... instead of list_head() + list_remove(). On FreeBSD the list
functions are not inlined, so in addition to more compact code
this also saves another function call.
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14955
Before allowing the ZED to mark a vdev as REMOVED due to a
hotplug event confirm that it is non-responsive with probe.
Any device which can be successfully probed should be left
ONLINE to prevent a healthy pool from being incorrectly
SUSPENDED. This may occur for at least the following two
scenarios.
1) Drive expansion (zpool online -e) in VMware environments.
If, during the partition resize operation, a partition is
removed and re-created then udev will send a removed event.
2) Re-scanning the namespaces of an NVMe device (nvme ns-rescan)
may result in a udev remove and add event being delivered.
Finally, update the ZED to only kick in a spare when the
removal was successful.
Reviewed-by: Ameer Hamza <ahamza@ixsystems.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #14859Closes#14861
After addressing coverity complaints involving `nvpair_name()`, the
compiler started complaining about dropping const. This lead to a rabbit
hole where not only `nvpair_name()` needed to be constified, but also
`nvpair_value_string()`, `fnvpair_value_string()` and a few other static
functions, plus variable pointers throughout the code. The result became
a fairly big change, so it has been split out into its own patch.
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14612
Introduce four new vdev properties:
checksum_n
checksum_t
io_n
io_t
These properties can be used for configuring the thresholds of zed's
diagnosis engine and are interpeted as <N> events in T <seconds>.
When this property is set to a non-default value on a top-level vdev,
those thresholds will also apply to its leaf vdevs. This behavior can be
overridden by explicitly setting the property on the leaf vdev.
Note that, these properties do not persist across vdev replacement. For
this reason, it is advisable to set the property on the top-level vdev
instead of the leaf vdev.
The default values for zed's diagnosis engine (10 events, 600 seconds)
remains unchanged.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Rob Wing <rob.wing@klarasystems.com>
Sponsored-by: Seagate Technology LLC
Closes#13805
This commit supports for spare vdev hotplug. The
spare vdev associated with all the pools will be
marked as "Removed" when the drive is physically
detached and will become "Available" when the
drive is reattached. Currently, the spare vdev
status does not change on the drive removal and
the same is the case with reattachment.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#14295
If the attached disk already contains a vdev GUID, it
means the disk is not clean. In such a scenario, the
physical path would be a match that makes the disk
faulted when trying to online it. So, we would only
want to proceed if either GUID matches with the last
attached disk or the disk is in a clean state.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#14181
zed aborts and dumps core in vdev_whole_disk_from_config() if
wholedisk property does not exist. make_leaf_vdev() adds the
property but there may be already pools that don't have the
wholedisk in the label.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#14062
Coverity complained about a couple of uninitialized value reads in ZED.
* zfs_deliver_dle() can pass an uninitialized string to zed_log_msg()
* An uninitialized sev.sigev_signo is passed to timer_create()
The former would log garbage while the latter is not a real issue, but
we might as well suppress it by initializing the field to 0 for
consistency's sake.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14047
GCC 12.1.1_p20220625's static analyzer caught these.
Of the two in the btree test, one had previously been caught by Coverity
and Smatch, but GCC flagged it as a false positive. Upon examining how
other test cases handle this, the solution was changed from
`ASSERT3P(node, !=, NULL);` to using `perror()` to be consistent with
the fixes to the other fixes done to the ZTS code.
That approach was also used in ZED since I did not see a better way of
handling this there. Also, upon inspection, additional unchecked
pointers from malloc()/calloc()/strdup() were found in ZED, so those
were handled too.
In other parts of the code, the existing methods to avoid issues from
memory allocators returning NULL were used, such as using
`umem_alloc(size, UMEM_NOFAIL)` or returning `ENOMEM`.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13979
ZED does not take any action for disk removal events if there is no
spare VDEV available. Added zpool_vdev_remove_wanted() in libzfs
and vdev_remove_wanted() in vdev.c to remove the VDEV through ZED
on removal event. This means that if you are running zed and
remove a disk, it will be properly marked as REMOVED.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#13797
Coverity complained about unchecked return values and unused values that
turned out to be unused return values.
Different approaches were used to handle the different cases of
unchecked return values:
* cmd/zdb/zdb.c: VERIFY0 was used in one place since the existing code
had no error handling. An error message was printed in another to
match the rest of the code.
* cmd/zed/agents/zfs_retire.c: We dismiss the return value with `(void)`
because the value is expected to be potentially unset.
* cmd/zpool_influxdb/zpool_influxdb.c: We dismiss the return value with
`(void)` because the values are expected to be potentially unset.
