It turns out that older versions of the glibc headers do not
properly define MS_DIRSYNC despite it being explicitly mentioned
in the man pages. They instead call it S_WRITE, so for system
where this is not correct defined map MS_DIRSYNC to S_WRITE.
At the time of this commit both Ubuntu Lucid, and Debian Squeeze
both use the out of date glibc headers.
As for MS_REC this field is also not available in the older headers.
Since there is no obvious mapping in this case we simply disable
the recursive mount option which used it.
ZFS even under Solaris does not strictly require libshare to be
available. The current implementation attempts to dlopen() the
library to access the needed symbols. If this fails libshare
support is simply disabled.
This means that on Linux we only need the most minimal libshare
implementation. In fact just enough to prevent the build from
failing. Longer term we can decide if we want to implement a
libshare library like Solaris. At best this would be an abstraction
layer between ZFS and NFS/SMB. Alternately, we can drop libshare
entirely and directly integrate ZFS with Linux's NFS/SMB.
Finally the bare bones user-libshare.m4 test was dropped. If we
do decide to implement libshare at some point it will surely be
as part of this package so the check is not needed.
By design the zfs utility is supposed to handle mounting and unmounting
a zfs filesystem. We could allow zfs to do this directly. There are
system calls available to mount/umount a filesystem. And there are
library calls available to manipulate /etc/mtab. But there are a
couple very good reasons not to take this appraoch... for now.
Instead of directly calling the system and library calls to (u)mount
the filesystem we fork and exec a (u)mount process. The principle
reason for this is to delegate the responsibility for locking and
updating /etc/mtab to (u)mount(8). This ensures maximum portability
and ensures the right locking scheme for your version of (u)mount
will be used. If we didn't do this we would have to resort to an
autoconf test to determine what locking mechanism is used.
The downside to using mount(8) instead of mount(2) is that we lose
the exact errno which was returned by the kernel. The return code
from mount(8) provides some insight in to what went wrong but it
not quite as good. For the moment this is translated as a best
guess in to a errno for the higher layers of zfs.
In the long term a shared library called libmount is under development
which provides a common API to address the locking and errno issues.
Once the standard mount utility has been updated to use this library
we can then leverage it. Until then this is the only safe solution.
http://www.kernel.org/pub/linux/utils/util-linux/libmount-docs/index.html
If libselinux is detected on your system at configure time link
against it. This allows us to use a library call to detect if
selinux is enabled and if it is to pass the mount option:
"context=\"system_u:object_r:file_t:s0"
For now this is required because none of the existing selinux
policies are aware of the zfs filesystem type. Because of this
they do not properly enable xattr based labeling even though
zfs supports all of the required hooks.
Until distro's add zfs as a known xattr friendly fs type we
must use mntpoint labeling. Alternately, end users could modify
their existing selinux policy with a little guidance.
Specifically, this fixes the two following errors in zdb when a pool
is composed of block devices:
1) 'Value too large for defined data type' when running 'zdb <dataset>'.
2) 'character device required' when running 'zdb -l <block-device>'.
Signed-off-by: Ricardo M. Correia <ricardo.correia@oracle.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
This commit fixes a sign extension bug affecting l2arc devices. Extremely
large offsets may be passed down to the low level block device driver on
reads, generating errors similar to
attempt to access beyond end of device
sdbi1: rw=14, want=36028797014862705, limit=125026959
The unwanted sign extension occurrs because the function arc_read_nolock()
stores the offset as a daddr_t, a 32-bit signed int type in the Linux kernel.
This offset is then passed to zio_read_phys() as a uint64_t argument, causing
sign extension for values of 0x80000000 or greater. To avoid this, we store
the offset in a uint64_t.
This change also changes a few daddr_t struct members to uint64_t in the libspl
headers to avoid similar bugs cropping up in the future. We also add an ASSERT
to __vdev_disk_physio() to check for invalid offsets.
Closes#66
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
ZFS works best when it is notified as soon as possible when a device
failure occurs. This allows it to immediately start any recovery
actions which may be needed. In theory Linux supports a flag which
can be set on bio's called FAILFAST which provides this quick
notification by disabling the retry logic in the lower scsi layers.
That's the theory at least. In practice is turns out that while the
flag exists you oddly have to set it with the BIO_RW_AHEAD flag.
And even when it's set it you may get retries in the low level
drivers decides that's the right behavior, or if you don't get the
right error codes reported to the scsi midlayer.
Unfortunately, without additional kernels patchs there's not much
which can be done to improve this. Basically, this just means that
it may take 2-3 minutes before a ZFS is notified properly that a
device has failed. This can be improved and I suspect I'll be
submitting patches upstream to handle this.
One of the neat tricks an autoconf style project is capable of
is allow configurion/building in a directory other than the
source directory. The major advantage to this is that you can
build the project various different ways while making changes
in a single source tree.
For example, this project is designed to work on various different
Linux distributions each of which work slightly differently. This
means that changes need to verified on each of those supported
distributions perferably before the change is committed to the
public git repo.
Using nfs and custom build directories makes this much easier.
I now have a single source tree in nfs mounted on several different
systems each running a supported distribution. When I make a
change to the source base I suspect may break things I can
concurrently build from the same source on all the systems each
in their own subdirectory.
wget -c http://github.com/downloads/behlendorf/zfs/zfs-x.y.z.tar.gz
tar -xzf zfs-x.y.z.tar.gz
cd zfs-x-y-z
------------------------- run concurrently ----------------------
<ubuntu system> <fedora system> <debian system> <rhel6 system>
mkdir ubuntu mkdir fedora mkdir debian mkdir rhel6
cd ubuntu cd fedora cd debian cd rhel6
../configure ../configure ../configure ../configure
make make make make
make check make check make check make check
This change also moves many of the include headers from individual
incude/sys directories under the modules directory in to a single
top level include directory. This has the advantage of making
the build rules cleaner and logically it makes a bit more sense.
All changes needed for the libspl layer. This includes modifications
to files directly copied from OpenSolaris and the addition of new
files needed to fill in the gaps.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
