Authored by: George Wilson <george.wilson@delphix.com>
Reviewed by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Tom Caputi <tcaputi@datto.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported by: David Quigley <david.quigley@intel.com>
This review covers the reading and writing of compressed arc headers, sharing
data between the arc_hdr_t and the arc_buf_t, and the implementation of a new
dbuf cache to keep frequently access data uncompressed.
I've added a new member to l1 arc hdr called b_pdata. The b_pdata always hangs
off the arc_buf_hdr_t (if an L1 hdr is in use) and points to the physical block
for that DVA. The physical block may or may not be compressed. If compressed
arc is enabled and the block on-disk is compressed, then the b_pdata will match
the block on-disk and remain compressed in memory. If the block on disk is not
compressed, then neither will the b_pdata. Lastly, if compressed arc is
disabled, then b_pdata will always be an uncompressed version of the on-disk
block.
Typically the arc will cache only the arc_buf_hdr_t and will aggressively evict
any arc_buf_t's that are no longer referenced. This means that the arc will
primarily have compressed blocks as the arc_buf_t's are considered overhead and
are always uncompressed. When a consumer reads a block we first look to see if
the arc_buf_hdr_t is cached. If the hdr is cached then we allocate a new
arc_buf_t and decompress the b_pdata contents into the arc_buf_t's b_data. If
the hdr already has a arc_buf_t, then we will allocate an additional arc_buf_t
and bcopy the uncompressed contents from the first arc_buf_t to the new one.
Writing to the compressed arc requires that we first discard the b_pdata since
the physical block is about to be rewritten. The new data contents will be
passed in via an arc_buf_t (uncompressed) and during the I/O pipeline stages we
will copy the physical block contents to a newly allocated b_pdata.
When an l2arc is inuse it will also take advantage of the b_pdata. Now the
l2arc will always write the contents of b_pdata to the l2arc. This means that
when compressed arc is enabled that the l2arc blocks are identical to those
stored in the main data pool. This provides a significant advantage since we
can leverage the bp's checksum when reading from the l2arc to determine if the
contents are valid. If the compressed arc is disabled, then we must first
transform the read block to look like the physical block in the main data pool
before comparing the checksum and determining it's valid.
OpenZFS-issue: https://www.illumos.org/issues/6950
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/7fc10f0
Issue #5078
Several assignments to arc_c had no effect because it is ultimately
initialized to arc_c_max.
This aligns ZoL better with the upstream code which removed these
assignments some time ago.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tim Chase <tim@onlight.com>
Closes#5081
In case sav->sav_config was NULL the body of the function
would skip the iteration of the l2 cache devices and will
just cleanup the old devices. However, this wasn't very obvious
since the null check was performed after the loop body and after
the old devices were cleaned. Refactor the code so that it's now
obvious when the iteration of the l2cache devices is skipped.
This fixes the following cppcheck warning:
[module/zfs/spa.c:1552]: (error) Possible null pointer dereference: newvdevs
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Nikolay Borisov <n.borisov.lkml@gmail.com>
Closes#5087
Since they're allocated with spa_strdup(), they should be freed with
spa_strfree() so the proper length buffer is freed.
Reviewed-by: Richard Yao <ryao@gentoo.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tim Chase <tim@chase2k.com>
Closes#5082Closes#5086
This first phase brings over the ZFS SLM module, zfs_mod.c, to handle
auto operations in response to disk events. Disk event monitoring is
provided from libudev and generates the expected payload schema for
zfs_mod. This work leverages the recently added devid and phys_path
strings in the vdev label.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@intel.com>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#4673
These allocations can never fail. Leaving the error handling
code here gives the impression they can so it has been removed.
Signed-off-by: luozhengzheng <luo.zhengzheng@zte.com.cn>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#5048
perf: 2.75x faster ddt_entry_compare()
First 256bits of ddt_key_t is a block checksum, which are expected
to be close to random data. Hence, on average, comparison only needs to
look at first few bytes of the keys. To reduce number of conditional
jump instructions, the result is computed as: sign(memcmp(k1, k2)).
Sign of an integer 'a' can be obtained as: `(0 < a) - (a < 0)` := {-1, 0, 1} ,
which is computed efficiently. Synthetic performance evaluation of
original and new algorithm over 1G random keys on 2.6GHz Intel(R) Xeon(R)
CPU E5-2660 v3:
old 6.85789 s
new 2.49089 s
perf: 2.8x faster vdev_queue_offset_compare() and vdev_queue_timestamp_compare()
Compute the result directly instead of using conditionals
perf: zfs_range_compare()
Speedup between 1.1x - 2.5x, depending on compiler version and
optimization level.
perf: spa_error_entry_compare()
`bcmp()` is not suitable for comparator use. Use `memcmp()` instead.
perf: 2.8x faster metaslab_compare() and metaslab_rangesize_compare()
perf: 2.8x faster zil_bp_compare()
perf: 2.8x faster mze_compare()
perf: faster dbuf_compare()
perf: faster compares in spa_misc
perf: 2.8x faster layout_hash_compare()
perf: 2.8x faster space_reftree_compare()
perf: libzfs: faster avl tree comparators
perf: guid_compare()
perf: dsl_deadlist_compare()
perf: perm_set_compare()
perf: 2x faster range_tree_seg_compare()
perf: faster unique_compare()
perf: faster vdev_cache _compare()
perf: faster vdev_uberblock_compare()
perf: faster fuid _compare()
perf: faster zfs_znode_hold_compare()
Signed-off-by: Gvozden Neskovic <neskovic@gmail.com>
Signed-off-by: Richard Elling <richard.elling@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#5033
`zpool get guid,freeing,leaked` shows SOURCE as `default`, it should
be `-` as those props are not editable.
Changed code to not overwrite `src` for `ZPOOL_PROP_VERSION`, so it
stays `ZPROP_SRC_NONE`. Make src const to avoid future mistakes
Signed-off-by: Hajo Möller <dasjoe@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4170
zfsctl_snapdir_inactive is defined in zfs-0.6.3. In zfs-0.6.5.7
this is declaration remains even though the implementation was
removed in commit 278bee93. Removed fastreboot_disable_highpil
which is also unused.
Signed-off-by: caoxuewen cao.xuewen@zte.com.cn
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#5042
From user perspective, I would expect that ZFS is always able
to remove files and directories even when the quota is exceeded.
Authored by: Simon Klinkert <simon.klinkert@gmail.com>
Reviewed by: Dan McDonald <danmcd@omniti.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Ported-by: kernelOfTruth kerneloftruth@gmail.com
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/6940
OpenZFS-issue: https://www.illumos.org/issues/6334
OpenZFS-commit: https://github.com/illumos/illumos-gate/commit/9918916Closes#5044
For quite some time I was thinking about possibility to prefetch
ZFS indirection tables while doing sequential reads or writes.
Recent changes in predictive prefetcher made that much easier to
do. My tests on zvol with 16KB block size on 5x striped and 2x
mirrored pool of 10 disks show almost double throughput on sequential
read, and almost tripple on sequential rewrite. While for read alike
effect can be received from increasing maximal prefetch distance
(though at higher memory cost), for rewrite there is no other
solution so far.
