Restart a resilver from scratch, if the current one in progress is
below a new tunable, zfs_resilver_defer_percent (defaulting to 10%).
The original rationale for deferring additional resilvers, when there is
already one in progress, was to help achieving data redundancy sooner
for the data that gets scanned at the end of the resilver.
But in case the admin wants to attach multiple disks to a single vdev,
it wasn't immediately obvious the admin is supposed to run
`zpool resilver` afterwards to reset the deferred resilvers and start
a new one from scratch.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Pavel Snajdr <snajpa@snajpa.net>
Closes#15810
In a4b21eadec we added the zap_micro_max_size tuneable to raise the size
at which "micro" (single-block) ZAPs are upgraded to "fat" (multi-block)
ZAPs. Before this, a microZAP was limited to 128KiB, which was the old
largest block size. The side effect of raising the max size past 128KiB
is that it be stored in a large block, requiring the large_blocks
feature.
Unfortunately, this means that a backup stream created without the
--large-block (-L) flag to zfs send would split the microZAP block into
smaller blocks and send those, as is normal behaviour for large blocks.
This would be received correctly, but since microZAPs are limited to the
first block in the object by definition, the entries in the later blocks
would be inaccessible. For directory ZAPs, this gives the appearance of
files being lost.
This commit adds a feature flag, large_microzap, that must be enabled
for microZAPs to grow beyond 128KiB, and which will be activated the
first time that occurs. This feature is later checked when generating
the stream and if active, the send operation will abort unless
--large-block has also been requested.
Changing the limit still requires zap_micro_max_size to be changed. The
state of this flag effectively sets the upper value for this tuneable,
that is, if the feature is disabled, the tuneable will be clamped to
128KiB.
A stream flag is also added to ensure that the receiver also activates
its own feature flag upon receiving the stream. This is not strictly
necessary to _use_ the received microZAP, since it doesn't care how
large its block is, but it is required to send the microZAP object on,
otherwise the original problem occurs again.
Because it's difficult to reliably distinguish a microZAP from a fatZAP
from outside the ZAP code, and because it seems unlikely that most
users are affected (a fairly niche tuneable combined with what should be
an uncommon use of send), and for the sake of expediency, this change
activates the feature the first time a microZAP grows to use a large
block, and is never deactivated after that. This can be improved in the
future.
This commit changes nothing for existing pools that already have large
microZAPs. The feature will not be retroactively applied, but will be
activated the next time a microZAP grows past the limit.
Don't use large_blocks feature for enable/disable tests. The
large_microzap depends on large_blocks, so it gets enabled as a
dependency, breaking the test. Instead use feature "longname", which has
the exact same feature characteristics.
Sponsored-by: Klara, Inc.
Sponsored-by: Wasabi Technology, Inc.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Closes#16593
In some environments, just making the .zfs control dir hidden from sight
might not be enough. In particular, the following scenarios might
warrant not allowing access at all:
- old snapshots with wrong permissions/ownership
- old snapshots with exploitable setuid/setgid binaries
- old snapshots with sensitive contents
Introducing a new 'disabled' value that not only hides the control dir,
but prevents access to its contents by returning ENOENT solves all of
the above.
The new property value takes advantage of 'iuv' semantics ("ignore
unknown value") to automatically fall back to the old default value when
a pool is accessed by an older version of ZFS that doesn't yet know
about 'disabled' semantics.
I think that technically the zfs_dirlook change is enough to prevent
access, but preventing lookups and dir entries in an already opened .zfs
handle might also be a good idea to prevent races when modifying the
property at runtime.
Add zfs_snapshot_no_setuid parameter to control whether automatically
mounted snapshots have the setuid mount option set or not.
this could be considered a partial fix for one of the scenarios
mentioned in desired.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Signed-off-by: Fabian Grünbichler <f.gruenbichler@proxmox.com>
Co-authored-by: Fabian Grünbichler <f.gruenbichler@proxmox.com>
Closes#3963Closes#16587
This patch adds the ability for zfs to support file/dir name up to 1023
bytes. This number is chosen so we can support up to 255 4-byte
characters. This new feature is represented by the new feature flag
feature@longname.
A new dataset property "longname" is also introduced to toggle longname
support for each dataset individually. This property can be disabled,
even if it contains longname files. In such case, new file cannot be
created with longname but existing longname files can still be looked
up.
