This change leverage module_param_call() to run arc_tuning_update()
immediately after the ARC tunable has been updated as suggested in
cffa8372 code review.
A simple test case is added to the ZFS Test Suite to prevent future
regressions in functionality.
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#9487Closes#9489
This assert makes non portable assumptions about the state of memory
returned by the memory allocator.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9506
This logic is not platform dependent and should reside in the
common code.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9505
It's mostly a noop on ZoL and it conflicts with platforms that
support dtrace. Remove this header to resolve the conflict.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9497
Contrary to initial testing we cannot rely on these kernels to
invalidate the per-cpu FPU state and restore the FPU registers.
Nor can we guarantee that the kernel won't modify the FPU state
which we saved in the task struck.
Therefore, the kfpu_begin() and kfpu_end() functions have been
updated to save and restore the FPU state using our own dedicated
per-cpu FPU state variables.
This has the additional advantage of allowing us to use the FPU
again in user threads. So we remove the code which was added to
use task queues to ensure some functions ran in kernel threads.
Reviewed-by: Fabian Grünbichler <f.gruenbichler@proxmox.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #9346Closes#9403
Fixes an obvious issue of calling arc_buf_destroy() on an
unallocated arc_buf.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Signed-off-by: Chris Dunlop <chris@onthe.net.au>
Closes#9453
Currently, for certain sizes and classes of allocations we use
SPL caches that are backed by caches in the Linux Slab allocator
to reduce fragmentation and increase utilization of memory. The
way things are implemented for these caches as of now though is
that we don't keep any statistics of the allocations that we
make from these caches.
This patch enables the tracking of allocated objects in those
SPL caches by making the trade-off of grabbing the cache lock
at every object allocation and free to update the respective
counter.
Additionally, this patch makes those caches visible in the
/proc/spl/kmem/slab special file.
As a side note, enabling the specific counter for those caches
enables SDB to create a more user-friendly interface than
/proc/spl/kmem/slab that can also cross-reference data from
slabinfo. Here is for example the output of one of those
caches in SDB that outputs the name of the underlying Linux
cache, the memory of SPL objects allocated in that cache,
and the percentage of those objects compared to all the
objects in it:
```
> spl_kmem_caches | filter obj.skc_name == "zio_buf_512" | pp
name ... source total_memory util
----------- ... ----------------- ------------ ----
zio_buf_512 ... kmalloc-512[SLUB] 16.9MB 8
```
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Closes#9474
Factor Linux specific memory pressure handling out of ARC. Each
platform will have different available interfaces for managing memory
pressure.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9472
Only pass the file descriptor to make zfsdev_get_miror() portable.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9466
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9465
Some platforms, e.g. FreeBSD, support user space setjmp
semantics in kernel.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9450
Clang will complain if a function has no prior declaration
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9467
This addresses a number of problems with dmu_send.c:
* bp_span is unused which makes clang complain
* dump_write conflicts with FreeBSD's existing core dump code
* range_alloc is private to the file and not declared in any headers
causing clang to complain
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9432
We get the sizeof the appropriate type, and don't cast away const.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#9455
FreeBSD has a very different implementation.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9442
FreeBSD has its own implementation as do other platforms.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9439
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chris Dunlop <chris@onthe.net.au>
Closes#9452
Rename certain functions for more consistency when they share common
features. Make comments clearer about what arguments should be passed
to the insert and add functions.
Reviewed by: Sara Hartse <sara.hartse@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Ahrens <matt@delphix.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#9441
It is no longer necessary; mod_compat.h is included from zfs_context.h.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9449
FreeBSD uses this in its pager ops routines
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9431
When "feature@allocation_classes" is not enabled on the pool no vdev
with "special" or "dedup" allocation type should be allowed to exist in
the vdev tree.
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#9427Closes#9429
Temporary property handling at the VFS layer requires
platform specific code.
Reviewed-by: Sean Eric Fagan <sef@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9401
Make the metaslab platform agnostic again by adding
accessor functions which can be implemented by each
platform.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9404
FreeBSD's zvol platform code requires access to the
zil_async_to_sync() function.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9440
In the FreeBSD kernel the strdup signature is:
```
char *strdup(const char *__restrict, struct malloc_type *);
```
It's unfortunate that the developers have chosen to change
the signature of libc functions - but it's what I have to
deal with.
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9433
The macros are used to generate code for conditions without a
corresponding branch. This is not a problem in practice, but
clang has no way of knowing that. Add a default branch with a
VERIFY(0) to indicate that it "can't happen"
```
In file included from \
/usr/home/mmacy/devel/ZoF/module/zfs/vdev_raidz_math_sse2.c:607:
/usr/home/mmacy/devel/ZoF/module/zfs/vdev_raidz_math_impl.h:281:3: \
error: no case matching constant switch condition '3' [-Werror]
```
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9434
This patch implements a new tree structure for ZFS, and uses it to
store range trees more efficiently.
The new structure is approximately a B-tree, though there are some
small differences from the usual characterizations. The tree has core
nodes and leaf nodes; each contain data elements, which the elements
in the core nodes acting as separators between its children. The
difference between core and leaf nodes is that the core nodes have an
array of children, while leaf nodes don't. Every node in the tree may
be only partially full; in most cases, they are all at least 50% full
(in terms of element count) except for the root node, which can be
less full. Underfull nodes will steal from their neighbors or merge to
remain full enough, while overfull nodes will split in two. The data
elements are contained in tree-controlled buffers; they are copied
into these on insertion, and overwritten on deletion. This means that
the elements are not independently allocated, which reduces overhead,
but also means they can't be shared between trees (and also that
pointers to them are only valid until a side-effectful tree operation
occurs). The overhead varies based on how dense the tree is, but is
usually on the order of about 50% of the element size; the per-node
overheads are very small, and so don't make a significant difference.
The trees can accept arbitrary records; they accept a size and a
comparator to allow them to be used for a variety of purposes.
The new trees replace the AVL trees used in the range trees today.
Currently, the range_seg_t structure contains three 8 byte integers
of payload and two 24 byte avl_tree_node_ts to handle its storage in
both an offset-sorted tree and a size-sorted tree (total size: 64
bytes). In the new model, the range seg structures are usually two 4
byte integers, but a separate one needs to exist for the size-sorted
and offset-sorted tree. Between the raw size, the 50% overhead, and
the double storage, the new btrees are expected to use 8*1.5*2 = 24
bytes per record, or 33.3% as much memory as the AVL trees (this is
for the purposes of storing metaslab range trees; for other purposes,
like scrubs, they use ~50% as much memory).
We reduced the size of the payload in the range segments by teaching
range trees about starting offsets and shifts; since metaslabs have a
fixed starting offset, and they all operate in terms of disk sectors,
we can store the ranges using 4-byte integers as long as the size of
the metaslab divided by the sector size is less than 2^32. For 512-byte
sectors, this is a 2^41 (or 2TB) metaslab, which with the default
settings corresponds to a 256PB disk. 4k sector disks can handle
metaslabs up to 2^46 bytes, or 2^63 byte disks. Since we do not
anticipate disks of this size in the near future, there should be
almost no cases where metaslabs need 64-byte integers to store their
ranges. We do still have the capability to store 64-byte integer ranges
to account for cases where we are storing per-vdev (or per-dnode) trees,
which could reasonably go above the limits discussed. We also do not
store fill information in the compact version of the node, since it
is only used for sorted scrub.
We also optimized the metaslab loading process in various other ways
to offset some inefficiencies in the btree model. While individual
operations (find, insert, remove_from) are faster for the btree than
they are for the avl tree, remove usually requires a find operation,
while in the AVL tree model the element itself suffices. Some clever
changes actually caused an overall speedup in metaslab loading; we use
approximately 40% less cpu to load metaslabs in our tests on Illumos.
Another memory and performance optimization was achieved by changing
what is stored in the size-sorted trees. When a disk is heavily
fragmented, the df algorithm used by default in ZFS will almost always
find a number of small regions in its initial cursor-based search; it
will usually only fall back to the size-sorted tree to find larger
regions. If we increase the size of the cursor-based search slightly,
and don't store segments that are smaller than a tunable size floor
in the size-sorted tree, we can further cut memory usage down to
below 20% of what the AVL trees store. This also results in further
reductions in CPU time spent loading metaslabs.
The 16KiB size floor was chosen because it results in substantial memory
usage reduction while not usually resulting in situations where we can't
find an appropriate chunk with the cursor and are forced to use an
oversized chunk from the size-sorted tree. In addition, even if we do
have to use an oversized chunk from the size-sorted tree, the chunk
would be too small to use for ZIL allocations, so it isn't as big of a
loss as it might otherwise be. And often, more small allocations will
follow the initial one, and the cursor search will now find the
remainder of the chunk we didn't use all of and use it for subsequent
allocations. Practical testing has shown little or no change in
fragmentation as a result of this change.
If the size-sorted tree becomes empty while the offset sorted one still
has entries, it will load all the entries from the offset sorted tree
and disregard the size floor until it is unloaded again. This operation
occurs rarely with the default setting, only on incredibly thoroughly
fragmented pools.
There are some other small changes to zdb to teach it to handle btrees,
but nothing major.
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed by: Sebastien Roy seb@delphix.com
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#9181
If stdin if empty - don't run xargs command,
otherwise we can get `cp: missing file operand`
error.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Melikov <mail@gmelikov.ru>
Closes#9418
Commit 093bb64 resolved an automount failures for chroot'd processes
but inadvertently broke automounting for root filesystems where the
vfs_mntpoint is NULL. Resolve the issue by checking for NULL in order
to generate the correct path.
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9381Closes#9384
A rangelock KPI already exists on FreeBSD. Add a zfs_ prefix as
per our convention to prevent any conflict with existing symbols.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9402
Make arc_stats visible to platform code.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9386
We've seen cases where after creating a ZVOL, the ZVOL device node in
"/dev" isn't generated after 20 seconds of waiting, which is the point
at which our applications gives up on waiting and reports an error.
The workload when this occurs is to "refresh" 400+ ZVOLs roughly at the
same time, based on a policy set by the user. This refresh operation
will destroy the ZVOL, and re-create it based on a snapshot.
When this occurs, we see many hundreds of entries on the "z_zvol" taskq
(based on inspection of the /proc/spl/taskq-all file). Many of the
entries on the taskq end up in the "zvol_remove_minors_impl" function,
and I've measured the latency of that function:
Function = zvol_remove_minors_impl
msecs : count distribution
0 -> 1 : 0 | |
2 -> 3 : 0 | |
4 -> 7 : 1 | |
8 -> 15 : 0 | |
16 -> 31 : 0 | |
32 -> 63 : 0 | |
64 -> 127 : 1 | |
128 -> 255 : 45 |****************************************|
256 -> 511 : 5 |**** |
That data is from a 10 second sample, using the BCC "funclatency" tool.
As we can see, in this 10 second sample, most calls took 128ms at a
minimum. Thus, some basic math tells us that in any 20 second interval,
we could only process at most about 150 removals, which is much less
than the 400+ that'll occur based on the workload.
As a result of this, and since all ZVOL minor operations will go through
the single threaded "z_zvol" taskq, the latency for creating a single
ZVOL device can be unreasonably large due to other ZVOL activity on the
system. In our case, it's large enough to cause the application to
generate an error and fail the operation.
When profiling the "zvol_remove_minors_impl" function, I saw that most
of the time in the function was spent off-cpu, blocked in the function
"taskq_wait_outstanding". How this works, is "zvol_remove_minors_impl"
will dispatch calls to "zvol_free" using the "system_taskq", and then
the "taskq_wait_outstanding" function is used to wait for all of those
dispatched calls to occur before "zvol_remove_minors_impl" will return.
As far as I can tell, "zvol_remove_minors_impl" doesn't necessarily have
to wait for all calls to "zvol_free" to occur before it returns. Thus,
this change removes the call to "taskq_wait_oustanding", so that calls
to "zvol_free" don't affect the latency of "zvol_remove_minors_impl".
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Gallagher <john.gallagher@delphix.com>
Signed-off-by: Prakash Surya <prakash.surya@delphix.com>
Closes#9380
Refactor the zfs ioctls in to platform dependent and independent bits.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Sean Eric Fagan <sef@ixsystems.com>
Signed-off-by: Matthew Macy <mmacy@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#9301
Originally the zfs_vdev_elevator module option was added as a
convenience so the requested elevator would be automatically set
on the underlying block devices. At the time this was simple
because the kernel provided an API function which did exactly this.
This API was then removed in the Linux 4.12 kernel which prompted
us to add compatibly code to set the elevator via a usermodehelper.
While well intentioned this introduced a bug which could cause a
system hang, that issue was subsequently fixed by commit 2a0d4188.
In order to avoid future bugs in this area, and to simplify the code,
this functionality is being deprecated. A console warning has been
added to notify any existing consumers and the documentation updated
accordingly. This option will remain for the lifetime of the 0.8.x
series for compatibility but if planned to be phased out of master.
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #8664Closes#9317
Refactor the zvol in to platform dependent and independent bits.
Reviewed-by: Allan Jude <allanjude@freebsd.org>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9295
Trying to 'zfs diff' a snapshot with large dnodes will incorrectly try
to access its interior slots when dnodesize > sizeof(dnode_phys_t).
This is normally not an issue because the interior slots are
zero-filled, which report_dnode() handles calling
report_free_dnode_range(). However this is not the case for encrypted
large dnodes or filesystem using many SA based xattrs where the extra
data past the legacy dnode size boundary is interpreted as a
dnode_phys_t.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#7678Closes#8931Closes#9343
When a disk is replaced with another on a pool with the resilver_defer
feature present, but not enabled the resilver activity restarts during
each spa_sync. This patch checks to make sure that the resilver_defer
feature is first enabled before requesting a deferred resilver.
This was originally fixed in illumos-joyent as OS-7982.
Reviewed-by: Chris Dunlop <chris@onthe.net.au>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed by: Jerry Jelinek <jerry.jelinek@joyent.com>
Signed-off-by: Kody A Kantor <kody@kkantor.com>
External-issue: illumos-joyent OS-7982
Closes#9299Closes#9338
The was incorrect with respect to swapping dataset IDs both in the
on-disk ZAP object and the in-memory queue.
In both cases, if ds1 was already present, then it would be first
replaced with ds2 and then ds would be replaced back with ds1.
Also, both cases did not properly handle a situation where both ds1 and
ds2 are already queued. A duplicate insertion would be attempted and
its failure would result in a panic.
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: Andriy Gapon <avg@FreeBSD.org>
Closes#9140Closes#9163
This commit fixes a NULL pointer dereference triggered in
spa_vdev_remove_top_check() by trying to "zpool remove" an indirect
vdev.
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#9327
This commit fixes the following build failure detected on Debian9
(GCC 6.3.0):
CC [M] module/zfs/spa.o
module/zfs/spa.c: In function ‘spa_wait_common.part.31’:
module/zfs/spa.c:9468:6: error: ‘in_progress’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
if (!in_progress || spa->spa_waiters_cancel || error)
^
cc1: all warnings being treated as errors
Reviewed-by: Chris Dunlop <chris@onthe.net.au>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Gallagher <john.gallagher@delphix.com>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#9326
Currently, spa_keystore_change_key_sync_impl() does not recurse
into clones when updating encryption roots for either a call to
'zfs promote' or 'zfs change-key'. This can cause children of
these clones to end up in a state where they point to the wrong
dataset as the encryption root. It can also trigger ASSERTs in
some cases where the code checks reference counts on wrapping
keys. This patch fixes this issue by ensuring that this function
properly recurses into clones during processing.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alek Pinchuk <apinchuk@datto.com>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#9267Closes#9294
Originally the zfs_vdev_elevator module option was added as a
convenience so the requested elevator would be automatically set
on the underlying block devices. At the time this was simple
because the kernel provided an API function which did exactly this.
This API was then removed in the Linux 4.12 kernel which prompted
us to add compatibly code to set the elevator via a usermodehelper.
Unfortunately changing the evelator via usermodehelper requires reading
some userland binaries, most notably modprobe(8) or sh(1), from a zfs
dataset on systems with root-on-zfs. This can deadlock the system if
used during the following call path because it may need, if the data
is not already cached in the ARC, reading directly from disk while
holding the spa config lock as a writer:
zfs_ioc_pool_scan()
-> spa_scan()
-> spa_scan()
-> vdev_reopen()
-> vdev_elevator_switch()
-> call_usermodehelper()
While the usermodehelper waits sh(1), modprobe(8) is blocked in the
ZIO pipeline trying to read from disk:
INFO: task modprobe:2650 blocked for more than 10 seconds.
