Currently, there is an issue in the raw receive code where
raw receives are allowed to happen on top of previously
non-raw received datasets. This is a problem because the
source-side dataset doesn't know about how the blocks on
the destination were encrypted. As a result, any MAC in
the objset's checksum-of-MACs tree that is a parent of both
blocks encrypted on the source and blocks encrypted by the
destination will be incorrect. This will result in
authentication errors when we decrypt the dataset.
This patch fixes this issue by adding a new check to the
raw receive code. The code now maintains an "IVset guid",
which acts as an identifier for the set of IVs used to
encrypt a given snapshot. When a snapshot is raw received,
the destination snapshot will take this value from the
DRR_BEGIN payload. Non-raw receives and normal "zfs snap"
operations will cause ZFS to generate a new IVset guid.
When a raw incremental stream is received, ZFS will check
that the "from" IVset guid in the stream matches that of
the "from" destination snapshot. If they do not match, the
code will error out the receive, preventing the problem.
This patch requires an on-disk format change to add the
IVset guids to snapshots and bookmarks. As a result, this
patch has errata handling and a tunable to help affected
users resolve the issue with as little interruption as
possible.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#8308
note: which is non-standard. Use builtin 'command -v' instead. [SC2230]
note: Use -n instead of ! -z. [SC2236]
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <guss80@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: bunder2015 <omfgbunder@gmail.com>
Closes#8367
The zpool iostat latency histograms (-w) has column names
'sync_queue' and 'async_queue', which do not match the man page, nor
the equivalent columns in average latency. Change the column
names to be 'syncq_wait' and 'asyncq_wait' to be consistent.
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#8338
When `zpool iostat` fills the terminal the headers should be
printed again. `zpool iostat -n` can be used to suppress this.
If the command is not attached to a tty, headers will not be
printed so as to not break existing scripts.
Reviewed-by: Joshua M. Clulow <josh@sysmgr.org>
Reviewed-by: Giuseppe Di Natale <guss80@gmail.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Damian Wojsław <damian@wojslaw.pl>
Closes#8235Closes#8262
Only display the full details of the vdev initialization state
in 'zpool status' output when requested with the -i option.
By default display '(initializing)' after vdevs when they are
being actively initialized. This is consistent with the
established precident of appending '(resilvering), etc' and
fits within the default 80 column terminal width making it
easy to read.
Additionally, updated the 'zpool initialize' documentation to
make it clear the options are mutually exclusive, but allow
duplicate options like all other zfs/zpool commands.
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed-by: George Wilson <george.wilson@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8230
PROBLEM
========
The first access to a block incurs a performance penalty on some platforms
(e.g. AWS's EBS, VMware VMDKs). Therefore we recommend that volumes are
"thick provisioned", where supported by the platform (VMware). This can
create a large delay in getting a new virtual machines up and running (or
adding storage to an existing Engine). If the thick provision step is
omitted, write performance will be suboptimal until all blocks on the LUN
have been written.
SOLUTION
=========
This feature introduces a way to 'initialize' the disks at install or in the
background to make sure we don't incur this first read penalty.
When an entire LUN is added to ZFS, we make all space available immediately,
and allow ZFS to find unallocated space and zero it out. This works with
concurrent writes to arbitrary offsets, ensuring that we don't zero out
something that has been (or is in the middle of being) written. This scheme
can also be applied to existing pools (affecting only free regions on the
vdev). Detailed design:
- new subcommand:zpool initialize [-cs] <pool> [<vdev> ...]
- start, suspend, or cancel initialization
- Creates new open-context thread for each vdev
- Thread iterates through all metaslabs in this vdev
- Each metaslab:
- select a metaslab
- load the metaslab
- mark the metaslab as being zeroed
- walk all free ranges within that metaslab and translate
them to ranges on the leaf vdev
- issue a "zeroing" I/O on the leaf vdev that corresponds to
a free range on the metaslab we're working on
- continue until all free ranges for this metaslab have been
"zeroed"
- reset/unmark the metaslab being zeroed
- if more metaslabs exist, then repeat above tasks.
- if no more metaslabs, then we're done.
- progress for the initialization is stored on-disk in the vdev’s
leaf zap object. The following information is stored:
- the last offset that has been initialized
- the state of the initialization process (i.e. active,
suspended, or canceled)
- the start time for the initialization
- progress is reported via the zpool status command and shows
information for each of the vdevs that are initializing
Porting notes:
- Added zfs_initialize_value module parameter to set the pattern
written by "zpool initialize".
- Added zfs_vdev_{initializing,removal}_{min,max}_active module options.
Authored by: George Wilson <george.wilson@delphix.com>
Reviewed by: John Wren Kennedy <john.kennedy@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: loli10K <ezomori.nozomu@gmail.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Richard Lowe <richlowe@richlowe.net>
Signed-off-by: Tim Chase <tim@chase2k.com>
Ported-by: Tim Chase <tim@chase2k.com>
OpenZFS-issue: https://www.illumos.org/issues/9102
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/c3963210ebCloses#8230
The verbose output of 'zpool list' was not correctly aligned due
to differences in the vdev name lengths. Minimally update the
code the correct the alignment using the same strategy employed
by 'zpool status'.
Missing dashes were added for the empty defaults columns, and
the vdev state is now printed for all vdevs.
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7308Closes#8147
This change allows 'zpool split' to work with whole-disk devices and
updates the ZFS Test Suite with a new script to exercise this
functionality.
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#6643Closes#8133
This patch adds a new slow I/Os (-s) column to zpool status to show the
number of VDEV slow I/Os. This is the number of I/Os that didn't
complete in zio_slow_io_ms milliseconds. It also adds a new parsable
(-p) flag to display exact values.
NAME STATE READ WRITE CKSUM SLOW
testpool ONLINE 0 0 0 -
mirror-0 ONLINE 0 0 0 -
loop0 ONLINE 0 0 0 20
loop1 ONLINE 0 0 0 0
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#7756Closes#6885
Adds a libzutil for utility functions that are common to libzfs and
libzpool consumers (most of what was in libzfs_import.c). This
removes the need for utilities to link against both libzpool and
libzfs.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@delphix.com>
Closes#8050
Currently, if a resilver is triggered for any reason while an
existing one is running, zfs will immediately restart the existing
resilver from the beginning to include the new drive. This causes
problems for system administrators when a drive fails while another
is already resilvering. In this case, the optimal thing to do to
reduce risk of data loss is to wait for the current resilver to end
before immediately replacing the second failed drive, which allows
the system to operate with two incomplete drives for the minimum
amount of time.
This patch introduces the resilver_defer feature that essentially
does this for the admin without forcing them to wait and monitor
the resilver manually. The change requires an on-disk feature
since we must mark drives that are part of a deferred resilver in
the vdev config to ensure that we do not assume they are done
resilvering when an existing resilver completes.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: @mmaybee
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#7732
ZFS allows, by default, sharing of spare devices among different pools;
this commit simply restores this functionality for disk devices and
adds an additional tests case to the ZFS Test Suite to prevent future
regression.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#7999
Historically, zpool status prints "(repairing)" for any drives that
have errors during a scrub:
NAME STATE READ WRITE CKSUM
mypool ONLINE 0 0 0
mirror-0 ONLINE 0 0 0
/tmp/file1 ONLINE 13 0 0 (repairing)
/tmp/file2 ONLINE 0 0 0
/tmp/file3 ONLINE 0 0 0
This was accidentally broken in "OpenZFS 9166 - zfs storage pool
checkpoint" (d2734cc). This patch adds it back in.
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#7779Closes#7978
Bandwidth and iops are average per second while *_wait are averages
per request for latency or, for queue depths, an instantaneous
measurement at the end of an interval (according to man zpool).