* cmd/ztest.c: VERIFY0 was used since we want failures if something goes
wrong in ztest.
* module/zfs/dsl_dir.c: We dismiss the return value with `(void)`
because there is no guarantee that the zap entry will always be there.
For example, old pools imported readonly would not have it and we do
not want to fail here because of that.
* module/zfs/zfs_fm.c: `fnvlist_add_*()` was used since the
allocations sleep and thus can never fail.
* module/zfs/zvol.c: We dismiss the return value with `(void)` because
we do not need it. This matches what is already done in the analogous
`zfs_replay_write2()`.
* tests/zfs-tests/cmd/draid.c: We suppress one return value with
`(void)` since the code handles errors already. The other return value
is handled by switching to `fnvlist_lookup_uint8_array()`.
* tests/zfs-tests/cmd/file/file_fadvise.c: We add error handling.
* tests/zfs-tests/cmd/mmap_sync.c: We add error handling for munmap, but
ignore failures on remove() with (void) since it is expected to be
able to fail.
* tests/zfs-tests/cmd/mmapwrite.c: We add error handling.
As for unused return values, they were all in places where there was
error handling, so logic was added to handle the return values.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13920
Coverity complained about this.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Chunwei Chen <david.chen@nutanix.com>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13903
Coverity complained about the format specifiers not matching variables.
In one case, the variable is a constant, so we fix it. In another, we
were missing an argument (about which coverity also complained).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13888
Users were seeing floods of `config_sync` events when autoexpand was
enabled. This happened because all "disk status change" udev events
invoke the autoexpand codepath, which calls zpool_relabel_disk(),
which in turn cause another "disk status change" event to happen,
in a feedback loop. Note that "disk status change" happens every time
a user calls close() on a block device.
This commit breaks the feedback loop by only allowing an autoexpand
to happen if the disk actually changed size.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes: #7132Closes: #7366Closes#13729
When scrubbing/resilvering a pool it can be counter productive to
cancel the scan and kick of a replace operation to a hot spare
when encountering checksum errors. In this case, the best course
of action is to allow the scrub/resilver to complete as quickly
as possible and to keep the vdevs fully online if possible.
Realistically, this is less of an issue for a RAIDZ since a
traditional resilver must be used and checksums will be verified.
However, this is not the case for a mirror or dRAID pool which is
sequentially resilvered and checksum verification is deferred
until after the replace operation completes.
Regardless, we apply this policy to all pool types since it's
a good idea for all vdevs. Degrading additional vdevs has the
potential to make a bad situation worse. Note the checksum
errors will still be reported as both an event and by
`zpool status`. This change only prevents the ZED from
proactively taking any action.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13499
Clang trunk now warns -Wstrict-prototypes on this, and they're removed
in C2x
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13447
bcopy() has a confusing argument order and is actually a move, not a
copy; they're all deprecated since POSIX.1-2001 and removed in -2008,
and we shim them out to mem*() on Linux anyway
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12996
We recently had a case where our operators replaced a bad
multipathed disk, only to see it fail to autoreplace. The
zed logs showed that the multipath replacement disk did not pass
the 'is_dm' test in zfs_process_add() even though it should have.
is_dm is set if there exists a sysfs entry for to the
underlying /dev/sd* paths for the multipath disk. It's
possible this path didn't exist due to a race condition where
the sysfs paths weren't created at the time the udev event came
in to zed, but this was never verified.
This patch updates the check to look for udev properties that
indicate if the new autoreplace disk is an empty multipath disk,
rather than looking for the underlying sysfs entries. It also
adds in additional logging, and fixes a bug where zed allowed
you to use an already zfs-formatted disk from another pool
as a multipath auto-replacement disk.
Furthermore, while testing this patch, I also ran across a case
where a force-faulted disk did not have a ZPOOL_CONFIG_PHYS_PATH
entry in its config. This prevented it from being autoreplaced.
I added additional logic to derive the PHYS_PATH from the PATH if
the PATH was a /dev/disk/by-vdev/ path. For example, if PATH
was /dev/disk/by-vdev/L28, then PHYS_PATH would be L28. This is
safe since by-vdev paths represent physical locations and do not
change between boots.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#13023
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#12728
For kernel to send snapshot mount/unmount events to zed.
For kernel to send symlink creates/removes on zvol plumbing.
(/dev/run/dsk/zvol/$pool/$zvol -> /dev/diskX)
If zed misses the ENODEV, all errors after are EINVAL. Treat any error
as kernel module failure.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Closes#12416
This enables ZED to auto-online vdevs that are not wholedisk managed by
ZFS.
