When configure is run with --with-spec=redhat, and rpms are built, the
kmod-zfs-devel package is missing
Provides: kmod-spl-devel = %{version}
which is required by software such as Lustre which builds against zfs
kmods. Adding it makes it easier for such software to build against
both zfs-0.7 (where SPL is separate and may be missing) and zfs-0.8.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#8930
The mmp_interval test case was failing on Fedora 30 due to the built-in
'echo' command terminating the script when it was unable to write to
the sysfs module parameter. This change in behavior was observed with
ksh-2020.0.0-alpha1. Resolve the issue by using the external cat
command which fails gracefully as expected.
Additionally, remove some incorrect quotes around the $? return values.
Reviewed-by: Giuseppe Di Natale <guss80@gmail.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8906
For busy ARC situation when arc_size close to arc_c is desired. But
then it is quite likely that aggsum_compare(&arc_size, arc_c) will need
to flush per-CPU buckets to find exact comparison result. Doing that
often in a hot path penalizes whole idea of aggsum usage there, since it
replaces few simple atomic additions with dozens of lock acquisitions.
Replacing aggsum_compare() with aggsum_upper_bound() in code increasing
arc_p when ARC is growing (arc_size < arc_c) according to PMC profiles
allows to save ~5% of CPU time in aggsum code during sequential write
to 12 ZVOLs with 16KB block size on large dual-socket system.
I suppose there some minor arc_p behavior change due to lower precision
of the new code, but I don't think it is a big deal, since it should
affect only very small window in time (aggsum buckets are flushed every
second) and in ARC size (buckets are limited to 10 average ARC blocks
per CPU).
Reviewed-by: Chris Dunlop <chris@onthe.net.au>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Allan Jude <allanjude@freebsd.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#8901
Don't require Python at configure/build unless building pyzfs.
Move ZFS_AC_PYTHON_MODULE to always-pyzfs.m4 where it is used.
Make test syntax more consistent.
Sponsored by: iXsystems, Inc.
Reviewed-by: Neal Gompa <ngompa@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#8895
`lz4_decompress_abd` is declared in zio_compress.h but it is not defined
anywhere. The declaration should be removed.
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed-by: Allan Jude <allanjude@freebsd.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
External-issue: DLPX-47477
Closes#8894
If the zfs_remove_max_segment tunable is changed to be not a multiple of
the sector size, then the device removal code will malfunction and try
to create mappings that are smaller than one sector, leading to a panic.
On debug bits this assertion will fail in spa_vdev_copy_segment():
ASSERT3U(DVA_GET_ASIZE(&dst), ==, size);
On nondebug, the system panics with a stack like:
metaslab_free_concrete()
metaslab_free_impl()
metaslab_free_impl_cb()
vdev_indirect_remap()
free_from_removing_vdev()
metaslab_free_impl()
metaslab_free_dva()
metaslab_free()
Fortunately, the default for zfs_remove_max_segment is 1MB, so this
can't occur by default. We hit it during this test because
removal_remap.ksh changes zfs_remove_max_segment to 1KB. When testing on
4KB-sector disks, we hit the bug.
This change makes the zfs_remove_max_segment tunable more robust,
automatically rounding it up to a multiple of the sector size. We also
turn some key assertions into VERIFY's so that similar bugs would be
caught before they are encoded on disk (and thus avoid a
panic-reboot-loop).
Reviewed-by: Sean Eric Fagan <sef@ixsystems.com>
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: Sebastien Roy <sebastien.roy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
External-issue: DLPX-61342
Closes#8893
Starting in sync pass 5 (zfs_sync_pass_dont_compress), we disable
compression (including of metadata). Ostensibly this helps the sync
passes to converge (i.e. for a sync pass to not need to allocate
anything because it is 100% overwrites).
However, in practice it increases the average number of sync passes,
because when we turn compression off, a lot of block's size will change
and thus we have to re-allocate (not overwrite) them. It also increases
the number of 128KB allocations (e.g. for indirect blocks and spacemaps)
because these will not be compressed. The 128K allocations are
especially detrimental to performance on highly fragmented systems,
which may have very few free segments of this size, and may need to load
new metaslabs to satisfy 128K allocations.
We should increase zfs_sync_pass_dont_compress. In practice on a highly
fragmented system we see a few 5-pass txg's, a tiny number of 6-pass
txg's, and no txg's with more than 6 passes.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: George Wilson <george.wilson@delphix.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
External-issue: DLPX-63431
Closes#8892
Memory copy is too heavy operation to do under the congested lock.
Moving it out reduces congestion by many times to almost invisible.