When calculating the first two it makes sense to do
x/interval_duration (x being the increase in total bytes or number of
requests over the duration of the interval, interval_duration in
seconds) to 'scale' from amount/interval_duration to amount/second.
But applying the same math for the latter (*_wait latencies/queue) is
wrong as there is no interval_duration component in the values (these
are time/requests to get to average_time/request or already an
absulute number).
This bug leads to the only correct continuous *_wait figures for both
latencies and queue depths from 'zpool iostat -l/q' being with
duration=1 as then the wrong math cancels itself (x/1 is a nop).
This removes temporal scaling from latency and queue depth figures.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Gregor Kopka <gregor@kopka.net>
Closes#7945Closes#7694
This change improve the handling of invalid filesystem properties when
specified at pool creation: this is useful when 'zpool create -n'
(dry run) is executed to detect invalid fs-level options (-O) before
the actual command is run.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#7620Closes#7878
Allocation Classes add the ability to have allocation classes in a
pool that are dedicated to serving specific block categories, such
as DDT data, metadata, and small file blocks. A pool can opt-in to
this feature by adding a 'special' or 'dedup' top-level VDEV.
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Alek Pinchuk <apinchuk@datto.com>
Reviewed-by: Håkan Johansson <f96hajo@chalmers.se>
Reviewed-by: Andreas Dilger <andreas.dilger@chamcloud.com>
Reviewed-by: DHE <git@dehacked.net>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: Gregor Kopka <gregor@kopka.net>
Reviewed-by: Kash Pande <kash@tripleback.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Don Brady <don.brady@delphix.com>
Closes#5182
argv[] gets modified during string parsing for input arguments. This
is reflected in the live process listing. Don't do that.
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Giuseppe Di Natale <guss80@gmail.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: DHE <git@dehacked.net>
Closes#7760
= Motivation
While dealing with another performance issue (see 126118f) we noticed
that we spend a lot of time in various places in the kernel when
constructing long nvlists. The problem is that when an nvlist is created
with the NV_UNIQUE_NAME set (which is the case most of the time), we do
a linear search through the whole list to ensure uniqueness for every
entry we add.
An example of the above scenario can be seen in the following
flamegraph, where more than have the time of the zfsdev_ioctl() is spent
on constructing nvlists. Flamegraph:
https://sdimitro.github.io/img/flame/sdimitro_snap_unmount3.svg
Adding a table to speed up lookups will help situations where we just
construct an nvlist (like the scenario above), in addition to regular
lookups and removals.
= What this patch does
In this diff we've implemented a hash-table on top of the nvlist code
that converts most nvlist operations from O(# number of entries) to
O(1)* (the start is for amortized time as the hash-table grows and
shrinks depending on the # of entries - plain lookup is strictly O(1)).
= Performance Analysis
To analyze the performance improvement I just used the setup from the
snapshot deletion issue mentioned above in the Motivation section.
Basically I created 10K filesystems with one snapshot each and then I
just used the API of libZFS_Core to pass down an nvlist of all the
snapshots to have them deleted. The reason I used my own driver program
was to have clean performance results of what actually happens in the
kernel. The flamegraphs and wall clock times mentioned below were
gathered from the start to the end of the driver program's run. Between
trials the testpool used was completely destroyed, the system was
rebooted and the testpool was completely recreated. The reason for this
dance was to get consistent results.
== Results (before patch):
=== Sampling Flamegraphs
[Trial 1] https://sdimitro.github.io/img/flame/DLPX-53417/trial-A.svg
[Trial 2] https://sdimitro.github.io/img/flame/DLPX-53417/trial-A2.svg
[Trial 3] https://sdimitro.github.io/img/flame/DLPX-53417/trial-A3.svg
=== Wall clock times (in seconds)
```
[Trial 4]
real 5.3
user 0.4
sys 2.3
[Trial 5]
real 8.2
user 0.4
sys 2.4
[Trial 6]
real 6.0
user 0.5
sys 2.3
```
== Results (after patch):
=== Sampling Flamegraphs
[Trial 1] https://sdimitro.github.io/img/flame/DLPX-53417/trial-Ae.svg
[Trial 2] https://sdimitro.github.io/img/flame/DLPX-53417/trial-A2e.svg
[Trial 3] https://sdimitro.github.io/img/flame/DLPX-53417/trial-A3e.svg
=== Wall clock times (in seconds)
```
[Trial 4]
real 4.9
user 0.0
sys 0.9
[Trial 5]
real 3.8
user 0.0
sys 0.9
[Trial 6]
real 3.6
user 0.0
sys 0.9
```
== Analysis
The results between the trials are consistent so in this sections I will
only talk about the flamegraph results from trial-1 and the wall-clock
results from trial-4.
From trial-1 we can see that zfs_dev_ioctl() goes from 2,331 to 996
samples counts. Specifically, the samples from fnvlist_add_nvlist() and
spa_history_log_nvl() are almost gone (~500 & ~800 to 5 & 5 samples),
leaving zfs_ioc_destroy_snaps() to dominate most samples from
zfs_dev_ioctl().
From trial-4 we see that the user time dropped to 0 secods. I believe
the consistent 0.4 seconds before my patch was applied was due to my
driver program constructing the long nvlist of snapshots so it can pass
it to the kernel. As for the system time, the effect there is more clear
(2.3 down to 0.9 seconds).
Porting Notes:
* DATA_TYPE_DONTCARE case added to switch in fm_nvprintr() and
zpool_do_events_nvprint().
Authored by: Serapheim Dimitropoulos <serapheim.dimitro@delphix.com>
Reviewed by: Matt Ahrens <matt@delphix.com>
Reviewed by: Sebastien Roy <sebastien.roy@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/9580
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/b5eca7b1Closes#7748
Add a default 4 KiB ashift for Amazon EC2 NVMe devices on instances with
NVMe ephemeral devices, such as the types c5d, f1, i3 and m5d.
As per the official documentation [1] a 4096 byte blocksize should be
used to match the underlying hardware.
The string was identified via:
$ sudo sginfo -M /dev/nvme0n1
INQUIRY response (cmd: 0x12)
----------------------------
Device Type 0
Vendor: NVMe
Product: Amazon EC2 NVMe
Revision level:
$ lsblk -io KNAME,TYPE,SIZE,MODEL
KNAME TYPE SIZE MODEL
nvme0n1 disk 442.4G Amazon EC2 NVMe Instance Storage
[1] https://docs.aws.amazon.com/AWSEC2/latest/UserGuide/
storage-optimized-instances.html
Retrived 2018-07-03
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <guss80@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Troels Nørgaard <tnn@tradeshift.com>
Closes#7676
Details about the motivation of this feature and its usage can
be found in this blogpost:
https://sdimitro.github.io/post/zpool-checkpoint/
A lightning talk of this feature can be found here:
https://www.youtube.com/watch?v=fPQA8K40jAM
Implementation details can be found in big block comment of
spa_checkpoint.c
Side-changes that are relevant to this commit but not explained
elsewhere:
* renames members of "struct metaslab trees to be shorter without
losing meaning
* space_map_{alloc,truncate}() accept a block size as a
parameter. The reason is that in the current state all space
maps that we allocate through the DMU use a global tunable
(space_map_blksz) which defauls to 4KB. This is ok for metaslab
space maps in terms of bandwirdth since they are scattered all
over the disk. But for other space maps this default is probably
not what we want. Examples are device removal's vdev_obsolete_sm
or vdev_chedkpoint_sm from this review. Both of these have a
1:1 relationship with each vdev and could benefit from a bigger
block size.
Porting notes:
* The part of dsl_scan_sync() which handles async destroys has
been moved into the new dsl_process_async_destroys() function.
* Remove "VERIFY(!(flags & FWRITE))" in "kernel.c" so zhack can write
to block device backed pools.
