Rob Noris suggested that we could clean up redundant limits for the case
of non-blk mq scenario.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Rob Norris <robn@despairlabs.com>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#16462
In kernels 6.8 and later, the zvol block device is allocated with
qlimits passed during initialization. However, the zvol driver does not
set `max_hw_discard_sectors`, which is necessary to properly
initialize `max_discard_sectors`. This causes the `zvol_misc_trim` test
to fail on 6.8+ kernels when invoking the `blkdiscard` command. Setting
`max_hw_discard_sectors` in the `HAVE_BLK_ALLOC_DISK_2ARG` case resolve
the issue.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Rob Norris <robn@despairlabs.com>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#16462
These had minimal useful information for the admin, didn't work properly
in some places, and knew far too much about taskq internals.
With the new stats available, these should never be needed anymore.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Sponsored-by: Klara, Inc.
Sponsored-by: Syneto
Closes#16171
This adds /proc/spl/kstats/taskq/summary, which attempts to show a
useful subset of stats for all taskqs in the system.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Sponsored-by: Klara, Inc.
Sponsored-by: Syneto
Closes#16171
This exposes a variety of per-taskq stats under /proc/spl/kstat/taskq,
one file per taskq, named for the taskq name.instance.
These include a small amount of info about the taskq config, the current
state of the threads and queues, and various counters for thread and
queue activity since the taskq was created.
To assist with decrementing queue size counters, the list an entry is on
is encoded in spare bits in the entry flags.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Sponsored-by: Klara, Inc.
Sponsored-by: Syneto
Closes#16171
For spl-taskq to use the kstats infrastructure, it has to be available
first.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Sponsored-by: Klara, Inc.
Sponsored-by: Syneto
Closes#16171
Skip ro check for snapshots since they are always ro regardless if ro
flag is passed by mount or not. This allows multi-mounting snapshots
without requiring to specify ro flag.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Chunwei Chen <david.chen@nutanix.com>
Closes#16299
zvol queue limits initialization depends on `zv_volblocksize`, but it is
initialized later, leading to several limits being initialized with
incorrect values, including `max_discard_*` limits. This also causes
`blkdiscard` command to consistently fail, as `blk_ioctl_discard` reads
`bdev_max_discard_sectors()` limits as 0, leading to failure. The fix is
straightforward: initialize `zv->zv_volblocksize` early, before setting
the queue limits. This PR should fix `zvol/zvol_misc/zvol_misc_trim`
failure on recent PRs, as the test case issues `blkdiscard` for a zvol.
Additionally, `zvol_misc_trim` was recently enabled in `6c7d41a`,
which is why the issue wasn't identified earlier.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#16454
zvol_alloc_non_blk_mq()->blk_queue_set_write_cache() needs the disk
queue setup to prevent a NULL pointer deference.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#16453
zpool upgraded with 'feature@project_quota' needs re-layout of SA's
to fix the SA_ZPL_PROJID at SA_PROJID_OFFSET (128). Its necessary for
the correct accounting of object usage against its projid.
Old object (created before upgrade) when gets a projid assigned, its
SA gets re-layout via sa_add_projid(). If object has xattr dir, SA
of xattr dir also gets re-layout. But SA re-layout of xattr objects
inside a xattr dir is not done.
Fix zfs_setattr_dir() to re-layout SA's on xattr objects, when setting
projid on old xattr object (created before upgrade).
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jitendra Patidar <jitendra.patidar@nutanix.com>
Closes#16355Closes#16356
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <robn@despairlabs.com>
Sponsored-by: https://despairlabs.com/sponsor/Closes#16400
Since the change to folios it has just been a wrapper anyway. Linux has
removed their wrapper, so we add one.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <robn@despairlabs.com>
Sponsored-by: https://despairlabs.com/sponsor/Closes#16400
These fields are very old, so no detection necessary; we just move them
into the limit setup functions.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <robn@despairlabs.com>
Sponsored-by: https://despairlabs.com/sponsor/Closes#16400
Apply them with with the rest of the settings.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <robn@despairlabs.com>
Sponsored-by: https://despairlabs.com/sponsor/Closes#16400
Detect it, and use a macro to make sure we always match the prototype.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <robn@despairlabs.com>
Sponsored-by: https://despairlabs.com/sponsor/Closes#16400
In 6.11 struct queue_limits gains a 'features' field, where, among other
things, flush and write-cache are enabled. Detect it and use it.