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Don Brady <don.brady@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
There are at least two interpretations of basename(3),
in addition to both functions being allowed to /both/ return a static
buffer (unsuitable in multi-threaded environments) /and/ raze the input
(which encourages overallocations, at best)
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12105
The pool guid and vdev guid received by zfs_agent_post_event(),
which calls zfs_retire_recv(), are normally non-zero. However,
later in this same method they may be unconditionally reset to
zero by the code which is intended to handle multipath, spare
and l2arc vdevs. This will result in the EC_dev_remove not
being handled.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>\
Co-authored-by: Vipin Kumar Verma <vipin.verma@hpe.com>
Signed-off-by: Srikanth N S <srikanth.nagasubbaraoseetharaman@hpe.com>
Closes#11564
In ZED zfs_retire agent added a check to handle Distributed Spare
replacement for Faulted VDEV also.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Vipin Kumar Verma <vipin.verma@hpe.com>
Signed-off-by: Mark Maybee <mark.maybee@hpe.com>
Closes#11354Closes#11355
This is needed for zfsd to autoreplace vdevs.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11260
This patch adds a new top-level vdev type called dRAID, which stands
for Distributed parity RAID. This pool configuration allows all dRAID
vdevs to participate when rebuilding to a distributed hot spare device.
This can substantially reduce the total time required to restore full
parity to pool with a failed device.
A dRAID pool can be created using the new top-level `draid` type.
Like `raidz`, the desired redundancy is specified after the type:
`draid[1,2,3]`. No additional information is required to create the
pool and reasonable default values will be chosen based on the number
of child vdevs in the dRAID vdev.
zpool create <pool> draid[1,2,3] <vdevs...>
Unlike raidz, additional optional dRAID configuration values can be
provided as part of the draid type as colon separated values. This
allows administrators to fully specify a layout for either performance
or capacity reasons. The supported options include:
zpool create <pool> \
draid[<parity>][:<data>d][:<children>c][:<spares>s] \
<vdevs...>
- draid[parity] - Parity level (default 1)
- draid[:<data>d] - Data devices per group (default 8)
- draid[:<children>c] - Expected number of child vdevs
- draid[:<spares>s] - Distributed hot spares (default 0)
Abbreviated example `zpool status` output for a 68 disk dRAID pool
with two distributed spares using special allocation classes.
```
pool: tank
state: ONLINE
config:
NAME STATE READ WRITE CKSUM
slag7 ONLINE 0 0 0
draid2:8d:68c:2s-0 ONLINE 0 0 0
L0 ONLINE 0 0 0
L1 ONLINE 0 0 0
...
U25 ONLINE 0 0 0
U26 ONLINE 0 0 0
spare-53 ONLINE 0 0 0
U27 ONLINE 0 0 0
draid2-0-0 ONLINE 0 0 0
U28 ONLINE 0 0 0
U29 ONLINE 0 0 0
...
U42 ONLINE 0 0 0
U43 ONLINE 0 0 0
special
mirror-1 ONLINE 0 0 0
L5 ONLINE 0 0 0
U5 ONLINE 0 0 0
mirror-2 ONLINE 0 0 0
L6 ONLINE 0 0 0
U6 ONLINE 0 0 0
spares
draid2-0-0 INUSE currently in use
draid2-0-1 AVAIL
```
When adding test coverage for the new dRAID vdev type the following
options were added to the ztest command. These options are leverages
by zloop.sh to test a wide range of dRAID configurations.
-K draid|raidz|random - kind of RAID to test
-D <value> - dRAID data drives per group
-S <value> - dRAID distributed hot spares
-R <value> - RAID parity (raidz or dRAID)
The zpool_create, zpool_import, redundancy, replacement and fault
test groups have all been updated provide test coverage for the
dRAID feature.
Co-authored-by: Isaac Huang <he.huang@intel.com>
Co-authored-by: Mark Maybee <mmaybee@cray.com>
Co-authored-by: Don Brady <don.brady@delphix.com>
Co-authored-by: Matthew Ahrens <mahrens@delphix.com>
Co-authored-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mark Maybee <mmaybee@cray.com>
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#10102
This change updates the documentation to refer to the project
as OpenZFS instead ZFS on Linux. Web links have been updated
to refer to https://github.com/openzfs/zfs. The extraneous
zfsonlinux.org web links in the ZED and SPL sources have been
dropped.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11007
Due to commit d48091d a removed device is now explicitly offlined by
the ZED if no spare is available, rather than the letting ZFS detect
it as UNAVAIL. This broke auto-replacing of whole-disk devices, as
described in issue #10577. In short, when a new device is reinserted
in the same slot, the ZED will try to ONLINE it without letting ZFS
recreate the necessary partition table.
