For dedup, special and log devices "zpool add -n" does not print
correctly their vdev type:
~# zpool add -n pool dedup /tmp/dedup special /tmp/special log /tmp/log
would update 'pool' to the following configuration:
pool
/tmp/normal
/tmp/dedup
/tmp/special
/tmp/log
This could lead storage administrators to modify their ZFS pools to
unexpected and unintended vdev configurations.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#9783Closes#9390
The cleanup_devices function should remove any partitions created
on the device and force the partition table to be reread. This
is needed to ensure that blkid has an up to date version of what
devices and partitions are used by zfs.
The cleanup_devices call was removed from inuse_008_pos.ksh since
it operated on partitions instead of devices and was not needed.
Lastly ddidecode may be called by parted and was therefore added
to the constrained path.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9806
Replace `test -b` and equivalents with `is_disk_device`, so that `-c`
is used instead on FreeBSD which has no block cache layer for devices.
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#9795
Neither FreeBSD nor Linux support dumping to zvols.
DilOS still uses these tests, so the files are kept and the tests have
been relocated to sunos.run.
An `is_illumos` function was added to libtest.shlib to eliminate some
awkward platform checks.
A few functions that are not expected to be used outside of illumos
have been sanitized of extraneous FreeBSD adaptations.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#9794
The externally faulted vdev should be brought back online and have
its errors cleared before the pool is destroyed. Failure to do so
will leave a vdev with a valid active label. This vdev may then
not be used to create a new pool without the -f flag potentially
leading to subsequent test failures.
Additionally remove an unreachable log_pass from setup.ksh.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9777
Remove a few hardcoded instances of /var/tmp. This should use
the $TEST_BASE_DIR in order to allow the ZTS to be optionally
run in an alternate directory using `zfs-tests.sh -d <path>`.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9775
As of Python 3.5 the default behavior of json.tool was changed to
preserve the input order rather than lexical order. The test case
expects the output to be sorted so apply the --sort-keys option
to the json.tool command when using Python 3.5 and the option is
supported.
https://docs.python.org/3/library/json.html#module-json.tool
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9774
Update the devices_001_pos and devices_002_neg test cases such that the
special block device file created is backed by a ZFS volume. Specifying
a specific device allows the major and minor numbers to be easily
determined. Furthermore, this avoids the potentially dangerous behavior
of opening the first block device we happen to find under /dev/.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9773
Rather than defining a new instance of 'aok' in every compilation
unit which includes this header, there is a single instance
defined in zone.c, and the header now only declares an extern.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Paul Zuchowski <pzuchowski@datto.com>
Signed-off-by: Nick Black <dankamongmen@gmail.com>
Closes#9752
* large_dnode_008_pos - Force a pool sync before invoking zdb to
ensure the updated dnode blocks have been persisted to disk.
* refreserv_raidz - Wait for the /dev/zvol links to be both created
and removed, this is important because the same device volume
names are being used repeatedly.
* btree_test - Add missing .gitignore file for btree_test binary.
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9769
The pattern was not updated to match when the test output changed to
include a platform identifier for platform specific tests.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#9750
If the ZFS_COLOR env variable is set, then use ANSI color
output in zpool status:
- Column headers are bold
- Degraded or offline pools/vdevs are yellow
- Non-zero error counters and faulted vdevs/pools are red
- The 'status:' and 'action:' sections are yellow if they're
displaying a warning.
This also includes a new 'faketty' function in libtest.shlib that is
compatible with FreeBSD (code provided by @freqlabs).
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#9340
* devices_001_pos and devices_002_neg - Failing after FreeBSD ZTS
merged due to missing 'function' keyword for create_dev_file_linux.
* pool_state - Occasionally fails due to an insufficient delay
before checking 'zpool status'. Increasing the delay from 1 to 3
seconds resolved the issue in local testing.
