Adding O_DIRECT support to ZFS to bypass the ARC for writes/reads.
O_DIRECT support in ZFS will always ensure there is coherency between
buffered and O_DIRECT IO requests. This ensures that all IO requests,
whether buffered or direct, will see the same file contents at all
times. Just as in other FS's , O_DIRECT does not imply O_SYNC. While
data is written directly to VDEV disks, metadata will not be synced
until the associated TXG is synced.
For both O_DIRECT read and write request the offset and request sizes,
at a minimum, must be PAGE_SIZE aligned. In the event they are not,
then EINVAL is returned unless the direct property is set to always (see
below).
For O_DIRECT writes:
The request also must be block aligned (recordsize) or the write
request will take the normal (buffered) write path. In the event that
request is block aligned and a cached copy of the buffer in the ARC,
then it will be discarded from the ARC forcing all further reads to
retrieve the data from disk.
For O_DIRECT reads:
The only alignment restrictions are PAGE_SIZE alignment. In the event
that the requested data is in buffered (in the ARC) it will just be
copied from the ARC into the user buffer.
For both O_DIRECT writes and reads the O_DIRECT flag will be ignored in
the event that file contents are mmap'ed. In this case, all requests
that are at least PAGE_SIZE aligned will just fall back to the buffered
paths. If the request however is not PAGE_SIZE aligned, EINVAL will
be returned as always regardless if the file's contents are mmap'ed.
Since O_DIRECT writes go through the normal ZIO pipeline, the
following operations are supported just as with normal buffered writes:
Checksum
Compression
Encryption
Erasure Coding
There is one caveat for the data integrity of O_DIRECT writes that is
distinct for each of the OS's supported by ZFS.
FreeBSD - FreeBSD is able to place user pages under write protection so
any data in the user buffers and written directly down to the
VDEV disks is guaranteed to not change. There is no concern
with data integrity and O_DIRECT writes.
Linux - Linux is not able to place anonymous user pages under write
protection. Because of this, if the user decides to manipulate
the page contents while the write operation is occurring, data
integrity can not be guaranteed. However, there is a module
parameter `zfs_vdev_direct_write_verify` that controls the
if a O_DIRECT writes that can occur to a top-level VDEV before
a checksum verify is run before the contents of the I/O buffer
are committed to disk. In the event of a checksum verification
failure the write will return EIO. The number of O_DIRECT write
checksum verification errors can be observed by doing
`zpool status -d`, which will list all verification errors that
have occurred on a top-level VDEV. Along with `zpool status`, a
ZED event will be issues as `dio_verify` when a checksum
verification error occurs.
ZVOLs and dedup is not currently supported with Direct I/O.
A new dataset property `direct` has been added with the following 3
allowable values:
disabled - Accepts O_DIRECT flag, but silently ignores it and treats
the request as a buffered IO request.
standard - Follows the alignment restrictions outlined above for
write/read IO requests when the O_DIRECT flag is used.
always - Treats every write/read IO request as though it passed
O_DIRECT and will do O_DIRECT if the alignment restrictions
are met otherwise will redirect through the ARC. This
property will not allow a request to fail.
There is also a module parameter zfs_dio_enabled that can be used to
force all reads and writes through the ARC. By setting this module
parameter to 0, it mimics as if the direct dataset property is set to
disabled.
Reviewed-by: Brian Behlendorf <behlendorf@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Atkinson <batkinson@lanl.gov>
Co-authored-by: Mark Maybee <mark.maybee@delphix.com>
Co-authored-by: Matt Macy <mmacy@FreeBSD.org>
Co-authored-by: Brian Behlendorf <behlendorf@llnl.gov>
Closes#10018
Removing the platform #ifdefs from shared headers in favour of
per-platform headers. Makes abd_t much leaner, among other things.
Sponsored-by: Klara, Inc.
Sponsored-by: Wasabi Technology, Inc.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Closes#16253
On fedora 40, on the 6.9.4 kernel (in updates-testing), assign_str
expands to a "do {<stuff> } while(0)" loop. Without this semicolon,
the while(0) is unterminated, causing a cascade of useless errors.
With this semicolon, it compiles fine. It also compiles fine on 6.8.11
(the previous kernel). I have not tested earlier kernels than that, but
at worst it should add a pointless semicolon.
All other instances in the source tree are already terminated with
semicolons.
