This patch adds a command (-c) option to zpool status and zpool iostat. The
-c option allows you to run an arbitrary command on each vdev and display
the first line of output in zpool status/iostat. The environment vars
VDEV_PATH and VDEV_UPATH are set to the vdev's path and "underlying path"
before running the command. For device mapper, multipath, or partitioned
vdevs, VDEV_UPATH is the actual underlying /dev/sd* disk. This can be useful
if the command you're running requires a /dev/sd* device.
The patch also uses /sys/block/<dev>/slaves/ to lookup the underlying device
instead of using libdevmapper. This not only removes the libdevmapper
requirement at build time, but also allows you to resolve device mapper
devices without being root. This means that UDEV_UPATH get set correctly
when running zpool status/iostat as an unprivileged user.
Example:
$ zpool status -c 'echo I am $VDEV_PATH, $VDEV_UPATH'
NAME STATE READ WRITE CKSUM
mypool ONLINE 0 0 0
mirror-0 ONLINE 0 0 0
mpatha ONLINE 0 0 0 I am /dev/mapper/mpatha, /dev/sdc
sdb ONLINE 0 0 0 I am /dev/sdb1, /dev/sdb
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#5368
Allow `zfs unshare <protocol> -a` command to share or unshare all datasets
of a given protocol, nfs or smb.
Additionally, enable most of ZFS Test Suite zfs_share/zfs_unshare test cases.
To work around some Illumos-specific functionalities ($SHARE/$UNSHARE) some
function wrappers were added around them.
Finally, fix and issue in smb_is_share_active() that would leave SMB shares
exported when invoking 'zfs unshare -a'
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Turbo Fredriksson <turbo@bayour.com>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#3238Closes#5367
This patch addresses multiple 'zpool import' block device
indentification problems which are most likely to occur on a
system configured to use blkid, by_vdev paths, multipath and
failover. The symptom most commonly observed is the import
uses different path names to import the pool than would
normally be expected.
* When using blkid to identify vdevs the listed devices may
be added to the cache in any order. In order to apply the
preferred search order heuristic a zfs_path_order() function
was added to calculate the order given full path names.
* Since it's possible to have multiple block devices with
different vdev guids which refer to the same ZPOOL_CONFIG_PATH
the slice cache must be indexed by guid and name. By avoiding
collisions the preferred ordering can be maintaining even
when multiple block devices claim the same ZPOOL_CONFIG_PATH.
The preferred sorting by partition was never benefitial for
a Linux system and was removed as part of this change.
* When adding entries to the blkid cache avl_find/avl_insert
are used instead of avl_add because collisions are possible
and must be handled gracefully.
* For pools using multipath devices there are, at a minimum,
three devices where a vdev label may be read. They are the
dm-* device and each underlying /dev/sd* device. Due to the
way the block cache is implemented each of these devices may
have a different cached copy of the vdev label. This can
result in "ghost pools" which appear to persist even after
a 'zpool labelclear' has been done to the dm-* device. In
order to prevent this the vdev label is read with O_DIRECT
in order to bypass any caching to get the on-disk version.
* When opening a block device verify that vdev guid read from
the disk matches the expected vdev guid. This allows for bad
labels to be filtered out.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#5359
Previously when a drive faulted, the statechange-led.sh script would lookup
the drive's LED sysfs entry in /sys/block/sd*/device/enclosure_device, and
turn it on. During testing we noticed that if you pulled out a drive, or if
the drive was so badly broken that it no longer appeared to Linux, that the
/sys/block/sd* path would be removed, and the script could not lookup the
LED entry.
To fix this, this patch looks up the disks's more persistent
"/sys/class/enclosure/X:X:X:X/Slot N" LED sysfs path at pool import. It then
passes that path to the statechange-led script to use, rather than having the
script look it up on the fly. This allows the script to turn on/off the slot
LEDs even when the drive is missing.
Closes#5309Closes#2375
1. Enable multipath autoreplace support for FMA.
This extends FMA autoreplace to work with multipath disks. This
requires libdevmapper to be installed at build time.
