The txg_sync(), zfs_putpage(), zvol_write(), and zvol_discard()
call paths must only use KM_PUSHPAGE to avoid potential deadlocks
during direct reclaim.
This patch annotates these call paths so any accidental use of
KM_SLEEP will be quickly detected. In the interest of stability
if debugging is disabled the offending allocation will have its
GFP flags automatically corrected. When debugging is enabled
any misuse will be treated as a fatal error.
This patch is entirely for debugging. We should be careful to
NOT become dependant on it fixing up the incorrect allocations.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Commit eec8164771 worked around an issue
involving direct reclaim through the use of PF_MEMALLOC. Since we
are reworking thing to use KM_PUSHPAGE so that swap works, we revert
this patch in favor of the use of KM_PUSHPAGE in the affected areas.
Signed-off-by: Richard Yao <ryao@cs.stonybrook.edu>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #726
After surveying the code, the few places where smp_processor_id is used
were deemed to be safe to use with a preempt enabled kernel. As such, no
core logic had to be changed. These smp_processor_id call sites are simply
are wrapped in kpreempt_disable and kpreempt_enabled to prevent the
Linux kernel from emitting scary warnings.
Signed-off-by: Prakash Surya <surya1@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <ryao@cs.stonybrook.edu>
Issue #83
Keep counters for the various reasons that a thread may end up
in txg_wait_open() waiting on a new txg. This can be useful
when attempting to determine why a particular workload is
under performing.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
The function txg_delay() is used to delay txg (transaction group)
threads in ZFS. The timeout value for this function is calculated
using:
int timeout = ddi_get_lbolt() + ticks;
Later, the actual wait is performed:
while (ddi_get_lbolt() < timeout &&
tx->tx_syncing_txg < txg-1 && !txg_stalled(dp))
(void) cv_timedwait(&tx->tx_quiesce_more_cv, &tx->tx_sync_lock,
timeout - ddi_get_lbolt());
The ddi_get_lbolt() function returns current uptime in clock ticks
and is typed as clock_t. The clock_t type on 64-bit architectures
is int64_t.
The "timeout" variable will overflow depending on the tick frequency
(e.g. for 1000 it will overflow in 28.855 days). This will make the
expression "ddi_get_lbolt() < timeout" always false - txg threads will
not be delayed anymore at all. This leads to a slowdown in ZFS writes.
The attached patch initializes timeout as clock_t to match the return
value of ddi_get_lbolt().
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #352
Disable the normal reclaim path for the txg_sync thread. This
ensures the thread will never enter dmu_tx_assign() which can
otherwise occur due to direct reclaim. If this is allowed to
happen the system can deadlock. Direct reclaim call path:
->shrink_icache_memory->prune_icache->dispose_list->
clear_inode->zpl_clear_inode->zfs_inactive->dmu_tx_assign
Kernel threads which sleep uninterruptibly on Linux are marked in the (D)
state. These threads are usually in the process of performing IO and are
thus counted against the load average. The txg_quiesce and txg_sync threads
were always sleeping uninterruptibly and thus inflating the load average.
This change makes them sleep interruptibly. Some care is required however
because these threads may now be woken early by signals. In this case the
callers are all careful to check that the required conditions are met after
waking up. If we're woken early due to a signal they will simply go back
to sleep. In this case these changes are safe.
Closes#175
This adds an API to wait for pending commit callbacks of already-synced
transactions to finish processing. This is needed by the DMU-OSD in
Lustre during device finalization when some callbacks may still not be
called, this leads to non-zero reference count errors. See lustre.org
bug 23931.
The upstream commit cb code had a few bugs:
1) The arguments of the list_move_tail() call in txg_dispatch_callbacks()
were reversed by mistake. This caused the commit callbacks to not be
called at all.
2) ztest had a bug in ztest_dmu_commit_callbacks() where "error" was not
initialized correctly. This seems to have caused the test to always take
the simulated error code path, which made ztest unable to detect whether
commit cbs were being called for transactions that successfuly complete.
3) ztest had another bug in ztest_dmu_commit_callbacks() where the commit
cb threshold was not being compared correctly.
4) The commit cb taskq was using 'max_ncpus * 2' as the maxalloc argument
of taskq_create(), which could have caused unnecessary delays in the txg
sync thread.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