Along the way, the blk_queue_set_write_cache() compat wrapper gets a
little cleanup. Since both flags are alway set together, its now a
single bool. Also the very very ancient version that sets q->flush_flags
directly couldn't actually turn it off, so I've fixed that. Not that we
use it, but still.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <robn@despairlabs.com>
Sponsored-by: https://despairlabs.com/sponsor/Closes#16400
It gets hairier again in Linux 6.11, so I want some actual theory of
operation laid out for next time.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <robn@despairlabs.com>
Sponsored-by: https://despairlabs.com/sponsor/Closes#16400
This applies the same change in #9115 to FreeBSD. This was actually the
old behavior in FreeBSD 12; it only regressed when FreeBSD support was
added to OpenZFS. As far as I can tell, the timeline went like this:
* Illumos's zfsvfs_teardown used an unconditional txg_wait_synced
* Illumos added the dirty data check [^4]
* FreeBSD merged in Illumos's conditional check [^3]
* OpenZFS forked from Illumos
* OpenZFS removed the dirty data check in #7795 [^5]
* @mattmacy forked the OpenZFS repo and began to add FreeBSD support
* OpenZFS PR #9115[^1] recreated the same dirty data check that Illumos
used, in slightly different form. At this point the OpenZFS repo did
not yet have multi-OS support.
* Matt Macy merged in FreeBSD support in #8987[^2] , but it was based on
slightly outdated OpenZFS code.
In my local testing, this vastly improves the reboot speed of a server
with a large pool that has 1000 datasets and is resilvering an HDD.
[^1]: https://github.com/openzfs/zfs/pull/9115
[^2]: https://github.com/openzfs/zfs/pull/8987
[^3]: 10b9d77bf1
[^4]: 5aaeed5c61
[^5]: https://github.com/openzfs/zfs/pull/7795
Sponsored by: Axcient
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Alan Somers <asomers@gmail.com>
Closes#16268
Previous code evicted nr_to_scan items from each NUMA node. This
not only multiplied the eviction by the number of nodes, but could
exhaust the smaller ones, evicting inodes used by acive workload
and requiring their immediate recreation. This patch spreads the
requested eviction between all NUMA nodes proportionally to their
evictable counts, which should be closer to expected LRU logic.
See kernel's super_cache_scan() as a similar logic example.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ameer Hamza <ahamza@ixsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#16397
ZFS implements copy_file_range(2) using block cloning when possible.
This implementation must respect the RLIMIT_FSIZE limit.
zfs_clone_range() already checks the limit, so it is safe to remove this
check in zfs_freebsd_copy_file_range(). Moreover, the removed check
produces false positives: the length passed to copy_file_range(2) may be
larger than the input file size; as the man page notes, "for best
performance, call copy_file_range() with the largest len value
possible." In particular, some existing code passes SSIZE_MAX there.
The check in zfs_clone_range() clamps the length to the input file's
size before checking, but the removed check uses the caller supplied
length, so something like
$ echo a > /tmp/foo
$ limits -f 1024 cat /tmp/foo > /tmp/bar
fails because FreeBSD's cat(1) uses copy_file_range(2) in the manner
described above.
Reported-by: Philip Paeps <philip@FreeBSD.org>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Currently, if a minor is in use when we try to remove it, we'll skip it
and never come back to it again. Since the zvol state is hung off the
minor in the kernel, this can get us into weird situations if something
tries to use it after the removal fails. It's even worse at pool export,
as there's now a vestigial zvol state with no pool under it. It's
weirder again if the pool is subsequently reimported, as the zvol code
(reasonably) assumes the zvol state has been properly setup, when it's
actually left over from the previous import of the pool.
This commit attempts to tackle that by setting a flag on the zvol if its
minor can't be removed, and then checking that flag when a request is
made and rejecting it, thus stopping new work coming in.
The flag also causes a condvar to be signaled when the last client
finishes. For the case where a single minor is being removed (eg
changing volmode), it will wait for this signal before proceeding.
Meanwhile, when removing all minors, a background task is created for
each minor that couldn't be removed on the spot, and those tasks then
wake and clean up.
Since any new tasks are queued on to the pool's spa_zvol_taskq,
spa_export_common() will continue to wait at export until all minors are
removed.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Sponsored-by: Klara, Inc.
Sponsored-by: Wasabi Technology, Inc.
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Closes#14872Closes#16364
SET_ERROR is our facility for tracking errors internally. The negation
is to match the what the kernel expects from us. Thus, the negation
should happen outside of the SET_ERROR.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Sponsored-by: Klara, Inc.
Sponsored-by: Wasabi Technology, Inc.
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Closes#16364
This includes the last 12.x release (now EOL) and 13.0 development
versions (<1300139).
Sponsored-by: https://despairlabs.com/sponsor/
Signed-off-by: Rob Norris <robn@despairlabs.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Linux provides SLAB_RECLAIM_ACCOUNT and __GFP_RECLAIMABLE flags to
mark memory allocations that can be freed via shinker calls. It
should allow kernel to tune and group such allocations for lower
memory fragmentation and better reclamation under pressure.