* ZTS:
* Fix get_txg() in zpool_sync_001_pos due to "checkpoint_txg".
* Don't use large dd block sizes on /dev/urandom under Linux in
checkpoint_capacity.
* Adopt Delphix-OS's setting of 4 (spa_asize_inflation =
SPA_DVAS_PER_BP + 1) for the checkpoint_capacity test to speed
its attempts to fill the pool
* Create the base and nested pools with sync=disabled to speed up
the "setup" phase.
* Clear labels in test pool between checkpoint tests to avoid
duplicate pool issues.
* The import_rewind_device_replaced test has been marked as "known
to fail" for the reasons listed in its DISCLAIMER.
* New module parameters:
zfs_spa_discard_memory_limit,
zfs_remove_max_bytes_pause (not documented - debugging only)
vdev_max_ms_count (formerly metaslabs_per_vdev)
vdev_min_ms_count
Authored by: Serapheim Dimitropoulos <serapheim.dimitro@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Richard Lowe <richlowe@richlowe.net>
Ported-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Tim Chase <tim@chase2k.com>
OpenZFS-issue: https://illumos.org/issues/9166
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/7159fdb8Closes#7570
zpool and zed place scripts in subdirectories of libexecdir. Some
distributions locate architecture independent scripts in other locations
(e.g. Debian). To avoid these paths getting out of sync, centralize the
definitions.
Build zfs-test's default.cfg by Makefile. Use the new directory
logic building tests/zfs-tests/include/default.cfg.in.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Antonio Russo <antonio.e.russo@gmail.com>
Closes#7597
1. Add a proc entry to display the pool's state:
$ cat /proc/spl/kstat/zfs/tank/state
ONLINE
This is done without using the spa config locks, so it will
never hang.
2. Fix 'zpool status' and 'zpool list -o health' output to print
"SUSPENDED" instead of "ONLINE" for suspended pools.
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Richard Elling <Richard.Elling@RichardElling.com>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#7331Closes#7563
We want to be able to pass various settings during import/open of a
pool, which are not only related to rewind. Instead of adding a new
policy and duplicate a bunch of code, we should just rename
rewind_policy to a more generic term like load_policy.
For instance, we'd like to set spa->spa_import_flags from the nvlist,
rather from a flags parameter passed to spa_import as in some cases we
want those flags not only for the import case, but also for the open
case. One such flag could be ZFS_IMPORT_MISSING_LOG (as used in zdb)
which would allow zfs to open a pool when logs are missing.
Authored by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: Matt Ahrens <matt@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://illumos.org/issues/9235
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/d2b1e44Closes#7532
Some work has been done lately to improve the debugability of the ZFS pool
load (and import) process. This includes:
7638 Refactor spa_load_impl into several functions
8961 SPA load/import should tell us why it failed
7277 zdb should be able to print zfs_dbgmsg's
To iterate on top of that, there's a few changes that were made to make the
import process more resilient and crash free. One of the first tasks during the
pool load process is to parse a config provided from userland that describes
what devices the pool is composed of. A vdev tree is generated from that config,
and then all the vdevs are opened.
The Meta Object Set (MOS) of the pool is accessed, and several metadata objects
that are necessary to load the pool are read. The exact configuration of the
pool is also stored inside the MOS. Since the configuration provided from
userland is external and might not accurately describe the vdev tree
of the pool at the txg that is being loaded, it cannot be relied upon to safely
operate the pool. For that reason, the configuration in the MOS is read early
on. In the past, the two configurations were compared together and if there was
a mismatch then the load process was aborted and an error was returned.
The latter was a good way to ensure a pool does not get corrupted, however it
made the pool load process needlessly fragile in cases where the vdev
configuration changed or the userland configuration was outdated. Since the MOS
is stored in 3 copies, the configuration provided by userland doesn't have to be
perfect in order to read its contents. Hence, a new approach has been adopted:
The pool is first opened with the untrusted userland configuration just so that
the real configuration can be read from the MOS. The trusted MOS configuration
is then used to generate a new vdev tree and the pool is re-opened.
When the pool is opened with an untrusted configuration, writes are disabled
to avoid accidentally damaging it. During reads, some sanity checks are
performed on block pointers to see if each DVA points to a known vdev;
when the configuration is untrusted, instead of panicking the system if those
checks fail we simply avoid issuing reads to the invalid DVAs.
This new two-step pool load process now allows rewinding pools accross
vdev tree changes such as device replacement, addition, etc. Loading a pool
from an external config file in a clustering environment also becomes much
safer now since the pool will import even if the config is outdated and didn't,
for instance, register a recent device addition.
With this code in place, it became relatively easy to implement a
long-sought-after feature: the ability to import a pool with missing top level
(i.e. non-redundant) devices. Note that since this almost guarantees some loss
of data, this feature is for now restricted to a read-only import.
Porting notes (ZTS):
* Fix 'make dist' target in zpool_import
* The maximum path length allowed by tar is 99 characters. Several
of the new test cases exceeded this limit resulting in them not
being included in the tarball. Shorten the names slightly.
* Set/get tunables using accessor functions.
* Get last synced txg via the "zfs_txg_history" mechanism.
* Clear zinject handlers in cleanup for import_cache_device_replaced
and import_rewind_device_replaced in order that the zpool can be
exported if there is an error.
* Increase FILESIZE to 8G in zfs-test.sh to allow for a larger
ext4 file system to be created on ZFS_DISK2. Also, there's
no need to partition ZFS_DISK2 at all. The partitioning had
already been disabled for multipath devices. Among other things,
the partitioning steals some space from the ext4 file system,
makes it difficult to accurately calculate the paramters to
parted and can make some of the tests fail.
* Increase FS_SIZE and FILE_SIZE in the zpool_import test
configuration now that FILESIZE is larger.
* Write more data in order that device evacuation take lonnger in
a couple tests.
* Use mkdir -p to avoid errors when the directory already exists.
* Remove use of sudo in import_rewind_config_changed.
Authored by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Andrew Stormont <andyjstormont@gmail.com>
Approved by: Hans Rosenfeld <rosenfeld@grumpf.hope-2000.org>
Ported-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Tim Chase <tim@chase2k.com>
OpenZFS-issue: https://illumos.org/issues/9075
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/619c0123Closes#7459
OpenZFS 7614 - zfs device evacuation/removal
OpenZFS 9064 - remove_mirror should wait for device removal to complete
This project allows top-level vdevs to be removed from the storage pool
with "zpool remove", reducing the total amount of storage in the pool.
This operation copies all allocated regions of the device to be removed
onto other devices, recording the mapping from old to new location.
After the removal is complete, read and free operations to the removed
(now "indirect") vdev must be remapped and performed at the new location
on disk. The indirect mapping table is kept in memory whenever the pool
is loaded, so there is minimal performance overhead when doing operations
on the indirect vdev.
The size of the in-memory mapping table will be reduced when its entries
become "obsolete" because they are no longer used by any block pointers
in the pool. An entry becomes obsolete when all the blocks that use
it are freed. An entry can also become obsolete when all the snapshots
that reference it are deleted, and the block pointers that reference it
have been "remapped" in all filesystems/zvols (and clones). Whenever an
indirect block is written, all the block pointers in it will be "remapped"
to their new (concrete) locations if possible. This process can be
accelerated by using the "zfs remap" command to proactively rewrite all
indirect blocks that reference indirect (removed) vdevs.
Note that when a device is removed, we do not verify the checksum of
the data that is copied. This makes the process much faster, but if it
were used on redundant vdevs (i.e. mirror or raidz vdevs), it would be
possible to copy the wrong data, when we have the correct data on e.g.
the other side of the mirror.
At the moment, only mirrors and simple top-level vdevs can be removed
and no removal is allowed if any of the top-level vdevs are raidz.
