mirror of
https://git.proxmox.com/git/mirror_zfs.git
synced 2024-11-18 10:21:01 +03:00
cf7c5a030e
14 Commits
| Author | SHA1 | Message | Date | |
|---|---|---|---|---|
Paul Dagnelie
|
c81f1790e2 |
Metaslab max_size should be persisted while unloaded
When we unload metaslabs today in ZFS, the cached max_size value is discarded. We instead use the histogram to determine whether or not we think we can satisfy an allocation from the metaslab. This can result in situations where, if we're doing I/Os of a size not aligned to a histogram bucket, a metaslab is loaded even though it cannot satisfy the allocation we think it can. For example, a metaslab with 16 entries in the 16k-32k bucket may have entirely 16kB entries. If we try to allocate a 24kB buffer, we will load that metaslab because we think it should be able to handle the allocation. Doing so is expensive in CPU time, disk reads, and average IO latency. This is exacerbated if the write being attempted is a sync write. This change makes ZFS cache the max_size after the metaslab is unloaded. If we ever get a free (or a coalesced group of frees) larger than the max_size, we will update it. Otherwise, we leave it as is. When attempting to allocate, we use the max_size as a lower bound, and respect it unless we are in try_hard. However, we do age the max_size out at some point, since we expect the actual max_size to increase as we do more frees. A more sophisticated algorithm here might be helpful, but this works reasonably well. Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov> Reviewed-by: Matt Ahrens <mahrens@delphix.com> Signed-off-by: Paul Dagnelie <pcd@delphix.com> Closes #9055 |
||
|
Serapheim Dimitropoulos
|
93e28d661e |
Log Spacemap Project
= Motivation At Delphix we've seen a lot of customer systems where fragmentation is over 75% and random writes take a performance hit because a lot of time is spend on I/Os that update on-disk space accounting metadata. Specifically, we seen cases where 20% to 40% of sync time is spend after sync pass 1 and ~30% of the I/Os on the system is spent updating spacemaps. The problem is that these pools have existed long enough that we've touched almost every metaslab at least once, and random writes scatter frees across all metaslabs every TXG, thus appending to their spacemaps and resulting in many I/Os. To give an example, assuming that every VDEV has 200 metaslabs and our writes fit within a single spacemap block (generally 4K) we have 200 I/Os. Then if we assume 2 levels of indirection, we need 400 additional I/Os and since we are talking about metadata for which we keep 2 extra copies for redundancy we need to triple that number, leading to a total of 1800 I/Os per VDEV every TXG. We could try and decrease the number of metaslabs so we have less I/Os per TXG but then each metaslab would cover a wider range on disk and thus would take more time to be loaded in memory from disk. In addition, after it's loaded, it's range tree would consume more memory. Another idea would be to just increase the spacemap block size which would allow us to fit more entries within an I/O block resulting in fewer I/Os per metaslab and a speedup in loading time. The problem is still that we don't deal with the number of I/Os going up as the number of metaslabs is increasing and the fact is that we generally write a lot to a few metaslabs and a little to the rest of them. Thus, just increasing the block size would actually waste bandwidth because we won't be utilizing our bigger block size. = About this patch This patch introduces the Log Spacemap project which provides the solution to the above problem while taking into account all the aforementioned tradeoffs. The details on how it achieves that can be found in the references sections below and in the code (see Big Theory Statement in spa_log_spacemap.c). Even though the change is fairly constraint within the metaslab and lower-level SPA codepaths, there is a side-change that is user-facing. The change is that VDEV IDs from VDEV holes will no longer be reused. To give some background and reasoning for this, when a log device is removed and its VDEV structure was replaced with a hole (or was compacted; if at the end of the vdev array), its vdev_id could be reused by devices added after that. Now with the pool-wide space maps recording the vdev ID, this behavior can cause problems (e.g. is this entry referring to a segment in the new vdev or the removed log?). Thus, to simplify things the ID reuse behavior is gone and now vdev IDs for top-level vdevs are truly unique within a pool. = Testing The illumos implementation of this