2. Turn on/off fault LEDs when VDEVs become degraded/faulted/online
Set ZED_USE_ENCLOSURE_LEDS=1 in zed.rc to have ZED turn on/off the enclosure
LED for a drive when a drive becomes FAULTED/DEGRADED. Your enclosure must
be supported by the Linux SES driver for this to work. The enclosure LED
scripts work for multipath devices as well. The scripts will clear the LED
when the fault is cleared.
3. Rate limit ZIO delay and checksum events so as not to flood ZED
ZIO delay and checksum events are rate limited to 5/sec in the zfs module.
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed by: Don Brady <don.brady@intel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#2449Closes#3017Closes#5159
This first phase brings over the ZFS SLM module, zfs_mod.c, to handle
auto operations in response to disk events. Disk event monitoring is
provided from libudev and generates the expected payload schema for
zfs_mod. This work leverages the recently added devid and phys_path
strings in the vdev label.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@intel.com>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#4673
2605 want to resume interrupted zfs send
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed by: Xin Li <delphij@freebsd.org>
Reviewed by: Arne Jansen <sensille@gmx.net>
Approved by: Dan McDonald <danmcd@omniti.com>
Ported-by: kernelOfTruth <kerneloftruth@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/2605
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/9c3fd12
6980 6902 causes zfs send to break due to 32-bit/64-bit struct mismatch
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Ported by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/6980
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/ea4a67f
Porting notes:
- All rsend and snapshop tests enabled and updated for Linux.
- Fix misuse of input argument in traverse_visitbp().
- Fix ISO C90 warnings and errors.
- Fix gcc 'missing braces around initializer' in
'struct send_thread_arg to_arg =' warning.
- Replace 4 argument fletcher_4_native() with 3 argument version,
this change was made in OpenZFS 4185 which has not been ported.
- Part of the sections for 'zfs receive' and 'zfs send' was
rewritten and reordered to approximate upstream.
- Fix mktree xattr creation, 'user.' prefix required.
- Minor fixes to newly enabled test cases
- Long holds for volumes allowed during receive for minor registration.
3993 zpool(1M) and zfs(1M) should support -p for "list" and "get"
4700 "zpool get" doesn't support -H or -o options
Reviewed by: Dan McDonald <danmcd@omniti.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Ported by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/3993
OpenZFS-issue: https://www.illumos.org/issues/4700
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/c58b352
Porting notes:
I removed ZoL's zpool_get_prop_literal() in favor of
zpool_get_prop(..., boolean_t literal) since that's what OpenZFS
uses. The functionality is the same.
6544 incorrect comment in libzfs.h about offline status
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Approved by: Dan McDonald <danmcd@omniti.com>
Ported-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/6544
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/cb605c4Closes#4595
This is foundational work for ZED.
Updates a leaf vdev's persistent device strings on Linux platform
* only applies for a dedicated leaf vdev (aka whole disk)
* updated during pool create|add|attach|import
* used for matching device matching during auto-{online,expand,replace}
* stored in a leaf disk config label (i.e. alongside 'path' NVP)
* can opt-out using env var ZFS_VDEV_DEVID_OPT_OUT=YES
Some examples:
path: '/dev/sdb1'
devid: 'scsi-350000394a8ca4fbc-part1'
phys_path: 'pci-0000:04:00.0-sas-0x50000394a8ca4fbf-lun-0'
path: '/dev/mapper/mpatha'
devid: 'dm-uuid-mpath-35000c5006304de3f'
Signed-off-by: Don Brady <don.brady@intel.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2856Closes#3978Closes#4416
Add the ZFS Test Suite and test-runner framework from illumos.
This is a continuation of the work done by Turbo Fredriksson to
port the ZFS Test Suite to Linux. While this work was originally
conceived as a stand alone project integrating it directly with
the ZoL source tree has several advantages:
* Allows the ZFS Test Suite to be packaged in zfs-test package.
* Facilitates easy integration with the CI testing.
* Users can locally run the ZFS Test Suite to validate ZFS.
This testing should ONLY be done on a dedicated test system
because the ZFS Test Suite in its current form is destructive.
