- Make prefetch distance adaptive: up to 4MB prefetch doubles for
every, hit same as before, but after that it grows by 1/8 every time
the prefetch read does not complete in time to satisfy the demand.
My tests show that 4MB is sufficient for wide NVMe pool to saturate
single reader thread at 2.5GB/s, while new 64MB maximum allows the
same thread to reach 1.5GB/s on wide HDD pool. Further distance
increase may increase speed even more, but less dramatic and with
higher latency.
- Allow early reuse of inactive prefetch streams: streams that never
saw hits can be reused immediately if there is a demand, while others
can be reused after 1s of inactivity, starting with the oldest. After
2s of inactivity streams are deleted to free resources same as before.
This allows by several times increase strided read performance on HDD
pool in presence of simultaneous random reads, previously filling the
zfetch_max_streams limit for seconds and so blocking most of prefetch.
- Always issue intermediate indirect block reads with SYNC priority.
Each of those reads if delayed for longer may delay up to 1024 other
block prefetches, that may be not good for wide pools.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#13452
This issue was discovered by zloop runs. When a mirror or other
redundant top-level vdev has a disk failure, and the disk is replaced,
the rebuild process occurs. A removal can happen while this is in
progress. If the removal completes before the rebuild does, the
removal process will try to free the vdev that is still in use.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#13498
Original Log Size Limit implementation blocked all writes in case of
limit reached until the TXG is committed and the log is freed. It
caused huge delays and following speed spikes in application writes.
This implementation instead smoothly throttles writes, using exactly
the same mechanism as used for dirty data.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: jxdking <lostking2008@hotmail.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Issue #12284Closes#13476
It turns out that "do LZ4 and zstd-1 both fail" is a great heuristic
for "don't even bother trying higher zstd tiers".
By way of illustration:
$ cat /incompress | mbuffer | zfs recv -o compression=zstd-12 evenfaster/lowcomp_1M_zstd12_normal
summary: 39.8 GiByte in 3min 40.2sec - average of 185 MiB/s
$ echo 3 | sudo tee /sys/module/zzstd/parameters/zstd_lz4_pass
3
$ cat /incompress | mbuffer -m 4G | zfs recv -o compression=zstd-12 evenfaster/lowcomp_1M_zstd12_patched
summary: 39.8 GiByte in 48.6sec - average of 839 MiB/s
$ sudo zfs list -p -o name,used,lused,ratio evenfaster/lowcomp_1M_zstd12_normal evenfaster/lowcomp_1M_zstd12_patched
NAME USED LUSED RATIO
evenfaster/lowcomp_1M_zstd12_normal 39549931520 42721221632 1.08
evenfaster/lowcomp_1M_zstd12_patched 39626399744 42721217536 1.07
$ python3 -c "print(39626399744 - 39549931520)"
76468224
$
I'll take 76 MB out of 42 GB for > 4x speedup.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#13244
We want `zpool import` to be highly robust and never panic, even
when encountering corrupt metadata. This is already handled in the
arc_read() code path, which covers most cases, but spa_load_verify_cb()
relies on zio_read() and is responsible for verifying the block pointer.
During import it is also possible to encounter blocks pointers which
contain ZIO_COMPRESS_INHERIT and ZIO_CHECKSUM_INHERIT values. Relax
the verification function slightly to allow this.
Futhermore, extend dsl_scan_recurse() to verify the block pointer
contents of level zero blocks which are not of type DMU_OT_DNODE or
DMU_OT_OBJSET. This is handled by arc_read() in the other cases.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13124Closes#13360
There are times when end-users may wish to have
a fast and convenient method to get zpool guid
without having to use libzfs. This commit
exposes the zpool guid via kstats in similar
manner to the zpool state.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andrew Walker <awalker@ixsystems.com>
Closes#13466
Recognise initial whitespace, + in both cases,
and - also in unsigneds
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13434
Linux passes -Wframe-larger-than=1024, which breaks
our build in a number of places with -Werror.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#13450
Refcount creation for abd_zero_scatter->abd_children is redundant in
abd_alloc_zero_scatter, as it has been done in abd_init_struct.
In addition, abd_children is undefined when ZFS_DEBUG is disabled, the
reference of abd_children in abd_alloc_zero_scatter breaks build of
libzpool when ZFS_DEBUG is disabled.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Ping Huang <huangping@smartx.com>
Closes#13429
clang-15 emits the following error message for functions without
a prototype:
fs/zfs/os/linux/spl/spl-kmem-cache.c:1423:27: error:
a function declaration without a prototype is deprecated
in all versions of C [-Werror,-Wstrict-prototypes]
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Aidan Harris <me@aidanharr.is>
Closes#13421
I genuinely don't know why this didn't come up before,
but adding the LZ4 early abort pointed out this flaw,
in which we're allocating a buffer of one size, and
then telling the compressor that we're handing it buffers
of a different size, which may be Very Different - say,
allocating 512b and then telling it the inputs are 128k.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Amanakis <gamanakis@gmail.com>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#13375
When calculating mg_aliquot alike to #12046 use number of unique data
disks in the vdev, not the total number of children vdev. Increase
default value of the tunable from 512KB to 1MB to compensate.
Before this change each disk in striped pool was getting 512KB of
sequential data, in 2-wide mirror -- 1MB, in 3-wide RAIDZ1 -- 768KB.
After this change in all the cases each disk should get 1MB.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#13388
Holding a dbuf is a common operation which can become highly contended
in dbuf_find() when acquiring the dbuf hash mutex. This is particularly
true on Linux when reading/writing volumes since by default up to 32
threads from the zvol_taskq may be taking a hold of the same dbuf.
This should also be observable on FreeBSD as long as there are enough
processes accessing the volume concurrently.
