The on-disk format for encrypted datasets protects not only
the encrypted and authenticated blocks themselves, but also
the order and interpretation of these blocks. In order to
make this work while maintaining the ability to do raw
sends, the indirect bps maintain a secure checksum of all
the MACs in the block below it along with a few other
fields that determine how the data is interpreted.
Unfortunately, the current on-disk format erroneously
includes some fields which are not portable and thus cannot
support raw sends. It is not possible to easily work around
this issue due to a separate and much smaller bug which
causes indirect blocks for encrypted dnodes to not be
compressed, which conflicts with the previous bug. In
addition, the current code generates incompatible on-disk
formats on big endian and little endian systems due to an
issue with how block pointers are authenticated. Finally,
raw send streams do not currently include dn_maxblkid when
sending both the metadnode and normal dnodes which are
needed in order to ensure that we are correctly maintaining
the portable objset MAC.
This patch zero's out the offending fields when computing
the bp MAC and ensures that these MACs are always
calculated in little endian order (regardless of the host
system's byte order). This patch also registers an errata
for the old on-disk format, which we detect by adding a
"version" field to newly created DSL Crypto Keys. We allow
datasets without a version (version 0) to only be mounted
for read so that they can easily be migrated. We also now
include dn_maxblkid in raw send streams to ensure the MAC
can be maintained correctly.
This patch also contains minor bug fixes and cleanups.
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#6845Closes#6864Closes#7052
* Remove 'zfs snap' from zfs help message (OpenZFS sync)
* Update zfs(8) to suggest 'snap' can be used as an alias for 'snapshot'
* Enforce 80 columns limit in help messages
* Remove zfs_disable_dup_eviction from zfs-module-parameters(5)
* Expose zfs_scan_max_ext_gap as a kernel module parameter.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#7087
Introduce kstats about the dbuf hash and dbuf cache
to make it easier to inspect state. This should help
with debugging and understanding of these portions
of the codebase.
Correct format of dbuf kstat file.
Introduce a dbc column to dbufs kstat to indicate if
a dbuf is in the dbuf cache.
Introduce field filtering in the dbufstat python script.
Introduce a no header option to the dbufstat python script.
Introduce a test case to test basic mru->mfu list movement
in the ARC.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#6906
The zdb(8) command may not terminate in the case where the pool
gets suspended and there is a caller in zio_wait() blocking on
an outstanding read I/O that will never complete. This can in
turn cause ztest(1) to block indefinitely despite the deadman.
Resolve the issue by setting the default failure mode for zdb(8)
to panic. In user space we always want the command to terminate
when forward progress is no longer possible.
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed by: Thomas Caputi <tcaputi@datto.com>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6999
The intent of this patch is extend the existing deadman code
such that it's flexible enough to be used by both ztest and
on production systems. The proposed changes include:
* Added a new `zfs_deadman_failmode` module option which is
used to dynamically control the behavior of the deadman. It's
loosely modeled after, but independant from, the pool failmode
property. It can be set to wait, continue, or panic.
* wait - Wait for the "hung" I/O (default)
* continue - Attempt to recover from a "hung" I/O
* panic - Panic the system
* Added a new `zfs_deadman_ziotime_ms` module option which is
analogous to `zfs_deadman_synctime_ms` except instead of
applying to a pool TXG sync it applies to zio_wait(). A
default value of 300s is used to define a "hung" zio.
* The ztest deadman thread has been re-enabled by default,
aligned with the upstream OpenZFS code, and then extended
to terminate the process when it takes significantly longer
to complete than expected.
* The -G option was added to ztest to print the internal debug
log when a fatal error is encountered. This same option was
previously added to zdb in commit fa603f82. Update zloop.sh
to unconditionally pass -G to obtain additional debugging.
* The FM_EREPORT_ZFS_DELAY event which was previously posted
when the deadman detect a "hung" pool has been replaced by
a new dedicated FM_EREPORT_ZFS_DEADMAN event.
* The proposed recovery logic attempts to restart a "hung"
zio by calling zio_interrupt() on any outstanding leaf zios.
We may want to further restrict this to zios in either the
ZIO_STAGE_VDEV_IO_START or ZIO_STAGE_VDEV_IO_DONE stages.
Calling zio_interrupt() is expected to only be useful for
cases when an IO has been submitted to the physical device
but for some reasonable the completion callback hasn't been
called by the lower layers. This shouldn't be possible but
has been observed and may be caused by kernel/driver bugs.
* The 'zfs_deadman_synctime_ms' default value was reduced from
1000s to 600s.
* Depending on how ztest fails there may be no cache file to
move. This should not be considered fatal, collect the logs
which are available and carry on.
* Add deadman test cases for spa_deadman() and zio_wait().
* Increase default zfs_deadman_checktime_ms to 60s.
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed by: Thomas Caputi <tcaputi@datto.com>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6999
usr/src/uts/common/sys/fs/zfs.h
Change ZPROP_INVAL and ZPROP_CONT from macros to enum values. Clang
and GCC both prefer to use unsigned ints to store enums. That was
causing tautological comparison warnings (and likely eliminating
error handling code at compile time) whenever a zfs_prop_t or
zpool_prop_t was compared to ZPROP_INVAL or ZPROP_CONT. Making the
error flags be explicity enum values forces the enum types to be
signed.
ZPROP_INVAL was also compared against two different enum types. I
had to change its name to ZPOOL_PROP_INVAL whenever its compared to
a zpool_prop_t. There are still some places where ZPROP_INVAL or
ZPROP_CONT is compared to a plain int, in code that doesn't know
whether the int is storing a zfs_prop_t or a zpool_prop_t.
usr/src/uts/common/fs/zfs/spa.c
s/ZPROP_INVAL/ZPOOL_PROP_INVAL/
Authored by: Alan Somers <asomers@gmail.com>
Approved by: Gordon Ross <gwr@nexenta.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Igor Kozhukhov <igor@dilos.org>
Reviewed by: George Melikov <mail@gmelikov.ru>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/8652
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/c2de80dc74Closes#7061
Resolve new warnings reported after upgrading to shellcheck
version 0.4.6. This patch contains no functional changes.
* egrep is non-standard and deprecated. Use grep -E instead. [SC2196]
* Check exit code directly with e.g. 'if mycmd;', not indirectly
with $?. [SC2181] Suppressed.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7040
For ztest, which is solely for testing, using a pseudo random
is entirely reasonable. Using /dev/urandom ensures the system
entropy pool doesn't get depleted thus stalling the testing.
This is a particular problem when testing in VMs.
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed by: Thomas Caputi <tcaputi@datto.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7017Closes#7036
When --enable-asan is provided to configure then build all user
space components with fsanitize=address. For kernel support
use the Linux KASAN feature instead.
https://github.com/google/sanitizers/wiki/AddressSanitizer
When using gcc version 4.8 any test case which intentionally
generates a core dump will fail when using --enable-asan.
The default behavior is to disable core dumps and only newer
versions allow this behavior to be controled at run time with
the ASAN_OPTIONS environment variable.
Additionally, this patch includes some build system cleanup.
* Rules.am updated to set the minimum AM_CFLAGS, AM_CPPFLAGS,
and AM_LDFLAGS. Any additional flags should be added on a
per-Makefile basic. The --enable-debug and --enable-asan
options apply to all user space binaries and libraries.
* Compiler checks consolidated in always-compiler-options.m4
and renamed for consistency.
* -fstack-check compiler flag was removed, this functionality
is provided by asan when configured with --enable-asan.
* Split DEBUG_CFLAGS in to DEBUG_CFLAGS, DEBUG_CPPFLAGS, and
DEBUG_LDFLAGS.
* Moved default kernel build flags in to module/Makefile.in and
split in to ZFS_MODULE_CFLAGS and ZFS_MODULE_CPPFLAGS. These
flags are set with the standard ccflags-y kbuild mechanism.
* -Wframe-larger-than checks applied only to binaries or
libraries which include source files which are built in
both user space and kernel space. This restriction is
relaxed for user space only utilities.