Porting Notes:
* Avoid zero-sized kmem_alloc() in vdev_compact_children().
The device evacuation code adds a dependency that
vdev_compact_children() be able to properly empty the vdev_child
array by setting it to NULL and zeroing vdev_children. Under Linux,
kmem_alloc() and related functions return a sentinel pointer rather
than NULL for zero-sized allocations.
* Remove comment regarding "mpt" driver where zfs_remove_max_segment
is initialized to SPA_MAXBLOCKSIZE.
Change zfs_condense_indirect_commit_entry_delay_ticks to
zfs_condense_indirect_commit_entry_delay_ms for consistency with
most other tunables in which delays are specified in ms.
* ZTS changes:
Use set_tunable rather than mdb
Use zpool sync as appropriate
Use sync_pool instead of sync
Kill jobs during test_removal_with_operation to allow unmount/export
Don't add non-disk names such as "mirror" or "raidz" to $DISKS
Use $TEST_BASE_DIR instead of /tmp
Increase HZ from 100 to 1000 which is more common on Linux
removal_multiple_indirection.ksh
Reduce iterations in order to not time out on the code
coverage builders.
removal_resume_export:
Functionally, the test case is correct but there exists a race
where the kernel thread hasn't been fully started yet and is
not visible. Wait for up to 1 second for the removal thread
to be started before giving up on it. Also, increase the
amount of data copied in order that the removal not finish
before the export has a chance to fail.
* MMP compatibility, the concept of concrete versus non-concrete devices
has slightly changed the semantics of vdev_writeable(). Update
mmp_random_leaf_impl() accordingly.
* Updated dbuf_remap() to handle the org.zfsonlinux:large_dnode pool
feature which is not supported by OpenZFS.
* Added support for new vdev removal tracepoints.
* Test cases removal_with_zdb and removal_condense_export have been
intentionally disabled. When run manually they pass as intended,
but when running in the automated test environment they produce
unreliable results on the latest Fedora release.
They may work better once the upstream pool import refectoring is
merged into ZoL at which point they will be re-enabled.
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Alex Reece <alex@delphix.com>
Reviewed-by: George Wilson <george.wilson@delphix.com>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: Richard Laager <rlaager@wiktel.com>
Reviewed by: Tim Chase <tim@chase2k.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Garrett D'Amore <garrett@damore.org>
Ported-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Tim Chase <tim@chase2k.com>
OpenZFS-issue: https://www.illumos.org/issues/7614
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/f539f1ebCloses#6900
When the pool is suspended, record whether it was due to an I/O error or
due to MMP writes failing to succeed within the required time.
Change spa_suspended from uint8_t to zio_suspend_reason_t to store the
reason.
When userspace queries pool status via spa_tryimport(), report the
reason the pool was suspended in a new key,
ZPOOL_CONFIG_SUSPENDED_REASON.
In libzfs, when interpreting the returned config nvlist, report
suspension due to MMP with a new pool status enum value,
ZPOOL_STATUS_IO_FAILURE_MMP.
In status_callback(), which generates and emits the message when 'zpool
status' is executed, add a case to print an appropriate message for the
new pool status enum value.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#7296
get_format_prompt_string() and zpool_state_to_name() return
a string literal which is read-only, thus they should return
`const char*`.
zpool_get_prop_string() returns a non-const string after
successful nv-lookup, and returns a string literal otherwise.
Since this function is designed to be used for read-only purpose,
the return type should also be `const char*`.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@osnexus.com>
Closes#7285
Add in SMART self-test results to zpool status|iostat -c. This
works for both SAS and SATA drives.
Also, add plumbing to allow the 'smart' script to take smartctl
output from a directory of output text files instead of running
it against the vdevs.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#7178
This adds the SMART attributes required to probe Samsung SSD and NVMe
(and possibly others) disks when using the "zpool status -c" command.
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: bunder2015 <omfgbunder@gmail.com>
Closes#7183Closes#7193
Authored by: Chris Williamson <chris.williamson@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Approved by: Garrett D'Amore <garrett@damore.org>
Ported-by: Don Brady <don.brady@delphix.com>
Ported-by: John Kennedy <john.kennedy@delphix.com>
OpenZFS-issue: https://www.illumos.org/issues/7431
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/dfc11533
Porting Notes:
* The CLI long option arguments for '-t' and '-m' don't parse on linux
* Switched from kmem_alloc to vmem_alloc in zcp_lua_alloc
* Lua implementation is built as its own module (zlua.ko)
* Lua headers consumed directly by zfs code moved to 'include/sys/lua/'
* There is no native setjmp/longjump available in stock Linux kernel.
Brought over implementations from illumos and FreeBSD
* The get_temporary_prop() was adapted due to VFS platform differences
* Use of inline functions in lua parser to reduce stack usage per C call
* Skip some ZFS Test Suite ZCP tests on sparc64 to avoid stack overflow
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: DHE <git@dehacked.net>
Closes#7133
The on-disk format for encrypted datasets protects not only
the encrypted and authenticated blocks themselves, but also
the order and interpretation of these blocks. In order to
make this work while maintaining the ability to do raw
sends, the indirect bps maintain a secure checksum of all
the MACs in the block below it along with a few other
fields that determine how the data is interpreted.
Unfortunately, the current on-disk format erroneously
includes some fields which are not portable and thus cannot
support raw sends. It is not possible to easily work around
this issue due to a separate and much smaller bug which
causes indirect blocks for encrypted dnodes to not be
compressed, which conflicts with the previous bug. In
addition, the current code generates incompatible on-disk
formats on big endian and little endian systems due to an
issue with how block pointers are authenticated. Finally,
raw send streams do not currently include dn_maxblkid when
sending both the metadnode and normal dnodes which are
needed in order to ensure that we are correctly maintaining
the portable objset MAC.
This patch zero's out the offending fields when computing
the bp MAC and ensures that these MACs are always
calculated in little endian order (regardless of the host
system's byte order). This patch also registers an errata
for the old on-disk format, which we detect by adding a
"version" field to newly created DSL Crypto Keys. We allow
datasets without a version (version 0) to only be mounted
for read so that they can easily be migrated. We also now
include dn_maxblkid in raw send streams to ensure the MAC
can be maintained correctly.
This patch also contains minor bug fixes and cleanups.
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#6845Closes#6864Closes#7052
* Remove 'zfs snap' from zfs help message (OpenZFS sync)
* Update zfs(8) to suggest 'snap' can be used as an alias for 'snapshot'
* Enforce 80 columns limit in help messages
* Remove zfs_disable_dup_eviction from zfs-module-parameters(5)
* Expose zfs_scan_max_ext_gap as a kernel module parameter.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#7087
usr/src/uts/common/sys/fs/zfs.h
Change ZPROP_INVAL and ZPROP_CONT from macros to enum values. Clang
and GCC both prefer to use unsigned ints to store enums. That was
causing tautological comparison warnings (and likely eliminating
error handling code at compile time) whenever a zfs_prop_t or
zpool_prop_t was compared to ZPROP_INVAL or ZPROP_CONT. Making the
error flags be explicity enum values forces the enum types to be
signed.
ZPROP_INVAL was also compared against two different enum types. I
had to change its name to ZPOOL_PROP_INVAL whenever its compared to
a zpool_prop_t. There are still some places where ZPROP_INVAL or
ZPROP_CONT is compared to a plain int, in code that doesn't know
whether the int is storing a zfs_prop_t or a zpool_prop_t.
usr/src/uts/common/fs/zfs/spa.c
s/ZPROP_INVAL/ZPOOL_PROP_INVAL/
Authored by: Alan Somers <asomers@gmail.com>
Approved by: Gordon Ross <gwr@nexenta.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Igor Kozhukhov <igor@dilos.org>
Reviewed by: George Melikov <mail@gmelikov.ru>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/8652
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/c2de80dc74Closes#7061
Resolved unused variable warnings observed after restricting
-Wno-unused-but-set-variable to only libzfs and libzpool.