Signed-off-by: Daniel Berlin <dberlin@dberlin.org>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
There's no other options, so we can just always assume its a flush.
Includes some light refactoring where a switch statement was doing
control flow that no longer works.
Sponsored-by: Klara, Inc.
Sponsored-by: Wasabi Technology, Inc.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Closes#16064
On Linux the ioctl_ficlonerange() and ioctl_ficlone() system calls
are expected to either fully clone the specified range or return an
error. The range may be for an entire file. While internally ZFS
supports cloning partial ranges there's no way to return the length
cloned to the caller so we need to make this all or nothing.
As part of this change support for the REMAP_FILE_CAN_SHORTEN flag
has been added. When REMAP_FILE_CAN_SHORTEN is set zfs_clone_range()
will return a shortened range when encountering pending dirty records.
When it's clear zfs_clone_range() will block and wait for the records
to be written out allowing the blocks to be cloned.
Furthermore, the file range lock is held over the region being cloned
to prevent it from being modified while cloning. This doesn't quite
provide an atomic semantics since if an error is encountered only a
portion of the range may be cloned. This will be converted to an
error if REMAP_FILE_CAN_SHORTEN was not provided and returned to the
caller. However, the destination file range is left in an undefined
state.
A test case has been added which exercises this functionality by
verifying that `cp --reflink=never|auto|always` works correctly.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#15728Closes#15842
While picking parts from #14909 I've missed Linux tracing specific
ones, that went unnoticed in default configurations, but breaks the
build in some.
Reviewed-by: Ameer Hamza <ahamza@ixsystems.com>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#15730
6.6 made i_ctime inaccessible; 6.7 has done the same for i_atime and
i_mtime. This extends the method used for ctime in b37f29341 to atime
and mtime as well.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <robn@despairlabs.com>
Sponsored-by: https://github.com/sponsors/robnCloses#15681
Copy the disable parameter that FreeBSD implemented, and extend it to
work on Linux as well, until we're sure this is stable.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#15529
There is no sense to have separate implementations for FreeBSD and
Linux. Make Linux code shared as more functional and just register
FreeBSD-specific prune callback with arc_add_prune_callback() API.
Aside of code cleanup this should fix excessive pruning on FreeBSD:
https://bugs.freebsd.org/bugzilla/show_bug.cgi?id=274698
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mark Johnston <markj@FreeBSD.org>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#15456
In most cases we do not care about exact number of buffers linked
to the header, we just need to know if it is zero, non-zero or one.
That can easily be checked just looking on b_buf pointer or in some
cases derefencing it.
b_ebufcnt is read only once, and in that case we already traverse
the list as part of arc_buf_remove(), so second traverse should not
be expensive.
This reduces L1 ARC header size by 8 bytes and full crypto header by
16 bytes, down to 176 and 232 bytes on FreeBSD respectively.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#15350
In dnode_destroy, dn_objset is invalidated. However, it will later call
into dbuf_destroy, in which DTRACE_SET_STATE will try to access spa_name
via dn_objset causing illegal pointer access.
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chunwei Chen <david.chen@nutanix.com>
Closes#15333
In commit 0d72b92883c651a11059d93335f33d65c6eb653b, a new u32 argument
for the request_mask was added to generic_fillattr. This is the same
request_mask for statx that's present in the most recent API implemented
by zpl_getattr_impl. This commit conditionally adds it to the
zpl_generic_fillattr(...) macro, as well as the zfs_getattr_fast(...)
implementation, when configure determines it's present in the kernel's
generic_fillattr(...).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#15263
In Linux commit 13bc24457850583a2e7203ded05b7209ab4bc5ef, direct access
to the i_ctime member of struct inode was removed. The new approach is
to use accessor methods that exclusively handle passing the timestamp
around by value. This change adds new tests for each of these functions
and introduces zpl_* equivalents in include/os/linux/zfs/sys/zpl.h. In
where the inode_get/set_ctime*() functions exist, these zpl_* calls will
be mapped to the new functions. On older kernels, these macros just wrap
direct-access calls. The code that operated on an address of ip->i_ctime
to call ZFS_TIME_DECODE() now will take a local copy using
zpl_inode_get_ctime(), and then pass the address of the local copy when
performing the ZFS_TIME_DECODE() call, in all cases, rather than
directly accessing the member.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#15263Closes#15257
Added in ab26409db7 ("Linux 3.1 compat, super_block->s_shrink"), with
the only consumer which needed the count getting retired in 066e825221
("Linux compat: Minimum kernel version 3.10").
