Callbacks provided for module parameters are executed both
after the module is loaded, when a user alters it via sysfs, e.g
echo bar > /sys/modules/zfs/parameters/foo
as well as when the module is loaded with an argument, e.g.
modprobe zfs foo=bar
In the latter case, the init functions likely have not run yet,
including spa_init() which initializes the namespace lock so it is safe
to use.
Instead of immediately taking the namespace lock and attemping to
iterate over initialized spa structures, check whether spa_mode_global
is nonzero. This is set by spa_init() after it has initialized the
namespace lock.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#7496Closes#7521
Problem
=======
When we fail to open or import a storage pool, we typically don't
get any additional diagnostic information, just "no pool found" or
"can not import".
While there may be no additional user-consumable information, we should
at least make this situation easier to debug/diagnose for developers
and support. For example, we could start by using `zfs_dbgmsg()`
to log each thing that we try when importing, and which things
failed. E.g. "tried uberblock of txg X from label Y of device Z". Also,
we could log each of the stages that we go through in `spa_load_impl()`.
Solution
========
Following the cleanup to `spa_load_impl()`, debug messages have been
added to every point of failure in that function. Additionally,
debug messages have been added to strategic places, such as
`vdev_disk_open()`.
Authored by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Andrew Stormont <andyjstormont@gmail.com>
Approved by: Dan McDonald <danmcd@joyent.com>
Ported-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Tim Chase <tim@chase2k.com>
OpenZFS-issue: https://illumos.org/issues/8961
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/418079e0Closes#7459
OpenZFS 7614 - zfs device evacuation/removal
OpenZFS 9064 - remove_mirror should wait for device removal to complete
This project allows top-level vdevs to be removed from the storage pool
with "zpool remove", reducing the total amount of storage in the pool.
This operation copies all allocated regions of the device to be removed
onto other devices, recording the mapping from old to new location.
After the removal is complete, read and free operations to the removed
(now "indirect") vdev must be remapped and performed at the new location
on disk. The indirect mapping table is kept in memory whenever the pool
is loaded, so there is minimal performance overhead when doing operations
on the indirect vdev.
The size of the in-memory mapping table will be reduced when its entries
become "obsolete" because they are no longer used by any block pointers
in the pool. An entry becomes obsolete when all the blocks that use
it are freed. An entry can also become obsolete when all the snapshots
that reference it are deleted, and the block pointers that reference it
have been "remapped" in all filesystems/zvols (and clones). Whenever an
indirect block is written, all the block pointers in it will be "remapped"
to their new (concrete) locations if possible. This process can be
accelerated by using the "zfs remap" command to proactively rewrite all
indirect blocks that reference indirect (removed) vdevs.
Note that when a device is removed, we do not verify the checksum of
the data that is copied. This makes the process much faster, but if it
were used on redundant vdevs (i.e. mirror or raidz vdevs), it would be
possible to copy the wrong data, when we have the correct data on e.g.
the other side of the mirror.
At the moment, only mirrors and simple top-level vdevs can be removed
and no removal is allowed if any of the top-level vdevs are raidz.
Porting Notes:
* Avoid zero-sized kmem_alloc() in vdev_compact_children().
The device evacuation code adds a dependency that
vdev_compact_children() be able to properly empty the vdev_child
array by setting it to NULL and zeroing vdev_children. Under Linux,
kmem_alloc() and related functions return a sentinel pointer rather
than NULL for zero-sized allocations.
* Remove comment regarding "mpt" driver where zfs_remove_max_segment
is initialized to SPA_MAXBLOCKSIZE.
Change zfs_condense_indirect_commit_entry_delay_ticks to
zfs_condense_indirect_commit_entry_delay_ms for consistency with
most other tunables in which delays are specified in ms.
* ZTS changes:
Use set_tunable rather than mdb
Use zpool sync as appropriate
Use sync_pool instead of sync
Kill jobs during test_removal_with_operation to allow unmount/export
Don't add non-disk names such as "mirror" or "raidz" to $DISKS
Use $TEST_BASE_DIR instead of /tmp
Increase HZ from 100 to 1000 which is more common on Linux
removal_multiple_indirection.ksh
Reduce iterations in order to not time out on the code
coverage builders.
removal_resume_export:
Functionally, the test case is correct but there exists a race
where the kernel thread hasn't been fully started yet and is
not visible. Wait for up to 1 second for the removal thread
to be started before giving up on it. Also, increase the
amount of data copied in order that the removal not finish
before the export has a chance to fail.
* MMP compatibility, the concept of concrete versus non-concrete devices
has slightly changed the semantics of vdev_writeable(). Update
mmp_random_leaf_impl() accordingly.
