Currently when the dataset is in use we can't receive snapshots.
zfs send test/1@asd | zfs recv -FM test/2
cannot unmount '/test/2': Device busy
This commits add option 'M' which attempts to forcibly unmount the
dataset. Thanks to this we can enforce receiving snapshots in a
single step.
Note that this functionality is not supported on Linux because the
VFS will prevent active mounted filesystems from being unmounted,
even with the force option. This is the intended VFS behavior.
Test cases were added to verify the expected behavior based on
the platform.
Discussed-with: Pawel Jakub Dawidek <pjd@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Allan Jude <allanjude@freebsd.org>
External-issue: https://reviews.freebsd.org/D22306Closes#9904
For each WRITE record in the stream, `zfs receive` creates a DMU
transaction (`dmu_tx_create()`) and writes this block's data into the
object. If per-block overheads (as opposed to per-byte overheads)
dominate performance (as is often the case with small recordsize), the
per-dmu-transaction overheads can be significant. For example, in some
workloads the `receieve_writer` thread is 100% on CPU, and more than
half of its CPU time is in these per-tx routines (e.g.
dmu_tx_hold_write, dmu_tx_assign, dmu_tx_commit).
To improve performance of `zfs receive`, this commit batches WRITE
records which are to nearby offsets of the same object, and uses one DMU
transaction to write them all. By default the batch size is 1MB, which
for recordsize=8K reduces the number of DMU transactions by 128x for
full send streams (incrementals will depend on how "clumpy" the changed
blocks are).
This commit improves the performance of `dd if=stream | zfs recv`
from 78,800 blocks/sec to 98,100 blocks/sec (25% improvement).
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#10099
Filesystems allow overlay mounts by default on FreeBSD and Linux.
Respect the native convention by switching the default to overlay=on,
while retaining the option to turn the property off for compatibility
with other operating systems' conventions.
Update documentation and tests accordingly.
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10030
Manual trims fall into the category of long-running pool activities
which people might want to wait synchronously for. This change adds
support to 'zpool wait' for waiting for manual trim operations to
complete. It also adds a '-w' flag to 'zpool trim' which can be used to
turn 'zpool trim' into a synchronous operation.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Signed-off-by: John Gallagher <john.gallagher@delphix.com>
Closes#10071
The Linux VFS will never allow a filesystem which is in use to
be unmounted. This behavior differs from other platforms like
FreeBSD which allow a filesystem to be force unmounted. This
will result in errors being returned to applications actively
using the filesystem.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Mariusz Zaborski <oshogbo@vexillium.org>
Closes#10013
Moving forward, we wish to use org.openzfs (no dash) rather than
org.open-zfs or org.zfsonlinux for feature GUIDs and property names.
The existing feature GUIDs cannot be changed.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Richard Laager <rlaager@wiktel.com>
Closes#10003
This commit refactors the systemd mount generators and makes the
following major changes:
- The generator now generates units for datasets marked canmount=noauto,
too. These units are NOT WantedBy local-fs.target.
If there are multiple noauto datasets for a path, no noauto unit will
be created. Datasets with canmount=on are prioritized.
- Introduces handling of new user properties which are now included in
the zfs-list.cache files:
- org.openzfs.systemd:requires:
List of units to require for this mount unit
- org.openzfs.systemd:requires-mounts-for:
List of mounts to require by this mount unit
- org.openzfs.systemd:before:
List of units to order after this mount unit
- org.openzfs.systemd:after:
List of units to order before this mount unit
- org.openzfs.systemd:wanted-by:
List of units to add a Wants dependency on this mount unit to
- org.openzfs.systemd:required-by:
List of units to add a Requires dependency on this mount unit to
- org.openzfs.systemd:nofail:
Toggles between a wants and a requires dependency.
- org.openzfs.systemd:ignore:
Do not generate a mount unit for this dataset.
Consult the updated man page for detailed documentation.
- Restructures and extends the zfs-mount-generator(8) man page with the
above properties, information on unit ordering and a license header.
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Antonio Russo <antonio.e.russo@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: InsanePrawn <insane.prawny@gmail.com>
Closes#9649
This adds support for setting user properties in a
zfs channel program by adding 'zfs.sync.set_prop'
and 'zfs.check.set_prop' to the ZFS LUA API.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Ahrens <matt@delphix.com>
Co-authored-by: Sara Hartse <sara.hartse@delphix.com>
Contributions-by: Jason King <jason.king@joyent.com>
Signed-off-by: Sara Hartse <sara.hartse@delphix.com>
Signed-off-by: Jason King <jason.king@joyent.com>
Closes#9950
The module parameter zfs_async_block_max_blocks limits the number of
blocks that can be freed by the background freeing of filesystems and
snapshots (from "zfs destroy"), in one TXG. This is useful when freeing
dedup blocks, becuase each zio_free() of a dedup block can require an
i/o to read the relevant part of the dedup table (DDT), and will also
dirty that block.
zfs_async_block_max_blocks is set to 100,000 by default. For the more
typical case where dedup is not used, this can have a negative
performance impact on the rate of background freeing (from "zfs
destroy"). For example, with recordsize=8k, and TXG's syncing once
every 5 seconds, we can free only 160MB of data per second, which may be
much less than the rate we can write data.
This change increases zfs_async_block_max_blocks to be unlimited by
default. To address the dedup freeing issue, a new tunable is
introduced, zfs_max_async_dedup_frees, which limits the number of
zio_free()'s of dedup blocks done by background destroys, per txg. The
default is 100,000 free's (same as the old zfs_async_block_max_blocks
default).
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#10000
Add support for bookmark creation and cloning.
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Christian Schwarz <me@cschwarz.com>
Closes#9571
This feature allows copying existing bookmarks using
zfs bookmark fs#target fs#newbookmark
There are some niche use cases for such functionality,
e.g. when using bookmarks as markers for replication progress.
Copying redaction bookmarks produces a normal bookmark that
cannot be used for redacted send (we are not duplicating
the redaction object).
ZCP support for bookmarking (both creation and copying) will be
implemented in a separate patch based on this work.
Overview:
- Terminology:
- source = existing snapshot or bookmark
- new/bmark = new bookmark
- Implement bookmark copying in `dsl_bookmark.c`
- create new bookmark node
- copy source's `zbn_phys` to new's `zbn_phys`
- zero-out redaction object id in copy
- Extend existing bookmark ioctl nvlist schema to accept
bookmarks as sources
- => `dsl_bookmark_create_nvl_validate` is authoritative
- use `dsl_dataset_is_before` check for both snapshot
and bookmark sources
- Adjust CLI
- refactor shortname expansion logic in `zfs_do_bookmark`
- Update man pages
- warn about redaction bookmark handling
- Add test cases
- CLI
- pyyzfs libzfs_core bindings
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Christian Schwarz <me@cschwarz.com>
Closes#9571
zdb -R :b fails due to the indirect block being compressed,
and the 'b' and 'd' flag not working in tandem when specified.
Fix the flag parsing code and create a zfs test for zdb -R
block display. Also fix the zio flags where the dotted notation
for the vdev portion of DVA (i.e. 0.0:offset:length) fails.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Zuchowski <pzuchowski@datto.com>
Closes#9640Closes#9729
Currently SIMD accelerated AES-GCM performance is limited by two
factors:
a. The need to disable preemption and interrupts and save the FPU
state before using it and to do the reverse when done. Due to the
way the code is organized (see (b) below) we have to pay this price
twice for each 16 byte GCM block processed.
b. Most processing is done in C, operating on single GCM blocks.
The use of SIMD instructions is limited to the AES encryption of the
counter block (AES-NI) and the Galois multiplication (PCLMULQDQ).
This leads to the FPU not being fully utilized for crypto
operations.
To solve (a) we do crypto processing in larger chunks while owning
the FPU. An `icp_gcm_avx_chunk_size` module parameter was introduced
to make this chunk size tweakable. It defaults to 32 KiB. This step
alone roughly doubles performance. (b) is tackled by porting and
using the highly optimized openssl AES-GCM assembler routines, which
do all the processing (CTR, AES, GMULT) in a single routine. Both
steps together result in up to 32x reduction of the time spend in
the en/decryption routines, leading up to approximately 12x
throughput increase for large (128 KiB) blocks.
Lastly, this commit changes the default encryption algorithm from
AES-CCM to AES-GCM when setting the `encryption=on` property.
Reviewed-By: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-By: Jason King <jason.king@joyent.com>
Reviewed-By: Tom Caputi <tcaputi@datto.com>
Reviewed-By: Richard Laager <rlaager@wiktel.com>
Signed-off-by: Attila Fülöp <attila@fueloep.org>
Closes#9749
This replaces the placeholder ZFS_PROP_PRIVATE with ZFS_PROP_ACLMODE,
matching what is done in the NFSv4 ACLs PR (#9709).
On FreeBSD we hide ZFS_PROP_ACLTYPE, while on Linux we hide
ZFS_PROP_ACLMODE.
The tests already assume this arrangement.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#9913
Allow a range of object identifiers to dump with -d. This may
be useful when dumping a large dataset and you want to break
it up into multiple phases, or to resume where a previous scan
left off. Object type selection flags are supported to reduce
the performance overhead of verbosely dumping unwanted objects,
and to reduce the amount of post-processing work needed to
filter out unwanted objects from zdb output.
This change extends existing syntax in a backward-compatible
way. That is, the base case of a range is to specify a single
object identifier to dump. Ranges and object identifiers can
be intermixed as command line parameters.
Usage synopsis:
Object ranges take the form <start>:<end>[:<flags>]
start Starting object number
end Ending object number, or -1 for no upper bound
flags Optional flags to select object types:
A All objects (this is the default)
d ZFS directories
f ZFS files
m SPA space maps
z ZAPs
- Negate effect of next flag
Examples:
# Dump all file objects
zdb -dd tank/fish 0👎f
# Dump all file and directory objects
zdb -dd tank/fish 0👎fd
# Dump all types except file and directory objects
zdb -dd tank/fish 0👎A-f-d
# Dump object IDs in a specific range
zdb -dd tank/fish 1000:2000
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Paul Zuchowski <pzuchowski@datto.com>
Signed-off-by: Ned Bass <bass6@llnl.gov>
Closes#9832
Implements the RAID-Z function using AltiVec SIMD.
This is basically the NEON code translated to AltiVec.