Note that, to my knowledge native Linux filesystems don't support name
longer than 255 bytes. So there might be programs not able to work with
longname.
Note that NFS server may needs to use exportfs_get_name to reconnect
dentries, and the buffer being passed is limit to NAME_MAX+1 (256). So
NFS may not work when longname is enabled.
Note, FreeBSD vfs layer imposes a limit of 255 name lengh, so even
though we add code to support it here, it won't actually work.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Chunwei Chen <david.chen@nutanix.com>
Closes#15921
Reflect f2330bd156
change in our man pages and add some context.
Wording is primarily copy-pasted from code comments.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Signed-off-by: George Melikov <mail@gmelikov.ru>
Closes#16581
It's the main recommendation to set xattr=sa
even in man pages, so let's set it by default.
xattr=sa don't use feature flag, so in the worst
case we'll have non-readable xattrs by other
non-openzfs platforms.
Non-overridden default `xattr` prop of existing pools
will automatically use `sa` after this commit too.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Melikov <mail@gmelikov.ru>
Closes#15147
GRUB is not able to detect ZFS pool if snaphsot of top level boot
pool is created. This issue is observed with GRUB versions up to
v2.06 if extensible_dataset feature is enabled on ZFS boot pool.
compatibility=grub2-2.06 would enable all read-only compatible
zpool features except extensible_dataset and other features that
depend on it.
The existing grub2 compatibility file is now renamed to grub2-2.12 to
reflect the appropriate grub2 version. grub2-2.12 lists all read-only
features that can be enabled on boot pool for grub2 with version 2.12
onwards.
A new symlink grub2 is created that currently points to the grub2-2.12
compatibility file.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Umer Saleem <usaleem@ixsystems.com>
Closes#13873Closes#15261Closes#15909
Now default compression is lz4, which can stop
compression process by itself on incompressible data.
If there are additional size checks -
we will only make our compressratio worse.
New usable compression thresholds are:
- less than BPE_PAYLOAD_SIZE (embedded_data feature);
- at least one saved sector.
Old 12.5% threshold is left to minimize affect
on existing user expectations of CPU utilization.
If data wasn't compressed - it will be saved as
ZIO_COMPRESS_OFF, so if we really need to recompress
data without ashift info and check anything -
we can just compress it with zero threshold.
So, we don't need a new feature flag here!
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: George Melikov <mail@gmelikov.ru>
Closes#9416
Add ARC structural breakdown, ARC types breakdown, ARC states
breakdown similar to arc_summary. Additional cleanups included.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Theera K. <tkittich@hotmail.com>
Closes#16509
Adding O_DIRECT support to ZFS to bypass the ARC for writes/reads.
O_DIRECT support in ZFS will always ensure there is coherency between
buffered and O_DIRECT IO requests. This ensures that all IO requests,
whether buffered or direct, will see the same file contents at all
times. Just as in other FS's , O_DIRECT does not imply O_SYNC. While
data is written directly to VDEV disks, metadata will not be synced
until the associated TXG is synced.
For both O_DIRECT read and write request the offset and request sizes,
at a minimum, must be PAGE_SIZE aligned. In the event they are not,
then EINVAL is returned unless the direct property is set to always (see
below).
For O_DIRECT writes:
The request also must be block aligned (recordsize) or the write
request will take the normal (buffered) write path. In the event that
request is block aligned and a cached copy of the buffer in the ARC,
then it will be discarded from the ARC forcing all further reads to
retrieve the data from disk.
For O_DIRECT reads:
The only alignment restrictions are PAGE_SIZE alignment. In the event
that the requested data is in buffered (in the ARC) it will just be
copied from the ARC into the user buffer.
For both O_DIRECT writes and reads the O_DIRECT flag will be ignored in
the event that file contents are mmap'ed. In this case, all requests
that are at least PAGE_SIZE aligned will just fall back to the buffered
paths. If the request however is not PAGE_SIZE aligned, EINVAL will
be returned as always regardless if the file's contents are mmap'ed.
Since O_DIRECT writes go through the normal ZIO pipeline, the
following operations are supported just as with normal buffered writes:
Checksum
Compression
Encryption
Erasure Coding
There is one caveat for the data integrity of O_DIRECT writes that is
distinct for each of the OS's supported by ZFS.
FreeBSD - FreeBSD is able to place user pages under write protection so
any data in the user buffers and written directly down to the
VDEV disks is guaranteed to not change. There is no concern
with data integrity and O_DIRECT writes.
