The current ZFS implementation stores xattrs on disk using a hidden
directory. In this directory a file name represents the xattr name
and the file contexts are the xattr binary data. This approach is
very flexible and allows for arbitrarily large xattrs. However,
it also suffers from a significant performance penalty. Accessing
a single xattr can requires up to three disk seeks.
1) Lookup the dnode object.
2) Lookup the dnodes's xattr directory object.
3) Lookup the xattr object in the directory.
To avoid this performance penalty Linux filesystems such as ext3
and xfs try to store the xattr as part of the inode on disk. When
the xattr is to large to store in the inode then a single external
block is allocated for them. In practice most xattrs are small
and this approach works well.
The addition of System Attributes (SA) to zfs provides us a clean
way to make this optimization. When the dataset property 'xattr=sa'
is set then xattrs will be preferentially stored as System Attributes.
This allows tiny xattrs (~100 bytes) to be stored with the dnode and
up to 64k of xattrs to be stored in the spill block. If additional
xattr space is required, which is unlikely under Linux, they will be
stored using the traditional directory approach.
This optimization results in roughly a 3x performance improvement
when accessing xattrs which brings zfs roughly to parity with ext4
and xfs (see table below). When multiple xattrs are stored per-file
the performance improvements are even greater because all of the
xattrs stored in the spill block will be cached.
However, by default SA based xattrs are disabled in the Linux port
to maximize compatibility with other implementations. If you do
enable SA based xattrs then they will not be visible on platforms
which do not support this feature.
----------------------------------------------------------------------
Time in seconds to get/set one xattr of N bytes on 100,000 files
------+--------------------------------+------------------------------
| setxattr | getxattr
bytes | ext4 xfs zfs-dir zfs-sa | ext4 xfs zfs-dir zfs-sa
------+--------------------------------+------------------------------
1 | 2.33 31.88 21.50 4.57 | 2.35 2.64 6.29 2.43
32 | 2.79 30.68 21.98 4.60 | 2.44 2.59 6.78 2.48
256 | 3.25 31.99 21.36 5.92 | 2.32 2.71 6.22 3.14
1024 | 3.30 32.61 22.83 8.45 | 2.40 2.79 6.24 3.27
4096 | 3.57 317.46 22.52 10.73 | 2.78 28.62 6.90 3.94
16384 | n/a 2342.39 34.30 19.20 | n/a 45.44 145.90 7.55
65536 | n/a 2941.39 128.15 131.32* | n/a 141.92 256.85 262.12*
Legend:
* ext4 - Stock RHEL6.1 ext4 mounted with '-o user_xattr'.
* xfs - Stock RHEL6.1 xfs mounted with default options.
* zfs-dir - Directory based xattrs only.
* zfs-sa - Prefer SAs but spill in to directories as needed, a
trailing * indicates overflow in to directories occured.
NOTE: Ext4 supports 4096 bytes of xattr name/value pairs per file.
NOTE: XFS and ZFS have no limit on xattr name/value pairs per file.
NOTE: Linux limits individual name/value pairs to 65536 bytes.
NOTE: All setattr/getattr's were done after dropping the cache.
NOTE: All tests were run against a single hard drive.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #443
Add a "REFRATIO" property, which is the compression ratio based on
data referenced. For snapshots, this is the same as COMPRESSRATIO,
but for filesystems/volumes, the COMPRESSRATIO is based on the
data "USED" (ie, includes blocks in children, but not blocks
shared with the origin).
This is needed to figure out how much space a filesystem would
use if it were not compressed (ignoring snapshots).
Reviewed by: George Wilson <George.Wilson@delphix.com>
Reviewed by: Adam Leventhal <Adam.Leventhal@delphix.com>
Reviewed by: Dan McDonald <danmcd@nexenta.com>
Reviewed by: Richard Elling <richard.elling@richardelling.com>
Reviewed by: Mark Musante <Mark.Musante@oracle.com>
Reviewed by: Garrett D'Amore <garrett@nexenta.com>
Approved by: Garrett D'Amore <garrett@nexenta.com>
References to Illumos issue and patch:
- https://www.illumos.org/issues/1092
- https://github.com/illumos/illumos-gate/commit/187d6ac08a
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #340