Tainted: P OE 5.2.14
modprobe D 0 2650 206 0x00000000
Call Trace:
? __schedule+0x244/0x5f0
schedule+0x2f/0xa0
cv_wait_common+0x156/0x290 [spl]
? do_wait_intr_irq+0xb0/0xb0
spa_config_enter+0x13b/0x1e0 [zfs]
zio_vdev_io_start+0x51d/0x590 [zfs]
? tsd_get_by_thread+0x3b/0x80 [spl]
zio_nowait+0x142/0x2f0 [zfs]
arc_read+0xb2d/0x19d0 [zfs]
...
zpl_iter_read+0xfa/0x170 [zfs]
new_sync_read+0x124/0x1b0
vfs_read+0x91/0x140
ksys_read+0x59/0xd0
do_syscall_64+0x4f/0x130
entry_SYSCALL_64_after_hwframe+0x44/0xa9
This commit changes how we use the usermodehelper functionality from
synchronous (UMH_WAIT_PROC) to asynchronous (UMH_NO_WAIT) which prevents
scrubs, and other vdev_elevator_switch() consumers, from triggering the
aforementioned issue.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Issue #8664Closes#9321
Currently the best way to wait for the completion of a long-running
operation in a pool, like a scrub or device removal, is to poll 'zpool
status' and parse its output, which is neither efficient nor convenient.
This change adds a 'wait' subcommand to the zpool command. When invoked,
'zpool wait' will block until a specified type of background activity
completes. Currently, this subcommand can wait for any of the following:
- Scrubs or resilvers to complete
- Devices to initialized
- Devices to be replaced
- Devices to be removed
- Checkpoints to be discarded
- Background freeing to complete
For example, a scrub that is in progress could be waited for by running
zpool wait -t scrub <pool>
This also adds a -w flag to the attach, checkpoint, initialize, replace,
remove, and scrub subcommands. When used, this flag makes the operations
kicked off by these subcommands synchronous instead of asynchronous.
This functionality is implemented using a new ioctl. The type of
activity to wait for is provided as input to the ioctl, and the ioctl
blocks until all activity of that type has completed. An ioctl was used
over other methods of kernel-userspace communiction primarily for the
sake of portability.
Porting Notes:
This is ported from Delphix OS change DLPX-44432. The following changes
were made while porting:
- Added ZoL-style ioctl input declaration.
- Reorganized error handling in zpool_initialize in libzfs to integrate
better with changes made for TRIM support.
- Fixed check for whether a checkpoint discard is in progress.
Previously it also waited if the pool had a checkpoint, instead of
just if a checkpoint was being discarded.
- Exposed zfs_initialize_chunk_size as a ZoL-style tunable.
- Updated more existing tests to make use of new 'zpool wait'
functionality, tests that don't exist in Delphix OS.
- Used existing ZoL tunable zfs_scan_suspend_progress, together with
zinject, in place of a new tunable zfs_scan_max_blks_per_txg.
- Added support for a non-integral interval argument to zpool wait.
Future work:
ZoL has support for trimming devices, which Delphix OS does not. In the
future, 'zpool wait' could be extended to add the ability to wait for
trim operations to complete.
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: John Gallagher <john.gallagher@delphix.com>
Closes#9162
1. Fix issue: Kernel BUG with QAT during decompression #9276.
Now it is uninterruptible for a specific given QAT request,
but Ctrl-C interrupt still works in user-space process.
2. Copy the digest result to the buffer only when doing encryption,
and vise-versa for decryption.
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chengfei Zhu <chengfeix.zhu@intel.com>
Closes#9276Closes#9303
objnode is OS agnostic and used only by dmu_redact.c.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9315
Move Linux specific tracing headers and source to platform directories
and update the build system.
Reviewed-by: Allan Jude <allanjude@freebsd.org>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed by: Brad Lewis <brad.lewis@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9290
Currently, the DSL scan code figures out when it should suspend
processing and allow a txg to continue by calling the function
dsl_scan_check_suspend(). Unfortunately, this function only
allows the scan to suspend at a level 0 block. In the event that
the system is scanning a bunch of empty snapshots or a resilver
is running with a high enough scn_cur_min_txg, the scan will
stop processing each dataset at the root level, deciding it
has nothing left to do. This means that the check_suspend
function is never called and the txg remains stuck until a
dataset is found that has data to scan.
This patch fixes the problem by allowing scans to suspend at
the root level of the objset. For backwards compatibility, we
use the bookmark <objsetid, 0, 0, 0> when we suspend here so
that older versions of the code will work as intended.
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#9300
Accidentally introduced by dc04a8c which now takes the SCL_VDEV lock
as a reader in zfs_blkptr_verify(). A deadlock can occur if the
/etc/hostid file resides on a dataset in the same pool. This is
because reading the /etc/hostid file may occur while the caller is
holding the SCL_VDEV lock as a writer. For example, to perform a
`zpool attach` as shown in the abbreviated stack below.
To resolve the issue we cache the system's hostid when initializing
the spa_t, or when modifying the multihost property. The cached
value is then relied upon for subsequent accesses.
Call Trace:
spa_config_enter+0x1e8/0x350 [zfs]
zfs_blkptr_verify+0x33c/0x4f0 [zfs] <--- trying read lock
zio_read+0x6c/0x140 [zfs]
...
vfs_read+0xfc/0x1e0
kernel_read+0x50/0x90
...
spa_get_hostid+0x1c/0x38 [zfs]
spa_config_generate+0x1a0/0x610 [zfs]
vdev_label_init+0xa0/0xc80 [zfs]
vdev_create+0x98/0xe0 [zfs]
spa_vdev_attach+0x14c/0xb40 [zfs] <--- grabbed write lock
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9256Closes#9285
When adding the SIMD compatibility code in e5db313 the decryption of a
dataset wrapping key was left in a user thread context. This was done
intentionally since it's a relatively infrequent operation. However,
this also meant that the encryption context templates were initialized
using the generic operations. Therefore, subsequent encryption and
decryption operations would use the generic implementation even when
executed by an I/O pipeline thread.
Resolve the issue by initializing the context templates in an I/O
pipeline thread. And by updating zio_do_crypt_uio() to dispatch any
encryption operations to a pipeline thread when called from the user
context. For example, when performing a read from the ARC.
Tested-by: Attila Fülöp <attila@fueloep.org>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9215Closes#9296
Move platform specific Linux source under module/os/linux/
and update the build system accordingly. Additional code
restructuring will follow to make the common code fully
portable.
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Macy <mmacy@FreeBSD.org>
Closes#9206
Adds ZFS_MODULE_PARAM to abstract module parameter
setting to operating systems other than Linux.
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#9230
`metaslab_verify_weight_and_frag()` a verification function and
by the end of it there shouldn't be any side-effects.
The function calls `metaslab_weight()` which in turn calls
`metaslab_set_fragmentation()`. The latter can dirty and otherwise
not dirty metaslab fro the next TXGand set `metaslab_condense_wanted`
if the spacemaps were just upgraded (meaning we just enabled the
SPACEMAP_HISTOGRAM feature through upgrade).
This patch adds a new flag as a parameter to `metaslab_weight()` and
`metaslab_set_fragmentation()` making the dirtying of the metaslab
optional.
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Closes#9185Closes#9282
Move platform specific Linux headers under include/os/linux/.
Update the build system accordingly to detect the platform.
This lays some of the initial groundwork to supporting building
for other platforms.
As part of this change it was necessary to create both a user
and kernel space sys/simd.h header which can be included in
either context. No functional change, the source has been
refactored and the relevant #include's updated.
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Signed-off-by: Matthew Macy <mmacy@FreeBSD.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9198
Account for ZFS_MAX_DATASET_NAME_LEN in kstat data size. This value
is ignored in the Linux kstat code but resolves the issue for other
platforms.
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Igor Kozhukhov <igor@dilos.org>
Closes#9254Closes#9151
This fixes a hole in the situation where the resume state is left from
receiving a new dataset and, so, the state is set on the dataset itself
(as opposed to %recv child).
Additionally, distinguish incremental and resume streams in error
messages.
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andriy Gapon <avg@FreeBSD.org>
Closes#9252
This change use the compat code introduced in 9cc1844a.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#9268Closes#9269
When running on larger memory systems, we can overflow the value of
maxinflight. This can result in maxinflight having a value of 0 causing
the system to hang.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Wilson <george.wilson@delphix.com>
Closes#9272
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Closes#9240
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Closes#9241
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Closes#9239
If a pool enables the SPACEMAP_HISTOGRAM feature shortly before being
exported, we can enter a situation that causes a kernel panic. Any metaslabs
that are loaded during the final dirty txg and haven't already been condensed
will cause metaslab_sync to proceed after the final dirty txg so that the
condense can be performed, which there are assertions to prevent. Because of
the nature of this issue, there are a number of ways we can enter this
state. Rather than try to prevent each of them one by one, potentially missing
some edge cases, we instead cut it off at the point of intersection; by
preventing metaslab_sync from proceeding if it would only do so to perform a
condense and we're past the final dirty txg, we preserve the utility of the
existing asserts while preventing this particular issue.
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#9185Closes#9186Closes#9231Closes#9253
With the other metaslab changes loaded onto a system, we can
significantly reduce the memory usage of each loaded metaslab and
unload them on demand if there is memory pressure. However, none
of those changes actually result in us keeping more metaslabs loaded.
If we don't keep more metaslabs loaded, we will still have to wait
for demand-loading to finish when no loaded metaslab can satisfy our
allocation, which can cause ZIL performance issues. In addition,
performance is traditionally measured by IOs per unit time, while
unloading is currently done on a txg-count basis. Txgs can take a
widely varying range of times, from tenths of a second to several
seconds. This can result in confusing, hard to predict behavior.
This change simply adds a time-based component to metaslab unloading.
A metaslab will remain loaded for one minute and 8 txgs (by default)
after it was last used, unless it is evicted due to memory pressure.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
External-issue: DLPX-65016
External-issue: DLPX-65047
Closes#9197
For interrupt coalescing, cv_timedwait_hires() uses a 100us slack/delta
for calls to schedule_hrtimeout_range(). This 100us slack can be costly
for small writes.
This change improves small write performance by passing resolution `res`
parameter to schedule_hrtimeout_range() to be used as delta/slack. A new
tunable `spl_schedule_hrtimeout_slack_us` is added to preserve old
behavior when desired.
Performance observations on 8K recordsize filesystem:
- 8K random writes at 1-64 threads, up to 60% improvement for one thread
and smaller gains as thread count increases. At >64 threads, 2-5%
decrease in performance was observed.
- 8K sequential writes, similar 60% improvement for one thread and
leveling out around 64 threads. At >64 threads, 5-10% decrease in
performance was observed.
- 128K sequential write sees 1-5 for the 128K. No observed regression at
high thread count.
Testing done on Ubuntu 18.04 with 4.15 kernel, 8vCPUs and SSD storage on
VMware ESX.
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Signed-off-by: Tony Nguyen <tony.nguyen@delphix.com>
Closes#9217
Tag the ABD data pages so that they can be identified for exclusion
from kernel crash dumps. Eliminating the zfs file data allows for
significantly smaller crash dump files. Note that ZFS in illumos has
always excluded the zfs data pages from a kernel crash dump.
This change tags ARC scatter data pages so they can be identified from
the makedumpfile(8) command. That command is used to create smaller
dump files by ignoring some memory regions and using compression. It
already filters file data from the VFS page cache and will now be able
to exclude ZFS file data pages from the dump file.
A corresponding change to makeumpfile(8) is required to identify ZFS
data pages.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Signed-off-by: Don Brady <don.brady@delphix.com>
Closes#8899
If TX_REMOVE is followed by TX_CREATE on the same object id, we need to
make sure the object removal is completely finished before creation. The
current implementation relies on dnode_hold_impl with
DNODE_MUST_BE_ALLOCATED returning ENOENT. While this check seems to work
fine before, in current version it does not guarantee the object removal
is completed.
We fix this by checking if DNODE_MUST_BE_FREE returns successful
instead. Also add test and remove dead code in dnode_hold_impl.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: Chunwei Chen <david.chen@nutanix.com>
Closes#7151Closes#8910Closes#9123Closes#9145
Previously, the permissions were checked on the pool which was obviously
incorrect.
After this change, zfs_check_userprops() only validates the properties
without any permission checks. The permissions are checked individually
for each snapshotted dataset.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Signed-off-by: Andriy Gapon <avg@FreeBSD.org>
Closes#9179Closes#9180
Currently, the 'zfs rollback' code can end up deadlocked due to
the way the kernel handles unreferenced inodes on a suspended fs.
Essentially, the zfs_resume_fs() code path may cause zfs to spawn
new threads as it reinstantiates the suspended fs's zil. When a
new thread is spawned, the kernel may attempt to free memory for
that thread by freeing some unreferenced inodes. If it happens to
select inodes that are a a part of the suspended fs a deadlock
will occur because freeing inodes requires holding the fs's
z_teardown_inactive_lock which is still held from the suspend.
This patch corrects this issue by adding an additional reference
to all inodes that are still present when a suspend is initiated.
This prevents them from being freed by the kernel for any reason.
Reviewed-by: Alek Pinchuk <apinchuk@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#9203
Fix some switch() fall-though compiler errors:
abd.c:1504:9: error: this statement may fall through
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#9170
When there are many snapshots, calls to zfs_ioc_space_snaps() (e.g. from
`zfs destroy -nv pool/fs@snap1%snap10000`) can be very slow, resulting
in poor performance because we are holding the dp_config_rwlock the
entire time, blocking spa_sync() from continuing. With around ten
thousand snapshots, we've seen up to 500 seconds in this ioctl,
iterating over up to 50,000,000 bpobjs, ~99% of which are the empty
bpobj.
By creating a fast path for zfs_ioc_space_snaps() handling of the
empty_bpobj, we can achieve a ~5x performance improvement of this ioctl
(when there are many snapshots, and the deadlist is mostly
empty_bpobj's).
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
External-issue: DLPX-58348
Closes#8744
There are two different deadlock scenarios, but they share a common
link, which is
thread 1 holding sa_lock and trying to get zap->zap_rwlock:
zap_lockdir_impl+0x858/0x16c0 [zfs]
zap_lockdir+0xd2/0x100 [zfs]
zap_lookup_norm+0x7f/0x100 [zfs]
zap_lookup+0x12/0x20 [zfs]
sa_setup+0x902/0x1380 [zfs]
zfsvfs_init+0x3d6/0xb20 [zfs]
zfsvfs_create+0x5dd/0x900 [zfs]
zfs_domount+0xa3/0xe20 [zfs]
and thread 2 trying to get sa_lock, either in sa_setup:
sa_setup+0x742/0x1380 [zfs]
zfsvfs_init+0x3d6/0xb20 [zfs]
zfsvfs_create+0x5dd/0x900 [zfs]
zfs_domount+0xa3/0xe20 [zfs]
or in sa_build_index:
sa_build_index+0x13d/0x790 [zfs]
sa_handle_get_from_db+0x368/0x500 [zfs]
zfs_znode_sa_init.isra.0+0x24b/0x330 [zfs]
zfs_znode_alloc+0x3da/0x1a40 [zfs]
zfs_zget+0x39a/0x6e0 [zfs]
zfs_root+0x101/0x160 [zfs]
zfs_domount+0x91f/0xea0 [zfs]
From there, there are different locking paths back to something
holding zap->zap_rwlock.
The deadlock scenarios involve multiple different ZFS filesystems
being mounted. sa_lock is common to these scenarios, and the sa
struct involved is private to a mount. Therefore, these must be
referring to different sa_lock instances and these deadlocks can't
occur in practice.
The fix, from Brian Behlendorf, is to remove sa_lock from lockdep
coverage by initializing it with MUTEX_NOLOCKDEP.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jeff Dike <jdike@akamai.com>
Closes#9110
Uses obj-m instead, due to kernel changes.
See LKML: Masahiro Yamada, Tue, 6 Aug 2019 19:03:23 +0900
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Dominic Pearson <dsp@technoanimal.net>
Closes#9169
On systems with large amounts of storage and high fragmentation, a huge
amount of space can be used by storing metaslab range trees. Since
metaslabs are only unloaded during a txg sync, and only if they have
been inactive for 8 txgs, it is possible to get into a state where all
of the system's memory is consumed by range trees and metaslabs, and
txgs cannot sync. While ZFS knows how to evict ARC data when needed,
it has no such mechanism for range tree data. This can result in boot
hangs for some system configurations.
First, we add the ability to unload metaslabs outside of syncing
context. Second, we store a multilist of all loaded metaslabs, sorted
by their selection txg, so we can quickly identify the oldest
metaslabs. We use a multilist to reduce lock contention during heavy
write workloads. Finally, we add logic that will unload a metaslab
when we're loading a new metaslab, if we're using more than a certain
fraction of the available memory on range trees.
