The RAIDZ and DRAID code is responsible for reporting checksum errors on
their child vdevs. Checksum errors represent events where a disk
returned data or parity that should have been correct, but was not. In
other words, these are instances of silent data corruption. The
checksum errors show up in the vdev stats (and thus `zpool status`'s
CKSUM column), and in the event log (`zpool events`).
Note, this is in contrast with the more common "noisy" errors where a
disk goes offline, in which case ZFS knows that the disk is bad and
doesn't try to read it, or the device returns an error on the requested
read or write operation.
RAIDZ/DRAID generate checksum errors via three code paths:
1. When RAIDZ/DRAID reconstructs a damaged block, checksum errors are
reported on any children whose data was not used during the
reconstruction. This is handled in `raidz_reconstruct()`. This is the
most common type of RAIDZ/DRAID checksum error.
2. When RAIDZ/DRAID is not able to reconstruct a damaged block, that
means that the data has been lost. The zio fails and an error is
returned to the consumer (e.g. the read(2) system call). This would
happen if, for example, three different disks in a RAIDZ2 group are
silently damaged. Since the damage is silent, it isn't possible to know
which three disks are damaged, so a checksum error is reported against
every child that returned data or parity for this read. (For DRAID,
typically only one "group" of children is involved in each io.) This
case is handled in `vdev_raidz_cksum_finish()`. This is the next most
common type of RAIDZ/DRAID checksum error.
3. If RAIDZ/DRAID is not able to reconstruct a damaged block (like in
case 2), but there happens to be additional copies of this block due to
"ditto blocks" (i.e. multiple DVA's in this blkptr_t), and one of those
copies is good, then RAIDZ/DRAID compares each sector of the data or
parity that it retrieved with the good data from the other DVA, and if
they differ then it reports a checksum error on this child. This
differs from case 2 in that the checksum error is reported on only the
subset of children that actually have bad data or parity. This case
happens very rarely, since normally only metadata has ditto blocks. If
the silent damage is extensive, there will be many instances of case 2,
and the pool will likely be unrecoverable.
The code for handling case 3 is considerably more complicated than the
other cases, for two reasons:
1. It needs to run after the main raidz read logic has completed. The
data RAIDZ read needs to be preserved until after the alternate DVA has
been read, which necessitates refcounts and callbacks managed by the
non-raidz-specific zio layer.
2. It's nontrivial to map the sections of data read by RAIDZ to the
correct data. For example, the correct data does not include the parity
information, so the parity must be recalculated based on the correct
data, and then compared to the parity that was read from the RAIDZ
children.
Due to the complexity of case 3, the rareness of hitting it, and the
minimal benefit it provides above case 2, this commit removes the code
for case 3. These types of errors will now be handled the same as case
2, i.e. the checksum error will be reported against all children that
returned data or parity.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#11735
Avoids tripping on asserts when doing pool recovery.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#11739
The `rr_code` field in `raidz_row_t` is unused.
This commit removes the field, as well as the code that's used to set
it.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#11736
Don't handle (incorrectly) kmem_zalloc() failure. With KM_SLEEP,
will never return NULL.
Free the data allocated for non-virtual kstats when deleting the object.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11767
zhold() wraps igrab() on Linux, and igrab() may fail when the inode
is in the process of being deleted. This means zhold() must only be
called when a reference exists and therefore it cannot be deleted.
This is the case for all existing consumers so add a VERIFY and a
comment explaining this requirement.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Adam Moss <c@yotes.com>
Closes#11704
The man page was missing these two permissions.
Add the missing permissions to the man page.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jeremy Faulkner <gldisater@gldis.ca>
Closes#11727
Create a new section of tests to run with acltype=off.
For now the only test we have is for the DOS mode READONLY attribute on
FreeBSD.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11734
To make use of zfs_refcount_held tunable it should be a module
parameter in open-zfs. Also, since the macros will auto-generate OS
specific tunables, removed the existing zfs_refcount_held reference
in module/os/freebsd/zfs/sysctl_os.c.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Don Brady <don.brady@delphix.com>
Closes#11753
You can't use user_run to eval ksh functions defined in libtest unless
you include libtest in the user shell.
