When failmode=continue is set and the pool suspends, both 'zpool status'
and the 'zfs/pool/state' kstat ignore it and report the normal vdev tree
state. There's no clear indicator that the pool is suspended. This is
unlike suspend in failmode=wait, or suspend due to MMP check failure,
which both report "SUSPENDED" explicitly.
This commit changes it so SUSPENDED is reported for failmode=continue
the same as for other modes.
Rationale:
The historical behaviour of failmode=continue is roughly, "press on as
though all is well". To this end, the fact that the pool had suspended
was not shown, to maintain the façade that all is well.
Its unclear why hiding this information was considered appropriate. One
possibility is that it was expected that a true pool fault would always
be reported as DEGRADED or FAULTED, and that the pool could not suspend
without these happening.
That is not necessarily true, as vdev health and suspend state are only
loosely connected, such that a pool in (apparent) good health can be
suspended for good reasons, and of course a degraded pool does not lead
to suspension. Even if that expectation were true, there's still a
difference in urgency - a degraded pool may not need to be attended to
for hours, while a suspended pool is most often unusable until an
operator intervenes.
An operator that has set failmode=continue has presumably done so
because their workload is one that can continue to operate in a useful
way when the pool suspends. In this case the operator still needs a
clear indicator that there is a problem that needs attending to.
Sponsored-by: Klara, Inc.
Sponsored-by: Wasabi Technology, Inc.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Closes#15297
We have occasional crashes in the rsend tests. Debugging revealed
that this is because the send_worker thread is getting EINTR from
splice(). This happens when a non-fatal signal is received during
the syscall. We should retry the syscall, rather than exiting failure.
Tweak the loop to only break if the splice is finished or we receive
a non-EINTR error.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#15273
For zpool import and zpool split, zpool_enable_datasets is called
to mount and share all datasets in a pool. If there is an error
while mounting or sharing any dataset in the pool, the status of
import or split is reported as failure. However, the changes do
show up in zpool list.
This commit updates the error reporting in zpool import and zpool
split path. More descriptive messages are shown to user in case
there is an error during mount or share. Errors in mount or share
do not effect the overall status of zpool import and zpool split.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Umer Saleem <usaleem@ixsystems.com>
Closes#15216
POSIX timers target the process, not the thread (as does SIGINFO),
so we need to block it in the main thread which will die if interrupted.
Ref: https://101010.pl/@ed1conf@bsd.network/110731819189629373
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#15113
When the vdev properties features was merged an extra check
was added in `spa_vdev_remove_top_check()` which checked
whether the vdev that we want to remove is already being
removed and if so return an EALREADY error.
```
static int
spa_vdev_remove_top_check(vdev_t *vd)
{
... <snip> ...
/*
* This device is already being removed
*/
if (vd->vdev_removing)
return (SET_ERROR(EALREADY));
```
Before that change we'd still fail with an error but it
was a more generic one - here is the check that failed
later in the same function:
```
/*
* There can not be a removal in progress.
*/
if (spa->spa_removing_phys.sr_state == DSS_SCANNING)
return (SET_ERROR(EBUSY));
```
Changing the error code returned from that function changed
the behavior of the removal's library interface exposed to
the userland - `spa_vdev_remove()` now returns `EZFS_UNKNOWN`
instead of `EZFS_EBUSY` that was returning before.
This patch adds logic to make `spa_vdev_remove()` mindful
of the new EALREADY code and propagating `EZFS_EBUSY`
reverting to the previously established semantics of that
function.
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Closes#15013Closes#15129
The previous code was checking zfs_is_namespace_prop() only for the
last property on the list. If one was not "namespace", then remount
wasn't called. To fix that move zfs_is_namespace_prop() inside the
loop and remount if at least one of properties was "namespace".