* Updated dbuf_remap() to handle the org.zfsonlinux:large_dnode pool
feature which is not supported by OpenZFS.
* Added support for new vdev removal tracepoints.
* Test cases removal_with_zdb and removal_condense_export have been
intentionally disabled. When run manually they pass as intended,
but when running in the automated test environment they produce
unreliable results on the latest Fedora release.
They may work better once the upstream pool import refectoring is
merged into ZoL at which point they will be re-enabled.
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Alex Reece <alex@delphix.com>
Reviewed-by: George Wilson <george.wilson@delphix.com>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: Richard Laager <rlaager@wiktel.com>
Reviewed by: Tim Chase <tim@chase2k.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Garrett D'Amore <garrett@damore.org>
Ported-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Tim Chase <tim@chase2k.com>
OpenZFS-issue: https://www.illumos.org/issues/7614
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/f539f1ebCloses#6900
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: DHE <git@dehacked.net>
Closes#6672
generic_start_io_acct/generic_end_io_acct in the master
branch of the linux kernel requires that the request_queue
be provided.
Move the logic from freemem in the spl to arc_free_memory
in arc.c. Do this so we can take advantage of global_page_state
interface checks in zfs.
Upstream kernel replaced struct block_device with
struct gendisk in struct bio. Determine if the
function bio_set_dev exists during configure
and have zfs use that if it exists.
bio_set_dev https://github.com/torvalds/linux/commit/74d4699
global_node_page_state https://github.com/torvalds/linux/commit/75ef718
io acct https://github.com/torvalds/linux/commit/d62e26b
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#6635
Add a helper function to trim the tailing new line. While we're
here use this new hook to immediately apply the new scheduler.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#3356Closes#6573
Update many return and assignment statements to follow the convention
of using the SET_ERROR macro when returning a hard-coded non-zero
value from a function. This aids debugging by recording the error
codes in the debug log.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Ned Bass <bass6@llnl.gov>
Closes#6441
Commit torvalds/linux@4e4cbee9. The bio->bi_error field was
replaced with bio->bi_status which is an enum that describes
all possible error types.
Reviewed-by: Chunwei Chen <david.chen@osnexus.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6351
On a raidz vdev, a block that does not span all child vdevs, excluding
its skip sectors if any, may not be affected by a child vdev outage or
failure. In such cases, the block does not need to be resilvered.
However, current resilver algorithm simply resilvers all blocks on a
degraded raidz vdev. Such spurious IO is not only wasteful, but also
adds the risk of overwriting good data.
This patch eliminates such spurious IOs.
Reviewed-by: Gvozden Neskovic <neskovic@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Isaac Huang <he.huang@intel.com>
Closes#5316
Authored by: Hans Rosenfeld <hans.rosenfeld@nexenta.com>
Reviewed by: Dan Fields <dan.fields@nexenta.com>
Reviewed by: Alek Pinchuk <alek.pinchuk@nexenta.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Approved by: Dan McDonald <danmcd@omniti.com>
Reviewed-by: Don Brady <don.brady@intel.com>
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: George Melikov <mail@gmelikov.ru>
OpenZFS-issue: https://www.illumos.org/issues/7448
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/295438bCloses#5737
[bio] The req_op enum was changed to req_opf. Update the "Linux 4.8 API"
autotools checks to use an int to determine whether the various REQ_OP
values are defined. This should work properly on kernels >= 4.8.
[bio] bio_set_op_attrs() is now an inline function and can't be detected
with #ifdef. Add a configure check to determine whether bio_set_op_attrs()
is defined. Move the local definition of it from vdev_disk.c to
blkdev_compat.h for consistency with other related compability shims.
[bio] The read/write flags and their modifiers, including WRITE_FLUSH,
WRITE_FUA and WRITE_FLUSH_FUA have been removed from fs.h. Add the new
bio_set_flush() compatibility wrapper to replace VDEV_WRITE_FLUSH_FUA
and set the flags appropriately for each supported kernel version.
[vfs] The generic_readlink() function has been made static. If .readlink
in inode_operations is NULL, generic_readlink() is used.
[zol typo] Completely unrelated to 4.10 compat, fix a typo in the check
for REQ_OP_SECURE_ERASE so that the proper macro is defined:
s/HAVE_REQ_OP_SECURE_DISCARD/HAVE_REQ_OP_SECURE_ERASE/
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Chunwei Chen <david.chen@osnexus.com>
Signed-off-by: Tim Chase <tim@chase2k.com>
Closes#5499
Enable picky cstyle checks and resolve the new warnings. The vast
majority of the changes needed were to handle minor issues with
whitespace formatting. This patch contains no functional changes.