feature has been used internally for a year and has been in production for ~6 months. For this patch specifically there don't seem to be any regressions introduced to ZTS and I have been running zloop for a week without any related problems. = Performance Analysis (Linux Specific) All performance results and analysis for illumos can be found in the links of the references. Redoing the same experiments in Linux gave similar results. Below are the specifics of the Linux run. After the pool reached stable state the percentage of the time spent in pass 1 per TXG was 64% on average for the stock bits while the log spacemap bits stayed at 95% during the experiment (graph: sdimitro.github.io/img/linux-lsm/PercOfSyncInPassOne.png). Sync times per TXG were 37.6 seconds on average for the stock bits and 22.7 seconds for the log spacemap bits (related graph: sdimitro.github.io/img/linux-lsm/SyncTimePerTXG.png). As a result the log spacemap bits were able to push more TXGs, which is also the reason why all graphs quantified per TXG have more entries for the log spacemap bits. Another interesting aspect in terms of txg syncs is that the stock bits had 22% of their TXGs reach sync pass 7, 55% reach sync pass 8, and 20% reach 9. The log space map bits reached sync pass 4 in 79% of their TXGs, sync pass 7 in 19%, and sync pass 8 at 1%. This emphasizes the fact that not only we spend less time on metadata but we also iterate less times to convergence in spa_sync() dirtying objects. [related graphs: stock- sdimitro.github.io/img/linux-lsm/NumberOfPassesPerTXGStock.png lsm- sdimitro.github.io/img/linux-lsm/NumberOfPassesPerTXGLSM.png] Finally, the improvement in IOPs that the userland gains from the change is approximately 40%. There is a consistent win in IOPS as you can see from the graphs below but the absolute amount of improvement that the log spacemap gives varies within each minute interval. sdimitro.github.io/img/linux-lsm/StockVsLog3Days.png sdimitro.github.io/img/linux-lsm/StockVsLog10Hours.png = Porting to Other Platforms For people that want to port this commit to other platforms below is a list of ZoL commits that this patch depends on: Make zdb results for checkpoint tests consistent |
||
|
Sara Hartse
|
a887d653b3 |
Restrict kstats and print real pointers
There are several places where we use zfs_dbgmsg and %p to print pointers. In the Linux kernel, these values obfuscated to prevent information leaks which means the pointers aren't very useful for debugging crash dumps. We decided to restrict the permissions of dbgmsg (and some other kstats while we were at it) and print pointers with %px in zfs_dbgmsg as well as spl_dumpstack Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov> Reviewed-by: John Gallagher <john.gallagher@delphix.com> Signed-off-by: sara hartse <sara.hartse@delphix.com> Closes #8467 Closes #8476 |
||
|
Serapheim Dimitropoulos
|
df72b8bebe |
Rename range_tree_verify to range_tree_verify_not_present
The range_tree_verify function looks for a segment in a range tree and panics if the segment is present on the tree. This patch gives the function a more descriptive name. Reviewed-by: Matt Ahrens <mahrens@delphix.com> Reviewed-by: George Melikov <mail@gmelikov.ru> Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov> Signed-off-by: Serapheim Dimitropoulos <serapheim@delphix.com> Closes #8327 |
||
|
Serapheim Dimitropoulos
|
d2734cce68 |
OpenZFS 9166 - zfs storage pool checkpoint
Details about the motivation of this feature and its usage can
be found in this blogpost:
https://sdimitro.github.io/post/zpool-checkpoint/
A lightning talk of this feature can be found here:
https://www.youtube.com/watch?v=fPQA8K40jAM
Implementation details can be found in big block comment of
spa_checkpoint.c
Side-changes that are relevant to this commit but not explained
elsewhere:
* renames members of "struct metaslab trees to be shorter without
losing meaning
* space_map_{alloc,truncate}() accept a block size as a
parameter. The reason is that in the current state all space
maps that we allocate through the DMU use a global tunable
(space_map_blksz) which defauls to 4KB. This is ok for metaslab
space maps in terms of bandwirdth since they are scattered all
over the disk. But for other space maps this default is probably
not what we want. Examples are device removal's vdev_obsolete_sm
or vdev_chedkpoint_sm from this review. Both of these have a
1:1 relationship with each vdev and could benefit from a bigger
block size.
Porting notes:
* The part of dsl_scan_sync() which handles async destroys has
been moved into the new dsl_process_async_destroys() function.