Reviewed-by: DHE <git@dehacked.net>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6941
When replacing a faulted device which was previously handled by a spare
multiple levels of nested interior VDEVs will be present in the pool
configuration; the following example illustrates one of the possible
situations:
NAME STATE READ WRITE CKSUM
testpool DEGRADED 0 0 0
raidz1-0 DEGRADED 0 0 0
spare-0 DEGRADED 0 0 0
replacing-0 DEGRADED 0 0 0
/var/tmp/fault-dev UNAVAIL 0 0 0 cannot open
/var/tmp/replace-dev ONLINE 0 0 0
/var/tmp/spare-dev1 ONLINE 0 0 0
/var/tmp/safe-dev ONLINE 0 0 0
spares
/var/tmp/spare-dev1 INUSE currently in use
This is safe and allowed, but get_replication() needs to handle this
situation gracefully to let zpool add new devices to the pool.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#6678Closes#6996
Fix a segfault when running 'zpool iostat -v 1' while adding
a VDEV.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#6748Closes#6872
When the pool configuration contains a hole due to a previous device
removal ignore this top level vdev. Failure to do so will result in
the current configuration being assessed to have a non-uniform
replication level and the expected warning will be disabled.
The zpool_add_010_pos test case was extended to cover this scenario.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6907Closes#6911
Currently, scrubs and resilvers can take an extremely
long time to complete. This is largely due to the fact
that zfs scans process pools in logical order, as
determined by each block's bookmark. This makes sense
from a simplicity perspective, but blocks in zfs are
often scattered randomly across disks, particularly
due to zfs's copy-on-write mechanisms.
This patch improves performance by splitting scrubs
and resilvers into a metadata scanning phase and an IO
issuing phase. The metadata scan reads through the
structure of the pool and gathers an in-memory queue
of I/Os, sorted by size and offset on disk. The issuing
phase will then issue the scrub I/Os as sequentially as
possible, greatly improving performance.
This patch also updates and cleans up some of the scan
code which has not been updated in several years.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Authored-by: Saso Kiselkov <saso.kiselkov@nexenta.com>
Authored-by: Alek Pinchuk <apinchuk@datto.com>
Authored-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#3625Closes#6256
Additionally add four new tests:
* zpool_events_clear: verify 'zpool events -c' functionality
* zpool_events_cliargs: verify command line options and arguments
* zpool_events_follow: verify 'zpool events -f'
* zpool_events_poolname: verify events filtering by pool name
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#3285Closes#6762
Added -n flag to zpool reopen that allows a running scrub
operation to continue if there is a device with Dirty Time Log.
By default if a component device has a DTL and zpool reopen
is executed all running scan operations will be restarted.
Added functional tests for `zpool reopen`
Tests covers following scenarios:
* `zpool reopen` without arguments,
* `zpool reopen` with pool name as argument,
* `zpool reopen` while scrubbing,
* `zpool reopen -n` while scrubbing,
* `zpool reopen -n` while resilvering,
* `zpool reopen` with bad arguments.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: Arkadiusz Bubała <arkadiusz.bubala@open-e.com>
Closes#6076Closes#6746
Currently the 480GB models of this disk do not use ashift=12 by
default. SSDSC2BW48 is also optimized for 4k blocks.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: adisbladis <adis@blad.is>
Closes#6774
CID 161388: Resource Leak (REASOURCE_LEAK)
Jump to errout so that file descriptor gets closed before returning
from function.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Closes#6755
* PBKDF2 implementation changed to OpenSSL implementation.
* HKDF implementation moved to its own file and tests
added to ensure correctness.
* Removed libzfs's now unnecessary dependency on libzpool
and libicp.
* Ztest can now create and test encrypted datasets. This is
currently disabled until issue #6526 is resolved, but
otherwise functions as advertised.
* Several small bug fixes discovered after enabling ztest
to run on encrypted datasets.
* Fixed coverity defects added by the encryption patch.
* Updated man pages for encrypted send / receive behavior.
* Fixed a bug where encrypted datasets could receive
DRR_WRITE_EMBEDDED records.
* Minor code cleanups / consolidation.
Signed-off-by: Tom Caputi <tcaputi@datto.com>
This change incorporates three major pieces:
The first change is a keystore that manages wrapping
and encryption keys for encrypted datasets. These
commands mostly involve manipulating the new
DSL Crypto Key ZAP Objects that live in the MOS. Each
encrypted dataset has its own DSL Crypto Key that is
protected with a user's key. This level of indirection
allows users to change their keys without re-encrypting
their entire datasets. The change implements the new
subcommands "zfs load-key", "zfs unload-key" and
"zfs change-key" which allow the user to manage their
encryption keys and settings. In addition, several new
flags and properties have been added to allow dataset
creation and to make mounting and unmounting more
convenient.
The second piece of this patch provides the ability to
encrypt, decyrpt, and authenticate protected datasets.
Each object set maintains a Merkel tree of Message
Authentication Codes that protect the lower layers,
similarly to how checksums are maintained. This part
impacts the zio layer, which handles the actual
encryption and generation of MACs, as well as the ARC
and DMU, which need to be able to handle encrypted
buffers and protected data.
The last addition is the ability to do raw, encrypted
sends and receives. The idea here is to send raw
encrypted and compressed data and receive it exactly
as is on a backup system. This means that the dataset
on the receiving system is protected using the same
user key that is in use on the sending side. By doing
so, datasets can be efficiently backed up to an
untrusted system without fear of data being
compromised.
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#494Closes#5769
OpenZFS provides a library called tpool which implements thread
pools for user space applications. Porting this library means
the zpool utility no longer needs to borrow the kernel mutex and
taskq interfaces from libzpool. This code was updated to use
the tpool library which behaves in a very similar fashion.
Porting libtpool was relatively straight forward and minimal
modifications were needed. The core changes were:
* Fully convert the library to use pthreads.
* Updated signal handling.
* lmalloc/lfree converted to calloc/free
* Implemented portable pthread_attr_clone() function.
Finally, update the build system such that libzpool.so is no
longer linked in to zfs(8), zpool(8), etc. All that is required
is libzfs to which the zcommon soures were added (which is the way
it always should have been). Removing the libzpool dependency
resulted in several build issues which needed to be resolved.
* Moved zfeature support to module/zcommon/zfeature_common.c
* Moved ratelimiting to to module/zfs/zfs_ratelimit.c
* Moved get_system_hostid() to lib/libspl/gethostid.c
* Removed use of cmn_err() in zcommon source
* Removed dprintf_setup() call from zpool_main.c and zfs_main.c
* Removed highbit() and lowbit()
* Removed unnecessary library dependencies from Makefiles
* Removed fletcher-4 kstat in user space
* Added sha2 support explicitly to libzfs
* Added highbit64() and lowbit64() to zpool_util.c
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6442
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Sen Haerens <sen@senhaerens.be>
Closes#6444Closes#6445
Turning the multihost property on requires that a hostid be set to allow
ZFS to determine when a foreign system is attemping to import a pool.
The error message instructing the user to set a hostid refers to
genhostid(1).
Genhostid(1) is not available on SUSE Linux. This commit adds a script
modeled after genhostid(1) for those users.
Zgenhostid checks for an /etc/hostid file; if it does not exist, it
creates one and stores a value. If the user has provided a hostid as an
argument, that value is used. Otherwise, a random hostid is generated
and stored.
This differs from the CENTOS 6/7 versions of genhostid, which overwrite
the /etc/hostid file even though their manpages state otherwise.
A man page for zgenhostid is added. The one for genhostid is in (1), but
I put zgenhostid in (8) because I believe it's more appropriate.