Linux - Linux is not able to place anonymous user pages under write
protection. Because of this, if the user decides to manipulate
the page contents while the write operation is occurring, data
integrity can not be guaranteed. However, there is a module
parameter `zfs_vdev_direct_write_verify` that controls the
if a O_DIRECT writes that can occur to a top-level VDEV before
a checksum verify is run before the contents of the I/O buffer
are committed to disk. In the event of a checksum verification
failure the write will return EIO. The number of O_DIRECT write
checksum verification errors can be observed by doing
`zpool status -d`, which will list all verification errors that
have occurred on a top-level VDEV. Along with `zpool status`, a
ZED event will be issues as `dio_verify` when a checksum
verification error occurs.
ZVOLs and dedup is not currently supported with Direct I/O.
A new dataset property `direct` has been added with the following 3
allowable values:
disabled - Accepts O_DIRECT flag, but silently ignores it and treats
the request as a buffered IO request.
standard - Follows the alignment restrictions outlined above for
write/read IO requests when the O_DIRECT flag is used.
always - Treats every write/read IO request as though it passed
O_DIRECT and will do O_DIRECT if the alignment restrictions
are met otherwise will redirect through the ARC. This
property will not allow a request to fail.
There is also a module parameter zfs_dio_enabled that can be used to
force all reads and writes through the ARC. By setting this module
parameter to 0, it mimics as if the direct dataset property is set to
disabled.
Reviewed-by: Brian Behlendorf <behlendorf@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Atkinson <batkinson@lanl.gov>
Co-authored-by: Mark Maybee <mark.maybee@delphix.com>
Co-authored-by: Matt Macy <mmacy@FreeBSD.org>
Co-authored-by: Brian Behlendorf <behlendorf@llnl.gov>
Closes#10018
Requires the new 'flat' physical data which has the start
time for a class entry.
The amount to prune can be based on a target percentage of
the unique entries or based on the age (i.e., every entry
older than N days).
Sponsored-by: Klara, Inc.
Sponsored-by: iXsystems, Inc.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@klarasystems.com>
Closes#16277
This commit extends the zpool-reguid(8) command with a -g flag, which
allows the user to specify the GUID to set.
This change also adds some general tests for zpool-reguid(8).
Sponsored-by: Wasabi Technology, Inc.
Sponsored-by: Klara, Inc.
Signed-off-by: Mateusz Piotrowski <0mp@FreeBSD.org>
Reviewed-by: Rob Norris <rob.norris@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
zfs_arc_shrinker_limit (default: 10000) avoids ARC collapse
due to excessive memory reclaim. However, when the kernel is
in direct reclaim mode (ie: low on memory), limiting ARC reclaim
increases OOM risk. This is especially true on system without
(or with inadequate) swap.
This patch ignores zfs_arc_shrinker_limit when the kernel is in
direct reclaim mode, avoiding most OOM. It also restores
"echo 3 > /proc/sys/vm/drop_caches" ability to correctly drop
(almost) all ARC.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Adam Moss <c@yotes.com>
Signed-off-by: Gionatan Danti <g.danti@assyoma.it>
Closes#16313
These had minimal useful information for the admin, didn't work properly
in some places, and knew far too much about taskq internals.
With the new stats available, these should never be needed anymore.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Sponsored-by: Klara, Inc.
Sponsored-by: Syneto
Closes#16171
`l2arc_mfuonly` was added to avoid wasting L2 ARC on read-once MRU
data and metadata. However it can be useful to cache as much
metadata as possible while, at the same time, restricting data
cache to MFU buffers only.
This patch allow for such behavior by setting `l2arc_mfuonly` to 2
(or higher). The list of possible values is the following:
0: cache both MRU and MFU for both data and metadata;
1: cache only MFU for both data and metadata;
2: cache both MRU and MFU for metadata, but only MFU for data.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Gionatan Danti <g.danti@assyoma.it>
Closes#16343Closes#16402
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Closes#15895
Adds a log/journal to dedup. At the end of txg, instead of writing the
entry directly to the ZAP, instead its adding to an in-memory tree and
appended to an on-disk object. The on-disk object is only read at
import, to reload the in-memory tree.
Lookups first go the the log tree before going to the ZAP, so
recently-used entries will remain close by in memory. This vastly
reduces overhead from dedup IO, as it will not have to do so many
read/update/write cycles on ZAP leaf nodes.