* Remove "VERIFY(!(flags & FWRITE))" in "kernel.c" so zhack can write
to block device backed pools.
* ZTS:
* Fix get_txg() in zpool_sync_001_pos due to "checkpoint_txg".
* Don't use large dd block sizes on /dev/urandom under Linux in
checkpoint_capacity.
* Adopt Delphix-OS's setting of 4 (spa_asize_inflation =
SPA_DVAS_PER_BP + 1) for the checkpoint_capacity test to speed
its attempts to fill the pool
* Create the base and nested pools with sync=disabled to speed up
the "setup" phase.
* Clear labels in test pool between checkpoint tests to avoid
duplicate pool issues.
* The import_rewind_device_replaced test has been marked as "known
to fail" for the reasons listed in its DISCLAIMER.
* New module parameters:
zfs_spa_discard_memory_limit,
zfs_remove_max_bytes_pause (not documented - debugging only)
vdev_max_ms_count (formerly metaslabs_per_vdev)
vdev_min_ms_count
Authored by: Serapheim Dimitropoulos <serapheim.dimitro@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Richard Lowe <richlowe@richlowe.net>
Ported-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Tim Chase <tim@chase2k.com>
OpenZFS-issue: https://illumos.org/issues/9166
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/7159fdb8
Closes #7570
|
||
|
Matthew Ahrens
|
0dc2f70c5c |
OpenZFS 9486 - reduce memory used by device removal on fragmented pools
Device removal allocates a new location for each allocated segment on
the disk that's being removed. Each allocation results in one entry in
the mapping table, which maps from old location + length to new
location. When a fragmented disk is removed, this can result in a large
number of mapping entries, and thus a large amount of memory consumed by
the mapping table. In the worst real-world cases, we've seen around 1GB
of RAM per 1TB of storage removed.
We can improve on this situation by allocating larger segments, which
span across both allocated and free regions of the device being removed.
By including free regions in the allocation (and thus mapping), we
reduce the number of mapping entries. For example, if we have a 4K
allocation followed by 1K free and then 4K allocated, we would allocate
4+1+4 = 9KB, and then move the entire region (including allocated and
free parts). In this case we used one mapping where previously we would
have used two, but often the ratio is much higher (up to 20:1 in
real-world use). We then need to mark the regions that were free on the
removing device as free in the new locations, and also obsolete in the
mapping entry.
This method preserves the fragmentation of the removing device, rather
than consolidating its allocated space into a small number of chunks
where possible. But it results in drastic reduction of memory used by
the mapping table - around 20x in the most-fragmented cases.
In the most fragmented real-world cases, this reduces memory used by the
mapping from ~1GB to ~50MB of RAM per 1TB of storage removed. Less
fragmented cases will typically also see around 50-100MB of RAM per 1TB
of storage.
Porting notes:
* Add the following as module parameters:
* zfs_condense_indirect_vdevs_enable
* zfs_condense_max_obsolete_bytes
* Document the following module parameters:
* zfs_condense_indirect_vdevs_enable
* zfs_condense_max_obsolete_bytes
* zfs_condense_min_mapping_bytes
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Tim Chase <tim@chase2k.com>
OpenZFS-issue: https://illumos.org/issues/9486
OpenZFS-commit: https://github.com/ahrens/illumos/commit/07152e142e44c
External-issue: DLPX-57962
Closes #7536
|
||
|
Matthew Ahrens
|
a1d477c24c |
OpenZFS 7614, 9064 - zfs device evacuation/removal
OpenZFS 7614 - zfs device evacuation/removal
OpenZFS 9064 - remove_mirror should wait for device removal to complete
This project allows top-level vdevs to be removed from the storage pool
with "zpool remove", reducing the total amount of storage in the pool.
This operation copies all allocated regions of the device to be removed
onto other devices, recording the mapping from old to new location.
After the removal is complete, read and free operations to the removed
(now "indirect") vdev must be remapped and performed at the new location
on disk. The indirect mapping table is kept in memory whenever the pool
is loaded, so there is minimal performance overhead when doing operations
on the indirect vdev.