Note that the 'fletcher' algorithm requires 64-bits
operations, and the initial implementations of AltiVec
(PPC74xx a.k.a. G4, PPC970 a.k.a. G5) only has up to
32-bits operations, so no 'fletcher'.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Romain Dolbeau <romain.dolbeau@european-processor-initiative.eu>
Closes#9539
This adds support in channel programs to inherit properties analogous
to `zfs inherit` by adding `zfs.sync.inherit` and `zfs.check.inherit`
functions to the ZFS LUA API.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jason King <jason.king@joyent.com>
Closes#9738
As an alternative to the dataset name, zdb now allows the decimal
or hexadecimal objset ID to be specified. When permanent errors
are reported as 2 hexadecimal numbers (objset ID : object ID) in
zpool status; you can now use 'zdb <pool>[/objset ID] object' to
determine the names of the objset and object which have the error.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Paul Zuchowski <pzuchowski@datto.com>
Closes#9733
As discussed on the 2019-01-07 OpenZFS Leadership Meeting, we need to be
clear about the limitations of `zfs change-key`. Changing the user key
does not change the master key, nor does it currently overwrite the old
wrapped master key on disk.
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Garrett Fields <ghfields@gmail.com>
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Signed-off-by: Richard Laager <rlaager@wiktel.com>
Closes#9819
Update the project website links contained in to repository to
reference the secure https://zfsonlinux.org address.
Reviewed-By: Richard Laager <rlaager@wiktel.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Garrett Fields <ghfields@gmail.com>
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9837
This commit adds the --saved (-S) to the 'zfs send' command.
This flag allows a user to send a partially received dataset,
which can be useful when migrating a backup server to new
hardware. This flag is compatible with resumable receives, so
even if the saved send is interrupted, it can be resumed.
The flag does not require any user / kernel ABI changes or any
new feature flags in the send stream format.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Alek Pinchuk <apinchuk@datto.com>
Reviewed-by: Paul Zuchowski <pzuchowski@datto.com>
Reviewed-by: Christian Schwarz <me@cschwarz.com>
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#9007
I ran a report against the output of `modinfo zfs.ko`. This commit adds
everything missing and corrects a few renamed module parameters.
Specifically:
* zfs_checksums_per second renamed in ad796b8a3
* vdev_ms_count_limit renamed in c853f382d
Also fixes some variable type inconsistencies (unsigned int => uint)
Reviewed-by: George Amanakis <gamanakis@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: DHE <git@dehacked.net>
Closes#9809
The corresponding zpool status option is -P and not -p. Update
this description to reference the correct option.
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9803
If the ZFS_COLOR env variable is set, then use ANSI color
output in zpool status:
- Column headers are bold
- Degraded or offline pools/vdevs are yellow
- Non-zero error counters and faulted vdevs/pools are red
- The 'status:' and 'action:' sections are yellow if they're
displaying a warning.
This also includes a new 'faketty' function in libtest.shlib that is
compatible with FreeBSD (code provided by @freqlabs).
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#9340
Add the 'zfs jail/unjail' subcommands along with the relevant
documentation from FreeBSD. This feature is not supported on
Linux and still requires the match kernel ioctls which will
be included when the FreeBSD platform code is integrated.
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#9686
This interferes with zdb_read_block trying all the decompression
algorithms when the 'd' flag is specified, as some are
expected to fail. Also control the output when guessing
algorithms, try the more common compression types first, allow
specifying lsize/psize, and fix an uninitialized variable.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Zuchowski <pzuchowski@datto.com>
Closes#9612Closes#9630
FreeBSD uses its own crypto framework in-kernel which, at this time,
has no EDONR implementation.
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Allan Jude <allanjude@freebsd.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#9664
There may be circumstances where it's desirable that all blocks
in a specified dataset be stored on the special device. Relax
the artificial 128K limit and allow the special_small_blocks
property to be set up to 1M. When blocks >1MB have been enabled
via the zfs_max_recordsize module option, this limit is increased
accordingly.
Reviewed-by: Don Brady <don.brady@delphix.com>
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9131Closes#9355
As described in commit f81d5ef6 the zfs_vdev_elevator module
option is being removed. Users who require this functionality
should update their systems to set the disk scheduler using a
udev rule.
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #8664Closes#9417Closes#9609
The function zdb_read_block (zdb -R) was always intended to have a :c
flag which would read the DVA and length supplied by the user, and
display the checksum. Since we don't know which checksum goes with
the data, we should calculate and display them all.
For each checksum in the table, read in the data at the supplied
DVA:length, calculate the checksum, and display it. Update the man
page and create a zfs test for the new feature.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Signed-off-by: Paul Zuchowski <pzuchowski@datto.com>
Closes#9607
zed.service does not exist
replaced with correct service name in man.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Kjeld Schouten-Lebbing <kjeld@schouten-lebbing.nl>
Closes#9581
Moved subcommand topics into individual manpages. Reordered and
grouped the list of subcommands by topic.
Moved concepts overview to `zpoolconcepts.8` and the long list of
available pool properties to `zpoolprops.8`.
Internal cross-references copied from `zpool.8` needed to be
converted to `.Xr` external references to new subcommand manual
pages.
Move `autotrim` into lexical order, autotrim tacked onto the end
of a list. Now it is in alphabetical order.
Clarify attach/detach description. Description was too specific to
command syntax. Overview clarifies reason for attaching or detaching
a device.
Clarify replace description, don't refer to subcommand arguments.
Clarify split command description, say what split actually does and
why you'd want to do it.
Clarify description of upgrade, and simplify the zpool.8 wording of
the zpool-upgrade(8) description.
Clarify description of import, detail what zpool-import(8) actually
does.
Add appropriate SEE ALSO sections. Divided zpool subcommand manual
pages need their own SEE ALSO sections. Also modified fsck.zfs.8
to point directly to zfs-scrub.8 and zed.8.in to include a direct
reference to zfs-events.8
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ross Williams <ross@ross-williams.net>
Closes#9564
Most subcommands got their own manpages (e.g. create). Some related
commands grouped into a single manpage and symlinks created (e.g. set,
get, and inherit). I did this when topics were either too short to
warrant their own file or so interrelated that a user would want to
refer between commands in the same file.
Corrected .Sx internal references to .Xr cross refs; lots of .Sx
references from when text was all in zfs.8 needed to be changed to
.Xr zfs-$SUBCOMMAND 8 cross references.
Divided subcommand list in zfs(8) into sections of related
functionality. This required writing new descriptions for some
commands.
Preserved ".Os Linux", `.Os` macro parsing behavior differs between
mandoc from the "BSD" mandoc package (available on Ubuntu) and man
from Ubuntu's man-db package, which calls groff to format the manpages.
Groff handles the `.Os` macro differently and wrongly, defaulting
it to "BSD" in `/usr/share/groff/*/tmac/mdoc/doc-common`, instead of
getting the default from `uname`.
A future set of changes will introduce build-time preprocessing of
manpages for platform-specific documentation and can insert the
correct operating system name.
Added SEE ALSO sections, the newly-divided zfs-*.8 subcommand man
pages needed their own SEE ALSO sections pointing to related
subcommands and, in some cases, documentation from other packages
(e.g. zfs-share.8).
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Reviewed-by: Sean Eric Fagan <sef@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ross Williams <ross@ross-williams.net>
Closes#9559
It is much faster than AVX512F when byteswapping on Skylake-SP
and newer, as we can do the byteswap in a single vshufb instead
of many instructions.
Reviewed by: Gvozden Neskovic <neskovic@gmail.com>
Reviewed-by: Chunwei Chen <tuxoko@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Romain Dolbeau <romain.dolbeau@atos.net>
Closes#9517
While it may sometimes be convenient to export an NFS filesystem with
no_root_squash it should not be the default behavior. Align the
default behavior with the Linux NFS server defaults. To restore
the previous behavior use 'zfs set sharenfs="no_root_squash,..."'.
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9397Closes#9425
Since 0.7.0, zpool import would unconditionally block on udev for 30
seconds. This introduced a regression in initramfs environments that
lack udev (particularly mdev based environments), yet use a zfs userland
tools intended for the system that had been built against udev. Gentoo's
genkernel is the main example, although custom user initramfs
environments would be similarly impacted unless special builds of the
ZFS userland utilities were done for them. Such environments already
have their own mechanisms for blocking until device nodes are ready
(such as genkernel's scandelay parameter), so it is unnecessary for
zpool import to block on a non-existent udev until a timeout is reached
inside of them.
Rather than trying to intelligently determine whether udev is available
on the system to avoid unnecessarily blocking in such environments, it
seems best to just allow the environment to override the timeout. I
propose that we add an environment variable called
ZPOOL_IMPORT_UDEV_TIMEOUT_MS. Setting it to 0 would restore the 0.6.x
behavior that was more desirable in mdev based initramfs environments.
This allows the system user land utilities to be reused when building
mdev-based initramfs archives.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Georgy Yakovlev <gyakovlev@gentoo.org>
Signed-off-by: Richard Yao <ryao@gentoo.org>
Closes#9436
Update the zfs(8) man page to clearly describe that arguments for
channel programs are to be listed after the -- sentinel which
terminates argument processing. This behavior is supported by
getopt on Linux, FreeBSD, and Illumos according to each platforms
respective man pages.
zfs program [-jn] [-t instruction-limit] [-m memory-limit]
pool script [--] arg1 ...
Reviewed-by: Clint Armstrong <clint@clintarmstrong.net>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9056Closes#9428
Originally the zfs_vdev_elevator module option was added as a
convenience so the requested elevator would be automatically set
on the underlying block devices. At the time this was simple
because the kernel provided an API function which did exactly this.
This API was then removed in the Linux 4.12 kernel which prompted
us to add compatibly code to set the elevator via a usermodehelper.
While well intentioned this introduced a bug which could cause a
system hang, that issue was subsequently fixed by commit 2a0d4188.
In order to avoid future bugs in this area, and to simplify the code,
this functionality is being deprecated. A console warning has been
added to notify any existing consumers and the documentation updated
accordingly. This option will remain for the lifetime of the 0.8.x
series for compatibility but if planned to be phased out of master.
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #8664Closes#9317
Currently the best way to wait for the completion of a long-running
operation in a pool, like a scrub or device removal, is to poll 'zpool
status' and parse its output, which is neither efficient nor convenient.
This change adds a 'wait' subcommand to the zpool command. When invoked,
'zpool wait' will block until a specified type of background activity
completes. Currently, this subcommand can wait for any of the following:
- Scrubs or resilvers to complete
- Devices to initialized
- Devices to be replaced
- Devices to be removed
- Checkpoints to be discarded
- Background freeing to complete
For example, a scrub that is in progress could be waited for by running
zpool wait -t scrub <pool>
This also adds a -w flag to the attach, checkpoint, initialize, replace,
remove, and scrub subcommands. When used, this flag makes the operations
kicked off by these subcommands synchronous instead of asynchronous.