Authored by: Alexander Motin <mav@freebsd.org>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Ported-by: kernelOfTruth kerneloftruth@gmail.com
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/6322
OpenZFS-commit: https://github.com/illumos/illumos-gate/commit/cb92f413Closes#5040
Porting notes:
- Change from upstream in module/zfs/dbuf.c in 'int dbuf_read' due
to commit 5f6d0b6 'Handle block pointers with a corrupt logical size'
- Difference from upstream in module/zfs/dmu_zfetch.c,
uint32_t zfetch_max_idistance -> unsigned int zfetch_max_idistance
- Variables have been initialized at the beginning of the function
(void dmu_zfetch) to resemble the order of occurrence and account
for C99, C11 mode errors.
In dbuf_dirty(), we need to grab the dn_struct_rwlock before looking at
the db_blkptr, to prevent it from being changed by syncing context.
Reviewed by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/7086
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/98fa317Closes#5039
ARC will evict meta buffers that exceed the arc_meta_limit. Before a further
investigating on whether we should take special protection on meta buffers,
this tunable make arc_meta_limit adjustable for different workloads.
People can set zfs_arc_meta_limit_percent to any value while insmod zfs.ko,
so some range check is added to guarantee a suitable arc_meta_limit.
Suggested by Tim Chase, zfs_arc_dnode_limit is changed to a percent-style
tunable as well.
Signed-off-by: GeLiXin <ge.lixin@zte.com.cn>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4957
As is the case with traverse_prefetch_thread(), the deep stacks caused
by traversal require disabling reclaim in the send traverse thread.
Also, do the same for receive_writer_thread() in which similar problems
have been observed.
Signed-off-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4912Closes#4998
API Change: Module parameter set/get methods take const parameter in
Grsecurity kernel v4.7.1
Signed-off-by: Gvozden Neskovic <neskovic@gmail.com>
Signed-off-by: Jason Zaman <jason@perfinion.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4997Closes#5001
Using a benchmark which has 32 threads creating 2 million files in the
same directory, on a machine with 16 CPU cores, I observed poor
performance. I noticed that dmu_tx_hold_zap() was using about 30% of
all CPU, and doing dnode_hold() 7 times on the same object (the ZAP
object that is being held).
dmu_tx_hold_zap() keeps a hold on the dnode_t the entire time it is
running, in dmu_tx_hold_t:txh_dnode, so it would be nice to use the
dnode_t that we already have in hand, rather than repeatedly calling
dnode_hold(). To do this, we need to pass the dnode_t down through
all the intermediate calls that dmu_tx_hold_zap() makes, making these
routines take the dnode_t* rather than an objset_t* and a uint64_t
object number. In particular, the following routines will need to have
analogous *_by_dnode() variants created:
dmu_buf_hold_noread()
dmu_buf_hold()
zap_lookup()
zap_lookup_norm()
zap_count_write()
zap_lockdir()
zap_count_write()
This can improve performance on the benchmark described above by 100%,
from 30,000 file creations per second to 60,000. (This improvement is on
top of that provided by working around the object allocation issue. Peak
performance of ~90,000 creations per second was observed with 8 CPUs;
adding CPUs past that decreased performance due to lock contention.) The
CPU used by dmu_tx_hold_zap() was reduced by 88%, from 340 CPU-seconds
to 40 CPU-seconds.
Sponsored by: Intel Corp.
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Ned Bass <bass6@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/7004
OpenZFS-commit: https://github.com/openzfs/openzfs/pull/109Closes#4641Closes#4972
zap_lockdir() / zap_unlockdir() should take a "void *tag" argument which
tags the hold on the zap. This will help diagnose programming errors
which misuse the hold on the ZAP.
Sponsored by: Intel Corp.
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Pavel Zakharov <pavel.zakha@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/7003
OpenZFS-commit: https://github.com/openzfs/openzfs/pull/108Closes#4972
When spa retry load succeeds and spa recovery is requested it may
leak in spa_load_best function. Always free the generated config
when it is not assigned to the spa.
Signed-off-by: cao.xuewen <cao.xuewen@zte.com.cn>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4940
This is another bug in the long line of hole-birth related issues. In
this particular case, it was discovered that a previous hole-birth fix
(illumos bug 6513, commit bc77ba73) did not cover as many cases as we
thought it did. While the issue worked in the case of hole-punching
(writing zeroes to a large part of a file), it did not deal with
truncation, and then writing beyond the new end of the file.
The problem is that dbuf_findbp will return ENOENT if the block it's
trying to find is beyond the end of the file. If that happens, we assume
there is no birth time, and so we lose that information when we write
out new blkptrs. We should teach dbuf_findbp to look for things that are
beyond the current end, but not beyond the absolute end of the file.
Authored by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Matthew Ahrens mahrens@delphix.com
Reviewed by: George Wilson george.wilson@delphix.com
Ported-by: kernelOfTruth <kerneloftruth@gmail.com>
Signed-off-by: Boris Protopopov <boris.protopopov@actifio.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/7176
OpenZFS-commit: https://github.com/openzfs/openzfs/pull/173/commits/8b9f3ad
Upstream-bugs: DLPX-46009
Porting notes:
- Fix ISO C90 mixed declaration error in dbuf.c ( int nlevels, epbs; ) ;
keep previous position of the initialization
Under a workload which makes heavy use of `dbuf_hold()`, I noticed that a
considerable amount of time was spent in `dbuf_hold_impl()`, due to its call to
`kmem_zalloc(sizeof (struct dbuf_hold_impl_data) * DBUF_HOLD_IMPL_MAX_DEPTH)`,
which is around 2KiB. This structure is used as a stack, to limit the size of
the C stack as dbuf_hold() calls itself recursively. We make a recursive call
to hold the parent's dbuf when the requested dbuf is not found. The vast
majority of the time, the parent or grandparent indirect dbuf is cached, so the
number of recursive calls is very low. However, we initialize this entire
array for every call to dbuf_hold().
To improve performance, this commit changes `dbuf_hold()` to use `kmem_alloc()`
instead of `kmem_zalloc()`. __dbuf_hold_impl_init is changed to initialize all
members of the struct before they are used. I observed ~5% performance
improvement on a workload which creates many files.
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4974
- Benchmark memory block is increased to 128kiB to reflect real block sizes more
accurately. Measurements include all three stages needed for checksum generation,
i.e. `init()/compute()/fini()`. The inner loop is repeated multiple times to offset
overhead of time function.
- Fastest implementation selects native and byteswap methods independently in
benchmark. To support this new function pointers `init_byteswap()/fini_byteswap()`
are introduced.
- Implementation mutex lock is replaced by atomic variable.
- To save time, benchmark is not executed in userspace. Instead, highest supported
implementation is used for fastest. Default userspace selector is still 'cycle'.
- `fletcher_4_native/byteswap()` methods use incremental methods to finish
calculation if data size is not multiple of vector stride (currently 64B).
- Added `fletcher_4_native_varsize()` special purpose method for use when buffer size
is not known in advance. The method does not enforce 4B alignment on buffer size, and
will ignore last (size % 4) bytes of the data buffer.
- Benchmark `kstat` is changed to match the one of vdev_raidz. It now shows
throughput for all supported implementations (in B/s), native and byteswap,
as well as the code [fastest] is running.