Since the original zio removed from the queue, and the child zio is
not executed yet, I don't see why would the copy need protection.
My guess it just remained like this from the time when lock was not
dropped here, which was added later to fix lock ordering issue.
Multi-threaded sequential write tests with both HDD and SSD pools
with ZVOL block sizes of 4KB, 16KB, 64KB and 128KB all show major
reduction of lock congestion, saving from 15% to 35% of CPU time
and increasing throughput from 10% to 40%.
Reviewed-by: Richard Yao <ryao@gentoo.org>
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#8890
This change restricts filesystem creation if the given name
contains either '.' or '..'
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Signed-off-by: TulsiJain <tulsi.jain@delphix.com>
Closes#8842Closes#8564
When running zloop, we occasionally see the following crash:
dmu_tx_assign(tx, TXG_WAIT) == 0 (0x1c == 0)
ASSERT at ../../module/zfs/vdev_removal.c:1507:spa_vdev_remove_thread()/sbin/ztest(+0x89c3)[0x55faf567b9c3]
The error value 0x1c is ENOSPC.
The transaction used by spa_vdev_remove_thread() should not be able to
fail due to being out of space. i.e. we should not call
dmu_tx_hold_space(). This will allow the removal thread to schedule its
work even when the pool is low on space. The "slop space" will provide
enough free space to sync out the txg.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
External-issue: DLPX-37853
Closes#8889
sysfs_attr_init() is required to make lockdep happy for dynamically
allocated sysfs attributes. This fixed#8868 on Fedora 29 running
kernel-debug.
This requirement was introduced in 2.6.34.
See include/linux/sysfs.h for what it actually does.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@gmail.com>
Closes#8868Closes#8884
When iterating over a ZAP object, we're almost always certain to iterate
over the entire object. If there are multiple leaf blocks, we can
realize a performance win by issuing reads for all the leaf blocks in
parallel when the iteration begins.
For example, if we have 10,000 snapshots, "zfs destroy -nv
pool/fs@1%9999" can take 30 minutes when the cache is cold. This change
provides a >3x performance improvement, by issuing the reads for all ~64
blocks of each ZAP object in parallel.
Reviewed-by: Andreas Dilger <andreas.dilger@whamcloud.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
External-issue: DLPX-58347
Closes#8862
Sometimes the target ARC size is reduced to arc_c_min, which impacts
performance. We've seen this happen as part of the random_reads
performance regression test, where the ARC size is reduced before the
reads test starts which impacts how long it takes for system to reach
good IOPS performance.
We call arc_reduce_target_size when arc_reap_cb_check() returns TRUE,
and arc_available_memory() is less than arc_c>>arc_shrink_shift.
However, arc_available_memory() could easily be low, even when arc_c is
low, because we can have tons of unused bufs in the abd kmem cache. This
would be especially true just after the DMU requests a bunch of stuff be
evicted from the ARC (e.g. due to "zpool export").
To fix this, the ARC should reduce arc_c by the requested amount, not
all the way down to arc_size (or arc_c_min), which can be very small.
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
External-issue: DLPX-59431
Closes#8864
The udevadm settle timeout can be 120 or 180 seconds by default
for some distributions. If a long delay is experienced, it could
be due to some strangeness in a malfunctioning device that isn't
related to the devices under test. To help debug this condition,
a notice is given if settle takes too long.
Arguments can now be passed to block_device_wait. The expected
arguments are block device pathnames.
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Giuseppe Di Natale <guss80@gmail.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Elling <Richard.Elling@RichardElling.com>
Closes#8839
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Giuseppe Di Natale <guss80@gmail.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Elling <Richard.Elling@RichardElling.com>
Closes#8839
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Giuseppe Di Natale <guss80@gmail.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Elling <Richard.Elling@RichardElling.com>
Closes#8839
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Giuseppe Di Natale <guss80@gmail.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Elling <Richard.Elling@RichardElling.com>
Closes#8839
On large systems, the memory used by loaded metaslabs can become
a concern. While range trees are a fairly efficient data structure,
on heavily fragmented pools they can still consume a significant
amount of memory. This problem is amplified when we fail to unload
metaslabs that we aren't using. Currently, we only unload a metaslab
during metaslab_sync_done; in order for that function to be called
on a given metaslab in a given txg, we have to have dirtied that
metaslab in that txg. If the dirtying was the result of an allocation,
we wouldn't be unloading it (since it wouldn't be 8 txgs since it
was selected), so in effect we only unload a metaslab during txgs
where it's being freed from.
We move the unload logic from sync_done to a new function, and
call that function on all metaslabs in a given vdev during
vdev_sync_done().