* -Wno-unused-but-set-variable applied only to libzfs and
libzpool. The remaining warnings are the result of an
ASSERT using a variable when is always declared.
* -D_POSIX_PTHREAD_SEMANTICS and -D__EXTENSIONS__ dropped
because they are Solaris specific and thus not needed.
* Ensure $GDB is defined as gdb by default in zloop.sh.
Signed-off-by: DHE <git@dehacked.net>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7027
Resolved unused variable warnings observed after restricting
-Wno-unused-but-set-variable to only libzfs and libzpool.
Reviewed-by: DHE <git@dehacked.net>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6941
In ztest_verify_dnode_bt the ztest_object_lock must be held in
order to safely verify the unused bonus space.
Reviewed-by: DHE <git@dehacked.net>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6941
This fixes zhack's command processing on ARM. On ARM char
is unsigned, and so, in promotion to an int, it will never
compare equal to -1.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Nathaniel Wesley Filardo <nwf@cs.jhu.edu>
Closes#7016
When replacing a faulted device which was previously handled by a spare
multiple levels of nested interior VDEVs will be present in the pool
configuration; the following example illustrates one of the possible
situations:
NAME STATE READ WRITE CKSUM
testpool DEGRADED 0 0 0
raidz1-0 DEGRADED 0 0 0
spare-0 DEGRADED 0 0 0
replacing-0 DEGRADED 0 0 0
/var/tmp/fault-dev UNAVAIL 0 0 0 cannot open
/var/tmp/replace-dev ONLINE 0 0 0
/var/tmp/spare-dev1 ONLINE 0 0 0
/var/tmp/safe-dev ONLINE 0 0 0
spares
/var/tmp/spare-dev1 INUSE currently in use
This is safe and allowed, but get_replication() needs to handle this
situation gracefully to let zpool add new devices to the pool.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#6678Closes#6996
This extends vdev_id to support a new slot type, ses, for SCSI Enclosure
Services. With slot type ses, the disk slot numbers are determined by
using the device slot number reported by sg_ses for the device with
matching SAS address, found by querying all available enclosures.
This is primarily of use on systems with a deficient driver omitting
support for bay_identifier in /sys/devices. In my testing, I found that
the existing slot types of port and id were not stable across disk
replacement, so an alternative was required.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Simon Guest <simon.guest@tesujimath.org>
Closes#6956
Using a command similar to 'arc_summary.py | head' causes
a broken pipe exception. Gracefully exit in the case of a
broken pipe in arc_summary.py.
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#6965Closes#6969
If an invalid option is provided to arc_summary.py we handle any error
thrown from the getopt Python module and print the usage help message.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#6983
The function that fills the uberblock ring buffer on every device label
has been reworked to avoid occasional failures caused by a race
condition that prevents 'zpool sync' from writing some uberblock
sequentially: this happens when the pool sync ioctl dispatch code calls
txg_wait_synced() while we're already waiting for a TXG to sync.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#6924Closes#6977
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#6962
* Teach ZED to handle spares usingi the configured ashift: if the zpool
'ashift' property is set then ZED should use its value when kicking
in a hotspare; with this change 512e disks can be used as spares
for VDEVs that were created with ashift=9, even if ZFS natively
detects them as 4K block devices.
* Introduce an additional auto_spare test case which verifies that in
the face of multiple device failures an appropiate number of spares
are kicked in.
* Fix zed_stop() in "libtest.shlib" which did not correctly wait the
target pid.
* Fix ZED crashing on startup caused by a race condition in libzfs
when used in multi-threaded context.
* Convert ZED over to using the tpool library which is already present
in the Illumos FMA code.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#2562Closes#6858
Fix a segfault when running 'zpool iostat -v 1' while adding
a VDEV.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#6748Closes#6872
Authored by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: Brad Lewis <brad.lewis@delphix.com>
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Dan McDonald <danmcd@joyent.com>
Ported-by: Prakash Surya <prakash.surya@delphix.com>
Problem
=======
The current implementation of zil_commit() can introduce significant
latency, beyond what is inherent due to the latency of the underlying
storage. The additional latency comes from two main problems:
1. When there's outstanding ZIL blocks being written (i.e. there's
already a "writer thread" in progress), then any new calls to
zil_commit() will block waiting for the currently oustanding ZIL
blocks to complete. The blocks written for each "writer thread" is
coined a "batch", and there can only ever be a single "batch" being
written at a time. When a batch is being written, any new ZIL
transactions will have to wait for the next batch to be written,
which won't occur until the current batch finishes.
As a result, the underlying storage may not be used as efficiently
as possible. While "new" threads enter zil_commit() and are blocked
waiting for the next batch, it's possible that the underlying
storage isn't fully utilized by the current batch of ZIL blocks. In
that case, it'd be better to allow these new threads to generate
(and issue) a new ZIL block, such that it could be serviced by the
underlying storage concurrently with the other ZIL blocks that are
being serviced.
2. Any call to zil_commit() must wait for all ZIL blocks in its "batch"
to complete, prior to zil_commit() returning. The size of any given
batch is proportional to the number of ZIL transaction in the queue
at the time that the batch starts processing the queue; which
doesn't occur until the previous batch completes. Thus, if there's a
lot of transactions in the queue, the batch could be composed of
many ZIL blocks, and each call to zil_commit() will have to wait for
all of these writes to complete (even if the thread calling
zil_commit() only cared about one of the transactions in the batch).
To further complicate the situation, these two issues result in the
following side effect:
3. If a given batch takes longer to complete than normal, this results
in larger batch sizes, which then take longer to complete and
further drive up the latency of zil_commit(). This can occur for a
number of reasons, including (but not limited to): transient changes
in the workload, and storage latency irregularites.
Solution
========
The solution attempted by this change has the following goals:
1. no on-disk changes; maintain current on-disk format.
2. modify the "batch size" to be equal to the "ZIL block size".
3. allow new batches to be generated and issued to disk, while there's
already batches being serviced by the disk.
4. allow zil_commit() to wait for as few ZIL blocks as possible.
5. use as few ZIL blocks as possible, for the same amount of ZIL
transactions, without introducing significant latency to any
individual ZIL transaction. i.e. use fewer, but larger, ZIL blocks.
In theory, with these goals met, the new allgorithm will allow the
following improvements:
1. new ZIL blocks can be generated and issued, while there's already
oustanding ZIL blocks being serviced by the storage.
2. the latency of zil_commit() should be proportional to the underlying
storage latency, rather than the incoming synchronous workload.
Porting Notes
=============
Due to the changes made in commit 119a394ab0, the lifetime of an itx
structure differs than in OpenZFS. Specifically, the itx structure is
kept around until the data associated with the itx is considered to be
safe on disk; this is so that the itx's callback can be called after the
data is committed to stable storage. Since OpenZFS doesn't have this itx
callback mechanism, it's able to destroy the itx structure immediately
after the itx is committed to an lwb (before the lwb is written to
disk).
To support this difference, and to ensure the itx's callbacks can still
be called after the itx's data is on disk, a few changes had to be made:
* A list of itxs was added to the lwb structure. This list contains
all of the itxs that have been committed to the lwb, such that the
callbacks for these itxs can be called from zil_lwb_flush_vdevs_done(),
after the data for the itxs is committed to disk.
* A list of itxs was added on the stack of the zil_process_commit_list()
function; the "nolwb_itxs" list. In some circumstances, an itx may
not be committed to an lwb (e.g. if allocating the "next" ZIL block
on disk fails), so this list is used to keep track of which itxs
fall into this state, such that their callbacks can be called after
the ZIL's writer pipeline is "stalled".
* The logic to actually call the itx's callback was moved into the
zil_itx_destroy() function. Since all consumers of zil_itx_destroy()
were effectively performing the same logic (i.e. if callback is
non-null, call the callback), it seemed like useful code cleanup to
consolidate this logic into a single function.