This change simply avoids setting the device OFFLINE when removed if
no spare is available (or if spare_on_remove is false). This change
has been left minimal to allow it to be backported to 0.8.x release.
The auto_offline_001_pos ZTS test has been updated accordingly.
Some follow up work is planned to update the ZED so it transitions
the vdev to a REMOVED state. This is a state which has always
existed but there is no current interface the ZED can use to
accomplish this. Therefore it's being left to a follow up PR.
Reviewed-by: Gionatan Danti <g.danti@assyoma.it>
Co-authored-by: Gionatan Danti <g.danti@assyoma.it>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#10577Closes#10730
The device_rebuild feature enables sequential reconstruction when
resilvering. Mirror vdevs can be rebuilt in LBA order which may
more quickly restore redundancy depending on the pools average block
size, overall fragmentation and the performance characteristics
of the devices. However, block checksums cannot be verified
as part of the rebuild thus a scrub is automatically started after
the sequential resilver completes.
The new '-s' option has been added to the `zpool attach` and
`zpool replace` command to request sequential reconstruction
instead of healing reconstruction when resilvering.
zpool attach -s <pool> <existing vdev> <new vdev>
zpool replace -s <pool> <old vdev> <new vdev>
The `zpool status` output has been updated to report the progress
of sequential resilvering in the same way as healing resilvering.
The one notable difference is that multiple sequential resilvers
may be in progress as long as they're operating on different
top-level vdevs.
The `zpool wait -t resilver` command was extended to wait on
sequential resilvers. From this perspective they are no different
than healing resilvers.
Sequential resilvers cannot be supported for RAIDZ, but are
compatible with the dRAID feature being developed.
As part of this change the resilver_restart_* tests were moved
in to the functional/replacement directory. Additionally, the
replacement tests were renamed and extended to verify both
resilvering and rebuilding.
Original-patch-by: Isaac Huang <he.huang@intel.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: John Poduska <jpoduska@datto.com>
Co-authored-by: Mark Maybee <mmaybee@cray.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#10349
Mark functions used only in the same translation unit as static. This
only includes functions that do not have a prototype in a header file
either.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Closes#10470
Factor Linux specific functionality out of libzutil.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#9356
Factor Linux specific pieces out of libspl.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Sean Eric Fagan <sef@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9336
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Closes#9234
zed core dumps due to a NULL pointer in zfs_agent_iter_vdev(). The
gs_devid is NULL, but the nvl has a "devid" entry.
zfs_agent_post_event() checks that ZFS_EV_VDEV_GUID or DEV_IDENTIFIER is
present in nvl, but then later it and zfs_agent_iter_vdev() assume that
DEV_IDENTIFIER is present and thus gs_devid is set.
Typically this is not a problem because usually either all vdevs have
devid's, or none of them do. Since zfs_agent_iter_vdev() first checks if
the vdev has devid before dereferencing gs_devid, the problem isn't
typically encountered. However, if some vdevs have devid's and some do
not, then the problem is easily reproduced. This can happen if the pool
has been moved from a system that has devid's to one that does not.
The fix is for zfs_agent_iter_vdev() to only try to match the devid's if
both nvl and gsp have devid's present.
Reviewed-by: Prashanth Sreenivasa <pks@delphix.com>
Reviewed-by: Don Brady <don.brady@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
External-issue: DLPX-65090
Closes#9054Closes#9060
This commit adds a new test case to the ZFS Test Suite to verify ZED
can detect when a device is physically removed from a running system:
the device will be offlined if a spare is not available in the pool.
We implement this by using the existing libudev functionality and
without relying solely on the FM kernel module capabilities which have
been observed to be unreliable with some kernels.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Don Brady <don.brady@delphix.com>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#1537Closes#7926
Adds a libzutil for utility functions that are common to libzfs and
libzpool consumers (most of what was in libzfs_import.c). This
removes the need for utilities to link against both libzpool and
libzfs.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@delphix.com>
Closes#8050
The root cause of these failures is that udev can notify the
ZED of newly created partition before its links are created.
Handle this by allowing an auto-replace to briefly wait until
udev confirms the links exist.
Distill this test case down to its essentials so it can be run
reliably. What we need to check is that:
1) A new disk, in the same physical location, is automatically
brought online when added to the system,
2) It completes the replacement process, and
3) The pool is now ONLINE and healthy.
There is no need to remove the scsi_debug module. After exporting
the pool the disk can be zeroed, removed, and then re-added to the
system as a new disk.