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#8837
Build process would always re-compile spa_history.c due to touching
zfs_gitrev.h - avoid if no change in gitrev.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Chris Dunlop <chris@onthe.net.au>
Reviewed-by: Allan Jude <allanjude@freebsd.org>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Closes#8860
Reviewed-by: Chris Dunlop <chris@onthe.net.au>
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Signed-off-by: Allan Jude <allanjude@freebsd.org>
Closes#8822
Historically while doing performance testing we've noticed that IOPS
can be significantly reduced when all vdevs in the pool are hitting
the zfs_mg_fragmentation_threshold percentage. Specifically in a
hypothetical pool with two vdevs, what can happen is the following:
Vdev A would go above that threshold and only vdev B would be used.
Then vdev B would pass that threshold but vdev A would go below it
(we've been freeing from A to allocate to B). The allocations would
go back and forth utilizing one vdev at a time with IOPS taking a hit.
Empirically, we've seen that our vdev selection for allocations is
good enough that fragmentation increases uniformly across all vdevs
the majority of the time. Thus we set the threshold percentage high
enough to avoid hitting the speed bump on pools that are being pushed
to the edge. We effectively disable its effect in the majority of the
cases but we don't remove (at least for now) just in case we hit any
weird behavior in the future.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Signed-off-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Closes#8859
Since zfs_znode_alloc() already takes dmu_buf_t*, taking another
uint64_t argument for objid is redundant. inode's ->i_ino does and
needs to match znode's ->z_id.
zfs_znode_alloc() in FreeBSD and illumos doesn't have this argument
since vnode doesn't have vnode# in VFS (hence ->z_id exists).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@osnexus.com>
Closes#8841
Per suggestion from @behlendorf in #8777, remove vn_set_fs_pwd() and
vn_set_pwd() which are only used in zfs_ioctl.c:_init() while loading
zfs.ko.
The rest of initialization functions being called here after cwd set
to / don't depend on cwd of the process except for spa_config_load().
spa_config_load() uses a relative path ".//etc/zfs/zpool.cache" when
`rootdir` is non-NULL, which is "/etc/zfs/zpool.cache" given cwd is /,
so just unconditionally use the absolute path without "./", so that
`vn_set_pwd("/")` as well as the entire functions can be removed.
This is also what FreeBSD does.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@osnexus.com>
Closes#8826
For recursive renaming, simplify the code by moving `zhrp` and
`parentname` to inner scope. `zhrp` is only used to test existence
of a parent dataset for recursive dataset dir scan since ba6a24026c.
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Giuseppe Di Natale <guss80@gmail.com>
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@osnexus.com>
Closes#8815
s/get_vdev_spec/make_root_vdev
The former doesn't exist anymore.
Sponsored by: iXsystems, Inc.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: Ryan Moeller <ryan@freqlabs.com>
Closes#8759
These descriptions are not uptodate with the code.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@gmail.com>
Closes#8767
In `config/kernel-timer.m4` refactor slightly to check more generally
for the new `timer_setup()` APIs, but also check the callback signature
because some kernels (notably 4.14) have the new `timer_setup()` API but
use the old callback signature. Also add a check for a `flags` member in
`struct timer_list`, which was added in 4.1-rc8.
Add compatibility shims to `include/spl/sys/timer.h` to allow using the
new timer APIs with the only two caveats being that the callback
argument type must be declared as `spl_timer_list_t` and an explicit
assignment is required to get the timer variable for the `timer_of()`
macro. So the callback would look like this:
```c
__cv_wakeup(spl_timer_list_t t)
{
struct timer_list *tmr = (struct timer_list *)t;
struct thing *parent = from_timer(parent, tmr,
parent_timer_field);
... /* do stuff with parent */
```
Make some minor changes to `spl-condvar.c` and `spl-taskq.c` to use the
new timer APIs instead of conditional code.
Reviewed-by: Tomohiro Kusumi <kusumi.tomohiro@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rafael Kitover <rkitover@gmail.com>
Closes#8647
When ARC size is very small, aggsum_lower_bound(&arc_size) may return
negative values, that due to unsigned comparison caused delays, waiting
for arc_adjust() to "fix" it by calling aggsum_value(&arc_size). Use
of signed comparison there fixes the problem.
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#8873
This patch fixes an incorrect error message that comes up when
doing a non-forcing, raw, incremental receive into a dataset
that has a newer snapshot than the "from" snapshot. In this
case, the current code prints a confusing message about an IVset
guid mismatch.
This functionality is supported by non-raw receives as an
undocumented feature, but was never supported by the raw receive
code. If this is desired in the future, we can probably figure
out a way to make it work.