Non-whitespace changes are as follows:
* 8 times ; to { } in for/while loop
* fix missing ; in cmd/zed/agents/zfs_diagnosis.c
* comment (confim -> confirm)
* change endline , to ; in cmd/zpool/zpool_main.c
* a number of /* BEGIN CSTYLED */ /* END CSTYLED */ blocks
* /* CSTYLED */ markers
* change == 0 to !
* ulong to unsigned long in module/zfs/dsl_scan.c
* rearrangement of module_param lines in module/zfs/metaslab.c
* add { } block around statement after for_each_online_node
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Håkan Johansson <f96hajo@chalmers.se>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#5465
Without plugging, the default 'noop' scheduler will not merge
the BIOs which are part of a large ZIO.
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Isaac Huang <he.huang@intel.com>
Closes#5181
Non-Linux OpenZFS implementations require additional support to be
used a root pool. This code should simply be removed to avoid
confusion and improve readability.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Closes#4951
New REQ_OP_* definitions have been introduced to separate the
WRITE, READ, and DISCARD operations from the flags. This included
changing the encoding of bi_rw. It places REQ_OP_* in high order
bits and other stuff in low order bits. This encoding is done
through the new helper function bio_set_op_attrs. For complete
details refer to:
https://github.com/torvalds/linux/commit/f215082https://github.com/torvalds/linux/commit/4e1b2d5
Signed-off-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4892Closes#4899
The rw argument has been removed from submit_bio/submit_bio_wait.
Callers are now expected to set bio->bi_rw instead of passing it
in. See https://github.com/torvalds/linux/commit/4e49ea4a for
complete details.
Signed-off-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #4892
Issue #4899
Prior to b39c22b, which was first generally available in the 0.6.5
release as b39c22b, ZoL never actually submitted synchronous read or write
requests to the Linux block layer. This means the vdev_disk_dio_is_sync()
function had always returned false and, therefore, the completion in
dio_request_t.dr_comp was never actually used.
In b39c22b, synchronous ZIO operations were translated to synchronous
BIO requests in vdev_disk_io_start(). The follow-on commits 5592404 and
aa159af fixed several problems introduced by b39c22b. In particular,
5592404 introduced the new flag parameter "wait" to __vdev_disk_physio()
but under ZoL, since vdev_disk_physio() is never actually used, the wait
flag was always zero so the new code had no effect other than to cause
a bug in the use of the dio_request_t.dr_comp which was fixed by aa159af.
The original rationale for introducing synchronous operations in b39c22b
was to hurry certains requests through the BIO layer which would have
otherwise been subject to its unplug timer which would increase the
latency. This behavior of the unplug timer, however, went away during the
transition of the plug/unplug system between kernels 2.6.32 and 2.6.39.
To handle the unplug timer behavior on 2.6.32-2.6.35 kernels the
BIO_RW_UNPLUG flag is used as a hint to suppress the plugging behavior.
For kernels 2.6.36-2.6.38, the REQ_UNPLUG macro will be available and
ise used for the same purpose.
Signed-off-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4858
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Approved by: Dan McDonald <danmcd@omniti.com>
Ported by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/6531
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/97e8130
Porting notes:
- Added new IO delay tracepoints, and moved common ZIO tracepoint macros
to a new trace_common.h file.
- Used zio_delay_taskq() in place of OpenZFS's timeout_generic() function.
- Updated zinject man page
- Updated zpool_scrub test files
When ZFS partitions a block device it must wait for udev to create
both a device node and all the device symlinks. This process takes
a variable length of time and depends on factors such how many links
must be created, the complexity of the rules, etc. Complicating
the situation further it is not uncommon for udev to create and
then remove a link multiple times while processing the udev rules.
Given the above, the existing scheme of waiting for an expected
partition to appear by name isn't 100% reliable. At this point
udev may still remove and recreate think link resulting in the
kernel modules being unable to open the device.
In order to address this the zpool_label_disk_wait() function
has been updated to use libudev. Until the registered system
device acknowledges that it in fully initialized the function
will wait. Once fully initialized all device links are checked
and allowed to settle for 50ms. This makes it far more likely
that all the device nodes will exist when the kernel modules
need to open them.
For systems without libudev an alternate zpool_label_disk_wait()
was updated to include a settle time. In addition, the kernel
modules were updated to include retry logic for this ENOENT case.
