Sponsored-by: https://despairlabs.com/sponsor/
Signed-off-by: Rob Norris <robn@despairlabs.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Linux was missing a default value for DEV_DSKDIR. Set it to /dev.
Fix resulting fallout.
SLICE_PREFIX seems like a good candidate for including in the defaults.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#9898
The root cause of these failures is that udev can notify the
ZED of newly created partition before its links are created.
Handle this by allowing an auto-replace to briefly wait until
udev confirms the links exist.
Distill this test case down to its essentials so it can be run
reliably. What we need to check is that:
1) A new disk, in the same physical location, is automatically
brought online when added to the system,
2) It completes the replacement process, and
3) The pool is now ONLINE and healthy.
There is no need to remove the scsi_debug module. After exporting
the pool the disk can be zeroed, removed, and then re-added to the
system as a new disk.
Reviewed by: loli10K <ezomori.nozomu@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8051
Most kshlib files are imported by other scripts
and do not have a shebang at the top of their files.
Make all kshlib follow this convention.
Remove shebangs from cfg files as well.
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Close#7406
The ZED is expected to automatically kick in a hot spare device
when there's one available in the pool and a sufficient number of
read errors have been encountered. Use zinject to simulate the
failure condition and verify the hot spare is used.
auto_spare_001_pos.ksh: read IO errors, the vdev is FAULTED
auto_spare_002_pos.ksh: read CHECKSUM errors, the vdev is DEGRADE
Reviewed by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: David Quigley <david.quigley@intel.com>
Closes#6280
Enable most of the remaining test cases which were previously
disabled. The required fixes are as follows:
* cache_001_pos - No changes required.
* cache_010_neg - Updated to use losetup under Linux. Loopback
cache devices are allowed, ZVOLs as cache devices are not.
Disabled until all the builders pass reliably.
* cachefile_001_pos, cachefile_002_pos, cachefile_003_pos,
cachefile_004_pos - Set set_device_dir path in cachefile.cfg,
updated CPATH1 and CPATH2 to reference unique files.
* zfs_clone_005_pos - Wait for udev to create volumes.
* zfs_mount_007_pos - Updated mount options to expected Linux names.
* zfs_mount_009_neg, zfs_mount_all_001_pos - No changes required.
* zfs_unmount_005_pos, zfs_unmount_009_pos, zfs_unmount_all_001_pos -
Updated to expect -f to not unmount busy mount points under Linux.
* rsend_019_pos - Observed to occasionally take a long time on both
32-bit systems and the kmemleak builder.
* zfs_written_property_001_pos - Switched sync(1) to sync_pool.
* devices_001_pos, devices_002_neg - Updated create_dev_file() helper
for Linux.
* exec_002_neg.ksh - Fixed mmap_exec.c to preserve errno. Updated
test case to expect EPERM from Linux as described by mmap(2).
* grow_pool_001_pos - Adding missing setup.ksh and cleanup.ksh
scripts from OpenZFS.
* grow_replicas_001_pos.ksh - Added missing $SLICE_* variables.
* history_004_pos, history_006_neg, history_008_pos - Fixed by
previous commits and were not enabled. No changes required.
* zfs_allow_010_pos - Added missing spaces after assorted zfs
commands in delegate_common.kshlib.
* inuse_* - Illumos dump device tests skipped. Remaining test
cases updated to correctly create required partitions.
* large_files_001_pos - Fixed largest_file.c to accept EINVAL
as well as EFBIG as described in write(2).
* link_count_001 - Added nproc to required commands.
* umountall_001 - Updated to use umount -a.
* online_offline_001_* - Pull in OpenZFS change to file_trunc.c
to make the '-c 0' option run the test in a loop. Included
online_offline.cfg file in all test cases.
* rename_dirs_001_pos - Updated to use the rename_dir test binary,
pkill restricted to exact matches and total runtime reduced.
* slog_013_neg, write_dirs_002_pos - No changes required.
* slog_013_pos.ksh - Updated to use losetup under Linux.