The size of the in-memory mapping table will be reduced when its entries
become "obsolete" because they are no longer used by any block pointers
in the pool. An entry becomes obsolete when all the blocks that use
it are freed. An entry can also become obsolete when all the snapshots
that reference it are deleted, and the block pointers that reference it
have been "remapped" in all filesystems/zvols (and clones). Whenever an
indirect block is written, all the block pointers in it will be "remapped"
to their new (concrete) locations if possible. This process can be
accelerated by using the "zfs remap" command to proactively rewrite all
indirect blocks that reference indirect (removed) vdevs.
Note that when a device is removed, we do not verify the checksum of
the data that is copied. This makes the process much faster, but if it
were used on redundant vdevs (i.e. mirror or raidz vdevs), it would be
possible to copy the wrong data, when we have the correct data on e.g.
the other side of the mirror.
At the moment, only mirrors and simple top-level vdevs can be removed
and no removal is allowed if any of the top-level vdevs are raidz.
Porting Notes:
* Avoid zero-sized kmem_alloc() in vdev_compact_children().
The device evacuation code adds a dependency that
vdev_compact_children() be able to properly empty the vdev_child
array by setting it to NULL and zeroing vdev_children. Under Linux,
kmem_alloc() and related functions return a sentinel pointer rather
than NULL for zero-sized allocations.
* Remove comment regarding "mpt" driver where zfs_remove_max_segment
is initialized to SPA_MAXBLOCKSIZE.
Change zfs_condense_indirect_commit_entry_delay_ticks to
zfs_condense_indirect_commit_entry_delay_ms for consistency with
most other tunables in which delays are specified in ms.
* ZTS changes:
Use set_tunable rather than mdb
Use zpool sync as appropriate
Use sync_pool instead of sync
Kill jobs during test_removal_with_operation to allow unmount/export
Don't add non-disk names such as "mirror" or "raidz" to $DISKS
Use $TEST_BASE_DIR instead of /tmp
Increase HZ from 100 to 1000 which is more common on Linux
removal_multiple_indirection.ksh
Reduce iterations in order to not time out on the code
coverage builders.
removal_resume_export:
Functionally, the test case is correct but there exists a race
where the kernel thread hasn't been fully started yet and is
not visible. Wait for up to 1 second for the removal thread
to be started before giving up on it. Also, increase the
amount of data copied in order that the removal not finish
before the export has a chance to fail.
* MMP compatibility, the concept of concrete versus non-concrete devices
has slightly changed the semantics of vdev_writeable(). Update
mmp_random_leaf_impl() accordingly.
* Updated dbuf_remap() to handle the org.zfsonlinux:large_dnode pool
feature which is not supported by OpenZFS.
* Added support for new vdev removal tracepoints.
* Test cases removal_with_zdb and removal_condense_export have been
intentionally disabled. When run manually they pass as intended,
but when running in the automated test environment they produce
unreliable results on the latest Fedora release.
They may work better once the upstream pool import refectoring is
merged into ZoL at which point they will be re-enabled.
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Alex Reece <alex@delphix.com>
Reviewed-by: George Wilson <george.wilson@delphix.com>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: Richard Laager <rlaager@wiktel.com>
Reviewed by: Tim Chase <tim@chase2k.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Garrett D'Amore <garrett@damore.org>
Ported-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Tim Chase <tim@chase2k.com>
OpenZFS-issue: https://www.illumos.org/issues/7614
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/f539f1eb
Closes #6900
|
||
|
Tom Caputi
|
d4a72f2386 |
Sequential scrub and resilvers
Currently, scrubs and resilvers can take an extremely long time to complete. This is largely due to the fact that zfs scans process pools in logical order, as determined by each block's bookmark. This makes sense from a simplicity perspective, but blocks in zfs are often scattered randomly across disks, particularly due to zfs's copy-on-write mechanisms. This patch improves performance by splitting scrubs and resilvers into a metadata scanning phase and an IO issuing phase. The metadata scan reads through the structure of the pool and gathers an in-memory queue of I/Os, sorted by size and offset on disk. The issuing phase will then issue the scrub I/Os as sequentially as possible, greatly improving performance. This patch also updates and cleans up some of the scan code which has not been updated in several years. Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov> Authored-by: Saso Kiselkov <saso.kiselkov@nexenta.com> Authored-by: Alek Pinchuk <apinchuk@datto.com> Authored-by: Tom Caputi <tcaputi@datto.com> Signed-off-by: Tom Caputi <tcaputi@datto.com> Closes #3625 Closes #6256 |
||
|
Gvozden Neskovic
|
ee36c709c3 |
Performance optimization of AVL tree comparator functions
perf: 2.75x faster ddt_entry_compare()
First 256bits of ddt_key_t is a block checksum, which are expected
to be close to random data. Hence, on average, comparison only needs to
look at first few bytes of the keys. To reduce number of conditional
jump instructions, the result is computed as: sign(memcmp(k1, k2)).