Reviewed-by: Umer Saleem <usaleem@ixsystems.com>
Reviewed-by: Ameer Hamza <ahamza@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#15000
It was a vdev level read cache, designed to aggregate many small
reads by speculatively issuing bigger reads instead and caching
the result. But since it has almost no idea about what is going
on with exception of ZIO_FLAG_DONT_CACHE flag set by higher layers,
it was found to make more harm than good, for which reason it was
disabled for the past 12 years. These days we have much better
instruments to enlarge the I/Os, such as speculative and prescient
prefetches, I/O scheduler, I/O aggregation etc.
Besides just the dead code removal this removes one extra mutex
lock/unlock per write inside vdev_cache_write(), not otherwise
disabled and trying to do some work.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14953
Added a flag '-e' in zpool scrub to scrub only blocks in error log. A
user can pause, resume and cancel the error scrub by passing additional
command line arguments -p -s just like a regular scrub. This involves
adding a new flag, creating new libzfs interfaces, a new ioctl, and the
actual iteration and read-issuing logic. Error scrubbing is executed in
multiple txg to make sure pool performance is not affected.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Co-authored-by: TulsiJain tulsi.jain@delphix.com
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#8995Closes#12355
zpool initialize functions well for touching every free byte...once.
But if we want to do it again, we're currently out of luck.
So let's add zpool initialize -u to clear it.
Co-authored-by: Rich Ercolani <rincebrain@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12451Closes#14873
When the special_small_blocks property is being set during a pool
create it enforces a limit of 128KiB even if the pool's record size
is larger.
If the recordsize property is being set during a pool create, then
use that value instead of the default SPA_OLD_MAXBLOCKSIZE value.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <dev.fs.zfs@gmail.com>
Closes#13815Closes#14811
FreeBSD/powerpc64 is all ELFv2 since FreeBSD 13, even big endian. The
existing sha256 and sha512 asm code assumes that BE is all ELFv1, and LE
is ELFv2. Minor changes to add ELFv2 in the BE side gets this working
correctly on FreeBSD with latest OpenZFS import.
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Justin Hibbits <chmeeedalf@gmail.com>
Closes#14779
Add loongarch64 definitions & lua module setjmp asm
LoongArch is a new RISC ISA, which is a bit like MIPS or RISC-V.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Han Gao <gaohan@uniontech.com>
Signed-off-by: WANG Xuerui <xen0n@gentoo.org>
Closes#13422
Usage:
zpool set org.freebsd:comment="this is my pool" poolname
Tests are based on zfs_set's user property tests.
Also stop truncating property values at MAXNAMELEN, use ZFS_MAXPROPLEN.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Mateusz Piotrowski <mateusz.piotrowski@klarasystems.com>
Sponsored-by: Beckhoff Automation GmbH & Co. KG.
Sponsored-by: Klara Inc.
Closes#11680
And add it to the AVZ, this is not backwards compatible with older pools
due to an assertion in spa_sync() that verifies the number of ZAPs of
all vdevs matches the number of ZAPs in the AVZ.
Granted, the assertion only applies to #DEBUG builds - still, a feature
flag is introduced to avoid the assertion, com.klarasystems:vdev_zaps_v2
Notably, this allows to get/set properties on the root vdev:
% zpool set user:prop=value <pool> root-0
Before this commit, it was already possible to get/set properties on
top-level vdevs with the syntax <type>-<vdev_id> (e.g. mirror-0):
% zpool set user:prop=value <pool> mirror-0
This syntax also applies to the root vdev as it is is of type 'root'
with a vdev_id of 0, root-0. The keyword 'root' as an alias for
'root-0'.
The following tests have been added:
- zpool get all properties from root vdev
- zpool set a property on root vdev
- verify root vdev ZAP is created
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Wing <rob.wing@klarasystems.com>
Sponsored-by: Seagate Technology
Submitted-by: Klara, Inc.
Closes#14405
f6a0dac84 modified the zfs_iter_* functions to take a new "flags"
parameter, and introduced a variety of flags to ask the kernel to limit
the results in various ways, reducing the amount of work the caller
needed to do to filter out things they didn't need.
