Adding O_DIRECT support to ZFS to bypass the ARC for writes/reads.
O_DIRECT support in ZFS will always ensure there is coherency between
buffered and O_DIRECT IO requests. This ensures that all IO requests,
whether buffered or direct, will see the same file contents at all
times. Just as in other FS's , O_DIRECT does not imply O_SYNC. While
data is written directly to VDEV disks, metadata will not be synced
until the associated TXG is synced.
For both O_DIRECT read and write request the offset and request sizes,
at a minimum, must be PAGE_SIZE aligned. In the event they are not,
then EINVAL is returned unless the direct property is set to always (see
below).
For O_DIRECT writes:
The request also must be block aligned (recordsize) or the write
request will take the normal (buffered) write path. In the event that
request is block aligned and a cached copy of the buffer in the ARC,
then it will be discarded from the ARC forcing all further reads to
retrieve the data from disk.
For O_DIRECT reads:
The only alignment restrictions are PAGE_SIZE alignment. In the event
that the requested data is in buffered (in the ARC) it will just be
copied from the ARC into the user buffer.
For both O_DIRECT writes and reads the O_DIRECT flag will be ignored in
the event that file contents are mmap'ed. In this case, all requests
that are at least PAGE_SIZE aligned will just fall back to the buffered
paths. If the request however is not PAGE_SIZE aligned, EINVAL will
be returned as always regardless if the file's contents are mmap'ed.
Since O_DIRECT writes go through the normal ZIO pipeline, the
following operations are supported just as with normal buffered writes:
Checksum
Compression
Encryption
Erasure Coding
There is one caveat for the data integrity of O_DIRECT writes that is
distinct for each of the OS's supported by ZFS.
FreeBSD - FreeBSD is able to place user pages under write protection so
any data in the user buffers and written directly down to the
VDEV disks is guaranteed to not change. There is no concern
with data integrity and O_DIRECT writes.
Linux - Linux is not able to place anonymous user pages under write
protection. Because of this, if the user decides to manipulate
the page contents while the write operation is occurring, data
integrity can not be guaranteed. However, there is a module
parameter `zfs_vdev_direct_write_verify` that controls the
if a O_DIRECT writes that can occur to a top-level VDEV before
a checksum verify is run before the contents of the I/O buffer
are committed to disk. In the event of a checksum verification
failure the write will return EIO. The number of O_DIRECT write
checksum verification errors can be observed by doing
`zpool status -d`, which will list all verification errors that
have occurred on a top-level VDEV. Along with `zpool status`, a
ZED event will be issues as `dio_verify` when a checksum
verification error occurs.
ZVOLs and dedup is not currently supported with Direct I/O.
A new dataset property `direct` has been added with the following 3
allowable values:
disabled - Accepts O_DIRECT flag, but silently ignores it and treats
the request as a buffered IO request.
standard - Follows the alignment restrictions outlined above for
write/read IO requests when the O_DIRECT flag is used.
always - Treats every write/read IO request as though it passed
O_DIRECT and will do O_DIRECT if the alignment restrictions
are met otherwise will redirect through the ARC. This
property will not allow a request to fail.
There is also a module parameter zfs_dio_enabled that can be used to
force all reads and writes through the ARC. By setting this module
parameter to 0, it mimics as if the direct dataset property is set to
disabled.
Reviewed-by: Brian Behlendorf <behlendorf@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Atkinson <batkinson@lanl.gov>
Co-authored-by: Mark Maybee <mark.maybee@delphix.com>
Co-authored-by: Matt Macy <mmacy@FreeBSD.org>
Co-authored-by: Brian Behlendorf <behlendorf@llnl.gov>
Closes#10018
Sponsored-by: Klara, Inc.
Sponsored-By: Wasabi Technology, Inc.
Signed-off-by: Don Brady <don.brady@klarasystems.com>
Co-authored-by: Don Brady <don.brady@klarasystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
After c3f2f1aa2, vdev_fault_wanted is set on a vdev after a probe fails.
An end-of-txg async task is charged with actually faulting the vdev.
In a single-disk pool, the probe failure will degrade the last disk, and
then suspend the pool. However, vdev_fault_wanted is not cleared. After
the pool returns, the transaction finishes and the async task runs and
faults the vdev, which suspends the pool again.
The fix is simple: when reopening a vdev, clear the async fault flag. If
the vdev is still failed, the startup probe will quickly notice and
degrade/suspend it again. If not, all is well!
Sponsored-by: Klara, Inc.
Sponsored-by: Wasabi Technology, Inc.
Co-authored-by: Don Brady <don.brady@klarasystems.com>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Don Brady <don.brady@klarasystems.com>
Optionally turn off disk's enclosure slot if an I/O is hung
triggering the deadman.
It's possible for outstanding I/O to a misbehaving SCSI disk to
neither promptly complete or return an error. This can occur due
to retry and recovery actions taken by the SCSI layer, driver, or
disk. When it occurs the pool will be unresponsive even though
there may be sufficient redundancy configured to proceeded without
this single disk.
