As of linux-2.6.36 the BIO_RW_FAILFAST and REQ_FAILFAST flags
have been unified under the REQ_* names. These flags always had
to be kept in-sync so this is a nice step forward, unfortunately
it means we need to be careful to only use the new unified flags
when the BIO_RW_* flags are not defined. Additional autoconf
checks were added for this and if it is ever unclear which method
to use no flags are set. This is safe but may result in longer
delays before a disk is failed.
Perferred interface for setting FAILFAST on a bio:
2.6.12-2.6.27: BIO_RW_FAILFAST
2.6.28-2.6.35: BIO_RW_FAILFAST_{DEV|TRANSPORT|DRIVER}
2.6.36-2.6.xx: REQ_FAILFAST_{DEV|TRANSPORT|DRIVER}
It turns out that 'zpool events' over 1024 bytes in size where being
silently dropped. This was discovered while writing the zfault.sh
tests to validate common failure modes.
This could occur because the zfs interface for passing an arbitrary
size nvlist_t over an ioctl() is to provide a buffer for the packed
nvlist which is usually big enough. In this case 1024 byte is the
default. If the kernel determines the buffer is to small it returns
ENOMEM and the minimum required size of the nvlist_t. This was
working properly but in the case of 'zpool events' the event stream
was advanced dispite the error. Thus the retry with the bigger
buffer would succeed but it would skip over the previous event.
The fix is to pass this size to zfs_zevent_next() and determine
before removing the event from the list if it will fit. This was
preferable to checking after the event was returned because this
avoids the need to rewind the stream.
While there is no right maximum timeout for a disk IO we can start
laying the ground work to measure how long they do take in practice.
This change simply measures the IO time and if it exceeds 30s an
event is posted for 'zpool events'.
This value was carefully selected because for sd devices it implies
that at least one timeout (SD_TIMEOUT) has occured. Unfortunately,
even with FAILFAST set we may retry and request and not get an
error. This behavior is strongly dependant on the device driver
and how it is hooked in to the scsi error handling stack. However
by setting the limit at 30s we can log the event even if no error
was returned.
Slightly longer term we can start recording these delays perhaps
as a simple power-of-two histrogram. This histogram can then be
reported as part of the 'zpool status' command when given an command
line option.
None of this code changes the internal behavior of ZFS. Currently
it is simply for reporting excessively long delays.
ZFS works best when it is notified as soon as possible when a device
failure occurs. This allows it to immediately start any recovery
actions which may be needed. In theory Linux supports a flag which
can be set on bio's called FAILFAST which provides this quick
notification by disabling the retry logic in the lower scsi layers.
That's the theory at least. In practice is turns out that while the
flag exists you oddly have to set it with the BIO_RW_AHEAD flag.
And even when it's set it you may get retries in the low level
drivers decides that's the right behavior, or if you don't get the
right error codes reported to the scsi midlayer.
Unfortunately, without additional kernels patchs there's not much
which can be done to improve this. Basically, this just means that
it may take 2-3 minutes before a ZFS is notified properly that a
device has failed. This can be improved and I suspect I'll be
submitting patches upstream to handle this.
By default the Solaris code does not log speculative or soft io errors
in either 'zpool status' or post an event. Under Linux we don't want
to change the expected behavior of 'zpool status' so these io errors
are still suppressed there.
However, since we do need to know about these events for Linux FMA and
the 'zpool events' interface is new we do post the events. With the
addition of the zio_flags field the posted events now contain enough
information that a user space consumer can identify and discard these
events if it sees fit.
Previously the project contained who zfs_context.h files,
one for user space builds and one for kernel space builds.
It was the responsibility of the source including the file
to ensure the right one was included based on the order of
the include paths.
This was the way it was done in OpenSolaris but for our
purposes I felt it was overly obscure. The user and kernel
zfs_context.h files have been combined in to a single file
and a #define determines if you get the user or kernel
context.
The issue here was that I used the _KERNEL macro which is
defined as part of the spl which will only be defined for
most builds after you include the right zfs_context. It is
safer to use the __KERNEL__ macro which is automatically
defined as part of the kernel build process and passed as
a command line compiler option. It will always be defined
if your building in the kernel and never for user space.
One of the neat tricks an autoconf style project is capable of
is allow configurion/building in a directory other than the
source directory. The major advantage to this is that you can
build the project various different ways while making changes
in a single source tree.
For example, this project is designed to work on various different
Linux distributions each of which work slightly differently. This
means that changes need to verified on each of those supported
distributions perferably before the change is committed to the
public git repo.
Using nfs and custom build directories makes this much easier.
I now have a single source tree in nfs mounted on several different
systems each running a supported distribution. When I make a
change to the source base I suspect may break things I can
concurrently build from the same source on all the systems each
in their own subdirectory.
wget -c http://github.com/downloads/behlendorf/zfs/zfs-x.y.z.tar.gz
tar -xzf zfs-x.y.z.tar.gz
cd zfs-x-y-z
------------------------- run concurrently ----------------------
<ubuntu system> <fedora system> <debian system> <rhel6 system>
mkdir ubuntu mkdir fedora mkdir debian mkdir rhel6
cd ubuntu cd fedora cd debian cd rhel6
../configure ../configure ../configure ../configure
make make make make
make check make check make check make check
This change also moves many of the include headers from individual
incude/sys directories under the modules directory in to a single
top level include directory. This has the advantage of making
the build rules cleaner and logically it makes a bit more sense.