Example of `fletcher_4_bench` running on `Intel(R) Xeon(R) CPU E5-2660 v3 @ 2.60GHz`:
implementation native byteswap
scalar 4768120823 3426105750
sse2 7947841777 4318964249
ssse3 7951922722 6112191941
avx2 13269714358 11043200912
fastest avx2 avx2
Example of `fletcher_4_bench` running on `Intel(R) Xeon Phi(TM) CPU 7210 @ 1.30GHz`:
implementation native byteswap
scalar 1291115967 1031555336
sse2 2539571138 1280970926
ssse3 2537778746 1080016762
avx2 4950749767 1078493449
avx512f 9581379998 4010029046
fastest avx512f avx512f
Signed-off-by: Gvozden Neskovic <neskovic@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4952
Adds a module option which disables the hole_birth optimization
which has been responsible for several recent bugs, including
issue #4050.
Original-patch: https://gist.github.com/pcd1193182/2c0cd47211f3aee623958b4698836c48
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4833
Import a raidz pool which has a vdev with a bad label, zpool status
shows the right state of the dev, but the wrong state of the pool.
The pool state should be DEGRADED, not ONLINE.
We examine the label in vdev_validate while in spa_load_impl, the bad
label can be detected but doesn't propagate its state to the parent.
There are other chances to propagate state in the following vdev_load
if we failed to load DTL, but our pool is raidz1 which can tolerate a
faulted disk. So we lost the last chance to correct the pool state.
Propagate the leaf vdev's state to parent if its label was corrupted,
as is done elsewhere in vdev_validate.
Signed-off-by: GeLiXin <ge.lixin@zte.com.cn>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@intel.com>
Closes#4948
Authored by: Hans Rosenfeld <hans.rosenfeld@nexenta.com>
Reviewed by: Dan Fields <dan.fields@nexenta.com>
Reviewed by: Josef Sipek <josef.sipek@nexenta.com>
Reviewed by: Richard Elling <richard.elling@gmail.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Signed-off-by: Don Brady <don.brady@intel.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/5997
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/1437283
Porting Notes:
In addition to the OpenZFS changes this patch realigns the events
with those found in OpenZFS.
Events which would be logged as sysevents on illumos have been
been mapped to the 'sysevent' class for Linux. In addition, several
subclass names have been changed to match what is used in OpenZFS.
In all cases this means a '.' was changed to an '_' in the subclass.
The scripts provided by ZoL have been updated, however users which
provide scripts for any of the following events will need to rename
them based on the new subclass names.
ereport.fs.zfs.config.sync sysevent.fs.zfs.config_sync
ereport.fs.zfs.zpool.destroy sysevent.fs.zfs.pool_destroy
ereport.fs.zfs.zpool.reguid sysevent.fs.zfs.pool_reguid
ereport.fs.zfs.vdev.remove sysevent.fs.zfs.vdev_remove
ereport.fs.zfs.vdev.clear sysevent.fs.zfs.vdev_clear
ereport.fs.zfs.vdev.check sysevent.fs.zfs.vdev_check
ereport.fs.zfs.vdev.spare sysevent.fs.zfs.vdev_spare
ereport.fs.zfs.vdev.autoexpand sysevent.fs.zfs.vdev_autoexpand
ereport.fs.zfs.resilver.start sysevent.fs.zfs.resilver_start
ereport.fs.zfs.resilver.finish sysevent.fs.zfs.resilver_finish
ereport.fs.zfs.scrub.start sysevent.fs.zfs.scrub_start
ereport.fs.zfs.scrub.finish sysevent.fs.zfs.scrub_finish
ereport.fs.zfs.bootfs.vdev.attach sysevent.fs.zfs.bootfs_vdev_attach
Fix bugs due to kernel change in torvalds/linux@4bacc9c923 ("overlayfs:
Make f_path always point to the overlay and f_inode to the underlay").
This problem crashes system when use zfs as a layer of overlayfs.
Signed-off-by: Chen Haiquan <oc@yunify.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4914Closes#4935
The indefinite article before nvlist should be "an", not "a".
We have 27 "an nvlist" and 7 "a nvlist" in our comment, they should
stay the same as we are such a strict filesystem.
Signed-off-by: GeLiXin <ge.lixin@zte.com.cn>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4941
Non-Linux OpenZFS implementations require additional support to be
used a root pool. This code should simply be removed to avoid
confusion and improve readability.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Closes#4951
All users of bio->bi_rw have been replaced with compatibility wrappers.
This allows the kernel specific logic to be abstracted away, and for
each of the supported cases to be documented with the wrapper. The
updated interfaces are as follows:
* void blk_queue_set_write_cache(struct request_queue *, bool, bool)
* boolean_t bio_is_flush(struct bio *)
* boolean_t bio_is_fua(struct bio *)
* boolean_t bio_is_discard(struct bio *)
* boolean_t bio_is_secure_erase(struct bio *)
* VDEV_WRITE_FLUSH_FUA
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Closes#4951
This fix resolves warnings reported during compiling of user-space
libraries with different gcc optimization levels.
Tested with gcc versions: 4.9.2 (Debian), and 6.1.1 (Fedora).
The patch enables use of following opt levels: O0, O1, O2, O3, Og, Os, Ofast.
List of warnings:
[GCC 4.9.2 -Os]
libzfs_sendrecv.c:3726:26: error: 'clp' may be used uninitialized in this function [-Werror=maybe-uninitialized]
[GCC 4.9.2 -Og]
fs_fletcher.c:323:26: error: 'idx' may be used uninitialized in this function [-Werror=maybe-uninitialized]
dsl_dataset.c:1290:12: error: 'atp' may be used uninitialized in this function [-Werror=maybe-uninitialized]
[GCC 4.9.2 -Ofast]
u8_textprep.c:1310:9: error: 'tc[3ul]' may be used uninitialized in this function [-Werror=maybe-uninitialized]
u8_textprep.c:177:23: error: 'u8t[0ul]' may be used uninitialized in this function [-Werror=maybe-uninitialized]
dsl_dataset.c:2089:37: error: ‘hds’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
dsl_dataset.c:3216:2: error: ‘ds’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
dsl_dataset.c:1591:2: error: ‘ds’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
dsl_dataset.c:3341:2: error: ‘ds’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
vdev_raidz.c:1153:8: error: 'dcount[2]' may be used uninitialized in this function [-Werror=maybe-uninitialized]
vdev_raidz.c:1167:17: error: 'dst[2]' may be used uninitialized in this function [-Werror=maybe-uninitialized]
kernel.c:1005:2: error: ‘resid’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
libzfs_dataset.c:2826:8: error: ‘val’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
libzfs_dataset.c:3056:35: error: ‘val’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
libzfs_dataset.c:1584:13: error: ‘val’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
libzfs_dataset.c:3056:35: error: ‘val’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
libzfs_dataset.c:1792:66: error: ‘val’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
libzfs_dataset.c:3986:35: error: ‘val’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
[GCC 6.1.1]
Resolved in PR #4907
Signed-off-by: Gvozden Neskovic <neskovic@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4937
Starting from Linux 4.7, get_acl will set acl cache pointer to temporary
sentinel value before calling i_op->get_acl. Therefore we can't compare
against ACL_NOT_CACHED and return.
Since from Linux 3.14, get_acl already check the cache for us, so we
disable this in zpl_get_acl.
Linux 4.7 also does set_cached_acl for us so we disable it in zpl_get_acl.
