
The idea behind the '-c' flag is to cleanup everything from a
previous test run which might cause the test script to fail.
This should also include removing the previously loaded module.
This makes it a little easier to run 'zconfig.sh -c', however
remember this is a test script and it will take all of your
other zpools offline for the purposes of the test. This notion
has also been extended to the default 'make check' behavior.
This test performs a sanity check of the zpool add and remove commands. It
tests adding and removing both a cache disk and a log disk to and from a zpool.
Usage of both a shorthand device path and a full path is covered. The test
uses a scsi_debug device as the disk to be added and removed. This is done so
that zpool will see it as a whole disk and partition it, which it does not
currently done for loopback devices. We want to verify that the manipulation
done to whole disks paths to hide the parition information does not break the
add/remove interface.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Eleven new zpool configurations were added to allow testing of various
failure cases. The first 5 zpool configurations leverage the 'faulty'
md device type which allow us to simuluate IO errors at the block layer.
The last 6 zpool configurations leverage the scsi_debug module provided
by modern kernels. This device allows you to create virtual scsi
devices which are backed by a ram disk. With this setup we can verify
the full IO stack by injecting faults at the lowest layer. Both methods
of fault injection are important to verifying the IO stack.
The zfs code itself also provides a mechanism for error injection
via the zinject command line tool. While we should also take advantage
of this appraoch to validate the code it does not address any of the
Linux integration issues which are the most concerning. For the
moment we're trusting that the upstream Solaris guys are running
zinject and would have caught internal zfs logic errors.
Currently, there are 6 r/w test cases layered on top of the 'faulty'
md devices. They include 3 writes tests for soft/transient errors,
hard/permenant errors, and all writes error to the device. There
are 3 matching read tests for soft/transient errors, hard/permenant
errors, and fixable read error with a write. Although for this last
case zfs doesn't do anything special.
The seventh test case verifies zfs detects and corrects checksum
errors. In this case one of the drives is extensively damaged and
by dd'ing over large sections of it. We then ensure zfs logs the
issue and correctly rebuilds the damage.
The next test cases use the scsi_debug configuration to injects error
at the bottom of the scsi stack. This ensures we find any flaws in the
scsi midlayer or our usage of it. Plus it stresses the device specific
retry, timeout, and error handling outside of zfs's control.
The eighth test case is to verify that the system correctly handles an
intermittent device timeout. Here the scsi_debug device drops 1 in N
requests resulting in a retry either at the block level. The ZFS code
does specify the FAILFAST option but it turns out that for this case
the Linux IO stack with still retry the command. The FAILFAST logic
located in scsi_noretry_cmd() does no seem to apply to the simply
timeout case. It appears to be more targeted to specific device or
transport errors from the lower layers.
The ninth test case handles a persistent failure in which the device
is removed from the system by Linux. The test verifies that the failure
is detected, the device is made unavailable, and then can be successfully
re-add when brought back online. Additionally, it ensures that errors
and events are logged to the correct places and the no data corruption
has occured due to the failure.
Occasional failures were observed in zconfig.sh because udev
could be delayed for a few seconds. To handle this the wait_udev
function has been added to wait for timeout seconds for an
expected device before returning an error. By default callers
currently use a 30 seconds timeout which should be much longer
than udev ever needs but not so long to worry the test suite
is hung.
This branch contains the majority of the changes required to cleanly
intergrate with Linux style special devices (/dev/zfs). Mainly this
means dropping all the Solaris style callbacks and replacing them
with the Linux equivilants.
This patch also adds the onexit infrastructure needed to track
some minimal state between ioctls. Under Linux it would be easy
to do this simply using the file->private_data. But under Solaris
they apparent need to pass the file descriptor as part of the ioctl
data and then perform a lookup in the kernel. Once again to keep
code change to a minimum I've implemented the Solaris solution.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Add autoconf style build infrastructure to the ZFS tree. This
includes autogen.sh, configure.ac, m4 macros, some scripts/*,
and makefiles for all the core ZFS components.