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Sebastien Roy <sebastien.roy@delphix.com>
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#9128
Even though the bug's writeup (Github issue #9136) is very detailed,
we still don't know exactly how we got to that state, thus I wasn't
able to reproduce the bug. That said, we can make an educated guess
combining the information on filled issue with the code.
From the fact that `dp_dirty_total` was 0 (which is less than
`zfs_dirty_data_max`) we know that there was one thread that set it to
0 and then signaled one of the waiters of `dp_spaceavail_cv` [see
`dsl_pool_dirty_delta()` which is also the only place that
`dp_dirty_total` is changed]. Thus, the only logical explaination
then for the bug being hit is that the waiter that just got awaken
didn't go through `dsl_pool_dirty_data()`. Given that this function
is only called by `dsl_pool_dirty_space()` or `dsl_pool_undirty_space()`
I can only think of two possible ways of the above scenario happening:
[1] The waiter didn't call into any of the two functions - which I
find highly unlikely (i.e. why wait on `dp_spaceavail_cv` to begin
with?).
[2] The waiter did call in one of the above function but it passed 0 as
the space/delta to be dirtied (or undirtied) and then the callee
returned immediately (e.g both `dsl_pool_dirty_space()` and
`dsl_pool_undirty_space()` return immediately when space is 0).
In any case and no matter how we got there, the easy fix would be to
just broadcast to all waiters whenever `dp_dirty_total` hits 0. That
said and given that we've never hit this before, it would make sense
to think more on why the above situation occured.
Attempting to mimic what Prakash was doing in the issue filed, I
created a dataset with `sync=always` and started doing contiguous
writes in a file within that dataset. I observed with DTrace that even
though we update the pool's dirty data accounting when we would dirty
stuff, the accounting wouldn't be decremented incrementally as we were
done with the ZIOs of those writes (the reason being that
`dbuf_write_physdone()` isn't be called as we go through the override
code paths, and thus `dsl_pool_undirty_space()` is never called). As a
result we'd have to wait until we get to `dsl_pool_sync()` where we
zero out all dirty data accounting for the pool and the current TXG's
metadata.
In addition, as Matt noted and I later verified, the same issue would
arise when using dedup.
In both cases (sync & dedup) we shouldn't have to wait until
`dsl_pool_sync()` zeros out the accounting data. According to the
comment in that part of the code, the reasons why we do the zeroing,
have nothing to do with what we observe:
````
/*
* We have written all of the accounted dirty data, so our
* dp_space_towrite should now be zero. However, some seldom-used
* code paths do not adhere to this (e.g. dbuf_undirty(), also
* rounding error in dbuf_write_physdone).
* Shore up the accounting of any dirtied space now.
*/
dsl_pool_undirty_space(dp, dp->dp_dirty_pertxg[txg & TXG_MASK], txg);
````
Ideally what we want to do is to undirty in the accounting exactly what
we dirty (I use the word ideally as we can still have rounding errors).
This would make the behavior of the system more clear and predictable.
Another interesting issue that I observed with DTrace was that we
wouldn't update any of the pool's dirty data accounting whenever we
would dirty and/or undirty MOS data. In addition, every time we would
change the size of a dbuf through `dbuf_new_size()` we wouldn't update
the accounted space dirtied in the appropriate dirty record, so when
ZIOs are done we would undirty less that we dirtied from the pool's
accounting point of view.
For the first two issues observed (sync & dedup) this patch ensures
that we still update the pool's accounting when we undirty data,
regardless of the write being physical or not.
For changes in the MOS, we first ensure to zero out the pool's dirty
data accounting in `dsl_pool_sync()` after we synced the MOS. Then we
can go ahead and enable the update of the pool's dirty data accounting
wheneve we change MOS data.
Another fix is that we now update the accounting explicitly for
counting errors in `dbuf_write_done()`.
Finally, `dbuf_new_size()` updates the accounted space of the
appropriate dirty record correctly now.
The problem is that we still don't know how the bug came up in the
issue filled. That said the issues fixed seem to be very relevant, so
instead of going with the broadcasting solution right away,
I decided to leave this patch as is.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Prakash Surya <prakash.surya@delphix.com>
Signed-off-by: Serapheim Dimitropoulos <serapheim@delphix.com>
External-issue: DLPX-47285
Closes#9137
In zfs_log_write(), we can use dmu_read_by_dnode() rather than
dmu_read() thus avoiding unnecessary dnode_hold() calls.
We get a 2-5% performance gain for large sequential_writes tests, >=128K
writes to files with recordsize=8K.
Testing done on Ubuntu 18.04 with 4.15 kernel, 8vCPUs and SSD storage on
VMware ESX.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Nguyen <tony.nguyen@delphix.com>
Closes#9156
This patch introduces an assertion that can catch pitfalls in
development where there is a mismatch between the size of
reads and writes between a *_phys structure and its respective
in-core structure when bonus buffers are used.
This debugging-aid should be complementary to the verification
done by ztest in ztest_verify_dnode_bt().
A side to this patch is that we now clear out any extra bytes
past a bonus buffer's new size when the buffer is shrinking.
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Closes#8348
The call to txg_wait_synced in zfsvfs_teardown should
be made conditional on the objset having dirty data.
This can prevent unnecessary txg_wait_synced during
some unmount operations.
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Zuchowski <pzuchowski@datto.com>
Closes#9115
When we check the vdev of the blkptr in zfs_blkptr_verify, we can run
into a race condition where that vdev is temporarily unavailable. This
happens when a device removal operation and the old vdev_t has been
removed from the array, but the new indirect vdev has not yet been
inserted.
We hold the spa_config_lock while doing our sensitive verification.
To ensure that we don't deadlock, we only grab the lock if we don't
have config_writer held. In addition, I had to const the tags of the
refcounts and the spa_config_lock arguments.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#9112
We should only call zil_remove_async when an object is removed. However,
in current implementation, it is called whenever TX_REMOVE is called. In
the case of hardlinked file, every unlink will generate TX_REMOVE and
causing operations to be dropped even when the object is not removed.
We fix this by only calling zil_remove_async when the file is fully
unlinked.
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Prakash Surya <prakash.surya@delphix.com>
Signed-off-by: Chunwei Chen <david.chen@nutanix.com>
Closes#8769Closes#9061
This function is not used outside of dsl_dataset.c
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed by: Sara Hartse <sara.hartse@delphix.com>
Signed-off-by: Allan Jude <allanjude@freebsd.org>
Closes#9154
When a pool is imported it will scan the pool to verify the integrity
of the data and metadata. The amount it scans will depend on the
import flags provided. On systems with small amounts of memory or
when importing a pool from the crash kernel, it's possible for
spa_load_verify to issue too many I/Os that it consumes all the memory
of the system resulting in an OOM message or a hang.
To prevent this, we limit the amount of memory that the initial pool
scan can consume. This change will, by default, use 1/16th of the ARC
for scan I/Os to prevent running the system out of memory during import.
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Signed-off-by: George Wilson george.wilson@delphix.com
External-issue: DLPX-65237
External-issue: DLPX-65238
Closes#9146
Given znode_t is an in-core structure, it's more readable to have
them as boolean. Also co-locate existing boolean fields with them
for space efficiency (expecting 8 booleans to be packed/aligned).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@gmail.com>
Closes#9092
This is not implemented. If it were implemented, using it would risk
deadlocks on pre-3.18 kernels. Lets just drop it.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Signed-off-by: Richard Yao <ryao@gentoo.org>
Closes#9119
Consumers of ZFS Channel Programs can now list bookmarks,
and get holds from datasets. A minor-refactoring was also
applied to distinguish between user and system properties
in ZCP.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Ported-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Signed-off-by: Dan Kimmel <dan.kimmel@delphix.com>
OpenZFS-issue: https://illumos.org/issues/8862Closes#7902
Beside the whole commit being a nit in reality it should
bring the diffs of the spa_log_spacemap.c source file
between ZoL and delphix/zfs to 0.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Chris Dunlop <chris@onthe.net.au>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Closes#9143
When we unload metaslabs today in ZFS, the cached max_size value is
discarded. We instead use the histogram to determine whether or not we
think we can satisfy an allocation from the metaslab. This can result in
situations where, if we're doing I/Os of a size not aligned to a
histogram bucket, a metaslab is loaded even though it cannot satisfy the
allocation we think it can. For example, a metaslab with 16 entries in
the 16k-32k bucket may have entirely 16kB entries. If we try to allocate
a 24kB buffer, we will load that metaslab because we think it should be
able to handle the allocation. Doing so is expensive in CPU time, disk
reads, and average IO latency. This is exacerbated if the write being
attempted is a sync write.
This change makes ZFS cache the max_size after the metaslab is
unloaded. If we ever get a free (or a coalesced group of frees) larger
than the max_size, we will update it. Otherwise, we leave it as is. When
attempting to allocate, we use the max_size as a lower bound, and
respect it unless we are in try_hard. However, we do age the max_size
out at some point, since we expect the actual max_size to increase as we
do more frees. A more sophisticated algorithm here might be helpful, but
this works reasonably well.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#9055
ZED can prevent CPU's from properly sleeping.
Rather than periodically waking up in the zevents code, just go to sleep and wait for a wakeup.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: DHE <git@dehacked.net>
Closes#9091
This fixes a lockdep warning by breaking a link between ->tx_sync_lock
and ->dp_lock.
The deadlock envisioned by lockdep is this:
thread 1 holds db->db_mtx and tries to get dp->dp_lock:
dsl_pool_dirty_space+0x70/0x2d0 [zfs]
dbuf_dirty+0x778/0x31d0 [zfs]
thread 2 holds bpo->bpo_lock and tries to get db->db_mtx:
dmu_buf_will_dirty_impl
dmu_buf_will_dirty+0x6b/0x6c0 [zfs]
bpobj_iterate_impl+0xbe6/0x1410 [zfs]
thread 3 holds tx->tx_sync_lock and tries to get bpo->bpo_lock:
bpobj_space+0x63/0x470 [zfs]
dsl_scan_active+0x340/0x3d0 [zfs]
txg_sync_thread+0x3f2/0x1370 [zfs]
thread 4 holds dp->dp_lock and tries to get tx->tx_sync_lock
txg_kick+0x61/0x420 [zfs]
dsl_pool_need_dirty_delay+0x1c7/0x3f0 [zfs]
This patch is orginally from Brian Behlendorf and slightly simplified
by me.
It breaks this cycle in thread 4 by moving the call from
dsl_pool_need_dirty_delay to txg_kick outside the section controlled
by dp->dp_lock.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Signed-off-by: Jeff Dike <jdike@akamai.com>
Closes#9094
In spa_ld_log_sm_metadata(), it is possible for zap_cursor_retrieve()
to return errors other than the expected ENOENT (e.g. when we are at
the end of the zap). Ensure that these error cases are handled
correctly by the import path.
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Sara Hartse <sara.hartse@delphix.com>
Reviewed by: Matt Ahrens <matt@delphix.com>
Signed-off-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Closes#9074
When the log spacemap commit was merged in ZoL, the
metaslab_verify_unflushed_changes() debugging function
was deleted as the feature was pretty much stable by
then. Unfortunately though there was a reference to
it from a comment in metaslab_verify_weight_and_frag().
This patch deletes the reference and pastes that
comment as is.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Closes#9097
In zfs_write() and dmu_tx_hold_sa(), we can use dmu_tx_hold_*_by_dnode()
instead of dmu_tx_hold_*(), since we already have a dbuf from the target
dnode in hand. This eliminates some calls to dnode_hold(), which can be
expensive. This is especially impactful if several threads are
accessing objects that are in the same block of dnodes, because they
will contend for that dbuf's lock.
We are seeing 10-20% performance wins for the sequential_writes tests in
the performance test suite, when doing >=128K writes to files with
recordsize=8K.
This also removes some unnecessary casts that are in the area.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#9081
When adapting the original sources for s390x the JMP_BUF_CNT was
mistakenly halved due to an incorrect assumption of the size of
a unsigned long. They are 8 bytes for the s390x architecture.
Increase JMP_BUF_CNT accordingly.
Authored-by: Don Brady <don.brady@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reported-by: Colin Ian King <canonical.com>
Tested-by: Colin Ian King <canonical.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8992Closes#9080
Don't unconditionally return 0 (i.e. retain SUID/SGID).
Test CAP_FSETID capability.
https://github.com/pjd/pjdfstest/blob/master/tests/chmod/12.t
which expects SUID/SGID to be dropped on write(2) by non-owner fails
without this. Most filesystems make this decision within VFS by using
a generic file write for fops.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@gmail.com>
Closes#9035Closes#9043
Deleting a clone requires finding blocks are clone-only, not shared
with the snapshot. This was done by traversing the entire block tree
which results in a large performance penalty for sparsely
written clones.
This is new method keeps track of clone blocks when they are
modified in a "Livelist" so that, when it’s time to delete,
the clone-specific blocks are already at hand.
We see performance improvements because now deletion work is
proportional to the number of clone-modified blocks, not the size
of the original dataset.
Reviewed-by: Sean Eric Fagan <sef@ixsystems.com>
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Signed-off-by: Sara Hartse <sara.hartse@delphix.com>
Closes#8416
Cast to uintptr_t first for portability on integer to/from pointer
conversion.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@gmail.com>
Closes#9065
The rwlock implementation on linux does not perform as well as mutexes.
We can realize a performance benefit by replacing the zf_rwlock with a
mutex. Local microbenchmarks show ~50% improvement, and over NFS we see
~5% improvement on several of the ZFS Performance Tests cases,
especially randwrite and seq_write.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#9062
metaslab_should_allocate() is used in two places:
[1] When trying to select a metaslab to allocate from
[2] When trying to allocate from a metaslab
In [2] we always expect the metaslab to be loaded, and after
the refactoring of the log spacemap changes, whenever we load
a metaslab we set ms_max_size to the biggest range in the
ms_allocatable tree. Thus, when it is used in [2], if that
field is 0, it means that the metaslab doesn't have any
segments that can be used for allocations now (though it may
have some free space but that space can be in the freeing,
freed, or deferred trees).
In [1] a metaslab can be loaded or unloaded at which point 0
can either mean the metaslab doesn't have any space or the
metaslab is just not loaded thus we go ahead and try to make
an estimation based on its weight.
The issue here is when we call the above function for [2] and
the metaslab doesn't have any allocatable space, we still go
ahead and check its ms_weight which may be out of date because
we haven't ran metaslab_sync_done() yet. At that point we are
allowing an allocation to be attempted even though we know
there is no range that is allocatable.
This patch fixes this issue by explicitly checking if the
metaslab is loaded and if it is, the ms_max_size is used.
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Closes#9045
In the past we've seen multiple race conditions that have
to do with open-context threads async threads and concurrent
calls to spa_export()/spa_destroy() (including the one
referenced in issue #9015).
This patch ensures that only one thread can execute the
main body of spa_export_common() at a time, with subsequent
threads returning with a new error code created just for
this situation, eliminating this way any race condition
bugs introduced by concurrent calls to this function.
Reviewed by: Matt Ahrens <matt@delphix.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Closes#9015Closes#9044
There exists a race condition were hdr_recl() calls
zthr_wakeup() on a destroyed zthr. The timeline is the
following:
[1] hdr_recl() runs first and goes intro zthr_wakeup()
because arc_initialized is set.
[2] arc_fini() is called by another thread, zeroes
that flag, destroying the zthr, and goes into
buf_init().
[3] hdr_recl() tries to enter the destroyed mutex
and we blow up.
This patch ensures that the ARC's zthrs are not offloaded
any new work once arc_initialized is set and then destroys
them after all of the ARC state has been deleted.
Reviewed by: Matt Ahrens <matt@delphix.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Closes#9047
These aren't tunable; illumos has this comment fixed in
"3742 zfs comments need cleaner, more consistent style",
so sync with that.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@gmail.com>
Closes#9052
These functions are unused and can be removed along
with the spl-mutex.c and spl-rwlock.c source files.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Tomohiro Kusumi <kusumi.tomohiro@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9029
The Linux kernel's rwsem's have never provided an interface to
allow a reader to be upgraded to a writer. Historically, this
functionality has been implemented by a SPL wrapper function.
However, this approach depends on internal knowledge of the
rw_semaphore and is therefore rather brittle.
Since the ZFS code must always be able to fallback to rw_exit()
and rw_enter() when an rw_tryupgrade() fails; this functionality
isn't critical. Furthermore, the only potentially performance
sensitive consumer is dmu_zfetch() and no decrease in performance
was observed with this change applied. See the PR comments for
additional testing details.