* procfs_list_basic - Fails when run in-tree because the logged
command is actually 'lt-zfs'. Updated the regex accordingly.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9748
Additional test cases for the btree implementation, see #9181.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: John Kennedy <john.kennedy@delphix.com>
Closes#9717
Update the common ZTS scripts and individual test cases as needed
in order to allow them to be run on FreeBSD. The high level goal
is to provide compatibility wrappers whenever possible to minimize
changes to individual test cases.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#9692
Apply umask to `mode` which will eventually be applied to inode.
This is needed since VFS doesn't apply umask for O_TMPFILE files.
(Note that zpl_init_acl() applies `ip->i_mode &= ~current_umask();`
only when POSIX ACL is used.)
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@gmail.com>
Closes#8997Closes#8998
This interferes with zdb_read_block trying all the decompression
algorithms when the 'd' flag is specified, as some are
expected to fail. Also control the output when guessing
algorithms, try the more common compression types first, allow
specifying lsize/psize, and fix an uninitialized variable.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Zuchowski <pzuchowski@datto.com>
Closes#9612Closes#9630
The resilver restart test was reported as failing about 2% of the
time. Two issues were found:
- The event log wasn't large enough, so resilver events were missing
- One 'zpool sync' wasn't enough for resilver to start after zinject
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Signed-off-by: John Poduska <jpoduska@datto.com>
Issue #9588Closes#9677Closes#9703
This sets send_realloc_files.ksh to use properties.shlib
(like the other compression related tests)
It was missing from #9645
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Kjeld Schouten-Lebbing <kjeld@schouten-lebbing.nl>
Issue #9645Closes#9679
FreeBSD uses its own crypto framework in-kernel which, at this time,
has no EDONR implementation.
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Allan Jude <allanjude@freebsd.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#9664
FreeBSD requires three additional ioctls, they are ZFS_IOC_NEXTBOOT,
ZFS_IOC_JAIL, and ZFS_IOC_UNJAIL. These have been added after the
Linux-specific ioctls. The range 0x80-0xFF has been reserved for
future optional platform-specific ioctls. Any platform may choose
to implement these as appropriate.
None of the existing ioctl numbers have been changed to maintain
compatibility. For Linux no vectors have been registered for the
new ioctls and they are reported as unsupported.
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Allan Jude <allanjude@freebsd.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9667
- Moves compression algorithms for tests to properties.shlib
- Removes all compression algorithms levels from general tests
- Replaces on with lz4 for compression tests
- Removes random algorithm selection, if not needed
- Cleans copyright header formatting
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Signed-off-by: Kjeld Schouten-Lebbing <kjeld@schouten-lebbing.nl>
Closes#9645
There may be circumstances where it's desirable that all blocks
in a specified dataset be stored on the special device. Relax
the artificial 128K limit and allow the special_small_blocks
property to be set up to 1M. When blocks >1MB have been enabled
via the zfs_max_recordsize module option, this limit is increased
accordingly.
Reviewed-by: Don Brady <don.brady@delphix.com>
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9131Closes#9355
The `-o ashift` option must appear after attach to be properly
interpreted by getopt(3) on all platforms.
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Igor Kozhukhov <igor@dilos.org>
Closes#9636
If a device is participating in an active resilver, then it will have a
non-empty DTL. Operations like vdev_{open,reopen,probe}() can cause the
resilver to be restarted (or deferred to be restarted later), which is
unnecessary if the DTL is still covered by the current scan range. This
is similar to the logic in vdev_dtl_should_excise() where the DTL can
only be excised if it's max txg is in the resilvered range.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Gallagher <john.gallagher@delphix.com>
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Signed-off-by: John Poduska <jpoduska@datto.com>
Issue #840Closes#9155Closes#9378Closes#9551Closes#9588
The function zdb_read_block (zdb -R) was always intended to have a :c
flag which would read the DVA and length supplied by the user, and
display the checksum. Since we don't know which checksum goes with
the data, we should calculate and display them all.