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Signed-off-by: Nikolay Borisov <n.borisov.lkml@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4944Closes#4946
The posix_acl_valid() function has been updated to require a
user namespace. Filesystem callers should normally provide the
user_ns from the super block associcated with the ACL; the
zpl_posix_acl_valid() wrapper has been added for this purpose.
See https://github.com/torvalds/linux/commit/0d4d717f for
complete details.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Nikolay Borisov <n.borisov.lkml@gmail.com>
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Closes#4922
Remove ZFS_AC_KERNEL_CURRENT_UMASK and ZFS_AC_KERNEL_POSIX_ACL_CACHING
configure checks, all supported kernel provide this functionality.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Nikolay Borisov <n.borisov.lkml@gmail.com>
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Closes#4922
* When the uid/gid change is handled in zfs_setattr we want to
actually adjust the user passed uid to a KUID and write that to disk.
* In trace points use the i_uid member without doing translation,
since it has already been performed.
* Use kuid in zfs_aclset_common
Signed-off-by: Nikolay Borisov <n.borisov.lkml@gmail.com>
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4928
When arc_max is increased, arc_meta_limit will not be updated to 3/4
of the new arc_c_max value. This was done originally to preserve any
existing maximum value. This turned out to be counter intuitive to
users and this fix changes that behavior. If zfs_arc_meta_limit is
non-default, it will be picked up later in the ARC tuning function.
Signed-off-by: Gaurav Kumar <gaurav.kumar@nutanix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4893
As of gcc 6.1.1 20160621 (Red Hat 6.1.1-3) a self-comparison is
detected by gcc in metaslab_alloc(). Resolve the warning by passing
a physical size of 0 to BP_SET_BIRTH() as it done by other callers.
module/zfs/metaslab.c: In function ‘metaslab_alloc’:
module/zfs/metaslab.c:2575:184: error: self-comparison always evaluates
to true [-Werror=tautological-compare]
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Gvozden Neskovic <neskovic@gmail.com>
Issue #4907
Fix a possible VDEV statistics array overflow when ZIOs with
ZIO_PRIORITY_NOW complete.
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #4883Closes#4917
Currently i_blkbits is always set to SPA_MINBLOCKSHIFT every time
zfs_inode_update_impl is called. Since this value never changes
move its assignment to at inode creation time.
Signed-off-by: Nikolay Borisov <n.borisov.lkml@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4906
In zfs_ioc_log_history() function the tsd_set() function is called
with NULL which causes the zfs_allow_log_destroy() to be run. In
this case the passed value will be NULL. This is normally entirely
safe because strfree() maps directly to kfree() which may be passed
a NULL. However, since alternate implementations of strfree() may
not handle this gracefully add a check for NULL.
Observed under an embedded Linux 2.6.32.41 kernel running the
automated testing while running the ZFS Test Suite.
Signed-off-by: caoxuewen <cao.xuewen@zte.com.cn>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4872
New REQ_OP_* definitions have been introduced to separate the
WRITE, READ, and DISCARD operations from the flags. This included
changing the encoding of bi_rw. It places REQ_OP_* in high order
bits and other stuff in low order bits. This encoding is done
through the new helper function bio_set_op_attrs. For complete
details refer to:
https://github.com/torvalds/linux/commit/f215082https://github.com/torvalds/linux/commit/4e1b2d5
Signed-off-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4892Closes#4899
The rw argument has been removed from submit_bio/submit_bio_wait.
Callers are now expected to set bio->bi_rw instead of passing it
in. See https://github.com/torvalds/linux/commit/4e49ea4a for
complete details.
Signed-off-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #4892
Issue #4899
The memory allocation and locking in `spa_txg_history_*()` can
potentially block txg_hold_open for arbitrarily long periods of time.
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #4333
Here's the problem - on 4K native devices in userland on
Linux using O_DIRECT, buffers must be 4K aligned or I/O
will fail with EINVAL, causing zdb (and others) to coredump.
Since userland probably doesn't need optimized buffer caches,
we just force 4K alignment on everything.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Gvozden Neskovic <neskovic@gmail.com>
Closes#4479
DMU_MAX_ACCESS should be cast to a uint64_t otherwise the
multiplication of DMU_MAX_ACCESS with spa_asize_inflation will
be 32 bit and may lead to an overflow. Currently DMU_MAX_ACCESS
is 64 * 1024 * 1024, so spa_asize_inflation being 64 or more will
lead to an overflow.
Found by static analysis with CoverityScan 0.8.5
CID 150942 (#1 of 1): Unintentional integer overflow
(OVERFLOW_BEFORE_WIDEN)
overflow_before_widen: Potentially overflowing expression
67108864 * spa_asize_inflation with type int (32 bits, signed)
is evaluated using 32-bit arithmetic, and then used in a context
that expects an expression of type uint64_t (64 bits, unsigned).
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4889
Metadata-intensive workloads can cause the ARC to become permanently
filled with dnode_t objects as they're pinned by the VFS layer.
Subsequent data-intensive workloads may only benefit from about
25% of the potential ARC (arc_c_max - arc_meta_limit).
In order to help track metadata usage more precisely, the other_size
metadata arcstat has replaced with dbuf_size, dnode_size and bonus_size.
The new zfs_arc_dnode_limit tunable, which defaults to 10% of
zfs_arc_meta_limit, defines the minimum number of bytes which is desirable
to be consumed by dnodes. Attempts to evict non-metadata will trigger
async prune tasks if the space used by dnodes exceeds this limit.
The new zfs_arc_dnode_reduce_percent tunable specifies the amount by
which the excess dnode space is attempted to be pruned as a percentage of
the amount by which zfs_arc_dnode_limit is being exceeded. By default,
it tries to unpin 10% of the dnodes.
The problem of dnode metadata pinning was observed with the following
testing procedure (in this example, zfs_arc_max is set to 4GiB):
- Create a large number of small files until arc_meta_used exceeds
arc_meta_limit (3GiB with default tuning) and arc_prune
starts increasing.
- Create a 3GiB file with dd. Observe arc_mata_used. It will still
be around 3GiB.
- Repeatedly read the 3GiB file and observe arc_meta_limit as before.
It will continue to stay around 3GiB.
With this modification, space for the 3GiB file is gradually made
available as subsequent demands on the ARC are made. The previous behavior
can be restored by setting zfs_arc_dnode_limit to the same value as the
zfs_arc_meta_limit.
Signed-off-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #4345
Issue #4512
Issue #4773Closes#4858
Prior to b39c22b, which was first generally available in the 0.6.5
release as b39c22b, ZoL never actually submitted synchronous read or write
requests to the Linux block layer. This means the vdev_disk_dio_is_sync()
function had always returned false and, therefore, the completion in
dio_request_t.dr_comp was never actually used.
In b39c22b, synchronous ZIO operations were translated to synchronous
BIO requests in vdev_disk_io_start(). The follow-on commits 5592404 and
aa159af fixed several problems introduced by b39c22b. In particular,
5592404 introduced the new flag parameter "wait" to __vdev_disk_physio()
but under ZoL, since vdev_disk_physio() is never actually used, the wait
flag was always zero so the new code had no effect other than to cause
a bug in the use of the dio_request_t.dr_comp which was fixed by aa159af.