This functionality is implemented using a new ioctl. The type of
activity to wait for is provided as input to the ioctl, and the ioctl
blocks until all activity of that type has completed. An ioctl was used
over other methods of kernel-userspace communiction primarily for the
sake of portability.
Porting Notes:
This is ported from Delphix OS change DLPX-44432. The following changes
were made while porting:
- Added ZoL-style ioctl input declaration.
- Reorganized error handling in zpool_initialize in libzfs to integrate
better with changes made for TRIM support.
- Fixed check for whether a checkpoint discard is in progress.
Previously it also waited if the pool had a checkpoint, instead of
just if a checkpoint was being discarded.
- Exposed zfs_initialize_chunk_size as a ZoL-style tunable.
- Updated more existing tests to make use of new 'zpool wait'
functionality, tests that don't exist in Delphix OS.
- Used existing ZoL tunable zfs_scan_suspend_progress, together with
zinject, in place of a new tunable zfs_scan_max_blks_per_txg.
- Added support for a non-integral interval argument to zpool wait.
Future work:
ZoL has support for trimming devices, which Delphix OS does not. In the
future, 'zpool wait' could be extended to add the ability to wait for
trim operations to complete.
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: John Gallagher <john.gallagher@delphix.com>
Closes#9162
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Closes#9233
With the other metaslab changes loaded onto a system, we can
significantly reduce the memory usage of each loaded metaslab and
unload them on demand if there is memory pressure. However, none
of those changes actually result in us keeping more metaslabs loaded.
If we don't keep more metaslabs loaded, we will still have to wait
for demand-loading to finish when no loaded metaslab can satisfy our
allocation, which can cause ZIL performance issues. In addition,
performance is traditionally measured by IOs per unit time, while
unloading is currently done on a txg-count basis. Txgs can take a
widely varying range of times, from tenths of a second to several
seconds. This can result in confusing, hard to predict behavior.
This change simply adds a time-based component to metaslab unloading.
A metaslab will remain loaded for one minute and 8 txgs (by default)
after it was last used, unless it is evicted due to memory pressure.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
External-issue: DLPX-65016
External-issue: DLPX-65047
Closes#9197
On systems with large amounts of storage and high fragmentation, a huge
amount of space can be used by storing metaslab range trees. Since
metaslabs are only unloaded during a txg sync, and only if they have
been inactive for 8 txgs, it is possible to get into a state where all
of the system's memory is consumed by range trees and metaslabs, and
txgs cannot sync. While ZFS knows how to evict ARC data when needed,
it has no such mechanism for range tree data. This can result in boot
hangs for some system configurations.
First, we add the ability to unload metaslabs outside of syncing
context. Second, we store a multilist of all loaded metaslabs, sorted
by their selection txg, so we can quickly identify the oldest
metaslabs. We use a multilist to reduce lock contention during heavy
write workloads. Finally, we add logic that will unload a metaslab
when we're loading a new metaslab, if we're using more than a certain
fraction of the available memory on range trees.
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Sebastien Roy <sebastien.roy@delphix.com>
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#9128
When a pool is imported it will scan the pool to verify the integrity
of the data and metadata. The amount it scans will depend on the
import flags provided. On systems with small amounts of memory or
when importing a pool from the crash kernel, it's possible for
spa_load_verify to issue too many I/Os that it consumes all the memory
of the system resulting in an OOM message or a hang.
To prevent this, we limit the amount of memory that the initial pool
scan can consume. This change will, by default, use 1/16th of the ARC
for scan I/Os to prevent running the system out of memory during import.
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Signed-off-by: George Wilson george.wilson@delphix.com
External-issue: DLPX-65237
External-issue: DLPX-65238
Closes#9146
Consumers of ZFS Channel Programs can now list bookmarks,
and get holds from datasets. A minor-refactoring was also
applied to distinguish between user and system properties
in ZCP.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Ported-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Signed-off-by: Dan Kimmel <dan.kimmel@delphix.com>
OpenZFS-issue: https://illumos.org/issues/8862Closes#7902
When we unload metaslabs today in ZFS, the cached max_size value is
discarded. We instead use the histogram to determine whether or not we
think we can satisfy an allocation from the metaslab. This can result in
situations where, if we're doing I/Os of a size not aligned to a
histogram bucket, a metaslab is loaded even though it cannot satisfy the
allocation we think it can. For example, a metaslab with 16 entries in
the 16k-32k bucket may have entirely 16kB entries. If we try to allocate
a 24kB buffer, we will load that metaslab because we think it should be
able to handle the allocation. Doing so is expensive in CPU time, disk
reads, and average IO latency. This is exacerbated if the write being
attempted is a sync write.
This change makes ZFS cache the max_size after the metaslab is
unloaded. If we ever get a free (or a coalesced group of frees) larger
than the max_size, we will update it. Otherwise, we leave it as is. When
attempting to allocate, we use the max_size as a lower bound, and
respect it unless we are in try_hard. However, we do age the max_size
out at some point, since we expect the actual max_size to increase as we
do more frees. A more sophisticated algorithm here might be helpful, but
this works reasonably well.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#9055
Update zpool-features.5 manpage to describe the log_spacemap feature.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Signed-off-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Closes#9096
Deleting a clone requires finding blocks are clone-only, not shared
with the snapshot. This was done by traversing the entire block tree
which results in a large performance penalty for sparsely
written clones.
This is new method keeps track of clone blocks when they are
modified in a "Livelist" so that, when it’s time to delete,
the clone-specific blocks are already at hand.
We see performance improvements because now deletion work is
proportional to the number of clone-modified blocks, not the size
of the original dataset.
Reviewed-by: Sean Eric Fagan <sef@ixsystems.com>
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Signed-off-by: Sara Hartse <sara.hartse@delphix.com>
Closes#8416
The zfs-volume-wait.service scans existing zvols and waits for their
links under /dev to be created. Any service that depends on zvol
links to be there should add a dependency on zfs-volumes.target.
By default, this target is not enabled.
Reviewed-by: Fabian Grünbichler <f.gruenbichler@proxmox.com>
Reviewed-by: Antonio Russo <antonio.e.russo@gmail.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: John Gallagher <john.gallagher@delphix.com>
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Pavel Zakharov <pzakharov@delphix.com>
Closes#8975
Adds the ability to sanity check zfs create arguments and to see the
value of any additional properties that will local to the dataset. For
example, automation that may need to adjust quota on a parent filesystem
before creating a volume may call `zfs create -nP -V <size> <volume>` to
obtain the value of refreservation. This adds the following options to
zfs create:
- -n dry-run (no-op)
- -v verbose
- -P parseable (implies verbose)
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Jerry Jelinek <jerry.jelinek@joyent.com>
Signed-off-by: Mike Gerdts <mike.gerdts@joyent.com>
Closes#8974
= Motivation
At Delphix we've seen a lot of customer systems where fragmentation
is over 75% and random writes take a performance hit because a lot
of time is spend on I/Os that update on-disk space accounting metadata.
Specifically, we seen cases where 20% to 40% of sync time is spend
after sync pass 1 and ~30% of the I/Os on the system is spent updating
spacemaps.
The problem is that these pools have existed long enough that we've
touched almost every metaslab at least once, and random writes
scatter frees across all metaslabs every TXG, thus appending to
their spacemaps and resulting in many I/Os. To give an example,
assuming that every VDEV has 200 metaslabs and our writes fit within
a single spacemap block (generally 4K) we have 200 I/Os. Then if we
assume 2 levels of indirection, we need 400 additional I/Os and
since we are talking about metadata for which we keep 2 extra copies
for redundancy we need to triple that number, leading to a total of
1800 I/Os per VDEV every TXG.
We could try and decrease the number of metaslabs so we have less
I/Os per TXG but then each metaslab would cover a wider range on
disk and thus would take more time to be loaded in memory from disk.
In addition, after it's loaded, it's range tree would consume more
memory.
Another idea would be to just increase the spacemap block size
which would allow us to fit more entries within an I/O block
resulting in fewer I/Os per metaslab and a speedup in loading time.
The problem is still that we don't deal with the number of I/Os
going up as the number of metaslabs is increasing and the fact
is that we generally write a lot to a few metaslabs and a little
to the rest of them. Thus, just increasing the block size would
actually waste bandwidth because we won't be utilizing our bigger
block size.
= About this patch
This patch introduces the Log Spacemap project which provides the
solution to the above problem while taking into account all the
aforementioned tradeoffs. The details on how it achieves that can
be found in the references sections below and in the code (see
Big Theory Statement in spa_log_spacemap.c).
Even though the change is fairly constraint within the metaslab
and lower-level SPA codepaths, there is a side-change that is
user-facing. The change is that VDEV IDs from VDEV holes will no
longer be reused. To give some background and reasoning for this,
when a log device is removed and its VDEV structure was replaced
with a hole (or was compacted; if at the end of the vdev array),
its vdev_id could be reused by devices added after that. Now
with the pool-wide space maps recording the vdev ID, this behavior
can cause problems (e.g. is this entry referring to a segment in
the new vdev or the removed log?). Thus, to simplify things the
ID reuse behavior is gone and now vdev IDs for top-level vdevs
are truly unique within a pool.
= Testing
The illumos implementation of this feature has been used internally
for a year and has been in production for ~6 months. For this patch
specifically there don't seem to be any regressions introduced to
ZTS and I have been running zloop for a week without any related
problems.
= Performance Analysis (Linux Specific)
All performance results and analysis for illumos can be found in
the links of the references. Redoing the same experiments in Linux
gave similar results. Below are the specifics of the Linux run.
After the pool reached stable state the percentage of the time
spent in pass 1 per TXG was 64% on average for the stock bits
while the log spacemap bits stayed at 95% during the experiment
(graph: sdimitro.github.io/img/linux-lsm/PercOfSyncInPassOne.png).
Sync times per TXG were 37.6 seconds on average for the stock
bits and 22.7 seconds for the log spacemap bits (related graph:
sdimitro.github.io/img/linux-lsm/SyncTimePerTXG.png). As a result
the log spacemap bits were able to push more TXGs, which is also
the reason why all graphs quantified per TXG have more entries for
the log spacemap bits.