Due to the improved checks in the utilities it is unlikely this
logic will be invoked. However, if the rare event it is needed
it will prevent a failure.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Richard Laager <rlaager@wiktel.com>
Closes#4523Closes#3708Closes#4077Closes#4144Closes#4214Closes#4517
Commit d1d7e2689d ("cstyle: Resolve C style issues") inverted
the logic on the none elevator comparison. Fix this and make it
cstyle warning clean.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4507
Currently, vdev_disk_physio_completion will try to wake up an waiter without
first checking the existence. This creates a race window in which complete is
called after dr is freed.
We add dr_wait in dio_request to indicate the existence of waiter. Also,
remove dr_rw since no one is using it, and reorder dr_ref to make the struct
more compact in 64bit.
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #3917
Issue #3880
Commit b39c22b set the READ_SYNC and WRITE_SYNC flags for a bio
based on the ZIO_PRIORITY_* flag passed in. This had the unnoticed
side-effect of making the vdev_disk_io_start() synchronous for
certain I/Os.
This in turn resulted in vdev_disk_io_start() being able to
re-dispatch zio's which would result in a RCU stalls when a disk
was removed from the system. Additionally, this could negatively
impact performance and explains the performance regressions reported
in both #3829 and #3780.
This patch resolves the issue by making the blocking behavior
dependent on a 'wait' flag being passed rather than overloading
the passed bio flags.
Finally, the WRITE_SYNC and READ_SYNC behavior is restricted to
non-rotational devices where there is no benefit to queuing to
aggregate the I/O.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #3652
Issue #3780
Issue #3785
Issue #3817
Issue #3821
Issue #3829
Issue #3832
Issue #3870
Commit torvalds/linux@4246a0b63b
("block: add a bi_error field to struct bio") dropped the error
argument from bio_endio in favor of newly introduced bio->bi_error.
This also replaces bio->bi_flags value BIO_UPTODATE.
bio_endio was a 3 argument function until Linux 2.6.24, which made it
a 2 argument function, and now the prototype has changed yet again to
a 1 argument function. Support for pre 2.6.24 kernels was already
dropped with 37f9dac592 ("zvol processing should use struct bio")
which assumed the 2 argument version in zvol_request(). Remaining code
to support the 3 argument version is hereby removed.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Issue #3799
Internally, zvols are files exposed through the block device API. This
is intended to reduce overhead when things require block devices.
However, the ZoL zvol code emulates a traditional block device in that
it has a top half and a bottom half. This is an unnecessary source of
overhead that does not exist on any other OpenZFS platform does this.
This patch removes it. Early users of this patch reported double digit
performance gains in IOPS on zvols in the range of 50% to 80%.
Comments in the code suggest that the current implementation was done to
obtain IO merging from Linux's IO elevator. However, the DMU already
does write merging while arc_read() should implicitly merge read IOs
because only 1 thread is permitted to fetch the buffer into ARC. In
addition, commercial ZFSOnLinux distributions report that regular files
are more performant than zvols under the current implementation, and the
main consumers of zvols are VMs and iSCSI targets, which have their own
elevators to merge IOs.
Some minor refactoring allows us to register zfs_request() as our
->make_request() handler in place of the generic_make_request()
function. This eliminates the layer of code that broke IO requests on
zvols into a top half and a bottom half. This has several benefits:
1. No per zvol spinlocks.
2. No redundant IO elevator processing.
3. Interrupts are disabled only when actually necessary.
4. No redispatching of IOs when all taskq threads are busy.
5. Linux's page out routines will properly block.
6. Many autotools checks become obsolete.
An unfortunate consequence of eliminating the layer that
generic_make_request() is that we no longer calls the instrumentation
hooks for block IO accounting. Those hooks are GPL-exported, so we
cannot call them ourselves and consequently, we lose the ability to do
IO monitoring via iostat. Since zvols are internally files mapped as
block devices, this should be okay. Anyone who is willing to accept the
performance penalty for the block IO layer's accounting could use the
loop device in between the zvol and its consumer. Alternatively, perf
and ftrace likely could be used. Also, tools like latencytop will still
work. Tools such as latencytop sometimes provide a better view of
performance bottlenecks than the traditional block IO accounting tools
do.
Lastly, if direct reclaim occurs during spacemap loading and swap is on
a zvol, this code will deadlock. That deadlock could already occur with
sync=always on zvols. Given that swap on zvols is not yet production
ready, this is not a blocker.
Signed-off-by: Richard Yao <ryao@gentoo.org>
The LBA weighting makes sense on rotational media where the outer tracks
have twice the bandwidth of the inner tracks. However, it is detrimental
on nonrotational media such as solid state disks, where the only effect
is to ensure that metaslabs enter the best-fit allocation behavior
sooner, which is detrimental to performance. It also makes no sense on
files where the underlying filesystem can arrange things however it
wants.