This is further aggregrated by the fact that only the block id will
be unique when calculating the dbuf hash for a single volume. The
objset id, object id, and level will be the same for data blocks.
This has been observed to result in a somehwat less than uniform hash
distribution and a longer than expected max hash chain depth (~20)
on a large memory system (256 GB) using volumes.
This commit improves the siutation by switching the hash mutex to
an rwlock to allow concurrent lookups, and increasing DBUF_RWLOCKS
from 2048 to 8192 to further reduce the odds of a hash collision.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13405
Page writebacks with WB_SYNC_NONE can take several seconds to complete
since they wait for the transaction group to close before being
committed. This is usually not a problem since the caller does not
need to wait. However, if we're simultaneously doing a writeback
with WB_SYNC_ALL (e.g via msync), the latter can block for several
seconds (up to zfs_txg_timeout) due to the active WB_SYNC_NONE
writeback since it needs to wait for the transaction to complete
and the PG_writeback bit to be cleared.
This commit deals with 2 cases:
- No page writeback is active. A WB_SYNC_ALL page writeback starts
and even completes. But when it's about to check if the PG_writeback
bit has been cleared, another writeback with WB_SYNC_NONE starts.
The sync page writeback ends up waiting for the non-sync page
writeback to complete.
- A page writeback with WB_SYNC_NONE is already active when a
WB_SYNC_ALL writeback starts. The WB_SYNC_ALL writeback ends up
waiting for the WB_SYNC_NONE writeback.
The fix works by carefully keeping track of active sync/non-sync
writebacks and committing when beneficial.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Shaan Nobee <sniper111@gmail.com>
Closes#12662Closes#12790
- Prefer O_* flags over F* flags that mostly mirror O_* flags anyway,
but O_* flags seem to be preferred.
- Simplify the code as all the F*SYNC flags were defined as FFSYNC flag.
- Don't define FRSYNC flag, so we don't generate unnecessary ZIL commits.
- Remove EXCL define, FreeBSD ignores the excl argument for zfs_create()
anyway.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Pawel Jakub Dawidek <pawel@dawidek.net>
Closes#13400
Commit 361a7e8 (log xattr=sa create/remove/update to ZIL) introduced a
TX_SETSAXATTR, but missed to add a corresponding entry in
zvol_replay_vector. Adding a missing replay entry in zvol_replay_vector.
Reviewed-by: Christian Schwarz <christian.schwarz@nutanix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jitendra Patidar <jitendra.patidar@nutanix.com>
Closes#13396Closes#13395
Clang 13.0.0 added support for `Wunused-but-set-parameter` and
`-Wunused-but-set-variable` which correctly detects two unused
variables in zstd resulting in a build failure. This commit
annotates these instances accordingly.
https://releases.llvm.org/13.0.1/tools/clang/docs/ReleaseNotes.html#id6
In FSE_createCTable(), malloc() is intentionally defined as NULL when
compiled in the kernel so the variable is unused.
zstd/lib/compress/fse_compress.c:307:12: error: variable 'size'
set but not used [-Werror,-Wunused-but-set-variable]
Additionally, in ZSTD_seqDecompressedSize() the assert is compiled
out similarly resulting in an unused variable.
zstd/lib/compress/zstd_compress_superblock.c:412:12: error: variable
'litLengthSum' set but not used [-Werror,-Wunused-but-set-variable]
Reviewed-by: Rich Ercolani <rincebrain@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13382
Increase the default allowed maximum recordsize from 1M to 16M.
As described in the zfs(4) man page, there are significant costs
which need to be considered before using very large blocks.
However, there are scenarios where they make good sense and
it should no longer be necessary to artificially restrict their
use behind a module option.
Note that for 32-bit platforms we continue to leave this
restriction in place due to the limited virtual address space
available (256-512MB). On these systems only a handful
of blocks could be cached at any one time severely impacting
performance and potentially stability.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12830Closes#13302
When using a Linux kernel which predates the iov_iter interface the
O_APPEND flag should be applied in zpl_aio_write() via the call to
generic_write_checks(). The updated pos variable was incorrectly
ignored resulting in the current offset being used.
This issue should only realistically impact the RHEL/CentOS 7.x
kernels which are based on Linux 3.10.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13370Closes#13377
Linux 5.12 PPC 5.12 get_user() and __copy_from_user_inatomic()
inline helpers very indirectly include a reference to the GPL'd
array mmu_feature_keys[] and fails to build. Workaround this by
using copy_from_user() and throwing EFAULT for any calls to
__copy_from_user_inatomic(). This is a workaround until a fix
for Linux commit 7613f5a66becfd0e43a0f34de8518695888f5458
"powerpc/64s/kuap: Use mmu_has_feature()" is fully addressed.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Authored-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: szubersk <szuberskidamian@gmail.com>
Closes#11958Closes#12590Closes#13367
Previous flushing algorithm limited only total number of log blocks to
the minimum of 256K and 4x number of metaslabs in the pool. As result,
system with 1500 disks with 1000 metaslabs each, touching several new
metaslabs each TXG could grow spacemap log to huge size without much
benefits. We've observed one of such systems importing pool for about
45 minutes.
This patch improves the situation from five sides:
- By limiting maximum period for each metaslab to be flushed to 1000
TXGs, that effectively limits maximum number of per-TXG spacemap logs
to load to the same number.
- By making flushing more smooth via accounting number of metaslabs
that were touched after the last flush and actually need another flush,
not just ms_unflushed_txg bump.
- By applying zfs_unflushed_log_block_pct to the number of metaslabs
that were touched after the last flush, not all metaslabs in the pool.