Fix xattr_003_neg by:
* include libtest in the user shell
* *then* run get_xattr
* assert this fails
* use variables for filenames so they don't change in the user's shell
* don't log the contents of /etc/passwd
* cleanup all byproducts
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11185
The current user_run often does not work as expected. Commands are run
in a different shell, with a different environment, and all output is
discarded.
Simplify user_run to retain the current environment, eliminate eval,
and feed the command string into ksh. Enhance the logging for
user_run so we can see out and err.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11185
Add parsing of the rewind options.
When I was upstreaming the change [1], I omitted the part where we
detect that the pool should be rewind. When the FreeBSD repo has
synced with the OpenZFS, this part of the code was removed.
[1] FreeBSD repo: 277f38abffc6a8160b5044128b5b2c620fbb970c
[2] OpenZFS repo: f2c027bd6a
External-issue: https://bugs.freebsd.org/bugzilla/show_bug.cgi?id=254152
Originally reviewed by: tsoome, allanjude
Originally reviewed by: kevans (ok from high-level overview)
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Mariusz Zaborski <oshogbo@vexillium.org>
Closes#11730
Resolve some oddities in zfsdev_close() which could result in a
panic and were not present in the equivalent function for Linux.
- Remove unused definition ZFS_MIN_MINOR
- FreeBSD: Simplify zfsdev state destruction
- Assert zs_minor is valid in zfsdev_close
- Make locking around zfsdev state match Linux
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11720
This deserializes otherwise non-contending operations.
The previous scheme of using 17 locks hashed by curthread runs into
conflicts very quickly. Check the pull request for sample results.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#11153
This will allow platforms to implement it as they see fit, in particular
in a different manner than rrm locks.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#11153
They are not very useful and hard to implement in the rms routine
the code is about to start using.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#11153
1. even up ifdefs
2. drop the arguably useless teardown lock asserts -- nothing else
checks for it
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#11153
They are expected to fail only in corner cases.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#11153
Importing a pool using the cachefile is ideal to reduce the time
required to import a pool. However, if the devices associated with
a pool in the cachefile have changed, then the import would fail.
This can easily be corrected by doing a normal import which would
then read the pool configuration from the labels.
The goal of this change is make importing using a cachefile more
resilient and auto-correcting. This is accomplished by having
the cachefile import logic automatically fallback to reading the
labels of the devices similar to a normal import. The main difference
between the fallback logic and a normal import is that the cachefile
import logic will only look at the device directories that were
originally used when the cachefile was populated. Additionally,
the fallback logic will always import by guid to ensure that only
the pools in the cachefile would be imported.
External-issue: DLPX-71980
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Wilson <gwilson@delphix.com>
Closes#11716
The manual page change in ecc277c has introduced whitespace on
line ends.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Martin Matuska <mm@FreeBSD.org>
Closes#11722
A few deadman tunables ended up in the wrong sysctl node.
Move them to vfs.zfs.deadman.*
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11715
Add branch hints and constify the intermediate evaluations of
left/right params in VERIFY3*().
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Adam Moss <c@yotes.com>
Closes#11708
Some .h files that were added were missed in this Makefile. Since
they are .h files, their being missing only resulted in them
disappeared from the dist archive.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Closes#11705
Our checkstyle doesn't work well on Ubuntu 20.04,
temporary pin it to 18.04.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Melikov <mail@gmelikov.ru>
Closes#11713
Added errno mappings to unmount_one() in libzfs. Changed do_unmount()
implementation to return errno errors directly like is done for
do_mount() and others.
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@delphix.com>
Closes#11681
vdev_id uses the /dev/mapper/ symlinks to resolve a UUID to a dm name
(like dm-1). However on some multipath setups, there is no /dev/mapper/
entry for the UUID at the time vdev_id is called by udev. However,
this isn't necessarily needed, as we may be able to resolve the dm
name from the $DEVNAME that udev passes us (like DEVNAME="/dev/dm-1").
This patch tries to resolve the dm name from $DEVNAME first, before
falling back to looking in /dev/mapper/. This fixed an issue where the
by-vdev names weren't reliably showing up on one of our nodes.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#11698
events_002 exercises the ZED, ensuring that it neither misses events,
nor reporting events twice.
On slow test hardware, some of the timeouts are insufficient to allow
the ZED to properly settle. Conversely, on fast hardware these same
timeouts are too long, unnecessarily slowing the test run.