When a hung I/O is detected by the kmods it will be posted as a
deadman event. By default an I/O is considered to be hung after
5 minutes. This value can be changed with the zfs_deadman_ziotime_ms
module parameter. If ZED_POWER_OFF_ENCLOSURE_SLOT_ON_DEADMAN is set
the disk's enclosure slot will be powered off causing the outstanding
I/O to fail. The ZED will then handle this like a normal disk failure.
By default ZED_POWER_OFF_ENCLOSURE_SLOT_ON_DEADMAN is not set.
As part of this change `zfs_deadman_events_per_second` is added
to control the ratelimitting of deadman events independantly of
delay events. In practice, a single deadman event is sufficient
and more aren't particularly useful.
Alphabetize the zfs_deadman_* entries in zfs.4.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#16226
In P2ALIGN, the result would be incorrect when align is unsigned
integer and x is larger than max value of the type of align.
In that case, -(align) would be a positive integer, which means
high bits would be zero and finally stay zero after '&' when
align is converted to a larger integer type.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Youzhong Yang <yyang@mathworks.com>
Signed-off-by: Qiuhao Chen <chenqiuhao1997@gmail.com>
Closes#15940
Simplify vdev probes in the zio_vdev_io_done context to
avoid holding the spa config lock for a long duration.
Also allow zpool clear if no evidence of another host
is using the pool.
Sponsored-by: Klara, Inc.
Sponsored-by: Wasabi Technology, Inc.
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@klarasystems.com>
Closes#15839
The only possible ioctl is a flush, and any other kind of meta-operation
introduced in the future is likely to have different semantics (much
like trim did). So, lets just call it what it is.
Sponsored-by: Klara, Inc.
Sponsored-by: Wasabi Technology, Inc.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Closes#16064
Slow disk response times can be indicative of a failing drive. ZFS
currently tracks slow I/Os (slower than zio_slow_io_ms) and generates
events (ereport.fs.zfs.delay). However, no action is taken by ZED,
like is done for checksum or I/O errors. This change adds slow disk
diagnosis to ZED which is opt-in using new VDEV properties:
VDEV_PROP_SLOW_IO_N
VDEV_PROP_SLOW_IO_T
If multiple VDEVs in a pool are undergoing slow I/Os, then it skips
the zpool_vdev_degrade().
Sponsored-By: OpenDrives Inc.
Sponsored-By: Klara Inc.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Rob Wing <rob.wing@klarasystems.com>
Signed-off-by: Don Brady <don.brady@klarasystems.com>
Closes#15469
If devid or physpath for a vdev changes between imports, ensure it is
updated to the new value.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#15816
This feature allows disks to be added one at a time to a RAID-Z group,
expanding its capacity incrementally. This feature is especially useful
for small pools (typically with only one RAID-Z group), where there
isn't sufficient hardware to add capacity by adding a whole new RAID-Z
group (typically doubling the number of disks).
== Initiating expansion ==
A new device (disk) can be attached to an existing RAIDZ vdev, by
running `zpool attach POOL raidzP-N NEW_DEVICE`, e.g. `zpool attach tank
raidz2-0 sda`. The new device will become part of the RAIDZ group. A
"raidz expansion" will be initiated, and the new device will contribute
additional space to the RAIDZ group once the expansion completes.
The `feature@raidz_expansion` on-disk feature flag must be `enabled` to
initiate an expansion, and it remains `active` for the life of the pool.
In other words, pools with expanded RAIDZ vdevs can not be imported by
older releases of the ZFS software.
== During expansion ==
The expansion entails reading all allocated space from existing disks in
the RAIDZ group, and rewriting it to the new disks in the RAIDZ group
(including the newly added device).
The expansion progress can be monitored with `zpool status`.
Data redundancy is maintained during (and after) the expansion. If a
disk fails while the expansion is in progress, the expansion pauses
until the health of the RAIDZ vdev is restored (e.g. by replacing the
failed disk and waiting for reconstruction to complete).
The pool remains accessible during expansion. Following a reboot or
export/import, the expansion resumes where it left off.
== After expansion ==
When the expansion completes, the additional space is available for use,
and is reflected in the `available` zfs property (as seen in `zfs list`,
`df`, etc).
Expansion does not change the number of failures that can be tolerated
without data loss (e.g. a RAIDZ2 is still a RAIDZ2 even after
expansion).
A RAIDZ vdev can be expanded multiple times.
After the expansion completes, old blocks remain with their old
data-to-parity ratio (e.g. 5-wide RAIDZ2, has 3 data to 2 parity), but
distributed among the larger set of disks. New blocks will be written
with the new data-to-parity ratio (e.g. a 5-wide RAIDZ2 which has been
expanded once to 6-wide, has 4 data to 2 parity). However, the RAIDZ
vdev's "assumed parity ratio" does not change, so slightly less space
than is expected may be reported for newly-written blocks, according to
`zfs list`, `df`, `ls -s`, and similar tools.
Sponsored-by: The FreeBSD Foundation
Sponsored-by: iXsystems, Inc.