- By aggressively prefetching per-TXG spacemap logs up to 16 TXGs in
advance, making log spacemap load process for wide HDD pool CPU-bound,
accelerating it by many times.
- By reducing zfs_unflushed_log_block_max from 256K to 128K, reducing
single-threaded by nature log processing time from ~10 to ~5 minutes.
As further optimization we could skip bumping ms_unflushed_txg for
metaslabs not touched since the last flush, but that would be an
incompatible change, requiring new pool feature.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12789
Currently, determining which datasets are affected by corruption is
a manual process.
The primary difficulty in reporting the list of affected snapshots is
that since the error was initially found, the snapshot where the error
originally occurred in, may have been deleted. To solve this issue, we
add the ID of the head dataset of the original snapshot which the error
was detected in, to the stored error report. Then any time a filesystem
is deleted, the errors associated with it are deleted as well. Any time
a clone promote occurs, we modify reports associated with the original
head to refer to the new head. The stored error reports are identified
by this head ID, the birth time of the block which the error occurred
in, as well as some information about the error itself are also stored.
Once this information is stored, we can find the set of datasets
affected by an error by walking back the list of snapshots in the given
head until we find one with the appropriate birth txg, and then traverse
through the snapshots of the clone family, terminating a branch if the
block was replaced in a given snapshot. Then we report this information
back to libzfs, and to the zpool status command, where it is displayed
as follows:
pool: test
state: ONLINE
status: One or more devices has experienced an error resulting in data
corruption. Applications may be affected.
action: Restore the file in question if possible. Otherwise restore the
entire pool from backup.
see: https://openzfs.github.io/openzfs-docs/msg/ZFS-8000-8A
scan: scrub repaired 0B in 00:00:00 with 800 errors on Fri Dec 3
08:27:57 2021
config:
NAME STATE READ WRITE CKSUM
test ONLINE 0 0 0
sdb ONLINE 0 0 1.58K
errors: Permanent errors have been detected in the following files:
test@1:/test.0.0
/test/test.0.0
/test/1clone/test.0.0
A new feature flag is introduced to mark the presence of this change, as
well as promotion and backwards compatibility logic. This is an updated
version of #9175. Rebase required fixing the tests, updating the ABI of
libzfs, updating the man pages, fixing bugs, fixing the error returns,
and updating the old on-disk error logs to the new format when
activating the feature.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Co-authored-by: TulsiJain <tulsi.jain@delphix.com>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#9175Closes#12812
It turns out, no, in fact, ZERO_RANGE and PUNCH_HOLE do
have differing semantics in some ways - in particular,
one requires KEEP_SIZE, and the other does not.
Also added a zero-range test to catch this, corrected a flaw
that made the punch-hole test succeed vacuously, and a typo
in file_write.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#13329Closes#13338
In hypothetical case of non-linear ABD with single segment, multiple
to page size but not aligned to it, vdev_geom_fill_unmap_cb() could
fill one page less into bio_ma array.
I am not sure it is exploitable, but better to be safe than sorry.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reported-by: Mark Johnston <markj@FreeBSD.org>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#13345
This can be reverted once we're sure nobody's using them anymore
(post-3.0 release?)
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13274
Originally it was thought it would be useful to split up the kmods
by functionality. This would allow external consumers to only load
what was needed. However, in practice we've never had a case where
this functionality would be needed, and conversely managing multiple
kmods can be awkward. Therefore, this change merges all but the
spl.ko kmod in to a single zfs.ko kmod.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13274
These are displayed as the descriptions of the sysctl's on FreeBSD
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Closes#13334
As of the 5.17 kernel the GENHD_FL_EXT_DEVT flag has been removed
and the GENHD_FL_NO_PART_SCAN flag renamed GENHD_FL_NO_PART. Update
zvol_alloc() to set GENHD_FL_NO_PART for the newer kernels which
is sufficient. The behavior for prior kernels remains unchanged.
1ebe2e5f ("block: remove GENHD_FL_EXT_DEVT")
46e7eac6 ("block: rename GENHD_FL_NO_PART_SCAN to GENHD_FL_NO_PART")
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13294Closes#13297
FreeBSD's memory management system uses its own error numbers and gets
confused when these VOPs return EIO.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reported-by: Peter Holm <pho@FreeBSD.org>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#13311
For legacy reasons, a couple of VOPs have to return error numbers that
don't come from the usual errno namespace. To handle the cases where
ZFS_ENTER or ZFS_VERIFY_ZP fail, we need to be able to override the
default error return value of EIO. Extend the macros to permit this.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#13311
An earlier commit introduces AT_MODE into the shared kernel sources,
instead of the preferred existing ATTR_MODE use.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Signed-off-by: Jorgen lundman <lundman@lundman.net>
Closes#13293
I got the status backward (B_FALSE for fixed, rather than B_TRUE for
flex); before:
$ zfs get mountpoint tarta-zoot -r
NAME PROPERTY VALUE SOURCE
tarta-zoot mountpoint / local
tarta-zoot/PAGEFILE.SYS mountpoint - -
tarta-zoot/etc mountpoint /etc inherited from tarta-zoot
tarta-zoot/home mountpoint /home inherited from tarta-zoot
tarta-zoot/home/xspon mountpoint /home/xspon inherited from tarta-zoot
tarta-zoot/home/nabijaczleweli mountpoint /home/nabijaczleweli inherited from tarta-zoot
tarta-zoot/home/nabijaczleweli/tftp mountpoint /home/nabijaczleweli/tftp inherited from tarta-zoot
tarta-zoot/home/root mountpoint /root local
after:
$ zfs get mountpoint tarta-zoot -r
NAME PROPERTY VALUE SOURCE
tarta-zoot mountpoint / local
tarta-zoot/PAGEFILE.SYS mountpoint - -
tarta-zoot/etc mountpoint /etc inherited from tarta-zoot
tarta-zoot/home mountpoint /home inherited from tarta-zoot
tarta-zoot/home/xspon mountpoint /home/xspon inherited from tarta-zoot
tarta-zoot/home/nabijaczleweli mountpoint /home/nabijaczleweli inherited from tarta-zoot
tarta-zoot/home/nabijaczleweli/tftp mountpoint /home/nabijaczleweli/tftp inherited from tarta-zoot
tarta-zoot/home/root mountpoint /root local
Fixes: be8e1d81bf ("Flex
non-pretty-printed properties and raw-/pretty-print remaining ones")
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13286
->readpages was removed and replaced by ->readahead. Define
zpl_readahead for kernels that don't have ->readpages.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Riccardo Schirone <rschirone91@gmail.com>
Closes#13278
NDF_ONLY_PNBUF has been removed from FreeBSD in favor of NDFREE_PNBUF.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#13277
Bypass check of ZFS aces if the ACL is trivial. When an ACL is
trivial its permissions are represented by the mode without any
loss of information. In this case, it is safe to convert the
access request into equivalent mode and then pass desired mask
and inode to generic_permission(). This has the added benefit
of also checking whether entries in a POSIX ACL on the file grant
the desired access.