Additionally, the existing Linux tracepoint infrastructure dealing with
the ZIL's probes and structures had to be updated to reflect these code
changes. Specifically:
* The "zil__cw1" and "zil__cw2" probes were removed, so they had to be
removed from "trace_zil.h" as well.
* Some of the zilog structure's fields were removed, which affected
the tracepoint definitions of the structure.
* New tracepoints had to be added for the following 3 new probes:
* zil__process__commit__itx
* zil__process__normal__itx
* zil__commit__io__error
OpenZFS-issue: https://www.illumos.org/issues/8585
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/5d95a3aCloses#6566
When the pool configuration contains a hole due to a previous device
removal ignore this top level vdev. Failure to do so will result in
the current configuration being assessed to have a non-uniform
replication level and the expected warning will be disabled.
The zpool_add_010_pos test case was extended to cover this scenario.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6907Closes#6911
Display correct data from kstat arcstats for evict_skips,
which is currently repeating the data from mutex_misses.
Fixes#6882
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Scot W. Stevenson <scot.stevenson@gmail.com>
Closes#6882Closes#6883
Currently, scrubs and resilvers can take an extremely
long time to complete. This is largely due to the fact
that zfs scans process pools in logical order, as
determined by each block's bookmark. This makes sense
from a simplicity perspective, but blocks in zfs are
often scattered randomly across disks, particularly
due to zfs's copy-on-write mechanisms.
This patch improves performance by splitting scrubs
and resilvers into a metadata scanning phase and an IO
issuing phase. The metadata scan reads through the
structure of the pool and gathers an in-memory queue
of I/Os, sorted by size and offset on disk. The issuing
phase will then issue the scrub I/Os as sequentially as
possible, greatly improving performance.
This patch also updates and cleans up some of the scan
code which has not been updated in several years.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Authored-by: Saso Kiselkov <saso.kiselkov@nexenta.com>
Authored-by: Alek Pinchuk <apinchuk@datto.com>
Authored-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#3625Closes#6256
Remove unused library re and associated variable kstat_pobj. Add note
to documentation at start of program about required support for old
versions of Python. Change variable "format" (which is a built-in
function) to "fmt".
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Scot W. Stevenson <scot.stevenson@gmail.com>
Closes#6869
Prevents arc_summary.py crashing when called with parameter -d or
long form --description with Python3.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Scot W. Stevenson <scot.stevenson@gmail.com>
Closes#6849Closes#6850
Sort list of tunables printed by _tunable_summary()
alphabetically
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Scot W. Stevenson <scot.stevenson@gmail.com>
Closes#6828
Include docstrings (PEP8, PEP257) for module and all functions.
Separately, remove outdated section in comment at start of
module. Separately, remove unused global constant "usetunable".
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Scot W. Stevenson <scot.stevenson@gmail.com>
Closes#6818
Complete rewrite of fHits(). Move units from non-standard English
abbreviations to SI units, thereby avoiding confusion because of
"long scale" and "short scale" numbers. Remove unused parameter
"Decimal". Add function string. Aim to confirm to PEP8.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Scot W. Stevenson <scot.stevenson@gmail.com>
Closes#6815
Simplify and inline single-use function div1(); inline twice-used
function div2(); add function comment to zfs_header(); replace
variable "unused" in get_Kstat() with "_" following convention.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Scot W. Stevenson <scot.stevenson@gmail.com>
Closes#6802
Porting Notes:
- The OpenZFS patch added nicenum_scale() and nicenum() to a
library not used by ZFS. Rather than pull in a new dependency
the version of nicenum in lib/libzpool/util.c was simply
replaced with the new one.
Reviewed by: Sebastian Wiedenroth <wiedi@frubar.net>
Reviewed by: Robert Mustacchi <rm@joyent.com>
Reviewed by: Yuri Pankov <yuripv@gmx.com>
Approved by: Dan McDonald <danmcd@joyent.com>
Authored by: Jason King <jason.brian.king@gmail.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/640
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/0a055120Closes#6796
Replace if-elif-else construction with shorter loop;
remove unused parameter "Decimal"; centralize format
string; add function documentation string; conform to
PEP8.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Scot W. Stevenson <scot.stevenson@gmail.com>
Closes#6784
Fix compiler warnings in zdb. With these changes, FreeBSD can compile
zdb with all compiler warnings enabled save -Wunused-parameter.
usr/src/cmd/zdb/zdb.c
usr/src/cmd/zdb/zdb_il.c
usr/src/uts/common/fs/zfs/sys/sa.h
usr/src/uts/common/fs/zfs/sys/spa.h
Fix numerous warnings, including:
* const-correctness
* shadowing global definitions
* signed vs unsigned comparisons
* missing prototypes, or missing static declarations
* unused variables and functions
* Unreadable array initializations
* Missing struct initializers
usr/src/cmd/zdb/zdb.h
Add a header file to declare common symbols
usr/src/lib/libzpool/common/sys/zfs_context.h
usr/src/uts/common/fs/zfs/arc.c
usr/src/uts/common/fs/zfs/dbuf.c
usr/src/uts/common/fs/zfs/spa.c
usr/src/uts/common/fs/zfs/txg.c
Add a function prototype for zk_thread_create, and ensure that every
callback supplied to this function actually matches the prototype.
usr/src/cmd/ztest/ztest.c
usr/src/uts/common/fs/zfs/sys/zil.h
usr/src/uts/common/fs/zfs/zfs_replay.c
usr/src/uts/common/fs/zfs/zvol.c
Add a function prototype for zil_replay_func_t, and ensure that
every function of this type actually matches the prototype.
usr/src/uts/common/fs/zfs/sys/refcount.h
Change FTAG so it discards any constness of __func__, necessary
since existing APIs expect it passed as void *.
Porting Notes:
- Many of these fixes have already been applied to Linux. For
consistency the OpenZFS version of a change was applied if the
warning was addressed in an equivalent but different fashion.
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Prakash Surya <prakash.surya@delphix.com>
Authored by: Alan Somers <asomers@gmail.com>
Approved by: Richard Lowe <richlowe@richlowe.net>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/8081
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/843abe1b8aCloses#6787
Additionally add four new tests:
* zpool_events_clear: verify 'zpool events -c' functionality
* zpool_events_cliargs: verify command line options and arguments
* zpool_events_follow: verify 'zpool events -f'
* zpool_events_poolname: verify events filtering by pool name
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#3285Closes#6762
Added -n flag to zpool reopen that allows a running scrub
operation to continue if there is a device with Dirty Time Log.
By default if a component device has a DTL and zpool reopen
is executed all running scan operations will be restarted.
Added functional tests for `zpool reopen`
Tests covers following scenarios:
* `zpool reopen` without arguments,
* `zpool reopen` with pool name as argument,
* `zpool reopen` while scrubbing,
* `zpool reopen -n` while scrubbing,
* `zpool reopen -n` while resilvering,
* `zpool reopen` with bad arguments.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: Arkadiusz Bubała <arkadiusz.bubala@open-e.com>
Closes#6076Closes#6746
Otherwise, if arcstat gets interrupted before the desired number of
iterations is reached, the output file will be empty (both if set via
'-o' or via shell redirection).
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Fabian Grünbichler <f.gruenbichler@proxmox.com>
Closes#6775
Use mfu_size and mru_size pulled from the arcstats
kstat file to calculate the mfu and mru percentages
for arc size breakdown.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: AndCycle <andcycle@andcycle.idv.tw>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#5526Closes#6770
Fix new flake8 errors related to bare excepts and ambiguous
variable names due to a STYLE builder update.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#6776
Currently the 480GB models of this disk do not use ashift=12 by
default. SSDSC2BW48 is also optimized for 4k blocks.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: adisbladis <adis@blad.is>
Closes#6774
CID 161388: Resource Leak (REASOURCE_LEAK)
Jump to errout so that file descriptor gets closed before returning
from function.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Closes#6755
CID 147480: Logically dead code (DEADCODE)
Remove non-null check and subsequent function call. Add ASSERT to future
proof the code.
usage label is only jumped to before `zhp` is initialized.