Sponsored-by: vStack
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Authored-by: Matthew Ahrens <mahrens@delphix.com>
Contributions-by: Fedor Uporov <fuporov.vstack@gmail.com>
Contributions-by: Stuart Maybee <stuart.maybee@comcast.net>
Contributions-by: Thorsten Behrens <tbehrens@outlook.com>
Contributions-by: Fmstrat <nospam@nowsci.com>
Contributions-by: Don Brady <dev.fs.zfs@gmail.com>
Signed-off-by: Don Brady <dev.fs.zfs@gmail.com>
Closes#15022
When a vdev is to be expanded -- either via `zpool online -e` or via
the autoexpand option -- a SPA_ASYNC_CONFIG_UPDATE request is queued
to be handled via an asynchronous worker thread (spa_async_thread).
This normally happens almost immediately; but will be delayed up to
zfs_ccw_retry_interval seconds (default 5 minutes) if an attempt to
write the zpool configuration cache failed.
When FreeBSD boots ZFS-root VM images generated using `makefs -t zfs`,
the zpoolupgrade rc.d script runs `zpool upgrade`, which modifies the
pool configuration and triggers an attempt to write to the cache file.
This attempted write fails because the filesystem is still mounted
read-only at this point in the boot process, triggering a 5-minute
cooldown before SPA_ASYNC_CONFIG_UPDATE requests will be handled by
the asynchronous worker thread.
When expanding a vdev, reset the "when did a configuration cache
write last fail" value so that the SPA_ASYNC_CONFIG_UPDATE request
will be handled promptly. A cleaner but more intrusive option would
be to use separate SPA_ASYNC_ flags for "configuration changed" and
"try writing the configuration cache again", but with FreeBSD 14.0
coming very soon I'd prefer to leave such refactoring for a later
date.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Colin Percival <cperciva@FreeBSD.org>
Closes#15405
Fastwrite was introduced many years ago to improve ZIL writes spread
between multiple top-level vdevs by tracking number of allocated but
not written blocks and choosing vdev with smaller count. It suposed
to reduce ZIL knowledge about allocation, but actually made ZIL to
even more actively report allocation code about the allocations,
complicating both ZIL and metaslabs code.
On top of that, it seems ZIO_FLAG_FASTWRITE setting in dmu_sync()
was lost many years ago, that was one of the declared benefits. Plus
introduction of embedded log metaslab class solved another problem
with allocation rotor accounting both normal and log allocations,
since in most cases those are now in different metaslab classes.
After all that, I'd prefer to simplify already too complicated ZIL,
ZIO and metaslab code if the benefit of complexity is not obvious.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Wilson <george.wilson@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#15107
Since spa_min_alloc may not be a power of 2, unlike ashifts, in the
case of DRAID, we should not select the minimal value among several
vdevs. Rounding to a multiple of it is unlikely to work for other
vdevs. Instead, using the greatest common divisor produces smaller
yet more reasonable results.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#15067
Check that vdev has valid zap and bail out early.
While here, move objid selection out of the loop, it's not going to
change.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Yuri Pankov <yuripv@FreeBSD.org>
Closes#15063
Ashift can be set for a vdev only during its creation, and the
top-level vdev does not change when a vdev is attached or replaced.
The ashift property should not be used during attachment, as it
does not allow attaching/replacing a vdev if the pool's ashift
property is increased after the existing vdev was created. Instead,
we should be able to attach the vdev if the attached vdev can
satisfy the ashift requirement with its parent.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#15061
Switch FIFO queues (SYNC/TRIM) and active queue of vdev queue from
time-sorted AVL-trees to simple lists. AVL-trees are too expensive
for such a simple task. To change I/O priority without searching
through the trees, add io_queue_state field to struct zio.
To not check number of queued I/Os for each priority add vq_cqueued
bitmap to struct vdev_queue. Update it when adding/removing I/Os.
Make vq_cactive a separate array instead of struct vdev_queue_class
member. Together those allow to avoid lots of cache misses when
looking for work in vdev_queue_class_to_issue().
Introduce deadline of ~0.5s for LBA-sorted queues. Before this I
saw some I/Os waiting in a queue for up to 8 seconds and possibly
more due to starvation. With this change I no longer see it. I
had to slightly more complicate the comparison function, but since
it uses all the same cache lines the difference is minimal. For a
sequential I/Os the new code in vdev_queue_io_to_issue() actually
often uses more simple avl_first(), falling back to avl_find() and
avl_nearest() only when needed.
Arrange members in struct zio to access only one cache line when
searching through vdev queues. While there, remove io_alloc_node,
reusing the io_queue_node instead. Those two are never used same
time.
Remove zfs_vdev_aggregate_trim parameter. It was disabled for 4
years since implemented, while still wasted time maintaining the
offset-sorted tree of TRIM requests. Just remove the tree.
Remove locking from txg_all_lists_empty(). It is racy by design,
while 2 pair of locks/unlocks take noticeable time under the vdev
queue lock.
With these changes in my tests with volblocksize=4KB I measure vdev
queue lock spin time reduction by 50% on read and 75% on write.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14925
It was a vdev level read cache, designed to aggregate many small
reads by speculatively issuing bigger reads instead and caching
the result. But since it has almost no idea about what is going
on with exception of ZIO_FLAG_DONT_CACHE flag set by higher layers,
it was found to make more harm than good, for which reason it was
disabled for the past 12 years. These days we have much better
instruments to enlarge the I/Os, such as speculative and prescient
prefetches, I/O scheduler, I/O aggregation etc.