Sign of an integer 'a' can be obtained as: `(0 < a) - (a < 0)` := {-1, 0, 1} ,
which is computed efficiently. Synthetic performance evaluation of
original and new algorithm over 1G random keys on 2.6GHz Intel(R) Xeon(R)
CPU E5-2660 v3:
old 6.85789 s
new 2.49089 s
perf: 2.8x faster vdev_queue_offset_compare() and vdev_queue_timestamp_compare()
Compute the result directly instead of using conditionals
perf: zfs_range_compare()
Speedup between 1.1x - 2.5x, depending on compiler version and
optimization level.
perf: spa_error_entry_compare()
`bcmp()` is not suitable for comparator use. Use `memcmp()` instead.
perf: 2.8x faster metaslab_compare() and metaslab_rangesize_compare()
perf: 2.8x faster zil_bp_compare()
perf: 2.8x faster mze_compare()
perf: faster dbuf_compare()
perf: faster compares in spa_misc
perf: 2.8x faster layout_hash_compare()
perf: 2.8x faster space_reftree_compare()
perf: libzfs: faster avl tree comparators
perf: guid_compare()
perf: dsl_deadlist_compare()
perf: perm_set_compare()
perf: 2x faster range_tree_seg_compare()
perf: faster unique_compare()
perf: faster vdev_cache _compare()
perf: faster vdev_uberblock_compare()
perf: faster fuid _compare()
perf: faster zfs_znode_hold_compare()
Signed-off-by: Gvozden Neskovic <neskovic@gmail.com>
Signed-off-by: Richard Elling <richard.elling@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #5033
|
||
|
George Wilson
|
669dedb33f |
Illumos 5163 - arc should reap range_seg_cache
5163 arc should reap range_seg_cache Reviewed by: Christopher Siden <christopher.siden@delphix.com> Reviewed by: Matthew Ahrens <mahrens@delphix.com> Reviewed by: Richard Elling <richard.elling@gmail.com> Reviewed by: Saso Kiselkov <skiselkov.ml@gmail.com> Approved by: Dan McDonald <danmcd@omniti.com> References: https://www.illumos.org/issues/5163 https://github.com/illumos/illumos-gate/commit/83803b5 Porting Notes: Added umem_cache_reap_now() wrapped to suppress unused variable warning for user space build in arc_kmem_reap_now(). Ported-by: Brian Behlendorf <behlendorf1@llnl.gov> |
||
|
Brian Behlendorf
|
79c76d5b65 |
Change KM_PUSHPAGE -> KM_SLEEP
By marking DMU transaction processing contexts with PF_FSTRANS we can revert the KM_PUSHPAGE -> KM_SLEEP changes. This brings us back in line with upstream. In some cases this means simply swapping the flags back. For others fnvlist_alloc() was replaced by nvlist_alloc(..., KM_PUSHPAGE) and must be reverted back to fnvlist_alloc() which assumes KM_SLEEP. The one place KM_PUSHPAGE is kept is when allocating ARC buffers which allows us to dip in to reserved memory. This is again the same as upstream. Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov> |
||
|
George Wilson
|
f3a7f6610f |
Illumos 4976-4984 - metaslab improvements
4976 zfs should only avoid writing to a failing non-redundant top-level vdev 4978 ztest fails in get_metaslab_refcount() 4979 extend free space histogram to device and pool 4980 metaslabs should have a fragmentation metric 4981 remove fragmented ops vector from block allocator 4982 space_map object should proactively upgrade when feature is enabled 4983 need to collect metaslab information via mdb 4984 device selection should use fragmentation metric Reviewed by: Matthew Ahrens <mahrens@delphix.com> Reviewed by: Adam Leventhal <adam.leventhal@delphix.com> Reviewed by: Christopher Siden <christopher.siden@delphix.com> Approved by: Garrett D'Amore <garrett@damore.org> References: https://www.illumos.org/issues/4976 https://www.illumos.org/issues/4978 https://www.illumos.org/issues/4979 https://www.illumos.org/issues/4980 https://www.illumos.org/issues/4981 https://www.illumos.org/issues/4982 https://www.illumos.org/issues/4983 https://www.illumos.org/issues/4984 https://github.com/illumos/illumos-gate/commit/2e4c998 Notes: The "zdb -M" option has been re-tasked to display the new metaslab fragmentation metric and the new "zdb -I" option is used to control the maximum number of in-flight I/Os. The new fragmentation metric is derived from the space map histogram which has been rolled up to the vdev and pool level and is presented to the user via "zpool list". Add a number of module parameters related to the new metaslab weighting logic. Ported by: Tim Chase <tim@chase2k.com> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov> Closes #2595 |
