While the autoexpand property may seem like a small feature it
depends on a significant amount of system infrastructure. Enough
of that infrastructure is now in place that with a few modifications
for Linux it can be supported.
Auto-expand works as follows; when a block device is modified
(re-sized, closed after being open r/w, etc) a change uevent is
generated for udev. The ZED, which is monitoring udev events,
passes the change event along to zfs_deliver_dle() if the disk
or partition contains a zfs_member as identified by blkid.
From here the device is matched against all imported pool vdevs
using the vdev_guid which was read from the label by blkid. If
a match is found the ZED reopens the pool vdev. This re-opening
is important because it allows the vdev to be briefly closed so
the disk partition table can be re-read. Otherwise, it wouldn't
be possible to report the maximum possible expansion size.
Finally, if the property autoexpand=on a vdev expansion will be
attempted. After performing some sanity checks on the disk to
verify that it is safe to expand, the primary partition (-part1)
will be expanded and the partition table updated. The partition
is then re-opened (again) to detect the updated size which allows
the new capacity to be used.
In order to make all of the above possible the following changes
were required:
* Updated the zpool_expand_001_pos and zpool_expand_003_pos tests.
These tests now create a pool which is layered on a loopback,
scsi_debug, and file vdev. This allows for testing of non-
partitioned block device (loopback), a partition block device
(scsi_debug), and a file which does not receive udev change
events. This provided for better test coverage, and by removing
the layering on ZFS volumes there issues surrounding layering
one pool on another are avoided.
* zpool_find_vdev_by_physpath() updated to accept a vdev guid.
This allows for matching by guid rather than path which is a
more reliable way for the ZED to reference a vdev.
* Fixed zfs_zevent_wait() signal handling which could result
in the ZED spinning when a signal was not handled.
* Removed vdev_disk_rrpart() functionality which can be abandoned
in favor of kernel provided blkdev_reread_part() function.
* Added a rwlock which is held as a writer while a disk is being
reopened. This is important to prevent errors from occurring
for any configuration related IOs which bypass the SCL_ZIO lock.
The zpool_reopen_007_pos.ksh test case was added to verify IO
error are never observed when reopening. This is not expected
to impact IO performance.
Additional fixes which aren't critical but were discovered and
resolved in the course of developing this functionality.
* Added PHYS_PATH="/dev/zvol/dataset" to the vdev configuration for
ZFS volumes. This is as good as a unique physical path, while the
volumes are not used in the test cases anymore for other reasons
this improvement was included.
Reviewed by: Richard Elling <Richard.Elling@RichardElling.com>
Signed-off-by: Sara Hartse <sara.hartse@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#120Closes#2437Closes#5771Closes#7366Closes#7582Closes#7629
1. Add a proc entry to display the pool's state:
$ cat /proc/spl/kstat/zfs/tank/state
ONLINE
This is done without using the spa config locks, so it will
never hang.
2. Fix 'zpool status' and 'zpool list -o health' output to print
"SUSPENDED" instead of "ONLINE" for suspended pools.
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Richard Elling <Richard.Elling@RichardElling.com>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#7331Closes#7563
Due to zpool create auto-partioning in Linux (i.e. sdb1),
certain utilities need to use the parition (sdb1) while
others use the whole disk name (sdb).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Zuchowski <pzuchowski@datto.com>
Closes#6939Closes#7261
* Teach ZED to handle spares usingi the configured ashift: if the zpool
'ashift' property is set then ZED should use its value when kicking
in a hotspare; with this change 512e disks can be used as spares
for VDEVs that were created with ashift=9, even if ZFS natively
detects them as 4K block devices.
* Introduce an additional auto_spare test case which verifies that in
the face of multiple device failures an appropiate number of spares
are kicked in.
* Fix zed_stop() in "libtest.shlib" which did not correctly wait the
target pid.
* Fix ZED crashing on startup caused by a race condition in libzfs
when used in multi-threaded context.
* Convert ZED over to using the tpool library which is already present
in the Illumos FMA code.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#2562Closes#6858
Added -n flag to zpool reopen that allows a running scrub
operation to continue if there is a device with Dirty Time Log.
By default if a component device has a DTL and zpool reopen
is executed all running scan operations will be restarted.
Added functional tests for `zpool reopen`
Tests covers following scenarios:
* `zpool reopen` without arguments,
* `zpool reopen` with pool name as argument,
* `zpool reopen` while scrubbing,
* `zpool reopen -n` while scrubbing,
* `zpool reopen -n` while resilvering,
* `zpool reopen` with bad arguments.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: Arkadiusz Bubała <arkadiusz.bubala@open-e.com>
Closes#6076Closes#6746