* Allows the ZFS Test Suite to be run directly in the ZoL source
tree enabled developers to iterate quickly during development.
* Developers can easily add/modify tests in the framework as
features are added or functionality is changed. The tests
will then always be in sync with the implementation.
Full documentation for how to run the ZFS Test Suite is available
in the tests/README.md file.
Warning: This test suite is designed to be run on a dedicated test
system. It will make modifications to the system including, but
not limited to, the following.
* Adding new users
* Adding new groups
* Modifying the following /proc files:
* /proc/sys/kernel/core_pattern
* /proc/sys/kernel/core_uses_pid
* Creating directories under /
Notes:
* Not all of the test cases are expected to pass and by default
these test cases are disabled. The failures are primarily due
to assumption made for illumos which are invalid under Linux.
* When updating these test cases it should be done in as generic
a way as possible so the patch can be submitted back upstream.
Most existing library functions have been updated to be Linux
aware, and the following functions and variables have been added.
* Functions:
* is_linux - Used to wrap a Linux specific section.
* block_device_wait - Waits for block devices to be added to /dev/.
* Variables: Linux Illumos
* ZVOL_DEVDIR "/dev/zvol" "/dev/zvol/dsk"
* ZVOL_RDEVDIR "/dev/zvol" "/dev/zvol/rdsk"
* DEV_DSKDIR "/dev" "/dev/dsk"
* DEV_RDSKDIR "/dev" "/dev/rdsk"
* NEWFS_DEFAULT_FS "ext2" "ufs"
* Many of the disabled test cases fail because 'zfs/zpool destroy'
returns EBUSY. This is largely causes by the asynchronous nature
of device handling on Linux and is expected, the impacted test
cases will need to be updated to handle this.
* There are several test cases which have been disabled because
they can trigger a deadlock. A primary example of this is to
recursively create zpools within zpools. These tests have been
disabled until the root issue can be addressed.
* Illumos specific utilities such as (mkfile) should be added to
the tests/zfs-tests/cmd/ directory. Custom programs required by
the test scripts can also be added here.
* SELinux should be either is permissive mode or disabled when
running the tests. The test cases should be updated to conform
to a standard policy.
* Redundant test functionality has been removed (zfault.sh).
* Existing test scripts (zconfig.sh) should be migrated to use
the framework for consistency and ease of testing.
* The DISKS environment variable currently only supports loopback
devices because of how the ZFS Test Suite expects partitions to
be named (p1, p2, etc). Support must be added to generate the
correct partition name based on the device location and name.
* The ZFS Test Suite is part of the illumos code base at:
https://github.com/illumos/illumos-gate/tree/master/usr/src/test
Original-patch-by: Turbo Fredriksson <turbo@bayour.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#6Closes#1534
Added by-partlabel and by-partuuid to the default device search
path. Made made device names in by-label more preferable.
Signed-off-by: Thijs Cramer <thijs.cramer@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#3892
Historically libblkid support was detected as part of configure
and optionally enabled. This was done because at the time support
for detecting ZFS pool vdevs had just be added to libblkid and
those updated packages were not yet part of many distributions.
This is no longer the case and any reasonably current distribution
will ship a version of libblkid which can detect ZFS pool vdevs.
This patch makes libblkid mandatory at build time and libblkid
the preferred method of scanning for ZFS pools. For distributions
which include a modern version of libblkid there is no change in
behavior. Explicitly scanning the default search paths is still
supported and can be enabled with the '-s' command line option.
Additionally making libblkid mandatory means that the 'zpool create'
command can reliably detect if a specified device has an existing
non-ZFS filesystem (ext4, xfs) and print a warning.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2448
The following options have been added to the zpool add, iostat,
list, status, and split subcommands. The default behavior was
not modified, from zfs(8).
-g Display vdev GUIDs instead of the normal short
device names. These GUIDs can be used in-place of
device names for the zpool detach/off‐
line/remove/replace commands.
-L Display real paths for vdevs resolving all symbolic
links. This can be used to lookup the current block
device name regardless of the /dev/disk/ path used
to open it.
-p Display full paths for vdevs instead of only the
last component of the path. This can be used in
conjunction with the -L flag.