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Issue #8758Closes#8863
This matches the behavior of other python scripts, such as arcstat and
dbufstat, which are always installed but whose install-exec-hook actions
will simply touch up the shebang if a python interpreter was configured
*and* that interpreter is a python2 interpreter.
Fixes installation in a minimal build chroot without python available.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@freqlabs.com>
Signed-off-by: Eli Schwartz <eschwartz@archlinux.org>
Closes#8851
During zfs-kmod RPM build, $(uname -r) gets unintentionally evaluated on
the build host, once and for all. It should be evaluated during the
execution of the scriptlets on the installation host. Escaping the $
character avoids evaluating it during build.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Reviewed-by: Neal Gompa <ngompa@datto.com>
Signed-off-by: Samuel Verschelde <stormi-xcp@ylix.fr>
Closes#8866
This patch re-adds a check that was removed in 369aa50. The check
confirms that a raw receive is not occuring before truncating an
object's dn_maxblkid. At the time, it was believed that all cases
that would hit this code path would be handled in other places,
but that was not the case.
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#8852Closes#8857
The ZFS on-disk format stores each inode's generation ID as a 64
bit number on disk and in-core. However, the Linux kernel's inode
is only a 32 bit number. In most places, the code handles this
correctly, but the cast is missing in zfs_rezget(). For many pools,
this isn't an issue since the generation ID is computed as the
current txg when the inode is created and many pools don't have
more than 2^32 txgs.
For the pools that have more txgs, this issue causes any inode with
a high enough generation number to report IO errors after a call to
"zfs rollback" while holding the file or directory open. This patch
simply adds the missing cast.
Reviewed-by: Alek Pinchuk <apinchuk@datto.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#8858
The build for test binary hkdf_test was linking both against libicp
and libzpool. This results in two instances of libicp inside the
binary but the call to icp_init() only initializes one of them!
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Don Brady <don.brady@delphix.com>
Closes#8850
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Chris Dunlop <chris@onthe.net.au>
Signed-off-by: Peter Wirdemo <peter.wirdemo@gmail.com>
Closes#8855
If ZFS is built with enable_linux_builtin, it seems to be possible
to compile the kernel with TRIM_UNUSED_KSYM.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Torsten Wörtwein <twoertwein@gmail.com>
Closes#8820
Previously, --without-python would cause ./configure to fail. Now it is
able to proceed, and the Python scripts will not be built.
Use portable parameter expansion matching instead of nonstandard
substring matching to detect the Python version. This test is
duplicated in several places, so define a function for it.
Don't assume the full path to binaries, since different platforms do
install things in different places. Use AC_CHECK_PROGS instead.
When building without Python, also build without pyzfs.
Sponsored by: iXsystems, Inc.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Eli Schwartz <eschwartz93@gmail.com>
Signed-off-by: Ryan Moeller <ryan@freqlabs.com>
Closes#8809Closes#8731
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: DHE <git@dehacked.net>
Closes#8733Closes#8752
This reverts commit ec4f9b8f30 which introduced a narrow race which
can lead to lseek(, SEEK_DATA) incorrectly returning ENXIO. Resolve
the issue by revering this change to restore the previous behavior
which depends solely on checking the dirty list.
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8816Closes#8834
Add tests for
97aa3ba44("Fix link count of root inode when snapdir is visible")
as suggested in #8727.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@osnexus.com>
Closes#8732
When opening a log device during import its allocation bias will
not yet have been set by vdev_load(). This results in the log
device's ashift being incorrectly applied to the maximum ashift
of the vdevs in the normal class. Which in turn prevents the
removal of any top-level devices due to the ashift check in the
spa_vdev_remove_top_check() function.
This issue is resolved by including vdev_islog in the check since
it will be set correctly during vdev_open().
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8735
dn->dn_datablksz type is uint32_t and need to be casted to uint64_t
to avoid an overflow when the record size is greater than 4 MiB.
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olivier Mazouffre <olivier.mazouffre@ims-bordeaux.fr>
Closes#8778Closes#8797
This commits fixes a double-free in zfs_ioc_pool_create() triggered by
specifying an unsupported combination of properties when creating a pool
with encryption enabled.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#8791
files in dist_*_SCRIPTS get installed with 0755, those in dist_*_DATA
with 0644. This commit moves all .kshlib, .shlib and .cfg files in the
testsuite to dist_pkgdata_DATA, and removes the shebang from
zpool_import.kshlib.
This ensures that the files are installed with appropriate permissions
and silences some warnings from lintian
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Stoiko Ivanov <s.ivanov@proxmox.com>
Closes#8803