CID 147584: Out-of-bounds access (OVERRUN)
Subtract length of current string from buffer length for `size` argument
to `snprintf`.
Starting address for the write is the start of the buffer + the current
string length. We need to subtract this string length else risk a buffer
overflow.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Closes#6745
Several issues were uncovered by running stress tests with zfs
encryption and raw sends in particular. The issues and their
associated fixes are as follows:
* arc_read_done() has the ability to chain several requests for
the same block of data via the arc_callback_t struct. In these
cases, the ARC would only use the first request's dsobj from
the bookmark to decrypt the data. This is problematic because
the first request might be a prefetch zio which is able to
handle the key not being loaded, while the second might use a
different key that it is sure will work. The fix here is to
pass the dsobj with each individual arc_callback_t so that each
request can attempt to decrypt the data separately.
* DRR_FREE and DRR_FREEOBJECT records in a send file were not
having their transactions properly tagged as raw during raw
sends, which caused a panic when the dbuf code attempted to
decrypt these blocks.
* traverse_prefetch_metadata() did not properly set
ZIO_FLAG_SPECULATIVE when issuing prefetch IOs.
* Added a few asserts and code cleanups to ensure these issues
are more detectable in the future.
Signed-off-by: Tom Caputi <tcaputi@datto.com>
* PBKDF2 implementation changed to OpenSSL implementation.
* HKDF implementation moved to its own file and tests
added to ensure correctness.
* Removed libzfs's now unnecessary dependency on libzpool
and libicp.
* Ztest can now create and test encrypted datasets. This is
currently disabled until issue #6526 is resolved, but
otherwise functions as advertised.
* Several small bug fixes discovered after enabling ztest
to run on encrypted datasets.
* Fixed coverity defects added by the encryption patch.
* Updated man pages for encrypted send / receive behavior.
* Fixed a bug where encrypted datasets could receive
DRR_WRITE_EMBEDDED records.
* Minor code cleanups / consolidation.
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Make two instances of the same change. Change bitwise AND (&) to logical
AND (&&).
Currently the code uses a bitwise AND between two boolean values.
In the first instance;
The first operand is a flag that has been bitwise combined with a bit
mask to get a boolean value as to whether a file has group write
permissions set.
The second operand used is a struct member that is intended as a
boolean flag not a bit mask.
In the second instance the argument is the same except with world write
permissions instead of group write (S_IWOTH, S_IWGRP).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Chris Dunlop <chris@onthe.net.au>
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Closes#6684Closes#6722
On systems with SCSI rather than SAS disk topology, this change enables
the vdev_id script to match against the block device path, and therefore
create a vdev alias in /dev/disk/by-vdev.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Simon Guest <simon.guest@tesujimath.org>
Closes#6592
Quote "$MMP_IMPORT_MSG" when it is passed as an argument, as it is a
multi-word string. Some tests were passing when they should not have,
because the grep was only testing for the first word.
Correct the message expected when no hostid is set and the test attempts
to enable multihost. It did not match the actual output in that
situation.
Disable ztest_reguid() when ztest is invoked with the -M option. If
ztest performs a reguid, a concurrent import attempt may fail with the
error "one or more devices is currently unavailable" if the guid sum is
calculated on the original device guids but compared against the guid
sum ztest wrote based on the new device guids.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#6666
FRU and LIBTOPO support are illumos only features that will not be ported to
Linux and make the code more complicated than necessary. This commit
makes way for further cleanups of the zed/FMA code.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: David Quigley <david.quigley@intel.com>
Closes#6641
The build for ztest always enabled debug information but does not enable
asserts unless --enable-debug is used. This will always enable asserts
in the ztest code.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: David Quigley <david.quigley@intel.com>
Closes#6640
This leverages the functionality introduced in cf7684b to expose
verbose, dry-run and parsable 'zfs send' options for bookmarks.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#3666Closes#6601
Refactor dmu_object_alloc_dnsize() and dnode_hold_impl() to simplify the
code, fix errors introduced by commit dbeb879 (PR #6117) interacting
badly with large dnodes, and improve performance.
* When allocating a new dnode in dmu_object_alloc_dnsize(), update the
percpu object ID for the core's metadnode chunk immediately. This
eliminates most lock contention when taking the hold and creating the
dnode.
* Correct detection of the chunk boundary to work properly with large
dnodes.
* Separate the dmu_hold_impl() code for the FREE case from the code for
the ALLOCATED case to make it easier to read.
* Fully populate the dnode handle array immediately after reading a
block of the metadnode from disk. Subsequently the dnode handle array
provides enough information to determine which dnode slots are in use
and which are free.
* Add several kstats to allow the behavior of the code to be examined.
* Verify dnode packing in large_dnode_008_pos.ksh. Since the test is
purely creates, it should leave very few holes in the metadnode.
* Add test large_dnode_009_pos.ksh, which performs concurrent creates
and deletes, to complement existing test which does only creates.
With the above fixes, there is very little contention in a test of about
200,000 racing dnode allocations produced by tests 'large_dnode_008_pos'
and 'large_dnode_009_pos'.
name type data
dnode_hold_dbuf_hold 4 0
dnode_hold_dbuf_read 4 0
dnode_hold_alloc_hits 4 3804690
dnode_hold_alloc_misses 4 216
dnode_hold_alloc_interior 4 3
dnode_hold_alloc_lock_retry 4 0
dnode_hold_alloc_lock_misses 4 0
dnode_hold_alloc_type_none 4 0
dnode_hold_free_hits 4 203105
dnode_hold_free_misses 4 4
dnode_hold_free_lock_misses 4 0
dnode_hold_free_lock_retry 4 0
dnode_hold_free_overflow 4 0
dnode_hold_free_refcount 4 57
dnode_hold_free_txg 4 0
dnode_allocate 4 203154
dnode_reallocate 4 0
dnode_buf_evict 4 23918
dnode_alloc_next_chunk 4 4887
dnode_alloc_race 4 0
dnode_alloc_next_block 4 18
The performance is slightly improved for concurrent creates with
16+ threads, and unchanged for low thread counts.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#5396Closes#6522Closes#6414Closes#6564
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#6535
Since OpenZFS 7578 (1b7c1e5) if we have a ZVOL with logbias=throughput
we will force WR_INDIRECT itxs in zvol_log_write() setting itx->itx_lr
offset and length to the offset and length of the BIO from
zvol_write()->zvol_log_write(): these offset and length are later used
to take a range lock in zillog->zl_get_data function: zvol_get_data().
Now suppose we have a ZVOL with blocksize=8K and push 4K writes to
offset 0: we will only be range-locking 0-4096. This means the
ASSERTion we make in dbuf_unoverride() is no longer valid because now
dmu_sync() is called from zilog's get_data functions holding a partial
lock on the dbuf.
Fix this by taking a range lock on the whole block in zvol_get_data().
Reviewed-by: Chunwei Chen <tuxoko@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#6238Closes#6315Closes#6356Closes#6477
* Removed zpios kmod, utility, headers and man page.
* Removed unused scripts zpios-profile/*, zpios-test/*,
zpool-config/*, smb.sh, zpios-sanity.sh, zpios-survey.sh,
zpios.sh, and zpool-create.sh.
* Removed zfs-script-config.sh.in. When building 'make' generates
a common.sh with in-tree path information from the common.sh.in
template. This file and sourced by the test scripts and used
for in-tree testing, it is not included in the packages. When
building packages 'make install' uses the same template to
create a new common.sh which is appropriate for the packaging.
* Removed unused functions/variables from scripts/common.sh.in.
Only minimal path information and configuration environment
variables remain.
* Removed unused scripts from scripts/ directory.
* Remaining shell scripts in the scripts directory updated to
cleanly pass shellcheck and added to checked scripts.
* Renamed tests/test-runner/cmd/ to tests/test-runner/bin/ to
match install location name.