This behavior may also be enabled using the following environment
variables.
ZPOOL_VDEV_NAME_GUID
ZPOOL_VDEV_NAME_FOLLOW_LINKS
ZPOOL_VDEV_NAME_PATH
This change is based on worked originally started by Richard Yao
to add a -g option. Then extended by @ilovezfs to add a -L option
for openzfsonosx. Those changes have been merged, re-factored,
a -p option added and extended to all relevant zpool subcommands.
Original-patch-by: Richard Yao <ryao@gentoo.org>
Extended-by: ilovezfs <ilovezfs@icloud.com>
Extended-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: ilovezfs <ilovezfs@icloud.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2011Closes#4341
6298 zfs_create_008_neg and zpool_create_023_neg need to be updated
for large block support
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
References:
https://www.illumos.org/issues/6298https://github.com/illumos/illumos-gate/commit/e9316f7
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4217
5745 zfs set allows only one dataset property to be set at a time
Reviewed by: Christopher Siden <christopher.siden@delphix.com>
Reviewed by: George Wilson <george@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Bayard Bell <buffer.g.overflow@gmail.com>
Reviewed by: Richard PALO <richard@NetBSD.org>
Reviewed by: Steven Hartland <killing@multiplay.co.uk>
Approved by: Rich Lowe <richlowe@richlowe.net>
References:
https://www.illumos.org/issues/5745https://github.com/illumos/illumos-gate/commit/3092556
Porting notes:
- Fix the missing braces around initializer, zfs_cmd_t zc = {"\0"};
- Remove extra format argument in zfs_do_set()
- Declare at the top:
- zfs_prop_t prop;
- nvpair_t *elem;
- nvpair_t *next;
- int i;
- Additionally initialize:
- int added_resv = 0;
- zfs_prop_t prop = 0;
- Assign 0 install of NULL for uint64_t types.
- zc->zc_nvlist_conf = '\0';
- zc->zc_nvlist_src = '\0';
- zc->zc_nvlist_dst = '\0';
Ported-by: kernelOfTruth kerneloftruth@gmail.com
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#3574
All fprintf() error messages are moved out of the libzfs_init()
library function where they never belonged in the first place. A
libzfs_error_init() function is added to provide useful error
messages for the most common causes of failure.
Additionally, in libzfs_run_process() the 'rc' variable was renamed
to 'error' for consistency with the rest of the code base.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chris Dunlap <cdunlap@llnl.gov>
Signed-off-by: Richard Yao <ryao@gentoo.org>
5027 zfs large block support
Reviewed by: Alek Pinchuk <pinchuk.alek@gmail.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Josef 'Jeff' Sipek <josef.sipek@nexenta.com>
Reviewed by: Richard Elling <richard.elling@richardelling.com>
Reviewed by: Saso Kiselkov <skiselkov.ml@gmail.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Dan McDonald <danmcd@omniti.com>
References:
https://www.illumos.org/issues/5027https://github.com/illumos/illumos-gate/commit/b515258
Porting Notes:
* Included in this patch is a tiny ISP2() cleanup in zio_init() from
Illumos 5255.
* Unlike the upstream Illumos commit this patch does not impose an
arbitrary 128K block size limit on volumes. Volumes, like filesystems,
are limited by the zfs_max_recordsize=1M module option.
* By default the maximum record size is limited to 1M by the module
option zfs_max_recordsize. This value may be safely increased up to
16M which is the largest block size supported by the on-disk format.
At the moment, 1M blocks clearly offer a significant performance
improvement but the benefits of going beyond this for the majority
of workloads are less clear.
* The illumos version of this patch increased DMU_MAX_ACCESS to 32M.
This was determined not to be large enough when using 16M blocks
because the zfs_make_xattrdir() function will fail (EFBIG) when
assigning a TX. This was immediately observed under Linux because
all newly created files must have a security xattr created and
that was failing. Therefore, we've set DMU_MAX_ACCESS to 64M.
* On 32-bit platforms a hard limit of 1M is set for blocks due
to the limited virtual address space. We should be able to relax
this one the ABD patches are merged.