For each checksum in the table, read in the data at the supplied
DVA:length, calculate the checksum, and display it. Update the man
page and create a zfs test for the new feature.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Signed-off-by: Paul Zuchowski <pzuchowski@datto.com>
Closes#9607
The tst.terminate_by_signal test case may occasionally fail when
running in a less consistent virtual environment. For all observed
failures the process was terminated correctly but it took longer than
expected resulting in too many snapshot being created.
To minimize the likelyhood of this occuring increase the threshold
from 50 to 90 snapshots. The larger limit will still verifiy that
the channel program was correctly terminated early.
Reviewed-by: Don Brady <don.brady@delphix.com>
Reviewed-by: Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9601
Use `printf` to properly interpret unicode characters.
Illumos uses a utility called `zlook` to allow additional flags to be
provided to readdir and lookup for testing. This functionality could
be ported to Linux, but even without it several of the tests can be
enabled by instead using the standard `test` command.
Additional, work is required to enable the remaining test cases.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Melikov <mail@gmelikov.ru>
Issue #7633Closes#8812
df58307 removed the need to specify -d 1 when zfs list and zfs get are
called with -t snapshot on a datset. This commit extends the same
behaviour to -t bookmark.
This commit also introduces the 'snap' shorthand for snapshots from
zfs list to zfs get.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Signed-off-by: InsanePrawn <insane.prawny@gmail.com>
Closes#9589
Reinstate the zpl_revalidate() functionality to resolve a regression
where dentries for open files during a rollback are not invalidated.
The unrelated functionality for automatically unmounting .zfs/snapshots
was not reverted. Nor was the addition of shrink_dcache_sb() to the
zfs_resume_fs() function.
This issue was not immediately caught by the CI because the test case
intended to catch it was included in the list of ZTS tests which may
occasionally fail for unrelated reasons. Remove all of the rollback
tests from this list to help identify the frequency of any spurious
failures.
The rollback_003_pos.ksh test case exposes a real issue with the
long standing code which needs to be investigated. Regardless,
it has been enable with a small workaround in the test case itself.
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Pavel Snajdr <snajpa@snajpa.net>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9587Closes#9592
The removal_with_errors.ksh test case could occasionally complete
the removal process instead of canceling due to an injected error.
To prevent this false positive, export and import the pool between
test phases to flush the ARC cache. Furthermore, double the amount
of data in the pool to increase the removal time.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9528
Currently, when you call 'zfs change-key' on an encrypted dataset
that has an unencrypted child, the code will trigger a VERIFY.
This VERIFY is leftover from before we allowed unencrypted
datasets to exist underneath encrypted ones. This patch fixes the
issue by simply replacing the VERIFY with an early return when
recursing through datasets.
Reviewed by: Jason King <jason.brian.king@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#9524
This change leverage module_param_call() to run arc_tuning_update()
immediately after the ARC tunable has been updated as suggested in
cffa8372 code review.
A simple test case is added to the ZFS Test Suite to prevent future
regressions in functionality.
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#9487Closes#9489
Tests that rely on special filesystems that are specific to Linux
should only be run on Linux.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <guss80@gmail.com>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#9512
Currently, incremental recursive encrypted receives fail to work
for any snapshot after the first. The reason for this is because
the check in zfs_setup_cmdline_props() did not properly realize
that when the user attempts to use '-x encryption' in this
situation, they are not really overriding the existing encryption
property and instead are attempting to prevent it from changing.
This resulted in an error message stating: "encryption property
'encryption' cannot be set or excluded for raw or incremental
streams".
This problem is fixed by updating the logic to expect this use
case.