Instead of using a fixed timeout, wait for the expected final event
before returning. Additionally, wait with a timeout for unexpected
events to avoid missing them if they show up late.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Antonio Russo <aerusso@aerusso.net>
Closes#11703
zil_replaying(zil, tx) has the side-effect of informing the ZIL that an
entry has been replayed in the (still open) tx. The ZIL uses that
information to record the replay progress in the ZIL header when that
tx's txg syncs.
ZPL log entries are not idempotent and logically dependent and thus
calling zil_replaying() is necessary for correctness.
For ZVOLs the question of correctness is more nuanced: ZVOL logs only
TX_WRITE and TX_TRUNCATE, both of which are idempotent. Logical
dependencies between two records exist only if the write or discard
request had sync semantics or if the ranges affected by the records
overlap.
Thus, at a first glance, it would be correct to restart replay from
the beginning if we crash before replay completes. But this does not
address the following scenario:
Assume one log record per LWB.
The chain on disk is
HDR -> 1:W(1, "A") -> 2:W(1, "B") -> 3:W(2, "X") -> 4:W(3, "Z")
where N:W(O, C) represents log entry number N which is a TX_WRITE of C
to offset A.
We replay 1, 2 and 3 in one txg, sync that txg, then crash.
Bit flips corrupt 2, 3, and 4.
We come up again and restart replay from the beginning because
we did not call zil_replaying() during replay.
We replay 1 again, then interpret 2's invalid checksum as the end
of the ZIL chain and call replay done.
The replayed zvol content is "AX".
If we had called zil_replaying() the HDR would have pointed to 3
and our resumed replay would not have replayed anything because
3 was corrupted, resulting in zvol content "BX".
If 3 logically depends on 2 then the replay corrupted the ZVOL_OBJ's
contents.
This patch adds the zil_replaying() calls to the replay functions.
Since the callbacks in the replay function need the zilog_t* pointer
so that they can call zil_replaying() we open the ZIL while
replaying in zvol_create_minor(). We also verify that replay has
been done when on-demand-opening the ZIL on the first modifying
bio.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Christian Schwarz <me@cschwarz.com>
Closes#11667
* Restore original kern.corefile value after the test.
* Don't leave behind a frozen pool.
* Clean up leftover vdev files.
* Make zpool_002_pos and zpool_003_pos consistent in their handling of
core files while here.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11694
Docs for send and receive do not explain behavior when sending a
compressed stream then receiving on a host that overrides compression
with -o compress=value.
The data from the send stream is written as it was from the send is
the compressed form but the compression algorithm set on the receiver
is the overridden version which causes some confusion as to what
algorithm was actually used.
Updated man docs to clarify behavior
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed By: Allan Jude <allanjude@freebsd.org>
Signed-off-by: manfromafar <manfromafar@outlook.com>
Closes#11690
ZFS_READONLY represents the "DOS R/O" attribute.
When that flag is set, we should behave as if write access
were not granted by anything in the ACL. In particular:
We _must_ allow writes after opening the file r/w, then
setting the DOS R/O attribute, and writing some more.
(Similar to how you can write after fchmod(fd, 0444).)
Restore these semantics which were lost on FreeBSD when refactoring
zfs_write. To my knowledge Linux does not actually expose this flag,
but we'll need it to eventually so I've added the supporting checks.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11693
For some reason cppcheck 1.90 is generating an invalidSyntax warning
when the BF64_SET macro is used in the zstream source. The same
warning is not reported by cppcheck 2.3, nor is their any evident
problem with the expanded macro. This appears to be an issue with
this version of cppcheck. This commit annotates the source to suppress
the warning.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11700
When populating a ZIL destination buffer ensure it is always
zeroed before its contents are constructed.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Tom Caputi <caputit1@tcnj.edu>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11687
Even when supplied with an abd to abd_get_offset_struct(), the call
to abd_get_offset_impl() can allocate a different abd. Ensure to
call abd_fini_struct() on the abd that is not used.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Closes#11683
Wire up the --enable-debug flag for configure to the FreeBSD module
build. Add --enable-invariants.
The running FreeBSD kernel config is used to detect whether to enable
INVARIANTS if not explicitly specified with --enable-invariants or
--disable-invariants.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11678
Bring the output of the removal status in line with the other
"fields" that zpool status outputs, and thus allows an parser to
easier detect this as continuation of the 'remove:' output.