Unfortunately this change broke the ABI for existing clients (read:
older versions of the `zfs` program), and was reverted 399b98198.
dc95911d2 reintroduced the original patch, with the understanding that a
backwards-compatible fix would be made before the 2.2 release branch was
tagged. This commit is that fix.
This introduces zfs_iter_*_v2 functions that have the new flags
argument, and reverts the existing functions to not have the flags
parameter, as they were before. The old functions are now reimplemented
in terms of the new, with flags set to 0.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Wilson <george.wilson@delphix.com>
Original-patch-by: George Wilson <george.wilson@delphix.com>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Sponsored-by: Klara, Inc.
Closes#14597
Running `zfs list -o avail rpool` resulted in a core dump.
This commit will fix this.
Run the needed overhead only, when `use_color()` is true.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Wilson <gwilson@delphix.com>
Signed-off-by: Tino Reichardt <milky-zfs@mcmilk.de>
Closes#14712
Commit 11913870 (#14567) added cmn_err_once() by #define'ing a
compound statement but failed to consider usage in a single
statement brace-less if else.
Fix the problem by using the common "do {} while (0)" construct.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Attila Fülöp <attila@fueloep.org>
Closes#14629
Under some configurations, GCC didn't predefined macro 'powerpc' for
such a target. Use the guaranteed macro '__powerpc__' instead.
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: WHR <msl0000023508@gmail.com>
Closes#14631
After addressing coverity complaints involving `nvpair_name()`, the
compiler started complaining about dropping const. This lead to a rabbit
hole where not only `nvpair_name()` needed to be constified, but also
`nvpair_value_string()`, `fnvpair_value_string()` and a few other static
functions, plus variable pointers throughout the code. The result became
a fairly big change, so it has been split out into its own patch.
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14612
discover_cached_paths() will write a NULL into a string from a nvlist to
use it as a substring, but does not restore it before return. This
corrupts the nvlist. It should be harmless unless the string is needed
again later, but we should not do this, so let us fix it.
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14612
The strings returned from parsing nvlists should be immutable, but to
simplify the code when we want a substring from it, we sometimes will
write a NULL into it and then restore the value afterward. Provided
there is no concurrent access, this is okay, unless we forget to restore
the value afterward. This was caught when constifying string functions
related to nvlists.
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14612
Currently calls to kfpu_begin() and kfpu_end() are split between
the init() and fini() functions of the particular SIMD
implementation. This was done in #14247 as an optimization measure
for the ABD adapter. Unfortunately the split complicates FPU
handling on platforms that use a local FPU state buffer, like
Windows and macOS.
To ease porting, we introduce a boolean struct member in
fletcher_4_ops_t, indicating use of the FPU, and move the FPU state
handling from the SIMD implementations to the call sites.
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Signed-off-by: Attila Fülöp <attila@fueloep.org>
Closes#14600
We may try to build ZFS inside container too,
but let's just sync them for now.
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: George Melikov <mail@gmelikov.ru>
Closes#14605
Block Cloning allows to manually clone a file (or a subset of its
blocks) into another (or the same) file by just creating additional
references to the data blocks without copying the data itself.
Those references are kept in the Block Reference Tables (BRTs).
The whole design of block cloning is documented in module/zfs/brt.c.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Christian Schwarz <christian.schwarz@nutanix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Rich Ercolani <rincebrain@gmail.com>
Signed-off-by: Pawel Jakub Dawidek <pawel@dawidek.net>
Closes#13392
The intent is that this is like ENOTSUP, but specifically for when
something can't be done because we have no support for the requested
crypto parameters; eg unlocking a dataset or receiving a stream
encrypted with a suite we don't support.
Its not intended to be recoverable without upgrading ZFS itself.