Therefore, it is being retired to make the build more robust and
to simplify the rwlock implementation.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Tomohiro Kusumi <kusumi.tomohiro@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9029
Commit https://github.com/torvalds/linux/commit/94a9717b updated the
rwsem's owner field to contain additional flags describing the rwsem's
state. Rather then update the wrappers to mask out these bits, the
code no longer relies on the owner stored by the kernel. This does
increase the size of a krwlock_t but it makes the implementation
less sensitive to future kernel changes.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Tomohiro Kusumi <kusumi.tomohiro@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9029
lockdep reports a possible recursive lock in dbuf_destroy.
It is true that dbuf_destroy is acquiring the dn_dbufs_mtx
on one dnode while holding it on another dnode. However,
it is impossible for these to be the same dnode because,
among other things,dbuf_destroy checks MUTEX_HELD before
acquiring the mutex.
This fix defines a class NESTED_SINGLE == 1 and changes
that lock to call mutex_enter_nested with a subclass of
NESTED_SINGLE.
In order to make the userspace code compile,
include/sys/zfs_context.h now defines mutex_enter_nested and
NESTED_SINGLE.
This is the lockdep report:
[ 122.950921] ============================================
[ 122.950921] WARNING: possible recursive locking detected
[ 122.950921] 4.19.29-4.19.0-debug-d69edad5368c1166 #1 Tainted: G O
[ 122.950921] --------------------------------------------
[ 122.950921] dbu_evict/1457 is trying to acquire lock:
[ 122.950921] 0000000083e9cbcf (&dn->dn_dbufs_mtx){+.+.}, at: dbuf_destroy+0x3c0/0xdb0 [zfs]
[ 122.950921]
but task is already holding lock:
[ 122.950921] 0000000055523987 (&dn->dn_dbufs_mtx){+.+.}, at: dnode_evict_dbufs+0x90/0x740 [zfs]
[ 122.950921]
other info that might help us debug this:
[ 122.950921] Possible unsafe locking scenario:
[ 122.950921] CPU0
[ 122.950921] ----
[ 122.950921] lock(&dn->dn_dbufs_mtx);
[ 122.950921] lock(&dn->dn_dbufs_mtx);
[ 122.950921]
*** DEADLOCK ***
[ 122.950921] May be due to missing lock nesting notation
[ 122.950921] 1 lock held by dbu_evict/1457:
[ 122.950921] #0: 0000000055523987 (&dn->dn_dbufs_mtx){+.+.}, at: dnode_evict_dbufs+0x90/0x740 [zfs]
[ 122.950921]
stack backtrace:
[ 122.950921] CPU: 0 PID: 1457 Comm: dbu_evict Tainted: G O 4.19.29-4.19.0-debug-d69edad5368c1166 #1
[ 122.950921] Hardware name: Supermicro H8SSL-I2/H8SSL-I2, BIOS 080011 03/13/2009
[ 122.950921] Call Trace:
[ 122.950921] dump_stack+0x91/0xeb
[ 122.950921] __lock_acquire+0x2ca7/0x4f10
[ 122.950921] lock_acquire+0x153/0x330
[ 122.950921] dbuf_destroy+0x3c0/0xdb0 [zfs]
[ 122.950921] dbuf_evict_one+0x1cc/0x3d0 [zfs]
[ 122.950921] dbuf_rele_and_unlock+0xb84/0xd60 [zfs]
[ 122.950921] dnode_evict_dbufs+0x3a6/0x740 [zfs]
[ 122.950921] dmu_objset_evict+0x7a/0x500 [zfs]
[ 122.950921] dsl_dataset_evict_async+0x70/0x480 [zfs]
[ 122.950921] taskq_thread+0x979/0x1480 [spl]
[ 122.950921] kthread+0x2e7/0x3e0
[ 122.950921] ret_from_fork+0x27/0x50
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jeff Dike <jdike@akamai.com>
Closes#8984
Make use of __GFP_HIGHMEM flag in vmem_alloc, which is required for
some 32-bit systems to make use of full available memory.
While kernel versions >=4.12-rc1 add this flag implicitly, older
kernels do not.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Closes#9031
zfs_refcount_*() are to be wrapped by zfsctl_snapshot_*() in this file.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@gmail.com>
Closes#9039
Resolve an assortment of style inconsistencies including
use of white space, typos, capitalization, and line wrapping.
There is no functional change.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9030
The cast of the size_t returned by strlcpy() to a uint64_t by the
VERIFY3U can result in a build failure when CONFIG_FORTIFY_SOURCE
is set. This is due to the additional hardening. Since the token
is expected to always fit in strval the VERIFY3U has been removed.
If somehow it doesn't, it will still be safely truncated.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Don Brady <don.brady@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #8999Closes#9020
= Motivation
At Delphix we've seen a lot of customer systems where fragmentation
is over 75% and random writes take a performance hit because a lot
of time is spend on I/Os that update on-disk space accounting metadata.
Specifically, we seen cases where 20% to 40% of sync time is spend
after sync pass 1 and ~30% of the I/Os on the system is spent updating
spacemaps.
The problem is that these pools have existed long enough that we've
touched almost every metaslab at least once, and random writes
scatter frees across all metaslabs every TXG, thus appending to
their spacemaps and resulting in many I/Os. To give an example,
assuming that every VDEV has 200 metaslabs and our writes fit within
a single spacemap block (generally 4K) we have 200 I/Os. Then if we
assume 2 levels of indirection, we need 400 additional I/Os and
since we are talking about metadata for which we keep 2 extra copies
for redundancy we need to triple that number, leading to a total of
1800 I/Os per VDEV every TXG.
We could try and decrease the number of metaslabs so we have less
I/Os per TXG but then each metaslab would cover a wider range on
disk and thus would take more time to be loaded in memory from disk.
In addition, after it's loaded, it's range tree would consume more
memory.
Another idea would be to just increase the spacemap block size
which would allow us to fit more entries within an I/O block
resulting in fewer I/Os per metaslab and a speedup in loading time.
The problem is still that we don't deal with the number of I/Os
going up as the number of metaslabs is increasing and the fact
is that we generally write a lot to a few metaslabs and a little
to the rest of them. Thus, just increasing the block size would
actually waste bandwidth because we won't be utilizing our bigger
block size.
= About this patch
This patch introduces the Log Spacemap project which provides the
solution to the above problem while taking into account all the
aforementioned tradeoffs. The details on how it achieves that can
be found in the references sections below and in the code (see
Big Theory Statement in spa_log_spacemap.c).
Even though the change is fairly constraint within the metaslab
and lower-level SPA codepaths, there is a side-change that is
user-facing. The change is that VDEV IDs from VDEV holes will no
longer be reused. To give some background and reasoning for this,
when a log device is removed and its VDEV structure was replaced
with a hole (or was compacted; if at the end of the vdev array),
its vdev_id could be reused by devices added after that. Now
with the pool-wide space maps recording the vdev ID, this behavior
can cause problems (e.g. is this entry referring to a segment in
the new vdev or the removed log?). Thus, to simplify things the
ID reuse behavior is gone and now vdev IDs for top-level vdevs
are truly unique within a pool.
= Testing
The illumos implementation of this feature has been used internally
for a year and has been in production for ~6 months. For this patch
specifically there don't seem to be any regressions introduced to
ZTS and I have been running zloop for a week without any related
problems.
= Performance Analysis (Linux Specific)
All performance results and analysis for illumos can be found in
the links of the references. Redoing the same experiments in Linux
gave similar results. Below are the specifics of the Linux run.
After the pool reached stable state the percentage of the time
spent in pass 1 per TXG was 64% on average for the stock bits
while the log spacemap bits stayed at 95% during the experiment
(graph: sdimitro.github.io/img/linux-lsm/PercOfSyncInPassOne.png).
Sync times per TXG were 37.6 seconds on average for the stock
bits and 22.7 seconds for the log spacemap bits (related graph:
sdimitro.github.io/img/linux-lsm/SyncTimePerTXG.png). As a result
the log spacemap bits were able to push more TXGs, which is also
the reason why all graphs quantified per TXG have more entries for
the log spacemap bits.
Another interesting aspect in terms of txg syncs is that the stock
bits had 22% of their TXGs reach sync pass 7, 55% reach sync pass 8,
and 20% reach 9. The log space map bits reached sync pass 4 in 79%
of their TXGs, sync pass 7 in 19%, and sync pass 8 at 1%. This
emphasizes the fact that not only we spend less time on metadata
but we also iterate less times to convergence in spa_sync() dirtying
objects.
[related graphs:
stock- sdimitro.github.io/img/linux-lsm/NumberOfPassesPerTXGStock.png
lsm- sdimitro.github.io/img/linux-lsm/NumberOfPassesPerTXGLSM.png]
Finally, the improvement in IOPs that the userland gains from the
change is approximately 40%. There is a consistent win in IOPS as
you can see from the graphs below but the absolute amount of
improvement that the log spacemap gives varies within each minute
interval.
sdimitro.github.io/img/linux-lsm/StockVsLog3Days.png
sdimitro.github.io/img/linux-lsm/StockVsLog10Hours.png
= Porting to Other Platforms
For people that want to port this commit to other platforms below
is a list of ZoL commits that this patch depends on:
Make zdb results for checkpoint tests consistent
db587941c5
Update vdev_is_spacemap_addressable() for new spacemap encoding
419ba59145
Simplify spa_sync by breaking it up to smaller functions
8dc2197b7b
Factor metaslab_load_wait() in metaslab_load()
b194fab0fb
Rename range_tree_verify to range_tree_verify_not_present
df72b8bebe
Change target size of metaslabs from 256GB to 16GB
c853f382db
zdb -L should skip leak detection altogether
21e7cf5da8
vs_alloc can underflow in L2ARC vdevs
7558997d2f
Simplify log vdev removal code
6c926f426a
Get rid of space_map_update() for ms_synced_length
425d3237ee
Introduce auxiliary metaslab histograms
928e8ad47d
Error path in metaslab_load_impl() forgets to drop ms_sync_lock
8eef997679
= References
Background, Motivation, and Internals of the Feature
- OpenZFS 2017 Presentation:
youtu.be/jj2IxRkl5bQ
- Slides:
slideshare.net/SerapheimNikolaosDim/zfs-log-spacemaps-project
Flushing Algorithm Internals & Performance Results
(Illumos Specific)
- Blogpost:
sdimitro.github.io/post/zfs-lsm-flushing/
- OpenZFS 2018 Presentation:
youtu.be/x6D2dHRjkxw
- Slides:
slideshare.net/SerapheimNikolaosDim/zfs-log-spacemap-flushing-algorithm
Upstream Delphix Issues:
DLPX-51539, DLPX-59659, DLPX-57783, DLPX-61438, DLPX-41227, DLPX-59320
DLPX-63385
Reviewed-by: Sean Eric Fagan <sef@ixsystems.com>
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Closes#8442
ZFS_ACLTYPE_POSIXACL has already been tested in zpl_init_acl(),
so no need to test again on POSIX ACL access.
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@gmail.com>
Closes#9009
External consumers such as Lustre require access to the dnode
interfaces in order to correctly manipulate dnodes.
Reviewed-by: James Simmons <uja.ornl@yahoo.com>
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #8994Closes#9027
This patch corrects a small issue where the dsl_destroy_head()
code that runs when the async_destroy feature is disabled would
not properly decrypt the dataset before beginning processing.
If the dataset is not able to be decrypted, the optimization
code now simply does not run and the dataset is completely
destroyed in the DSL sync task.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#9021
struct pathname is originally from Solaris VFS, and it has been used
in ZoL to merely call VOP from Linux VFS interface without API change,
therefore pathname::pn_path* are unused and unneeded. Technically,
struct pathname is a wrapper for C string in ZoL.
Saves stack a bit on lookup and unlink.
(#if0'd members instead of removing since comments refer to them.)
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@gmail.com>
Closes#9025
Restore the SIMD optimization for 4.19.38 LTS, 4.14.120 LTS,
and 5.0 and newer kernels. This is accomplished by leveraging
the fact that by definition dedicated kernel threads never need
to concern themselves with saving and restoring the user FPU state.
Therefore, they may use the FPU as long as we can guarantee user
tasks always restore their FPU state before context switching back
to user space.
For the 5.0 and 5.1 kernels disabling preemption and local
interrupts is sufficient to allow the FPU to be used. All non-kernel
threads will restore the preserved user FPU state.
For 5.2 and latter kernels the user FPU state restoration will be
skipped if the kernel determines the registers have not changed.
Therefore, for these kernels we need to perform the additional
step of saving and restoring the FPU registers. Invalidating the
per-cpu global tracking the FPU state would force a restore but
that functionality is private to the core x86 FPU implementation
and unavailable.
In practice, restricting SIMD to kernel threads is not a major
restriction for ZFS. The vast majority of SIMD operations are
already performed by the IO pipeline. The remaining cases are
relatively infrequent and can be handled by the generic code
without significant impact. The two most noteworthy cases are:
1) Decrypting the wrapping key for an encrypted dataset,
i.e. `zfs load-key`. All other encryption and decryption
operations will use the SIMD optimized implementations.
2) Generating the payload checksums for a `zfs send` stream.
In order to avoid making any changes to the higher layers of ZFS
all of the `*_get_ops()` functions were updated to take in to
consideration the calling context. This allows for the fastest
implementation to be used as appropriate (see kfpu_allowed()).
The only other notable instance of SIMD operations being used
outside a kernel thread was at module load time. This code
was moved in to a taskq in order to accommodate the new kernel
thread restriction.
Finally, a few other modifications were made in order to further
harden this code and facilitate testing. They include updating
each implementations operations structure to be declared as a
constant. And allowing "cycle" to be set when selecting the
preferred ops in the kernel as well as user space.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8754Closes#8793Closes#8965
Large allocation over the spl_kmem_alloc_warn value was being performed.
Switched to vmem_alloc interface as specified for large allocations.
Changed the subsequent frees to match.
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: nmattis <nickm970@gmail.com>
Closes#8934Closes#9011
Currently, sequential async write workloads spend a lot of time
contending on the dn_struct_rwlock. This lock is responsible for
protecting the entire block tree below it; this naturally results
in some serialization during heavy write workloads. This can be
resolved by having per-dbuf locking, which will allow multiple
writers in the same object at the same time.
We introduce a new rwlock, the db_rwlock. This lock is responsible
for protecting the contents of the dbuf that it is a part of; when
reading a block pointer from a dbuf, you hold the lock as a reader.
When writing data to a dbuf, you hold it as a writer. This allows
multiple threads to write to different parts of a file at the same
time.
Reviewed by: Brad Lewis <brad.lewis@delphix.com>
Reviewed by: Matt Ahrens matt@delphix.com
Reviewed by: George Wilson george.wilson@delphix.com
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
External-issue: DLPX-52564
External-issue: DLPX-53085
External-issue: DLPX-57384
Closes#8946
ZFS tracing efforts are hampered by the inability to access zfs static
probes(probes using DTRACE_PROBE macros). The probes are available via
tracepoints for GPL modules only. The build could be modified to
generate a function for each unique DTRACE_PROBE invocation. These could
be then accessed via kprobes.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Signed-off-by: Brad Lewis <brad.lewis@delphix.com>
Closes#8659Closes#8663
This reverts commit aa7aab6c45.
The change is not compatible with CentOS 6's 2.6.32 based kernel
due to differnces in the bio layer.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #8961
This patch fixes an issue where dsl_dataset_crypt_stats() would
VERIFY that it was able to hold the encryption root. This function
should instead silently continue without populating the related
field in the nvlist, as is the convention for this code.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#8976
We return ENOSPC in metaslab_activate if the metaslab has weight 0,
to avoid activating a metaslab with no space available. For sanity
checking, we also assert that there is no free space in the range
tree in that case.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed by: Matt Ahrens <matt@delphix.com>
Reviewed by: Serapheim Dimitropoulos <serapheim.dimitro@delphix.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#8968
Having the mountpoint and dataset name both in the message made it
confusing to read. Additionally, convert this to a zfs_dbgmsg rather than
sending it to the console.
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Zuchowski <pzuchowski@datto.com>
Closes#8959
Unable to import zpool with "Large kmem_alloc" warning due to
corrupted bio's with invalid # of page vectors.
See #8867 for details.
Fail early with ENOMEM.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@gmail.com>
Closes#8867Closes#8961
The b_freeze_cksum field can only have data when ZFS_DEBUG_MODIFY
is set. Therefore, the EQUIV check must be wrapped accordingly.
For the same reason the ASSERT in arc_buf_fill() in unsafe.
However, since it's largely redundant it has simply been removed.
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Allan Jude <allanjude@freebsd.org>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8979
Chroot'd process fails to automount snapshots due to realpath(3)
failure in mount.zfs(8).