* Removed last traces of the --enable-debug-dmu-tx configure
options which was retired some time ago.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6509
With HPE hardware and hpsa-driven SAS adapters, only a single phy is
reported, but no individual per-port phys (ie. no phy* entry below
port_dir), which breaks topology detection in the current sas_handler
code. Instead, slot information can be derived directly from the port
number. This change implements a new slot keyword "port" similar to
"id" and "lun", and assumes a default phy/port of 0 if no individual
phy entry can be found. It allows to use the "sas_direct" topology with
current HPE Dxxxx and Apollo 45xx JBODs.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Daniel Kobras <d.kobras@science-computing.de>
Closes#6484
Added a 'corrupt' error option that will flip a bit in the data
after a read operation. This is useful for generating checksum
errors at the device layer (in a mirror config for example). It
is also used to validate the diagnosis of checksum errors from
the zfs diagnosis engine.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@intel.com>
Closes#6345
This change incorporates three major pieces:
The first change is a keystore that manages wrapping
and encryption keys for encrypted datasets. These
commands mostly involve manipulating the new
DSL Crypto Key ZAP Objects that live in the MOS. Each
encrypted dataset has its own DSL Crypto Key that is
protected with a user's key. This level of indirection
allows users to change their keys without re-encrypting
their entire datasets. The change implements the new
subcommands "zfs load-key", "zfs unload-key" and
"zfs change-key" which allow the user to manage their
encryption keys and settings. In addition, several new
flags and properties have been added to allow dataset
creation and to make mounting and unmounting more
convenient.
The second piece of this patch provides the ability to
encrypt, decyrpt, and authenticate protected datasets.
Each object set maintains a Merkel tree of Message
Authentication Codes that protect the lower layers,
similarly to how checksums are maintained. This part
impacts the zio layer, which handles the actual
encryption and generation of MACs, as well as the ARC
and DMU, which need to be able to handle encrypted
buffers and protected data.
The last addition is the ability to do raw, encrypted
sends and receives. The idea here is to send raw
encrypted and compressed data and receive it exactly
as is on a backup system. This means that the dataset
on the receiving system is protected using the same
user key that is in use on the sending side. By doing
so, datasets can be efficiently backed up to an
untrusted system without fear of data being
compromised.
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#494Closes#5769
* Simplify threads, mutexs, cvs and rwlocks
* Update the zk_thread_create() function to use the same trick
as Illumos. Specifically, cast the new pthread_t to a void
pointer and return that as the kthread_t *. This avoids the
issues associated with managing a wrapper structure and is
safe as long as the callers never attempt to dereference it.
* Update all function prototypes passed to pthread_create() to
match the expected prototype. We were getting away this with
before since the function were explicitly cast.
* Replaced direct zk_thread_create() calls with thread_create()
for code consistency. All consumers of libzpool now use the
proper wrappers.
* The mutex_held() calls were converted to MUTEX_HELD().
* Removed all mutex_owner() calls and retired the interface.
Instead use MUTEX_HELD() which provides the same information
and allows the implementation details to be hidden. In this
case the use of the pthread_equals() function.
* The kthread_t, kmutex_t, krwlock_t, and krwlock_t types had
any non essential fields removed. In the case of kthread_t
and kcondvar_t they could be directly typedef'd to pthread_t
and pthread_cond_t respectively.
* Removed all extra ASSERTS from the thread, mutex, rwlock, and
cv wrapper functions. In practice, pthreads already provides
the vast majority of checks as long as we check the return
code. Removing this code from our wrappers help readability.
* Added TS_JOINABLE state flag to pass to request a joinable rather
than detached thread. This isn't a standard thread_create() state
but it's the least invasive way to pass this information and is
only used by ztest.
TEST_ZTEST_TIMEOUT=3600
Chunwei Chen <tuxoko@gmail.com>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4547Closes#5503Closes#5523Closes#6377Closes#6495
OpenZFS provides a library called tpool which implements thread
pools for user space applications. Porting this library means
the zpool utility no longer needs to borrow the kernel mutex and
taskq interfaces from libzpool. This code was updated to use
the tpool library which behaves in a very similar fashion.
Porting libtpool was relatively straight forward and minimal
modifications were needed. The core changes were:
* Fully convert the library to use pthreads.
* Updated signal handling.
* lmalloc/lfree converted to calloc/free
* Implemented portable pthread_attr_clone() function.
Finally, update the build system such that libzpool.so is no
longer linked in to zfs(8), zpool(8), etc. All that is required
is libzfs to which the zcommon soures were added (which is the way
it always should have been). Removing the libzpool dependency
resulted in several build issues which needed to be resolved.
* Moved zfeature support to module/zcommon/zfeature_common.c
* Moved ratelimiting to to module/zfs/zfs_ratelimit.c
* Moved get_system_hostid() to lib/libspl/gethostid.c
* Removed use of cmn_err() in zcommon source
* Removed dprintf_setup() call from zpool_main.c and zfs_main.c
* Removed highbit() and lowbit()
* Removed unnecessary library dependencies from Makefiles
* Removed fletcher-4 kstat in user space
* Added sha2 support explicitly to libzfs
* Added highbit64() and lowbit64() to zpool_util.c
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6442
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Sen Haerens <sen@senhaerens.be>
Closes#6444Closes#6445
Check in the DMU whether an object record in a send stream being
received contains an unsupported dnode slot count, and return an
error if it does. Failure to catch an unsupported dnode slot count
would result in a panic when the SPA attempts to increment the
reference count for the large_dnode feature and the pool has the
feature disabled. This is not normally an issue for a well-formed
send stream which would have the DMU_BACKUP_FEATURE_LARGE_DNODE flag
set if it contains large dnodes, so it will be rejected as
unsupported if the required feature is disabled. This change adds a
missing object record field validation.
Add missing stream feature flag checks in
dmu_recv_resume_begin_check().
Consolidate repetitive comment blocks in dmu_recv_begin_check().
Update zstreamdump to print the dnode slot count (dn_slots) for an
object record when running in verbose mode.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Ned Bass <bass6@llnl.gov>
Closes#6396
Add a callback to wake all running mmp threads when
zfs_multihost_interval is changed.
This is necessary when the interval is changed from a very large value
to a significantly lower one, while pools are imported that have the
multihost property enabled.
Without this commit, the mmp thread does not wake up and detect the new
interval until after it has waited the old multihost interval time. A
user monitoring mmp writes via the provided kstat would be led to
believe that the changed setting did not work.
Added a test in the ZTS under mmp to verify the new functionality is
working.
Added a test to ztest which starts and stops mmp threads, and calls into
the code to signal sleeping mmp threads, to test for deadlocks or
similar locking issues.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#6387
"zhack feature stat" performs a read-only import, so the MMP activity
check is not necessary.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#6388Closes#6389
Turning the multihost property on requires that a hostid be set to allow
ZFS to determine when a foreign system is attemping to import a pool.
The error message instructing the user to set a hostid refers to
genhostid(1).
Genhostid(1) is not available on SUSE Linux. This commit adds a script
modeled after genhostid(1) for those users.
Zgenhostid checks for an /etc/hostid file; if it does not exist, it
creates one and stores a value. If the user has provided a hostid as an
argument, that value is used. Otherwise, a random hostid is generated
and stored.
This differs from the CENTOS 6/7 versions of genhostid, which overwrite
the /etc/hostid file even though their manpages state otherwise.
A man page for zgenhostid is added. The one for genhostid is in (1), but
I put zgenhostid in (8) because I believe it's more appropriate.