If the request could be made to work by enabling a feature or modifying
some other configuration item, then some other code should be used.
load-key: In the future we might have more crypto suites (ie new values
for the `encryption` property. Right now trying to load a key on such
a future crypto suite will look up suite parameters off the end of the
crypto table, resulting in misbehaviour and/or crashes (or, with debug
enabled, trip the assertion in `zio_crypt_key_unwrap`).
Instead, lets check the value we got from the dataset, and if we can't
handle it, abort early.
recv: When receiving a raw stream encrypted with an unknown crypto
suite, `zfs recv` would report a generic `invalid backup stream`
(EINVAL). While technically correct, its not super helpful, so lets
ship a more specific error code and message.
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Rob Norris <robn@despairlabs.com>
Closes#14577
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Attila Fülöp <attila@fueloep.org>
Closes#14567
The skeleton file module/icp/include/generic_impl.c can be used for
iterating over different implementations of algorithms.
It is used by SHA256, SHA512 and BLAKE3 currently.
The Solaris SHA2 implementation got replaced with a version which is
based on public domain code of cppcrypto v0.10.
These assembly files are taken from current openssl master:
- sha256-x86_64.S: x64, SSSE3, AVX, AVX2, SHA-NI (x86_64)
- sha512-x86_64.S: x64, AVX, AVX2 (x86_64)
- sha256-armv7.S: ARMv7, NEON, ARMv8-CE (arm)
- sha512-armv7.S: ARMv7, NEON (arm)
- sha256-armv8.S: ARMv7, NEON, ARMv8-CE (aarch64)
- sha512-armv8.S: ARMv7, ARMv8-CE (aarch64)
- sha256-ppc.S: Generic PPC64 LE/BE (ppc64)
- sha512-ppc.S: Generic PPC64 LE/BE (ppc64)
- sha256-p8.S: Power8 ISA Version 2.07 LE/BE (ppc64)
- sha512-p8.S: Power8 ISA Version 2.07 LE/BE (ppc64)
Tested-by: Rich Ercolani <rincebrain@gmail.com>
Tested-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tino Reichardt <milky-zfs@mcmilk.de>
Closes#13741
These are added via HWCAP interface:
- zfs_neon_available() for arm and aarch64
- zfs_sha256_available() for arm and aarch64
- zfs_sha512_available() for aarch64
This one via cpuid() call:
- zfs_shani_available() for x86_64
Tested-by: Rich Ercolani <rincebrain@gmail.com>
Tested-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tino Reichardt <milky-zfs@mcmilk.de>
Closes#13741
We had three sha2.h headers in different places.
The FreeBSD version, the Linux version and the generic solaris version.
The only assembly used for acceleration was some old x86-64 openssl
implementation for sha256 within the icp module.
For FreeBSD the whole SHA2 files of FreeBSD were copied into OpenZFS,
these files got removed also.
Tested-by: Rich Ercolani <rincebrain@gmail.com>
Tested-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tino Reichardt <milky-zfs@mcmilk.de>
Closes#13741
In commit 0a5b942d4 the FreeBSD SECTION_STATIC macro was set to
".rodata". This assembler directive is supported by LLVM (as a
convenience alias for ".section .rodata") by not by GNU as.
This caused the FreeBSD builds that are done with gcc to fail.
Therefore, use ".section .rodata" instead, similar to the other
asm_linkage.h headers.
Reviewed-by: Mateusz Guzik <mjguzik@gmail.com>
Reviewed-by: Attila Fülöp <attila@fueloep.org>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Signed-off-by: Dimitry Andric <dimitry@andric.com>
Closes#14526
strlcat() is supposed to be given the length of the destination buffer,
including the existing contents. Unfortunately, I had been overzealous
when I wrote a51288aabb, since I gave it
the length of the destination buffer, minus the existing contents. This
likely caused a regression on large strings.