The mmp tests are modified to use zgenhostid to set the hostid instead
of using the spl_hostid module parameter. zgenhostid will not replace
an existing /etc/hostid file, so new mmp_clear_hostid calls are
required.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#6358Closes#6379
When replacing a disk with non-wholedisk spare, we shouldn't zero_label
it. The wholedisk case already skip it. In fact, zero_label function
will fail saying device busy because it's already opened exclusively,
but since there's no error checking, the replace command will succeed,
causing great confusion.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Closes#6369
zpool iostat/status -c is supposed to be restricted
by its search path, but currently isn't. To prevent
arbitrary scripts from being executed, disallow '/'
from commands.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Ned Bass <bass6@llnl.gov>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#6353Closes#6359
CID 165757: Control flow issues (MISSING_BREAK)
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: George Melikov <mail@gmelikov.ru>
Closes#6348
Add multihost=on|off pool property to control MMP. When enabled
a new thread writes uberblocks to the last slot in each label, at a
set frequency, to indicate to other hosts the pool is actively imported.
These uberblocks are the last synced uberblock with an updated
timestamp. Property defaults to off.
During tryimport, find the "best" uberblock (newest txg and timestamp)
repeatedly, checking for change in the found uberblock. Include the
results of the activity test in the config returned by tryimport.
These results are reported to user in "zpool import".
Allow the user to control the period between MMP writes, and the
duration of the activity test on import, via a new module parameter
zfs_multihost_interval. The period is specified in milliseconds. The
activity test duration is calculated from this value, and from the
mmp_delay in the "best" uberblock found initially.
Add a kstat interface to export statistics about Multiple Modifier
Protection (MMP) updates. Include the last synced txg number, the
timestamp, the delay since the last MMP update, the VDEV GUID, the VDEV
label that received the last MMP update, and the VDEV path. Abbreviated
output below.
$ cat /proc/spl/kstat/zfs/mypool/multihost
31 0 0x01 10 880 105092382393521 105144180101111
txg timestamp mmp_delay vdev_guid vdev_label vdev_path
20468 261337 250274925 68396651780 3 /dev/sda
20468 261339 252023374 6267402363293 1 /dev/sdc
20468 261340 252000858 6698080955233 1 /dev/sdx
20468 261341 251980635 783892869810 2 /dev/sdy
20468 261342 253385953 8923255792467 3 /dev/sdd
20468 261344 253336622 042125143176 0 /dev/sdab
20468 261345 253310522 1200778101278 2 /dev/sde
20468 261346 253286429 0950576198362 2 /dev/sdt
20468 261347 253261545 96209817917 3 /dev/sds
20468 261349 253238188 8555725937673 3 /dev/sdb
Add a new tunable zfs_multihost_history to specify the number of MMP
updates to store history for. By default it is set to zero meaning that
no MMP statistics are stored.
When using ztest to generate activity, for automated tests of the MMP
function, some test functions interfere with the test. For example, the
pool is exported to run zdb and then imported again. Add a new ztest
function, "-M", to alter ztest behavior to prevent this.
Add new tests to verify the new functionality. Tests provided by
Giuseppe Di Natale.
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Ned Bass <bass6@llnl.gov>
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#745Closes#6279
Currently, there is no way to pause a scrub. Pausing may
be useful when the pool is busy with other I/O to preserve
bandwidth.
This patch adds the ability to pause and resume scrubbing.
This is achieved by maintaining a persistent on-disk scrub state.
While the state is 'paused' we do not scrub any more blocks.
We do however perform regular scan housekeeping such as
freeing async destroyed and deadlist blocks while paused.
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Thomas Caputi <tcaputi@datto.com>
Reviewed-by: Serapheim Dimitropoulos <serapheimd@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alek Pinchuk <apinchuk@datto.com>
Closes#6167
This prints dashes instead of zeros for zero latency values in
'zpool iostat -p'. You'll get zero latencies reported when the
disk is idle, but technically a zero latency is invalid, since you
can't measure the latency of doing nothing.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#6210
Allow new members to be added to a pool mixing raidz and mirror vdevs
without giving -f, as long as they have matching redundancy. This case
was missed in #5915, which only handled zpool create.
Add zfstest zpool_add_010_pos.ksh, with test of zpool create
followed by zpool add of mixed raidz and mirror vdevs.
Add some more mixed raidz and mirror cases to zpool_create_006_pos.ksh.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Haakan Johansson <f96hajo@chalmers.se>
Issue #5915Closes#6181
Users can now provide their own scripts to be run
with 'zpool iostat/status -c'. User scripts should be
placed in ~/.zpool.d to be included in zpool's
default search path.
Provide a script which can be used with
'zpool iostat|status -c' that will return the type of
device (hdd, sdd, file).
Provide a script to get various values from smartctl
when using 'zpool iostat/status -c'.
Allow users to define the ZPOOL_SCRIPTS_PATH
environment variable which can be used to override
the default 'zpool iostat/status -c' search path.
Allow the ZPOOL_SCRIPTS_ENABLED environment
variable to enable or disable 'zpool status/iostat -c'
functionality.
Use the new smart script to provide the serial command.
Install /etc/sudoers.d/zfs file which contains the sudoer
rule for smartctl as a sample.
Allow 'zpool iostat/status -c' tests to run in tree.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#6121Closes#6153
This addition will enable us to sync an open TXG to the main pool
on demand. The functionality is similar to 'sync(2)' but 'zpool sync'
will return when data has hit the main storage instead of potentially
just the ZIL as is the case with the 'sync(2)' cmd.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Alek Pinchuk <apinchuk@datto.com>
Closes#6122
This patch adds a '-f' option to 'zpool offline' to fault a vdev
instead of bringing it offline. Unlike the OFFLINE state, the
FAULTED state will trigger the FMA code, allowing for things like
autoreplace and triggering the slot fault LED. The -f faults
persist across imports, unless they were set with the temporary
(-t) flag. Both persistent and temporary faults can be cleared
with zpool clear.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#6094
Enable additional test cases, in most cases this required a few
minor modifications to the test scripts. In a few cases a real
bug was uncovered and fixed. And in a handful of cases where pools
are layered on pools the test case will be skipped until this is
supported. Details below for each test case.
* zpool_add_004_pos - Skip test on Linux until adding zvols to pools
is fully supported and deadlock free.
* zpool_add_005_pos.ksh - Skip dumpadm portion of the test which isn't
relevant for Linux. The find_vfstab_dev, find_mnttab_dev, and
save_dump_dev functions were updated accordingly for Linux. Add
O_EXCL to the in-use check to prevent the -f (force) option from
working for mounted filesystems and improve the resulting error.
* zpool_add_006_pos - Update test case such that it doesn't depend
on nested pools. Switch to truncate from mkfile to reduce space
requirements and speed up the test case.
* zpool_clear_001_pos - Speed up test case by filling filesystem to
25% capacity.
* zpool_create_002_pos, zpool_create_004_pos - Use sparse files for
file vdevs in order to avoid increasing the partition size.
* zpool_create_006_pos - 6ba1ce9 allows raidz+mirror configs with
similar redundancy. Updating the valid_args and forced_args cases.
* zpool_create_008_pos - Disable overlapping partition portion.
* zpool_create_011_neg - Fix to correctly create the extra partition.
Modified zpool_vdev.c to use fstat64_blk() wrapper which includes
the st_size even for block devices.
* zpool_create_012_neg - Updated to properly find swap devices.
* zpool_create_014_neg, zpool_create_015_neg - Updated to use
swap_setup() and swap_cleanup() wrappers which do the right thing
on Linux and Illumos. Removed '-n' option which succeeds under
Linux due to differences in the in-use checks.
* zpool_create_016_pos.ksh - Skipped test case isn't useful.