Another interesting aspect in terms of txg syncs is that the stock
bits had 22% of their TXGs reach sync pass 7, 55% reach sync pass 8,
and 20% reach 9. The log space map bits reached sync pass 4 in 79%
of their TXGs, sync pass 7 in 19%, and sync pass 8 at 1%. This
emphasizes the fact that not only we spend less time on metadata
but we also iterate less times to convergence in spa_sync() dirtying
objects.
[related graphs:
stock- sdimitro.github.io/img/linux-lsm/NumberOfPassesPerTXGStock.png
lsm- sdimitro.github.io/img/linux-lsm/NumberOfPassesPerTXGLSM.png]
Finally, the improvement in IOPs that the userland gains from the
change is approximately 40%. There is a consistent win in IOPS as
you can see from the graphs below but the absolute amount of
improvement that the log spacemap gives varies within each minute
interval.
sdimitro.github.io/img/linux-lsm/StockVsLog3Days.png
sdimitro.github.io/img/linux-lsm/StockVsLog10Hours.png
= Porting to Other Platforms
For people that want to port this commit to other platforms below
is a list of ZoL commits that this patch depends on:
Make zdb results for checkpoint tests consistent
db587941c5
Update vdev_is_spacemap_addressable() for new spacemap encoding
419ba59145
Simplify spa_sync by breaking it up to smaller functions
8dc2197b7b
Factor metaslab_load_wait() in metaslab_load()
b194fab0fb
Rename range_tree_verify to range_tree_verify_not_present
df72b8bebe
Change target size of metaslabs from 256GB to 16GB
c853f382db
zdb -L should skip leak detection altogether
21e7cf5da8
vs_alloc can underflow in L2ARC vdevs
7558997d2f
Simplify log vdev removal code
6c926f426a
Get rid of space_map_update() for ms_synced_length
425d3237ee
Introduce auxiliary metaslab histograms
928e8ad47d
Error path in metaslab_load_impl() forgets to drop ms_sync_lock
8eef997679
= References
Background, Motivation, and Internals of the Feature
- OpenZFS 2017 Presentation:
youtu.be/jj2IxRkl5bQ
- Slides:
slideshare.net/SerapheimNikolaosDim/zfs-log-spacemaps-project
Flushing Algorithm Internals & Performance Results
(Illumos Specific)
- Blogpost:
sdimitro.github.io/post/zfs-lsm-flushing/
- OpenZFS 2018 Presentation:
youtu.be/x6D2dHRjkxw
- Slides:
slideshare.net/SerapheimNikolaosDim/zfs-log-spacemap-flushing-algorithm
Upstream Delphix Issues:
DLPX-51539, DLPX-59659, DLPX-57783, DLPX-61438, DLPX-41227, DLPX-59320
DLPX-63385
Reviewed-by: Sean Eric Fagan <sef@ixsystems.com>
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Closes#8442
Modify zfs-mount-generator to produce a dependency on new
zfs-import-key-*.service units, dynamically created at boot to call
zfs load-key for the encryption root, before attempting to mount any
encrypted datasets.
These units are created by zfs-mount-generator, and RequiresMountsFor on
the keyfile, if present, or call systemd-ask-password if a passphrase is
requested.
This patch includes suggestions from @Fabian-Gruenbichler, @ryanjaeb and
@rlaager, as well an adaptation of @rlaager's script to retry on
incorrect password entry.
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Fabian Grünbichler <f.gruenbichler@proxmox.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Antonio Russo <antonio.e.russo@gmail.com>
Closes#8750Closes#8848
* zfs redact error messages do not end with newline character
* 30af21b0 inadvertently removed some ZFS_PROP comments
* man/zfs: zfs redact <redaction_snapshot> is not optional
Reviewed-by: Giuseppe Di Natale <guss80@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#8988
The full property name includes "delphix", not "delphxi".
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#8985
This was accidentally introduced in 765d1f06:
mandoc: ./man/man8/zfs.8: ERROR: skipping item outside list: It Ar filesystem Ns | Ns Ar mountpoint
mandoc: ./man/man8/zfs.8: ERROR: skipping item outside list: It Xo
mandoc: ./man/man8/zfs.8: ERROR: skipping end of block that is not open: Xc
mandoc: ./man/man8/zfs.8: ERROR: skipping item outside list: It Xo
mandoc: ./man/man8/zfs.8: ERROR: skipping end of block that is not open: Xc
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#8980
This patch adds the ability for the user to unload keys for
datasets as they are being unmounted. This is analogous to
'zfs mount -l'.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alek Pinchuk <apinchuk@datto.com>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes: #8917Closes: #8952
If dedup is in use, the `dedupditto` property can be set, causing ZFS to
keep an extra copy of data that is referenced many times (>100x). The
idea was that this data is more important than other data and thus we
want to be really sure that it is not lost if the disk experiences a
small amount of random corruption.
ZFS (and system administrators) rely on the pool-level redundancy to
protect their data (e.g. mirroring or RAIDZ). Since the user/sysadmin
doesn't have control over what data will be offered extra redundancy by
dedupditto, this extra redundancy is not very useful. The bulk of the
data is still vulnerable to loss based on the pool-level redundancy.
For example, if particle strikes corrupt 0.1% of blocks, you will either
be saved by mirror/raidz, or you will be sad. This is true even if
dedupditto saved another 0.01% of blocks from being corrupted.
Therefore, the dedupditto functionality is rarely enabled (i.e. the
property is rarely set), and it fulfills its promise of increased
redundancy even more rarely.
Additionally, this feature does not work as advertised (on existing
releases), because scrub/resilver did not repair the extra (dedupditto)
copy (see https://github.com/zfsonlinux/zfs/pull/8270).
In summary, this seldom-used feature doesn't work, and even if it did it
wouldn't provide useful data protection. It has a non-trivial
maintenance burden (again see https://github.com/zfsonlinux/zfs/pull/8270).
We should remove the dedupditto functionality. For backwards
compatibility with the existing CLI, "zpool set dedupditto" will still
"succeed" (exit code zero), but won't have any effect. For backwards
compatibility with existing pools that had dedupditto enabled at some
point, the code will still be able to understand dedupditto blocks and
free them when appropriate. However, ZFS won't write any new dedupditto
blocks.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Alek Pinchuk <apinchuk@datto.com>
Issue #8270Closes#8310
Redacted send/receive allows users to send subsets of their data to
a target system. One possible use case for this feature is to not
transmit sensitive information to a data warehousing, test/dev, or
analytics environment. Another is to save space by not replicating
unimportant data within a given dataset, for example in backup tools
like zrepl.
Redacted send/receive is a three-stage process. First, a clone (or
clones) is made of the snapshot to be sent to the target. In this
clone (or clones), all unnecessary or unwanted data is removed or
modified. This clone is then snapshotted to create the "redaction
snapshot" (or snapshots). Second, the new zfs redact command is used
to create a redaction bookmark. The redaction bookmark stores the
list of blocks in a snapshot that were modified by the redaction
snapshot(s). Finally, the redaction bookmark is passed as a parameter
to zfs send. When sending to the snapshot that was redacted, the
redaction bookmark is used to filter out blocks that contain sensitive
or unwanted information, and those blocks are not included in the send
stream. When sending from the redaction bookmark, the blocks it
contains are considered as candidate blocks in addition to those
blocks in the destination snapshot that were modified since the
creation_txg of the redaction bookmark. This step is necessary to
allow the target to rehydrate data in the case where some blocks are
accidentally or unnecessarily modified in the redaction snapshot.
The changes to bookmarks to enable fast space estimation involve
adding deadlists to bookmarks. There is also logic to manage the
life cycles of these deadlists.
The new size estimation process operates in cases where previously
an accurate estimate could not be provided. In those cases, a send
is performed where no data blocks are read, reducing the runtime
significantly and providing a byte-accurate size estimate.
Reviewed-by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: Prashanth Sreenivasa <pks@delphix.com>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: George Wilson <george.wilson@delphix.com>
Reviewed-by: Chris Williamson <chris.williamson@delphix.com>
Reviewed-by: Pavel Zhakarov <pavel.zakharov@delphix.com>
Reviewed-by: Sebastien Roy <sebastien.roy@delphix.com>
Reviewed-by: Prakash Surya <prakash.surya@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#7958
If the zfs_remove_max_segment tunable is changed to be not a multiple of
the sector size, then the device removal code will malfunction and try
to create mappings that are smaller than one sector, leading to a panic.
On debug bits this assertion will fail in spa_vdev_copy_segment():
ASSERT3U(DVA_GET_ASIZE(&dst), ==, size);
On nondebug, the system panics with a stack like:
metaslab_free_concrete()
metaslab_free_impl()
metaslab_free_impl_cb()
vdev_indirect_remap()
free_from_removing_vdev()
metaslab_free_impl()
metaslab_free_dva()
metaslab_free()
Fortunately, the default for zfs_remove_max_segment is 1MB, so this
can't occur by default. We hit it during this test because
removal_remap.ksh changes zfs_remove_max_segment to 1KB. When testing on
4KB-sector disks, we hit the bug.
This change makes the zfs_remove_max_segment tunable more robust,
automatically rounding it up to a multiple of the sector size. We also
turn some key assertions into VERIFY's so that similar bugs would be
caught before they are encoded on disk (and thus avoid a
panic-reboot-loop).
Reviewed-by: Sean Eric Fagan <sef@ixsystems.com>
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: Sebastien Roy <sebastien.roy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
External-issue: DLPX-61342
Closes#8893
Starting in sync pass 5 (zfs_sync_pass_dont_compress), we disable
compression (including of metadata). Ostensibly this helps the sync
passes to converge (i.e. for a sync pass to not need to allocate
anything because it is 100% overwrites).
However, in practice it increases the average number of sync passes,
because when we turn compression off, a lot of block's size will change
and thus we have to re-allocate (not overwrite) them. It also increases
the number of 128KB allocations (e.g. for indirect blocks and spacemaps)
because these will not be compressed. The 128K allocations are
especially detrimental to performance on highly fragmented systems,
which may have very few free segments of this size, and may need to load
new metaslabs to satisfy 128K allocations.
We should increase zfs_sync_pass_dont_compress. In practice on a highly
fragmented system we see a few 5-pass txg's, a tiny number of 6-pass
txg's, and no txg's with more than 6 passes.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: George Wilson <george.wilson@delphix.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
External-issue: DLPX-63431
Closes#8892
On fragmented pools with high-performance storage, the looping in
metaslab_block_picker() can become the performance-limiting bottleneck.
When looking for a larger block (e.g. a 128K block for the ZIL), we may
search through many free segments (up to hundreds of thousands) to find
one that is large enough to satisfy the allocation. This can take a long
time (up to dozens of ms), and is done while holding the ms_lock, which
other threads may spin waiting for.