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#354
When using 'zpool import' to scan for available pools prefer vdev names
which reference vdevs with more valid labels. There should be two labels
at the start of the device and two labels at the end of the device. If
labels are missing then the device has been damaged or is in some other
way incomplete. Preferring names with fully intact labels helps weed out
bad paths and improves the likelihood of being able to import the pool.
This behavior only applies when scanning /dev/ for valid pools. If a
cache file exists the pools described by the cache file will be used.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chris Dunlap <cdunlap@llnl.gov>
Closes#3145Closes#2844Closes#3107
If spl_hostid is set via module parameter, it's likely different from
gethostid(). Therefore, the userspace tool should read it first before
falling back to gethostid().
Signed-off-by: Chunwei Chen <tuxoko@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#3034
4757 ZFS embedded-data block pointers ("zero block compression")
4913 zfs release should not be subject to space checks
Reviewed by: Adam Leventhal <ahl@delphix.com>
Reviewed by: Max Grossman <max.grossman@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Christopher Siden <christopher.siden@delphix.com>
Reviewed by: Dan McDonald <danmcd@omniti.com>
Approved by: Dan McDonald <danmcd@omniti.com>
References:
https://www.illumos.org/issues/4757https://www.illumos.org/issues/4913https://github.com/illumos/illumos-gate/commit/5d7b4d4
Porting notes:
For compatibility with the fastpath code the zio_done() function
needed to be updated. Because embedded-data block pointers do
not require DVAs to be allocated the associated vdevs will not
be marked and therefore should not be unmarked.
Ported by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2544
zpool_events_next() can be called in blocking mode by specifying a
non-zero value for the "block" parameter. However, the design of
the ZFS Event Daemon (zed) requires additional functionality from
zpool_events_next(). Instead of adding additional arguments to the
function, it makes more sense to use flags that can be bitwise-or'd
together.
This commit replaces the zpool_events_next() int "block" parameter with
an unsigned bitwise "flags" parameter. It also defines ZEVENT_NONE
to specify the default behavior. Since non-blocking mode can be
specified with the existing ZEVENT_NONBLOCK flag, the default behavior
becomes blocking mode. This, in effect, inverts the previous use
of the "block" parameter. Existing callers of zpool_events_next()
have been modified to check for the ZEVENT_NONBLOCK flag.
Signed-off-by: Chris Dunlap <cdunlap@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #2
The ZFS_IOC_EVENTS_SEEK ioctl was added to allow user space callers
to seek around the zevent file descriptor by EID. When a specific
EID is passed and it exists the cursor will be positioned there.
If the EID is no longer cached by the kernel ENOENT is returned.
The caller may also pass ZEVENT_SEEK_START or ZEVENT_SEEK_END to seek
to those respective locations.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chris Dunlap <cdunlap@llnl.gov>
Issue #2
From time to time it may be necessary to inform the pool administrator
about an errata which impacts their pool. These errata will by shown
to the administrator through the 'zpool status' and 'zpool import'
output as appropriate. The errata must clearly describe the issue
detected, how the pool is impacted, and what action should be taken
to resolve the situation. Additional information for each errata will
be provided at http://zfsonlinux.org/msg/ZFS-8000-ER.
To accomplish the above this patch adds the required infrastructure to
allow the kernel modules to notify the utilities that an errata has
been detected. This is done through the ZPOOL_CONFIG_ERRATA uint64_t
which has been added to the pool configuration nvlist.
To add a new errata the following changes must be made:
* A new errata identifier must be assigned by adding a new enum value
to the zpool_errata_t type. New enums must be added to the end to
preserve the existing ordering.
* Code must be added to detect the issue. This does not strictly
need to be done at pool import time but doing so will make the
errata visible in 'zpool import' as well as 'zpool status'. Once
detected the spa->spa_errata member should be set to the new enum.
* If possible code should be added to clear the spa->spa_errata member
once the errata has been resolved.
* The show_import() and status_callback() functions must be updated
to include an informational message describing the errata. This
should include an action message describing what an administrator
should do to address the errata.