The mmp tests are modified to use zgenhostid to set the hostid instead
of using the spl_hostid module parameter. zgenhostid will not replace
an existing /etc/hostid file, so new mmp_clear_hostid calls are
required.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#6358Closes#6379
When replacing a disk with non-wholedisk spare, we shouldn't zero_label
it. The wholedisk case already skip it. In fact, zero_label function
will fail saying device busy because it's already opened exclusively,
but since there's no error checking, the replace command will succeed,
causing great confusion.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Closes#6369
zpool iostat/status -c is supposed to be restricted
by its search path, but currently isn't. To prevent
arbitrary scripts from being executed, disallow '/'
from commands.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Ned Bass <bass6@llnl.gov>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#6353Closes#6359
CID 165757: Control flow issues (MISSING_BREAK)
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: George Melikov <mail@gmelikov.ru>
Closes#6348
Add multihost=on|off pool property to control MMP. When enabled
a new thread writes uberblocks to the last slot in each label, at a
set frequency, to indicate to other hosts the pool is actively imported.
These uberblocks are the last synced uberblock with an updated
timestamp. Property defaults to off.
During tryimport, find the "best" uberblock (newest txg and timestamp)
repeatedly, checking for change in the found uberblock. Include the
results of the activity test in the config returned by tryimport.
These results are reported to user in "zpool import".
Allow the user to control the period between MMP writes, and the
duration of the activity test on import, via a new module parameter
zfs_multihost_interval. The period is specified in milliseconds. The
activity test duration is calculated from this value, and from the
mmp_delay in the "best" uberblock found initially.
Add a kstat interface to export statistics about Multiple Modifier
Protection (MMP) updates. Include the last synced txg number, the
timestamp, the delay since the last MMP update, the VDEV GUID, the VDEV
label that received the last MMP update, and the VDEV path. Abbreviated
output below.
$ cat /proc/spl/kstat/zfs/mypool/multihost
31 0 0x01 10 880 105092382393521 105144180101111
txg timestamp mmp_delay vdev_guid vdev_label vdev_path
20468 261337 250274925 68396651780 3 /dev/sda
20468 261339 252023374 6267402363293 1 /dev/sdc
20468 261340 252000858 6698080955233 1 /dev/sdx
20468 261341 251980635 783892869810 2 /dev/sdy
20468 261342 253385953 8923255792467 3 /dev/sdd
20468 261344 253336622 042125143176 0 /dev/sdab
20468 261345 253310522 1200778101278 2 /dev/sde
20468 261346 253286429 0950576198362 2 /dev/sdt
20468 261347 253261545 96209817917 3 /dev/sds
20468 261349 253238188 8555725937673 3 /dev/sdb
Add a new tunable zfs_multihost_history to specify the number of MMP
updates to store history for. By default it is set to zero meaning that
no MMP statistics are stored.
When using ztest to generate activity, for automated tests of the MMP
function, some test functions interfere with the test. For example, the
pool is exported to run zdb and then imported again. Add a new ztest
function, "-M", to alter ztest behavior to prevent this.
Add new tests to verify the new functionality. Tests provided by
Giuseppe Di Natale.
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Ned Bass <bass6@llnl.gov>
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#745Closes#6279
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Alex Reece <alex@delphix.com>
Reviewed by: Yuri Pankov <yuri.pankov@gmail.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/8067
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/8173085Closes#6319
Currently, there is no way to pause a scrub. Pausing may
be useful when the pool is busy with other I/O to preserve
bandwidth.
This patch adds the ability to pause and resume scrubbing.
This is achieved by maintaining a persistent on-disk scrub state.
While the state is 'paused' we do not scrub any more blocks.
We do however perform regular scan housekeeping such as
freeing async destroyed and deadlist blocks while paused.
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Thomas Caputi <tcaputi@datto.com>
Reviewed-by: Serapheim Dimitropoulos <serapheimd@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alek Pinchuk <apinchuk@datto.com>
Closes#6167
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
The problem is that zfs_get_data() supplies a stale zgd_bp to
dmu_sync(), which we then nopwrite against.
zfs_get_data() doesn't hold any DMU-related locks, so after it
copies db_blkptr to zgd_bp, dbuf_write_ready() could change
db_blkptr, and dbuf_write_done() could remove the dirty record.
dmu_sync() then sees the stale BP and that the dbuf it not dirty,
so it is eligible for nop-writing.
The fix is for dmu_sync() to copy db_blkptr to zgd_bp after
acquiring the db_mtx. We could still see a stale db_blkptr,
but if it is stale then the dirty record will still exist and
thus we won't attempt to nopwrite.
OpenZFS-issue: https://www.illumos.org/issues/8378
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/3127742Closes#6293
Resolves issues discovered when porting to OpenZFS.
* Lint warnings.
* Made dnode_move_impl() large dnode aware. This
functionality is currently unused on Linux.
Reviewed-by: Ned Bass <bass6@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#6262
GCC 7.1 with will warn when we're not checking the snprintf()
return code in cases where the buffer could be truncated. This
patch either checks the snprintf return code (where applicable),
or simply disables the warnings (ztest.c).
Reviewed-by: Chunwei Chen <david.chen@osnexus.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#6253
This prints dashes instead of zeros for zero latency values in
'zpool iostat -p'. You'll get zero latencies reported when the
disk is idle, but technically a zero latency is invalid, since you
can't measure the latency of doing nothing.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#6210
In the original form of device error injection, it was an all or nothing
situation. To help simulate intermittent error conditions, you can now
specify a real number percentage value. This is also very useful for our
ZFS fault diagnosis testing and for injecting intermittent errors during
load testing.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@intel.com>
Closes#6227
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: DHE <git@dehacked.net>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Jack Draak <jackdraak@gmail.com>
Signed-off-by: Kash Pande <kash@tripleback.net>
Closes#6203
- After some ZIL changes 6 years ago zil_slog_limit got partially broken
due to zl_itx_list_sz not updated when async itx'es upgraded to sync.
Actually because of other changes about that time zl_itx_list_sz is not
really required to implement the functionality, so this patch removes
some unneeded broken code and variables.
- Original idea of zil_slog_limit was to reduce chance of SLOG abuse by
single heavy logger, that increased latency for other (more latency critical)
loggers, by pushing heavy log out into the main pool instead of SLOG. Beside
huge latency increase for heavy writers, this implementation caused double
write of all data, since the log records were explicitly prepared for SLOG.
Since we now have I/O scheduler, I've found it can be much more efficient
to reduce priority of heavy logger SLOG writes from ZIO_PRIORITY_SYNC_WRITE
to ZIO_PRIORITY_ASYNC_WRITE, while still leave them on SLOG.
- Existing ZIL implementation had problem with space efficiency when it
has to write large chunks of data into log blocks of limited size. In some
cases efficiency stopped to almost as low as 50%. In case of ZIL stored on
spinning rust, that also reduced log write speed in half, since head had to
uselessly fly over allocated but not written areas. This change improves
the situation by offloading problematic operations from z*_log_write() to
zil_lwb_commit(), which knows real situation of log blocks allocation and
can split large requests into pieces much more efficiently. Also as side
effect it removes one of two data copy operations done by ZIL code WR_COPIED
case.
- While there, untangle and unify code of z*_log_write() functions.
Also zfs_log_write() alike to zvol_log_write() can now handle writes crossing
block boundary, that may also improve efficiency if ZPL is made to do that.
Sponsored by: iXsystems, Inc.
Authored by: Alexander Motin <mav@FreeBSD.org>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: Andriy Gapon <avg@FreeBSD.org>
Reviewed by: Steven Hartland <steven.hartland@multiplay.co.uk>
Reviewed by: Brad Lewis <brad.lewis@delphix.com>
Reviewed by: Richard Elling <Richard.Elling@RichardElling.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <ryao@gentoo.org>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/7578
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/aeb13acCloses#6191
Commit torvalds/linux@9e8925b6 allowed for kernels to be built
without support for mandatory locking (MS_MANDLOCK). This will
result in 'zfs mount' failing when the nbmand=on property is set
if the kernel is built without CONFIG_MANDATORY_FILE_LOCKING.
Unfortunately we can not reliably detect prior to the mount(2) system
call if the kernel was built with this support. The best we can do
is check if the mount failed with EPERM and if we passed 'mand'
as a mount option and then print a more useful error message. e.g.
filesystem 'tank/fs' has the 'nbmand=on' property set, this mount
option may be disabled in your kernel. Use 'zfs set nbmand=off'
to disable this option and try to mount the filesystem again.
