If libselinux is detected on your system at configure time link
against it. This allows us to use a library call to detect if
selinux is enabled and if it is to pass the mount option:
"context=\"system_u:object_r:file_t:s0"
For now this is required because none of the existing selinux
policies are aware of the zfs filesystem type. Because of this
they do not properly enable xattr based labeling even though
zfs supports all of the required hooks.
Until distro's add zfs as a known xattr friendly fs type we
must use mntpoint labeling. Alternately, end users could modify
their existing selinux policy with a little guidance.
These compiler warnings were introduced when code which was
previously #ifdef'ed out by HAVE_ZPL was re-added for use
by the posix layer. All of the following changes should be
obviously correct and will cause no semantic changes.
Support for rolling back datasets require a functional ZPL, which we currently
do not have. The zfs command does not check for ZPL support before attempting
a rollback, and in preparation for rolling back a zvol it removes the minor
node of the device. To prevent the zvol device node from disappearing after a
failed rollback operation, this change wraps the zfs_do_rollback() function in
an #ifdef HAVE_ZPL and returns ENOSYS in the absence of a ZPL. This is
consistent with the behavior of other ZPL dependent commands such as mount.
The orginal error message observed with this bug was rather confusing:
internal error: Unknown error 524
Aborted
This was because zfs_ioc_rollback() returns ENOTSUP if we don't HAVE_ZPL, but
Linux actually has no such error code. It should instead return EOPNOTSUPP, as
that is how ENOTSUP is defined in user space. With that we would have gotten
the somewhat more helpful message
cannot rollback 'tank/fish': unsupported version
This is rather a moot point with the above changes since we will no longer make
that ioctl call without a ZPL. But, this change updates the error code just in
case.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
ZFS works best when it is notified as soon as possible when a device
failure occurs. This allows it to immediately start any recovery
actions which may be needed. In theory Linux supports a flag which
can be set on bio's called FAILFAST which provides this quick
notification by disabling the retry logic in the lower scsi layers.
That's the theory at least. In practice is turns out that while the
flag exists you oddly have to set it with the BIO_RW_AHEAD flag.
And even when it's set it you may get retries in the low level
drivers decides that's the right behavior, or if you don't get the
right error codes reported to the scsi midlayer.
Unfortunately, without additional kernels patchs there's not much
which can be done to improve this. Basically, this just means that
it may take 2-3 minutes before a ZFS is notified properly that a
device has failed. This can be improved and I suspect I'll be
submitting patches upstream to handle this.
One of the neat tricks an autoconf style project is capable of
is allow configurion/building in a directory other than the
source directory. The major advantage to this is that you can
build the project various different ways while making changes
in a single source tree.
For example, this project is designed to work on various different
Linux distributions each of which work slightly differently. This
means that changes need to verified on each of those supported
distributions perferably before the change is committed to the
public git repo.
Using nfs and custom build directories makes this much easier.
I now have a single source tree in nfs mounted on several different
systems each running a supported distribution. When I make a
change to the source base I suspect may break things I can
concurrently build from the same source on all the systems each
in their own subdirectory.
wget -c http://github.com/downloads/behlendorf/zfs/zfs-x.y.z.tar.gz
tar -xzf zfs-x.y.z.tar.gz
cd zfs-x-y-z
------------------------- run concurrently ----------------------
<ubuntu system> <fedora system> <debian system> <rhel6 system>
mkdir ubuntu mkdir fedora mkdir debian mkdir rhel6
cd ubuntu cd fedora cd debian cd rhel6
../configure ../configure ../configure ../configure
make make make make
make check make check make check make check
This change also moves many of the include headers from individual
incude/sys directories under the modules directory in to a single
top level include directory. This has the advantage of making
the build rules cleaner and logically it makes a bit more sense.
Add the initial products from autogen.sh. These products will
be updated incrementally after this point as development occurs.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
This topic branch contains required changes to the user space
utilities to allow them to integrate cleanly with Linux.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
This topic branch contains all the changes needed to integrate the user
side zfs tools with Linux style devices. Primarily this includes fixing
up the Solaris libefi library to be Linux friendly, and integrating with
the libblkid library which is provided by e2fsprogs.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Add autoconf style build infrastructure to the ZFS tree. This
includes autogen.sh, configure.ac, m4 macros, some scripts/*,
and makefiles for all the core ZFS components.
Fix non-c90 compliant code, for the most part these changes
simply deal with where a particular variable is declared.
Under c90 it must alway be done at the very start of a block.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