This patch marks as reclaimable most of ARC memory, directly
evictable via ZFS shrinker, plus also dnode/znode/sa memory,
indirectly evictable via kernel's superblock shrinker.
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Allan Jude <allan@klarasystems.com>
- When receiving memory pressure signal from OS be more strict
trying to free some memory. Otherwise kernel may come again and
request much more. Return as result how much arc_c was actually
reduced due to this request, that may be less than requested.
- On Linux when receiving direct reclaim from some file system
(that may be ZFS) instead of ignoring request completely, just
shrink the ARC, but do not wait for eviction. Waiting there may
cause deadlock. Ignoring it as before may put extra pressure on
other caches and/or swap, and cause OOM if nothing help. While
not waiting may result in more ARC evicted later, and may be too
late if OOM killer activate right now, but I hope it to be better
than doing nothing at all.
- On Linux set arc_no_grow before waiting for reclaim, not after,
or it may grow back while we are waiting.
- On Linux add new parameter zfs_arc_shrinker_seeks to balance
ARC eviction cost, relative to page cache and other subsystems.
- Slightly update Linux arc_set_sys_free() math for new kernels.
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Reviewed-by: Rob Norris <rob.norris@klarasystems.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Changed zfs_k(un)map_atomic to zfs_k(un)map_local
Signed-off-by: Jason Lee <jasonlee@lanl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
This helper was introduced long ago, in 5.16. Since 6.10, bd_inode no
longer exists, but the helper has been updated, so detect it and use it
in all versions where it is available.
Signed-off-by: Rob Norris <robn@despairlabs.com>
Sponsored-by: https://despairlabs.com/sponsor/
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Linux 6.10 change kmem_cache_alloc to be a macro, rather than a
function, such that the old #undef for it in spl-kmem-cache.c would
remove its definition completely, breaking the build.
This inverts the model used before. Rather than always defining the
kmem_cache_* macro, then undefining then inside spl-kmem-cache.c,
instead we make a special tag to indicate we're currently inside
spl-kmem-cache.c, and not defining those in macros in the first place,
so we can use the kernel-supplied kmem_cache_* functions to implement
spl_kmem_cache_*, as we expect.
For all other callers, we create the macros as normal and remove access
to the kernel's own conflicting names.
Signed-off-by: Rob Norris <robn@despairlabs.com>
Sponsored-by: https://despairlabs.com/sponsor/
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Linux has started moving to a model where instead of applying block
queue limits through individual modification functions, a complete
limits structure is built up and applied atomically, either when the
block device or open, or some time afterwards. As of 6.10 this
transition appears only partly completed.
This commit matches that model within OpenZFS in a way that should work
for past and future kernels. We set up a queue limits structure with any
limits that have had their modification functions removed. For newer
kernels that can have limits applied at block device open
(HAVE_BLK_ALLOC_DISK_2ARG), we have a conversion function to turn the
OpenZFS queue limits structure into Linux's queue_limits structure,
which can then be passed in. For older kernels, we provide an
application function that just calls the old functions for each limit in
the structure.
Signed-off-by: Rob Norris <robn@despairlabs.com>
Sponsored-by: https://despairlabs.com/sponsor/
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
This freeuio() interface was introduced to FreeBSD recently. For now
it simply calls free(), so this change has no effect. However, this
may not always be true, and in CheriBSD this change is required.
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brooks Davis <brooks.davis@sri.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
In several functions, we use a flag variable to track whether
zv_suspend_lock is held. This flag was not getting reset in a
particular case where we need to retry the underlying operation,
resulting in a lock leak. Make sure to update the flag where necessary.
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
The 6.9 kernel behaves differently in how it releases block devices. In
the common case it will async release the device only after the return
to userspace. This is different from the 6.8 and older kernels which
release the block devices synchronously. To get around this, call
add_disk() from a workqueue so that the kernel uses a different
codepath to release our zvols in the way we expect. This stops
zfs_allow_010_pos from hanging.
Fixes: #16089
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Rob Norris <rob.norris@klarasystems.com>
Otherwise if zfs is unloaded and reroot is being used it trips over a
stale pointer.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: Rubicon Communications, LLC ("Netgate")
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#16242
Recent UMA changes repurposed the use of UMA_MD_SMALL_ALLOC in a way
that breaks arc_available_memory on -CURRENT. This change
ensures that arc_available_memory uses the new symbol
while maintaining compatibility with older FreeBSD releases.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Bojan Novković <bnovkov@FreeBSD.org>
Closes#16230
These members have directly references to the global variables
exposed by the kernel. They are not going to be changed by this
kernel module.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Zhenlei Huang <zlei@FreeBSD.org>
Closes#16210
We always call it twice with JUSTLOOKING and then FORREAL.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Pawel Jakub Dawidek <pawel@dawidek.net>
Closes#16225
Originally Solaris didn't expect errors there, but they may happen
if we fail to add entry into ZAP. Linux fixed it in #7421, but it
was never fully ported to FreeBSD.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#13215Closes#16138
And, make the output fd an arg to zfs_dbgmsg_print(). This is a change
in behaviour, but keeps it consistent with where crash traces go, and
it's easy to argue this is what we want anyway; this is information
about the task, not the actual output of the task.