On the topic of being overzealous, the use of strlcat() in
dmu_send_estimate_fast() was unnecessary because recv_clone_name is a
fixed length string. We continue using strlcat() mostly as defensive
programming, in case the string length is ever changed, even though it
is unnecessary.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14476
In https://github.com/openzfs/zfs/pull/14228 the FreeBSD
SECTION_STATIC was set to ".data" instead of ".rodata". This
commit just restores it back to .rodata.
Reviewed-by: Attila Fülöp <attila@fueloep.org>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Closes#14460
We accidentally reused variable name "i" for inner and outer loops.
Reviewed-by: Rich Ercolani <Rincebrain@gmail.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Reno Reckling <e-github@wthack.de>
Closes#14452Closes#14445
After commit 19d3961, progress reporting (-v) with replication flag
enabled does not report the progress on the console. This commit
fixes the issue by updating the logic to check for pa->progress
instead of pa_verbosity in send_progress_thread().
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#14448
The .align directive used to align storage locations is
ambiguous. On some platforms and assemblers it takes a byte count,
on others the argument is interpreted as a shift value. The current
usage expects the first interpretation.
Replace it with the unambiguous .balign directive which always
expects a byte count, regardless of platform and assembler.
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Attila Fülöp <attila@fueloep.org>
Closes#14422
In the zstream code, Coverity reported:
"The argument could be controlled by an attacker, who could invoke the
function with arbitrary values (for example, a very high or negative
buffer size)."
It did not report this in the kernel. This is likely because the
userspace code stored this in an int before passing it into the
allocator, while the kernel code stored it in a uint32_t.
However, this did reveal a potentially real problem. On 32-bit systems
and systems with only 4GB of physical memory or less in general, it is
possible to pass a large enough value that the system will hang. Even
worse, on Linux systems, the kernel memory allocator is not able to
support allocations up to the maximum 4GB allocation size that this
allows.
This had already been limited in userspace to 64MB by
`ZFS_SENDRECV_MAX_NVLIST`, but we need a hard limit in the kernel to
protect systems. After some discussion, we settle on 256MB as a hard
upper limit. Attempting to receive a stream that requires more memory
than that will result in E2BIG being returned to user space.
Reported-by: Coverity (CID-1529836)
Reported-by: Coverity (CID-1529837)
Reported-by: Coverity (CID-1529838)
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14285
Introduce four new vdev properties:
checksum_n
checksum_t
io_n
io_t
These properties can be used for configuring the thresholds of zed's
diagnosis engine and are interpeted as <N> events in T <seconds>.
When this property is set to a non-default value on a top-level vdev,
those thresholds will also apply to its leaf vdevs. This behavior can be
overridden by explicitly setting the property on the leaf vdev.
Note that, these properties do not persist across vdev replacement. For
this reason, it is advisable to set the property on the top-level vdev
instead of the leaf vdev.
The default values for zed's diagnosis engine (10 events, 600 seconds)
remains unchanged.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Rob Wing <rob.wing@klarasystems.com>
Sponsored-by: Seagate Technology LLC
Closes#13805
If zfs_receive_one() gets back EINVAL, check for the more likely case,
embedded block pointers + encryption and return that error, before
falling back to the less likely case, a resumable stream when the
kernel has not been upgraded to support resume.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Sponsored-by: rsync.net
Sponsored-by: Klara Inc.
Closes#14379
Add new macro ASMABI used by Windows to change
calling API to "sysv_abi".
Reviewed-by: Attila Fülöp <attila@fueloep.org>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Closes#14228
This allows parsing of zfs send progress by checking the process
title.
Doing so requires some changes to the send code in libzfs_sendrecv.c;
primarily these changes move some of the accounting around, to allow
for the code to be verbose as normal, or set the process title. Unlike
BSD, setproctitle() isn't standard in Linux; thus, borrowed it from
libbsd with slight modifications.