Besides just the dead code removal this removes one extra mutex
lock/unlock per write inside vdev_cache_write(), not otherwise
disabled and trying to do some work.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14953
For draid vdevs it was possible to initiate both the
sequential and healing resilver at same time.
This fixes the following two scenarios.
1) There's a window where a sequential rebuild can
be started via ZED even if a healing resilver has been
scheduled.
- This is fixed by adding additional check in
spa_vdev_attach() for any scheduled resilver and return
appropriate error code when a resilver is already in
progress.
2) It was possible for zpool clear to start a healing
resilver when it wasn't needed at all. This occurs because
during a vdev_open() the device is presumed to be healthy not
until the device is validated by vdev_validate() and it's set
unavailable. However, by this point an async resilver will
have already been requested if the DTL isn't empty.
- This is fixed by cancelling the SPA_ASYNC_RESILVER
request immediately at the end of vdev_reopen() when a resilver
is unneeded.
Finally, added a testcase in ZTS for verification.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Dipak Ghosh <dipak.ghosh@hpe.com>
Signed-off-by: Akash B <akash-b@hpe.com>
Closes#14881Closes#14892
Before allowing the ZED to mark a vdev as REMOVED due to a
hotplug event confirm that it is non-responsive with probe.
Any device which can be successfully probed should be left
ONLINE to prevent a healthy pool from being incorrectly
SUSPENDED. This may occur for at least the following two
scenarios.
1) Drive expansion (zpool online -e) in VMware environments.
If, during the partition resize operation, a partition is
removed and re-created then udev will send a removed event.
2) Re-scanning the namespaces of an NVMe device (nvme ns-rescan)
may result in a udev remove and add event being delivered.
Finally, update the ZED to only kick in a spare when the
removal was successful.
Reviewed-by: Ameer Hamza <ahamza@ixsystems.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #14859Closes#14861
And add it to the AVZ, this is not backwards compatible with older pools
due to an assertion in spa_sync() that verifies the number of ZAPs of
all vdevs matches the number of ZAPs in the AVZ.
Granted, the assertion only applies to #DEBUG builds - still, a feature
flag is introduced to avoid the assertion, com.klarasystems:vdev_zaps_v2
Notably, this allows to get/set properties on the root vdev:
% zpool set user:prop=value <pool> root-0
Before this commit, it was already possible to get/set properties on
top-level vdevs with the syntax <type>-<vdev_id> (e.g. mirror-0):
% zpool set user:prop=value <pool> mirror-0
This syntax also applies to the root vdev as it is is of type 'root'
with a vdev_id of 0, root-0. The keyword 'root' as an alias for
'root-0'.
The following tests have been added:
- zpool get all properties from root vdev
- zpool set a property on root vdev
- verify root vdev ZAP is created
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Wing <rob.wing@klarasystems.com>
Sponsored-by: Seagate Technology
Submitted-by: Klara, Inc.
Closes#14405
Spare vdev should detach from the pool when a disk is reinserted.
However, spare detachment depends on the completion of resilvering,
and if resilver does not schedule, the spare vdev keeps attached to
the pool until the next resilvering. When a zfs pool contains
several disks (25+ mirror), resilvering does not always happen when
a disk is reinserted. In this patch, spare vdev is manually detached
from the pool when resilvering does not occur and it has been tested
on both Linux and FreeBSD.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#14722
Current autotrim causes short-lived txg through:
1. calling txg_wait_synced() in metaslab_enable()
2. calling txg_wait_open() with should_quiesce = true
This patch addresses all the issues mentioned above.
A new cv, vdev_autotrim_kick_cv is added to kick autotrim activity.
It will be signaled once a txg is synced so that it does not change
the original autotrim pace. Also because it is a cv, the wait is
interruptible which speeds up the vdev_autotrim_stop_wait() call.
Finally, combining big zfs_txg_timeout, txg_wait_open() also causes
delay when exporting a pool.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: jxdking <lostking2008@hotmail.com>
Issue #8993Closes#12194
After addressing coverity complaints involving `nvpair_name()`, the
compiler started complaining about dropping const. This lead to a rabbit
hole where not only `nvpair_name()` needed to be constified, but also
`nvpair_value_string()`, `fnvpair_value_string()` and a few other static
functions, plus variable pointers throughout the code. The result became
a fairly big change, so it has been split out into its own patch.
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14612
63652e1546 added unnecessary branches in
`vdev_stat_update()` to suppress an ASAN false positive the breaks
ztest. This had the downside of causing false positive reports in both
Coverity and Clang's static analyzer. vd is never NULL, so we add a
preprocessor check to only apply the workaround when compiling with ASAN
support.