The original rationale for introducing synchronous operations in b39c22b
was to hurry certains requests through the BIO layer which would have
otherwise been subject to its unplug timer which would increase the
latency. This behavior of the unplug timer, however, went away during the
transition of the plug/unplug system between kernels 2.6.32 and 2.6.39.
To handle the unplug timer behavior on 2.6.32-2.6.35 kernels the
BIO_RW_UNPLUG flag is used as a hint to suppress the plugging behavior.
For kernels 2.6.36-2.6.38, the REQ_UNPLUG macro will be available and
ise used for the same purpose.
Signed-off-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4858
Remove duplicate z_uid/z_gid member which are also held in the
generic vfs inode struct. This is done by first removing the members
from struct znode and then using the KUID_TO_SUID/KGID_TO_SGID
macros to access the respective member from struct inode. In cases
where the uid/gids are being marshalled from/to disk, use the newly
introduced zfs_(uid|gid)_(read|write) functions to properly
save the uids rather than the internal kernel representation.
Signed-off-by: Nikolay Borisov <n.borisov.lkml@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #4685
Issue #227
Currently there is an issue where metaslab_fastwrite_unmark() unmarks
fastwrites on vdev_t's that have never had fastwrites marked on them.
The 'fastwrite mark' is essentially a count of outstanding bytes that
will be written to a vdev and is used in syncing context. The problem
stems from the fact that the vdev_pending_fastwrite field is not being
transferred over when replacing a top-level vdev. As a result, the
metaslab is marked for fastwrite on the old vdev and unmarked on the
new one, which brings the fastwrite count below zero. This fix simply
assigns vdev_pending_fastwrite from the old vdev to the new one so
this count is not lost.
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4267
When zfs_domount fails zsb will be freed, and its caller
mount_nodev/get_sb_nodev will do deactivate_locked_super and calls into
zfs_preumount.
In order to make sure we don't touch any nonexistent stuff, we must make sure
s_fs_info is NULL in the fail path so zfs_preumount can easily check that.
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4867
Issue #4854
Print table with speed of methods for each implementation.
Last line describes contents of [fastest] selection.
Signed-off-by: Gvozden Neskovic <neskovic@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4860
- Implementation lock replaced with atomic variable
- Trailing whitespace is removed from user specified parameter, to enhance
experience when using commands that add newline, e.g. `echo`
- raidz_test: remove dependency on `getrusage()` and RUSAGE_THREAD, Issue #4813
- silence `cppcheck` in vdev_raidz, partial solution of Issue #1392
- Minor fixes and cleanups
- Enable use of original parity methods in [fastest] configuration.
New opaque original ops structure, representing native methods, is added
to supported raidz methods. Original parity methods are executed if selected
implementation has NULL fn pointer.
Signed-off-by: Gvozden Neskovic <neskovic@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #4813
Issue #1392
Wait for iput_async before entering evict_inodes in
generic_shutdown_super. The reason we must finish before
evict_inodes is when lazytime is on, or when zfs_purgedir calls
zfs_zget, iput would bump i_count from 0 to 1. This would race
with the i_count check in evict_inodes. This means it could
destroy the inode while we are still using it.
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4854
It is possible that the given DS may have hidden child (%recv)
datasets - "leftovers" resulting from the previously interrupted
'zfs receieve'. Try to remove the hidden child (%recv) and after
that try to remove the target dataset. If the hidden child
(%recv) does not exist the original error (EEXIST) will be returned.
Signed-off-by: Roman Strashkin <roman.strashkin@nexenta.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4818
A mostly mechanical change, taking into account i_nlink is 32 bits vs ZFS's
64 bit on-disk link count.
We revert "xattr dir doesn't get purged during iput" (ddae16a) as this is a
more Linux-integrated fix for the same issue.
In addition, setting the initial link count on a new node has been changed
from setting one less than required in zfs_mknode() then incrementing to the
correct count in zfs_link_create() (which was somewhat bizarre in the first
place), to setting the correct count in zfs_mknode() and not incrementing it
in zfs_link_create(). This both means we no longer set the link count in
sa_bulk_update() twice (once for the initial incorrect count then again for
the correct count), as well as adhering to the Linux requirement of not
incrementing a zero link count without I_LINKABLE (see linux commit
f4e0c30c).
Signed-off-by: Chris Dunlop <chris@onthe.net.au>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Closes#4838
Issue #227
Dropping DBUF_HASH_MUTEX when walking the hash list is unsafe. The dbuf
can be freed at any time.
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4846
In arc_buf_info(), the arc_buf_t may have no header. If not, don't try
to fetch the arc buffer stats and instead just zero them.
The null dereferences were observed while accessing the dbuf kstat with
awk on a system in which millions of small files were being created in
order to overflow the system's metadata limit.
Signed-off-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Closes#4837
zfs_ioc_recv_impl() is changed to always allocate the 'errors'
nvlist, its callers are responsible for freeing it.
Signed-off-by: Gvozden Neskovic <neskovic@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4829
The following scenario can result in garbage in the dn_spill field.
The db->db_blkptr must be set to NULL when DNODE_FLAG_SPILL_BLKPTR
is clear to ensure the dn_spill field is cleared.
Current txg = A.
* A new spill buffer is created. Its dbuf is initialized with
db_blkptr = NULL and it's dirtied.
Current txg = B.
* The spill buffer is modified. It's marked as dirty in this txg.
* Additional changes make the spill buffer unnecessary because the
xattr fits into the bonus buffer, so it's removed. The dbuf is
undirtied in this txg, but it's still referenced and cannot be
destroyed.
Current txg = C.
* Starts syncing of txg A
* dbuf_sync_leaf() is called for the spill buffer. Since db_blkptr
is NULL, dbuf_check_blkptr() is called.
* The dbuf starts being written and it reaches the ready state
(not done yet).
* A new change makes the spill buffer necessary again.
sa_build_layouts() ends up calling dbuf_find() to locate the
dbuf. It finds the old dbuf because it has not been destroyed yet
(it will be destroyed when the previous write is done and there
are no more references). The old dbuf has db_blkptr != NULL.
* txg A write is complete and the dbuf released. However it's still
referenced, so it's not destroyed.
Current txg = D.
* Starts syncing of txg B
* dbuf_sync_leaf() is called for the bonus buffer. Its contents are
directly copied into the dnode, overwriting the blkptr area because,
in txg B, the bonus buffer was big enough to hold the entire xattr.
* At this point, the db_blkptr of the spill buffer used in txg C
gets corrupted.
Signed-off-by: Peng <peng.hse@xtaotech.com>
Signed-off-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#3937
zp->z_xattr_parent will pin the parent. This will cause huge issue
when unlink a file with xattr. Because the unlinked file is pinned, it
will never get purged immediately. And because of that, the xattr
stuff will never be marked as unlinked. So the whole unlinked stuff
will stay there until shrink cache or umount.
This change partially reverts e89260a. This is safe because only the
zp->z_xattr_parent optimization is removed, zpl_xattr_security_init()
is still called from the zpl outside the inode lock.
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chris Dunlop <chris@onthe.net.au>
Issue #4359
Issue #3508
Issue #4413
Issue #4827
We need to set inode->i_nlink to zero so iput will purge it. Without this, it
will get purged during shrink cache or umount, which would likely result in
deadlock due to zfs_zget waiting forever on its children which are in the
dispose_list of the same thread.