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#3712
Linux 4.2 commit torvalds/linux@dac5621 renamed bio->bi_cnt to
bio->__bi_cnt. Because this value is only used once in a block of
debug code it simplest just to remove the PANIC. To my knowledge
this debugging has never been hit or proved useful so this is no
great loss.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <ryao@gentoo.org>
Closes#3596
Translate zio requests with ZIO_PRIORITY_SYNC_READ and
ZIO_PRIORITY_SYNC_WRITE into synchronous bio requests by setting
READ_SYNC and WRITE_SYNC flags. Specifically, WRITE_SYNC flag turns
out to have a pronounced effect when writing to an SSD-based SLOG.
When WRITE_SYNC is not set (WRITE is set instead), the block trace
for a SLOG device looks as follows:
...
130,96 0 3 0.008968390 0 C W 830464 + 136 [0]
130,96 0 4 0.011999161 0 C W 830720 + 136 [0]
130,96 0 5 0.023955549 0 C W 831744 + 136 [0]
130,96 0 6 0.024337663 19775 A W 832000 + 136 <- (130,97) 829952
130,96 0 7 0.024338823 19775 Q W 832000 + 136 [z_wr_iss/6]
130,96 0 8 0.024340523 19775 G W 832000 + 136 [z_wr_iss/6]
130,96 0 9 0.024343187 19775 P N [z_wr_iss/6]
130,96 0 10 0.024344120 19775 I W 832000 + 136 [z_wr_iss/6]
130,96 0 11 0.026784405 0 UT N [swapper] 1
130,96 0 12 0.026805339 202 U N [kblockd/0] 1
130,96 0 13 0.026807199 202 D W 832000 + 136 [kblockd/0]
130,96 0 14 0.026966948 0 C W 832000 + 136 [0]
130,96 3 1 0.000449358 19788 A W 829952 + 136 <- (130,97) 827904
130,96 3 2 0.000450951 19788 Q W 829952 + 136 [z_wr_iss/19]
130,96 3 3 0.000453212 19788 G W 829952 + 136 [z_wr_iss/19]
130,96 3 4 0.000455956 19788 P N [z_wr_iss/19]
130,96 3 5 0.000457076 19788 I W 829952 + 136 [z_wr_iss/19]
130,96 3 6 0.002786349 0 UT N [swapper] 1
...
Here the 130,197 is the partition created on the log device when adding it
to the pool, whereas the base device is 130,96. As one can see, the writes
to the SLOG are not marked synchronous (the S is missing next to W), and
the queue unplugs occur based on the timer (UT event) resulting in slightly
over 2 msec latency of writes. This results in a sub-par performance of
single stream synchronous writes (limited by latency of the SLOG).
When the WRITE_SYNC is set, a similar trace looks as follows:
...
130,96 4 1 0.000000000 70714 A WS 4280576 + 136 <- (130,97) 4278528
130,96 4 2 0.000000832 70714 Q WS 4280576 + 136 [(null)]
130,96 4 3 0.000002109 70714 G WS 4280576 + 136 [(null)]
130,96 4 4 0.000003394 70714 P N [(null)]
130,96 4 5 0.000003846 70714 I WS 4280576 + 136 [(null)]
130,96 4 6 0.000004854 70714 D WS 4280576 + 136 [(null)]
130,96 5 1 0.000354487 70713 A WS 4280832 + 136 <- (130,97) 4278784
130,96 5 2 0.000355072 70713 Q WS 4280832 + 136 [(null)]
130,96 5 3 0.000356383 70713 G WS 4280832 + 136 [(null)]
130,96 5 4 0.000357635 70713 P N [(null)]
130,96 5 5 0.000358088 70713 I WS 4280832 + 136 [(null)]
130,96 5 6 0.000359191 70713 D WS 4280832 + 136 [(null)]
130,96 0 76 0.000159539 0 C WS 4280576 + 136 [0]
130,96 16 85 0.000742108 70718 A WS 4281088 + 136 <- (130,97) 4279040
130,96 16 86 0.000743197 70718 Q WS 4281088 + 136 [z_wr_iss/15]
130,96 16 87 0.000744450 70718 G WS 4281088 + 136 [z_wr_iss/15]
130,96 16 88 0.000745817 70718 P N [z_wr_iss/15]
130,96 16 89 0.000746705 70718 I WS 4281088 + 136 [z_wr_iss/15]
130,96 16 90 0.000747848 70718 D WS 4281088 + 136 [z_wr_iss/15]
130,96 0 77 0.000604063 0 C WS 4280832 + 136 [0]
130,96 0 78 0.000899858 0 C WS 4281088 + 136 [0]
As one can see, all the writes are synchronous (WS), and I/O completions
(e.g. from issue I to completion C) take 160-250 usec, or about 10x faster.