Construct a mount point path from sb of the ctldir inode and dirent
name, instead of from d_path(), so that chroot'd process doesn't get
affected by its view of fs.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@gmail.com>
Closes#8903Closes#8966
After device removal, performing nopwrites on a dmu_sync-ed block
will result in a panic. This panic can show up in two ways:
1. an attempt to issue an IOCTL in vdev_indirect_io_start()
2. a failed comparison of zio->io_bp and zio->io_bp_orig in
zio_done()
To resolve both of these panics, nopwrites of blocks on indirect
vdevs should be ignored and new allocations should be performed on
concrete vdevs.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Don Brady <don.brady@delphix.com>
Signed-off-by: George Wilson <gwilson@delphix.com>
Closes#8957
With the new parallel allocators scheme, there is a possibility for
a problem where two threads, allocating from the same allocator at
the same time, conflict with each other. There are two primary cases
to worry about. First, another thread working on another allocator
activates the same metaslab that the first thread was trying to
activate. This results in the first thread needing to go back and
reselect a new metaslab, even though it may have waited a long time
for this metaslab to load. Second, another thread working on the same
allocator may have activated a different metaslab while the first
thread was waiting for its metaslab to load. Both of these cases
can cause the first thread to be significantly delayed in issuing
its IOs. The second case can also cause metaslab load/unload churn;
because the metaslab is loaded but not fully activated, we never set
the selected_txg, which results in the metaslab being immediately
unloaded again. This process can repeat many times, wasting disk and
cpu resources. This is more likely to happen when the IO of the first
thread is a larger one (like a ZIL write) and the other thread is
doing a smaller write, because it is more likely to find an
acceptable metaslab quickly.
There are two primary changes. The first is to always proceed with
the allocation when returning from metaslab_activate if we were
preempted in either of the ways described in the previous section.
The second change is to set the selected_txg before we do the call
to activate so that even if the metaslab is not used for an
allocation, we won't immediately attempt to unload it.
Reviewed by: Jerry Jelinek <jerry.jelinek@joyent.com>
Reviewed by: Matt Ahrens <matt@delphix.com>
Reviewed by: Serapheim Dimitropoulos <serapheim.dimitro@delphix.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
External-issue: DLPX-61314
Closes#8843
DMU sync code calls taskq_dispatch() for each sublist of os_dirty_dnodes
and os_synced_dnodes. Since the number of sublists by default is equal
to number of CPUs, it will dispatch equal, potentially large, number of
tasks, waking up many CPUs to handle them, even if only one or few of
sublists actually have any work to do.
This change adds check for empty sublists to avoid this.
Reviewed by: Sean Eric Fagan <sef@ixsystems.com>
Reviewed by: Matt Ahrens <matt@delphix.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#8909
With the addition of BP_EMBEDDED_TYPE_REDACTED in 30af21b0 a couple of
codepaths make wrong assumptions and could potentially result in errors.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Chris Dunlop <chris@onthe.net.au>
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#8951
The "zfs remap" command was disabled by
6e91a72fe3, because it has little utility
and introduced some tricky bugs. This commit removes the code for it,
the associated ZFS_IOC_REMAP ioctl, and tests.
Note that the ioctl and property will remain, but have no functionality.
This allows older software to fail gracefully if it attempts to use
these, and avoids a backwards incompatibility that would be introduced if
we renumbered the later ioctls/props.
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#8944
This patch corrects the error message reported when attempting
to promote a dataset outside of its encryption root.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#8905Closes#8935
Resolve the incorrect use of srcdir and builddir references for
various files in the build system. These have crept in over time
and went unnoticed because when building in the top level directory
srcdir and builddir are identical.
With this change it's again possible to build in a subdirectory.
$ mkdir obj
$ cd obj
$ ../configure
$ make
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Don Brady <don.brady@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8921Closes#8943
Problem Statement
=================
ZFS Channel program scripts currently require a timeout, so that hung or
long-running scripts return a timeout error instead of causing ZFS to get
wedged. This limit can currently be set up to 100 million Lua instructions.
Even with a limit in place, it would be desirable to have a sys admin
(support engineer) be able to cancel a script that is taking a long time.
Proposed Solution
=================
Make it possible to abort a channel program by sending an interrupt signal.In
the underlying txg_wait_sync function, switch the cv_wait to a cv_wait_sig to
catch the signal. Once a signal is encountered, the dsl_sync_task function can
install a Lua hook that will get called before the Lua interpreter executes a
new line of code. The dsl_sync_task can resume with a standard txg_wait_sync
call and wait for the txg to complete. Meanwhile, the hook will abort the
script and indicate that the channel program was canceled. The kernel returns
a EINTR to indicate that the channel program run was canceled.
Porting notes: Added missing return value from cv_wait_sig()
Authored by: Don Brady <don.brady@delphix.com>
Reviewed by: Sebastien Roy <sebastien.roy@delphix.com>
Reviewed by: Serapheim Dimitropoulos <serapheim.dimitro@delphix.com>
Reviewed by: Matt Ahrens <matt@delphix.com>
Reviewed by: Sara Hartse <sara.hartse@delphix.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Robert Mustacchi <rm@joyent.com>
Ported-by: Don Brady <don.brady@delphix.com>
Signed-off-by: Don Brady <don.brady@delphix.com>
OpenZFS-issue: https://www.illumos.org/issues/9425
OpenZFS-commit: https://github.com/illumos/illumos-gate/commit/d0cb1fb926Closes#8904
The thread calling dmu_tx_try_assign() can't hold the dn_struct_rwlock
while assigning the tx, because this can lead to deadlock. Specifically,
if this dnode is already assigned to an earlier txg, this thread may
need to wait for that txg to sync (the ERESTART case below). The other
thread that has assigned this dnode to an earlier txg prevents this txg
from syncing until its tx can complete (calling dmu_tx_commit()), but it
may need to acquire the dn_struct_rwlock to do so (e.g. via
dmu_buf_hold*()).
This commit adds an assertion to dmu_tx_try_assign() to ensure that this
deadlock is not inadvertently introduced.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#8929
When exporting ZVOLs as SCSI LUNs, by default Windows will not
issue them UNMAP commands. This reduces storage efficiency in
many cases.
We add the SCSI_PASSTHROUGH flag to the zvol's device queue,
which lets the SCSI target logic know that it can handle SCSI
commands.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: John Gallagher <john.gallagher@delphix.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#8933
`show_str` could be a pointer to a local variable in stack
which is out-of-scope by the time
`return (snprintf(buf, buflen, "%s\n", show_str));`
is called.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@gmail.com>
Closes#8924Closes#8940
The logic to handle strong checksum collisions where the data doesn't
match is incorrect. It is not clearing the dedup bit of the blkptr,
which can cause a panic later in zio_ddt_free() due to the dedup table
not matching what is in the blkptr.
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
External-issue: DLPX-48097
Closes#8936
Align vdev_ops_t from illumos for better compatibility.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Igor Kozhukhov <igor@dilos.org>
Closes#8925
When encryption was first added to ZFS, we made a decision to
prevent users from creating unencrypted children of encrypted
datasets. The idea was to prevent users from inadvertently
leaving some of their data unencrypted. However, since the
release of 0.8.0, some legitimate reasons have been brought up
for this behavior to be allowed. This patch simply removes this
limitation from all code paths that had checks for it and updates
the tests accordingly.
Reviewed-by: Jason King <jason.king@joyent.com>
Reviewed-by: Sean Eric Fagan <sef@ixsystems.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#8737Closes#8870
If dedup is in use, the `dedupditto` property can be set, causing ZFS to
keep an extra copy of data that is referenced many times (>100x). The
idea was that this data is more important than other data and thus we
want to be really sure that it is not lost if the disk experiences a
small amount of random corruption.
ZFS (and system administrators) rely on the pool-level redundancy to
protect their data (e.g. mirroring or RAIDZ). Since the user/sysadmin
doesn't have control over what data will be offered extra redundancy by
dedupditto, this extra redundancy is not very useful. The bulk of the
data is still vulnerable to loss based on the pool-level redundancy.
For example, if particle strikes corrupt 0.1% of blocks, you will either
be saved by mirror/raidz, or you will be sad. This is true even if
dedupditto saved another 0.01% of blocks from being corrupted.
Therefore, the dedupditto functionality is rarely enabled (i.e. the
property is rarely set), and it fulfills its promise of increased
redundancy even more rarely.
Additionally, this feature does not work as advertised (on existing
releases), because scrub/resilver did not repair the extra (dedupditto)
copy (see https://github.com/zfsonlinux/zfs/pull/8270).
In summary, this seldom-used feature doesn't work, and even if it did it
wouldn't provide useful data protection. It has a non-trivial
maintenance burden (again see https://github.com/zfsonlinux/zfs/pull/8270).
We should remove the dedupditto functionality. For backwards
compatibility with the existing CLI, "zpool set dedupditto" will still
"succeed" (exit code zero), but won't have any effect. For backwards
compatibility with existing pools that had dedupditto enabled at some
point, the code will still be able to understand dedupditto blocks and
free them when appropriate. However, ZFS won't write any new dedupditto
blocks.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Alek Pinchuk <apinchuk@datto.com>
Issue #8270Closes#8310
Redacted send/receive allows users to send subsets of their data to
a target system. One possible use case for this feature is to not
transmit sensitive information to a data warehousing, test/dev, or
analytics environment. Another is to save space by not replicating
unimportant data within a given dataset, for example in backup tools
like zrepl.
Redacted send/receive is a three-stage process. First, a clone (or
clones) is made of the snapshot to be sent to the target. In this
clone (or clones), all unnecessary or unwanted data is removed or
modified. This clone is then snapshotted to create the "redaction
snapshot" (or snapshots). Second, the new zfs redact command is used
to create a redaction bookmark. The redaction bookmark stores the
list of blocks in a snapshot that were modified by the redaction
snapshot(s). Finally, the redaction bookmark is passed as a parameter
to zfs send. When sending to the snapshot that was redacted, the
redaction bookmark is used to filter out blocks that contain sensitive
or unwanted information, and those blocks are not included in the send
stream. When sending from the redaction bookmark, the blocks it
contains are considered as candidate blocks in addition to those
blocks in the destination snapshot that were modified since the
creation_txg of the redaction bookmark. This step is necessary to
allow the target to rehydrate data in the case where some blocks are
accidentally or unnecessarily modified in the redaction snapshot.
The changes to bookmarks to enable fast space estimation involve
adding deadlists to bookmarks. There is also logic to manage the
life cycles of these deadlists.
The new size estimation process operates in cases where previously
an accurate estimate could not be provided. In those cases, a send
is performed where no data blocks are read, reducing the runtime
significantly and providing a byte-accurate size estimate.
Reviewed-by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: Prashanth Sreenivasa <pks@delphix.com>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: George Wilson <george.wilson@delphix.com>
Reviewed-by: Chris Williamson <chris.williamson@delphix.com>
Reviewed-by: Pavel Zhakarov <pavel.zakharov@delphix.com>
Reviewed-by: Sebastien Roy <sebastien.roy@delphix.com>
Reviewed-by: Prakash Surya <prakash.surya@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#7958
For busy ARC situation when arc_size close to arc_c is desired. But
then it is quite likely that aggsum_compare(&arc_size, arc_c) will need
to flush per-CPU buckets to find exact comparison result. Doing that
often in a hot path penalizes whole idea of aggsum usage there, since it
replaces few simple atomic additions with dozens of lock acquisitions.
Replacing aggsum_compare() with aggsum_upper_bound() in code increasing
arc_p when ARC is growing (arc_size < arc_c) according to PMC profiles
allows to save ~5% of CPU time in aggsum code during sequential write
to 12 ZVOLs with 16KB block size on large dual-socket system.
I suppose there some minor arc_p behavior change due to lower precision
of the new code, but I don't think it is a big deal, since it should
affect only very small window in time (aggsum buckets are flushed every
second) and in ARC size (buckets are limited to 10 average ARC blocks
per CPU).
Reviewed-by: Chris Dunlop <chris@onthe.net.au>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Allan Jude <allanjude@freebsd.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#8901
If the zfs_remove_max_segment tunable is changed to be not a multiple of
the sector size, then the device removal code will malfunction and try
to create mappings that are smaller than one sector, leading to a panic.
On debug bits this assertion will fail in spa_vdev_copy_segment():
ASSERT3U(DVA_GET_ASIZE(&dst), ==, size);
On nondebug, the system panics with a stack like:
metaslab_free_concrete()
metaslab_free_impl()
metaslab_free_impl_cb()
vdev_indirect_remap()
free_from_removing_vdev()
metaslab_free_impl()
metaslab_free_dva()
metaslab_free()
Fortunately, the default for zfs_remove_max_segment is 1MB, so this
can't occur by default. We hit it during this test because
removal_remap.ksh changes zfs_remove_max_segment to 1KB. When testing on
4KB-sector disks, we hit the bug.
This change makes the zfs_remove_max_segment tunable more robust,
automatically rounding it up to a multiple of the sector size. We also
turn some key assertions into VERIFY's so that similar bugs would be
caught before they are encoded on disk (and thus avoid a
panic-reboot-loop).
Reviewed-by: Sean Eric Fagan <sef@ixsystems.com>
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: Sebastien Roy <sebastien.roy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
External-issue: DLPX-61342
Closes#8893
Starting in sync pass 5 (zfs_sync_pass_dont_compress), we disable
compression (including of metadata). Ostensibly this helps the sync
passes to converge (i.e. for a sync pass to not need to allocate
anything because it is 100% overwrites).
However, in practice it increases the average number of sync passes,
because when we turn compression off, a lot of block's size will change
and thus we have to re-allocate (not overwrite) them. It also increases
the number of 128KB allocations (e.g. for indirect blocks and spacemaps)
because these will not be compressed. The 128K allocations are
especially detrimental to performance on highly fragmented systems,
which may have very few free segments of this size, and may need to load
new metaslabs to satisfy 128K allocations.
We should increase zfs_sync_pass_dont_compress. In practice on a highly
fragmented system we see a few 5-pass txg's, a tiny number of 6-pass
txg's, and no txg's with more than 6 passes.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: George Wilson <george.wilson@delphix.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
External-issue: DLPX-63431
Closes#8892
Memory copy is too heavy operation to do under the congested lock.
Moving it out reduces congestion by many times to almost invisible.
Since the original zio removed from the queue, and the child zio is
not executed yet, I don't see why would the copy need protection.
My guess it just remained like this from the time when lock was not
dropped here, which was added later to fix lock ordering issue.
Multi-threaded sequential write tests with both HDD and SSD pools
with ZVOL block sizes of 4KB, 16KB, 64KB and 128KB all show major
reduction of lock congestion, saving from 15% to 35% of CPU time
and increasing throughput from 10% to 40%.
Reviewed-by: Richard Yao <ryao@gentoo.org>
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#8890
On fragmented pools with high-performance storage, the looping in
metaslab_block_picker() can become the performance-limiting bottleneck.
When looking for a larger block (e.g. a 128K block for the ZIL), we may
search through many free segments (up to hundreds of thousands) to find
one that is large enough to satisfy the allocation. This can take a long
time (up to dozens of ms), and is done while holding the ms_lock, which
other threads may spin waiting for.
When this performance problem is encountered, profiling will show
high CPU time in metaslab_block_picker, as well as in mutex_enter from
various callers.
The problem is very evident on a test system with a sync write workload
with 8K writes to a recordsize=8k filesystem, with 4TB of SSD storage,
84% full and 88% fragmented. It has also been observed on production
systems with 90TB of storage, 76% full and 87% fragmented.
The fix is to change metaslab_df_alloc() to search only up to 16MB from
the previous allocation (of this alignment). After that, we will pick a
segment that is of the exact size requested (or larger). This reduces
the number of iterations to a few hundred on fragmented pools (a ~100x
improvement).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: George Wilson <george.wilson@delphix.com>
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
External-issue: DLPX-62324
Closes#8877
This change restricts filesystem creation if the given name
contains either '.' or '..'
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Signed-off-by: TulsiJain <tulsi.jain@delphix.com>
Closes#8842Closes#8564
When running zloop, we occasionally see the following crash:
dmu_tx_assign(tx, TXG_WAIT) == 0 (0x1c == 0)
ASSERT at ../../module/zfs/vdev_removal.c:1507:spa_vdev_remove_thread()/sbin/ztest(+0x89c3)[0x55faf567b9c3]
The error value 0x1c is ENOSPC.
The transaction used by spa_vdev_remove_thread() should not be able to
fail due to being out of space. i.e. we should not call
dmu_tx_hold_space(). This will allow the removal thread to schedule its
work even when the pool is low on space. The "slop space" will provide
enough free space to sync out the txg.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
External-issue: DLPX-37853
Closes#8889
sysfs_attr_init() is required to make lockdep happy for dynamically
allocated sysfs attributes. This fixed#8868 on Fedora 29 running
kernel-debug.