Reported-by: Coverity (CID-1524583)
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14575
Clang's static analyzer pointed out that we can have a NULL pointer
dereference if we ever attempt to split a vdev that has only 1 child. If
that happens, we are left with zero children, but then try to access a
non-existent child. Calling vdev_split() on a vdev with only 1 child
should be impossible due to how the code is structured. If this ever
happens, it would be best to stop execution immediately even in a
production environment to allow for the best possible chance of recovery
by an expert, so we use `VERIFY3U()` instead of `ASSERT3U()`.
Unfortunately, while that defensive assertion will prevent execution
from ever reaching the NULL pointer dereference, Clang's static analyzer
does not realize that, so we add an `ASSERT()` to inform it of this.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14575
Introduce four new vdev properties:
checksum_n
checksum_t
io_n
io_t
These properties can be used for configuring the thresholds of zed's
diagnosis engine and are interpeted as <N> events in T <seconds>.
When this property is set to a non-default value on a top-level vdev,
those thresholds will also apply to its leaf vdevs. This behavior can be
overridden by explicitly setting the property on the leaf vdev.
Note that, these properties do not persist across vdev replacement. For
this reason, it is advisable to set the property on the top-level vdev
instead of the leaf vdev.
The default values for zed's diagnosis engine (10 events, 600 seconds)
remains unchanged.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Rob Wing <rob.wing@klarasystems.com>
Sponsored-by: Seagate Technology LLC
Closes#13805
If the attached disk already contains a vdev GUID, it
means the disk is not clean. In such a scenario, the
physical path would be a match that makes the disk
faulted when trying to online it. So, we would only
want to proceed if either GUID matches with the last
attached disk or the disk is in a clean state.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#14181
Linux defaults to setting "failfast" on BIOs, so that the OS will not
retry IOs that fail, and instead report the error to ZFS.
In some cases, such as errors reported by the HBA driver, not
the device itself, we would wish to retry rather than generating
vdev errors in ZFS. This new property allows that.
This introduces a per vdev option to disable the failfast option.
This also introduces a global module parameter to define the failfast
mask value.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Mariusz Zaborski <mariusz.zaborski@klarasystems.com>
Sponsored-by: Seagate Technology LLC
Submitted-by: Klara, Inc.
Closes#14056
These were categorized as the following:
* Dead assignment 23
* Dead increment 4
* Dead initialization 6
* Dead nested assignment 18
Most of these are harmless, but since actual issues can hide among them,
we correct them.
That said, there were a few return values that were being ignored that
appeared to merit some correction:
* `destroy_callback()` in `cmd/zfs/zfs_main.c` ignored the error from
`destroy_batched()`. We handle it by returning -1 if there is an
error.
* `zfs_do_upgrade()` in `cmd/zfs/zfs_main.c` ignored the error from
`zfs_for_each()`. We handle it by doing a binary OR of the error
value from the subsequent `zfs_for_each()` call to the existing
value. This is how errors are mostly handled inside `zfs_for_each()`.
The error value here is passed to exit from the zfs command, so doing
a binary or on it is better than what we did previously.
* `get_zap_prop()` in `module/zfs/zcp_get.c` ignored the error from
`dsl_prop_get_ds()` when the property is not of type string. We
return an error when it does. There is a small concern that the
`zfs_get_temporary_prop()` call would handle things, but in the case
that it does not, we would be pushing an uninitialized numval onto
the lua stack. It is expected that `dsl_prop_get_ds()` will succeed
anytime that `zfs_get_temporary_prop()` does, so that not giving it a
chance to fix things is not a problem.
* `draid_merge_impl()` in `tests/zfs-tests/cmd/draid.c` used
`nvlist_add_nvlist()` twice in ways in which errors are expected to
be impossible, so we switch to `fnvlist_add_nvlist()`.
A few notable ones did not merit use of the return value, so we
suppressed it with `(void)`:
* `write_free_diffs()` in `lib/libzfs/libzfs_diff.c` ignored the error
value from `describe_free()`. A look through the commit history
revealed that this was intentional.
* `arc_evict_hdr()` in `module/zfs/arc.c` did not need to use the
returned handle from `arc_hdr_realloc()` because it is already
referenced in lists.
* `spa_vdev_detach()` in `module/zfs/spa.c` has a comment explicitly
saying not to use the error from `vdev_label_init()` because whatever
causes the error could be the reason why a detach is being done.
Unfortunately, I am not presently able to analyze the kernel modules
with Clang's static analyzer, so I could have missed some cases of this.
In cases where reports were present in code that is duplicated between
Linux and FreeBSD, I made a conscious effort to fix the FreeBSD version
too.
After this commit is merged, regressions like dee8934 should become
extremely obvious with Clang's static analyzer since a regression would
appear in the results as the only instance of unused code. That assumes
that Coverity does not catch the issue first.
My local branch with fixes from all of my outstanding non-draft pull
requests shows 118 reports from Clang's static anlayzer after this
patch. That is down by 51 from 169.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Cedric Berger <cedric@precidata.com>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13986
Various module parameters such as `zfs_arc_max` were originally
`uint64_t` on OpenSolaris/Illumos, but were changed to `unsigned long`
for Linux compatibility because Linux's kernel default module parameter
implementation did not support 64-bit types on 32-bit platforms. This
caused problems when porting OpenZFS to Windows because its LLP64 memory
model made `unsigned long` a 32-bit type on 64-bit, which created the
undesireable situation that parameters that should accept 64-bit values
could not on 64-bit Windows.