* The documentation at http://zfsonlinux.org/msg/ZFS-8000-ER must be
updated to describe the errata. This space can be used to provide
as much additional information as needed to fully describe the errata.
A link to this documentation will be automatically generated in the
output of 'zpool import' and 'zpool status'.
Original-idea-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Richard Yao <ryao@gentoo.or
Issue #2094
3740 Poor ZFS send / receive performance due to snapshot
hold / release processing
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Approved by: Christopher Siden <christopher.siden@delphix.com>
References:
https://www.illumos.org/issues/3740illumos/illumos-gate@a7a845e4bf
Ported-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #1775
Porting notes:
1. 13fe019870 introduced a merge conflict
in dsl_dataset_user_release_tmp where some variables were moved
outside of the preprocessor directive.
2. dea9dfefdd747534b3846845629d2200f0616dad made the previous merge
conflict worse by switching KM_SLEEP to KM_PUSHPAGE. This is notable
because this commit refactors the code, adding a new KM_SLEEP
allocation. It is not clear to me whether this should be converted
to KM_PUSHPAGE.
3. We had a merge conflict in libzfs_sendrecv.c because of copyright
notices.
4. Several small C99 compatibility fixed were made.
This change introduces zpool_get_prop_literal. It's an expanded version
of zpool_get_prop taking one additional boolean parameter. With this
parameter set to B_FALSE it will behave identically to zpool_get_prop.
Setting it to B_TRUE will return full precision numbers for the
following properties:
ZPOOL_PROP_SIZE
ZPOOL_PROP_ALLOCATED
ZPOOL_PROP_FREE
ZPOOL_PROP_FREEING
ZPOOL_PROP_EXPANDSZ
ZPOOL_PROP_ASHIFT
Also introduced is a wrapper function for zpool_get_prop making it
use zpool_get_prop_literal in the background.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #1813
When creating a new pool, or adding/replacing a disk in an existing
pool, partition tables will be automatically created on the devices.
Under normal circumstances it will take less than a second for udev
to create the expected device files under /dev/. However, it has
been observed that if the system is doing heavy IO concurrently udev
may take far longer. If you also throw in some cheap dodgy hardware
it may take even longer.
To prevent zpool commands from failing due to this the default wait
time for udev is being increased to 30 seconds. This will have no
impact on normal usage, the increase timeout should only be noticed
if your udev rules are incorrectly configured.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1646
2882 implement libzfs_core
2883 changing "canmount" property to "on" should not always remount dataset
2900 "zfs snapshot" should be able to create multiple, arbitrary snapshots at once
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Chris Siden <christopher.siden@delphix.com>
Reviewed by: Garrett D'Amore <garrett@damore.org>
Reviewed by: Bill Pijewski <wdp@joyent.com>
Reviewed by: Dan Kruchinin <dan.kruchinin@gmail.com>
Approved by: Eric Schrock <Eric.Schrock@delphix.com>
References:
https://www.illumos.org/issues/2882https://www.illumos.org/issues/2883https://www.illumos.org/issues/2900illumos/illumos-gate@4445fffbbb
Ported-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1293
Porting notes:
WARNING: This patch changes the user/kernel ABI. That means that
the zfs/zpool utilities built from master are NOT compatible with
the 0.6.2 kernel modules. Ensure you load the matching kernel
modules from master after updating the utilities. Otherwise the
zfs/zpool commands will be unable to interact with your pool and
you will see errors similar to the following:
$ zpool list
failed to read pool configuration: bad address
no pools available
$ zfs list
no datasets available
Add zvol minor device creation to the new zfs_snapshot_nvl function.
Remove the logging of the "release" operation in
dsl_dataset_user_release_sync(). The logging caused a null dereference
because ds->ds_dir is zeroed in dsl_dataset_destroy_sync() and the
logging functions try to get the ds name via the dsl_dataset_name()
function. I've got no idea why this particular code would have worked
in Illumos. This code has subsequently been completely reworked in
Illumos commit 3b2aab1 (3464 zfs synctask code needs restructuring).
Squash some "may be used uninitialized" warning/erorrs.
Fix some printf format warnings for %lld and %llu.