The counter gets in the way of not maintaining the list to begin with.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#15274
Redhat have backported copy_file_range and clone_file_range to the EL7
kernel using an "extended file operations" wrapper structure. This
connects all that up to let cloning work there too.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Kay Pedersen <mail@mkwg.de>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Sponsored-By: OpenDrives Inc.
Sponsored-By: Klara Inc.
Closes#15050
Prior to Linux 4.5, the FICLONE etc ioctls were specific to BTRFS, and
were implemented as regular filesystem-specific ioctls. This implements
those ioctls directly in OpenZFS, allowing cloning to work on older
kernels.
There's no need to gate these behind version checks; on later kernels
Linux will simply never deliver these ioctls, instead calling the
approprate VFS op.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Kay Pedersen <mail@mkwg.de>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Sponsored-By: OpenDrives Inc.
Sponsored-By: Klara Inc.
Closes#15050
This implements the Linux VFS ops required to service the file
copy/clone APIs:
.copy_file_range (4.5+)
.clone_file_range (4.5-4.19)
.dedupe_file_range (4.5-4.19)
.remap_file_range (4.20+)
Note that dedupe_file_range() and remap_file_range(REMAP_FILE_DEDUP) are
hooked up here, but are not implemented yet.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Kay Pedersen <mail@mkwg.de>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Sponsored-By: OpenDrives Inc.
Sponsored-By: Klara Inc.
Closes#15050
In addition to a number of actual log bytes written, account also a
total written bytes including padding and total allocated bytes (bytes
<= write <= alloc). It should allow to monitor zil traffic and space
efficiency.
Add dtrace probe for zil block size selection.
Make zilstat report more information and fit it into less width.
Reviewed-by: Ameer Hamza <ahamza@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14863
Clang specific pragmas need to be wrapped to prevent a build
warning when compiling with gcc.
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#14814
Clang points out that there is a comparison against -1, but we cannot
fix it because that is from the kernel headers, which we must support.
We can workaround this by using a pragma.
Sponsored-By: Wasabi Technology, Inc.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Youzhong Yang <yyang@mathworks.com>
Signed-off-by: Richard Yao <richard.yao@klarasystems.com>
Closes#14738
Linux kernel 6.3 changed a bunch of APIs to use the dedicated idmap
type for mounts (struct mnt_idmap), we need to detect these changes
and make zfs work with the new APIs.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Youzhong Yang <yyang@mathworks.com>
Closes#14682
Block Cloning allows to manually clone a file (or a subset of its
blocks) into another (or the same) file by just creating additional
references to the data blocks without copying the data itself.
Those references are kept in the Block Reference Tables (BRTs).
The whole design of block cloning is documented in module/zfs/brt.c.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Christian Schwarz <christian.schwarz@nutanix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Rich Ercolani <rincebrain@gmail.com>
Signed-off-by: Pawel Jakub Dawidek <pawel@dawidek.net>
Closes#13392
We had three sha2.h headers in different places.
The FreeBSD version, the Linux version and the generic solaris version.
The only assembly used for acceleration was some old x86-64 openssl
implementation for sha256 within the icp module.
For FreeBSD the whole SHA2 files of FreeBSD were copied into OpenZFS,
these files got removed also.
Tested-by: Rich Ercolani <rincebrain@gmail.com>
Tested-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tino Reichardt <milky-zfs@mcmilk.de>
Closes#13741
When a page is faulted in for memory mapped I/O the page lock
may be dropped before it has been read and marked up to date.
If a buffered read encounters such a page in mappedread() it
must wait until the page has been updated. Failure to do so
will result in a panic on debug builds and incorrect data on
production builds.
The critical part of this change is in mappedread() where pages
which are not up to date are now handled. Additionally, it
includes the following simplifications.
- zfs_getpage() and zfs_fillpage() could be passed an array of
pages. This could be more efficient if it was used but in
practice only a single page was ever provided. These
interfaces were simplified to acknowledge that.
- update_pages() was modified to correctly set the PG_error bit
on a page when it cannot be read by dmu_read().
- Setting PG_error and PG_uptodate was moved to zfs_fillpage()
from zpl_readpage_common(). This is consistent with the
handling in update_pages() and mappedread().