Reviewed by: loli10K <ezomori.nozomu@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8051
While the autoexpand property may seem like a small feature it
depends on a significant amount of system infrastructure. Enough
of that infrastructure is now in place that with a few modifications
for Linux it can be supported.
Auto-expand works as follows; when a block device is modified
(re-sized, closed after being open r/w, etc) a change uevent is
generated for udev. The ZED, which is monitoring udev events,
passes the change event along to zfs_deliver_dle() if the disk
or partition contains a zfs_member as identified by blkid.
From here the device is matched against all imported pool vdevs
using the vdev_guid which was read from the label by blkid. If
a match is found the ZED reopens the pool vdev. This re-opening
is important because it allows the vdev to be briefly closed so
the disk partition table can be re-read. Otherwise, it wouldn't
be possible to report the maximum possible expansion size.
Finally, if the property autoexpand=on a vdev expansion will be
attempted. After performing some sanity checks on the disk to
verify that it is safe to expand, the primary partition (-part1)
will be expanded and the partition table updated. The partition
is then re-opened (again) to detect the updated size which allows
the new capacity to be used.
In order to make all of the above possible the following changes
were required:
* Updated the zpool_expand_001_pos and zpool_expand_003_pos tests.
These tests now create a pool which is layered on a loopback,
scsi_debug, and file vdev. This allows for testing of non-
partitioned block device (loopback), a partition block device
(scsi_debug), and a file which does not receive udev change
events. This provided for better test coverage, and by removing
the layering on ZFS volumes there issues surrounding layering
one pool on another are avoided.
* zpool_find_vdev_by_physpath() updated to accept a vdev guid.
This allows for matching by guid rather than path which is a
more reliable way for the ZED to reference a vdev.
* Fixed zfs_zevent_wait() signal handling which could result
in the ZED spinning when a signal was not handled.
* Removed vdev_disk_rrpart() functionality which can be abandoned
in favor of kernel provided blkdev_reread_part() function.
* Added a rwlock which is held as a writer while a disk is being
reopened. This is important to prevent errors from occurring
for any configuration related IOs which bypass the SCL_ZIO lock.
The zpool_reopen_007_pos.ksh test case was added to verify IO
error are never observed when reopening. This is not expected
to impact IO performance.
Additional fixes which aren't critical but were discovered and
resolved in the course of developing this functionality.
* Added PHYS_PATH="/dev/zvol/dataset" to the vdev configuration for
ZFS volumes. This is as good as a unique physical path, while the
volumes are not used in the test cases anymore for other reasons
this improvement was included.
Reviewed by: Richard Elling <Richard.Elling@RichardElling.com>
Signed-off-by: Sara Hartse <sara.hartse@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#120Closes#2437Closes#5771Closes#7366Closes#7582Closes#7629
Minimal changes required to integrate the SPL sources in to the
ZFS repository build infrastructure and packaging.
Build system and packaging:
* Renamed SPL_* autoconf m4 macros to ZFS_*.
* Removed redundant SPL_* autoconf m4 macros.
* Updated the RPM spec files to remove SPL package dependency.
* The zfs package obsoletes the spl package, and the zfs-kmod
package obsoletes the spl-kmod package.
* The zfs-kmod-devel* packages were updated to add compatibility
symlinks under /usr/src/spl-x.y.z until all dependent packages
can be updated. They will be removed in a future release.
* Updated copy-builtin script for in-kernel builds.
* Updated DKMS package to include the spl.ko.
* Updated stale AUTHORS file to include all contributors.
* Updated stale COPYRIGHT and included the SPL as an exception.
* Renamed README.markdown to README.md
* Renamed OPENSOLARIS.LICENSE to LICENSE.
* Renamed DISCLAIMER to NOTICE.
Required code changes:
* Removed redundant HAVE_SPL macro.
* Removed _BOOT from nvpairs since it doesn't apply for Linux.
* Initial header cleanup (removal of empty headers, refactoring).
* Remove SPL repository clone/build from zimport.sh.
* Use of DEFINE_RATELIMIT_STATE and DEFINE_SPINLOCK removed due
to build issues when forcing C99 compilation.
* Replaced legacy ACCESS_ONCE with READ_ONCE.
* Include needed headers for `current` and `EXPORT_SYMBOL`.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
TEST_ZIMPORT_SKIP="yes"
Closes#7556
Resolved unused variable warnings observed after restricting
-Wno-unused-but-set-variable to only libzfs and libzpool.
Reviewed-by: DHE <git@dehacked.net>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6941