This commit also skips the ACL check on looking up the xattr dir
since such restrictions don't exist in Linux kernel and it makes
xattr lookup behavior inconsistent between SA and file-based
xattrs. We also don't want to perform a POSIX ACL check while
looking up the POSIX ACL if for some reason it is located in
the xattr dir rather than an SA.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Andrew Walker <awalker@ixsystems.com>
Closes#13237
The argument type of rw_destroy is (krwlock_t *) while currently
krwlock_t is passed in zfs_ctldir.c. This error is hidden because
rw_destroy is defined as ((void) 0) in linux. But anyway, this
mismatch should be fixed.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ping Huang <huangping@smartx.com>
Closes#13272
When HAVE_BLKDEV_GET_ERESTARTSYS is defined, compiler will complain
"defined but not used" warning for zvol_open_timeout_ms.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ping Huang <huangping@smartx.com>
Closes#13270
blkdev.h includes genhd.h since dawn of upstream git, so this is
globally safe
Upstream-commit: 322cbb50de711814c42fb088f6d31901502c711a ("block:
remove genhd.h")
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13251
bio_alloc(gfp_t gfp_mask, unsigned short nr_iovecs)
became
bio_alloc(struct block_device *bdev, unsigned short nr_vecs,
unsigned int opf, gfp_t gfp_mask)
passing NULL/0 continues previous behaviour
Upstream-commit: 07888c665b405b1cd3577ddebfeb74f4717a84c4 ("block:
pass a block_device and opf to bio_alloc")
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13251
Parts of the Linux kernel build system struggle with _Noreturn. This
results in the following warnings when building on RHEL 8.5, and likely
other environments. Switch to using the __attribute__((noreturn)).
warning: objtool: dbuf_free_range()+0x2b8:
return with modified stack frame
warning: objtool: dbuf_free_range()+0x0:
stack state mismatch: cfa1=7+40 cfa2=7+8
...
WARNING: EXPORT symbol "arc_buf_size" [zfs.ko] version generation
failed, symbol will not be versioned.
WARNING: EXPORT symbol "spa_open" [zfs.ko] version generation
failed, symbol will not be versioned.
...
Additionally, __thread_exit() has been renamed spl_thread_exit() and
made a static inline function. This was needed because the kernel
will generate a warning for symbols which are __attribute__((noreturn))
and then exported with EXPORT_SYMBOL.
While we could continue to use _Noreturn in user space I've also
switched it to __attribute__((noreturn)) purely for consistency
throughout the code base.
Reviewed-by: Ryan Moeller <freqlabs@FreeBSD.org>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13238
This explodes as -Wunused-variable on GCC 8.5.0, despite it being used,
just not in an evaluated context
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Ryan Moeller <freqlabs@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13195
This PR changes ZFS ACL checks to evaluate
fsuid / fsgid rather than euid / egid to avoid
accidentally granting elevated permissions to
NFS clients.
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Andrew Walker <awalker@ixsystems.com>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#13221
At shutdown time, we drain all of the zevents and set the
ZEVENT_SHUTDOWN flag. On FreeBSD, we may end up calling
zfs_zevent_destroy() after the zevent_lock has been destroyed while
the sysevent thread is winding down; we observe ESHUTDOWN, then back
out.
Events have already been drained, so just inline the kmem_free call in
sysevent_worker() to avoid the race, and document the assumption that
zfs_zevent_destroy doesn't do anything else useful at that point.
This fixes a panic that can occur at module unload time.
Reviewed-by: Ryan Moeller <freqlabs@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Kyle Evans <kevans@FreeBSD.org>
Closes#13220
bcopy() has a confusing argument order and is actually a move, not a
copy; they're all deprecated since POSIX.1-2001 and removed in -2008,
and we shim them out to mem*() on Linux anyway
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12996
On some architectures ZERO_PAGE is unavailable because it references
a GPL exported symbol of empty_zero_page. Originally e08b993 removed
the call to PAGE_ZERO(0) for assignment to the abd_zero_page. However,
a simple check can be done to avoid a kernel allocation and free for
the abd_zero_page if ZERO_PAGE is available.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Brian Atkinson <batkinson@lanl.gov>
Closes#13199
Caught by UBSAN: ZI_NO_DVA is passed explicitly in
zio_handle_decrypt_injection() and can be an ENOENT from zio_match_dva()
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Damian Szuberski <szuberskidamian@gmail.com>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13146Closes#13190
Add physical device size/capacity only for physical devices in
'zpool list -v' instead of displaying "-" in the SIZE column.