This requirement was introduced in 2.6.34.
See include/linux/sysfs.h for what it actually does.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@gmail.com>
Closes#8868Closes#8884
When iterating over a ZAP object, we're almost always certain to iterate
over the entire object. If there are multiple leaf blocks, we can
realize a performance win by issuing reads for all the leaf blocks in
parallel when the iteration begins.
For example, if we have 10,000 snapshots, "zfs destroy -nv
pool/fs@1%9999" can take 30 minutes when the cache is cold. This change
provides a >3x performance improvement, by issuing the reads for all ~64
blocks of each ZAP object in parallel.
Reviewed-by: Andreas Dilger <andreas.dilger@whamcloud.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
External-issue: DLPX-58347
Closes#8862
Sometimes the target ARC size is reduced to arc_c_min, which impacts
performance. We've seen this happen as part of the random_reads
performance regression test, where the ARC size is reduced before the
reads test starts which impacts how long it takes for system to reach
good IOPS performance.
We call arc_reduce_target_size when arc_reap_cb_check() returns TRUE,
and arc_available_memory() is less than arc_c>>arc_shrink_shift.
However, arc_available_memory() could easily be low, even when arc_c is
low, because we can have tons of unused bufs in the abd kmem cache. This
would be especially true just after the DMU requests a bunch of stuff be
evicted from the ARC (e.g. due to "zpool export").
To fix this, the ARC should reduce arc_c by the requested amount, not
all the way down to arc_size (or arc_c_min), which can be very small.
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
External-issue: DLPX-59431
Closes#8864
Scatter ABD's are allocated from a number of pages. In contrast to
linear ABD's, these pages are disjoint in the kernel's virtual address
space, so they can't be accessed as a contiguous buffer. Therefore
routines that need a linear buffer (e.g. abd_borrow_buf() and friends)
must allocate a separate linear buffer (with zio_buf_alloc()), and copy
the contents of the pages to/from the linear buffer. This can have a
measurable performance overhead on some workloads.
https://github.com/zfsonlinux/zfs/commit/87c25d567fb7969b44c7d8af63990e
("abd_alloc should use scatter for >1K allocations") increased the use
of scatter ABD's, specifically switching 1.5K through 4K (inclusive)
buffers from linear to scatter. For workloads that access blocks whose
compressed sizes are in this range, that commit introduced an additional
copy into the read code path. For example, the
sequential_reads_arc_cached tests in the test suite were reduced by
around 5% (this is doing reads of 8K-logical blocks, compressed to 3K,
which are cached in the ARC).
This commit treats single-chunk scattered buffers as linear buffers,
because they are contiguous in the kernel's virtual address space.
All single-page (4K) ABD's can be represented this way. Some multi-page
ABD's can also be represented this way, if we were able to allocate a
single "chunk" (higher-order "page" which represents a power-of-2 series
of physically-contiguous pages). This is often the case for 2-page (8K)
ABD's.
Representing a single-entry scatter ABD as a linear ABD has the
performance advantage of avoiding the copy (and allocation) in
abd_borrow_buf_copy / abd_return_buf_copy. A performance increase of
around 5% has been observed for ARC-cached reads (of small blocks which
can take advantage of this), fixing the regression introduced by
87c25d567.
Note that this optimization is only possible because all physical memory
is always mapped into the kernel's address space. This is not the case
for HIGHMEM pages, so the optimization can not be made on 32-bit
systems.
Reviewed-by: Chunwei Chen <tuxoko@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#8580
We've observed that on some highly fragmented pools, most metaslab
allocations are small (~2-8KB), but there are some large, 128K
allocations. The large allocations are for ZIL blocks. If there is a
lot of fragmentation, the large allocations can be hard to satisfy.
The most common impact of this is that we need to check (and thus load)
lots of metaslabs from the ZIL allocation code path, causing sync writes
to wait for metaslabs to load, which can take a second or more. In the
worst case, we may not be able to satisfy the allocation, in which case
the ZIL will resort to txg_wait_synced() to ensure the change is on
disk.
To provide a workaround for this, this change adds a tunable that can
reduce the size of ZIL blocks.
External-issue: DLPX-61719
Reviewed-by: George Wilson <george.wilson@delphix.com>
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#8865
When ARC size is very small, aggsum_lower_bound(&arc_size) may return
negative values, that due to unsigned comparison caused delays, waiting
for arc_adjust() to "fix" it by calling aggsum_value(&arc_size). Use
of signed comparison there fixes the problem.
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#8873
This patch fixes an incorrect error message that comes up when
doing a non-forcing, raw, incremental receive into a dataset
that has a newer snapshot than the "from" snapshot. In this
case, the current code prints a confusing message about an IVset
guid mismatch.
This functionality is supported by non-raw receives as an
undocumented feature, but was never supported by the raw receive
code. If this is desired in the future, we can probably figure
out a way to make it work.
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Issue #8758Closes#8863
On large systems, the memory used by loaded metaslabs can become
a concern. While range trees are a fairly efficient data structure,
on heavily fragmented pools they can still consume a significant
amount of memory. This problem is amplified when we fail to unload
metaslabs that we aren't using. Currently, we only unload a metaslab
during metaslab_sync_done; in order for that function to be called
on a given metaslab in a given txg, we have to have dirtied that
metaslab in that txg. If the dirtying was the result of an allocation,
we wouldn't be unloading it (since it wouldn't be 8 txgs since it
was selected), so in effect we only unload a metaslab during txgs
where it's being freed from.
We move the unload logic from sync_done to a new function, and
call that function on all metaslabs in a given vdev during
vdev_sync_done().
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#8837
This patch re-adds a check that was removed in 369aa50. The check
confirms that a raw receive is not occuring before truncating an
object's dn_maxblkid. At the time, it was believed that all cases
that would hit this code path would be handled in other places,
but that was not the case.
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#8852Closes#8857
Reviewed-by: Chris Dunlop <chris@onthe.net.au>
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Signed-off-by: Allan Jude <allanjude@freebsd.org>
Closes#8822
Historically while doing performance testing we've noticed that IOPS
can be significantly reduced when all vdevs in the pool are hitting
the zfs_mg_fragmentation_threshold percentage. Specifically in a
hypothetical pool with two vdevs, what can happen is the following:
Vdev A would go above that threshold and only vdev B would be used.
Then vdev B would pass that threshold but vdev A would go below it
(we've been freeing from A to allocate to B). The allocations would
go back and forth utilizing one vdev at a time with IOPS taking a hit.
Empirically, we've seen that our vdev selection for allocations is
good enough that fragmentation increases uniformly across all vdevs
the majority of the time. Thus we set the threshold percentage high
enough to avoid hitting the speed bump on pools that are being pushed
to the edge. We effectively disable its effect in the majority of the
cases but we don't remove (at least for now) just in case we hit any
weird behavior in the future.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Signed-off-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Closes#8859
The ZFS on-disk format stores each inode's generation ID as a 64
bit number on disk and in-core. However, the Linux kernel's inode
is only a 32 bit number. In most places, the code handles this
correctly, but the cast is missing in zfs_rezget(). For many pools,
this isn't an issue since the generation ID is computed as the
current txg when the inode is created and many pools don't have
more than 2^32 txgs.
For the pools that have more txgs, this issue causes any inode with
a high enough generation number to report IO errors after a call to
"zfs rollback" while holding the file or directory open. This patch
simply adds the missing cast.
Reviewed-by: Alek Pinchuk <apinchuk@datto.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#8858
Since zfs_znode_alloc() already takes dmu_buf_t*, taking another
uint64_t argument for objid is redundant. inode's ->i_ino does and
needs to match znode's ->z_id.
zfs_znode_alloc() in FreeBSD and illumos doesn't have this argument
since vnode doesn't have vnode# in VFS (hence ->z_id exists).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@osnexus.com>
Closes#8841
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: DHE <git@dehacked.net>
Closes#8733Closes#8752
This reverts commit ec4f9b8f30 which introduced a narrow race which
can lead to lseek(, SEEK_DATA) incorrectly returning ENXIO. Resolve
the issue by revering this change to restore the previous behavior
which depends solely on checking the dirty list.
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8816Closes#8834
Per suggestion from @behlendorf in #8777, remove vn_set_fs_pwd() and
vn_set_pwd() which are only used in zfs_ioctl.c:_init() while loading
zfs.ko.
The rest of initialization functions being called here after cwd set
to / don't depend on cwd of the process except for spa_config_load().
spa_config_load() uses a relative path ".//etc/zfs/zpool.cache" when
`rootdir` is non-NULL, which is "/etc/zfs/zpool.cache" given cwd is /,
so just unconditionally use the absolute path without "./", so that
`vn_set_pwd("/")` as well as the entire functions can be removed.
This is also what FreeBSD does.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@osnexus.com>
Closes#8826
When opening a log device during import its allocation bias will
not yet have been set by vdev_load(). This results in the log
device's ashift being incorrectly applied to the maximum ashift
of the vdevs in the normal class. Which in turn prevents the
removal of any top-level devices due to the ashift check in the
spa_vdev_remove_top_check() function.
This issue is resolved by including vdev_islog in the check since
it will be set correctly during vdev_open().
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8735
dn->dn_datablksz type is uint32_t and need to be casted to uint64_t
to avoid an overflow when the record size is greater than 4 MiB.
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olivier Mazouffre <olivier.mazouffre@ims-bordeaux.fr>
Closes#8778Closes#8797
This commits fixes a double-free in zfs_ioc_pool_create() triggered by
specifying an unsupported combination of properties when creating a pool
with encryption enabled.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#8791
These descriptions are not uptodate with the code.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@gmail.com>
Closes#8767
Currently, count_block() does not correctly account for the
possibility that the bp that is passed to it could be embedded.
These blocks shouldn't be counted since the work of scanning
these blocks in already handled when the containing block is
scanned. This patch simply resolves this issue by returning
early in this case.
Reviewed by: Allan Jude <allanjude@freebsd.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Authored-by: Bill Sommerfeld <sommerfeld@alum.mit.edu>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#8800Closes#8766
wait_on_page_writeback() was made GPL only in torvalds/linux@19343b5bdd.
Directly call wait_on_page_bit() without using wait_on_page_writeback()
interface, given zfs_putpage() is the only caller for now.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@osnexus.com>
Closes#8794
This failed on 5.2-rc1 with "error: unknown" message, for set_fs_pwd()
not being visible in both const and non-const tests.
This is caused by torvalds/linux@83da1bed86. It's configurable,
but we would want to be able to compile with default kbuild setting.
set_fs_pwd() has never been exported with exception of some distro
kernels, and set_fs_pwd() wasn't used in ZoL to begin with. The test
result was used for a spl function vn_set_fs_pwd().
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@osnexus.com>
Closes#8777
The issue is caused by an incorrect usage of the sizeof() operator
in vdev_obsolete_sm_object(): on 64-bit systems this is not an issue
since both "uint64_t" and "uint64_t*" are 8 bytes in size. However on
32-bit systems pointers are 4 bytes long which is not supported by
zap_lookup_impl(). Trying to remove a top-level vdev on a 32-bit system
will cause the following failure:
VERIFY3(0 == vdev_obsolete_sm_object(vd, &obsolete_sm_object)) failed (0 == 22)
PANIC at vdev_indirect.c:833:vdev_indirect_sync_obsolete()
Showing stack for process 1315
CPU: 6 PID: 1315 Comm: txg_sync Tainted: P OE 4.4.69+ #2
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-2.fc27 04/01/2014
c1abc6e7 0ae10898 00000286 d4ac3bc0 c14397bc da4cd7d8 d4ac3bf0 d4ac3bd0
d790e7ce d7911cc1 00000523 d4ac3d00 d790e7d7 d7911ce4 da4cd7d8 00000341
da4ce664 da4cd8c0 da33fa6e 49524556 28335946 3d3d2030 65647620 626f5f76
Call Trace:
[<>] dump_stack+0x58/0x7c
[<>] spl_dumpstack+0x23/0x27 [spl]
[<>] spl_panic.cold.0+0x5/0x41 [spl]
[<>] ? dbuf_rele+0x3e/0x90 [zfs]
[<>] ? zap_lookup_norm+0xbe/0xe0 [zfs]
[<>] ? zap_lookup+0x57/0x70 [zfs]
[<>] ? vdev_obsolete_sm_object+0x102/0x12b [zfs]
[<>] vdev_indirect_sync_obsolete+0x3e1/0x64d [zfs]
[<>] ? txg_verify+0x1d/0x160 [zfs]
[<>] ? dmu_tx_create_dd+0x80/0xc0 [zfs]
[<>] vdev_sync+0xbf/0x550 [zfs]
[<>] ? mutex_lock+0x10/0x30
[<>] ? txg_list_remove+0x9f/0x1a0 [zfs]
[<>] ? zap_contains+0x4d/0x70 [zfs]
[<>] spa_sync+0x9f1/0x1b10 [zfs]
...
[<>] ? kthread_stop+0x110/0x110
This commit simply corrects the "integer_size" parameter used to lookup
the vdev's ZAP object.
Reviewed-by: Giuseppe Di Natale <guss80@gmail.com>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#8790
CID 186143: Memory - illegal accesses (USE_AFTER_FREE)
This patch fixes an use-after-free in spa_import_progress_destroy()
moving the kmem_free() call at the end of the function.
Reviewed-by: Chris Dunlop <chris@onthe.net.au>
Reviewed-by: Giuseppe Di Natale <guss80@gmail.com>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#8788
In `config/kernel-timer.m4` refactor slightly to check more generally
for the new `timer_setup()` APIs, but also check the callback signature
because some kernels (notably 4.14) have the new `timer_setup()` API but
use the old callback signature. Also add a check for a `flags` member in
`struct timer_list`, which was added in 4.1-rc8.
Add compatibility shims to `include/spl/sys/timer.h` to allow using the
new timer APIs with the only two caveats being that the callback
argument type must be declared as `spl_timer_list_t` and an explicit
assignment is required to get the timer variable for the `timer_of()`
macro. So the callback would look like this:
```c
__cv_wakeup(spl_timer_list_t t)
{
struct timer_list *tmr = (struct timer_list *)t;
struct thing *parent = from_timer(parent, tmr,
parent_timer_field);
... /* do stuff with parent */
```
Make some minor changes to `spl-condvar.c` and `spl-taskq.c` to use the
new timer APIs instead of conditional code.
Reviewed-by: Tomohiro Kusumi <kusumi.tomohiro@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rafael Kitover <rkitover@gmail.com>
Closes#8647
When reading kstats, the health (aka state) of the pool is stored into
/proc/spl/kstat/zfs/POOLNAME/state via spa_state_to_name().
However, during import/export there is a case where the spa exists,
but the root vdev does not exist. This fix checks that case and sets
the state to "TRANSITIONING"
Unfortunately, it is not easy to reproduce a test for this. It was
detected randomly during ZTS runs while kstats were also being sampled
regularly. After this change, further testing did not trip on the case
and the TRANSITIONING state was collected at least once by the kstats.
For posterity, the backtrace prior to this fix is:
[Mon May 13 17:21:00 2019] RIP: 0010:spa_state_to_name+0x10/0xb0 [zfs]
...
Mon May 13 17:21:00 2019] Call Trace:
[Mon May 13 17:21:00 2019] spa_state_data+0x1a/0x40 [zfs]
[Mon May 13 17:21:00 2019] kstat_seq_show+0x117/0x440 [spl]
[Mon May 13 17:21:00 2019] seq_read+0xe5/0x430
[Mon May 13 17:21:00 2019] proc_reg_read+0x45/0x70
[Mon May 13 17:21:00 2019] __vfs_read+0x1b/0x40
[Mon May 13 17:21:00 2019] vfs_read+0x8e/0x130
[Mon May 13 17:21:00 2019] SyS_read+0x55/0xc0
[Mon May 13 17:21:00 2019] ? SyS_fcntl+0x5d/0xb0
[Mon May 13 17:21:00 2019] do_syscall_64+0x73/0x130
[Mon May 13 17:21:00 2019] entry_SYSCALL_64_after_hwframe+0x3d/0xa2
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Richard Elling <Richard.Elling@RichardElling.com>
Closes#8746
Commit torvalds/linux@46ad0840b has removed the architecture specific
rwsem source and headers leaving only the generic version. As part
of this change the RWSEM_ACTIVE_READ_BIAS and RWSEM_ACTIVE_WRITE_BIAS
macros were moved to the private kernel/locking/rwsem.h header.
This results in a build failure because these macros were required
to implement the rw_tryupgrade() compatibility function.
In practice, this isn't a major problem because there are only a
few consumers of rw_tryupgrade() and because consumers of rw_tryupgrade
should be written to retry using rw_enter(RW_WRITER).