When this performance problem is encountered, profiling will show
high CPU time in metaslab_block_picker, as well as in mutex_enter from
various callers.
The problem is very evident on a test system with a sync write workload
with 8K writes to a recordsize=8k filesystem, with 4TB of SSD storage,
84% full and 88% fragmented. It has also been observed on production
systems with 90TB of storage, 76% full and 87% fragmented.
The fix is to change metaslab_df_alloc() to search only up to 16MB from
the previous allocation (of this alignment). After that, we will pick a
segment that is of the exact size requested (or larger). This reduces
the number of iterations to a few hundred on fragmented pools (a ~100x
improvement).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: George Wilson <george.wilson@delphix.com>
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
External-issue: DLPX-62324
Closes#8877
When iterating over a ZAP object, we're almost always certain to iterate
over the entire object. If there are multiple leaf blocks, we can
realize a performance win by issuing reads for all the leaf blocks in
parallel when the iteration begins.
For example, if we have 10,000 snapshots, "zfs destroy -nv
pool/fs@1%9999" can take 30 minutes when the cache is cold. This change
provides a >3x performance improvement, by issuing the reads for all ~64
blocks of each ZAP object in parallel.
Reviewed-by: Andreas Dilger <andreas.dilger@whamcloud.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
External-issue: DLPX-58347
Closes#8862
We've observed that on some highly fragmented pools, most metaslab
allocations are small (~2-8KB), but there are some large, 128K
allocations. The large allocations are for ZIL blocks. If there is a
lot of fragmentation, the large allocations can be hard to satisfy.
The most common impact of this is that we need to check (and thus load)
lots of metaslabs from the ZIL allocation code path, causing sync writes
to wait for metaslabs to load, which can take a second or more. In the
worst case, we may not be able to satisfy the allocation, in which case
the ZIL will resort to txg_wait_synced() to ensure the change is on
disk.
To provide a workaround for this, this change adds a tunable that can
reduce the size of ZIL blocks.
External-issue: DLPX-61719
Reviewed-by: George Wilson <george.wilson@delphix.com>
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#8865
Historically while doing performance testing we've noticed that IOPS
can be significantly reduced when all vdevs in the pool are hitting
the zfs_mg_fragmentation_threshold percentage. Specifically in a
hypothetical pool with two vdevs, what can happen is the following:
Vdev A would go above that threshold and only vdev B would be used.
Then vdev B would pass that threshold but vdev A would go below it
(we've been freeing from A to allocate to B). The allocations would
go back and forth utilizing one vdev at a time with IOPS taking a hit.
Empirically, we've seen that our vdev selection for allocations is
good enough that fragmentation increases uniformly across all vdevs
the majority of the time. Thus we set the threshold percentage high
enough to avoid hitting the speed bump on pools that are being pushed
to the edge. We effectively disable its effect in the majority of the
cases but we don't remove (at least for now) just in case we hit any
weird behavior in the future.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Signed-off-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Closes#8859
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Chris Dunlop <chris@onthe.net.au>
Signed-off-by: Peter Wirdemo <peter.wirdemo@gmail.com>
Closes#8855
Various changes (many by me) have been made to the man pages without
bumping their dates. I have now corrected them based on the last commit
to each file. I also added the script I used to make these changes.
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Laager <rlaager@wiktel.com>
Closes#8710
Exported and documented a new module parameter.
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: DHE <git@dehacked.net>
Closes#8706
When receiving a DRR_OBJECT record the receive_object() function
needs to determine how to handle a spill block associated with the
object. It may need to be removed or kept depending on how the
object was modified at the source.
This determination is currently accomplished using a heuristic which
takes in to account the DRR_OBJECT record and the existing object
properties. This is a problem because there isn't quite enough
information available to do the right thing under all circumstances.
For example, when only the block size changes the spill block is
removed when it should be kept.
What's needed to resolve this is an additional flag in the DRR_OBJECT
which indicates if the object being received references a spill block.
The DRR_OBJECT_SPILL flag was added for this purpose. When set then
the object references a spill block and it must be kept. Either
it is update to date, or it will be replaced by a subsequent DRR_SPILL
record. Conversely, if the object being received doesn't reference
a spill block then any existing spill block should always be removed.
Since previous versions of ZFS do not understand this new flag
additional DRR_SPILL records will be inserted in to the stream.
This has the advantage of being fully backward compatible. Existing
ZFS systems receiving this stream will recreate the spill block if
it was incorrectly removed. Updated ZFS versions will correctly
ignore the additional spill blocks which can be identified by
checking for the DRR_SPILL_UNMODIFIED flag.
The small downside to this approach is that is may increase the size
of the stream and of the received snapshot on previous versions of
ZFS. Additionally, when receiving streams generated by previous
unpatched versions of ZFS spill blocks may still be lost.
OpenZFS-issue: https://www.illumos.org/issues/9952
FreeBSD-issue: https://bugs.freebsd.org/bugzilla/show_bug.cgi?id=233277
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8668
This standardizes the language on "deduplication tables" rather than
"dedup data" (which might be read as the data blocks rather than the
DDT). Likewise, it standardizes on "small file blocks". It also
standardizes on "normal" rather than using both "normal" and "general"
in the same paragraph. I also replaced "non-specified" with the more
explicit "non-dedup/special".
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Laager <rlaager@wiktel.com>
Closes#8713
Authored by: Jason King <jason.king@joyent.com>
Reviewed by: Toomas Soome <tsoome@me.com>
Reviewed by: Andy Fiddaman <andy@omniosce.org>
Reviewed by: Peter Tribble <peter.tribble@gmail.com>
Reviewed by: Gergő Mihály Doma <domag02@gmail.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Dan McDonald <danmcd@joyent.com>
Ported-by: Richard Laager <rlaager@wiktel.com>
OpenZFS-issue: https://www.illumos.org/issues/10473
OpenZFS-commit: https://github.com/illumos/illumos-gate/commit/736e67003Closes#8711
The 'zpool resilver' command requires that the resilver_defer
feature is active on the pool. Unfortunately, the check for
this was left out of the original patch. This commit simply
corrects this so that the command properly returns an error
in this case.
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#8700
Currently, it is possible for the 'zpool scrub' command to
progress slightly beyond 100% due to concurrent changes
happening on the live pool. This behavior is expected, but
the userspace code for 'zpool status' would subtract the
expected amount of data from the amount of data already
scrubbed, resulting in a negative integer being casted to a
large positive one. This number was then used to calculate
the estimated completion time, resulting in wildly wrong
results. This code changes the behavior so that 'zpool status'
does not attempt to report an estimate during this period.
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#8611Closes#8687
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: Richard Laager <rlaager@wiktel.com>
Closes#8691
- Remove the language that "all user data" is encrypted. This is to
avoid misunderstandings or arguments about what is "user data",
especially in light of "user properties".
- Document that properties are unencrypted.
- Document that snapshot names are unencrypted.
- For consistency with the rest of the zfs.8 man page, use "ZFS" as the
generic noun, not (bolded) "zfs". The latter refers to the command.
Likewise, use "ZFS" instead of "the kernel module".
- Give "a passphrase" as an example of a "user's key".
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Richard Laager <rlaager@wiktel.com>
Closes#8652
This adds the encryption copies=3 limitation language into the copies
property section.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Laager <rlaager@wiktel.com>
Closes#8651
This documents, in zpool.8, that dedupditto is deprecated and will be
made to have no effect in a future release.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Richard Laager <rlaager@wiktel.com>
Closes#8650
As far as I know and can tell from testing, \fB\fB...\fR\fR is exactly
equivalent to \fB...\fR.
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Laager <rlaager@wiktel.com>
Closes#8641
The features are sorted in the en_US locale, not the C locale.
Specifically, that means that bookmark_v2 comes _after_ bookmarks.
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Laager <rlaager@wiktel.com>
Closes#8641
This command is being used to unindent, so it should be at the end of
each block. This is consistent with the other man pages.
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Laager <rlaager@wiktel.com>
Closes#8641
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Laager <rlaager@wiktel.com>
Closes#8641
It is org.open-zfs:large_blocks (plural).
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Laager <rlaager@wiktel.com>
Closes#8641
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Laager <rlaager@wiktel.com>
Closes#8641
The first sentence of this commit comes from the wiki, and was
originally written by:
Rich Ercolani <rincebrain@gmail.com>
with changes by:
Tom Caputi <tcaputi@datto.com>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Laager <rlaager@wiktel.com>
Closes#8641Closes#8642
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Laager <rlaager@wiktel.com>
Closes#8641
encryption depends on bookmark_v2.
bookmark_v2 depends on bookmarks.
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Laager <rlaager@wiktel.com>
Closes#8641
This needs to use tabs instead of spaces to display correctly (i.e. with
things lined up).
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Laager <rlaager@wiktel.com>
Closes#8641
It should only affect "zpool".
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@gmail.com>
Closes#8644
1. Support QAT when ZFS is root file-system:
When ZFS module is loaded before QAT started, the QAT can
be started again in post-process, e.g.:
echo 0 > /sys/module/zfs/parameters/zfs_qat_compress_disable
echo 0 > /sys/module/zfs/parameters/zfs_qat_encrypt_disable
echo 0 > /sys/module/zfs/parameters/zfs_qat_checksum_disable
2. Verify alder checksum of the de-compress result
3. Allocate Digest, IV and AAD buffer in physical contiguous
memory by QAT_PHYS_CONTIG_ALLOC.
4. Update the documentation for zfs_qat_compress_disable,
zfs_qat_checksum_disable, zfs_qat_encrypt_disable.
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Weigang Li <weigang.li@intel.com>
Signed-off-by: Chengfeix Zhu <chengfeix.zhu@intel.com>
Closes#8323Closes#8610
Add the 'zfs version' and 'zpool version' subcommands to display
the version of the user space utilities and loaded zfs kernel
module. For example:
$ zfs version
zfs-0.8.0-rc3_169_g67e0366b88
zfs-kmod-0.8.0-rc3_169_g67e0366b88
The '-V' and '--version' aliases were added to support the
common convention of using 'zfs --version` to obtain the version
information.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Signed-off-by: TerraTech <1118433+TerraTech@users.noreply.github.com>
Closes#2501Closes#8567
When creating a non-sparse volume, zfs create sets a refreservation.