Authored-by: Sean Eric Fagan <sef@FreeBSD.org>
Co-authored-by: Ryan Moeller <ryan@iXsystems.com>
Co-authored-by: Ameer Hamza <ahamza@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#14376
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Charles Suh <charles.suh@gmail.com>
Closes#14360
This commit supports for spare vdev hotplug. The
spare vdev associated with all the pools will be
marked as "Removed" when the drive is physically
detached and will become "Available" when the
drive is reattached. Currently, the spare vdev
status does not change on the drive removal and
the same is the case with reattachment.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#14295
There is a lock order inversion deadlock between `spa_errlog_lock` and
`dp_config_rwlock`:
A thread in `spa_delete_dataset_errlog()` is running from a sync task.
It is holding the `dp_config_rwlock` for writer (see
`dsl_sync_task_sync()`), and waiting for the `spa_errlog_lock`.
A thread in `dsl_pool_config_enter()` is holding the `spa_errlog_lock`
(see `spa_get_errlog_size()`) and waiting for the `dp_config_rwlock` (as
reader).
Note that this was introduced by #12812.
This commit address this by defining the lock ordering to be
dp_config_rwlock first, then spa_errlog_lock / spa_errlist_lock.
spa_get_errlog() and spa_get_errlog_size() can acquire the locks in this
order, and then process_error_block() and get_head_and_birth_txg() can
verify that the dp_config_rwlock is already held.
Additionally, a buffer overrun in `spa_get_errlog()` is corrected. Many
code paths didn't check if `*count` got to zero, instead continuing to
overwrite past the beginning of the userspace buffer at `uaddr`.
Tested by having some errors in the pool (via `zinject -t data
/path/to/file`), one thread running `zpool iostat 0.001`, and another
thread runs `zfs destroy` (in a loop, although it hits the first time).
This reproduces the problem easily without the fix, and works with the
fix.
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: George Amanakis <gamanakis@gmail.com>
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#14239Closes#14289
This adds support to color zfs diff (in the style of git diff)
conditional on the ZFS_COLOR environment variable.
Signed-off-by: Ethan Coe-Renner <coerenner1@llnl.gov>
Currently, the receiver fails to override the encryption
property for the plain replicated dataset with the error:
"cannot receive incremental stream: encryption property
'encryption' cannot be set for incremental streams.". The
problem is resolved by allowing the receiver to override
the encryption property for plain replicated send.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#14253Closes#13533
If the fields to be listed and sorted by are constrained to those
populated by dsl_dataset_fast_stat(), then zfs list is much faster,
as it does not need to open each objset and reads its properties.
A previous optimization by Pawel Dawidek
(0cee24064a) took advantage
of this to make listing snapshot names sorted only by name much faster.
However, it was limited to `-o name -s name`, this work extends this
optimization to work with:
- name
- guid
- createtxg
- numclones
- inconsistent
- redacted
- origin
and could be further extended to any other properties supported by
dsl_dataset_fast_stat() or similar, that do not require extra locking
or reading from disk.
This was committed before (9a9e2e343dfa2af28bf7910de77ae73aa006de62),
but was reverted due to a regression when used with an older kernel.
If the kernel does not populate zc->zc_objset_stats, we now fallback
to getting the properties via the slower interface, to avoid problems
with newer userland and older kernels.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Closes#14110
`zfs_send_cb_impl()` calls `dump_filesystems()`, which calls
`dump_filesystem()`, which will return `-1` as an error when
`zfs_open()` returns `NULL`.
This will be passed to `zfs_standard_error()`, which passes it to
`zfs_standard_error_fmt()`, which passes it to `strerror()`.
To fix this, we modify zfs_open() to set `errno` whenever it returns
NULL. Most of the cases already have `errno` set (since they pass it to
`zfs_standard_error_fmt()`, which makes this easy. Then we modify
`dump_filesystem()` to pass `errno` instead of `-1`.
Reported-by: Coverity (CID-1524598)
Reviewed-by: Damian Szuberski <szuberskidamian@gmail.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14264
Squelch false positives reported by GCC 12 with UBSan.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: szubersk <szuberskidamian@gmail.com>
Closes#14150