Upon inspection, it turns out that the Linux kernel module parameter
interface is extensible, such that we are allowed to define our own
types. Rather than maintaining the original type change via hacks to to
continue shrinking module parameters on 32-bit Linux, we implement
support for 64-bit module parameters on Linux.
After doing a review of all 64-bit kernel parameters (found via the man
page and also proposed changes by Andrew Innes), the kernel module
parameters fell into a few groups:
Parameters that were originally 64-bit on Illumos:
* dbuf_cache_max_bytes
* dbuf_metadata_cache_max_bytes
* l2arc_feed_min_ms
* l2arc_feed_secs
* l2arc_headroom
* l2arc_headroom_boost
* l2arc_write_boost
* l2arc_write_max
* metaslab_aliquot
* metaslab_force_ganging
* zfetch_array_rd_sz
* zfs_arc_max
* zfs_arc_meta_limit
* zfs_arc_meta_min
* zfs_arc_min
* zfs_async_block_max_blocks
* zfs_condense_max_obsolete_bytes
* zfs_condense_min_mapping_bytes
* zfs_deadman_checktime_ms
* zfs_deadman_synctime_ms
* zfs_initialize_chunk_size
* zfs_initialize_value
* zfs_lua_max_instrlimit
* zfs_lua_max_memlimit
* zil_slog_bulk
Parameters that were originally 32-bit on Illumos:
* zfs_per_txg_dirty_frees_percent
Parameters that were originally `ssize_t` on Illumos:
* zfs_immediate_write_sz
Note that `ssize_t` is `int32_t` on 32-bit and `int64_t` on 64-bit. It
has been upgraded to 64-bit.
Parameters that were `long`/`unsigned long` because of Linux/FreeBSD
influence:
* l2arc_rebuild_blocks_min_l2size
* zfs_key_max_salt_uses
* zfs_max_log_walking
* zfs_max_logsm_summary_length
* zfs_metaslab_max_size_cache_sec
* zfs_min_metaslabs_to_flush
* zfs_multihost_interval
* zfs_unflushed_log_block_max
* zfs_unflushed_log_block_min
* zfs_unflushed_log_block_pct
* zfs_unflushed_max_mem_amt
* zfs_unflushed_max_mem_ppm
New parameters that do not exist in Illumos:
* l2arc_trim_ahead
* vdev_file_logical_ashift
* vdev_file_physical_ashift
* zfs_arc_dnode_limit
* zfs_arc_dnode_limit_percent
* zfs_arc_dnode_reduce_percent
* zfs_arc_meta_limit_percent
* zfs_arc_sys_free
* zfs_deadman_ziotime_ms
* zfs_delete_blocks
* zfs_history_output_max
* zfs_livelist_max_entries
* zfs_max_async_dedup_frees
* zfs_max_nvlist_src_size
* zfs_rebuild_max_segment
* zfs_rebuild_vdev_limit
* zfs_unflushed_log_txg_max
* zfs_vdev_max_auto_ashift
* zfs_vdev_min_auto_ashift
* zfs_vnops_read_chunk_size
* zvol_max_discard_blocks
Rather than clutter the lists with commentary, the module parameters
that need comments are repeated below.
A few parameters were defined in Linux/FreeBSD specific code, where the
use of ulong/long is not an issue for portability, so we leave them
alone:
* zfs_delete_blocks
* zfs_key_max_salt_uses
* zvol_max_discard_blocks
The documentation for a few parameters was found to be incorrect:
* zfs_deadman_checktime_ms - incorrectly documented as int
* zfs_delete_blocks - not documented as Linux only
* zfs_history_output_max - incorrectly documented as int
* zfs_vnops_read_chunk_size - incorrectly documented as long
* zvol_max_discard_blocks - incorrectly documented as ulong
The documentation for these has been fixed, alongside the changes to
document the switch to fixed width types.
In addition, several kernel module parameters were percentages or held
ashift values, so being 64-bit never made sense for them. They have been
downgraded to 32-bit:
* vdev_file_logical_ashift
* vdev_file_physical_ashift
* zfs_arc_dnode_limit_percent
* zfs_arc_dnode_reduce_percent
* zfs_arc_meta_limit_percent
* zfs_per_txg_dirty_frees_percent
* zfs_unflushed_log_block_pct
* zfs_vdev_max_auto_ashift
* zfs_vdev_min_auto_ashift
Of special note are `zfs_vdev_max_auto_ashift` and
`zfs_vdev_min_auto_ashift`, which were already defined as `uint64_t`,
and passed to the kernel as `ulong`. This is inherently buggy on big
endian 32-bit Linux, since the values would not be written to the
correct locations. 32-bit FreeBSD was unaffected because its sysctl code
correctly treated this as a `uint64_t`.