- Minor additional refactoring to comments and variable
declarations to improve readability.
- Add a test case to exercise concurrent buffered, direct,
and mmap IO to the same file.
- Reduce the mmap_sync test case default run time.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13608Closes#14498
As of the 4.13 kernel filemap_range_has_page() can be used to
check if there is a page mapped in a given file range. When
available this interface should be used which eliminates the
need for the zp->z_is_mapped boolean.
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#14493
Linux 6.2 changes the second argument of the set_acl operation to be a
"struct dentry *" rather than a "struct inode *". The inode* parameter
is still available as dentry->d_inode, so adjust the call to the _impl
function call to dereference and pass that pointer to it.
Also document that the get_acl -> get_inode_acl member name change from
commit 884a693 was an API change also introduced in Linux 6.2.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#14415
Linux 6.2 renamed the get_acl() operation to get_inode_acl() in
the inode_operations struct. This should fix Issue #14323.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#14323Closes#14331
Previously the primarycache property was handled only in the dbuf
layer. Since the speculative prefetcher is implemented in the ARC,
it had to be disabled for uncacheable buffers.
This change gives the ARC knowledge about uncacheable buffers
via arc_read() and arc_write(). So when remove_reference() drops
the last reference on the ARC header, it can either immediately destroy
it, or if it is marked as prefetch, put it into a new arc_uncached state.
That state is scanned every second, evicting stale buffers that were
not demand read.
This change also tracks dbufs that were read from the beginning,
but not to the end. It is assumed that such buffers may receive further
reads, and so they are stored in dbuf cache. If a following
reads reaches the end of the buffer, it is immediately evicted.
Otherwise it will follow regular dbuf cache eviction. Since the dbuf
layer does not know actual file sizes, this logic is not applied to
the final buffer of a dnode.
Since uncacheable buffers should no longer stay in the ARC for long,
this patch also tries to optimize I/O by allocating ARC physical
buffers as linear to allow buffer sharing.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Wilson <george.wilson@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14243
ARC code was many times significantly modified over the years, that
created significant amount of tangled and potentially broken code.
This should make arc_access()/arc_read() code some more readable.
- Decouple prefetch status tracking from b_refcnt. It made sense
originally, but became highly cryptic over the years. Move all the
logic into arc_access(). While there, clean up and comment state
transitions in arc_access(). Some transitions were weird IMO.
- Unify arc_access() calls to arc_read() instead of sometimes calling
it from arc_read_done(). To avoid extra state changes and checks add
one more b_refcnt for ARC_FLAG_IO_IN_PROGRESS.
- Reimplement ARC_FLAG_WAIT in case of ARC_FLAG_IO_IN_PROGRESS with
the same callback mechanism to not falsely account them as hits. Count
those as "iohits", an intermediate between "hits" and "misses". While
there, call read callbacks in original request order, that should be
good for fairness and random speculations/allocations/aggregations.
- Introduce additional statistic counters for prefetch, accounting
predictive vs prescient and hits vs iohits vs misses.
- Remove hash_lock argument from functions not needing it.
- Remove ARC_FLAG_PREDICTIVE_PREFETCH, since it should be opposite
to ARC_FLAG_PRESCIENT_PREFETCH if ARC_FLAG_PREFETCH is set. We may
wish to add ARC_FLAG_PRESCIENT_PREFETCH to few more places.
- Fix few false positive tests found in the process.
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14123
Linux 5.17 commit torvalds/linux@5dfbfe71e enables "the idmapping
infrastructure to support idmapped mounts of filesystems mounted
with an idmapping". Update the OpenZFS accordingly to improve the
idmapped mount support.
This pull request contains the following changes:
- xattr setter functions are fixed to take mnt_ns argument. Without
this, cp -p would fail for an idmapped mount in a user namespace.
- idmap_util is enhanced/fixed for its use in a user ns context.
- One test case added to test idmapped mount in a user ns.
Reviewed-by: Christian Brauner <christian@brauner.io>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Youzhong Yang <yyang@mathworks.com>
Closes#14097
Implement support for Linux's RENAME_* flags (for renameat2). Aside from
being quite useful for userspace (providing race-free ways to exchange
paths and implement mv --no-clobber), they are used by overlayfs and are
thus required in order to use overlayfs-on-ZFS.
In order for us to represent the new renameat2(2) flags in the ZIL, we
create two new transaction types for the two flags which need
transactional-level support (RENAME_EXCHANGE and RENAME_WHITEOUT).