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chris Dunlop <chris@onthe.net.au>
Issue #4359
Issue #3508
Issue #4413
Issue #4827
When generation mismatch, it usually means the file pointed by the file handle
was deleted. We should return ESTALE to indicate this. We return ENOENT in
zfs_vget since zpl_fh_to_dentry will convert it to ESTALE.
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #4828
Allow accessing XATTR through export handle is a very bad idea. It
would allow user to write whatever they want in fields where they
otherwise could not.
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #4828
Certain ioctl operations will call get_zfs_sb, which will holds an active
count on sb without checking whether it's active or not. This will result
in use-after-free. We fix this by using atomic_inc_not_zero to make sure
we got an active sb.
P1 P2
--- ---
deactivate_locked_super(): s_active = 0
zfs_sb_hold()
->get_zfs_sb(): s_active = 1
->zpl_kill_sb()
-->zpl_put_super()
--->zfs_umount()
---->zfs_sb_free(zsb)
zfs_sb_rele(zsb)
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
If compiled with -O0, gcc doesn't do any stack frame coalescing
and -Wframe-larger-than=1024 is triggered in debug mode.
Starting with gcc 4.8, new opt level -Og is introduced for debugging, which
does not trigger this warning.
Fix bench zio size, using SPA_OLD_MAXBLOCKSHIFT
Signed-off-by: Gvozden Neskovic <neskovic@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4799
Reviewed by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Yuri Pankov <yuri.pankov@nexenta.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Calling dsl_dataset_name on a dataset with a 256 byte buffer is asking
for trouble. We should check every dataset on import, using a 1024 byte
buffer and checking each time to see if the dataset's new name is longer
than 256 bytes.
OpenZFS-issue: https://www.illumos.org/issues/6876
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/ca8674e
Adds ZFS_IOC_RECV_NEW for resumable streams and preserves the legacy
ZFS_IOC_RECV user/kernel interface. The new interface supports all
stream options but is currently only used for resumable streams.
This way updated user space utilities will interoperate with older
kernel modules.
ZFS_IOC_RECV_NEW is modeled after the existing ZFS_IOC_SEND_NEW
handler. Non-Linux OpenZFS platforms have opted to change the
legacy interface in an incompatible fashion instead of adding a
new ioctl.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Authored by: Dan McDonald <danmcd@omniti.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Yuri Pankov <yuri.pankov@nexenta.com>
Reviewed by: Toomas Soome <tsoome@me.com>
Approved by: Gordon Ross <gwr@nexenta.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/6562
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/5f7a8e6
Authored by: Dan McDonald <danmcd@omniti.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Approved by: Gordon Ross <gordon.ross@nexenta.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/4986
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/5878fad
2605 want to resume interrupted zfs send
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed by: Xin Li <delphij@freebsd.org>
Reviewed by: Arne Jansen <sensille@gmx.net>
Approved by: Dan McDonald <danmcd@omniti.com>
Ported-by: kernelOfTruth <kerneloftruth@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/2605
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/9c3fd12
6980 6902 causes zfs send to break due to 32-bit/64-bit struct mismatch
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Ported by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/6980
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/ea4a67f
Porting notes:
- All rsend and snapshop tests enabled and updated for Linux.
- Fix misuse of input argument in traverse_visitbp().
- Fix ISO C90 warnings and errors.
- Fix gcc 'missing braces around initializer' in
'struct send_thread_arg to_arg =' warning.
- Replace 4 argument fletcher_4_native() with 3 argument version,
this change was made in OpenZFS 4185 which has not been ported.
- Part of the sections for 'zfs receive' and 'zfs send' was
rewritten and reordered to approximate upstream.
- Fix mktree xattr creation, 'user.' prefix required.
- Minor fixes to newly enabled test cases
- Long holds for volumes allowed during receive for minor registration.
Justification
-------------
This feature adds support for variable length dnodes. Our motivation is
to eliminate the overhead associated with using spill blocks. Spill
blocks are used to store system attribute data (i.e. file metadata) that
does not fit in the dnode's bonus buffer. By allowing a larger bonus
buffer area the use of a spill block can be avoided. Spill blocks
potentially incur an additional read I/O for every dnode in a dnode
block. As a worst case example, reading 32 dnodes from a 16k dnode block
and all of the spill blocks could issue 33 separate reads. Now suppose
those dnodes have size 1024 and therefore don't need spill blocks. Then
the worst case number of blocks read is reduced to from 33 to two--one
per dnode block. In practice spill blocks may tend to be co-located on
disk with the dnode blocks so the reduction in I/O would not be this
drastic. In a badly fragmented pool, however, the improvement could be
significant.
ZFS-on-Linux systems that make heavy use of extended attributes would
benefit from this feature. In particular, ZFS-on-Linux supports the
xattr=sa dataset property which allows file extended attribute data
to be stored in the dnode bonus buffer as an alternative to the
traditional directory-based format. Workloads such as SELinux and the
Lustre distributed filesystem often store enough xattr data to force
spill bocks when xattr=sa is in effect. Large dnodes may therefore
provide a performance benefit to such systems.
Other use cases that may benefit from this feature include files with
large ACLs and symbolic links with long target names. Furthermore,
this feature may be desirable on other platforms in case future
applications or features are developed that could make use of a
larger bonus buffer area.
Implementation
--------------
The size of a dnode may be a multiple of 512 bytes up to the size of
a dnode block (currently 16384 bytes). A dn_extra_slots field was
added to the current on-disk dnode_phys_t structure to describe the
size of the physical dnode on disk. The 8 bits for this field were
taken from the zero filled dn_pad2 field. The field represents how
many "extra" dnode_phys_t slots a dnode consumes in its dnode block.
This convention results in a value of 0 for 512 byte dnodes which
preserves on-disk format compatibility with older software.
Similarly, the in-memory dnode_t structure has a new dn_num_slots field
to represent the total number of dnode_phys_t slots consumed on disk.
Thus dn->dn_num_slots is 1 greater than the corresponding
dnp->dn_extra_slots. This difference in convention was adopted
because, unlike on-disk structures, backward compatibility is not a
concern for in-memory objects, so we used a more natural way to
represent size for a dnode_t.
The default size for newly created dnodes is determined by the value of
a new "dnodesize" dataset property. By default the property is set to
"legacy" which is compatible with older software. Setting the property
to "auto" will allow the filesystem to choose the most suitable dnode
size. Currently this just sets the default dnode size to 1k, but future
code improvements could dynamically choose a size based on observed
workload patterns. Dnodes of varying sizes can coexist within the same
dataset and even within the same dnode block. For example, to enable
automatically-sized dnodes, run
# zfs set dnodesize=auto tank/fish
The user can also specify literal values for the dnodesize property.
These are currently limited to powers of two from 1k to 16k. The
power-of-2 limitation is only for simplicity of the user interface.
Internally the implementation can handle any multiple of 512 up to 16k,
and consumers of the DMU API can specify any legal dnode value.
The size of a new dnode is determined at object allocation time and
stored as a new field in the znode in-memory structure. New DMU
interfaces are added to allow the consumer to specify the dnode size
that a newly allocated object should use. Existing interfaces are
unchanged to avoid having to update every call site and to preserve
compatibility with external consumers such as Lustre. The new
interfaces names are given below. The versions of these functions that
don't take a dnodesize parameter now just call the _dnsize() versions
with a dnodesize of 0, which means use the legacy dnode size.