A flushing facility is added at end of txg, to push logged entries out
to the ZAP. There's actually two separate "logs" (in-memory tree and
on-disk object), one active (recieving updated entries) and one flushing
(writing out to disk). These are swapped (ie flushing begins) based on
memory used by the in-memory log trees and time since we last flushed
something.
The flushing facility monitors the amount of entries coming in and being
flushed out, and calibrates itself to try to flush enough each txg to
keep up with the ingest rate without competing too much with other IO.
Multiple tuneables are provided to control the flushing facility.
All the histograms and stats are update to accomodate the log as a
separate entry store. zdb gains knowledge of how to count them and dump
them. Documentation included!
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Sponsored-by: Klara, Inc.
Sponsored-by: iXsystems, Inc.
Closes#15895
This is the supporting infrastructure for the upcoming dedup features.
Traditionally, dedup objects live directly in the MOS root. While their
details vary (checksum, type and class), they are all the same "kind" of
thing - a store of dedup entries.
The new features are more varied than that, and are better thought of as
a set of related stores for the overall state of a dedup table.
This adds a new feature flag, SPA_FEATURE_FAST_DEDUP. Enabling this will
cause new DDTs to be created as a ZAP in the MOS root, named
DDT-<checksum>. The is used as the root object for the normal type/class
store objects, but will also be a place for any storage required by new
features.
This commit adds two new fields to ddt_t, for version and flags. These
are intended to describe the structure and features of the overall dedup
table, and are stored as-is in the DDT root. In this commit, flags are
always zero, but the intent is that they can be used to hang optional
logic or state onto for new dedup features. Version is always 1.
For a "legacy" dedup table, where no DDT root directory exists, the
version will be 0.
ddt_configure() is expected to determine the version and flags features
currently in operation based on whether or not the fast_dedup feature is
enabled, and from what's available on disk. In this way, its possible to
support both old and new tables.
This also provides a migration path. A legacy setup can be upgraded to
FDT by creating the DDT root ZAP, moving the existing objects into it,
and setting version and flags appropriately. There's no support for that
here, but it would be straightforward to add later and allows the
possibility that newer features could be applied to existing dedup
tables.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Sponsored-by: Klara, Inc.
Sponsored-by: iXsystems, Inc.
Closes#15892
The documentation mentioned that the property name can be 256 characters
long. This was incorrect. The last byte is reserved for NUL, so the
name provided by the operator can be only 255 characters long.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Mateusz Piotrowski <0mp@FreeBSD.org>
Sponsored-by: Klara, Inc.
Sponsored-by: Wasabi Technology, Inc.
Closes#16248
This commit adds support for zpool status command to displpay status
of ZFS pools in JSON format using '-j' option. Status information is
collected in nvlist which is later dumped on stdout in JSON format.
Existing options for zpool status work with '-j' flag. man page for
zpool status is updated accordingly.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Ameer Hamza <ahamza@ixsystems.com>
Signed-off-by: Umer Saleem <usaleem@ixsystems.com>
Closes#16217
This commit adds support for zpool list command to output the list of
ZFS pools in JSON format using '-j' option.. Information about available
pools is collected in nvlist which is later printed to stdout in JSON
format.
Existing options for zfs list command work with '-j' flag. man page for
zpool list is updated accordingly.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Ameer Hamza <ahamza@ixsystems.com>
Signed-off-by: Umer Saleem <usaleem@ixsystems.com>
Closes#16217
This commit adds support for zpool get command to output the list of
properties for ZFS Pools and VDEVS in JSON format using '-j' option.
Man page for zpool get is updated to include '-j' option.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Ameer Hamza <ahamza@ixsystems.com>
Signed-off-by: Umer Saleem <usaleem@ixsystems.com>
Closes#16217
This commit adds support for zpool version to output in JSON format
using '-j' option. Userland kernel module version is collected in nvlist
which is later displayed in JSON format. man page for zpool is updated.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Ameer Hamza <ahamza@ixsystems.com>
Signed-off-by: Umer Saleem <usaleem@ixsystems.com>
Closes#16217
This commit adds support for zfs mount to display mounted file systems
in JSON format using '-j' option. Data is collected in nvlist which is
printed in JSON format. man page for zfs mount is updated accordingly.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Ameer Hamza <ahamza@ixsystems.com>
Signed-off-by: Umer Saleem <usaleem@ixsystems.com>
Closes#16217
This commit adds support for JSON output for zfs list using '-j' option.