Lastly, a code comment suggests that `zfs_arc_sys_free` is
Linux-specific, but there is nothing to indicate to me that it is
Linux-specific. Nothing was done about that.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Original-patch-by: Andrew Innes <andrew.c12@gmail.com>
Original-patch-by: Jorgen Lundman <lundman@lundman.net>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13984Closes#14004
If no errors are encountered, we read an uninitialized error value.
Clang's static analyzer complained about this.
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14007
Some header files define structures like this one:
typedef const struct zio_checksum_info {
/* ... */
const char *ci_name;
} zio_abd_checksum_func_t;
So we can use `zio_abd_checksum_func_t` for const declarations now.
It's not needed that we use the `const` qualifier again like this:
`const zio_abd_checksum_func_t *varname;`
This patch solves the double const qualifiers, which were found by
smatch.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Tino Reichardt <milky-zfs@mcmilk.de>
Closes#13961
ZED does not take any action for disk removal events if there is no
spare VDEV available. Added zpool_vdev_remove_wanted() in libzfs
and vdev_remove_wanted() in vdev.c to remove the VDEV through ZED
on removal event. This means that if you are running zed and
remove a disk, it will be properly marked as REMOVED.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#13797
In #13871, zfs_vdev_aggregation_limit_non_rotating and
zfs_vdev_aggregation_limit being signed was pointed out as a possible
reason not to eliminate an unnecessary MAX(unsigned, 0) since the
unsigned value was assigned from them.
There is no reason for these module parameters to be signed and upon
inspection, it was found that there are a number of other module
parameters that are signed, but should not be, so we make them unsigned.
Making them unsigned made it clear that some other variables in the code
should also be unsigned, so we also make those unsigned. This prevents
users from setting negative values that could potentially cause bad
behaviors. It also makes the code slightly easier to understand.
Mostly module parameters that deal with timeouts, limits, bitshifts and
percentages are made unsigned by this. Any that are boolean are left
signed, since whether booleans should be considered signed or unsigned
does not matter.
Making zfs_arc_lotsfree_percent unsigned caused a
`zfs_arc_lotsfree_percent >= 0` check to become redundant, so it was
removed. Removing the check was also necessary to prevent a compiler
error from -Werror=type-limits.
Several end of line comments had to be moved to their own lines because
replacing int with uint_t caused us to exceed the 80 character limit
enforced by cstyle.pl.
The following were kept signed because they are passed to
taskq_create(), which expects signed values and modifying the
OpenSolaris/Illumos DDI is out of scope of this patch:
* metaslab_load_pct
* zfs_sync_taskq_batch_pct
* zfs_zil_clean_taskq_nthr_pct
* zfs_zil_clean_taskq_minalloc
* zfs_zil_clean_taskq_maxalloc
* zfs_arc_prune_task_threads
Also, negative values in those parameters was found to be harmless.
The following were left signed because either negative values make
sense, or more analysis was needed to determine whether negative values
should be disallowed:
* zfs_metaslab_switch_threshold
* zfs_pd_bytes_max
* zfs_livelist_min_percent_shared
zfs_multihost_history was made static to be consistent with other
parameters.
A number of module parameters were marked as signed, but in reality
referenced unsigned variables. upgrade_errlog_limit is one of the
numerous examples. In the case of zfs_vdev_async_read_max_active, it was
already uint32_t, but zdb had an extern int declaration for it.
Interestingly, the documentation in zfs.4 was right for
upgrade_errlog_limit despite the module parameter being wrongly marked,
while the documentation for zfs_vdev_async_read_max_active (and friends)
was wrong. It was also wrong for zstd_abort_size, which was unsigned,
but was documented as signed.
Also, the documentation in zfs.4 incorrectly described the following
parameters as ulong when they were int:
* zfs_arc_meta_adjust_restarts
* zfs_override_estimate_recordsize
They are now uint_t as of this patch and thus the man page has been
updated to describe them as uint.
dbuf_state_index was left alone since it does nothing and perhaps should
be removed in another patch.
If any module parameters were missed, they were not found by `grep -r
'ZFS_MODULE_PARAM' | grep ', INT'`. I did find a few that grep missed,
but only because they were in files that had hits.
This patch intentionally did not attempt to address whether some of
these module parameters should be elevated to 64-bit parameters, because
the length of a long on 32-bit is 32-bit.
Lastly, it was pointed out during review that uint_t is a better match
for these variables than uint32_t because FreeBSD kernel parameter
definitions are designed for uint_t, whose bit width can change in
future memory models. As a result, we change the existing parameters
that are uint32_t to use uint_t.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Neal Gompa <ngompa@datto.com>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13875
When iterating through children physical ashifts for vdev, prefer
ones above the maximum logical ashift, that we can actually use,
but within the administrator defined maximum.
When selecting top-level vdev ashift, do not set it to the defined
maximum in case physical ashift is even higher, but just ignore one.
Using the maximum does not prevent misaligned writes, but reduces
space efficiency. Since ZFS tries to write data sequentially and
aggregates the writes, in many cases large misanigned writes may be
not as bad as the space penalty otherwise.
Allow internal physical ashifts for vdevs higher than SHIFT_MAX.
May be one day allocator or aggregation could benefit from that.