Accordingly, one needs the "refreservation" ability in addition to the
"create" ability in order to create a non-sparse volume.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reported-by: github.com/homerlinux
Reported-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Richard Laager <rlaager@wiktel.com>
Closes#8531Closes#8624
zfs.8 correctly said that GRUB did not support them, but
zpool-features.5 said that "Booting off pools...is supported." Now,
zpool-features.5 discusses GRUB specifically and indicates its lack of
support for these features. Also, I have clarified the wording in both
places to indicate that the pool feature cannot be used. It's not a
filesystem dataset thing, but pool-wide.
I described this as "cannot be used". I think technically the feature
can be enabled, just not active. However, the effect is essentially the
same: you cannot enable those checksum algorithms on any dataset in the
pool, so you might as well not enable the feature (which is just
pointing a loaded gun at your foot). In the past, an argument could be
made that having all the features enabled was useful for simplicity, as
long as you didn't activate the GRUB-incompatible features, but that's
getting less and less realistic over time. A user can still do that,
but we should not encourage that.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Laager <rlaager@wiktel.com>
Closes#8626Closes#8446
The old wording was effectively "You can not use this (except you can)",
which just seems confusing.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Laager <rlaager@wiktel.com>
Closes#8626
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Laager <rlaager@wiktel.com>
Closes#8626
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Laager <rlaager@wiktel.com>
Closes#8626
On Linux, this is in man section 8, not 1M. Also, there is no fsdb on
Linux, so I removed that.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Laager <rlaager@wiktel.com>
Closes#8626
This had a mix of command vs subcommand, quoted vs not quoted, and
bolded vs. not bolded command names.
Also, fix man page sections from 1M (Solaris) to 8 (Linux).
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Laager <rlaager@wiktel.com>
Closes#8626
Previously, the "spare" vdev type was described as "A special
pseudo-vdev which...". I wanted to eliminate the word "special" from
that, now that the allocation_classes feature exists and there is such a
thing as a "special vdev". I ended up eliminating almost all instances
of the word "special" that are not referencing the allocation_classes
feature.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Laager <rlaager@wiktel.com>
Closes#8626
The macOS man app strenuously objects to blank lines in man files.
mdoc warning: Empty input line #xyz
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: bunder2015 <omfgbunder@gmail.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Josh Soref <jsoref@users.noreply.github.com>
Closes#8559
This patch simply clarifies some of the limitations related to
raw sends in the man page. No functional changes.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Jason Cohen <jwittlincohen@gmail.com>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#8503Closes#8544
UNMAP/TRIM support is a frequently-requested feature to help
prevent performance from degrading on SSDs and on various other
SAN-like storage back-ends. By issuing UNMAP/TRIM commands for
sectors which are no longer allocated the underlying device can
often more efficiently manage itself.
This TRIM implementation is modeled on the `zpool initialize`
feature which writes a pattern to all unallocated space in the
pool. The new `zpool trim` command uses the same vdev_xlate()
code to calculate what sectors are unallocated, the same per-
vdev TRIM thread model and locking, and the same basic CLI for
a consistent user experience. The core difference is that
instead of writing a pattern it will issue UNMAP/TRIM commands
for those extents.
The zio pipeline was updated to accommodate this by adding a new
ZIO_TYPE_TRIM type and associated spa taskq. This new type makes
is straight forward to add the platform specific TRIM/UNMAP calls
to vdev_disk.c and vdev_file.c. These new ZIO_TYPE_TRIM zios are
handled largely the same way as ZIO_TYPE_READs or ZIO_TYPE_WRITEs.
This makes it possible to largely avoid changing the pipieline,
one exception is that TRIM zio's may exceed the 16M block size
limit since they contain no data.
In addition to the manual `zpool trim` command, a background
automatic TRIM was added and is controlled by the 'autotrim'
property. It relies on the exact same infrastructure as the
manual TRIM. However, instead of relying on the extents in a
metaslab's ms_allocatable range tree, a ms_trim tree is kept
per metaslab. When 'autotrim=on', ranges added back to the
ms_allocatable tree are also added to the ms_free tree. The
ms_free tree is then periodically consumed by an autotrim
thread which systematically walks a top level vdev's metaslabs.
Since the automatic TRIM will skip ranges it considers too small
there is value in occasionally running a full `zpool trim`. This
may occur when the freed blocks are small and not enough time
was allowed to aggregate them. An automatic TRIM and a manual
`zpool trim` may be run concurrently, in which case the automatic
TRIM will yield to the manual TRIM.
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: George Wilson <george.wilson@delphix.com>
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Contributions-by: Saso Kiselkov <saso.kiselkov@nexenta.com>
Contributions-by: Tim Chase <tim@chase2k.com>
Contributions-by: Chunwei Chen <tuxoko@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8419Closes#598
When Multihost is enabled, and a pool is imported, uberblock writes
include ub_mmp_delay to allow an importing node to calculate the
duration of an activity test. This value, is not enough information.
If zfs_multihost_fail_intervals > 0 on the node with the pool imported,
the safe minimum duration of the activity test is well defined, but does
not depend on ub_mmp_delay:
zfs_multihost_fail_intervals * zfs_multihost_interval
and if zfs_multihost_fail_intervals == 0 on that node, there is no such
well defined safe duration, but the importing host cannot tell whether
mmp_delay is high due to I/O delays, or due to a very large
zfs_multihost_interval setting on the host which last imported the pool.
As a result, it may use a far longer period for the activity test than
is necessary.
This patch renames ub_mmp_sequence to ub_mmp_config and uses it to
record the zfs_multihost_interval and zfs_multihost_fail_intervals
values, as well as the mmp sequence. This allows a shorter activity
test duration to be calculated by the importing host in most situations.
These values are also added to the multihost_history kstat records.
It calculates the activity test duration differently depending on
whether the new fields are present or not; for importing pools with
only ub_mmp_delay, it uses
(zfs_multihost_interval + ub_mmp_delay) * zfs_multihost_import_intervals
Which results in an activity test duration less sensitive to the leaf
count.
In addition, it makes a few other improvements:
* It updates the "sequence" part of ub_mmp_config when MMP writes
in between syncs occur. This allows an importing host to detect MMP
on the remote host sooner, when the pool is idle, as it is not limited
to the granularity of ub_timestamp (1 second).
* It issues writes immediately when zfs_multihost_interval is changed
so remote hosts see the updated value as soon as possible.
* It fixes a bug where setting zfs_multihost_fail_intervals = 1 results
in immediate pool suspension.
* Update tests to verify activity check duration is based on recorded
tunable values, not tunable values on importing host.
* Update tests to verify the expected number of uberblocks have valid
MMP fields - fail_intervals, mmp_interval, mmp_seq (sequence number),
that sequence number is incrementing, and that uberblock values match
tunable settings.
Reviewed-by: Andreas Dilger <andreas.dilger@whamcloud.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#7842
Currently, there is an issue in the sequential scrub code which
prevents self healing from working in some cases. The scrub code
will split up all DVA copies of a bp and issue each of them
separately. The problem is that, since each of the DVAs is no
longer associated with the others, the self healing code doesn't
have the opportunity to repair problems that show up in one of the
DVAs with the data from the others.
This patch fixes this issue by ensuring that all IOs issued by the
sequential scrub code include all DVAs. Initially, only the first
DVA of each is attempted. If an issue arises, the IO is retried
with all available copies, giving the self healing code a chance
to correct the issue.
To test this change, this patch also adds the ability for zinject
to specify individual DVAs to inject read errors into. We then
add a new test case that utilizes this functionality to ensure
scrubs and self-healing reads can handle and transparently fix
issues with individual copies of blocks.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#8453
Before sequential scrub patches ZFS never aggregated I/Os above 128KB.
Sequential scrub bumped that to 1MB, supposedly to reduce number of
head seeks for spinning disks. But for SSDs it makes little to no
sense, especially on FreeBSD, where due to MAXPHYS limitation device
will likely still see bunch of 128KB I/Os instead of one large.
Having more strict aggregation limit for SSDs allows to avoid
allocation of large memory buffer and copy to/from it, that is a
serious problem when throughput reaches gigabytes per second.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#8494
Currently, there is an issue in the raw receive code where
raw receives are allowed to happen on top of previously
non-raw received datasets. This is a problem because the
source-side dataset doesn't know about how the blocks on
the destination were encrypted. As a result, any MAC in
the objset's checksum-of-MACs tree that is a parent of both
blocks encrypted on the source and blocks encrypted by the
destination will be incorrect. This will result in
authentication errors when we decrypt the dataset.
This patch fixes this issue by adding a new check to the
raw receive code. The code now maintains an "IVset guid",
which acts as an identifier for the set of IVs used to
encrypt a given snapshot. When a snapshot is raw received,
the destination snapshot will take this value from the
DRR_BEGIN payload. Non-raw receives and normal "zfs snap"
operations will cause ZFS to generate a new IVset guid.
When a raw incremental stream is received, ZFS will check
that the "from" IVset guid in the stream matches that of
the "from" destination snapshot. If they do not match, the
code will error out the receive, preventing the problem.
This patch requires an on-disk format change to add the
IVset guids to snapshots and bookmarks. As a result, this
patch has errata handling and a tunable to help affected
users resolve the issue with as little interruption as
possible.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#8308
This patch adds the bookmark v2 feature to the on-disk format. This
feature will be needed for the upcoming redacted sends and for an
upcoming fix that for raw receives. The feature is not currently
used by any code and thus this change is a no-op, aside from the
fact that the user can now enable the feature.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Issue #8308
By default, when multihost is enabled for a pool, the pool is
suspended if (zfs_multihost_fail_intervals*zfs_multihost_interval) ms
pass without a successful MMP write. This is the recommended
configuration.
The default value for zfs_multihost_fail_intervals has been 5, and the
default value for zfs_multihost_interval has been 1000, so pool
suspension occurred at 5 seconds.
There have been multiple cases where a single misbehaving device in a
pool triggered a SCSI reset, and all I/O paused for 5-6 seconds. This
in turn caused MMP to suspend the pool.
In the cases observed, the rest of the devices were healthy and the
pool was otherwise correctly performing I/O. The reset was handled
correctly by ZFS, and by suspending the pool MMP made replacing the
device more difficult as well as forcing the host to be rebooted.
Increase the default value of zfs_multihost_fail_intervals to 10, so
that MMP tolerates up to 10 seconds of failed MMP writes before
suspending the pool.
Increase the default value of zfs_multihost_import_intervals to 20, to
maintain the 2:1 safety factor. This results in a force import taking
approximately 20 seconds when MMP is enabled, with default values.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Andreas Dilger <andreas.dilger@whamcloud.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#7709Closes#8495
When multihost is enabled, and a pool is suspended, return
EINVAL in response to "zpool clear <pool>". The pool
may have been imported on another host while I/O was suspended.