New DMU interfaces:
dmu_object_alloc_dnsize()
dmu_object_claim_dnsize()
dmu_object_reclaim_dnsize()
New ZAP interfaces:
zap_create_dnsize()
zap_create_norm_dnsize()
zap_create_flags_dnsize()
zap_create_claim_norm_dnsize()
zap_create_link_dnsize()
The constant DN_MAX_BONUSLEN is renamed to DN_OLD_MAX_BONUSLEN. The
spa_maxdnodesize() function should be used to determine the maximum
bonus length for a pool.
These are a few noteworthy changes to key functions:
* The prototype for dnode_hold_impl() now takes a "slots" parameter.
When the DNODE_MUST_BE_FREE flag is set, this parameter is used to
ensure the hole at the specified object offset is large enough to
hold the dnode being created. The slots parameter is also used
to ensure a dnode does not span multiple dnode blocks. In both of
these cases, if a failure occurs, ENOSPC is returned. Keep in mind,
these failure cases are only possible when using DNODE_MUST_BE_FREE.
If the DNODE_MUST_BE_ALLOCATED flag is set, "slots" must be 0.
dnode_hold_impl() will check if the requested dnode is already
consumed as an extra dnode slot by an large dnode, in which case
it returns ENOENT.
* The function dmu_object_alloc() advances to the next dnode block
if dnode_hold_impl() returns an error for a requested object.
This is because the beginning of the next dnode block is the only
location it can safely assume to either be a hole or a valid
starting point for a dnode.
* dnode_next_offset_level() and other functions that iterate
through dnode blocks may no longer use a simple array indexing
scheme. These now use the current dnode's dn_num_slots field to
advance to the next dnode in the block. This is to ensure we
properly skip the current dnode's bonus area and don't interpret it
as a valid dnode.
zdb
---
The zdb command was updated to display a dnode's size under the
"dnsize" column when the object is dumped.
For ZIL create log records, zdb will now display the slot count for
the object.
ztest
-----
Ztest chooses a random dnodesize for every newly created object. The
random distribution is more heavily weighted toward small dnodes to
better simulate real-world datasets.
Unused bonus buffer space is filled with non-zero values computed from
the object number, dataset id, offset, and generation number. This
helps ensure that the dnode traversal code properly skips the interior
regions of large dnodes, and that these interior regions are not
overwritten by data belonging to other dnodes. A new test visits each
object in a dataset. It verifies that the actual dnode size matches what
was stored in the ztest block tag when it was created. It also verifies
that the unused bonus buffer space is filled with the expected data
patterns.
ZFS Test Suite
--------------
Added six new large dnode-specific tests, and integrated the dnodesize
property into existing tests for zfs allow and send/recv.
Send/Receive
------------
ZFS send streams for datasets containing large dnodes cannot be received
on pools that don't support the large_dnode feature. A send stream with
large dnodes sets a DMU_BACKUP_FEATURE_LARGE_DNODE flag which will be
unrecognized by an incompatible receiving pool so that the zfs receive
will fail gracefully.
While not implemented here, it may be possible to generate a
backward-compatible send stream from a dataset containing large
dnodes. The implementation may be tricky, however, because the send
object record for a large dnode would need to be resized to a 512
byte dnode, possibly kicking in a spill block in the process. This
means we would need to construct a new SA layout and possibly
register it in the SA layout object. The SA layout is normally just
sent as an ordinary object record. But if we are constructing new
layouts while generating the send stream we'd have to build the SA
layout object dynamically and send it at the end of the stream.
For sending and receiving between pools that do support large dnodes,
the drr_object send record type is extended with a new field to store
the dnode slot count. This field was repurposed from unused padding
in the structure.
ZIL Replay
----------
The dnode slot count is stored in the uppermost 8 bits of the lr_foid
field. The bits were unused as the object id is currently capped at
48 bits.
Resizing Dnodes
---------------
It should be possible to resize a dnode when it is dirtied if the
current dnodesize dataset property differs from the dnode's size, but
this functionality is not currently implemented. Clearly a dnode can
only grow if there are sufficient contiguous unused slots in the
dnode block, but it should always be possible to shrink a dnode.
Growing dnodes may be useful to reduce fragmentation in a pool with
many spill blocks in use. Shrinking dnodes may be useful to allow
sending a dataset to a pool that doesn't support the large_dnode
feature.
Feature Reference Counting
--------------------------
The reference count for the large_dnode pool feature tracks the
number of datasets that have ever contained a dnode of size larger
than 512 bytes. The first time a large dnode is created in a dataset
the dataset is converted to an extensible dataset. This is a one-way
operation and the only way to decrement the feature count is to
destroy the dataset, even if the dataset no longer contains any large
dnodes. The complexity of reference counting on a per-dnode basis was
too high, so we chose to track it on a per-dataset basis similarly to
the large_block feature.
Signed-off-by: Ned Bass <bass6@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#3542
Only attempt to backfill lower metadnode object numbers if at least
4096 objects have been freed since the last rescan, and at most once
per transaction group. This avoids a pathology in dmu_object_alloc()
that caused O(N^2) behavior for create-heavy workloads and
substantially improves object creation rates. As summarized by
@mahrens in #4636:
"Normally, the object allocator simply checks to see if the next
object is available. The slow calls happened when dmu_object_alloc()
checks to see if it can backfill lower object numbers. This happens
every time we move on to a new L1 indirect block (i.e. every 32 *
128 = 4096 objects). When re-checking lower object numbers, we use
the on-disk fill count (blkptr_t:blk_fill) to quickly skip over
indirect blocks that don’t have enough free dnodes (defined as an L2
with at least 393,216 of 524,288 dnodes free). Therefore, we may
find that a block of dnodes has a low (or zero) fill count, and yet
we can’t allocate any of its dnodes, because they've been allocated
in memory but not yet written to disk. In this case we have to hold
each of the dnodes and then notice that it has been allocated in
memory.
The end result is that allocating N objects in the same TXG can
require CPU usage proportional to N^2."
Add a tunable dmu_rescan_dnode_threshold to define the number of
objects that must be freed before a rescan is performed. Don't bother
to export this as a module option because testing doesn't show a
compelling reason to change it. The vast majority of the performance
gain comes from limit the rescan to at most once per TXG.
Signed-off-by: Ned Bass <bass6@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Boris Protopopov <bprotopopov@hotmail.com>
Approved by: Richard Lowe <richlowe@richlowe.net>a
Ported by: Boris Protopopov <bprotopopov@actifio.com>
Signed-off-by: Boris Protopopov <bprotopopov@actifio.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/6513
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/8df0bcf0
If a ZFS object contains a hole at level one, and then a data block is
created at level 0 underneath that l1 block, l0 holes will be created.
However, these l0 holes do not have the birth time property set; as a
result, incremental sends will not send those holes.
Fix is to modify the dbuf_read code to fill in birth time data.
The commit f74b821 caused a regression where creating file through NFS will
always create a file owned by root. This is because the patch enables the KSID
code in zfs_acl_ids_create, which it would use euid and egid of the current
process. However, on Linux, we should use fsuid and fsgid for file operations,
which is the original behaviour. So we revert this part of code.