Apply a few spa_writeable() changes that were made to Illumos in
illumos/illumos-gate.git@cd1c8b8 as part of the 3112, 3113, 3114 and
3115 fixes.
Add a missing call to fnvlist_free(nvl) in log_internal() that was added
in Illumos to fix issue 3085 but couldn't be ported to ZoL at the time
(zfsonlinux/zfs@9e11c73) because it depended on future work.
The FreeBSD implementation of zfs adds the 'zpool labelclear'
command. Since this functionality is helpful and straight
forward to add it is being included in ZoL.
References:
freebsd/freebsd@119a041dc9
Ported-by: Dmitry Khasanov <pik4ez@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1126
In the interest of maintaining only one udev helper to give vdevs
user friendly names, the zpool_id and zpool_layout infrastructure
is being retired. They are superseded by vdev_id which incorporates
all the previous functionality.
Documentation for the new vdev_id(8) helper and its configuration
file, vdev_id.conf(5), can be found in their respective man pages.
Several useful example files are installed under /etc/zfs/.
/etc/zfs/vdev_id.conf.alias.example
/etc/zfs/vdev_id.conf.multipath.example
/etc/zfs/vdev_id.conf.sas_direct.example
/etc/zfs/vdev_id.conf.sas_switch.example
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#981
2762 zpool command should have better support for feature flags
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Approved by: Eric Schrock <Eric.Schrock@delphix.com>
References:
illumos/illumos-gate@57221772c3https://www.illumos.org/issues/2762
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
2619 asynchronous destruction of ZFS file systems
2747 SPA versioning with zfs feature flags
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <gwilson@delphix.com>
Reviewed by: Richard Lowe <richlowe@richlowe.net>
Reviewed by: Dan Kruchinin <dan.kruchinin@gmail.com>
Approved by: Eric Schrock <Eric.Schrock@delphix.com>
References:
illumos/illumos-gate@53089ab7c8illumos/illumos-gate@ad135b5d64
illumos changeset: 13700:2889e2596bd6
https://www.illumos.org/issues/2619https://www.illumos.org/issues/2747
NOTE: The grub specific changes were not ported. This change
must be made to the Linux grub packages.
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
The 'zpool replace' command would fail when given a short name
because unlike on other platforms the short name cannot be
deterministically expanded to a single path. Multiple path
prefixes must be checked and in addition the partition suffix
for whole disks is determined by the prefix.
To handle this complexity a zfs_strcmp_pathname() function was
added which takes either a short or fully qualified device name.
Short names will be expanded using the prefixes in the default
import search path, or the ZPOOL_IMPORT_PATH environment variable
if it's defined. All posible expansions are then compared against
the comparison path. Care is taken to strip redundant slashes to
ensure legitimate matches are not missed.
In the context of this work the existing zfs_resolve_shortname()
function was extended to consider the ZPOOL_IMPORT_PATH when set.
The zfs_append_partition() interface was also simplified to take
only a single buffer.
The vast majority of these changes rework existing Linux specific
code which was originally written to accomidate udev. However,
there is some minimal cleanup which removes Illumos specific code.
This was done to improve readability but the basic flow and intent
of the upstream code was maintained.
These changes are the logical conclusion of the previos work to
adjust the 'zpool import' search behavior, see commit 44867b6a.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#544Closes#976
Reviewed by: Matt Ahrens <matt@delphix.com>
Reviewed by: George Wilson <George.Wilson@delphix.com>
Reviewed by: Bill Pijewski <wdp@joyent.com>
Reviewed by: Richard Elling <richard.elling@richardelling.com>
Approved by: Richard Lowe <richlowe@richlowe.net>
References:
https://www.illumos.org/issues/2635
Ported by: Martin Matuska <martin@matuska.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#717
1644 add ZFS "clones" property
1645 add ZFS "written" and "written@..." properties
1646 "zfs send" should estimate size of stream
1647 "zfs destroy" should determine space reclaimed by
destroying multiple snapshots
1708 adjust size of zpool history data
References:
https://www.illumos.org/issues/1644https://www.illumos.org/issues/1645https://www.illumos.org/issues/1646https://www.illumos.org/issues/1647https://www.illumos.org/issues/1708
This commit modifies the user to kernel space ioctl ABI. Extra
care should be taken when updating to ensure both the kernel
modules and utilities are updated. This change has reordered
all of the new ioctl()s to the end of the list. This should
help minimize this issue in the future.