Since WRITE_SYNC or READ_SYNC flags are among several factors that are
considered when processing bio requests, it seems prudent to mark all the
zio requests of synchronous priority with the READ/WRITE_SYNC flags to make
them eligible for consideration as such by the Linux block I/O layer.
Signed-off-by: Boris Protopopov <boris.protopopov@actifio.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#3529
5027 zfs large block support
Reviewed by: Alek Pinchuk <pinchuk.alek@gmail.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Josef 'Jeff' Sipek <josef.sipek@nexenta.com>
Reviewed by: Richard Elling <richard.elling@richardelling.com>
Reviewed by: Saso Kiselkov <skiselkov.ml@gmail.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Dan McDonald <danmcd@omniti.com>
References:
https://www.illumos.org/issues/5027https://github.com/illumos/illumos-gate/commit/b515258
Porting Notes:
* Included in this patch is a tiny ISP2() cleanup in zio_init() from
Illumos 5255.
* Unlike the upstream Illumos commit this patch does not impose an
arbitrary 128K block size limit on volumes. Volumes, like filesystems,
are limited by the zfs_max_recordsize=1M module option.
* By default the maximum record size is limited to 1M by the module
option zfs_max_recordsize. This value may be safely increased up to
16M which is the largest block size supported by the on-disk format.
At the moment, 1M blocks clearly offer a significant performance
improvement but the benefits of going beyond this for the majority
of workloads are less clear.
* The illumos version of this patch increased DMU_MAX_ACCESS to 32M.
This was determined not to be large enough when using 16M blocks
because the zfs_make_xattrdir() function will fail (EFBIG) when
assigning a TX. This was immediately observed under Linux because
all newly created files must have a security xattr created and
that was failing. Therefore, we've set DMU_MAX_ACCESS to 64M.
* On 32-bit platforms a hard limit of 1M is set for blocks due
to the limited virtual address space. We should be able to relax
this one the ABD patches are merged.
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#354
5244 zio pipeline callers should explicitly invoke next stage
Reviewed by: Adam Leventhal <ahl@delphix.com>
Reviewed by: Alex Reece <alex.reece@delphix.com>
Reviewed by: Christopher Siden <christopher.siden@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Richard Elling <richard.elling@gmail.com>
Reviewed by: Dan McDonald <danmcd@omniti.com>
Reviewed by: Steven Hartland <killing@multiplay.co.uk>
Approved by: Gordon Ross <gwr@nexenta.com>
References:
https://www.illumos.org/issues/5244https://github.com/illumos/illumos-gate/commit/738f37b
Porting Notes:
1. The unported "2932 support crash dumps to raidz, etc. pools"
caused a merge conflict due to a copyright difference in
module/zfs/vdev_raidz.c.
2. The unported "4128 disks in zpools never go away when pulled"
and additional Linux-specific changes caused merge conflicts in
module/zfs/vdev_disk.c.
Ported-by: Richard Yao <richard.yao@clusterhq.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2828
By marking DMU transaction processing contexts with PF_FSTRANS
we can revert the KM_PUSHPAGE -> KM_SLEEP changes. This brings
us back in line with upstream. In some cases this means simply
swapping the flags back. For others fnvlist_alloc() was replaced
by nvlist_alloc(..., KM_PUSHPAGE) and must be reverted back to
fnvlist_alloc() which assumes KM_SLEEP.
The one place KM_PUSHPAGE is kept is when allocating ARC buffers
which allows us to dip in to reserved memory. This is again the
same as upstream.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
The initial port of ZFS to Linux required a way to identify virtual
memory to make IO to virtual memory backed slabs work, so kmem_virt()
was created. Linux 2.6.25 introduced is_vmalloc_addr(), which is
logically equivalent to kmem_virt(). Support for kernels before 2.6.26
was later dropped and more recently, support for kernels before Linux
2.6.32 has been dropped. We retire kmem_virt() in favor of
is_vmalloc_addr() to cleanup the code.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Mark the error handling branch as unlikely() because the current
kernel interface can never return NULL. However, we want to keep
the error handling in case this behavior changes in the futre.