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#9494
O_TMPFILE is not available on FreeBSD.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#9503
* Use .ksh extension for ksh scripts, not .sh
* Remove .ksh extension from tests in common.run
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#9502
With 4k disks, this test will fail in the last section because the
expected human readable value of 20.0M is reported as 20.1M. Rather than
use the human readable property, switch to the parsable property and
verify that the values are reasonably close.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: John Kennedy <john.kennedy@delphix.com>
Closes#9477
Not all versions of sed have the --in-place flag. Detect support for
the flag during ./configure and provide a fallback mechanism for those
systems where sed's behavior differs. The autoconf variable
${ac_inplace} can be used to choose the correct flags for editing a
file in place with sed.
Replace violating usages in Makefile.am with ${ac_inplace}.
Reviewed-by: Chris Dunlop <chris@onthe.net.au>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#9463
After commit 5e74ac51 which split and reordered the run files the
`zpool_status_-s` test began failing. The new ordering placed
the test after a previous test which used `zpool replace` to replace
a disk but did not clear its label. This resulted in the next test,
`zpool_status_-s`, failing because of the potentially active
pool being detected on the replaced vdev.
/dev/loop0 is part of potentially active pool 'testpool'
Use the default_mirror_setup_noexit() and default_cleanup_noexit()
functions to create the pool in `zpool_status_-s`. They use the -f
flag by default.
In the `scrub_after_resilver` test wipe the label during cleanup
to prevent future failures if the tests are again reordered.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9451
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#9445
Mostly whitespace changes, no functional changes intended.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#9447
When "feature@allocation_classes" is not enabled on the pool no vdev
with "special" or "dedup" allocation type should be allowed to exist in
the vdev tree.
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#9427Closes#9429
Tests that aren't limited to running on Linux can be moved to a common
runfile to be shared with other platforms.
The test runner and wrapper script are enhanced to allow specifying
multiple runfiles as a comma-separated list. The default runfiles are
now "common.run,PLATFORM.run" where PLATFORM is determined at run time.
Sections in runfiles that share a path with another runfile can append
a colon separator and an identifier to the path in the section
name, ie `[tests/functional/atime:Linux]`, to avoid overriding the tests
specified by other runfiles.
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#9391
Correctly use the `mntpnt_fs` variable, and include additional
logic to ensure the /etc/hostid is correct set up and cleaned up.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Igor Kozhukhov <igor@dilos.org>
Closes#9349
There have been occasional CI failures which occur when the trimmed
vdev size exactly matches the target size. Resolve this by slightly
relaxing the conditional and checking for -ge rather than -gt. In
all of the cases observer, the values match exactly. For example:
Failure /mnt/trim-vdev1 is 768 MB which is not -gt than 768 MB
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9399
Update cleanup_upgrade to use destroy_dataset and destroy_pool
when performing cleanup. These wrappers retry if the pool is busy
preventing occasional failures like those observed when running
tests upgrade_readonly_pool. For example:
SUCCESS: test enabled == enabled
User accounting upgrade is not executed on readonly pool
NOTE: Performing local cleanup via log_onexit (cleanup_upgrade)
cannot destroy 'testpool': pool is busy
ERROR: zpool destroy testpool exited 1
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9400
Factor Linux specific pieces out of libspl.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Sean Eric Fagan <sef@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9336
Refactor the zfs ioctls in to platform dependent and independent bits.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Sean Eric Fagan <sef@ixsystems.com>
Signed-off-by: Matthew Macy <mmacy@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#9301
Currently, the recv_fix_encryption_hierarchy() function accepts
'destsnap' as one of its parameters. Originally, this was intended
to be the top-level dataset of a receive (whether or not the
receive was recursive). Unfortunately, this parameter actually is
simply the input that is passed in from the command line. When
the user specifies 'zfs recv -d', this string is actually only the
name of the receiving pool since the rest of the name is derived
from the send stream. This causes the function to fail, leaving
some datasets with an invalid encryption hierarchy.
This patch resolves this problem by passing in the top_zfs variable
instead. In order to make this work, this patch also includes some
changes that ensure the value is always present when we need it.
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#9273Closes#9309