This would make it easier to see the individual device capacity and
to determine which spares are large enough to replace which devices.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Dipak Ghosh <dipak.ghosh@hpe.com>
Signed-off-by: Akash B <akash-b@hpe.com>
Closes#12561Closes#13106
Cleanup the kernel SIMD code by removing kernel dependencies.
- Replace XSTATE_XSAVE with our own XSAVE implementation for all
kernels not exporting kernel_fpu{begin,end}(), see #13059
- Replace union fpregs_state by a uint8_t * buffer and get the size
of the buffer from the hardware via the CPUID instruction
- Replace kernels xgetbv() by our own implementation which was
already there for userspace.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Attila Fülöp <attila@fueloep.org>
Closes#13102
When unlinking multiple files from a pool at 100% capacity, it was
possible for ENOSPC to be returned after the first unlink. e.g.
rm -f /mnt/fs/test1.0.0 /mnt/fs/test1.1.0 /mnt/fs/test1.2.0
rm: cannot remove '/mnt/fs/test1.1.0': No space left on device
rm: cannot remove '/mnt/fs/test1.2.0': No space left on device
After waiting for the pending deferred frees from the first unlink to
be processed the remaining files can then be unlinked. This is caused
by the quota limit in dsl_dir_tempreserve_impl() being temporarily
decreased to the allocatable pool capacity less any deferred free
space.
This is resolved using the existing mechanism of returning ERESTART
when over quota as long as we know enough space will shortly be
available after processing the pending deferred frees.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <freqlabs@FreeBSD.org>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13172
ZFS allows to update and retrieve additional file level attributes for
FreeBSD. This commit allows additional file level attributes to be
updated and retrieved for Linux. These include the flags stored in the
upper half of z_pflags only.
Two new IOCTLs have been added for this purpose. ZFS_IOC_GETDOSFLAGS
can be used to retrieve the attributes, while ZFS_IOC_SETDOSFLAGS can
be used to update the attributes.
Attributes that are allowed to be updated include ZFS_IMMUTABLE,
ZFS_APPENDONLY, ZFS_NOUNLINK, ZFS_ARCHIVE, ZFS_NODUMP, ZFS_SYSTEM,
ZFS_HIDDEN, ZFS_READONLY, ZFS_REPARSE, ZFS_OFFLINE and ZFS_SPARSE.
Flags can be or'd together while calling ZFS_IOC_SETDOSFLAGS.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Umer Saleem <usaleem@ixsystems.com>
Closes#13118
A function that returns with no value is a different thing from a
function that doesn't return at all. Those are two orthogonal
concepts, commonly confused.
pthread_create(3) expects a pointer to a start routine that has a
very precise prototype:
void *(*start_routine)(void *);
However, other thread functions, such as kernel ones, expect:
void (*start_routine)(void *);
Providing a different one is incorrect, and has only been working
because the ABIs happen to produce a compatible function.
We should use '_Noreturn void', since it's the natural type, and
then provide a '_Noreturn void *' wrapper for pthread functions.
For consistency, replace most cases of __NORETURN or
__attribute__((noreturn)) by _Noreturn. _Noreturn is understood
by -std=gnu89, so it should be safe to use everywhere.
Ref: https://github.com/openzfs/zfs/pull/13110#discussion_r808450136
Ref: https://software.codidact.com/posts/285972
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Signed-off-by: Alejandro Colomar <alx.manpages@gmail.com>
Closes#13120
Before this, /all/ numerical properties 1 (ZFS_PROP_CREATION,
ZPOOL_PROP_SIZE, VDEV_PROP_CAPACITY) would be non-fixed and
/all/ numerical properties 5 (ZFS_PROP_COMPRESSRATIO,
ZPOOL_PROP_HEALTH, VDEV_PROP_PSIZE) would be 8-wide
Realistically, this doesn't appear to be much of a problem
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13125
It's much nicer to import from upstream this way, and compiles
faster too.
Everything in lib/ is unmodified 1.4.5.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12978
As such, there are no specific synchronous semantics defined for
the xattrs. But for xattr=on, it does log to ZIL and zil_commit() is
done, if sync=always is set on dataset. This provides sync semantics
for xattr=on with sync=always set on dataset.
For the xattr=sa implementation, it doesn't log to ZIL, so, even with
sync=always, xattrs are not guaranteed to be synced before xattr call
returns to caller. So, xattr can be lost if system crash happens, before
txg carrying xattr transaction is synced.
This change adds xattr=sa logging to ZIL on xattr create/remove/update
and xattrs are synced to ZIL (zil_commit() done) for sync=always.
This makes xattr=sa behavior similar to xattr=on.
Implementation notes:
The actual logging is fairly straight-forward and does not warrant
additional explanation.
However, it has been 14 years since we last added new TX types
to the ZIL [1], hence this is the first time we do it after the
introduction of zpool features. Therefore, here is an overview of the
feature activation and deactivation workflow:
1. The feature must be enabled. Otherwise, we don't log the new
record type. This ensures compatibility with older software.
2. The feature is activated per-dataset, since the ZIL is per-dataset.
3. If the feature is enabled and dataset is not for zvol, any append to
the ZIL chain will activate the feature for the dataset. Likewise
for starting a new ZIL chain.
4. A dataset that doesn't have a ZIL chain has the feature deactivated.
We ensure (3) by activating on the first zil_commit() after the feature
was enabled. Since activating the features requires waiting for txg
sync, the first zil_commit() after enabling the feature will be slower
than usual. The downside is that this is really a conservative
approximation: even if we never append a 'TX_SETSAXATTR' to the ZIL
chain, we pay the penalty for feature activation. The upside is that the
user is in control of when we pay the penalty, i.e., upon enabling the
feature.