Plus fix a small style issue.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Isaac Huang <he.huang@intel.com>
Closes#2703
4374 dn_free_ranges should use range_tree_t
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Max Grossman <max.grossman@delphix.com>
Reviewed by: Christopher Siden <christopher.siden@delphix.com
Reviewed by: Garrett D'Amore <garrett@damore.org>
Reviewed by: Dan McDonald <danmcd@omniti.com>
Approved by: Dan McDonald <danmcd@omniti.com>
References:
https://www.illumos.org/issues/4374https://github.com/illumos/illumos-gate/commit/bf16b11
Ported by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2531
Some network related block device uses tcp_sendpage, which doesn't
behave well when using 0-count page. Add assertion to catch them.
This has a runtime dependency on:
zfsonlinux/spl@ae16ed9 Fix crash when using ZFS on Ceph rbd
Signed-off-by: Chunwei Chen <tuxoko@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2277
bi_sector, bi_size and bi_idx are moved from bio to bio->bi_iter.
This patch creates BIO_BI_*(bio) macros to hide the differences.
Signed-off-by: Chunwei Chen <tuxoko@gmail.com>
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #2124
Userland tools such as blkid, grub2-probe and zdb will go through the
buffer cache. However, ZFS uses on submit_bio() to bypass the buffer
cache when performing IO operations on vdevs for efficiency purposes.
This permits the on-disk state and buffer cache to fall out of
synchronization. That causes seemingly random failures when tools
reading stale metadata from the buffer cache try to access references to
data that is no longer there.
A particularly bad failure this causes involves grub2-probe, which is
used by grub2-mkconfig. Ordinarily, a rootfs might be called
rpool/ROOT/gentoo. However, when a failure occurs in grub2-probe,
grub2-mkconfig will generate a configuration file containing
/ROOT/gentoo, which omits the pool name and causes a boot failure.
This is avoidable by calling invalidate_bdev() on each flush, which is a
simple way to ensure that all non-dirty pages are wiped. Since userland
tools rarely access vdevs directly, this should be a fancy noop >99.999%
of the time and have little impact on IO. We could have tried a finer
grained approach for the rare instances in which the vdevs are accessed
frequently by userland. However, that would require consideration of
corner cases and it is not worth the effort.
Memory-wise, it would have been better to use a Linux kernel API hook to
disable the buffer cache on such devices, but it provides us no way of
doing that, so we opt for this approach instead. We should revisit that
idea in the future when higher priority issues have been tackled.
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2150
The vast majority of these changes are in Linux specific code.
They are the result of not having an automated style checker to
validate the code when it was originally written. Others were
caused when the common code was slightly adjusted for Linux.
This patch contains no functional changes. It only refreshes
the code to conform to style guide.
Everyone submitting patches for inclusion upstream should now
run 'make checkstyle' and resolve any warning prior to opening
a pull request. The automated builders have been updated to
fail a build if when 'make checkstyle' detects an issue.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1821
3598 want to dtrace when errors are generated in zfs
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: Adam Leventhal <ahl@delphix.com>
Reviewed by: Christopher Siden <christopher.siden@delphix.com>
Approved by: Garrett D'Amore <garrett@damore.org>
References:
https://www.illumos.org/issues/3598illumos/illumos-gate@be6fd75a69
Ported-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #1775
Porting notes:
1. include/sys/zfs_context.h has been modified to render some new
macros inert until dtrace is available on Linux.
2. Linux-specific changes have been adapted to use SET_ERROR().
3. I'm NOT happy about this change. It does nothing but ugly
up the code under Linux. Unfortunately we need to take it to
avoid more merge conflicts in the future. -Brian
To avoid a potential deadlock when using a zvol as a swap
device prevent vdev_disk_io_flush() from performing IO during
the bio_alloc().
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1508
Reviewed by: Matt Ahrens <matthew.ahrens@delphix.com>
Reviewed by: Eric Schrock <eric.schrock@delphix.com>
Reviewed by: Christopher Siden <chris.siden@delphix.com>
Approved by: Garrett D'Amore <garrett@damore.org>
NOTES: This patch has been reworked from the original in the
following ways to accomidate Linux ZFS implementation
*) Usage of the cyclic interface was replaced by the delayed taskq
interface. This avoids the need to implement new compatibility
code and allows us to rely on the existing taskq implementation.
*) An extern for zfs_txg_synctime_ms was added to sys/dsl_pool.h
because declaring externs in source files as was done in the
original patch is just plain wrong.
*) Instead of panicing the system when the deadman triggers a
zevent describing the blocked vdev and the first pending I/O
is posted. If the panic behavior is desired Linux provides
other generic methods to panic the system when threads are
observed to hang.