Information is collected in JSON format which is later printed in jSON
format. Existing options for zfs list also work with '-j'. man pages are
updated with relevant information.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Ameer Hamza <ahamza@ixsystems.com>
Signed-off-by: Umer Saleem <usaleem@ixsystems.com>
Closes#16217
This commit adds support for JSON output for zfs version and zfs get
commands. '-j' flag can be used to get output in JSON format.
Information is collected in nvlist objects which is later printed in
JSON format. Existing options that work for zfs get and zfs version
also work with '-j' flag.
man pages for zfs get and zfs version are updated accordingly.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Ameer Hamza <ahamza@ixsystems.com>
Signed-off-by: Umer Saleem <usaleem@ixsystems.com>
Closes#16217
This change adds a new `zpool prefetch -t ddt $pool` command which
causes a pool's DDT to be loaded into the ARC. The primary goal is to
remove the need to "warm" a pool's cache before deduplication stops
slowing write performance. It may also provide a way to reload portions
of a DDT if they have been flushed due to inactivity.
Sponsored-by: iXsystems, Inc.
Sponsored-by: Catalogics, Inc.
Sponsored-by: Klara, Inc.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Will Andrews <will.andrews@klarasystems.com>
Signed-off-by: Fred Weigel <fred.weigel@klarasystems.com>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Signed-off-by: Don Brady <don.brady@klarasystems.com>
Co-authored-by: Will Andrews <will.andrews@klarasystems.com>
Co-authored-by: Don Brady <don.brady@klarasystems.com>
Closes#15890
- When receiving memory pressure signal from OS be more strict
trying to free some memory. Otherwise kernel may come again and
request much more. Return as result how much arc_c was actually
reduced due to this request, that may be less than requested.
- On Linux when receiving direct reclaim from some file system
(that may be ZFS) instead of ignoring request completely, just
shrink the ARC, but do not wait for eviction. Waiting there may
cause deadlock. Ignoring it as before may put extra pressure on
other caches and/or swap, and cause OOM if nothing help. While
not waiting may result in more ARC evicted later, and may be too
late if OOM killer activate right now, but I hope it to be better
than doing nothing at all.
- On Linux set arc_no_grow before waiting for reclaim, not after,
or it may grow back while we are waiting.
- On Linux add new parameter zfs_arc_shrinker_seeks to balance
ARC eviction cost, relative to page cache and other subsystems.
- Slightly update Linux arc_set_sys_free() math for new kernels.
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Reviewed-by: Rob Norris <rob.norris@klarasystems.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
This adds two new pool properties:
- dedup_table_size, the total size of all DDTs on the pool; and
- dedup_table_quota, the maximum possible size of all DDTs in the pool
When set, quota will be enforced by checking when a new entry is about
to be created. If the pool is over its dedup quota, the entry won't be
created, and the corresponding write will be converted to a regular
non-dedup write. Note that existing entries can be updated (ie their
refcounts changed), as that reuses the space rather than requiring more.
dedup_table_quota can be set to 'auto', which will set it based on the
size of the devices backing the "dedup" allocation device. This makes it
possible to limit the DDTs to the size of a dedup vdev only, such that
when the device fills, no new blocks are deduplicated.
Sponsored-by: iXsystems, Inc.
Sponsored-By: Klara Inc.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Signed-off-by: Don Brady <don.brady@klarasystems.com>
Co-authored-by: Don Brady <don.brady@klarasystems.com>
Co-authored-by: Rob Wing <rob.wing@klarasystems.com>
Co-authored-by: Sean Eric Fagan <sean.fagan@klarasystems.com>
Closes#15889
There has been a bugzilla PR#147881 requesting this
for a long time (14 years!). It extends the syntax of
the ZFS shanenfs property (for FreeBSD only) to allow
multiple sets of options for different hosts/nets,
separated by ';'s.
Signed-off-by: Rick Macklem <rmacklem@FreeBSD.org>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Sponsored-by: Klara, Inc.
Sponsored-By: Wasabi Technology, Inc.