Additionally, switch the default error message case to use
strerror() to produce a more human readable message.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4729Closes#6199
Allow new members to be added to a pool mixing raidz and mirror vdevs
without giving -f, as long as they have matching redundancy. This case
was missed in #5915, which only handled zpool create.
Add zfstest zpool_add_010_pos.ksh, with test of zpool create
followed by zpool add of mixed raidz and mirror vdevs.
Add some more mixed raidz and mirror cases to zpool_create_006_pos.ksh.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Haakan Johansson <f96hajo@chalmers.se>
Issue #5915Closes#6181
Users can now provide their own scripts to be run
with 'zpool iostat/status -c'. User scripts should be
placed in ~/.zpool.d to be included in zpool's
default search path.
Provide a script which can be used with
'zpool iostat|status -c' that will return the type of
device (hdd, sdd, file).
Provide a script to get various values from smartctl
when using 'zpool iostat/status -c'.
Allow users to define the ZPOOL_SCRIPTS_PATH
environment variable which can be used to override
the default 'zpool iostat/status -c' search path.
Allow the ZPOOL_SCRIPTS_ENABLED environment
variable to enable or disable 'zpool status/iostat -c'
functionality.
Use the new smart script to provide the serial command.
Install /etc/sudoers.d/zfs file which contains the sudoer
rule for smartctl as a sample.
Allow 'zpool iostat/status -c' tests to run in tree.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#6121Closes#6153
Enable most of the remaining test cases which were previously
disabled. The required fixes are as follows:
* cache_001_pos - No changes required.
* cache_010_neg - Updated to use losetup under Linux. Loopback
cache devices are allowed, ZVOLs as cache devices are not.
Disabled until all the builders pass reliably.
* cachefile_001_pos, cachefile_002_pos, cachefile_003_pos,
cachefile_004_pos - Set set_device_dir path in cachefile.cfg,
updated CPATH1 and CPATH2 to reference unique files.
* zfs_clone_005_pos - Wait for udev to create volumes.
* zfs_mount_007_pos - Updated mount options to expected Linux names.
* zfs_mount_009_neg, zfs_mount_all_001_pos - No changes required.
* zfs_unmount_005_pos, zfs_unmount_009_pos, zfs_unmount_all_001_pos -
Updated to expect -f to not unmount busy mount points under Linux.
* rsend_019_pos - Observed to occasionally take a long time on both
32-bit systems and the kmemleak builder.
* zfs_written_property_001_pos - Switched sync(1) to sync_pool.
* devices_001_pos, devices_002_neg - Updated create_dev_file() helper
for Linux.
* exec_002_neg.ksh - Fixed mmap_exec.c to preserve errno. Updated
test case to expect EPERM from Linux as described by mmap(2).
* grow_pool_001_pos - Adding missing setup.ksh and cleanup.ksh
scripts from OpenZFS.
* grow_replicas_001_pos.ksh - Added missing $SLICE_* variables.
* history_004_pos, history_006_neg, history_008_pos - Fixed by
previous commits and were not enabled. No changes required.
* zfs_allow_010_pos - Added missing spaces after assorted zfs
commands in delegate_common.kshlib.
* inuse_* - Illumos dump device tests skipped. Remaining test
cases updated to correctly create required partitions.
* large_files_001_pos - Fixed largest_file.c to accept EINVAL
as well as EFBIG as described in write(2).
* link_count_001 - Added nproc to required commands.
* umountall_001 - Updated to use umount -a.
* online_offline_001_* - Pull in OpenZFS change to file_trunc.c
to make the '-c 0' option run the test in a loop. Included
online_offline.cfg file in all test cases.
* rename_dirs_001_pos - Updated to use the rename_dir test binary,
pkill restricted to exact matches and total runtime reduced.
* slog_013_neg, write_dirs_002_pos - No changes required.
* slog_013_pos.ksh - Updated to use losetup under Linux.
* slog_014_pos.ksh - ZED will not be running, manually degrade
the damaged vdev as expected.
* nopwrite_varying_compression, nopwrite_volume - Forced pool
sync with sync_pool to ensure up to date property values.
* Fixed typos in ZED log messages. Refactored zed_* helper
functions to resolve all-syslog exit=1 errors in zedlog.
* zfs_copies_005_neg, zfs_get_004_pos, zpool_add_004_pos,
zpool_destroy_001_pos, largest_pool_001_pos, clone_001_pos.ksh,
clone_001_pos, - Skip until layering pools on zvols is solid.
* largest_pool_001_pos - Limited to 7eb pool, maximum
supported size in 8eb-1 on Linux.
* zpool_expand_001_pos, zpool_expand_003_neg - Requires
additional support from the ZED, updated skip reason.
* zfs_rollback_001_pos, zfs_rollback_002_pos - Properly cleanup
busy mount points under Linux between test loops.
* privilege_001_pos, privilege_003_pos, rollback_003_pos,
threadsappend_001_pos - Skip with log_unsupported.
* snapshot_016_pos - No changes required.
* snapshot_008_pos - Increased LIMIT from 512K to 2M and added
sync_pool to avoid false positives.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6128
This addition will enable us to sync an open TXG to the main pool
on demand. The functionality is similar to 'sync(2)' but 'zpool sync'
will return when data has hit the main storage instead of potentially
just the ZIL as is the case with the 'sync(2)' cmd.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Alek Pinchuk <apinchuk@datto.com>
Closes#6122
This patch adds a '-f' option to 'zpool offline' to fault a vdev
instead of bringing it offline. Unlike the OFFLINE state, the
FAULTED state will trigger the FMA code, allowing for things like
autoreplace and triggering the slot fault LED. The -f faults
persist across imports, unless they were set with the temporary
(-t) flag. Both persistent and temporary faults can be cleared
with zpool clear.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#6094
Enable additional test cases, in most cases this required a few
minor modifications to the test scripts. In a few cases a real
bug was uncovered and fixed. And in a handful of cases where pools
are layered on pools the test case will be skipped until this is
supported. Details below for each test case.
* zpool_add_004_pos - Skip test on Linux until adding zvols to pools
is fully supported and deadlock free.
* zpool_add_005_pos.ksh - Skip dumpadm portion of the test which isn't
relevant for Linux. The find_vfstab_dev, find_mnttab_dev, and
save_dump_dev functions were updated accordingly for Linux. Add
O_EXCL to the in-use check to prevent the -f (force) option from
working for mounted filesystems and improve the resulting error.
* zpool_add_006_pos - Update test case such that it doesn't depend
on nested pools. Switch to truncate from mkfile to reduce space
requirements and speed up the test case.
* zpool_clear_001_pos - Speed up test case by filling filesystem to
25% capacity.
* zpool_create_002_pos, zpool_create_004_pos - Use sparse files for
file vdevs in order to avoid increasing the partition size.
* zpool_create_006_pos - 6ba1ce9 allows raidz+mirror configs with
similar redundancy. Updating the valid_args and forced_args cases.
* zpool_create_008_pos - Disable overlapping partition portion.
* zpool_create_011_neg - Fix to correctly create the extra partition.
Modified zpool_vdev.c to use fstat64_blk() wrapper which includes
the st_size even for block devices.
* zpool_create_012_neg - Updated to properly find swap devices.
* zpool_create_014_neg, zpool_create_015_neg - Updated to use
swap_setup() and swap_cleanup() wrappers which do the right thing
on Linux and Illumos. Removed '-n' option which succeeds under
Linux due to differences in the in-use checks.
* zpool_create_016_pos.ksh - Skipped test case isn't useful.
* zpool_create_020_pos - Added missing / to cleanup() function.
Remove cache file prior to test to ensure a clean environment
and avoid false positives.
* zpool_destroy_001_pos - Removed test case which creates a pool on
a zvol. This is more likely to deadlock under Linux and has never
been completely supported on any platform.