Sponsored-by: Klara, Inc.
Sponsored-by: Wasabi Technology, Inc.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Closes#16181
FreeBSD was using fprintf(), which might not be signal-safe. Meanwhile,
Linux's locking did not cover the header output. This two quirks are
unrelated, but both have the same response: be like the other one. So
with this commit, both functions are the same except for the names of
their lock and list variables.
Sponsored-by: Klara, Inc.
Sponsored-by: Wasabi Technology, Inc.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Closes#16181
When running a debug kernel with lockdep enabled there
are several locks which report false positives. Set
MUTEX_NOLOCKDEP/RW_NOLOCKDEP to disable these warnings.
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#16188
In P2ALIGN, the result would be incorrect when align is unsigned
integer and x is larger than max value of the type of align.
In that case, -(align) would be a positive integer, which means
high bits would be zero and finally stay zero after '&' when
align is converted to a larger integer type.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Youzhong Yang <yyang@mathworks.com>
Signed-off-by: Qiuhao Chen <chenqiuhao1997@gmail.com>
Closes#15940
This commit replaces current usages of schedule_timeout() with
schedule_timeout_interruptible() in code paths that expect the running
task to sleep for a short period of time. When schedule_timeout() is
called without previously calling set_current_state(), the running
task never sleeps because the task state remains in TASK_RUNNING.
By calling schedule_timeout_interruptible() to set the task state to
TASK_INTERRUPTIBLE before calling schedule_timeout() we achieve the
intended/desired behavior of putting the task to sleep for the
specified timeout.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Daniel Perry <dtperry@amazon.com>
Closes#16150
If the underlying device doesn't have a write-back cache, the kernel
will just return a successful response. This doesn't hurt anything, but
it's extra work on the IO taskqs that are unnecessary. So, detect this
when we open the device for the first time.
Sponsored-by: Klara, Inc.
Sponsored-by: Wasabi Technology, Inc.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Closes#16148
When renaming a zvol, insert it into zvol_htable using the new name, not
the old name. Otherwise some operations won't work. For example,
"zfs set volsize" while the zvol is open.
Sponsored by: Axcient
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alek Pinchuk <apinchuk@axcient.com>
Signed-off-by: Alan Somers <asomers@FreeBSD.org>
Closes#16127Closes#16128
Previously, abd_iter_page() would assume that every scatterlist would
contain a single page (compound or no), because that's all we ever
create in abd_alloc_chunks(). However, scatterlists can contain multiple
pages of arbitrary provenance, and if we get one of those, we'd get all
the math wrong.
This reworks things to handle multiple pages in a scatterlist, by
properly finding the right page within it for the given offset, and
understanding better where the end of the page is and not crossing it.
Sponsored-by: Klara, Inc.
Sponsored-by: Wasabi Technology, Inc.
Reported-by: Brian Atkinson <batkinson@lanl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Closes#16108
The only possible ioctl is a flush, and any other kind of meta-operation
introduced in the future is likely to have different semantics (much
like trim did). So, lets just call it what it is.
Sponsored-by: Klara, Inc.
Sponsored-by: Wasabi Technology, Inc.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Closes#16064
There's no other options, so we can just always assume its a flush.
Includes some light refactoring where a switch statement was doing
control flow that no longer works.
Sponsored-by: Klara, Inc.
Sponsored-by: Wasabi Technology, Inc.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Closes#16064
If a linear buffer spans multiple pages, and the first page has a
non-zero starting offset, the checker would not include the offset, and
so would think there was an alignment gap at the end of the first page,
rather than at the start.
That is, for a 16K buffer spread across five pages with an initial 512B
offset:
[.XXXXXXX][XXXXXXXX][XXXXXXXX][XXXXXXXX][XXXXXXX.]
It would be interpreted as:
[XXXXXXX.][XXXXXXXX]...
And be rejected as misaligned.
Since it's already a linear ABD, the "linearising" copy would just reuse
the buffer as-is, and the second check would failing, tripping the
VERIFY in vdev_disk_io_rw().
This commit fixes all this by including the offset in the check for
end-of-page alignment.
Sponsored-by: Klara, Inc.
Sponsored-by: Wasabi Technology, Inc.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Closes#16076