After auditing all of the callers only dmu_zfetch() was determined
not to perform a retry. It has been updated in this commit to
resolve this issue.
That said, the rw_tryupgrade() functionality should be considered
for possible removal in a future release due to the difficultly
in supporting the interface.
Reviewed-by: Tomohiro Kusumi <kusumi.tomohiro@gmail.com>
Reviewed-by: Chunwei Chen <tuxoko@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8730
The db_dirtycnt of an EVICTING dbuf is always 0. However, it still
appears in the dn_dbufs tree. If we call dnode_dirty_l1range on a
range that contains an EVICTING dbuf, we will attempt to mark it dirty
(which will fail because it's EVICTING, resulting in a new dbuf being
created and dirtied). Later, in ZFS_DEBUG mode, we assert that all the
dbufs in the range are dirty. If the EVICTING dbuf is still present,
this will trip the assertion erroneously.
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: Sara Hartse <sara.hartse@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#8745
When an import requires a long MMP activity check, or when the user
requests pool recovery, the import make take a long time. The user may
not know why, or be able to tell whether the import is progressing or is
hung.
Add a kstat which lists all imports currently being processed by the
kernel (currently only one at a time is possible, but the kstat allows
for more than one). The kstat is /proc/spl/kstat/zfs/import_progress.
The kstat contents are as follows:
pool_guid load_state multihost_secs max_txg pool_name
16667015954387398 3 15 0 tank3
load_state: the value of spa_load_state
multihost_secs: seconds until the end of the multihost activity
check; if over, or none required, this is 0
max_txg: current spa_load_max_txg, if rewind is occurring
This could be used by outside tools, such as a pacemaker resource agent,
to report import progress, or as a part of manual troubleshooting. The
zpool import subcommand could also be modified to report this
information.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#8696
These messages will want '\n' like any other regular printk() messages.
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@osnexus.com>
Closes#8726
Given how zfs_getattr() is implemented, zfs_getattr_fast() (used by
->getattr() of zpl inodes) also needs to consider an additional link
count if "snapdir" property is set to "visible".
Without this, # of directories in root inode of each dataset doesn't
match the link count when snapdir is visible.
Reviewed-by: Richard Yao <ryao@gentoo.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@osnexus.com>
Closes#8727
The 5.0 kernel defines the macro ASM_BUG. In order to prevent a
conflict and build failure rename ASM_BUG to ZFS_ASM_BUG. This
is currently only an issue on aarch64 but all instances of
ASM_BUG we're renamed to avoid any future conflict on x86_64.
Reviewed-by: Tomohiro Kusumi <kusumi.tomohiro@gmail.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Chris Dunlop <chris@onthe.net.au>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8725
Issue #8545
Commit 98bb45e resolved a deadlock which could occur when
handling a page fault in zfs_write(). This change added
the uio_fault_disable field to the uio structure but failed
to initialize it to B_FALSE. This uninitialized field would
cause uiomove_iov() to call __copy_from_user_inatomic()
instead of copy_from_user() resulting in unexpected EFAULTs.
Resolve the issue by fully initializing the uio, and clearing
the uio_fault_disable flags after it's used in zfs_write().
Additionally, reorder the uio_t field assignments to match
the order the fields are declared in the structure.
Reviewed-by: Chunwei Chen <tuxoko@gmail.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8640Closes#8719
Exported and documented a new module parameter.
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: DHE <git@dehacked.net>
Closes#8706
When receiving a DRR_OBJECT record the receive_object() function
needs to determine how to handle a spill block associated with the
object. It may need to be removed or kept depending on how the
object was modified at the source.
This determination is currently accomplished using a heuristic which
takes in to account the DRR_OBJECT record and the existing object
properties. This is a problem because there isn't quite enough
information available to do the right thing under all circumstances.
For example, when only the block size changes the spill block is
removed when it should be kept.
What's needed to resolve this is an additional flag in the DRR_OBJECT
which indicates if the object being received references a spill block.
The DRR_OBJECT_SPILL flag was added for this purpose. When set then
the object references a spill block and it must be kept. Either
it is update to date, or it will be replaced by a subsequent DRR_SPILL
record. Conversely, if the object being received doesn't reference
a spill block then any existing spill block should always be removed.
Since previous versions of ZFS do not understand this new flag
additional DRR_SPILL records will be inserted in to the stream.
This has the advantage of being fully backward compatible. Existing
ZFS systems receiving this stream will recreate the spill block if
it was incorrectly removed. Updated ZFS versions will correctly
ignore the additional spill blocks which can be identified by
checking for the DRR_SPILL_UNMODIFIED flag.
The small downside to this approach is that is may increase the size
of the stream and of the received snapshot on previous versions of
ZFS. Additionally, when receiving streams generated by previous
unpatched versions of ZFS spill blocks may still be lost.
OpenZFS-issue: https://www.illumos.org/issues/9952
FreeBSD-issue: https://bugs.freebsd.org/bugzilla/show_bug.cgi?id=233277
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8668
`zfs set atime|relatime=off|on` doesn't disable or enable the property
on read for datasets whose property was inherited from parent, until
a dataset is once unmounted and mounted again.
(The properties start to work properly if a dataset is once unmounted
and mounted again. The difference comes from regular mount process,
e.g. via zpool import, uses mount options based on properties read
from ondisk layout for each dataset, whereas
`zfs set atime|relatime=off|on` just remounts a specified dataset.)
--
# zpool create p1 <device>
# zfs create p1/f1
# zfs set atime=off p1
# echo test > /p1/f1/test
# sync
# zfs list
NAME USED AVAIL REFER MOUNTPOINT
p1 176K 18.9G 25.5K /p1
p1/f1 26K 18.9G 26K /p1/f1
# zfs get atime
NAME PROPERTY VALUE SOURCE
p1 atime off local
p1/f1 atime off inherited from p1
# stat /p1/f1/test | grep Access | tail -1
Access: 2019-04-26 23:32:33.741205192 +0900
# cat /p1/f1/test
test
# stat /p1/f1/test | grep Access | tail -1
Access: 2019-04-26 23:32:50.173231861 +0900
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ changed by read(2)
--
The problem is that zfsvfs::z_atime which was probably intended to keep
incore atime state just gets updated by a callback function of "atime"
property change, atime_changed_cb(), and never used for anything else.
Since now that all file read and atime update use a common function
zpl_iter_read_common() -> file_accessed(), and whether to update atime
via ->dirty_inode() is determined by atime_needs_update(),
atime_needs_update() needs to return false once atime is turned off.
It currently continues to return true on `zfs set atime=off`.
Fix atime_changed_cb() by setting or dropping SB_NOATIME in VFS super
block depending on a new atime value, so that atime_needs_update() works
as expected after property change.
The same problem applies to "relatime" except that a self contained
relatime test is needed. This is because relatime_need_update() is based
on a mount option flag MNT_RELATIME, which doesn't exist in datasets
with inherited "relatime" property via `zfs set relatime=...`, hence it
needs its own relatime test zfs_relatime_need_update().
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@gmail.com>
Closes#8674Closes#8675
Drop duplicated phrases in comments.
Also drop an obsolete comment "Perform a mount of the associated...",
as all it does now is get objid from DMU and lookup incore inode.
Reviewed-by: Giuseppe Di Natale <guss80@gmail.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@gmail.com>
Closes#8707
Linux kernel commit ca79b0c211af63fa3276f0e3fd7dd9ada2439839
"mm: convert totalram_pages and totalhigh_pages variables to atomic"
replaced `totalhigh_pages` with an inline function `totalhigh_pages()`.
This broke compilation on IA32, etc, as ZoL uses `totalhigh_pages`
on archs with highmem. Confirmed on Fedora 30 (5.0.9-301.fc30.i686).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@gmail.com>
Closes#8677Closes#8701
The kernel function which adds new zvols as disks to the system,
add_disk(), briefly opens and closes the zvol as part of its work.
Closing a zvol involves waiting for two txgs to sync. This, combined
with the fact that the taskq processing new zvols is single threaded,
makes this processing new zvols slow.
Waiting for these txgs to sync is only necessary if the zvol has been
written to, which is not the case during add_disk(). This change adds
tracking of whether a zvol has been written to so that we can skip the
txg_wait_synced() calls when they are unnecessary.
This change also fixes the flags passed to blkdev_get_by_path() by
vdev_disk_open() to be FMODE_READ | FMODE_WRITE | FMODE_EXCL instead of
just FMODE_EXCL. The flags were being incorrectly calculated because
we were using the wrong version of vdev_bdev_mode().
Reviewed-by: George Wilson <george.wilson@delphix.com>
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: John Gallagher <john.gallagher@delphix.com>
Closes#8526Closes#8615
The comment in lz4_compress_zfs could be more clear and specific. It
also contains needlessly strong language.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes: #8702Closes: #8703
The 'zpool resilver' command requires that the resilver_defer
feature is active on the pool. Unfortunately, the check for
this was left out of the original patch. This commit simply
corrects this so that the command properly returns an error
in this case.
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#8700
The size argument of snprintf(3) in glibc and snprintf() in Linux
kernel includes trailing \0, as snprintf(3) man page explains it as
"write at most size bytes (including the trailing null byte ('\0'))",
i.e. snprintf() can just take buffer size.
e.g. For snprintf() in module/zfs/zfs_ctldir.c, a buffer size is
MAXPATHLEN, and a caller is passing MAXPATHLEN to snprintf(), so size
should just be `path_len` to do what the caller is trying to do.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@gmail.com>
Closes#8692
Not all block devices, notably scsi_debug, set a root_blkg on the
request queue. Remove this assertion and allow the the existing
call to blkg_tryget() to gracefully handle the NULL (which it does).
Reviewed-by: Tomohiro Kusumi <kusumi.tomohiro@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8678
Use NV_ENCODE_NATIVE for nvlist encoding variable instead of 0.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Chris Dunlop <chris@onthe.net.au>
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@gmail.com>
Closes#8653
Use either SEEK_* or 0,1,2..., but not both.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@gmail.com>
Closes#8656
This patch fixes 2 issues with the DMU free throttle implemented
in dmu_free_long_range(). The first issue is that get_next_chunk()
was calculating the number of L1 blocks the free would dirty
incorrectly. In some cases involving extremely large files, this
code would greatly overestimate the number of effected L1 blocks,
causing excessive calls to txg_wait_open(). This patch corrects
the calculation.
The second issue is that the free throttle uses the total number
of free'd blocks in all (open, quiescing, and syncing) txgs to
determine whether to throttle. This causes large frees (such as
those created by the first issue) to cause 4 txg syncs before
any further frees were allowed to proceed. This patch ensures
that the accounting is done entirely in a per-txg fashion, so
that frees from a given txg don't affect those that immediately
follow it.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#8655
Unused since 5649246dd3("Remove znode move functionality"),
and ZNODE_STAT_ADD() will never be needed.
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@gmail.com>
Closes#8636
These aren't unused.
`flag` in zfs_create() also isn't to indicate large file.
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@gmail.com>
Closes#8635
1. Support QAT when ZFS is root file-system:
When ZFS module is loaded before QAT started, the QAT can
be started again in post-process, e.g.:
echo 0 > /sys/module/zfs/parameters/zfs_qat_compress_disable
echo 0 > /sys/module/zfs/parameters/zfs_qat_encrypt_disable
echo 0 > /sys/module/zfs/parameters/zfs_qat_checksum_disable
2. Verify alder checksum of the de-compress result
3. Allocate Digest, IV and AAD buffer in physical contiguous
memory by QAT_PHYS_CONTIG_ALLOC.
4. Update the documentation for zfs_qat_compress_disable,
zfs_qat_checksum_disable, zfs_qat_encrypt_disable.
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Weigang Li <weigang.li@intel.com>
Signed-off-by: Chengfeix Zhu <chengfeix.zhu@intel.com>
Closes#8323Closes#8610
This replaces empty for loops with while loops to make the code easier
to read.
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reported-by: github.com/dcb314
Signed-off-by: Richard Laager <rlaager@wiktel.com>
Closes#6681Closes#6682Closes#6683Closes#8623
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Laager <rlaager@wiktel.com>
Closes#8626
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Laager <rlaager@wiktel.com>
Closes#8626
When receiving a raw send stream only reallocated objects
whose contents were not freed by the standard indicators
should call dmu_free_long_range().
Furthermore, if calling dmu_free_long_range() is required
then the objects current block size must be used and not
the new block size.
Two additional test cases were added to provided realistic
test coverage for processing reallocated objects which are
part of a raw receive.
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#8528Closes#8607
This patch simply up cleans up a nit and corrects an error message
issue that were introduced in the Multiple DVA scrub patch.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#8619
When receiving an object to a previously allocated interior slot
the new object should be "allocated" by setting DMU_NEW_OBJECT,
not "reallocated" with dnode_reallocate(). For resilience verify
the slot is free as required in case the stream is malformed.
Add a test case to generate more realistic incremental send streams
that force reallocation to occur during the receive.
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8067Closes#8614
Fix style issue for 'tx->tx_txg&TXG_MASK'. There should be white
space around the '&' character. Split the dnode_reallocate() ASSERT
to make it more readable to clearly separate the checks.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8606
The error path in zio_crypt_key_unwrap would call zio_crypt_key_destroy which
calls rw_destroy(&key->zk_salt_lock); which has not yet been initialized.
We move the rw_init() call to the start of zio_crypt_key_unwrap instead.
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Closes#8604Closes#8605
The bulk[] array index, count, must be reset per-iteration in order to
not overwrite the stack.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Chris Dunlop <chris@onthe.net.au>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: Tim Chase <tim@chase2k.com>
Closes#8072Closes#8597Closes#8601
d12614521a("Fixes for procfs files backed by linked lists")
uses PDE_DATA(), but since PDE_DATA() (public interface which
replaced old public interface PDE()) first appeared in upstream
kernel 3.10, it lacks visible local definition for kernel < 3.10.
Move the local PDE_DATA() definition to a ZoL header, to unbreak
build on kernel < 3.10.
--
module/spl/spl-procfs-list.c: In function 'procfs_list_open':
module/spl/spl-procfs-list.c:166: error: implicit declaration of function 'PDE_DATA'
module/spl/spl-procfs-list.c:166: warning: assignment makes pointer from integer without a cast
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Gallagher <john.gallagher@delphix.com>
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@gmail.com>
Closes#8599
This partially reverts commit 5dbf8b4ed. This change resolved
the issues observed with truncated files in raw sends. However,
the required changes to dnode_allocate() introduced a regression
for non-raw streams which needs to be understood.
The additional debugging improvements from the original patch
were not reverted.
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #7378
Issue #8528
Issue #8540
Issue #8565Close#8584
When a pool is initially created (by `zpool create`), predictive
prefetch is inadvertently disabled, until the pool is export/import-ed,
or the machine is rebooted.
When device removal was introduced, we added some code to disable
predictive prefetching until indirect vdevs have been loaded. This
resulted in the "default state" of prefetch being disabled, until we
proactively enable it after indirect vdevs are loaded. Unfortunately
this resulted in a few bugs where in some code paths we neglect to
enable predictive prefetch. The first of these was fixed by
20507534d4
This commit fixes another case where we also need to explicitly enable
predictive prefetch, when the pool is initially created.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#8577
The features.kernel layout should match features.pool.
Reviewed-by: Sara Hartse <sara.hartse@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@delphix.com>
Closes#8566
There are several places where we use zfs_dbgmsg and %p to
print pointers. In the Linux kernel, these values obfuscated
to prevent information leaks which means the pointers aren't
very useful for debugging crash dumps. We decided to restrict
the permissions of dbgmsg (and some other kstats while we were
at it) and print pointers with %px in zfs_dbgmsg as well as
spl_dumpstack
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Gallagher <john.gallagher@delphix.com>
Signed-off-by: sara hartse <sara.hartse@delphix.com>
Closes#8467Closes#8476
Callers of txg_wait_open() which set should_quiesce=B_TRUE should be
accounted for as iowait time. Otherwise, the caller is understood
to be idle and cv_wait_sig() is used to prevent incorrectly inflating
the system load average.
Similarly txg_wait_wait() has been updated to use cv_wait_io() to
be accounted against iowait.
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8550Closes#8558
UNMAP/TRIM support is a frequently-requested feature to help
prevent performance from degrading on SSDs and on various other
SAN-like storage back-ends. By issuing UNMAP/TRIM commands for
sectors which are no longer allocated the underlying device can
often more efficiently manage itself.
This TRIM implementation is modeled on the `zpool initialize`
feature which writes a pattern to all unallocated space in the
pool. The new `zpool trim` command uses the same vdev_xlate()
code to calculate what sectors are unallocated, the same per-
vdev TRIM thread model and locking, and the same basic CLI for
a consistent user experience. The core difference is that
instead of writing a pattern it will issue UNMAP/TRIM commands
for those extents.