We ensure (4) by hooking into zil_sync(), where ZIL destroy actually
happens.
One more piece on feature activation, since it's spread across
multiple functions:
zil_commit()
zil_process_commit_list()
if lwb == NULL // first zil_commit since zil_open
zil_create()
if no log block pointer in ZIL header:
if feature enabled and not active:
// CASE 1
enable, COALESCE txg wait with dmu_tx that allocated the
log block
else // log block was allocated earlier than this zil_open
if feature enabled and not active:
// CASE 2
enable, EXPLICIT txg wait
else // already have an in-DRAM LWB
if feature enabled and not active:
// this happens when we enable the feature after zil_create
// CASE 3
enable, EXPLICIT txg wait
[1] da6c28aaf6
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Christian Schwarz <christian.schwarz@nutanix.com>
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Reviewed-by: Ryan Moeller <freqlabs@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jitendra Patidar <jitendra.patidar@nutanix.com>
Closes#8768Closes#9078
New `zfs_type_t` value `ZFS_TYPE_INVALID` is introduced.
Variable initialization is now possible to make GCC happy.
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: szubersk <szuberskidamian@gmail.com>
Closes#12167Closes#13103
The default behavior where the serious ZFS errors cause FS thread to
stuck is very bad for some production scenario.
In some production scenarios (Linux), it is recommended to make real
kernel PANIC, where system can be rebooted by watchdog or kernel itself.
This patch enables coherent handling of spl_panic_halt parameter.
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Authored-by: Wojciech Nizinski <w.nizinski@grinn-global.com>
Signed-off-by: szubersk <szuberskidamian@gmail.com>
Closes#12120Closes#13109
Which produces a warning since uints are, by definition, >=0
Reviewed-by: Alejandro Colomar <alx.manpages@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13110
Raw sending from pool1/encrypted with ashift=9 to pool2/encrypted with
ashift=12 results to failure when mounting pool2/encrypted (Input/Output
error). Notably, the opposite, raw sending from a greater ashift to a
lower one does not fail.
This happens because zio_compress_write() falsely checks only
ZIO_FLAG_RAW_COMPRESS and not ZIO_FLAG_RAW_ENCRYPT which is also set in
encrypted raw send streams. In this case it rounds up the psize and if
not equal to the zio->io_size it modifies the block by zeroing out
the extra bytes. Because this happens in a SA attr. registration object
(type=46), the decryption fails upon mounting the filesystem, and zpool
status falsely reports an error.
Fix this by checking both ZIO_FLAG_RAW_COMPRESS and ZIO_FLAG_RAW_ENCRYPT
before deciding whether to zero-pad a block.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#13067Closes#13074
ZFS on Linux originally implemented xattr namespaces in a way that is
incompatible with other operating systems. On illumos, xattrs do not
have namespaces. Every xattr name is visible. FreeBSD has two
universally defined namespaces: EXTATTR_NAMESPACE_USER and
EXTATTR_NAMESPACE_SYSTEM. The system namespace is used for protected
FreeBSD-specific attributes such as MAC labels and pnfs state. These
attributes have the namespace string "freebsd:system:" prefixed to the
name in the encoding scheme used by ZFS. The user namespace is used
for general purpose user attributes and obeys normal access control
mechanisms. These attributes have no namespace string prefixed, so
xattrs written on illumos are accessible in the user namespace on
FreeBSD, and xattrs written to the user namespace on FreeBSD are
accessible by the same name on illumos.
Linux has several xattr namespaces. On Linux, ZFS encodes the
namespace in the xattr name for every namespace, including the user
namespace. As a consequence, an xattr in the user namespace with the
name "foo" is stored by ZFS with the name "user.foo" and therefore
appears on FreeBSD and illumos to have the name "user.foo" rather than
"foo". Conversely, none of the xattrs written on FreeBSD or illumos
are accessible on Linux unless the name happens to be prefixed with one
of the Linux xattr namespaces, in which case the namespace is stripped
from the name. This makes xattrs entirely incompatible between Linux
and other platforms.
We want to make the encoding of user namespace xattrs compatible across
platforms. A critical requirement of this compatibility is for xattrs
from existing pools from FreeBSD and illumos to be accessible by the
same names in the user namespace on Linux. It is also necessary that
existing pools with xattrs written by Linux retain access to those
xattrs by the same names on Linux. Making user namespace xattrs from
Linux accessible by the correct names on other platforms is important.
The handling of other namespaces is not required to be consistent.
Add a fallback mechanism for listing and getting xattrs to treat xattrs
as being in the user namespace if they do not match a known prefix.
Do not allow setting or getting xattrs with a name that is prefixed
with one of the namespace names used by ZFS on supported platforms.
Allow choosing between legacy illumos and FreeBSD compatibility and
legacy Linux compatibility with a new tunable. This facilitates
replication and migration of pools between hosts with different
compatibility needs.
The tunable controls whether or not to prefix the namespace to the
name. If the xattr is already present with the alternate prefix,
remove it so only the new version persists. By default the platform's
existing convention is used.
Reviewed-by: Christian Schwarz <christian.schwarz@nutanix.com>
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11919
These were all folded into a single kstat at
/proc/spl/kstat/kcf/NONAME_provider_stats
with no way to know which one it actually was,
and only the AES and SHA (so not Skein) ones were ever updated
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12901
They don't do anything except clogging up the AVL tree
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12901
It's the only one actually used
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12901
It only needs to be locked if dynamic changes can occur. They can't.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12901
We register all providers at once, before anything happens
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12901
This is currently twice the amount we actually have (sha[12], skein,
aes), and 512 * sizeof(void*) = 4096: 128x more than we need and a waste
of most of a page in the kernel address space
Plus, there's no need to actually allocate it dynamically: it's always
got a static size. Put it in .data
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12901
Add hooks for when spa is created, exported, activated and
deactivated. Used by macOS to attach iokit, and lock
kext as busy (to stop unloads).