*) For reference, to delay zios by 30 seconds for testing you can
use zinject as follows: 'zinject -d <vdev> -D30 <pool>'
References:
illumos/illumos-gate@283b84606bhttps://www.illumos.org/issues/3246
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1396
The issue with hot spares in ZoL is because it opens all leaf
vdevs exclusively (O_EXCL). On Linux, exclusive opens cause
subsequent exclusive opens to fail with EBUSY.
This could be resolved by not opening any of the devices
exclusively, which is what Illumos does, but the additional
protection offered by exclusive opens is desirable. It cleanly
prevents you from accidentally adding an in-use non-ZFS device
to your pool.
To fix this we very slightly relaxed the usage of O_EXCL in
the following ways.
1) Functions which open the device but only read had the
O_EXCL flag removed and were updated to use O_RDONLY.
2) A common holder was added to the vdev disk code. This
allow the ZFS code to internally open the device multiple
times but non-ZFS callers may not.
3) An exception was added to make_disks() for hot spare when
creating partition tables. For hot spare devices which
are already opened exclusively we skip creating the partition
table because this must already have been done when the disk
was originally added as a hot spare.
Additional minor changes include fixing check_in_use() to use
a partition instead of a slice suffix. And is_spare() was moved
above make_disks() to avoid adding a forward reference.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#250
As described by the comment and enforced the by assertion the
v->vdev_wholedisk will never be -1. The wholedisk handling
is performed by the user space utilities. To prevent confusion
this dead code is being removed.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
When vdev_disk.c was implemented for Linux we failed to handle the
reopen case. According to the vdev_reopen() comment leaf vdevs should
not be closed or opened when v->vdev_reopening is set. Under Linux
we would always close and open the device.
This issue was only noticed when a 'zpool scrub' command was run while
the leaf vdev device names in /dev/disk/by-vdev were missing. The
scrub command calls vdev_reopen() which caused the vdevs to be closed
but they couldn't be reopened due to the missing links. The result
was that all the vdevs were marked unavailable and the pool was
halted due to failmode=wait.
This patch adds the missing functionality in a similiar fashion to
to the Illumos code.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
To determine whether the kernel is capable of handling empty barrier
BIOs, we check for the presence of the bio_empty_barrier() macro,
which was introduced in 2.6.24. If this macro is defined, then we can
flush disk vdevs; if it isn't, then flushing is disabled.
Unfortunately, the bio_empty_barrier() macro was removed in 2.6.37,
even though the kernel is still capable of handling empty barrier BIOs.
As a result, flushing is effectively disabled on kernels >= 2.6.37,
meaning that starting from this kernel version, zfs doesn't use
barriers to guarantee on-disk data consistency. This is quite bad and
can lead to potential data corruption on power failures.
This patch fixes the issue by removing the configure check for
bio_empty_barrier(), as we don't support kernels <= 2.6.24 anymore.
Thanks to Richard Kojedzinszky for catching this nasty bug.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1318
As of Linux 3.4 the UMH_WAIT_* constants were renumbered. In
particular, the meaning of "1" changed from UMH_WAIT_PROC (wait for
process to complete), to UMH_WAIT_EXEC (wait for the exec, but not the
process). A number of call sites used the number 1 instead of the
constant name, so the behavior was not as expected on kernels with this
change.
One visible consequence of this change was that processes accessing
automounted snapshots received an ELOOP error because they failed to
wait for zfs.mount to complete.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#816
The current state of udev and devicer-mapper devices makes it difficult
to construct a mapping of DM partitions and their underlying DM device.
For example, with a /dev directory with the following contents:
$ ls -d /dev/dm-*
/dev/dm-0
/dev/dm-1
/dev/dm-2
/dev/dm-3
it is not immediately apparent if these are completely separate devices,
or partitions and real devices intermixed. In contrast, SCSI devices
would appear as so:
$ ls -d /dev/sd*
/dev/sda
/dev/sda1
/dev/sdb
/dev/sdb1
Here, one can immediately determine that there are two devices (sda and
sdb), each containing a single partition. The lack of a predictable and
consistent mapping from DM devices to DM device partitions makes it
difficult for user space to process these devices the same way it does
SCSI devices.
As a result, the ZFS utilities do not partition DM devices, and instead
set the "vdev_wholedisk" label to 0 and treat them as partitions. This
has the side effect that, even if ZFS has sole ownership of the device,
the IO scheduler will not be modified because it is treated as a
partition.
This change adds an exception for DM devices in vdev_elevator_switch,
allowing the elevator to be modified even though the "vdev_wholedisk"
property is not set.
Signed-off-by: Prakash Surya <surya1@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1149