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#6933Closes#8460
Improve the man page text to warn the user about the risk of adding
the same device to multiple pools via simultaneous "zpool create",
"zpool add", "zpool replace", etc.
State that MMP/multihost does not protect against these scenarios.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#6473Closes#8457
abd_alloc() normally does scatter allocations, thus solving the problem
that ABD originally set out to: the bulk of ZFS's allocations are single
pages, which are faster to allocate and free, and don't suffer from
internal fragmentation (and the inability to reclaim memory because some
buffers in the slab are still allocated).
However, the current code does linear allocations for 4KB and smaller
allocations, defeating the purpose of ABD.
Scatter ABD's use at least one page each, so sub-page allocations waste
some space when allocated as scatter (e.g. 2KB scatter allocation wastes
half of each page). Using linear ABD's for small allocations means that
they will be put on slabs which contain many allocations. This can
improve memory efficiency, but it also makes it much harder for ARC
evictions to actually free pages, because all the buffers on one slab
need to be freed in order for the slab (and underlying pages) to be
freed. Typically, 512B and 1KB kmem caches have 16 buffers per slab, so
it's possible for them to actually waste more memory than scatter (one
page per buf = wasting 3/4 or 7/8th; one buf per slab = wasting
15/16th).
Spill blocks are typically 512B and are heavily used on systems running
selinux with the default dnode size and the `xattr=sa` property set.
By default we will use linear allocations for 512B and 1KB, and scatter
allocations for larger (1.5KB and up).
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: DHE <git@dehacked.net>
Reviewed-by: Chunwei Chen <tuxoko@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Don Brady <don.brady@delphix.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#8455
The "-t" argument to "zfs program" specifies a limit on the number of
LUA instructions that can be executed. The zfs.8 manpage has the wrong
description. It should be updated to match what's in zfs-program.8
Also fix the formatting of the zfs help message.
Reviewed by: Allan Jude <allanjude@freebsd.org>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#8410
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed by: Allan Jude <allanjude@freebsd.org>
Reviewed-by: bunder2015 <omfgbunder@gmail.com>
Signed-off-by: DHE <git@dehacked.net>
Closes#4660Closes#8423
In
-T u|d Display a time stamp. Specify -u for a printed
representation of the internal representation of time.
See time(2). Specify -d for standard date format.
See date(1).
'Specify u' and 'Specify d' should be used instead. `zpool list -T -u`
does not work.
Bring the descriptions in `zpool list` and `zpool status` in sync with
`zpool iostat`.
Reviewed by: Allan Jude <allanjude@freebsd.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Anatoly Borodin <anatoly.borodin@gmail.com>
Closes#8438
Add the zio_deadman_log_all tunable to print all zios in
zio_deadman_impl(). Also, in all cases, display the depth of the
zio relative to the original parent zio. This is meant to be used by
developers to gain diagnostic information for hangs which don't involve
fully set-up zio trees or are otherwise stuck or hung in an early stage.
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Signed-off-by: Tim Chase <tim@chase2k.com>
Closes#8362
Add -h switch to zfs send command to send dataset holds. If
holds are present in the stream, zfs receive will create them
on the target dataset, unless the zfs receive -h option is used
to skip receive of holds.
Reviewed-by: Alek Pinchuk <apinchuk@datto.com>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Signed-off-by: Paul Zuchowski <pzuchowski@datto.com>
Closes#7513
Deletion throttle currently does not account for holes in a file.
This means that it can activate when it shouldn't.
To fix it we switch the throttle to be based on the number of
L1 blocks we will have to dirty when freeing
Reviewed by: Tom Caputi <tcaputi@datto.com>
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alek Pinchuk <apinchuk@datto.com>
Closes#7725Closes#7888
This patch is an async implementation of the existing sync
zfs_unlinked_drain() function. This function is called at mount time and
is responsible for freeing znodes that we didn't get to freeing before.
We don't have to hold mounting of the dataset until the unlinked list is
fully drained as is done now. Since we can process the unlinked set
asynchronously this results in a better user experience when mounting a
dataset with entries in the unlinked set.
Reviewed by: Jorgen Lundman <lundman@lundman.net>
Reviewed by: Tom Caputi <tcaputi@datto.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Signed-off-by: Alek Pinchuk <apinchuk@datto.com>
Closes#8142
Due to an off-by-one condition in spa_preferred_class() we are picking
the "normal" allocation class instead of the "special" one for file
blocks with size equal to the special_small_blocks property value.
This change fix the small code issue, update the ZFS Test Suite and the
zfs(8) man page.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Don Brady <don.brady@delphix.com>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#8351Closes#8361
Currently the point of -L option in zdb is to disable leak
tracing and the loading of space maps because they are expensive,
yet still do leak detection in terms of space. Unfortunately,
there is a scenario where this is a lie. If we are using zdb -L
on a pool where a vdev is being removed, zdb_claim_removing()
will open the metaslab space maps of that device.
This patch makes it so zdb -L skips leak detection altogether
and ensures that no space maps are loaded.
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Closes#8335
= Old behavior
For vdev sizes 100GB to 50TB we keep ~200 metaslabs per
vdev and the metaslab size grows from 512MB to 256GB.
For vdev's bigger than that we start increasing the
number of metaslabs until we hit the 128K limit.
= New Behavior
For vdev sizes 100GB to 3TB we keep ~200 metaslabs per
vdev and the metaslab size grows from 512MB to 16GB.
For vdev's bigger than that we start increasing the
number of metaslabs until we hit the 128K limit.
= Reasoning
The old behavior makes metaslabs grow in size when
the vdev range is between 3TB (ms_size 16GB) and
32PB (ms_size 256GB). Even though keeping the number
of metaslabs is good in terms of potential number of
I/Os per TXG, these bigger metaslabs take longer
to be loaded and after they are loaded they can
take up a lot of memory because of their range trees.
This change tries to put a boundary in memory and
loading time for the specific range of vdev sizes.
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Don Brady <don.brady@delphix.com>
Signed-off-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Closes#8324
When `zpool iostat` fills the terminal the headers should be
printed again. `zpool iostat -n` can be used to suppress this.
If the command is not attached to a tty, headers will not be
printed so as to not break existing scripts.
Reviewed-by: Joshua M. Clulow <josh@sysmgr.org>
Reviewed-by: Giuseppe Di Natale <guss80@gmail.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Damian Wojsław <damian@wojslaw.pl>
Closes#8235Closes#8262
Increase the default allowed number of reconstruction attempts.
There's not an exact right number for this setting. It needs
to be set large enough to cover any realistic failure scenarios
and small enough to avoid stalling the IO pipeline and invoking
the dead man detection.
The current value of 256 was empirically determined to be too
low based on multi-day runs of ztest. The fault injection code
would inject more damage than could be reconstructed given the
relatively small number of attempts. However, in all observed
cases the block could be reconstructed using a slightly higher
limit.
Based on local testing increasing the default value to 4096 was
determined to strike the best balance. Checking all combinations
takes less than 10s in the worst case, and has so far eliminated
the vast majority of false positives detected by ztest. This
delay is roughly on par with how long retries may be performed
to a misbehaving HDD and was deemed to be reasonable. Better to
err on the side of a brief delay rather than fail to reconstruct
the data.
Lastly, the -Y flag has been added to zdb to make it easy to try all
possible combinations when performing split block reconstruction.
For badly damaged blocks with 18 splits, they can be fully enumerated
within a few minutes. This has been done to ensure permanent errors
are never incorrectly reported when ztest verifies the pool with zdb.
Reviewed by: Tom Caputi <tcaputi@datto.com>
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed by: Serapheim Dimitropoulos <serapheim@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8271
The implementation of 'zfs remap' has proven to be problematic since
it modifies the objset (but not its logical contents) by dirtying
metadata without owning it. The consequence of which is that
dmu_objset_remap_indirects() is vulnerable to certain races.
For example, if we are in the middle of receiving into the filesystem
while it is being remapped. Then it is possible we could evict the
objset when the receive completes (see dsl_dataset_clone_swap_sync_impl,
or dmu_recv_end_sync), but dmu_objset_remap_indirects() may be still
using the objset. The result of which would be a panic.
Extended runs of ztest(8) have exposed other possible races which
can occur when using 'zfs remap'. Several of these have been fixed
but there may be others which have not yet been encountered and
diagnosed.
Furthermore, the ability to manually remap a filesystem is no longer
particularly useful now that the removal code can map large chunks.
Coupled with the fact that explaining what this command does and why
it may be useful requires a detailed understanding of the internals
of device removal. These are details users should not be bothered
with.
Therefore, the 'zfs remap' command is being disabled but not entirely
removed. It may be removed in the future or potentially reworked
to address the issues described above. Since 'zfs remap' has never
been part of a tagged release its removal is expected to have
minimal impact.
The ZTS tests have been updated to continue to exercise the command
to prevent atrophy, but it has been removed entirely from ztest(8).
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8238
Only display the full details of the vdev initialization state
in 'zpool status' output when requested with the -i option.
By default display '(initializing)' after vdevs when they are
being actively initialized. This is consistent with the
established precident of appending '(resilvering), etc' and
fits within the default 80 column terminal width making it
easy to read.
Additionally, updated the 'zpool initialize' documentation to
make it clear the options are mutually exclusive, but allow
duplicate options like all other zfs/zpool commands.
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed-by: George Wilson <george.wilson@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8230
PROBLEM
========
The first access to a block incurs a performance penalty on some platforms
(e.g. AWS's EBS, VMware VMDKs). Therefore we recommend that volumes are
"thick provisioned", where supported by the platform (VMware). This can
create a large delay in getting a new virtual machines up and running (or
adding storage to an existing Engine). If the thick provision step is
omitted, write performance will be suboptimal until all blocks on the LUN
have been written.
SOLUTION
=========
This feature introduces a way to 'initialize' the disks at install or in the
background to make sure we don't incur this first read penalty.
When an entire LUN is added to ZFS, we make all space available immediately,
and allow ZFS to find unallocated space and zero it out. This works with
concurrent writes to arbitrary offsets, ensuring that we don't zero out
something that has been (or is in the middle of being) written. This scheme
can also be applied to existing pools (affecting only free regions on the
vdev). Detailed design:
- new subcommand:zpool initialize [-cs] <pool> [<vdev> ...]