Reviewed by: Richard Lowe <richlowe@richlowe.net>
Reviewed by: George Wilson <gwilson@zfsmail.com>
Reviewed by: Albert Lee <trisk@opensolaris.org>
Approved by: Garrett D'Amore <garret@nexenta.com>
Ported by: Martin Matuska <martin@matuska.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#826Closes#664
Reviewed by: George Wilson <gwilson@zfsmail.com>
Reviewed by: Igor Kozhukhov <ikozhukhov@gmail.com>
Reviewed by: Alexander Eremin <alexander.eremin@nexenta.com>
Reviewed by: Alexander Stetsenko <ams@nexenta.com>
Approved by: Richard Lowe <richlowe@richlowe.net>
References:
https://www.illumos.org/issues/1748
This commit modifies the user to kernel space ioctl ABI. Extra
care should be taken when updating to ensure both the kernel
modules and utilities are updated. If only the user space
component is updated both the 'zpool events' command and the
'zpool reguid' command will not work until the kernel modules
are updated.
Ported by: Martin Matuska <martin@matuska.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#665
FreeBSD #xxx: Dramatically optimize listing snapshots when user
requests only snapshot names and wants to sort them by name, ie.
when executes:
# zfs list -t snapshot -o name -s name
Because only name is needed we don't have to read all snapshot
properties.
Below you can find how long does it take to list 34509 snapshots
from a single disk pool before and after this change with cold and
warm cache:
before:
# time zfs list -t snapshot -o name -s name > /dev/null
cold cache: 525s
warm cache: 218s
after:
# time zfs list -t snapshot -o name -s name > /dev/null
cold cache: 1.7s
warm cache: 1.1s
NOTE: This patch only appears in FreeBSD. If/when Illumos picks up
the change we may want to drop this patch and adopt their version.
However, for now this addresses a real issue.
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #450
The .get_sb callback has been replaced by a .mount callback
in the file_system_type structure. When using the new
interface the caller must now use the mount_nodev() helper.
Unfortunately, the new interface no longer passes the vfsmount
down to the zfs layers. This poses a problem for the existing
implementation because we currently save this pointer in the
super block for latter use. It provides our only entry point
in to the namespace layer for manipulating certain mount options.
This needed to be done originally to allow commands like
'zfs set atime=off tank' to work properly. It also allowed me
to keep more of the original Solaris code unmodified. Under
Solaris there is a 1-to-1 mapping between a mount point and a
file system so this is a fairly natural thing to do. However,
under Linux they many be multiple entries in the namespace
which reference the same filesystem. Thus keeping a back
reference from the filesystem to the namespace is complicated.
Rather than introduce some ugly hack to get the vfsmount and
continue as before. I'm leveraging this API change to update
the ZFS code to do things in a more natural way for Linux.
This has the upside that is resolves the compatibility issue
for the long term and fixes several other minor bugs which
have been reported.
This commit updates the code to remove this vfsmount back
reference entirely. All modifications to filesystem mount
options are now passed in to the kernel via a '-o remount'.
This is the expected Linux mechanism and allows the namespace
to properly handle any options which apply to it before passing
them on to the file system itself.
Aside from fixing the compatibility issue, removing the
vfsmount has had the benefit of simplifying the code. This
change which fairly involved has turned out nicely.
Closes#246Closes#217Closes#187Closes#248Closes#231
Because we are dependent of the system mount/umount utilities to
ensure correct mtab locking, we should not suppress their error
output. During a successful mount/umount they will be silent,
but during a failure the error message they print is the only sure
way to know why a mount failed. This is because the (u)mount(8)
return code does not contain the result of the system call issued.
The only way to clearly idenify why thing failed is to rely on
the error message printed by the tool.
Longer term once libmount is available we can issue the mount/umount
system calls within the tool and still be ensured correct mtab locking.
Closed#107