* zpool_create_020_pos - Added missing / to cleanup() function.
Remove cache file prior to test to ensure a clean environment
and avoid false positives.
* zpool_destroy_001_pos - Removed test case which creates a pool on
a zvol. This is more likely to deadlock under Linux and has never
been completely supported on any platform.
* zpool_destroy_002_pos - 'zpool destroy -f' is unsupported on Linux.
Mount point must not be busy in order to unmount them.
* zfs_destroy_001_pos - Handle EBUSY error which can occur with
volumes when racing with udev.
* zpool_expand_001_pos, zpool_expand_003_neg - Skip test on Linux
until adding zvols to pools is fully supported and deadlock free.
The test could be modified to use loop-back devices but it would
be preferable to use the test case as is for improved coverage.
* zpool_export_004_pos - Updated test case to such that it doesn't
depend on nested pools. Normal file vdev under /var/tmp are fine.
* zpool_import_all_001_pos - Updated to skip partition 1, which is
known as slice 2, on Illumos. This prevents overwriting the
default TESTPOOL which was causing the failure.
* zpool_import_002_pos, zpool_import_012_pos - No changes needed.
* zpool_remove_003_pos - No changes needed
* zpool_upgrade_002_pos, zpool_upgrade_004_pos - Root cause addressed
by upstream OpenZFS commit 3b7f360.
* zpool_upgrade_007_pos - Disabled in test case due to known failure.
Opened issue https://github.com/zfsonlinux/zfs/issues/6112
* zvol_misc_002_pos - Updated to to use ext2.
* zvol_misc_001_neg, zvol_misc_003_neg, zvol_misc_004_pos,
zvol_misc_005_neg, zvol_misc_006_pos - Moved to skip list, these
test case could be updated to use Linux's crash dump facility.
* zvol_swap_* - Updated to use swap_setup/swap_cleanup helpers.
File creation switched from /tmp to /var/tmp. Enabled minimal
useful tests for Linux, skip test cases which aren't applicable.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #3484
Issue #5634
Issue #2437
Issue #5202
Issue #4034Closes#6095
CID 161638: Resource leak (RESOURCE_LEAK)
Ensure the string array in print_zpool_script_help
is freed in cases when there is an error.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#6111
This commit allow higher ashift values (up to 16) in 'zpool create'
The ashift value was previously limited to 13 (8K block) in b41c990
because the limited number of uberblocks we could fit in the
statically sized (128K) vdev label ring buffer could prevent the
ability the safely roll back a pool to recover it.
Since b02fe35 the largest uberblock size we support is 8K: this
allow us to store a minimum number of 16 uberblocks in the vdev
label, even with higher ashift values.
Additionally change 'ashift' pool property behaviour: if set it will
be used as the default hint value in subsequent vdev operations
('zpool add', 'attach' and 'replace'). A custom ashift value can still
be specified from the command line, if desired.
Finally, fix a bug in add-o_ashift.ksh caused by a missing variable.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#2024Closes#4205Closes#4740Closes#5763
* Add zfs_nicebytes() to print human-readable sizes
Some 'zfs', 'zpool' and 'zdb' output strings can be confusing to the
user when no units are specified. This add a new zfs_nicenum_format
"ZFS_NICENUM_BYTES" used to print bytes in their human-readable form.
Additionally, update some test cases to use machine-parsable 'zfs get'.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#2414Closes#3185Closes#3594Closes#6032
This patch updates the "zpool status/iostat -c" commands to only run
"pre-baked" scripts from the /etc/zfs/zpool.d directory (or wherever
you install to). The scripts can only be run from -c as an unprivileged
user (unless the ZPOOL_SCRIPTS_AS_ROOT environment var is
set by root). This was done to encourage scripts to be written is such
a way that normal users can use them, and to be cautious. If your
script needs to run a privileged command, consider adding the
appropriate line in /etc/sudoers. See zpool(8) for an example of how
to do this.
The patch also allows the scripts to output custom column names. If
the script outputs a line like:
name=value
then "name" is used for the column name, and "value" is its value.
Multiple columns can be specified by outputting multiple lines. Column
names and values can have spaces. If the value is empty, a dash (-) is
printed instead.
After all the "name=value" lines are read (if any), zpool will take the
next the next line of output (if any) and print it without a column
header. After that, no more lines will be processed. This can be
useful for printing errors.
Lastly, this patch also disables the -c option with the latency and
request size histograms, since it produced awkward output and made the
code harder to maintain.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#5852
Be sure to invalidate a vdev's cache before performing
a zpool labelclear. There are cases where the cache is
stale because we did some operation that bypassed it,
and since we are doing an open with only O_RDWR, we
should invalidate it to be safe.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#6009
Authored by: Yuri Pankov <yuri.pankov@nexenta.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Porting Notes:
- Updated 'zpool labelclear' and 'zdb -l' such that they attempt
to find a vdev given solely its short name. This behavior is
consistent with the upstream OpenZFS code and the test cases
depend on it. The actual implementation differs slightly due
to device naming conventions on Linux.
- auto_online_001_pos, auto_replace_001_pos and add-o_ashift
test cases updated to expect failure when no label exists.
- read_efi_label() and zpool_label_disk_check() are read-only
operations and should use O_RDONLY at open time to enforce this.
- zpool_label_disk() and zpool_relabel_disk() write the partition
information using O_DIRECT an fsync() and page cache invalidation
to ensure a consistent view of the device.
- dump_label() in zdb should invalidate the page cache in order
to get the authoritative label from disk.
OpenZFS-issue: https://www.illumos.org/issues/6865
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/c95076cCloses#5981
Allow a pool to be created with both raidz and mirror members,
without giving -f, as long as they have matching redundancy.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Haakan T Johansson <f96hajo@chalmers.se>
Closes#5915
df83110 added the ability to specify a custom "ashift" value from the command
line in 'zpool add' and 'zpool attach'. This commit adds additional checks to
the provided ashift to prevent invalid values from being used, which could
result in disastrous consequences for the whole pool.
Additionally provide ASHIFT_MAX and ASHIFT_MIN definitions in spa.h.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#5878
When a pool is suspended it's impossible to read the list
of damaged files from disk. This would result in a generic
misleading "insufficient permissions" error message.
Update zpool_get_errlog() to use the standard zpool error
logging functions to generate a useful error message. In
this case:
errors: List of errors unavailable: pool I/O is currently suspended
This patch does not address the related issue of potentially
not being able to resume a suspend pool when the underlying
device names have changed.
Additionally, remove the error handling from zfs_alloc()
in zpool_get_errlog() for readability since this function
can never fail.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4031Closes#5731Closes#5907
- Pass $VDEV_ENC_SYSFS_PATH to 'zpool [iostat|status] -c' to include
enclosure LED sysfs path.
- Set LEDs correctly after import. This includes clearing any erroniously
set LEDs prior to the import, and setting the LED for any UNAVAIL drives.
- Include symlink for vdev_attach-led.sh in Makefile.am.
- Print the VDEV path in all-syslog.sh, and fix it so the pool GUID actually
prints.
Reviewed-by: Don Brady <don.brady@intel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#5716Closes#5751
Porting notes:
- Many changes were already made in ZoL (for ex. in d4ed66734).
Authored by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: Yuri Pankov <yuri.pankov@nexenta.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: George Melikov <mail@gmelikov.ru>
OpenZFS-issue: https://www.illumos.org/issues/6872
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/f83b46bCloses#5640
Porting Notes:
- Many of the fixes proposed by this patch were already applied.
In the cases where a different but equivalent fix was made the
code was updated with the OpenZFS version to minimize differences.
- The zpool_get_vdev_by_name() function was previously removed
by commit 235db0a.