RENAME_NOREPLACE does not need any ZIL support because we know that if
the operation succeeded before creating the ZIL entry, there was no file
to be clobbered and thus it can be treated as a regular TX_RENAME.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Pavel Snajdr <snajpa@snajpa.net>
Signed-off-by: Aleksa Sarai <cyphar@cyphar.com>
Closes#12209Closes#14070
This is in preparation for RENAME_EXCHANGE and RENAME_WHITEOUT support
for ZoL, but the changes here allow for far nicer fallbacks than the
previous implementation (the source and target are re-linked in case of
the final link failing).
In addition, a small cleanup was done for the "target exists but is a
different type" codepath so that it's more understandable.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Aleksa Sarai <cyphar@cyphar.com>
Closes#12209Closes#14070
Open files, which aren't present in the snapshot, which is being
roll-backed to, need to disappear from the visible VFS image of
the dataset.
Kernel provides d_drop function to drop invalid entry from
the dcache, but inode can be referenced by dentry multiple dentries.
The introduced zpl_d_drop_aliases function walks and invalidates
all aliases of an inode.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Pavel Snajdr <snajpa@snajpa.net>
Closes#9600Closes#14070
Follow up for 4938d01d which changed zio_flag from enum to uint64_t.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Youzhong Yang <yyang@mathworks.com>
Closes#14100
We ran out of space in enum zio_flag for additional flags. Rather than
introduce enum zio_flag2 and then modify a bunch of functions to take a
second flags variable, we expand the type to 64 bits via `typedef
uint64_t zio_flag_t`.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@klarasystems.com>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Co-authored-by: Richard Yao <richard.yao@klarasystems.com>
Closes#14086
Adds support for idmapped mounts. Supported as of Linux 5.12 this
functionality allows user and group IDs to be remapped without changing
their state on disk. This can be useful for portable home directories
and a variety of container related use cases.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Youzhong Yang <yyang@mathworks.com>
Closes#12923Closes#13671
There were never any users and it so happens the operation is not even
supported by rrm locks -- the macros were wrong for Linux and FreeBSD
when not using it's RMS locks.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#13906
Replace ZFS_ENTER and ZFS_VERIFY_ZP, which have hidden returns, with
functions that return error code. The reason we want to do this is
because hidden returns are not obvious and had caused some missing fail
path unwinding.
This patch changes the common, linux, and freebsd parts. Also fixes
fail path unwinding in zfs_fsync, zpl_fsync, zpl_xattr_{list,get,set}, and
zfs_lookup().
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Chunwei Chen <david.chen@nutanix.com>
Closes#13831
When building modules (as well as the kernel) with ARCH=um, the options
-Dsetjmp=kernel_setjmp and -Dlongjmp=kernel_longjmp are passed to the C
preprocessor for C files. This causes the setjmp and longjmp used in
module/lua/ldo.c to be kernel_setjmp and kernel_longjmp respectively in
the object file. However, the setjmp and longjmp that is intended to be
called is defined in an architecture dependent assembly file under the
directory module/lua/setjmp. Since it is an assembly and not a C file,
the preprocessor define is not given and the names do not change. This
becomes an issue when modpost is trying to create the Module.symvers
and sees no defined symbol for kernel_setjmp and kernel_longjmp. To fix
this, if the macro CONFIG_UML is defined, then setjmp and longjmp
macros are undefined.
When building with ARCH=um for x86 sub-architectures, CONFIG_X86 is not
defined. Instead, CONFIG_UML_X86 is defined. Despite this, the UML x86
sub-architecture can use the same object files as the x86 architectures
because the x86 sub-architecture UML kernel is running with the same
instruction set as CONFIG_X86. So the modules/Kbuild build file is
updated to add the same object files that CONFIG_X86 would add when
CONFIG_UML_X86 is defined.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Glenn Washburn <development@efficientek.com>
Closes#13547
Still descend, but only once: we get a lot of mileage out of nodist_
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13316
Page writebacks with WB_SYNC_NONE can take several seconds to complete
since they wait for the transaction group to close before being
committed. This is usually not a problem since the caller does not
need to wait. However, if we're simultaneously doing a writeback
with WB_SYNC_ALL (e.g via msync), the latter can block for several
seconds (up to zfs_txg_timeout) due to the active WB_SYNC_NONE
writeback since it needs to wait for the transaction to complete
and the PG_writeback bit to be cleared.