* zpool_destroy_002_pos - 'zpool destroy -f' is unsupported on Linux.
Mount point must not be busy in order to unmount them.
* zfs_destroy_001_pos - Handle EBUSY error which can occur with
volumes when racing with udev.
* zpool_expand_001_pos, zpool_expand_003_neg - Skip test on Linux
until adding zvols to pools is fully supported and deadlock free.
The test could be modified to use loop-back devices but it would
be preferable to use the test case as is for improved coverage.
* zpool_export_004_pos - Updated test case to such that it doesn't
depend on nested pools. Normal file vdev under /var/tmp are fine.
* zpool_import_all_001_pos - Updated to skip partition 1, which is
known as slice 2, on Illumos. This prevents overwriting the
default TESTPOOL which was causing the failure.
* zpool_import_002_pos, zpool_import_012_pos - No changes needed.
* zpool_remove_003_pos - No changes needed
* zpool_upgrade_002_pos, zpool_upgrade_004_pos - Root cause addressed
by upstream OpenZFS commit 3b7f360.
* zpool_upgrade_007_pos - Disabled in test case due to known failure.
Opened issue https://github.com/zfsonlinux/zfs/issues/6112
* zvol_misc_002_pos - Updated to to use ext2.
* zvol_misc_001_neg, zvol_misc_003_neg, zvol_misc_004_pos,
zvol_misc_005_neg, zvol_misc_006_pos - Moved to skip list, these
test case could be updated to use Linux's crash dump facility.
* zvol_swap_* - Updated to use swap_setup/swap_cleanup helpers.
File creation switched from /tmp to /var/tmp. Enabled minimal
useful tests for Linux, skip test cases which aren't applicable.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #3484
Issue #5634
Issue #2437
Issue #5202
Issue #4034Closes#6095
This allows users to specify "-o property=value" to override and
"-x property" to exclude properties when receiving a zfs send stream.
Both native and user properties can be specified.
This is useful when using zfs send/receive for periodic
backup/replication because it lets users change properties such as
canmount, mountpoint, or compression without modifying the source.
References:
https://www.illumos.org/issues/2745https://www.illumos.org/issues/3753
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Alek Pinchuk <apinchuk@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#1350Closes#5349
CID 161638: Resource leak (RESOURCE_LEAK)
Ensure the string array in print_zpool_script_help
is freed in cases when there is an error.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#6111
The proposed debugging enhancements in zfsonlinux/spl#587
identified the following missing *_destroy/*_fini calls.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Gvozden Neskovic <neskovic@gmail.com>
Closes#5428
This commit allow higher ashift values (up to 16) in 'zpool create'
The ashift value was previously limited to 13 (8K block) in b41c990
because the limited number of uberblocks we could fit in the
statically sized (128K) vdev label ring buffer could prevent the
ability the safely roll back a pool to recover it.
Since b02fe35 the largest uberblock size we support is 8K: this
allow us to store a minimum number of 16 uberblocks in the vdev
label, even with higher ashift values.
Additionally change 'ashift' pool property behaviour: if set it will
be used as the default hint value in subsequent vdev operations
('zpool add', 'attach' and 'replace'). A custom ashift value can still
be specified from the command line, if desired.
Finally, fix a bug in add-o_ashift.ksh caused by a missing variable.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#2024Closes#4205Closes#4740Closes#5763
* Add zfs_nicebytes() to print human-readable sizes
Some 'zfs', 'zpool' and 'zdb' output strings can be confusing to the
user when no units are specified. This add a new zfs_nicenum_format
"ZFS_NICENUM_BYTES" used to print bytes in their human-readable form.
Additionally, update some test cases to use machine-parsable 'zfs get'.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#2414Closes#3185Closes#3594Closes#6032
OpenZFS 7252 - compressed zfs send / receive
OpenZFS 7628 - create long versions of ZFS send / receive options
Authored by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: Sebastien Roy <sebastien.roy@delphix.com>
Reviewed by: David Quigley <dpquigl@davequigley.com>
Reviewed by: Thomas Caputi <tcaputi@datto.com>
Approved by: Dan McDonald <danmcd@omniti.com>
Reviewed by: David Quigley <dpquigl@davequigley.com>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Ported-by: bunder2015 <omfgbunder@gmail.com>
Ported-by: Don Brady <don.brady@intel.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Porting Notes:
- Most of 7252 was already picked up during ABD work. This
commit represents the gap from the final commit to openzfs.
- Fixed split_large_blocks check in do_dump()
- An alternate version of the write_compressible() function was
implemented for Linux which does not depend on fio. The behavior
of fio differs significantly based on the exact version.
- mkholes was replaced with truncate for Linux.
OpenZFS-issue: https://www.illumos.org/issues/7252
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/5602294Closes#6067
This patch updates the "zpool status/iostat -c" commands to only run
"pre-baked" scripts from the /etc/zfs/zpool.d directory (or wherever
you install to). The scripts can only be run from -c as an unprivileged
user (unless the ZPOOL_SCRIPTS_AS_ROOT environment var is
set by root). This was done to encourage scripts to be written is such
a way that normal users can use them, and to be cautious. If your
script needs to run a privileged command, consider adding the
appropriate line in /etc/sudoers. See zpool(8) for an example of how
to do this.
The patch also allows the scripts to output custom column names. If
the script outputs a line like:
name=value
then "name" is used for the column name, and "value" is its value.
Multiple columns can be specified by outputting multiple lines. Column
names and values can have spaces. If the value is empty, a dash (-) is
printed instead.
After all the "name=value" lines are read (if any), zpool will take the
next the next line of output (if any) and print it without a column
header. After that, no more lines will be processed. This can be
useful for printing errors.
Lastly, this patch also disables the -c option with the latency and
request size histograms, since it produced awkward output and made the
code harder to maintain.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#5852
* bookmarks are not supported when sending all intermediary snaps (-I)
* add missing compressed (-c) option to the 'zfs' help and manpage
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Richard Laager <rlaager@wiktel.com>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#6028
Udev may fail to create the expected symbolic links in
/dev/disk/by-vdev on systems with the
device-mapper-multipath-0.4.9-100.el6 package installed. This affects
RHEL 6.9 and possibly other downstream distributions.
That version of the multipath command may incorrectly list a drive
state as "unkown" instead of "running". The issue was introduced
in the patch for https://bugzilla.redhat.com/show_bug.cgi?id=1401769
The vdev_id udev helper uses the state reported by "multipath -l" to
detect an online component disk of a multipath device in order to
resolve its physical slot and enclosure. Changing the command
invocation to "multipath -ll" works around the above issue by causing
multipath to consult additional sources of information to determine
the drive state.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Ned Bass <bass6@llnl.gov>
Closes#6039
This lets users create a bookmark from the command line by its name
only, without the need to specify the dataset path which is extacted
from the snapshot parameter.
These commands are now equivalent:
zfs bookmark poolname/fs@snap poolname/fs#bookmark
zfs bookmark @snap poolname/fs#bookmark
zfs bookmark poolname/fs@snap \#bookmark
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#3665Closes#6027
Authored by: Richard Yao <ryao@gentoo.org>
Approved by: Dan McDonald <danmcd@omniti.com>
Reviewed by: Yuri Pankov <yuri.pankov@gmail.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Porting Notes:
This was already implemented in ZFS on Linux. This patch
is to resolved the deltas present in our version.
OpenZFS-issue: https://www.illumos.org/issues/6392
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/9bb97deCloses#6020
Authored by: Alan Somers <asomers@gmail.com>
Approved by: Dan McDonald <danmcd@omniti.com>
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
There are two reasons:
1) Finding a znode's path is slower than printing any other znode
information at verbosity < 5.
2) On a corrupted pool like the one mentioned below, zdb will crash when it
tries to determine the znode's path. But with this patch, zdb can still
extract useful information from such pools.
OpenZFS-issue: https://www.illumos.org/issues/7900
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/2b0dee1Closes#6016