The patch also enables secpolicy_vnode_*, since they are also used in file
operations, we change them to use fsuid and fsgid.
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4772Closes#4758
This is a new implementation of RAIDZ1/2/3 routines using x86_64
scalar, SSE, and AVX2 instruction sets. Included are 3 parity
generation routines (P, PQ, and PQR) and 7 reconstruction routines,
for all RAIDZ level. On module load, a quick benchmark of supported
routines will select the fastest for each operation and they will
be used at runtime. Original implementation is still present and
can be selected via module parameter.
Patch contains:
- specialized gen/rec routines for all RAIDZ levels,
- new scalar raidz implementation (unrolled),
- two x86_64 SIMD implementations (SSE and AVX2 instructions sets),
- fastest routines selected on module load (benchmark).
- cmd/raidz_test - verify and benchmark all implementations
- added raidz_test to the ZFS Test Suite
New zfs module parameters:
- zfs_vdev_raidz_impl (str): selects the implementation to use. On
module load, the parameter will only accept first 3 options, and
the other implementations can be set once module is finished
loading. Possible values for this option are:
"fastest" - use the fastest math available
"original" - use the original raidz code
"scalar" - new scalar impl
"sse" - new SSE impl if available
"avx2" - new AVX2 impl if available
See contents of `/sys/module/zfs/parameters/zfs_vdev_raidz_impl` to
get the list of supported values. If an implementation is not supported
on the system, it will not be shown. Currently selected option is
enclosed in `[]`.
Signed-off-by: Gvozden Neskovic <neskovic@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4328
As of 4.6, the icache and dcache LRUs are memcg aware insofar as the
kernel's per-superblock shrinker is concerned. The effect is that dcache
or icache entries added by a task in a non-root memcg won't be scanned
by the shrinker in the context of the root (or NULL) memcg. This defeats
the attempts by zfs_sb_prune() to unpin buffers and can allow metadata to
grow uncontrollably. This patch reverts to the d_prune_aliaes() method
in case the kernel's per-superblock shrinker is not able to free anything.
Signed-off-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chunwei Chen <tuxoko@gmail.com>
Closes: #4726
ZFS allows for specific permissions to be delegated to normal users
with the `zfs allow` and `zfs unallow` commands. In addition, non-
privileged users should be able to run all of the following commands:
* zpool [list | iostat | status | get]
* zfs [list | get]
Historically this functionality was not available on Linux. In order
to add it the secpolicy_* functions needed to be implemented and mapped
to the equivalent Linux capability. Only then could the permissions on
the `/dev/zfs` be relaxed and the internal ZFS permission checks used.
Even with this change some limitations remain. Under Linux only the
root user is allowed to modify the namespace (unless it's a private
namespace). This means the mount, mountpoint, canmount, unmount,
and remount delegations cannot be supported with the existing code. It
may be possible to add this functionality in the future.
This functionality was validated with the cli_user and delegation test
cases from the ZFS Test Suite. These tests exhaustively verify each
of the supported permissions which can be delegated and ensures only
an authorized user can perform it.
Two minor bug fixes were required for test-running.py. First, the
Timer() object cannot be safely created in a `try:` block when there
is an unconditional `finally` block which references it. Second,
when running as a normal user also check for scripts using the
both the .ksh and .sh suffixes.
Finally, existing users who are simulating delegations by setting
group permissions on the /dev/zfs device should revert that
customization when updating to a version with this change.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#362Closes#434Closes#4100Closes#4394Closes#4410Closes#4487
Async writes triggered by a self-healing IO may be issued before the
pool finishes the process of initialization. This results in a NULL
dereference of `spa->spa_dsl_pool` in vdev_queue_max_async_writes().
George Wilson recommended addressing this issue by initializing the
passed `dsl_pool_t **` prior to dmu_objset_open_impl(). Since the
caller is passing the `spa->spa_dsl_pool` this has the effect of
ensuring it's initialized.
However, since this depends on the caller knowing they must pass
the `spa->spa_dsl_pool` an additional NULL check was added to
vdev_queue_max_async_writes(). This guards against any future
restructuring of the code which might result in dsl_pool_init()
being called differently.
Signed-off-by: GeLiXin <47034221@qq.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4652
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Approved by: Dan McDonald <danmcd@omniti.com>
Ported by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/6531
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/97e8130
Porting notes:
- Added new IO delay tracepoints, and moved common ZIO tracepoint macros
to a new trace_common.h file.
- Used zio_delay_taskq() in place of OpenZFS's timeout_generic() function.
- Updated zinject man page
- Updated zpool_scrub test files
arc_prune_task uses a refcount to protect arc_prune_t, but it doesn't prevent
the underlying zsb from disappearing if there's a concurrent umount. We fix
this by force the caller of arc_remove_prune_callback to wait for
arc_prune_taskq to finish.
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4687Closes#4690
Skip ctldir in zfs_rezget, otherwise they will always get invalidated. This
will cause funny behaviour for the mounted snapdirs. Especially for
Linux >= 3.18, d_invalidate will detach the mountpoint and prevent anyone
automount it again as long as someone is still using the detached mount.
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4514Closes#4661Closes#4672
Register iterate_shared if it exists so the kernel will used shared
lock and allowing concurrent readdir.
Also, use shared lock when doing llseek with SEEK_DATA or SEEK_HOLE
to allow concurrent seeking.
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4664Closes#4665
This field is a duplicate of the inode->i_generation, so just
kill it.
Signed-off-by: Nikolay Borisov <n.borisov.lkml@gmail.com>
Signed-off-by: Chunwei Chen <tuxoko@gmail.com>
Signed-off-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4538Closes#4654
This reverts commit 8302528617 and
ebecfcd699 which broke the build.
While these patches do apply cleanly and passed previous test
runs they need to be updated to account for the changes made in
commit 241b541574.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #3878
Fixed bug introduced in commit #c35b1882. Hinted by gcc:
zio_inject.c: In function ‘zio_handle_io_delay’:
zio_inject.c:382:3: warning: this ‘if’ clause does not guard... [-Wmisleading-indentation]
if (handler->zi_record.zi_freq != 0 &&
^~
zio_inject.c:384:4: note: ...this statement, but the latter is misleadingly indented as if it is guarded by the ‘if’
continue;
^~~~~~~~
Signed-off-by: Marcel Huber <marcelhuberfoo@gmail.com>
Signed-off-by: Chunwei Chen <tuxoko@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4632
struct zvol_state contains a dummy znode, which is around 1KB on x64,
only for zfs_range_lock. But in reality, other than z_range_lock and
z_range_avl, zfs_range_lock only need znode on regular file, which
means we add 1KB on a structure and gain nothing.
In this patch, we remove the dummy znode for zvol_state. In order to
do that, we also need to refactor zfs_range_lock a bit. We move
z_range_lock and z_range_avl pair out of znode_t to form zfs_rlock_t.
This new struct replaces znode_t as the main handle inside the range
lock functions.
We also add pointers to z_size, z_blksz, and z_max_blksz so range lock
code doesn't depend on znode_t. This allows non-ZPL consumers like
Lustre to use the range locks with their equivalent znode_t structure.
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Signed-off-by: Boris Protopopov <boris.protopopov@actifio.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4510