Reduce zfs_vdev_max_auto_ashift default from 16 (64KB) to 14 (16KB),
so that ZFS may still use bigger ashifts up to SHIFT_MAX (64KB),
but only if it really has to or explicitly told to, but not as an
"optimization".
There are some read-intensive NVMe SSDs that report Preferred Write
Alignment of 64KB, and attempt to build RAIDZ2 of those leads to a
space inefficiency that can't be justified. Instead these changes
make ZFS fall back to logical ashift of 12 (4KB) by default and
only warn user that it may be suboptimal for performance.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#13798
Previous flushing algorithm limited only total number of log blocks to
the minimum of 256K and 4x number of metaslabs in the pool. As result,
system with 1500 disks with 1000 metaslabs each, touching several new
metaslabs each TXG could grow spacemap log to huge size without much
benefits. We've observed one of such systems importing pool for about
45 minutes.
This patch improves the situation from five sides:
- By limiting maximum period for each metaslab to be flushed to 1000
TXGs, that effectively limits maximum number of per-TXG spacemap logs
to load to the same number.
- By making flushing more smooth via accounting number of metaslabs
that were touched after the last flush and actually need another flush,
not just ms_unflushed_txg bump.
- By applying zfs_unflushed_log_block_pct to the number of metaslabs
that were touched after the last flush, not all metaslabs in the pool.
- By aggressively prefetching per-TXG spacemap logs up to 16 TXGs in
advance, making log spacemap load process for wide HDD pool CPU-bound,
accelerating it by many times.
- By reducing zfs_unflushed_log_block_max from 256K to 128K, reducing
single-threaded by nature log processing time from ~10 to ~5 minutes.
As further optimization we could skip bumping ms_unflushed_txg for
metaslabs not touched since the last flush, but that would be an
incompatible change, requiring new pool feature.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12789
bcopy() has a confusing argument order and is actually a move, not a
copy; they're all deprecated since POSIX.1-2001 and removed in -2008,
and we shim them out to mem*() on Linux anyway
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12996
Add physical device size/capacity only for physical devices in
'zpool list -v' instead of displaying "-" in the SIZE column.
This would make it easier to see the individual device capacity and
to determine which spares are large enough to replace which devices.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Dipak Ghosh <dipak.ghosh@hpe.com>
Signed-off-by: Akash B <akash-b@hpe.com>
Closes#12561Closes#13106
`configure` now accepts `--enable-asan` and `--enable-ubsan` switches
which results in passing `-fsanitize=address`
and `-fsanitize=undefined`, respectively, to the compiler. Those
flags are enabled in GitHub workflows for ZTS and zloop. Errors
reported by both instrumentations are corrected, except for:
- Memory leak reporting is (temporarily) suppressed. The cost of
fixing them is relatively high compared to the gains.
- Checksum computing functions in `module/zcommon/zfs_fletcher*`
have UBSan errors suppressed. It is completely impractical
to enforce 64-byte payload alignment there due to performance
impact.
- There's no ASan heap poisoning in `module/zstd/lib/zstd.c`. A custom
memory allocator is used there rendering that measure
unfeasible.
- Memory leaks detection has to be suppressed for `cmd/zvol_id`.
`zvol_id` is run by udev with the help of `ptrace(2)`. Tracing is
incompatible with memory leaks detection.
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: szubersk <szuberskidamian@gmail.com>
Closes#12928
69 CSTYLED BEGINs remain, appx. 30 of which can be removed if cstyle(1)
had a useful policy regarding
CALL(ARG1,
ARG2,
ARG3);
above 2 lines. As it stands, it spits out *both*
sysctl_os.c: 385: continuation line should be indented by 4 spaces
sysctl_os.c: 385: indent by spaces instead of tabs
which is very cool
Another >10 could be fixed by removing "ulong" &al. handling.
I don't foresee anyone actually using it intentionally
(does it even exist in modern headers? why did it in the first place?).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12993
Evaluated every variable that lives in .data (and globals in .rodata)
in the kernel modules, and constified/eliminated/localised them
appropriately. This means that all read-only data is now actually
read-only data, and, if possible, at file scope. A lot of previously-
global-symbols became inlinable (and inlined!) constants. Probably
not in a big Wowee Performance Moment, but hey.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12899
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Mark Maybee <mark.maybee@delphix.com>
Closes#12951
Add properties, similar to pool properties, to each vdev.
This makes use of the existing per-vdev ZAP that was added as
part of device evacuation/removal.
A large number of read-only properties are exposed,
many of the members of struct vdev_t, that provide useful
statistics.
Adds support for read-only "removing" vdev property.
Adds the "allocating" property that defaults to "on" and
can be set to "off" to prevent future allocations from that
top-level vdev.
Supports user-defined vdev properties.
Includes support for properties.vdev in SYSFS.
Co-authored-by: Allan Jude <allan@klarasystems.com>
Co-authored-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Closes#11711
The only zdb utility require to read metaslab-related data during
read-only pool import because of spacemaps validation. Add global
variable which will allow zdb read spacemaps in case of readonly
import mode.
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Fedor Uporov <fuporov.vstack@gmail.com>
Closes#9095Closes#12687
