Verify that all empty sectors are zero filled before using them to
calculate parity. Failure to do so can result in incorrect parity
columns being generated and written to disk if the contents of an
empty sector are non-zero. This was possible because the checksum
only protects the data portions of the buffer, not the empty sector
padding.
This issue has been addressed by updating raidz_parity_verify() to
check that all dRAID empty sectors are zero filled. Any sectors
which are non-zero will be fixed, repair IO issued, and a checksum
error logged. They can then be safely used to verify the parity.
This specific type of damage is unlikely to occur since it requires
a disk to have silently returned bad data, for an empty sector, while
performing a scrub. However, if a pool were to have been damaged
in this way, scrubbing the pool with this change applied will repair
both the empty sector and parity columns as long as the data checksum
is valid. Checksum errors will be reported in the `zpool status`
output for any repairs which are made.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12857
When performing I/O on FreeBSD using a file based vdev ensure all
errors encountered when reading/writing are propagated through the
zio pipeline.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12904
This is a follow up commit for e03a41a60 which aimed to resolve
this same test failure. The core "problem" here is that it takes
very little space to perform a clone/snapshot/bookmark, which
means if we want these commands to reliably fail the pool must
truely have exhausted all free space.
This commit increases the number of fill iterations to try and
consume every block which we can. This still can't guarantee
the clone/snapshot/bookmark will fail, but it significantly
improves the odds. The exception was kept since it's still
not a sure thing.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12903
On FreeBSD vnode reclamation is single-threaded, protected by single
global lock. Linux seems to be able to use a thread per mount point,
but at this time it creates more harm than good.
Reduce number of threads to 1, adding tunable in case somebody wants
to try more.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Chris Dunlop <chris@onthe.net.au>
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#12896
Issue #9966
Under Linux when rolling back a mounted filesystem negative dentries
may not be dropped from the cache. This can result in an ENOENT
being incorrectly returned on first access. Issuing a `df` before
the unmount results in the negative dentries being invalidated and
side steps the issue.
This is solely a workaround for the test case on Linux and not
correct behavior. The core issue of invalidating negative dentries
needs to be handled with a kernel side change. This is being
tracked as issue #6143.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12898
Issue #6143
The rerefreserv_raidz test was failing on Linux because the sync being
issued doesn't guarantee a pool sync. Switch to using the sync_pool
function and remove the ZTS exception for Linux.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12897
The build on musl needs linux/fs.h for SEEK_DATA and friends,
and sys/sysmacros.h for P2ROUNDUP. Add the needed headers.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Georgy Yakovlev <gyakovlev@gentoo.org>
Closes#12891
Bullseye shellcheck picks these up as SC2140, and it's right!
@LIBFETCH_SONAME@ is already quoted, so dracut had
"$d/"libcurl.so.4""
and i-t had
""libcurl.so.4""
Partially reverts 34eef3e9a7 (#12760),
which broke this
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12835