- start, suspend, or cancel initialization
- Creates new open-context thread for each vdev
- Thread iterates through all metaslabs in this vdev
- Each metaslab:
- select a metaslab
- load the metaslab
- mark the metaslab as being zeroed
- walk all free ranges within that metaslab and translate
them to ranges on the leaf vdev
- issue a "zeroing" I/O on the leaf vdev that corresponds to
a free range on the metaslab we're working on
- continue until all free ranges for this metaslab have been
"zeroed"
- reset/unmark the metaslab being zeroed
- if more metaslabs exist, then repeat above tasks.
- if no more metaslabs, then we're done.
- progress for the initialization is stored on-disk in the vdev’s
leaf zap object. The following information is stored:
- the last offset that has been initialized
- the state of the initialization process (i.e. active,
suspended, or canceled)
- the start time for the initialization
- progress is reported via the zpool status command and shows
information for each of the vdevs that are initializing
Porting notes:
- Added zfs_initialize_value module parameter to set the pattern
written by "zpool initialize".
- Added zfs_vdev_{initializing,removal}_{min,max}_active module options.
Authored by: George Wilson <george.wilson@delphix.com>
Reviewed by: John Wren Kennedy <john.kennedy@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: loli10K <ezomori.nozomu@gmail.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Richard Lowe <richlowe@richlowe.net>
Signed-off-by: Tim Chase <tim@chase2k.com>
Ported-by: Tim Chase <tim@chase2k.com>
OpenZFS-issue: https://www.illumos.org/issues/9102
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/c3963210ebCloses#8230
* Capitalize POSIX in POSIX ACLs. This change makes the POSIX
in POSIX ACLs all caps, which is both correct and consistent with
the rest of the man page.
* Slightly reword part of zfs.8. I tweaked a sentence to add a
missing comma, and as long as I was editing, removed a couple
unnecessary words.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: bunder2015 <omfgbunder@gmail.com>
Signed-off-by: Richard Laager <rlaager@wiktel.com>
Closes#8220
Add an 'enclosure_symlinks' option to vdev_id.conf. This creates
consistently named symlinks to the enclosure devices (/dev/sg*) based
off the configuration in vdev_id.conf. The enclosure symlinks show
up in /dev/by-enclosure/<prefix>-<channel><num>. The links make it
make it easy to run sg_ses on a particular enclosure device. The
enclosure links are created in addition to the normal
/dev/disk/by-vdev links.
'enclosure_symlinks' is only valid in sas_direct configurations.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Simon Guest <simon.guest@tesujimath.org>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#8194
Porting Notes:
* Add options to zfs-module-parameters(5) man page.
* zfs_nocacheflush move to vdev.c instead of vdev_disk.c, since
the latter doesn't get built for user space.
Authored by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: Matt Ahrens <matt@delphix.com>
Reviewed by: Brad Lewis <brad.lewis@delphix.com>
Reviewed by: Patrick Mooney <patrick.mooney@joyent.com>
Reviewed by: Tom Caputi <tcaputi@datto.com>
Reviewed by: George Melikov <mail@gmelikov.ru>
Approved by: Dan McDonald <danmcd@joyent.com>
Ported-by: Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/9963
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/f8fdf68125Closes#8186
* Detect IO errors during device removal
While device removal cannot verify the checksums of individual
blocks during device removal, it can reasonably detect hard IO
errors from the leaf vdevs. Failure to perform this error
checking can result in device removal completing successfully,
but moving no data which will permanently corrupt the pool.
Situation 1: faulted/degraded vdevs
In the configuration shown below, the removal of mirror-0 will
permanently corrupt the pool. Device removal will preferentially
copy data from 'vdev1 -> vdev3' and from 'vdev2 -> vdev4'. Which
in this case will result in nothing being copied since one vdev
in each of those groups in unavailable. However, device removal
will complete successfully since all IO errors are ignored.
tank DEGRADED 0 0 0
mirror-0 DEGRADED 0 0 0
/var/tmp/vdev1 FAULTED 0 0 0 external fault
/var/tmp/vdev2 ONLINE 0 0 0
mirror-1 DEGRADED 0 0 0
/var/tmp/vdev3 ONLINE 0 0 0
/var/tmp/vdev4 FAULTED 0 0 0 external fault
This issue is resolved by updating the source child selection
logic to exclude unreadable leaf vdevs. Additionally, unwritable
destination child vdevs which can never succeed are skipped to
prevent generating a large number of write IO errors.
Situation 2: individual hard IO errors
During removal if an unexpected hard IO error is encountered when
either reading or writing the child vdev the entire removal
operation is cancelled. While it may be possible to reconstruct
the data after removal that cannot be guaranteed. The only
strictly safe thing to do is to cancel the removal.
As a future improvement we may want to instead suspend the removal
process and allow the damaged region to be retried. But that work
is left for another time, hard IO errors during the removal process
are expected to be exceptionally rare.
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #6900Closes#8161
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <guss80@gmail.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Signed-off-by: Christian Schwarz <me@cschwarz.com>
Closes#8134
This patch adds a new slow I/Os (-s) column to zpool status to show the
number of VDEV slow I/Os. This is the number of I/Os that didn't
complete in zio_slow_io_ms milliseconds. It also adds a new parsable
(-p) flag to display exact values.
NAME STATE READ WRITE CKSUM SLOW
testpool ONLINE 0 0 0 -
mirror-0 ONLINE 0 0 0 -
loop0 ONLINE 0 0 0 20
loop1 ONLINE 0 0 0 0
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#7756Closes#6885
Update zfs-events.5 with info from PSARC 2009/497 regarding ereport fields.
Also updates ZIO_STAGE_* and ZIO_FLAG_* descriptions to match current source.
Reviewed by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Elling <Richard.Elling@RichardElling.com>
Closes#8057
Currently, if a resilver is triggered for any reason while an
existing one is running, zfs will immediately restart the existing
resilver from the beginning to include the new drive. This causes
problems for system administrators when a drive fails while another
is already resilvering. In this case, the optimal thing to do to
reduce risk of data loss is to wait for the current resilver to end
before immediately replacing the second failed drive, which allows
the system to operate with two incomplete drives for the minimum
amount of time.
This patch introduces the resilver_defer feature that essentially
does this for the admin without forcing them to wait and monitor
the resilver manually. The change requires an on-disk feature
since we must mark drives that are part of a deferred resilver in
the vdev config to ensure that we do not assume they are done
resilvering when an existing resilver completes.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: @mmaybee
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#7732
Porting notes:
* Renamed zfs_dirty_data_sync_pct to zfs_dirty_data_sync_percent and
changed the type to be consistent with the other dirty module params.
* Updated zfs-module-parameters.5 accordingly.
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Serapheim Dimitropoulos <serapheim.dimitro@delphix.com>
Reviewed by: Brad Lewis <brad.lewis@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Andrew Stormont <andyjstormont@gmail.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Approved by: Robert Mustacchi <rm@joyent.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://illumos.org/issues/9617
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/7928f4baCloses#7976
Porting notes:
* Two of the three changes from the upstream patch were already
applied for Linux. Only the last one is required.
Authored by: Yuri Pankov <yuri.pankov@nexenta.com>
Reviewed by: Robert Mustacchi <rm@joyent.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Approved by: Gordon Ross <gwr@nexenta.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://illumos.org/issues/9763
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/8a702e55Closes#7972
Due to a flaw in 4589f3ae the number of unique combinations
could be calculated incorrectly. This could result in the
random combinations reconstruction being used when it would
have been possible to check all combinations.
This change fixes the unique combinations calculation and
simplifies the reconstruction logic by maintaining a per-
segment list of unique copies.
The vdev_indirect_splits_damage() function was introduced
to validate both the enumeration and random reconstruction
logic with ztest. It is implemented such it will never
make a known recoverable block unrecoverable.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #6900Closes#7934
Reviewed-by: Giuseppe Di Natale <guss80@gmail.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Signed-off-by: DHE <git@dehacked.net>
Closes#7938
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Signed-off-by: DHE <git@dehacked.net>
Closes#7920
The man pages for zpool and zfs (get command)
listed the pool/dataset parameter as required,
but these are optional. Fixed that.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Gregor Kopka <gregor@kopka.net>
Closes#7916
Update zpool(8) to clarify what type of vdevs may be safely
removed and that the existence of any top-level raidz device
which is part of the primary pool will prevent device removal.
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7880Closes#7893
When no permission set is defined for a dataset the create time
permissions are incorrectly shown as if they were a permission set.
This change simply correct how allow permissions are displayed.
This commit also fixes a small manpage formatting issue and adds the
"zfs_allow_003_pos" test case to the ZFS Test Suite.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#7519Closes#7860
Allocation Classes add the ability to have allocation classes in a
pool that are dedicated to serving specific block categories, such
as DDT data, metadata, and small file blocks. A pool can opt-in to
this feature by adding a 'special' or 'dedup' top-level VDEV.
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Alek Pinchuk <apinchuk@datto.com>
Reviewed-by: Håkan Johansson <f96hajo@chalmers.se>
Reviewed-by: Andreas Dilger <andreas.dilger@chamcloud.com>
Reviewed-by: DHE <git@dehacked.net>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: Gregor Kopka <gregor@kopka.net>
Reviewed-by: Kash Pande <kash@tripleback.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Don Brady <don.brady@delphix.com>
Closes#5182
Assertion failed in arc_buf_destroy() when concurrently reading
block with checksum error.
Porting notes:
* The ability to zinject decompression errors has been added, but
this only works at the zio_decompress() level, where we have all
of the info we need to match against the user's zinject options.
* The decompress_fault test has been added to test the new zinject
functionality
* We attempted to set zio_decompress_fail_fraction to (1 << 18) in
ztest for further test coverage. Although this did uncover a few
low priority issues, this unfortuantely also causes ztest to
ASSERT in many locations where the code is working correctly since
it is designed to fail on IO errors. Developers can manually set
this variable with the '-o' option to find and debug issues.
Authored by: Matt Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Matt Ahrens <mahrens@delphix.com>
Ported-by: Tom Caputi <tcaputi@datto.com>
OpenZFS-issue: https://illumos.org/issues/9403
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/fa98e487a9Closes#7822
The following patch introduces a few statistics on reads and writes
grouped by dataset. These statistics are implemented as kstats
(backed by aggregate sums for performance) and can be retrieved by
using the dataset objset ID number. The motivation for this change is
to provide some preliminary analytics on dataset usage/performance.
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Closes#7705
This change simply documents the existing "scripted mode" option in
both command help and man page.
Reviewed-by: Giuseppe Di Natale <guss80@gmail.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#7798