This commit deals with 2 cases:
- No page writeback is active. A WB_SYNC_ALL page writeback starts
and even completes. But when it's about to check if the PG_writeback
bit has been cleared, another writeback with WB_SYNC_NONE starts.
The sync page writeback ends up waiting for the non-sync page
writeback to complete.
- A page writeback with WB_SYNC_NONE is already active when a
WB_SYNC_ALL writeback starts. The WB_SYNC_ALL writeback ends up
waiting for the WB_SYNC_NONE writeback.
The fix works by carefully keeping track of active sync/non-sync
writebacks and committing when beneficial.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Shaan Nobee <sniper111@gmail.com>
Closes#12662Closes#12790
69 CSTYLED BEGINs remain, appx. 30 of which can be removed if cstyle(1)
had a useful policy regarding
CALL(ARG1,
ARG2,
ARG3);
above 2 lines. As it stands, it spits out *both*
sysctl_os.c: 385: continuation line should be indented by 4 spaces
sysctl_os.c: 385: indent by spaces instead of tabs
which is very cool
Another >10 could be fixed by removing "ulong" &al. handling.
I don't foresee anyone actually using it intentionally
(does it even exist in modern headers? why did it in the first place?).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12993
Evaluated every variable that lives in .data (and globals in .rodata)
in the kernel modules, and constified/eliminated/localised them
appropriately. This means that all read-only data is now actually
read-only data, and, if possible, at file scope. A lot of previously-
global-symbols became inlinable (and inlined!) constants. Probably
not in a big Wowee Performance Moment, but hey.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12899
When using lseek(2) to report data/holes memory mapped regions of
the file were ignored. This could result in incorrect results.
To handle this zfs_holey_common() was updated to asynchronously
writeback any dirty mmap(2) regions prior to reporting holes.
Additionally, while not strictly required, the dn_struct_rwlock is
now held over the dirty check to prevent the dnode structure from
changing. This ensures that a clean dnode can't be dirtied before
the data/hole is located. The range lock is now also taken to
ensure the call cannot race with zfs_write().
Furthermore, the code was refactored to provide a dnode_is_dirty()
helper function which checks the dnode for any dirty records to
determine its dirtiness.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Rich Ercolani <rincebrain@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #11900Closes#12724
As of the Linux 5.9 kernel a fallthrough macro has been added which
should be used to anotate all intentional fallthrough paths. Once
all of the kernel code paths have been updated to use fallthrough
the -Wimplicit-fallthrough option will because the default. To
avoid warnings in the OpenZFS code base when this happens apply
the fallthrough macro.
Additional reading: https://lwn.net/Articles/794944/
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12441
Kernel commits
332f606b32b6 ovl: enable RCU'd ->get_acl()
0cad6246621b vfs: add rcu argument to ->get_acl() callback
Added compatibility code to detect the new ->get_acl() interface
and correctly handle the case where the new rcu argument is set.
Reviewed-by: Coleman Kane <ckane@colemankane.org>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12548
Linux 4.11 added a new statx system call that allows us to expose crtime
as btime. We do this by caching crtime in the znode to match how atime,
ctime and mtime are cached in the inode.
statx also introduced a new way of reporting whether the immutable,
append and nodump bits have been set. It adds support for reporting
compression and encryption, but the semantics on other filesystems is
not just to report compression/encryption, but to allow it to be turned
on/off at the file level. We do not support that.
We could implement semantics where we refuse to allow user modification
of the bit, but we would need to do a dnode_hold() in zfs_znode_alloc()
to find out encryption/compression information. That would introduce
locking that will have a minor (although unmeasured) performance cost.
It also would be inferior to zdb, which reports far more detailed
information. We therefore omit reporting of encryption/compression
through statx in favor of recommending that users interested in such
information use zdb.
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Richard Yao <ryao@gentoo.org>
Closes#8507
Instead of clearing stats inside arc_buf_alloc_impl() do it inside
arc_hdr_alloc() and arc_release(). It fixes statistics being wiped
every time a new dbuf is filled from the ARC.
Remove b_l1hdr.b_l2_hits. L2ARC hits are accounted at b_l2hdr.b_hits.
Since the hits are accounted under hash lock, replace atomics with
simple increments.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Wilson <george.wilson@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12422