Signed-off-by: Don Brady <don.brady@klarasystems.com>
Co-authored-by: Don Brady <don.brady@klarasystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
This commit fixes what is probably a copy-paste mistake. The
`dracut.zfs` manpage claims that the `bootfs.rollback` option executes
`zfs snapshot -Rf`. `zfs snapshot` does not have a `-R` option. `zfs
rollback` does.
Signed-off-by: Alphan Yılmaz <alphanyilmaz@gmail.com>
Reviewed-by: Rob Norris <rob.norris@klarasystems.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
The ZFS module parameter name is zfs_prefetch_disable, not
zfs_disable_prefetch.
Signed-off-by: Peter Doherty <peterd@acranox.org>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Sponsored-by: Klara, Inc.
Sponsored-by: Wasabi Technology, Inc.
Signed-off-by: Mateusz Piotrowski <0mp@FreeBSD.org>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Sponsored-by: Klara, Inc.
Sponsored-By: Wasabi Technology, Inc.
Signed-off-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Optionally turn off disk's enclosure slot if an I/O is hung
triggering the deadman.
It's possible for outstanding I/O to a misbehaving SCSI disk to
neither promptly complete or return an error. This can occur due
to retry and recovery actions taken by the SCSI layer, driver, or
disk. When it occurs the pool will be unresponsive even though
there may be sufficient redundancy configured to proceeded without
this single disk.
When a hung I/O is detected by the kmods it will be posted as a
deadman event. By default an I/O is considered to be hung after
5 minutes. This value can be changed with the zfs_deadman_ziotime_ms
module parameter. If ZED_POWER_OFF_ENCLOSURE_SLOT_ON_DEADMAN is set
the disk's enclosure slot will be powered off causing the outstanding
I/O to fail. The ZED will then handle this like a normal disk failure.
By default ZED_POWER_OFF_ENCLOSURE_SLOT_ON_DEADMAN is not set.
As part of this change `zfs_deadman_events_per_second` is added
to control the ratelimitting of deadman events independantly of
delay events. In practice, a single deadman event is sufficient
and more aren't particularly useful.
Alphabetize the zfs_deadman_* entries in zfs.4.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#16226
High priority threads are handling ZIL writes. While there is no
ZIL compression, there is encryption, checksuming and RAIDZ math.
We've found that on large systems 1 taskq with 5 threads can be
a bottleneck for throughput, IOPS or both. Instead of just bumping
number of threads with a risk of overloading CPUs and increasing
latency, switch to using TQ_FRONT mechanism to increase sync write
requests priority within standard write threads. Do not do it on
Illumos, since its TQ_FRONT implementation is inherently unfair.
FreeBSD and Linux don't have this problem, so we can do it there.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Rob Norris <robn@despairlabs.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#16146
- Reduce number of allocators on small system down to one per 4
CPU cores, keeping maximum at 4 on 16+ core systems. Small systems
should not have the lock contention multiple allocators supposed
to solve, while having several metaslabs open and modified each
TXG is not free.
- Reduce number of write issue taskqs down to one per 16 CPU
cores and an integer fraction of number of allocators. On mid-
sized systems, where multiple allocators already make sense, too
many write issue taskqs may reduce write speed on single-file
workloads, since single file is handled by only one taskq to
reduce fragmentation. On large systems, that can actually benefit
from many taskq's better IOPS, the bottleneck is less important,
since in worst case there will be at least 16 cores to handle it.
- Distribute dnodes between allocators (and taskqs) in a round-
robin fashion instead of relying on sync taskqs to be balanced.
The last is not guarantied and may depend on scheduling.
- Remove io_wr_iss_tq from struct zio. io_allocator is enough.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#16130
Simplify vdev probes in the zio_vdev_io_done context to
avoid holding the spa config lock for a long duration.
Also allow zpool clear if no evidence of another host
is using the pool.
Sponsored-by: Klara, Inc.
Sponsored-by: Wasabi Technology, Inc.
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@klarasystems.com>
Closes#15839
This allows ZAPs to shrink. When there are two empty sibling leafs,
one of them is collapsed and its storage space is reused.
This improved performance on directories that at one time contained
a large number of files, but many or all of those files have since
been deleted.
This also applies to all other types of ZAPs as well.
Sponsored-by: iXsystems, Inc.
Sponsored-by: Klara, Inc.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Alexander Stetsenko <alex.stetsenko@klarasystems.com>
Closes#15888
There is no reason for these module parameters to be read-only.
Being modified they just apply on next pool import/creation, that
is useful for testing different values.