Userland, Linux, and, FreeBSD have empty stubs.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Closes#12801
There are two codepaths than can dirty final TXGs:
1) If calling spa_export_common()->spa_unload()->
spa_unload_log_sm_flush_all() after the spa_final_txg is set, then
spa_sync()->spa_flush_metaslabs() may end up dirtying the final
TXGs. Then we have the following panic:
Call Trace:
<TASK>
dump_stack_lvl+0x46/0x62
spl_panic+0xea/0x102 [spl]
dbuf_dirty+0xcd6/0x11b0 [zfs]
zap_lockdir_impl+0x321/0x590 [zfs]
zap_lockdir+0xed/0x150 [zfs]
zap_update+0x69/0x250 [zfs]
feature_sync+0x5f/0x190 [zfs]
space_map_alloc+0x83/0xc0 [zfs]
spa_generate_syncing_log_sm+0x10b/0x2f0 [zfs]
spa_flush_metaslabs+0xb2/0x350 [zfs]
spa_sync_iterate_to_convergence+0x15a/0x320 [zfs]
spa_sync+0x2e0/0x840 [zfs]
txg_sync_thread+0x2b1/0x3f0 [zfs]
thread_generic_wrapper+0x62/0xa0 [spl]
kthread+0x127/0x150
ret_from_fork+0x22/0x30
</TASK>
2) Calling vdev_*_stop_all() for a second time in spa_unload() after
spa_export_common() unnecessarily delays the final TXGs beyond what
spa_final_txg is set at.
Fix this by performing the check and call for
spa_unload_log_sm_flush_all() before the spa_final_txg is set in
spa_export_common(). Also check if the spa_final_txg has already been
set in spa_unload() and skip those calls in this case.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
External-issue: https://www.illumos.org/issues/9081Closes#13048Closes#13098
Unfortunately macOS has obj-C keyword "fallthrough" in the OS headers.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Damian Szuberski <szuberskidamian@gmail.com>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Closes#13097
On newer compilers, dsl_dataset.c now warns (or, on DEBUG, errors)
on uninitialized variable usage.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#13083
This allows reads/writes caused by accesses to mmap files to be
accounted correctly in the per-dataset kstats for both Linux and
FreeBSD.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <freqlabs@FreeBSD.org>
Signed-off-by: Matthias Blankertz <matthias@blankertz.org>
Closes#12994Closes#13044
dmu_recv_begin_check() unconditionally sets the DS_HOLD_FLAG_DECRYPT
flag before calling dsl_dataset_hold_flags(). If the key on the
receiving side isn't loaded or the send stream contains embedded
blocks, the receive check fails for a stream which is perfectly
valid and could be received without any problem. This seems like
a remnant of the initial design, where unencrypted datasets below
encrypted ones weren't allowed.
Add a condition to set `DS_HOLD_FLAG_DECRYPT` only for encrypted
datasets, modify an existing test to detect this regression and add
a test for raw replication streams.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Amanakis <gamanakis@gmail.com>
Co-authored-by: George Amanakis <gamanakis@gmail.com>
Signed-off-by: Attila Fülöp <attila@fueloep.org>
Closes#13033Closes#13076
To follow a change in illumos taskq
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Closes#12802
Currently, $(CC), $(LD), and $(LLVM) variables aren't passed to kbuild
while building modules. This causes modules to build with the default
GNU GCC toolchain and prevents experimenting with other toolchains such
as CLANG/LLVM. It can also lead to build failure if the CFLAGS/LDFLAGS
passed are incompatible with gcc/ld.
Pass $KERNEL_CC, $KERNEL_LD, and $KERNEL_LLVM as $(CC), $(LD), and
$(LLVM), respectively, to kbuild for each that is defined in the
environment. This should take care of the majority of alternative
toolchain use cases.
Reviewed-by: Damian Szuberski <szuberskidamian@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Peter Levine <plevine457@gmail.com>
Closes#13046
Linux 5.16 moved XSTATE_XSAVE and XSTATE_XRESTORE out of our reach,
so add our own XSAVE{,OPT,S} code and use it for Linux 5.16.
Please note that this differs from previous behavior in that it
won't handle exceptions created by XSAVE an XRSTOR. This is sensible
for three reasons.
- Exceptions during XSAVE and XRSTOR can only occur if the feature
is not supported or enabled or the memory operand isn't aligned
on a 64 byte boundary. If this happens something else went
terribly wrong, and it may be better to stop execution.
- Previously we just printed a warning and didn't handle the fault,
this is arguable for the above reason.
- All other *SAVE instruction also don't handle exceptions, so this
at least aligns behavior.
Finally add a test to catch such a regression in the future.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Attila Fülöp <attila@fueloep.org>
Closes#13042Closes#13059
All of these externs are already #included as static inline
functions via corresponding headers.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@gmail.com>
Closes#13073
There's no need to make the platform ops dynamic dispatch.
This change replaces the dynamic dispatch with static calls to the
platform-specific functions.
To avoid name collisions, prefix all platform-specific functions
with `zvol_os_`.
I actually find `zvol_..._os` slightly nicer to read in the calling
code, but having it as a prefix is useful.
Advantage:
- easier jump-to-definition / grepping
- potential benefits to static analysis
- better legibility
Future work: also prefix remaining `static` functions in zvol_os.c.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Christian Schwarz <christian.schwarz@nutanix.com>
Closes#12965
Use error thresholds from policy to control whether to scrub data
and/or metadata. If threshold is set to UINT64_MAX, then caller
probably does not care about result and we may skip that part.