* slog_014_pos.ksh - ZED will not be running, manually degrade
the damaged vdev as expected.
* nopwrite_varying_compression, nopwrite_volume - Forced pool
sync with sync_pool to ensure up to date property values.
* Fixed typos in ZED log messages. Refactored zed_* helper
functions to resolve all-syslog exit=1 errors in zedlog.
* zfs_copies_005_neg, zfs_get_004_pos, zpool_add_004_pos,
zpool_destroy_001_pos, largest_pool_001_pos, clone_001_pos.ksh,
clone_001_pos, - Skip until layering pools on zvols is solid.
* largest_pool_001_pos - Limited to 7eb pool, maximum
supported size in 8eb-1 on Linux.
* zpool_expand_001_pos, zpool_expand_003_neg - Requires
additional support from the ZED, updated skip reason.
* zfs_rollback_001_pos, zfs_rollback_002_pos - Properly cleanup
busy mount points under Linux between test loops.
* privilege_001_pos, privilege_003_pos, rollback_003_pos,
threadsappend_001_pos - Skip with log_unsupported.
* snapshot_016_pos - No changes required.
* snapshot_008_pos - Increased LIMIT from 512K to 2M and added
sync_pool to avoid false positives.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6128
Authored by: John Wren Kennedy <john.kennedy@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Dan McDonald <danmcd@omniti.com>
Approved by: Gordon Ross <gordon.w.ross@gmail.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: George Melikov <mail@gmelikov.ru>
Porting Notes:
- Utilities which aren't available under Linux have been removed.
- Because of sudo's default secure path behavior PATH must be
explicitly reset at the top of libtest.shlib. This avoids the
need for all users to customize secure path on their system.
- Updated ZoL infrastructure to manage constrained path
- Updated all test cases
- Check permissions for usergroup tests
- When testing in-tree create links under bin/
- Update fault cleanup such that missing files during
cleanup aren't fatal.
- Configure su environment with constrained path
OpenZFS-issue: https://www.illumos.org/issues/7290
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/1d32ba6Closes#5903
Also included are updates to auto-online test
Automated auto-replace test to go along with ZED FMA integration
(PR 4673) auto-replace_001.pos works using a scsi_debug device
(the only usable virtual device currently due to whole_disk var
needing to be set)
Functionality for automated FMA auto-replace test to work with
scsi_debug devs: Some functionality/exceptions needed to be
added for automation of auto-replace to work correctly.
In the test an alias vdev_id rule is added for any scsi_debug
device which sets the phys_path="scsidebug" after a udevadm
trigger command.
A symlink is created for the vdev_id.conf file (in /etc/zfs/ by
default) to be used in-tree for the test suite
(/var/tmp/zfs/vdev_id.conf). "./scripts/zfs-helpers.sh -i" needs
to be run before fault tests in the ZTS (to use udev rules in-tree)
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Don Brady <don.brady@intel.com>
Reviewed-by: David Quigley <david.quigley@intel.com>
Signed-off-by: Sydney Vanda <sydney.m.vanda@intel.com>
Closes#5944
Automated auto-online test to go along with ZED FMA integration (PR 4673)
auto_online_001.pos works with real devices (sd- and mpath) and with non-real
block devices (loop) by adding a scsi_debug device to the pool
Note: In order for test group to run, ZED must not currently be running.
Kernel 3.16.37 or higher needed for scsi_debug to work properly
If timeout occurs on test using a scsi_debug device (error noticed on Ubuntu
system), a reboot might be needed in order for test to pass. (more
investigation into this)
Also suppressed output from is_real_device/is_loop_device/is_mpath_device -
was making the log file very cluttered with useless error messages
"ie /dev/mapper/sdc is not a block device" from previous patch
Reviewed-by: Don Brady <don.brady@intel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: David Quigley <david.quigley@intel.com>
Signed-off-by: Sydney Vanda <sydney.m.vanda@intel.com>
Closes#5774