Authored by: Igor Kozhukhov <ikozhukhov@gmail.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Andy Stormont <astormont@racktopsystems.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Haakan T Johansson <f96hajo@chalmers.se>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/6551
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/b327cd3Closes#5590
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Haakan T Johansson <f96hajo@chalmers.se>
Closes#5547Closes#5543
zpool iostat allows you to specify only certain vdevs to display.
Currently, if you run 'zpool iostat -c CMD vdev1 vdev2 ...'
on specific vdevs, it will actually run the command on *all* vdevs,
and just display the results for the vdevs you specify. This patch
corrects the behavior to only run the command on the specified vdevs,
and also enables the zpool_iostat_005_pos.ksh tests.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#5443
Enable picky cstyle checks and resolve the new warnings. The vast
majority of the changes needed were to handle minor issues with
whitespace formatting. This patch contains no functional changes.
Non-whitespace changes are as follows:
* 8 times ; to { } in for/while loop
* fix missing ; in cmd/zed/agents/zfs_diagnosis.c
* comment (confim -> confirm)
* change endline , to ; in cmd/zpool/zpool_main.c
* a number of /* BEGIN CSTYLED */ /* END CSTYLED */ blocks
* /* CSTYLED */ markers
* change == 0 to !
* ulong to unsigned long in module/zfs/dsl_scan.c
* rearrangement of module_param lines in module/zfs/metaslab.c
* add { } block around statement after for_each_online_node
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Håkan Johansson <f96hajo@chalmers.se>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#5465
Do not force VDEV_NAME_TYPE_ID in max_width(), instead add it
in the relevant calls to max_width().
The first location of max_width() where VDEV_NAME_TYPE_ID is
now added in show_import() is followed by print_import_config() and
print_logs(). Both these print children vdev names that have been
retrieved using an explicit VDEV_NAME_TYPE_ID added.
The second location is in status_callback(). This is followed by
print_status_config(), print_logs(), print_l2cache(), and
print_spares(). For l2cache and spares it should not matter as there
are no mirror-X or raidz-X involved. print_status_config() as above
retrieves the name using explicit VDEV_NAME_TYPE_ID before
calling itself to print children.
The call of max_width() in get_namewidth() is not changed, as this is
used by zpool_do_iostat(), followed by print_iostat(), which does not
add VDEV_NAME_TYPE_ID.
Overall, we should consider adding VDEV_NAME_TYPE_ID to the
relevant name_flags / cb_name_flags fields, and remove the explicit
adding in called routines.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Haakan T Johansson <f96hajo@chalmers.se>
Closes#5401
This patch adds a command (-c) option to zpool status and zpool iostat. The
-c option allows you to run an arbitrary command on each vdev and display
the first line of output in zpool status/iostat. The environment vars
VDEV_PATH and VDEV_UPATH are set to the vdev's path and "underlying path"
before running the command. For device mapper, multipath, or partitioned
vdevs, VDEV_UPATH is the actual underlying /dev/sd* disk. This can be useful
if the command you're running requires a /dev/sd* device.
The patch also uses /sys/block/<dev>/slaves/ to lookup the underlying device
instead of using libdevmapper. This not only removes the libdevmapper
requirement at build time, but also allows you to resolve device mapper
devices without being root. This means that UDEV_UPATH get set correctly
when running zpool status/iostat as an unprivileged user.
Example:
$ zpool status -c 'echo I am $VDEV_PATH, $VDEV_UPATH'
NAME STATE READ WRITE CKSUM
mypool ONLINE 0 0 0
mirror-0 ONLINE 0 0 0
mpatha ONLINE 0 0 0 I am /dev/mapper/mpatha, /dev/sdc
sdb ONLINE 0 0 0 I am /dev/sdb1, /dev/sdb
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#5368
Sometimes it is desirable to specifically disable one or several
features directly on the 'zpool create' command line.
$ zpool create -o feature@<feature>=disabled ...
Original-patch-by: Turbo Fredriksson <turbo@bayour.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#3460Closes#5142Closes#5324
First rename spare_cbdata_t cb -> spare_cb in print_status_config(),
to free up cb.
Using the structure removes the explicit parameters namewidth
and name_flags from several functions. Also use status_cbdata_t
for print_import_config(). This simplifies print_logs().
Remove the parameter 'verbose' for print_logs(). It does not really
mean verbose, it selected between the print_status_config and
print_import_config() paths. This selection is now done by
cb_print_config of spare_cbdata_t.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Håkan Johansson <f96hajo@chalmers.se>
Closes#5259
When array is passed as a parameter it degenerates into a
pointer so the sizeof(path) in is_shorthand_path() and always
get return value of 8, instead of the string length we want.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: GeLiXin <ge.lixin@zte.com.cn>
Closes#5198
1.coverity scan CID:147445 function zfs_do_send in zfs_main.c
Buffer not null terminated (BUFFER_SIZE_WARNING)
2.coverity scan CID:147443 function zfs_do_bookmark in zfs_main.c
Buffer not null terminated (BUFFER_SIZE_WARNING)
3.coverity scan CID:147660 function main in zinject.c
Passing string argv[0] of unknown size to strcpy
By the way, the leak of g_zfs is fixed.
4.coverity scan CID: 147442 function make_disks in zpool_vdev.c
Buffer not null terminated (BUFFER_SIZE_WARNING)
5.coverity scan CID: 147661 function main in dir_rd_update.c
passing string cp1 of unknown size to strcpy
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: luozhengzheng <luo.zhengzheng@zte.com.cn>
Closes#5130
This first phase brings over the ZFS SLM module, zfs_mod.c, to handle
auto operations in response to disk events. Disk event monitoring is
provided from libudev and generates the expected payload schema for
zfs_mod. This work leverages the recently added devid and phys_path
strings in the vdev label.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@intel.com>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#4673
Commit 519129f added support to multi-thread 'zpool import' for
the case where block devices are scanned for under /dev/. This
commit generalizes that logic and applies it to the case where
device names are acquired from libblkid.
The zpool_find_import_scan() and zpool_find_import_blkid()
functions create an AVL tree containing each device name. Each
entry in this tree is dispatched to a taskq where the function
zpool_open_func() validates the device by opening it and reading
the label. This may result in additional entries being added
to the tree and those device paths being verified.
This is largely how the upstream OpenZFS code behaves but due to
significant differences the non-Linux code has been dropped for
readability. Additionally, this code makes use of taskqs and
kmutexs which are normally not available to the command line tools.
Special care has been taken to allow their use in the import
functions.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#4794
ZFS allows for specific permissions to be delegated to normal users
with the `zfs allow` and `zfs unallow` commands. In addition, non-
privileged users should be able to run all of the following commands:
* zpool [list | iostat | status | get]
* zfs [list | get]
Historically this functionality was not available on Linux. In order
to add it the secpolicy_* functions needed to be implemented and mapped
to the equivalent Linux capability. Only then could the permissions on
the `/dev/zfs` be relaxed and the internal ZFS permission checks used.
Even with this change some limitations remain. Under Linux only the
root user is allowed to modify the namespace (unless it's a private
namespace). This means the mount, mountpoint, canmount, unmount,
and remount delegations cannot be supported with the existing code. It
may be possible to add this functionality in the future.
This functionality was validated with the cli_user and delegation test
cases from the ZFS Test Suite. These tests exhaustively verify each
of the supported permissions which can be delegated and ensures only
an authorized user can perform it.
Two minor bug fixes were required for test-running.py. First, the
Timer() object cannot be safely created in a `try:` block when there
is an unconditional `finally` block which references it. Second,
when running as a normal user also check for scripts using the
both the .ksh and .sh suffixes.
Finally, existing users who are simulating delegations by setting
group permissions on the /dev/zfs device should revert that
customization when updating to a version with this change.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#362Closes#434Closes#4100Closes#4394Closes#4410Closes#4487