Reviewed-by: Rich Ercolani <rincebrain@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#16118
Make `zfs get` accept `fs` for `filesystem` and `vol` for `volume`.
Reviewed-by: Rob Norris <rob.norris@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan <errornointernet@envs.net>
Closes#16117
This commit allow spa_load() to drop the spa_namespace_lock so
that imports can happen concurrently. Prior to dropping the
spa_namespace_lock, the import logic will set the spa_load_thread
value to track the thread which is doing the import.
Consumers of spa_lookup() retain the same behavior by blocking
when either a thread is holding the spa_namespace_lock or the
spa_load_thread value is set. This will ensure that critical
concurrent operations cannot take place while a pool is being
imported.
The zpool command is also enhanced to provide multi-threaded support
when invoking zpool import -a.
Lastly, zinject provides a mechanism to insert artificial delays
when importing a pool and new zfs tests are added to verify parallel
import functionality.
Contributions-by: Don Brady <don.brady@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Wilson <gwilson@delphix.com>
Closes#16093
When injected, this causes the matching IO to appear to succeed, but the
actual work is never submitted to the physical device. This can be used
to simulate a write-back cache servicing a write, but the backing device
has failed and the cache cannot complete the operation in the
background.
Sponsored-by: Klara, Inc.
Sponsored-by: Wasabi Technology, Inc.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Closes#16085
The only possible ioctl is a flush, and any other kind of meta-operation
introduced in the future is likely to have different semantics (much
like trim did). So, lets just call it what it is.
Sponsored-by: Klara, Inc.
Sponsored-by: Wasabi Technology, Inc.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Closes#16064
This commit adds support for mounting a dataset along with all of
it's children with '-R' flag for zfs mount. There can be scenarios
where we want to mount all datasets under one hierarchy instead of
mounting all datasets present on system with '-a' flag.
'-R' flag should work on all root and non-root datasets. Usage
information and man page has been updated for zfs mount. A test
for verifying the behavior for '-R' flag is also added.
Reviewed-by: Ameer Hamza <ahamza@ixsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Umer Saleem <usaleem@ixsystems.com>
Closes#16015
Before this change speculative prefetcher was able to detect a stream
only if all of its accesses are perfectly sequential. It was easy to
implement and is perfectly fine for single-threaded applications.
Unfortunately multi-threaded network servers, such as iSCSI, SMB or
NFS usually have plenty of threads and may often reorder requests,
preventing successful speculation and prefetch.
This change allows speculative prefetcher to detect streams even if
requests are reordered by introducing a list of 9 non-contiguous
ranges up to 16MB ahead of current stream position and filling the
gaps as more requests arrive. It also allows stream to proceed
even with holes up to a certain configurable threshold (25%).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#16022
Adds 'ioctl' as a valid IO type for device error injection, so we can
simulate a flush error (which OpenZFS currently ignores, but that's by
the by).
To support this, adding ZIO_STAGE_VDEV_IO_DONE to ZIO_IOCTL_PIPELINE,
since that's where device error injection happens. This needs a small
exclusion to avoid the vdev_queue, since flushes are not queued, and I'm
assuming that the various failure responses are still reasonable for
flush failures (probes, media change, etc). This seems reasonable to me,
as a flush failure is not unlike a write failure in this regard, however
this may be too aggressive or subtle to assume in just this change.
Sponsored-by: Klara, Inc.
Sponsored-by: Wasabi Technology, Inc.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Closes#16061
Currently, zvol uses a single taskq, resulting in throughput bottleneck
under heavy load due to lock contention on the single taskq. This patch
addresses the performance bottleneck under heavy load conditions by
utilizing multiple taskqs, thus mitigating lock contention. The number
of taskqs scale dynamically based on the available CPUs in the system,
as illustrated below:
taskq total
cpus taskqs threads threads
------- ------- ------- -------
1 1 32 32
2 1 32 32
4 1 32 32
8 2 16 32
16 3 11 33
32 5 7 35
64 8 8 64
128 11 12 132
256 16 16 256
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#15992
The commit b53077a added zfs_prepare_disk.8 to the wrong list
dist_man_MANS, in which @zfsexecdir@ will not be properly substituted.
This leads to wrong path in the manpage in generated release tarballs.
Reported-by: Benda Xu <orv@debian.org>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Shengqi Chen <harry-chen@outlook.com>
Closes#15979