||
|
Matthew Ahrens
|
9bd274ddd8 |
Illumos #4374
4374 dn_free_ranges should use range_tree_t Reviewed by: George Wilson <george.wilson@delphix.com> Reviewed by: Max Grossman <max.grossman@delphix.com> Reviewed by: Christopher Siden <christopher.siden@delphix.com Reviewed by: Garrett D'Amore <garrett@damore.org> Reviewed by: Dan McDonald <danmcd@omniti.com> Approved by: Dan McDonald <danmcd@omniti.com> References: https://www.illumos.org/issues/4374 https://github.com/illumos/illumos-gate/commit/bf16b11 Ported by: Tim Chase <tim@chase2k.com> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov> Closes #2531 |
||
|
George Wilson
|
93cf20764a |
Illumos #4101, #4102, #4103, #4105, #4106
4101 metaslab_debug should allow for fine-grained control
4102 space_maps should store more information about themselves
4103 space map object blocksize should be increased
4105 removing a mirrored log device results in a leaked object
4106 asynchronously load metaslab
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Adam Leventhal <ahl@delphix.com>
Reviewed by: Sebastien Roy <seb@delphix.com>
Approved by: Garrett D'Amore <garrett@damore.org>
Prior to this patch, space_maps were preferred solely based on the
amount of free space left in each. Unfortunately, this heuristic didn't
contain any information about the make-up of that free space, which
meant we could keep preferring and loading a highly fragmented space map
that wouldn't actually have enough contiguous space to satisfy the
allocation; then unloading that space_map and repeating the process.
This change modifies the space_map's to store additional information
about the contiguous space in the space_map, so that we can use this
information to make a better decision about which space_map to load.
This requires reallocating all space_map objects to increase their
bonus buffer size sizes enough to fit the new metadata.
The above feature can be enabled via a new feature flag introduced by
this change: com.delphix:spacemap_histogram
In addition to the above, this patch allows the space_map block size to
be increase. Currently the block size is set to be 4K in size, which has
certain implications including the following:
* 4K sector devices will not see any compression benefit
* large space_maps require more metadata on-disk
* large space_maps require more time to load (typically random reads)
Now the space_map block size can adjust as needed up to the maximum size
set via the space_map_max_blksz variable.
A bug was fixed which resulted in potentially leaking an object when
removing a mirrored log device. The previous logic for vdev_remove() did
not deal with removing top-level vdevs that are interior vdevs (i.e.
mirror) correctly. The problem would occur when removing a mirrored log
device, and result in the DTL space map object being leaked; because
top-level vdevs don't have DTL space map objects associated with them.
References:
https://www.illumos.org/issues/4101
https://www.illumos.org/issues/4102
https://www.illumos.org/issues/4103
https://www.illumos.org/issues/4105
https://www.illumos.org/issues/4106
https://github.com/illumos/illumos-gate/commit/0713e23
Porting notes:
A handful of kmem_alloc() calls were converted to kmem_zalloc(). Also,
the KM_PUSHPAGE and TQ_PUSHPAGE flags were used as necessary.
Ported-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Prakash Surya <surya1@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #2488
|