2 Commits

Author	SHA1	Message	Date
Brian Behlendorf	ff3e2e3c70	Perform KABI checks in parallel ... Reduce the time required for ./configure to perform the needed KABI checks by allowing kbuild to compile multiple test cases in parallel. This was accomplished by splitting each test's source code from the logic handling whether that code could be compiled or not. By introducing this split it's possible to minimize the number of times kbuild needs to be invoked. As importantly, it means all of the tests can be built in parallel. This does require a little extra care since we expect some tests to fail, so the --keep-going (-k) option must be provided otherwise some tests may not get compiled. Furthermore, since a failure during the kbuild modpost phase will result in an early exit; the final linking phase is limited to tests which passed the initial compilation and produced an object file. Once everything has been built the configure script proceeds as previously. The only significant difference is that it now merely needs to test for the existence of a .ko file to determine the result of a given test. This vastly speeds up the entire process. New test cases should use ZFS_LINUX_TEST_SRC to declare their test source code and ZFS_LINUX_TEST_RESULT to check the result. All of the existing kernel-*.m4 files have been updated accordingly, see config/kernel-current-time.m4 for a basic example. The legacy ZFS_LINUX_TRY_COMPILE macro has been kept to handle special cases but it's use is not encouraged. master (secs) patched (secs) ------------- ---------------- autogen.sh 61 68 configure 137 24 (~17% of current run time) make -j $(nproc) 44 44 make rpms 287 150 Reviewed-by: Tony Hutter <hutter2@llnl.gov> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov> Closes #8547 Closes #9132 Closes #9341 Conflicts: Makefile.am config/kernel-fpu.m4	2020-01-22 13:49:01 -08:00
Brian Behlendorf	d441e85dd7	Add support for autoexpand property ... While the autoexpand property may seem like a small feature it depends on a significant amount of system infrastructure. Enough of that infrastructure is now in place that with a few modifications for Linux it can be supported. Auto-expand works as follows; when a block device is modified (re-sized, closed after being open r/w, etc) a change uevent is generated for udev. The ZED, which is monitoring udev events, passes the change event along to zfs_deliver_dle() if the disk or partition contains a zfs_member as identified by blkid. From here the device is matched against all imported pool vdevs using the vdev_guid which was read from the label by blkid. If a match is found the ZED reopens the pool vdev. This re-opening is important because it allows the vdev to be briefly closed so the disk partition table can be re-read. Otherwise, it wouldn't be possible to report the maximum possible expansion size. Finally, if the property autoexpand=on a vdev expansion will be attempted. After performing some sanity checks on the disk to verify that it is safe to expand, the primary partition (-part1) will be expanded and the partition table updated. The partition is then re-opened (again) to detect the updated size which allows the new capacity to be used. In order to make all of the above possible the following changes were required: * Updated the zpool_expand_001_pos and zpool_expand_003_pos tests. These tests now create a pool which is layered on a loopback, scsi_debug, and file vdev. This allows for testing of non- partitioned block device (loopback), a partition block device (scsi_debug), and a file which does not receive udev change events. This provided for better test coverage, and by removing the layering on ZFS volumes there issues surrounding layering one pool on another are avoided. * zpool_find_vdev_by_physpath() updated to accept a vdev guid. This allows for matching by guid rather than path which is a more reliable way for the ZED to reference a vdev. * Fixed zfs_zevent_wait() signal handling which could result in the ZED spinning when a signal was not handled. * Removed vdev_disk_rrpart() functionality which can be abandoned in favor of kernel provided blkdev_reread_part() function. * Added a rwlock which is held as a writer while a disk is being reopened. This is important to prevent errors from occurring for any configuration related IOs which bypass the SCL_ZIO lock. The zpool_reopen_007_pos.ksh test case was added to verify IO error are never observed when reopening. This is not expected to impact IO performance. Additional fixes which aren't critical but were discovered and resolved in the course of developing this functionality. * Added PHYS_PATH="/dev/zvol/dataset" to the vdev configuration for ZFS volumes. This is as good as a unique physical path, while the volumes are not used in the test cases anymore for other reasons this improvement was included. Reviewed by: Richard Elling <Richard.Elling@RichardElling.com> Signed-off-by: Sara Hartse <sara.hartse@delphix.com> Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov> Closes #120 Closes #2437 Closes #5771 Closes #7366 Closes #7582 Closes #7629	2018-07-23 15:40:15 -07:00