Before:
remove: Removal of vdev 0 copied 282G in 0h9m, completed on [...]
776K memory used for removed device mappings
Now:
remove: Removal of vdev 0 copied 282G in 0h9m, completed on [...]
776K memory used for removed device mappings
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
Closes#11674
Avoid following the error path when the operation in fact succeeded.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: James Wah <james@laird-wah.net>
Closes#11651
The spl_kmem_alloc showed up in some flamegraphs in a single-threaded
4k sync write workload at 85k IOPS on an
Intel(R) Xeon(R) Silver 4215 CPU @ 2.50GHz.
Certainly not a huge win but I believe the change is clean and
easy to maintain down the road.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Christian Schwarz <me@cschwarz.com>
Closes#11666
This value does work as expected, and is documented in the manpage.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jake Howard <git@theorangeone.net>
Closes#11670
When a device which is actively trimming or initializing becomes
FAULTED, and therefore no longer writable, cancel the active
TRIM or initialization. When the device is merely taken offline
with `zpool offline` then stop the operation but do not cancel it.
When the device is brought back online the operation will be
resumed if possible.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Vipin Kumar Verma <vipin.verma@hpe.com>
Signed-off-by: Srikanth N S <srikanth.nagasubbaraoseetharaman@hpe.com>
Closes#11588
The function has three similar pieces of code: for read-behind pages,
requested pages and read-ahead pages. All three pieces had an
assert to ensure that the page is not mapped. Later the assert was
relaxed to require that the page is not mapped for writing. But that
was done in two places out of three. This change fixes the third piece,
read-ahead.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andriy Gapon <avg@FreeBSD.org>
Closes#11654
Several of the TRIM tests were based of the initialize tests and
then adapted for TRIM. The zpool_trim_start_and_cancel_pos.ksh
test was intended to be one such test but it was overlooked and
actually never adapted. Update it accordingly.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11649
After 35ec517 it has become possible to import ZFS pools witn an
active org.illumos:edonr feature on FreeBSD, leading to a panic.
In addition, "zpool status" reported all pools without edonr
as upgradable and "zpool upgrade -v" reported edonr in the list
of upgradable features.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Martin Matuska <mm@FreeBSD.org>
Closes#11653
The bio_*_acct functions became GPL exports, which causes the
kernel modules to refuse to compile. This replaces code with
alternate function calls to the disk_*_io_acct interfaces, which
are not GPL exports. This change was added in kernel commit
99dfc43ecbf67f12a06512918aaba61d55863efc.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#11639
The struct bio member bi_disk was moved underneath a new member named
bi_bdev. So all attempts to reference bio->bi_disk need to now become
bio->bi_bdev->bd_disk.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#11639
The metaslab_disable() call may block waiting for a txg sync.
Therefore it's important that vdev_rebuild_thread release the
SCL_CONFIG read lock it is holding before this call. Failure
to do so can result in the txg_sync thread getting blocked
waiting for this lock which results in a deadlock.
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewd-by: Srikanth N S <srikanth.nagasubbaraoseetharaman@hpe.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11647
Calling vdev_free() only requires the we acquire the spa config
SCL_STATE_ALL locks, not the SCL_ALL locks. In particular, we need
need to avoid taking the SCL_CONFIG lock (included in SCL_ALL) as a
writer since this can lead to a deadlock. The txg_sync_thread() may
block in spa_txg_history_init_io() when taking the SCL_CONFIG lock
as a reading when it detects there's a pending writer.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11585
Given a DM device name, the old vdev_id script would extract any text
after a 'p' as the partition number. It then appends "-part" + the
partition number to the name, giving a by-vdev name like "L0-part5".
This works fine if the DM name is like 'dm-2p5', but doesn't work if
the DM name is a multipath name like "mpatha". In those cases it
incorrectly matches the 'p' in "mpatha", giving by-vdev names like
"L0-partatha".
This patch fixes the issue by making the partition regex match stricter.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#11637
On Linux increase the maximum allowed size of the src nvlist which
can be passed to the /dev/zfs ioctl. Originally, this was set
to a maximum of KMALLOC_MAX_SIZE (4M) because it was kmalloc'd.
Since that time it's been converted to a vmalloc so that's no
longer a hard limit, and it's desirable for `zfs send/recv` to
allow larger nvlists so more snapshots can be sent at once.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6572Closes#11638