The zio pipeline was updated to accommodate this by adding a new
ZIO_TYPE_TRIM type and associated spa taskq. This new type makes
is straight forward to add the platform specific TRIM/UNMAP calls
to vdev_disk.c and vdev_file.c. These new ZIO_TYPE_TRIM zios are
handled largely the same way as ZIO_TYPE_READs or ZIO_TYPE_WRITEs.
This makes it possible to largely avoid changing the pipieline,
one exception is that TRIM zio's may exceed the 16M block size
limit since they contain no data.
In addition to the manual `zpool trim` command, a background
automatic TRIM was added and is controlled by the 'autotrim'
property. It relies on the exact same infrastructure as the
manual TRIM. However, instead of relying on the extents in a
metaslab's ms_allocatable range tree, a ms_trim tree is kept
per metaslab. When 'autotrim=on', ranges added back to the
ms_allocatable tree are also added to the ms_free tree. The
ms_free tree is then periodically consumed by an autotrim
thread which systematically walks a top level vdev's metaslabs.
Since the automatic TRIM will skip ranges it considers too small
there is value in occasionally running a full `zpool trim`. This
may occur when the freed blocks are small and not enough time
was allowed to aggregate them. An automatic TRIM and a manual
`zpool trim` may be run concurrently, in which case the automatic
TRIM will yield to the manual TRIM.
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: George Wilson <george.wilson@delphix.com>
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Contributions-by: Saso Kiselkov <saso.kiselkov@nexenta.com>
Contributions-by: Tim Chase <tim@chase2k.com>
Contributions-by: Chunwei Chen <tuxoko@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8419Closes#598
This patch fixes a few issues with raw receives involving
truncated files:
* dnode_reallocate() now calls dnode_set_blksz() instead of
dnode_setdblksz(). This ensures that any remaining dbufs with
blkid 0 are resized along with their containing dnode upon
reallocation.
* One of the calls to dmu_free_long_range() in receive_object()
needs to check that the object it is about to free some contents
or hasn't been completely removed already by a previous call to
dmu_free_long_object() in the same function.
* The same call to dmu_free_long_range() in the previous point
needs to ensure it uses the object's current block size and
not the new block size. This ensures the blocks of the object
that are supposed to be freed are completely removed and not
simply partially zeroed out.
This patch also adds handling for DRR_OBJECT_RANGE records to
dprintf_drr() for debugging purposes.
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#7378Closes#8528
Make a local copy of the vd_path and preserve the removal error
for use in spa_history_log_internal(). This is required because
after spa_vdev_exit() there is nothing preventing the vdev state
from changing.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: Igor Kozhukhov <igor@dilos.org>
Closes#8522
Added missing remove of detachable VDEV from txg's DTL list
to avoid use-after-free for the split VDEV
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Signed-off-by: Roman Strashkin <roman.strashkin@nexenta.com>
Closes#5565Closes#7856
ZFS supports O_RSYNC for read operations and when specified will ensure
the same level of data integrity that O_DSYNC and O_SYNC provides for
writes. O_RSYNC by itself has no effect so it must be combined with
either O_DSYNC or O_SYNC. However, many platforms don't support O_RSYNC
and have mapped O_SYNC to mean O_RSYNC within ZFS. This is incorrect
and causes unnecessary calls to zil_commit. Only platforms which
support O_RSYNC should implement the zil_commit functionality in the
read code path.
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Wilson <george.wilson@delphix.com>
Closes#8523
When Multihost is enabled, and a pool is imported, uberblock writes
include ub_mmp_delay to allow an importing node to calculate the
duration of an activity test. This value, is not enough information.
If zfs_multihost_fail_intervals > 0 on the node with the pool imported,
the safe minimum duration of the activity test is well defined, but does
not depend on ub_mmp_delay:
zfs_multihost_fail_intervals * zfs_multihost_interval
and if zfs_multihost_fail_intervals == 0 on that node, there is no such
well defined safe duration, but the importing host cannot tell whether
mmp_delay is high due to I/O delays, or due to a very large
zfs_multihost_interval setting on the host which last imported the pool.
As a result, it may use a far longer period for the activity test than
is necessary.
This patch renames ub_mmp_sequence to ub_mmp_config and uses it to
record the zfs_multihost_interval and zfs_multihost_fail_intervals
values, as well as the mmp sequence. This allows a shorter activity
test duration to be calculated by the importing host in most situations.
These values are also added to the multihost_history kstat records.
It calculates the activity test duration differently depending on
whether the new fields are present or not; for importing pools with
only ub_mmp_delay, it uses
(zfs_multihost_interval + ub_mmp_delay) * zfs_multihost_import_intervals
Which results in an activity test duration less sensitive to the leaf
count.
In addition, it makes a few other improvements:
* It updates the "sequence" part of ub_mmp_config when MMP writes
in between syncs occur. This allows an importing host to detect MMP
on the remote host sooner, when the pool is idle, as it is not limited
to the granularity of ub_timestamp (1 second).
* It issues writes immediately when zfs_multihost_interval is changed
so remote hosts see the updated value as soon as possible.
* It fixes a bug where setting zfs_multihost_fail_intervals = 1 results
in immediate pool suspension.
* Update tests to verify activity check duration is based on recorded
tunable values, not tunable values on importing host.
* Update tests to verify the expected number of uberblocks have valid
MMP fields - fail_intervals, mmp_interval, mmp_seq (sequence number),
that sequence number is incrementing, and that uberblock values match
tunable settings.
Reviewed-by: Andreas Dilger <andreas.dilger@whamcloud.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#7842
In addition to dsl_dataset_evict_async() releasing a hold, there is
an error case in dsl_dataset_hold_obj() which had missed 4 additional
release calls. This was introduced in a1d477c24.
openzfsonosx-commit: https://github.com/openzfsonosx/zfs/commit/63ff7f1c
Authored by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8517
If the buffer 'digest_buffer' is allocated in the qat_checksum()
stack, it can't ensure that the address is physically contiguous,
and the DMA result of the buffer may be handled incorrectly.
Using QAT_PHYS_CONTIG_ALLOC() ensures a physically
contiguous allocation.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: Chengfei, Zhu <chengfeix.zhu@intel.com>
Closes#8323Closes#8521
Update the dirty check in dmu_offset_next() such that dnode's
are only considered dirty for the purpose or reporting holes
when there are pending data blocks or frees to be synced. This
ensures that when there are only metadata updates to be synced
(atime) that holes are reported.
Reviewed-by: Debabrata Banerjee <dbanerje@akamai.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6958Closes#8505
As it turns out, on the Windows platform when rw_init() is called
(rather its bedrock call ExInitializeResourceLite) it is placed on
an active-list of locks, and is removed at rw_destroy() time.
dnode_move() has logic to copy over the old-dnode to new-dnode,
including calling dmu_zfetch_init(new-dnode). But due to the missing
dmu_zfetch_fini(old-dnode), kmem will call dnode_dest() to release the
memory (and in debug builds fill pattern 0xdeadbeef) over the Windows
active-lock's prev/next list pointers, making Windows sad.
But on other platforms, the contents of dmu_zfetch_fini() is one
call to list_destroy() and one to rw_destroy(), which is effectively
a no-op call and is not required. This commit is mostly for
"correctness" and can be skipped there.
Porting Notes:
* This leak exists on Linux but currently can never happen because
the dnode_move() functionality is not supported.
openzfsonosx-commit: openzfsonosx/zfs@d95fe517
Authored by: Julian Heuking <JulianH@beckhoff.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Closes#8519
When destroying an arc_buf_hdr_t its identity cannot be discarded
until it is entirely undiscoverable. This not only includes being
unhashed, but also being removed from the l2arc header list.
Discarding the header's identify prematurely renders the hash
lock useless because it will always hash to bucket zero.
This change resolves a race with l2arc_evict() by discarding the
identity after it has been removed from the l2arc header list.
This ensures either the header is not on the list or contains
the correct identify.
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7688Closes#8144
Currently, there is an issue in the sequential scrub code which
prevents self healing from working in some cases. The scrub code
will split up all DVA copies of a bp and issue each of them
separately. The problem is that, since each of the DVAs is no
longer associated with the others, the self healing code doesn't
have the opportunity to repair problems that show up in one of the
DVAs with the data from the others.
This patch fixes this issue by ensuring that all IOs issued by the
sequential scrub code include all DVAs. Initially, only the first
DVA of each is attempted. If an issue arises, the IO is retried
with all available copies, giving the self healing code a chance
to correct the issue.
To test this change, this patch also adds the ability for zinject
to specify individual DVAs to inject read errors into. We then
add a new test case that utilizes this functionality to ensure
scrubs and self-healing reads can handle and transparently fix
issues with individual copies of blocks.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#8453
The number of IO and checksum events should match the number of errors
seen in zpool status. Previously there was a mismatch between the
two counts because zpool status would only count unrecovered errors,
while zpool events would get an event for *all* errors (recovered or
not). This lead to situations where disks could be faulted for
"too many errors", while at the same time showing zero errors in zpool
status.
This fixes the zpool status error counters to increment at the same
times we post the error events.
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#4851Closes#7817
This patch simply fixes some small memory leaks that can happen
during error handling in zfsvfs_create_impl(). If the function
fails, it frees all the memory / references it created.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#8490
This patch attempts to address some user concerns that have arisen
since errata 4 was introduced.
* The errata warning has been made less scary for users without
any encrypted datasets.
* The errata warning now clears itself without a pool reimport if
the bookmark_v2 feature is enabled and no encrypted datasets
exist.
* It is no longer possible to create new encrypted datasets without
enabling the bookmark_v2 feature, thus helping to ensure that the
errata is resolved.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Issue ##8308
Closes#8504
Before sequential scrub patches ZFS never aggregated I/Os above 128KB.
Sequential scrub bumped that to 1MB, supposedly to reduce number of
head seeks for spinning disks. But for SSDs it makes little to no
sense, especially on FreeBSD, where due to MAXPHYS limitation device
will likely still see bunch of 128KB I/Os instead of one large.
Having more strict aggregation limit for SSDs allows to avoid
allocation of large memory buffer and copy to/from it, that is a
serious problem when throughput reaches gigabytes per second.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#8494
Currently, there is an issue in the raw receive code where
raw receives are allowed to happen on top of previously
non-raw received datasets. This is a problem because the
source-side dataset doesn't know about how the blocks on
the destination were encrypted. As a result, any MAC in
the objset's checksum-of-MACs tree that is a parent of both
blocks encrypted on the source and blocks encrypted by the
destination will be incorrect. This will result in
authentication errors when we decrypt the dataset.
This patch fixes this issue by adding a new check to the
raw receive code. The code now maintains an "IVset guid",
which acts as an identifier for the set of IVs used to
encrypt a given snapshot. When a snapshot is raw received,
the destination snapshot will take this value from the
DRR_BEGIN payload. Non-raw receives and normal "zfs snap"
operations will cause ZFS to generate a new IVset guid.
When a raw incremental stream is received, ZFS will check
that the "from" IVset guid in the stream matches that of
the "from" destination snapshot. If they do not match, the
code will error out the receive, preventing the problem.
This patch requires an on-disk format change to add the
IVset guids to snapshots and bookmarks. As a result, this
patch has errata handling and a tunable to help affected
users resolve the issue with as little interruption as
possible.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#8308
This patch adds the bookmark v2 feature to the on-disk format. This
feature will be needed for the upcoming redacted sends and for an
upcoming fix that for raw receives. The feature is not currently
used by any code and thus this change is a no-op, aside from the
fact that the user can now enable the feature.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Issue #8308
Currently, the receive code can create an unreadable dataset from
a correct raw send stream. This is because it is currently
impossible to set maxblkid to a lower value without freeing the
associated object. This means truncating files on the send side
to a non-0 size could result in corruption. This patch solves this
issue by adding a new 'force' flag to dnode_new_blkid() which will
allow the raw receive code to force the DMU to accept the provided
maxblkid even if it is a lower value than the existing one.
For testing purposes the send_encrypted_files.ksh test has been
extended to include a variety of truncated files and multiple
snapshots. It also now leverages the xattrtest command to help
ensure raw receives correctly handle xattrs.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#8168Closes#8487
Most of the zfs_arc_* module parameters do not have their values used by
the ARC code directly. Instead, there is a function, arc_tuning_update,
which is called during module initialization and periodically
thereafter, whose job is to fetch the module parameter values, clamp/
limit them appropriately, and then assign those values to a separate set
of internal variables that are actually referenced by the ARC code.
Commit 3ec34e55 featured an overhaul of arc_reclaim_thread, which is the
former location where the post-init-time calls to arc_tuning_update
would occur. The rework split the work previously done by the
arc_reclaim_thread into a pair of replacement threads; and
unfortunately, the call to arc_tuning_update fell through the cracks and
was lost in the reorganization.
This meant that changing almost any ARC-related zfs module parameter via
/sys/module/zfs/parameters/ would result in the module parameter value
itself appearing to change; however the modification would not actually
propagate to the ARC code and have any real effect.
This commit reinstates the post-init-time call to arc_tuning_update. It
is now called during arc_adjust_cb_check; this should be equivalent to
its former call location in arc_reclaim_thread.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Justin Gottula <justin@jgottula.com>
Closes#8405Closes#8463
This patch modifies the zfs_ioc_snapshot_list_next() ioctl to enable it
to take input parameters that alter the way looping through the list of
snapshots is performed. The idea here is to restrict functions that
throw away some of the snapshots returned by the ioctl to a range of
snapshots that these functions actually use. This improves efficiency
and execution speed for some rollback and send operations.
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Signed-off-by: Alek Pinchuk <apinchuk@datto.com>
Closes#8077
Resolve a vdev_initialize crash uncovered by ztest. Similar
to when starting a new initialization verify that a removal
is not in progress. Additionally, do not restart when the
thread already exists. This check is now congruent with the
POOL_INITIALIZE_DO handling in spa_vdev_initialize_impl().
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8477
Instead of choosing a leaf vdev quasi-randomly, by starting at the root
vdev and randomly choosing children, rotate over leaves to issue MMP
writes. This fixes an issue in a pool whose top-level vdevs have
different numbers of leaves.
The issue is that the frequency at which individual leaves are chosen
for MMP writes is based not on the total number of leaves but based on
how many siblings the leaves have.
For example, in a pool like this:
root-vdev
+------+---------------+
vdev1 vdev2
| |
| +------+-----+-----+----+
disk1 disk2 disk3 disk4 disk5 disk6
vdev1 and vdev2 will each be chosen 50% of the time. Every time vdev1
is chosen, disk1 will be chosen. However, every time vdev2 is chosen,
disk2 is chosen 20% of the time. As a result, disk1 will be sent 5x as
many MMP writes as disk2.
This may create wear issues in the case of SSDs. It also reduces the
effectiveness of MMP as it depends on the writes being evenly
distributed for the case where some devices fail or are partitioned.
The new code maintains a list of leaf vdevs in the pool. MMP records
the last leaf used for an MMP write in mmp->mmp_last_leaf. To choose
the next leaf, MMP starts at mmp->mmp_last_leaf and traverses the list,
continuing from the head if the tail is reached. It stops when a
suitable leaf is found or all leaves have been examined.
Added a test to verify MMP write distribution is even.
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Kash Pande <kash@tripleback.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#7953
The linux kernel's nfsd implementation use RWF_SYNC to determine if the
write is synchronous or not. This flag is used to set the kernel's I/O
control block flags. Unfortunately, ZFS was not updated to inspect these
flags so NFS sync writes were not being honored.
This change maps the IOCB_* flags to the ZFS equivalent.
Reviewed-by: Don Brady <don.brady@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Wilson <george.wilson@delphix.com>
Closes#8474Closes#8452Closes#8486
Commit torvalds/linux@736706bee has removed the get_fs() function
as a bit of cleanup. It has been defined as KERNEL_DS on all
architectures for all supported kernels. Replace get_fs() with
KERNEL_DS as was done in the kernel.
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8479
The function bpobj_iterate_impl overflows the stack when bpobjs
are deeply nested. Rewrite the function to eliminate the recursion.
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Zuchowski <pzuchowski@datto.com>
Closes#7674Closes#7675Closes#7908
Before allowing new allocations to the metaslab we need to ensure
that any issued initializing writes have been synced. Otherwise,
it's possible for metaslab_block_alloc() to allocate a range which
is about to be overwritten by an initializing IO.
Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed-by: George Wilson <george.wilson@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8461
Fix indentation of code in ifdef's.
Remove obsolete comment.
Make if/else statements more readable by adding braces.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#8459