By default import neither set the data error threshold nor read
the error counter, so skip the data scrub for faster import.
Metadata are still scrubbed and fail if even single error found.
While there just for symmetry return number of metadata errors in
case threshold is not set to zero and we haven't reached it.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#13022
The following commit moved the users of `deferred` into function
dsl_pool_unreserved_space:
commit d2734cce68
Author: Serapheim Dimitropoulos <serapheim.dimitro@delphix.com>
Date: Fri Dec 16 14:11:29 2016 -0800
OpenZFS 9166 - zfs storage pool checkpoint
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <freqlabs@FreeBSD.org>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Christian Schwarz <christian.schwarz@nutanix.com>
Closes#13056
POSIX requires that set-uid and set-gid bits to be removed when an
unprivileged user writes to a file and ZFS does that during normal
operation.
The problem arrises when the write is stored in the ZIL and replayed.
During replay we have no access to original credentials of the process
doing the write, so zfs_write() will be performed with the root
credentials. When root is doing the write set-uid and set-gid bits
are not removed from the file.
To correct that, log a separate TX_SETATTR entry that removed those bits
on first write to such file.
Idea from: Christian Schwarz
Add test for ZIL replay of setuid/setgid clearing.
Improve various edge cases when clearing setid bits:
- The setid bits can be readded during a single write, so make sure to check
for them on every chunk write.
- Log TX_SETATTR record at most once per transaction group (if the setid bits
are keep coming back).
- Move zfs_log_setattr() outside of zp->z_acl_lock.
Reviewed-by: Dan McDonald <danmcd@joyent.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Christian Schwarz <me@cschwarz.com>
Signed-off-by: Pawel Jakub Dawidek <pawel@dawidek.net>
Closes#13027
`configure` now accepts `--enable-asan` and `--enable-ubsan` switches
which results in passing `-fsanitize=address`
and `-fsanitize=undefined`, respectively, to the compiler. Those
flags are enabled in GitHub workflows for ZTS and zloop. Errors
reported by both instrumentations are corrected, except for:
- Memory leak reporting is (temporarily) suppressed. The cost of
fixing them is relatively high compared to the gains.
- Checksum computing functions in `module/zcommon/zfs_fletcher*`
have UBSan errors suppressed. It is completely impractical
to enforce 64-byte payload alignment there due to performance
impact.
- There's no ASan heap poisoning in `module/zstd/lib/zstd.c`. A custom
memory allocator is used there rendering that measure
unfeasible.
- Memory leaks detection has to be suppressed for `cmd/zvol_id`.
`zvol_id` is run by udev with the help of `ptrace(2)`. Tracing is
incompatible with memory leaks detection.
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: szubersk <szuberskidamian@gmail.com>
Closes#12928
In files created/modified before 4254acb there may be a corruption of
xattrs which is not reported during scrub and normal send/receive. It
manifests only as an error when raw sending/receiving. This happens
because currently only the raw receive path checks for discrepancies
between the dnode bonus length and the spill pointer flag.
In case we encounter a dnode whose bonus length is greater than the
predicted one, we should report an error. Modify in this regard
dnode_sync() with an assertion at the end, dump_dnode() to error out,
dsl_scan_recurse() to report errors during a scrub, and zstream to
report a warning when dumping. Also added a test to verify spill blocks
are sent correctly in a raw send.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#12720Closes#13014
69 CSTYLED BEGINs remain, appx. 30 of which can be removed if cstyle(1)
had a useful policy regarding
CALL(ARG1,
ARG2,
ARG3);
above 2 lines. As it stands, it spits out *both*
sysctl_os.c: 385: continuation line should be indented by 4 spaces
sysctl_os.c: 385: indent by spaces instead of tabs
which is very cool
Another >10 could be fixed by removing "ulong" &al. handling.
I don't foresee anyone actually using it intentionally
(does it even exist in modern headers? why did it in the first place?).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12993
First open locking changes were correctly applied to zvol_geom_open but
incorrectly applied to zvol_cdev_open, causing spa_namespace_lock to be
held indefinitely.
Make the first open locking in zvol_cdev_open match zvol_geom_open.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#13016
When using the two argument version of submit_bio() in kernel's prior
to 4.8 the first argument should be specified. It's used by block
dump to report the bio direction.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Finix Yan <yancw@info2soft.com>
Closes#13006
Linux 5.17 sees a rename from complete_and_exit()
to kthread complete_and_exit()
Upstream commit cead18552660702a4a46f58e65188fe5f36e9dfe
("exit: Rename complete_and_exit to kthread_complete_and_exit")
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12989
For us, I think it's always just FALLOC_FL_PUNCH_HOLE with a fake
mustache on.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Coleman Kane <ckane@colemankane.org>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12975
add_disk went from void to must-check int return.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Coleman Kane <ckane@colemankane.org>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12975
FreeBSD's implementation of zfs_uio_fault_move() returns EFAULT when a
page fault occurs while copying data in or out of user buffers. The VFS
treats such errors specially and will retry the I/O operation (which may
have made some partial progress).
When the FreeBSD and Linux implementations of zfs_write() were merged,
the handling of errors from dmu_write_uio_dbuf() changed such that
EFAULT is not handled as a partial write. For example, when appending
to a file, the z_size field of the znode is not updated after a partial
write resulting in EFAULT.
Restore the old handling of errors from dmu_write_uio_dbuf() to fix
this. This should have no impact on Linux, which has special handling
for EFAULT already.
Reviewed-by: Andriy Gapon <avg@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#12964
